Embroidery Machine

Version：2009-01
Computerized Embroidery Machine
B E C S – 316/366
Owner's Manual
CERTIFICATE OF CONFORMITY OF
QUALITY MANAGEMENT SYSTEM
CERTIFICATION
This is to certify that the quality system of

Beijing Xingdahao Technology Co., Ltd.
Is in conformity with
GB/T 19001-2000 idt ISO 9001:2000 Standard
This certificate is valid to the following product(s)/service:

Design and manufacture of computerize sewing
equipment control system
Registration No.:0203Q15748R2M
ACCREDITED BY MEMBER OF
THE IAF MIA FOR QMS
INDEX
INDEX
Chapter 1 General Descriptions ................................................................................................. 2
1-1 Warnings and Cautions................................................................................................ 2

1-2 Main Features .............................................................................................................. 2
1-3 Main Functions ............................................................................................................ 2
Chapter 2 Names of Parts about Electrical Control System ...................................................... 2
2-1 Operation Control Panel .............................................................................................. 2

2-2 Operation Bar and Turn Shaft Button.......................................................................... 2
2-3 Darning Switch ............................................................................................................ 2
Chapter 3 How to Start Embroidery........................................................................................... 2
3-1 Summary...................................................................................................................... 2
3-2 Input a Design into Memory from Floppy Disk .......................................................... 2
3-3 Preparation before Embroidering................................................................................. 2
3-4 Select a Design for Embroidery and Confirm to Embroider the Design ..................... 2
3-5 Normal Embroidering, Returning and Darning Embroidering.................................... 2
3-6 Release Embroidery Confirmation Status.................................................................... 2
Chapter 4 Normal Embroidery and Idling ................................................................................. 2
4-1 Relations between Normal Embroidery and Idling ..................................................... 2

4-2 Low-speed Idling ......................................................................................................... 2
4-3 High-speed Idling ........................................................................................................ 2
4-4 Release of Low-speed/High-speed Idling.................................................................... 2
4-5 Positioning Idling......................................................................................................... 2
Chapter 5 Color-change Management ....................................................................................... 2
5-1 Manual Needle-change (Color-change) when Stop..................................................... 2

5-2 Manual Color-change and Manual Start during Embroidering ................................... 2
5-3 Automatic Color-change and Manual Start (or Automatic Start) during Embroidery 2
5-4 Setting Automatic Color-change Sequence (or Color Line)........................................ 2
5-5 Storing the Manual Color-change Number into Color Line ........................................ 2
BECS-316/366 Computerized Embroidery Machine’s Manual I

INDEX
5-6 The Color-change Speed.............................................................................................. 2
Chapter 6 Setting Design Direction ........................................................................................... 2
Chapter 7 Frame Management ................................................................................................... 2
7-1 Manual Frame Shifting ................................................................................................ 2

7-2 Returning to Origin Point ............................................................................................ 2
7-3 Restore Design’s Origin Point ..................................................................................... 2
7-4 Save Design’s Origin Point.......................................................................................... 2
7-5 Automatically Set the Origin Point.............................................................................. 2
7-6 Moving Frame along the Border.................................................................................. 2
7-7 Returning to Origin...................................................................................................... 2
7-8 Returning to the Stop-embroidery Point...................................................................... 2
Chapter 8 Embroidery Speed (Main Shaft Speed)..................................................................... 2
8-1 Setting the Limit Speed................................................................................................ 2

8-2 Setting Embroidering Speed ........................................................................................ 2
Chapter 9 Trimming Thread....................................................................................................... 2
9-1 Automatic Trimming Thread ....................................................................................... 2

9-2 Manual Trimming Thread............................................................................................ 2
Chapter 10 Disk Management...................................................................................................... 2
10-1 Directory Listing of Disk............................................................................................. 2

10-2 Input Design from Disk to Memory ............................................................................ 2
10-3 Output Design from Memory to Disk.......................................................................... 2
10-4 Deleting the Design in Floppy Disk ............................................................................ 2
10-5 Formatting a 720KB Disk............................................................................................ 2
10-6 Formatting a 1.44MB Disk .......................................................................................... 2
Chapter 11 Displaying Parameters and Displaying Language Selection..................................... 2
11-1 Viewing the Common Parameters ............................................................................... 2

11-2 Clearing Accumulated Stitch Count and X/Y Displacement....................................... 2
11-3 Switching of Display Language................................................................................... 2
Chapter 12 Other management and Setting the Parameters......................................................... 2
II BECS-316/366 Computerized Embroidery Machine’s Manual

INDEX
12-1 Setting of Magnification, Rotation and Repetition...................................................... 2

12-2 Operation of Design Periphery .................................................................................... 2
12-3 Setting the Offset Point................................................................................................ 2
12-4 Setting Frame Protection when Power Off (Setting the Machine’s Zero Point) ......... 2
12-5 Frame Restoring after Power Off................................................................................. 2
12-6 Demanding whether Setup Frame Zero Point or not ................................................... 2
12-7 Setting the Machine Parameters .................................................................................. 2
12-8 Setting Parameters of Sequin, Special Emb, etc.......................................................... 2
12-9 Compensating of Satin Stitches ................................................................................... 2
12-10 Set Date & Time .......................................................................................................... 2
Chapter 13 Management of Design in Memory........................................................................... 2
13-1 Select a Design for Embroidery................................................................................... 2

13-2 List the Design in Memory .......................................................................................... 2
13-3 Input a Design into Memory from Floppy Disk .......................................................... 2
13-4 Copy the Design........................................................................................................... 2
13-5 Delete the Design......................................................................................................... 2
13-6 Divide the Design ........................................................................................................ 2
13-7 Splice two Designs....................................................................................................... 2
13-8 Editing the Packed Design........................................................................................... 2
13-9 Clear All Designs in Memory...................................................................................... 2
Chapter 14 Edit of the Design in Memory ................................................................................... 2
14-1 Entering the Edit of Design in Memory....................................................................... 2

14-2 How to Edit a Stitch..................................................................................................... 2
14-3 Rapidly Searching a Stitch........................................................................................... 2
14-4 Rapidly Searching a Special Stitch.............................................................................. 2
14-5 Block Operation........................................................................................................... 2
14-6 Help for Editing ........................................................................................................... 2
14-7 Saving the Editing Design and Exit............................................................................. 2
14-8 Quitting the Editing ..................................................................................................... 2
Chapter 15 Operation Help .......................................................................................................... 2
BECS-316/366 Computerized Embroidery Machine’s Manual III

INDEX
Chapter 16 Monogramming and Making a High-speed Design .................................................. 2
16-1 monogramming (optional) ........................................................................................... 2

16-2 Making a High-speed Design ...................................................................................... 2
Chapter 17 Compile the Packed Design and Embroidering Design ............................................ 2
17-1 Compile the Packed Design......................................................................................... 2

17-2 Compile the Embroidering Design .............................................................................. 2
Chapter 18 Initialize the System Parameters during Electrifying................................................ 2
Chapter 19 Adding Patch Code to a Design................................................................................. 2
Chapter 20 The Enhanced Functions of Dot Key ........................................................................ 2
20-1 Turn the Main Axis at 100 Degree Manually .............................................................. 2

20-2 Let the Needle Sew Down and Move the Frame ......................................................... 2
20-3 Switching On/Off of Valves in Quilt Embroidery....................................................... 2
20-4 Manual Operation of Sequin Embroidery.................................................................... 2
20-5 M Axis Operation of Taping Embroidery.................................................................... 2
20-6 Operation of Clamp Foot ............................................................................................. 2
Chapter 21 Shift the Frame to Make a New Design .................................................................... 2
Chapter 22 Setting the Cyclic Embroidering ............................................................................... 2
Chapter 23 Adjust the Machine's Braking (for Manufacturer) .................................................... 2
23-1 Summary...................................................................................................................... 2
23-2 Setting Parameters of "SET BRAKE PARA." and "MAIN MOTOR PARA."........... 2
Chapter 24 Let the Needle Sew Down and Move the Frame....................................................... 2
Chapter 25 No Output of the Design in Memory......................................................................... 2
25-1 Summary...................................................................................................................... 2
25-2 Setting a Password for "NO OUTPUTTING DESIGN" ............................................. 2
25-3 Canceling the Password for "NO OUTPUTTING DESIGN" ..................................... 2
Chapter 26 Testing ....................................................................................................................... 2
IV BECS-316/366 Computerized Embroidery Machine’s Manual

INDEX
26-1 Computer Testing ........................................................................................................ 2

26-2 Encoder Testing ........................................................................................................... 2
26-3 Main Shaft Speed Testing............................................................................................ 2
26-4 Mechanical Testing...................................................................................................... 2
26-5 Turn the Main Shaft to Any Angle .............................................................................. 2
Chapter 27 Embroidering Management and Errors Statistics...................................................... 2
27-1 Management Information in the Main Picture............................................................. 2

27-2 Statistic about embroidering ........................................................................................ 2
Chapter 28 Generating the Outline Design .................................................................................. 2
28-1 Summary...................................................................................................................... 2
28-2 Generating the outline design ...................................................................................... 2
Chapter 29 Setting the Embroidery Frame Range ....................................................................... 2
Chapter 30 Manual of Embcom Software.................................................................................... 2
30-1 Soft Installation............................................................................................................ 2

30-2 Soft Uninstall ............................................................................................................... 2
30-3 Run and Use the Embcom software............................................................................. 2
30-4 Communication Operation of Embroidery Machine ................................................... 2
Chapter 31 Table of the Machine Parameters .............................................................................. 2
Chapter 32 D Type Sequin Embroidery....................................................................................... 2
32-1 Brief introduction on sequin embroidery..................................................................... 2

32-2 Embroider Sequin ........................................................................................................ 2
32-3 Sequin Design Editing ................................................................................................. 2
32-4 Parameter Setting of Multi-sequin Embroidery........................................................... 2
32-5 Setting sequin mode when adjusting color-changing order......................................... 2
32-6 Manual Operate Sequin Embroidery ........................................................................... 2
32-7 Debugging multi-sequin embroidery ........................................................................... 2
32-8 Sequin mending ........................................................................................................... 2
Chapter 33 Management of Coiling, Taping and Zigzag Embroidery......................................... 2
BECS-316/366 Computerized Embroidery Machine’s Manual V

INDEX
33-1 Function Introduction .................................................................................................. 2

33-2 Main Technique Indexes.............................................................................................. 2
33-3 Manual Operation of the Special Embroidery head, and the Embroidery Parameters
Settings (Attention: the M axis can only be operated with the first needle position.). 2
33-4 Mechanical Category and Driving Mode Choice of Special Embroidery Machines .. 2
AppendixⅠ：Rules for Using USB Disk .......................................................................... 2
AppendixⅡ：All Functions in Different Modes ............................................................... 2
AppendixⅢ：Making of Special Multi-Sequin Design .................................................... 2
All rights reserved. Beijing XING DAHAO Computer Control Equipment Co., Ltd.
VI BECS-316/366 Computerized Embroidery Machine’s Manual

Chapter1 General Descriptions
Chapter 1 General Descriptions

Thanks for using the Computerized Embroidery Control System of DAHAO
Company. It is appreciated that you do read this manual carefully in order to
operate the machine correctly and effectively. Besides, you should keep this
manual for future use.
1-1 Warnings and Cautions
Notice
During the operation, do not try to open the machine box. The high voltage
Danger contained in some parts can be deadliness. Rotating parts may cause serious
injury.
Forbidding Don't expose the machine to humidity gas, poisonous gas, water, and dust.
Don’t restore or operate in vibration, which may cause trouble to the

Forbidding
machine.
Notice Please abide all the warnings and safety requirements to save life.
LCD belongs to fragile goods. Do not use hard materials to click on the
Notice
screen.
Before plugging in, please make sure if the lamp of floppy disk driver is on,
Notice
don't move out the floppy disk..
We will add appendix if necessary, if there is any difference between the
Notice
manual and appendix, subject to the appendix.
In Transportation
Notice Don't hold the cable when moving..
Notice Please abide all the warnings and safety requirements to save life.
Overloading may cause serious loss. Please load according to the

Force
instruction on the box..
Installation
Don't jam the vent on the device. Don’t plug up the machine, or it may set
Notice
fire.
BECS-316/366 Computerized Embroidery Machine’s Manual 1

Capter1 General Descriptions
Notice Make sure the installation direction is correct..
Notice Don't expose the machine to humidity gas, poisonous gas, water, and dust.
Cable Connection
Forbidding Don't test the insulation of the circuit loop.
Forbidding Never try to connect overloaded electronic device on the connector.
Notice Make sure the insulating of the cable is fine.
Notice Communicating cable and power cable should be separated.
All the cables should be well fixed. Don’t put any strength on cables. Make
Notice sure the turning point of cable is well protected. Add pipes to increase
insulating capability.
Machine should be grounded. The resistance should be no larger than 10
Notice
Ω.
Operation direction
Danger Don't operating the machine when there is any damage on the surface..
Forbidding When machine is running, do not touch any running part.
Make sure the configuration of power supply in normal. Use stabilized

Notice
voltage power supply when the voltage rebound is between -10%~10%.
In case of warning, please check out the problem. Operation can only be
Notice
carried out again when problem is solved.
The power supply has over-currency protection function. There is a 3 mins
Notice
time lag before the function can be used again.
Maintenance
If you need to open the machine cover, cut out the power supply first. Duo
Warning to the capacitance after power off, operator must wait one minute till he can
open the machine cover.
Circuit boards can be damaged by static. Non-professional technician can
Notice
not disassemble circuit boards.
2 BECS-316/366 Computerized Embroidery Machine’s Manual

If machine is inactive for a while, users must power on the machine

Notice
regularly (once in 2 or 3 days, more than an hour for each time).
If machine is inactive for a long time, users should have the machine
Notice
checked before power on.
Rejection
Rejection should obey the rules and regulations set by national industrial
Notice
electronic standards.
1-2 Main Features
1. Adjusting Speed
The main shaft speed can be changed manually, or be changed automatically with the
length of stitches during embroidering.
2. Stepping Precision
The minimum of stepping precision is 0.1 mm.
3. Trimming
The machine can trim thread by pressing keyboard manually, or do it automatically during
color-change or at the end of embroidering.
4. Thread Break Detect
During embroidering, the machine will automatically stop and light the red lamp if the
thread is broken or is run out of.
5. Stitch Range
The stitch range is 0.1 mm- 12.7 mm.
6. Color-change Function
While processing one color-change stitch, the machine can change color manually, or
change color automatically according the preset color line.
1-3 Main Functions
1. Display of Chinese, English and Spanish, display of Chinese, English and Turkish,
display of Chinese, English and French, display of Chinese, English and Portuguese or Korean,
English and Spanish.
User can select the software displayed in the Chinese, English, Spanish, Turkish, French,
Portuguese or Korean according to his actual needs via the key board. With the figure on the
keys, the systems is friendly to speakers of different languages.

Capter1 General Descriptions
2. Design Storage Capacity

The system memory can store 2000,000 stitches, which can be extended for user's order.
3. Maximum of Memory Design Count
The maximum is 200（For the various models, the pattern capacity will be different）.
4. Input pattern with Disk or U-disk
User can upload the patterns in various formats into the memory via the U-disk or the
external USB Floppy driver. This product is able to read the patterns in formats of Tajima
binary system, Tajima ternary system, Barudan FDR system (including binary system, ternary
system and Z system) and ZSK system.
5. Output pattern with Disk or U-disk
The patterns in memory can be downloaded to the Floppy Disk and the U-disk. This
product uses the Tajima binary system as the output format. The highlight of it is to use
internet to transmit pattern (Some patterns in other format is unable to be transmit directly.)
6. Repetition Embroidery
The machine can increase embroidery productivity by repetition embroidery. And it can
do embroidery directly in the way of usual repetition, but in the way of partial repetition, the
computer must first compile the ready-for-embroidery design to one normal design and the
machine then embroider the compiled normal design.
7. Cyclic Embroidery
The machine also can increase embroidery productivity by preset cyclic embroidery, by
which the machine automatically starts another same embroidery when one embroidery is
finished.
8. Combining Design
A new design can be formed by combining several normal designs at different size ratio,
rotation angle, figure direction and relative distance, which is called combined design and has a
extension name of PAR. It can be embroidered in one time.
9. Compiling Design
A. Compiling the ready-for-embroider design
After selecting a normal design and presetting the parameters (such as size ration, rotation
angle, figure direction, repetition), the computer can compile the ready-for-embroider design to
a new normal design.

B. Compiling the combined design

Also, one combined design can be compiled to a new normal design.
10. Editing the Normal Design
A normal design can be edit stitch by stitch (or by several amounts of continuous stitches)
in full screen.
11. Patching Embroidering
This function can set a patch code after the color code or stop code, and when the machine
embroiders the patch code, it will halt and move frame out for patching. After stick a patch,
user would pull the operation bar to let the frame move back and continue embroidering.
12. Adjusting the Brake
For various machines, this function can make the machines stop correctly, which means
that the main shaft stops at 100 degree.
13. Save and store the origin point of design
This function can save and store the start embroidering point of each design, instead of
repeating moving frame manually to find the design origin when selecting the same design.
14. Mechanical maintaining and testing
This function is to easily judge the malfunctions when maintaining and testing, which
consists of computer testing, encoder testing, main shaft speed testing, machine parts testing
and the main shaft stops at any position, etc.
15. Some and store the embroidery parameters
This function is to combine the design with selected embroidery parameters such as color
sequence, design direction, rotation angle and repetition, etc. to reduce the times of inputting
parameters when embroider the design without changing the parameters.
16. The software version of the BECS-316/366 can be upgraded by use USB disk. See
Appendix I for detailed operating rules.

Chapter 2 Names of Parts about Electrical Control System
2-1 Operation Control Panel
Operation Control Panel is as following:
BECS-316 Operation Control Panel

23 22
21
1 20
19
18
17
16
15
2 3 4 5 6 7 8 9 10 11 12 13 14
BECS-366 Operation Control Panel

Number Name Description

Displays every operation.BECS-316 type
1 LCD machine use 10.4 inch true color LCD, but
BECS-366 use 8.4 inch.
Press this key to enter into design manage
window, including embroider design, input
design to memory, show design, generate
Design management & Disk
2 design, etc.
management
Press turn page key in design manage window
to enter disk management, including operations
of floppy disk and USB.
3 Reserved Functions Unused Temporarily
Assistant embroidery Design origin, needle stops down, offset point,
4
operation sequin, special embroidery, etc.
Press the key to cut embroidery status between
5 Switch Embroidery status normal embroidery, high speed idling and low
high speed idling.
Press the key to cut manual color-changing
Switch color-changing mode
6 between manual start, auto color-changing
and starting mode status
manual start and auto color-changing auto start.
Press the key to enter into change-color
7 Change color operation
operation.
Press this key to shift the design direction
8 Change design direction
among 8 directions.
After stopping, press this key to select to trim
9 Trimming
upper or lower thread.
When the machine stops, press it, the frame will
10 Go to start point automatically return to the start point of the
current design.
When the machine stops, press the key “Manual
Frame-moving” to move the frame (e.g. in case
11 Go to stop point of patching). Then press this key and the frame
will automatically return to the stop point of the
current design.
12 Exit To exit certain operations.
13 Change embroidery status
14 Confirm To confirm certain operations.
In operation the direction of frame-moving is
the same as the direction key. The combination
15 Manual Frame Moving of directions is supported, namely pressing the
nearby 2 direction keys will move the frame in
the 45 degree between the two directions.
Speed Shift of Manual Press this key to switch the frame-moving
16
Frame-moving speed between high speed and low speed.
Push the button to reduce the embroidering
17 Speed adjust or turn page
speed or turn next page.

Number Name Description

Push the button to increase the embroidering
18 Speed adjust or turn page
speed or turn up page.
It is used for editing design or input needle
19
number.
It is used for selecting menu or setting
20 Digital key
parameter.
Press the key to display embroidery
21 Embroidery information
information.
22 Help key Press the key to display the help.
23 +/- shift To show plus & minus of inputted number.
Note: If the machinery has the function of quilt sewing, LCD will display the length of quilt
sewing on the upper-right side of the screen. As in the following image:
2-2 Operation Bar and Turn Shaft Button
1. Operation bar (embroidery bar under the table)

Stop status: pull the bar right to begin embroidery (including idle running in high or low
speed) and pull the bar left to return (including idle running in high or low speed)
Running status: pull the bar right to the end to embroider slowly and release to normal
speed and pull the bar left to stop embroidery.
2. Turn Shaft Button(over the operation bar case, on the right under the table)
To press the button to make the main shaft rotate one cycle and stop at 100°.
2-3 Darning Switch
1. Thread Break Detecting Device of 3 place

There is a switch on every head of machine. When the switch is up, this head is in normal
embroidering mode and when it is in the middle, this head is in darning mode and when it is
down this head is in stop mode.
2. Thread Break Detecting Device of 2 place
On every head of the machine, there is a darning switch, and it can be move with hand to
the up, middle or down position, but it is stop only at the middle or down position. When the
switch is pushed to up position, it can not stay at up position, and the lamp is red, which hints
that this head is in darning mode. In addition, while thread breaking during embroidering, the
lamp is automatically changed into red and this head is in darning mode. When the switch is at
middle position, this head is in darning mode if the lamp is red, or this head is in normal
embroidering mode if the lamp is green. When the switch is pushed to down position, the lamp
is off, which hints that this head is in stop mode. When the switch is pushed to middle position
from down position, the lamp will be green and the head is in normal embroidering mode.

Chapter 3 How to Start Embroidery
3-1 Summary
3-1-1 System's Working Statuses

The working statuses of computer embroidery machine can be divided into 3 statuses:
1. Preparation status:
Features: machine stops and the icon " "
2. Embroidery confirmation status:
Features: machine stops, and the icon " " appears.

3. Embroidery running status
Features: machine is running, and the

icons " " do animation show.
How to Switch among the above work statuses?

1. In preparation status, after selecting pre-embroidery design and setting the parameters,
first press " " key, and then press " " key, now the machine is in embroidery confirmation
status. Finally, pull the embroidery bar to right to embroider, which means the machine is in
embroidery running status.
2. In embroidery running status, pull the bar left to stop, now the machine is in
embroidery confirmation status (Again, pull the bar right, the machine goes into embroidery
running status).
3. In embroidery confirmation status, first press " " key, and then press " " key to
release embroidery confirmation status, now the machine goes into preparation status.
3-1-2 Descriptions of the Icons of the Embroidery Information
On the right of LCD on main picture, the computer shows the embroidery information as
following figuration:

17 19
21
20
18
16
15
14
13
12
11
1 2 3 4 5 6 7 8 9 10
1. : The machine is in embroidery confirmation status.
: The machine is in preparation status.
2. : The machine is in auto-color and auto-start mode.
: The machine is in auto-color and manual-start mode.
: The machine is in manual-color mode.
3. : The machine is in normal embroidery status.
: The machine is in high-speed idling.
: The machine is in low-speed idling.
4. : Manual frame-shifting is in high-speed.
: Manual frame-shifting is in low-speed.
5. : The machine stops correctly (the main shaft is at 100 degree). : The machine
stops wrong.
: The animation indicates that the machine is running.

: The machine is embroidering the jump stitch.
6. : These 8 icons display embroidery direction of design.
7. : The embroidery design does not repeat in X or Y directions.
: The embroidery design repeats in X or Y directions.
8. : The machine is set cyclic embroidery. : The machine is not set cyclic
embroidery.
9. : The thread is broken.
: The machine finishes embroidering the design.
: The machine is changing color (which means changing needle).
: The user pulls the bar and the machine stops.
10. Display of the running mode
Plain embroidery
Cording embroidery
Boring embroidery
Sequin embroidery
Left coiling embroidery
Right coiling embroidery
Taping embroidery 1
Taping embroidery 2

Z1 embroidery
Z2 embroidery。
Z3 embroidery
Z4 embroidery
Z5 embroidery
Z6 embroidery
Among them, left coiling, right coiling, taping 1, taping 2, Z1, Z2, Z3, Z4, Z5 and Z6
embroideries have to be with the first needle position.
11. The anticipated working time and the working progress

12. The free memory
13. The finished stitches and the frame position

14. The design’s stitch covering area and the last stitch coordinates
15. The color-change number of embroidery design

16. In the confirmation status, the stitch number of the current design is shown .
17. In the embroidery confirmation status, the number of embroidery design is shown.
18. These data is the Automatic Color-change Sequence (or Color Line).
19. This number is the needle number.
20. : The icon indicates that the machine now has an offset point; No sign means that the
machine does not have the offset point.
21. This value is the shaft speed.

Descriptions of Menu Item's Status
The user interface of computer has a lot of menus, which display the ways of keyboard
operation. Usually, one number will be displayed at the front of menu item, which is the serial
number of the menu item.

If the number is replaced by "⊗", the menu item can not be entered. (The parameter
cannot be set or is not functional in the current setting.) If a menu item has a “ ” before it, a
password is needed to enter it.
3-1-3 How to Embroider for the First Time?
The machine embroiders according to the design in store. Before a new machine is used
normally for the first time, the computer should initialize the parameters (See 12-7). Then, all
designs in memory should be cleared (See Chapter 13). Again, input the desired design to
memory store. After that, you can select a design in memory and confirm to embroider design.
Now, the machine goes into embroidery confirm status. Finally, pull the embroidery bar to the
right to start embroidering the design.
3-2 Input a Design into Memory from Floppy Disk
Reading disk design into memory can be performed both in the management of "Disk
Management" and "Design Management".
Operation 1: (by the management of "Disk Management")
1.Press " " key (in embroidery preparation status), the computer shows as following:
DESIGN MANAGEMENT
①SELECT DESIGN FOR EMB.
②SHOW MEMORY DESIGN
③DISK INPUT
④COPY
⑤EDIT
⑥DELETE
⑦DIVIDE
⑧COMBINE
⑨PACKED DESIGN
⑩CLEAR ALL
ARROW OR NUMBER:MOVE, ENTER:CONFIRM
2.Press “ ”to turn page and enter disk management menu.

3.Press " "、" " or digital key"2" to move the cursor to "INPUT", and then press " "
key.

DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT(DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M
⑦INSTALL LETTER LIBS
⑧DELETE LETTER LIBS
⑨DESIGN A LETTER PATTERN
⑩INPUT DESIGN FROM PC
4.The LCD will display the file name in floppy disk, and go on according to the prompt.
5.Select a disk design and press " " key.
6.The number of the design, which needs the least memory and is suggested to use,
appears on the bottom of the screen. Press the key " " to confirm the use of it, and the
machine begins to input. Otherwise you can select a desired design by the digital keys. During
the process the mistakenly input number can be deleted by pressing the key “ ”. Press the
key " " to confirm the design. When the input design is not compatible to an existent one,
the machine will refuse to accept it and you can the key " " to begin a new input.
7.The display shows a prompt “to expand satin”. Please choose “Yes” or ”No” by the key
“ ”, and then press the key " ".
8.When you choose “Yes”, the compensation value has to be input.
9.The design begins to be input from the disk to the system memory, and the management
ends.
Operation 2: (by the management of "Design Management")
1.In the embroidery preparation status press " " key, and the computer shows as follows

DESIGN MANAGEMENT
③DISK INPUT
④COPY
⑤EDIT
⑥DELETE
⑦DIVIDE
⑧COMBINE
⑨PACKED DESIGN
⑩CLEAR ALL
2.Press " "、" " or digital key"3" to move the cursor to "DISK INPUT", and then press
" " key.
DESIGN MANAGEMENT
③DISK INPUT
④COPY
⑤EDIT
⑥DELETE
⑦DIVIDE
⑧COMBINE
⑨PACKED DESIGN
⑩CLEAR ALL
3.Do according to the prompts.

4.Select a design in the disk and press " " key.
5.The number of the design, which needs the least memory and is suggested to use,
appears on the bottom of the screen. Press the key " " to confirm the use of it, and the
machine begins to input. Otherwise you can select a desired design by the digital keys. During
the process the mistakenly input number can be deleted by pressing the key “ ”. Press the
key " " to confirm the design. When the input design is not compatible to an existent one,
the machine will refuse to accept it and you can press the key " " to begin a new input.
6.The display shows a prompt “to expand satin”. Please choose “Yes” or ”No” by the key
“ ”, and then press the key " ".
7. When you choose “Yes”, the compensation values have to be input..

3-3 Preparation before Embroidering
Setting the contents below should be finished or confirmed before embroidering in

embroidery preparation status. Such as: (1) automatic color-change or manual color-change,
which is to change color automatically when there is color-change code during embroidering or
to change color manually after machine stops. (2) automatic start or manual start, which is to
start automatically or manually after automatic color-change, and if it is automatic
color-change, the color line should be set. (3) besides, it is necessary to set figure direction( see
Chapter 6), the rotation angle of figure, size ratio and number of repeating embroidery.( see
Chapter 12).
3-4 Select a Design for Embroidery and Confirm to Embroider the Design
1. Descriptions of Saving and Restoring Design’s Origin Point

(1) The meaning of saving and restoring design’s origin point
That means save the origin point of a design so that leave you away from repositioning
when embroidering the same designs (there may be other design to embroider among them).
(2) The precondition of saving and restoring design’s origin point
The function can be realized until the machine’s zero point (or frame zero point) is set and
is available (the setting method is shown in Section 12-4 ).
(3) The main points must be explained and noticed.
Point 1: when selecting design, there will be a prompt “NO ZERO POINT, CANNOT
SAVE ORIGIN” if you have not set the machine’s zero point, then, please set, and the function
can be realized (see section 12-4 to know how to set the machine’s zero point.)
Point 2: when selecting design, if there is a “*” behind the design number (that means the
design has been saved), and if the current position is not accordant with the position been saved,
then there will be a prompt: “PRESS [HOME] TO RESTORE ORIGIN”, and the design’s
origin point can be recovered. There isn’t the prompt in other case.
Point 3: we suggest you do as the following sequence if you use the function of saving
and restoring the design’s origin point: first, select one design, then, move the frame to find the
design’s origin point, and at last, confirm to embroider, save and store the design’s origin point
according to the prompt.
Point 4: the design’s origin point that has been found by moving the frame after
embroidering confirmation will not be saved and stored.

Point 5: If the design’s origin point has been saved and stored, it can be helpful to the
power resume function. When power off and the frame has been moved, and when the design’s
origin point is available (if not available, set the machine’s zero point again and ensure that it is
same as before), release embroidery confirmation status and select the same design and recover
the design’s origin point, then confirm to embroider, and do high-speed idling to the stop point,
finally continue embroidering.
2. Explanations about saving and storing embroidery parameters.
When confirming to embroider a design, the machine can save and store the design
parameters for later use. The parameters are: design direction, angle of rotation, X scale, Y
scale, priority mode, repetition mode, repetition times, frequency of X repetition, frequency of
Y repetition, X repetition distance, Y repetition distance and color-change sequence (can
store/recover the first 100 color numbers).
If the design parameters of a design have been saved, then when selecting the same design,
it can recover the design parameters automatically.
This function is very applicable when embroidering the same design repetitiously without
changing the design parameters, so that it can reduce the times of inputting parameters and
reduce the operation mistakes.
3. Select a design for embroidery
Operation:
(1) Press " " key (in embroidery preparation status), the computer shows as following:
DESIGN MANAGEMENT
③DISK INPUT
④COPY
⑤EDIT
⑥DELETE
⑦DIVIDE
⑧COMBINE
⑨PACKED DESIGN
⑩CLEAR ALL
(2) The cursor is at "SELECT DESIGN FOR EMB.", and press " " key.
(3) LCD displays the memory designs, and automatically display the figure of design at

which the cursor is. If the count of designs is more than 10 , you can use " "、" " key to
turn to other pages.
(4) According to the prompt, press " "、" " to move the cursor to select one design,
and press " " key.
(5) If the computer has saved the set parameters of this design and the current parameters
are different from them, the prompt is "RESTORE PARAMETERS?", and you can select
"YES" or "NO" with " "、" " keys and " " key to decide whether the computer restore
the saved parameters.
(6) Press " " key to select the design for embroidering, or other key to give up this
operation.
(7) After selecting the design for embroidering, the computer will prompts: “PRESS
[HOME] KEY TO RESTORE ORIGIN” if the origin point of this design has saved into the
computer, users can press “ ” key to move the frame to the saved origin point, or press other
keys to escape.
4. Confirm to embroider a design
Operation:
(1) Press " " key, the computer shows as following:
(2) Press " " key to confirm embroidery, or press other key to escape.
(3) If the design origin point is not saved or the saved origin point is not the same with

the frame position, the computer will prompts: “PRESS [HOME] KEY TO SAVE ORIGIN”,
users can press “ ” key to save the origin point, or press other keys to escape.
(4) If the computer has not saved the set parameters of this design or the saved
parameters are different from current parameters, the prompt is "SAVE PARAMETERS?", and
you can select "YES" or "NO" with " "、" " keys and " " key to decide whether the
computer save the current parameters.
(5) In the main picture, the icon " " appears and the machine enters into the
embroidery confirmation status. Now, you can pull the bar to start embroidery.
3-5 Normal Embroidering, Returning and Darning Embroidering
In embroidery confirmation status (the icon " " appears), push the darning switch of
machine head that will perform normal embroidery to go to the normal embroidering mode,
and push the darning switch of machine head that will not embroider to go to the darning mode,
and then pull the operation bar to right and release it to let the machine start normal embroidery.
(when you pull the bar right and don't release it , the machine will embroider in lower speed.)
During embroidering, pull the bar left, the machine will stop.
After the machine stops, pull the operation bar to left and the frame will return to its last
position along original path. Pull the bar one time, the frame return one needle step. Pull the
bar continuously and the frame will return one needle step after another continuously. After the
frame return 10 needle steps continuously, the frame can return continuously even when you
release the bar.( This may be different according to different machine types). When the frame
return continuously, release the bar and pull it left again, the frame will stop returning.
The aim of returning is usually to perform darning embroidery. After the returning stops,
push the darning switch of machine head that will perform darning embroidery to go to the
darning mode, and then pull the operation bar to right and the machine head will start darning
embroidery while other heads don't. When the frame goes to the point where the frame begins
to return, other heads whose darning switches are in normal embroidering mode will start to
embroider.
3-6 Release Embroidery Confirmation Status
You should release embroidery confirmation status when you want to embroider other
designs after finishing embroidering one design or to revise size ratio, rotating angle, the
repetition, figure direction, or to do the management of "Disk Management" and "Design

Management".
Operation:
(1) Press “ ” key, the computer shows as following:
(2) Press " " key to release embroidery confirmation status according to the prompt (or
press other keys to abandon), and then enter into the embroidery preparation status (the icon
" " blinks.).

Chapter 4 Normal Embroidery and Idling
4-1 Relations between Normal Embroidery and Idling
Functions as idling, returning, etc. are intended for the convenience of darning.
Low-speed idling, high-speed idling or positioning idling can be used in the light of different
positions. In the states of idling, the returning also cover low-speed idling returning,
high-speed idling returning and positioning idling returning.
4-2 Low-speed Idling
Operation: Press " " key when machine stops until the following display appears:
The icon " " appears.
After setting low-speed idling, the main shaft remains inactive when pulling bar for
normal embroidery, but the frame runs forward along the stitch trace. When pulling bar for
returning, the main shaft keeps inactive, but the frame returns along the stitch trace.
4-3 High-speed Idling

After setting high-speed idling, the main shaft and frame remain inactive, the count
increases based on a unit of 100 stitches. After pulling the bar for halting, the frame moves
directly to the actual position of the current count. When pulling bar for returning, the main
shaft and frame keep inactive, but the count decreases. After pulling the bar for halting, the
frame returns directly to the actual position of the current count.
4-4 Release of Low-speed/High-speed Idling
The icon
" " appears.
This is the state of normal embroidery.

4-5 Positioning Idling
The positioning idling can make the frame directly runs forwards (or backwards) to an
assigned counting position, or to a latest color-change position, or even to a latest stop-code
position.
Operation:
(1) Press " " key (in embroidery confirm state), the menu appears as following:
【OTHER MANAGEMENT】
⊗SET DESIGN PARAS 1 ①HI-SPEED DESIGN 2
②FRAME TO POINT(OPTIONAL) ②COMPILE PACKED DESIGN
③DESIGN RANGES’S OPERATIONS ③COMPILE EMBROIDER. DESIGN
④OFFSET→OFF ⊗FRAME TO MAKE DESIGN
⑤SET POWER RESUME ⊗ADD PATCH CODE TO DESIGN
⑥POWER RESUME ⊗COMPENSATION
⑦SET MACHINE PARAS ⊗TO MAKE TRUE DESIGN RANGE
⊗PARA OF SEQUIN,SPECIAL EMB,AFC ⑧TO SET ALL HEADS PATCH→N
⑨中文/ENGLISH/SPANISH ⑨LET NEEDLE DOWN AND MOVE FRAME
⑩TO SET CYCLIC EMB.→OFF ⑩NO OUTPUTTING DESIGN→OFF
⊗PRE-DISPLAY THE DESIGN→N 3 ① SET DATE & TIME 4

②LCD COLORS (FOR MANAGER)
③SELECT SHOWING COLORS
④SET EMB. FRAME RANGE
⊗MACHINE SELF-TEST
⑥TEST ENCODER
⑦TEST MAIN SHAFT SPEED
⑧TEST MACHINE PARTS
⑨ROTATE SHAFT FROM 100 TO ANY
⑩UPDATE THE SOFTWARE
ARROW OR NUMBER: MOVE, ENTER: CONFIRM
(2) Press " "、" " or digital key "2" to move the cursor to "FRAME TO POINT
(OPTIONAL)", and then press " " key. The positioning idling menu displays as following:
OTHER MANAGEMENT
①FORWARD STI.
②BACKWARD STI.
③NEXT COLOR
④LAST COLOR
⑤NEXT STOP
⑥LAST STOP
(3) Press " "、" " key to select the desired positioning idling, and then press " "

key.
(4) Continue the operation for different positioning idling according to the prompts
respectively.
(5) The computer automatically exits to the main picture, which is as following:
(6) The user can pull the bar to finish the positioning idling.
(7) Finally, the user can press “ ” key to let the computer to go to normal embroidery
status.

Chapter 5 Color-change Management
5-1 Manual Needle-change (Color-change) when Stop
Press the digital key to carry out manual color-change when the machine stops.
5-2 Manual Color-change and Manual Start during Embroidering
To set manual color-change and manual start, the user just presses " " key until the
main picture is as following.
If the machine is set into manual color-change and manual start, manually perform the
color-change and select the first needle position before starting embroidering operation, then
pull bar to start embroidery.
When the color-change code is processing during embroidering operation, the machine
will halt automatically and the icon " " appears for manual color-change. At the moment,
the operator should press the digital key to carry out manual color-change. After the required
needle position having been set, pull the operation bar to start embroidery (manual start).
5-3 Automatic Color-change and Manual Start (or Automatic Start) during
Embroidery
To set automatic color-change and manual start, press " " key until the main picture is
as following.

To set automatic color-change and automatic start, press " " key until the main picture
is as following.
If the machine is set into automatic color-change, the color-change sequence (or be called
color line) should be set in advance before the embroidery confirmation status.
When pulling the operation bar to start embroidery, the computer will carry out
color-change according to the needle position set in the color line (excluding the condition that
the current needle position conforms to the needle position set in the color line), then start
embroidering.

When the color-change code appears during embroidering, the machine will automatically
halt and change to the assigned needle position according to the needle number set in the color
line. In case of setting as automatic start, the machine will automatically continue embroidering,
whereas setting as manual starting, the operator must pull the operation bar to start
embroidering.
If the machine set as automatic color-change and automatic start and an over-frame
operation (set in the design file) follows the current color-change, the machine will perform the
two actions at the same time.
5-4 Setting Automatic Color-change Sequence (or Color Line)
The automatic color-change sequence is intended for the machine that has been set as
automatic color-change, and offers automatic color-change sequence.
Note: the times of changing color is 250 at most.
Operation:
1. Press " " key, then appears:
①Input & Repeat

②Modify
③Replace
④Setting Method
2. If press “1” and " " key, then input color line, for example: 1,2,3,and " ". All after
that the color line will repeat like this: 1,2,3,1,2,3,1,2,3…
3. If press “2” and " " key, then you can move the cursor to modify the needle selected
individually. Press [enter] to end.
4. If press “3” and " " key, then you can modify the color line in whole by switching
the needle number.
5. (Only available in special model)Sequin setting: If press “4”and " " key, then appears:

①method 0：Large
②method 1：Small
③method 2：Large
④method 3：Small
⑤method 4：Large
⑥method 5：Small
⑦method 6：Large
⑧method 7：Large
（1） Press “ ” key, follow the prompt “ ” or “ ” key to select large or small
（sequin design）, press “ ” key, then appears:
①method 0：Large End

②method 1：Small
③method 2：Large
④method 3：Small
⑤method 4：Large
⑥method 5：Small
⑦method 6：Large
⑧method 7：Large
（2）Press " " or " "to select （Include：“A”、“B”、“C”、“D”、“AB”、“AC”、“AD”、

“BC”、“BD”、“CD”、“ABC”、“ABD”、“ACD”、“BCD”、 “ABCD” etc.）, then press “ ”key,
system prompts to input a number for the method, then press“ ”key. System will prompt to
change another method. Operation is as same as above. Select to end setting the method.
6. (Only available in special model)When you decide the order of color changing，you can
select stitch position and different methods. Operation is as following:
(1) Press “ ” key, then it appears:

①Input & Repeat
②Modify
③Replace
④Setting Method

(2) The icon stays at①, press “ ”key, then press the digital numbers one by one. When
you input the stitch position (for example, you select the 1st position for sequin embroidery),
the screen will display like:
00123456
Method：0
(3) Press “ ” or “ ”to select the set method of step（2）, then press “ ”. System
prompts to input the next color-change position, then press the digital numbers one by one,
then press the color changing position, press “ ” or “ ” to finish.

5-5 Storing the Manual Color-change Number into Color Line
In embroidery confirmation status, if the machine carries out manual color-change, the
computer will store the manual color-change number into color line or not according the
setting of "STORE MANUAL-COLOR". It functions as following: A) During embroidering, if
one number in color line is wrong, you can execute the manual color-change, and then the
computer will automatically store the correct number into color line. B) If you embroider a new
design first time and you can not decide the color line, you can set the color line using the
setting of " STORE MANUAL-COLOR ".
After finishing embroidering a design, the machine automatically change the setting of
“STORE MANUAL-COLOR” to “No”.
Operation:
(1) Press " " key, the menu appears as following:


⑥TEST ENCODER
(2) Press " "、" " or digital key "7" to move the cursor to "SET MACHINE PARAS",
and then press " " key.
(3) The system displays as following:
【 SET MACHINE PARAS】

①FRAME CURVE＆ANGLE: F4/250 1 ①T.B. DETECT WHEN JUMP: N 2
②T.B. DETECT: Y ②JUMP＆TRIM: 3
③STOP AFTER T.B. DETECT: Y ③JUMP STITCH SPEED: 500
④PRESS KEY AFTER T.B.: N ④LOCK STICH WHEN TRIM: Y
⑤T.B. BACK STI.: 0 ⑤LOCK NUM. AFTER TRIM: 3
⑥PATCH COUNT: 2 ⑥LENGTH OF LOCK STI: 1.0
⑦ACTION AFTER PATCHING: SLOW ⑦START FOR SAME COLORS: Y
⑧STI. NOT T.B. DETECT: 8 ⑧STORE MANUAL-COLOR: N
⑨AUTO ORIGIN: Y ⑨SEWING EMPTY STITCH: N
⑩INITIALIZE SYSTEM!: ⑩VALUE FOR THICK CLOTH: 0
MAX. SPEED: 700 3 ①SPEED AFTER TRIM: 80 4

②MIN. SPEED: 250 ②SPEED WHEN TRIMMING: 80
③SHIFT LENGTH: 5.0 ③HOOK ANGLE BY MOTOR: +0
④TURN OFF TRIMMING: N ④HOOK RATIO BY MOTOR: 1:10
⑤TRIM MODE: 3 NEEDLES: 4
⑥ACTION AFTER TRIM: Y ⑥SET BRAKE PARA.: 5
⑦FRAME AFTER TRIM: N ⑦MAIN MOTOR PARA.: 0
CHECK TRIM IS OK: Y ⑧SET RUN SPEED: 80
⑨ROUNDS FOR BRAKE: 1 ⑨STARTUP STITCHES: 8
⑩STITCHES AFTER TRIM: 2 ⑩STARTUP ACCE: 15
(4) Press " "、" " or digital key "9" to move the cursor to "STORE
MANUAL-COLOR ", and then press " " key.
(5) Press " "、" " key to select "Y" or "N".
(6) Press " " key.

5-6 The Color-change Speed
The color-change speed can be adjusted for the specific machine, which execute the
color-change operation by stepping motor. The speed adjusting is for meeting the need of
different mechanical characteristic.

⑥TEST ENCODER
(3) Press " " key twice to turn to page 3, which is as following:

①SPEED OF SLOW EMB.: 80 5 ①OVERFRAME BY STEP: N 6
②COLOR-CHANGE SPEED: 12 ②SPEEDWHEN OVERFRAME: 16
③ADJUST HEAD SOLENOID: 0 ③HIGH FRAMING SPEED: 16
④PARA. OF NEEDLE DOWN: 15 ④LOW FRAMING SPEED: 12
⑤RATIO OF AC INDUCTION: +0 ⑤STOP TO COLR: N
⑥DIP1: 0 ⑥BORING NEEDLE: N
⑦DIP2: 0 ⑦BORING EMB. DISP.(mm): 0
⑧DIP3: 0 ⑧CORD EMB. NEEDLE: N
⑨DIP4: 0 ⑨SPEED FOR CORD EMB.: 400
⑩DISPLAY STI. OR NOT: Y ⑩STOP OK bef. PULL BAR: Y
①ADJ. STARTUP HOLDING: 0 7 8

DETECT T.B. MODE: 1
③STI. FOR FILTER T.B: 3
④SLOW STI. AFTER PATCH: 0
⑤SPEED AFTER PATCH: 700

(4) Press " "、" " or digital key "9" to move the cursor to "COLOR-CHANGE
SPEED", and press " " key.
(5) Press " "、" " key to select the data, and greater data represents higher speed.
(6) Press " " key.

Chapter 6 Setting Design Direction
Chapter 6 Setting Design Direction
Before embroidery confirmation, you can set the design direction for embroidering.
When the display of design direction is “P”, the design embroidering direction is identical to its
original direction. Take the embroidering of letter “F” as an example to explain the relations
between the embroidered design and the design direction:
Operation:
In embroidery preparation status, press " " key to change the design direction until the
desired direction is selected.
The icon will be changed.

Chapter 7 Frame Management
7-1 Manual Frame Shifting
Press eight direction keys: “ ”、“ ”、“ ”、“ ”... to make the frame shift in eight
different directions respectively. The “ ” key is the speed-switching key of frame shifting.
The frame-shifting speed is divided into high-speed and low-speed. When pressing the “ ”
key, the speed is changed.
7-2 Returning to Origin Point
With this function, the frame can return back to the position before manual frame shifting.
When machine stops halfway or embroidering finished, the frame can return back to the
starting point of design with this function.
Operation:
A. Press " " key, the menu frame appears as follows:
①BACK TO ORIGIN
②RESTORE ORIGIN
③SAVE ORIGIN
④AUTO SET ORIGIN
⑤FRAME TO BORDER
⑥RETURN TO ORIGIN
B. Press " " key to confirm the operation, or press “ ” key to quit.
7-3 Restore Design’s Origin Point
If the origin point of this design has been saved into the computer, this function could
restore the saved origin point for embroidering the design.
Operation:
①BACK TO ORIGIN
②RESTORE ORIGIN
③SAVE ORIGIN
④AUTO SET ORIGIN
⑤FRAME TO BORDER
⑥RETURN TO ORIGIN

B. Press “ " or "2" key to move the cursor to " RESTORE ORIGIN", and then press
" " key to continue.
C. The computer will prompts: “PRESS [HOME] KEY TO RESTORE ORIGIN”, and
you can press “ ” to move the frame to the saved origin point. Otherwise, press any other
key.
7-4 Save Design’s Origin Point
This function could save the origin point for the design.
Operation:
①BACK TO ORIGIN
②RESTORE ORIGIN
③SAVE ORIGIN
④AUTO SET ORIGIN
⑤FRAME TO BORDER
⑥RETURN TO ORIGIN
B. Press “ " or "3" key to move the cursor to " SAVE ORIGIN", and then press " "
key to continue.
C. The computer will prompts: “PRESS [HOME] KEY TO SAVE ORIGIN”, and you
can press “ ” to save the origin point. Otherwise, press any other key.
Note: If the origin stays unchanged, then you only need to “SAVE ORIGIN” once, then
you can “RESTORE ORIGIN” at any time you want.
7-5 Automatically Set the Origin Point
Based on the function of “Setting the Embroidery Frame Range” (For details, see the
relative sections of the Owner’s Manual), this function would calculate the origin point for the
selected design, and move the frame to the new origin point, which will make the design at the
center of frame.
Operation:

①BACK TO ORIGIN
②RESTORE ORIGIN
③SAVE ORIGIN
④AUTO SET ORIGIN
⑤FRAME TO BORDER
⑥RETURN TO ORIGIN
B. Press “ " or "4" key to move the cursor to " AUTO SET ORIGIN", and then press
" " key to continue.
C. The computer will prompts: “PRESS ENTER TO CONTINUE”, and you can press
" " key to move frame to the new origin point, which let the design at the center of frame.
Otherwise, press any other key.
D. Attentions: This function doesn’t do the function of “Save Design’s Origin Point”, in
case of clearing the last origin.
7-6 Moving Frame along the Border
After selecting the design but before starting embroidery, the frame will run along the
periphery for checking whether it exceeds the limits.
Operation:
①BACK TO ORIGIN
②RESTORE ORIGIN
③SAVE ORIGIN
④AUTO SET ORIGIN
⑤FRAME TO BORDER
⑥RETURN TO ORIGIN
B. Press “ " or "5" key to move the cursor to " FRAME TO BORDER", and then
press " " key to continue.
C. The computer will prompts: “FRAME ALONG DESIGN RANGE!”, and you can
press " " key to move frame along the border. Otherwise, press any other key.
7-7 Returning to Origin
This function is used in quilt sewing. The operator can prevent the cloth from moving by
letting the needle dowm, then roll the cloth to keep on embroidering.

Operation:
(1) Press “ ” key, following image appears:
①BACK TO ORIGIN
②RESTORE ORIGIN
③SAVE ORIGIN
④AUTO SET ORIGIN
⑤FRAME TO BORDER
⑥RETURN TO ORIGIN
(2) Press “ ” or digital “6” key, move the cursor to “RETURN TO ORIGIN”, then
press " " key.
(3) Prompt shows “PRESS ENTER!”, then press " " key to returning to the origin
point or press other key to escape.
7-8 Returning to the Stop-embroidery Point
After halting in the halfway of embroidering operation, press the manual frame-shifting
key to shift the frame out (for darning). After the completion of darning, this function can make
the frame return to the stop-embroidery point.
Operation:
(1) Press the manual frame-shifting key to shift the frame out (for darning).
(2) Press " " key, the main picture appears like this:

(3) Press " " key to confirm the operation, or press other key to quit.

Chapter 8 Embroidery Speed(Main Shaft Speed)
Chapter 8 Embroidery Speed (Main Shaft Speed)
In the process of embroidery, the main shaft speed of the embroidery machine will change
by computer according to the stitch length of design. The low speed is intended for long stitch
embroidery, whereas high speed for short stitch. However, users can set the limit speed, what is
called “SETTING LIMIT SPEED”. The highest embroidery speed can increase or decrease
within the limit speed.
The limit speed ranges from 250 rpm to 1000 rpm. User can select the limit speed and do
not need superabundance. For example: in normal using is 850rpm, then set in 850rpm.
8-1 Setting the Limit Speed
This setting specifies the limit value for the highest embroidery speed.
Operation:

⑥TEST ENCODER
(3) Press " " key to go to page 2, which is as following:

Chapter 8 Embroidery Speed (Main Shaft Speed)


(4) Press " "、" " or digital key "2" to move the cursor to "MAX. SPEED", and press
" " key.
(5) Press " " to end the operation.
(6) Press " " to go to the main picture.
NOTE: The factory default value is recommended for the limit speed.
8-2 Setting Embroidering Speed
It specifies the running speed during embroidering operation.

Operation:
(1) Press " " key. When pressing once the key, the speed will raise 10 rpm. When
having been reached the limit speed, the speed will not raise any more.
(2) Press " " key. When pressing once the key, the speed will reduce 10 rpm.
When reducing to 250 rpm, the speed will not reduce any more.

Chapter 9 Trimming Thread
Chapter 9 Trimming Thread
9-1 Automatic Trimming Thread
When operation such as color changing, frame jumping, etc. are required in embroidery,
as well as at the end of embroidering, the machine can trim thread automatically.
9-2 Manual Trimming Thread
This function can be executed by pressing several keys.

Operation:
(1) Press " " key, the main picture appears as following:
(2) Press " " key to trim thread, or press other key to quit.

Chapter 10 Disk Management
Note: The pattern operations mentioned herein are mainly to the U-disk. If you are the user
of floppy disk, please buy the USB Floppy driver, an optional part.
10-1 Directory Listing of Disk
This operation is able to view the design stored in disk, as well as file name, file length
and free space of disk.
Operation:
(1) Insert the design disk into floppy disk driver, and press " " key to enter the design
management menu, then press “ ”to turn page and enter disk management menu appears as
following:
DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT(DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M
(2) The cursor will be at "DISK DIR", press" " key.

(3) The LCD will display the file in floppy disk. If the file count is greater than 10, you
can press " "or " " key to turn to other pages.
(4) Press " "、" " key to select the design, and press " " or " " key to view it.
During the viewing, you can press " " or " " key to vary the display speed. Press " " to
end the display.
(5) Press " " or " " key to quit the disk operation.
10-2 Input Design from Disk to Memory
Operation:
(1) Insert the design disk, and press " " key to enter the design management menu, then
press “ ”to turn page and enter disk management menu. Press " "、" " key or

digital key "2" to move the cursor at "INPUT", press" " key.
DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT(DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M
(2) Press " "、" " key to select the design (you can press " " key to view it and
press “ ” to end), and press " " key.
(3) At the bottom of LCD, the computer will show the minimum available number of
design (recommended for use). If you use it as the new design number, press " " key to
confirm, and then begins the disk reading operation. If disagreeing to use the design number,
press digital keys to enter the design number you want. In the event of having error in entering
numeral, press " " key to clear it. After entering the design number, press " " key for
setting. When there is any conflict between the entered design number and the design number
existed in memory, the machine will refuse to accept this entry; therefore you should enter
another design number and press " " key. After the design number having been proved to
be correct, then begins to read the design from disk to memory. Upon the completion of
design reading, it will return to the disk management menu.
(4) Press " " or " " key to quit the disk management.
10-3 Output Design from Memory to Disk
It stores the design in memory to disk in a binary format. Coordinating to the use of
“Input Design from Memory to Disk”, this function is able to complete the operation of
copying a design from a disk to another disk.
When the computer has set “NO OUTPUTTING DESIGN” to “Yes”, the operator should
first set it to “No” before he output design from memory to disk. For details, see chapter 25.
Operation:
(1) Insert the design disk, and press " " key to enter the design management menu,

then press “ ”to turn page and enter disk management menu. Press " "、" " key or digital
key "3" to move the cursor at "OUTPUT(DSB)", press" " key.
DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT(DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M
⑨DESIGN A LETTER DESIGN
(2) Press " "、" " key to select the memory design, and press " " key.
(3) Press digital keys to enter the disk file name, press " " key to begin saving the
design into disk (or press " " key to give up the operation). After finishing the save, the disk
management menu appears.
10-4 Deleting the Design in Floppy Disk
Operation:
key "4" to move the cursor at "DEL FILE", press" " key.
DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT(DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M

(2) Press " "、" " key to select the design (you can press " " key to view it), and
press " " key to delete the design or press " " to give up.
10-5 Formatting a 720KB Disk
It carries out formatting of a double density 3.5 inch disk in DOS format.
Operation:
key "5" to move the cursor at "FORMAT 720K", press" " key.
DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT(DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M
(2) Press " " key to format disk (or press " " to give up), after finishing the
operation, the disk management menu will appear.
10-6 Formatting a 1.44MB Disk
It carries out formatting of a high density 3.5 inch disk in DOS format.
Operation:
key "6" to move the cursor at "FORMAT 1.44M", press" " key.

DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT(DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M
(2) Press " " key to format disk (or press " " to give up), after finishing the
operation, the disk management menu will appear.

Chapter 11 Displaying Parameters and Displaying Language Selection
11-1 Viewing the Common Parameters
Operation:
(1) Press " " key, if the pre-embroidery design is normal design, the computer will
show the following figure:
【DISPLAY EMB. INFO.】
DESIGN No.: 12 ROTATE: 0

DESIGN ATT.: NORMAL DESIGN X-SCALE: 100
CURRENT: 0 Y-SCALE: 100
OVERALL: 942108 REP.PRIOR: X PRIOR
X-MOVE: +0.0 REP.MODE: NORMAL REP.
Y-MOVE: -48.2 X-REPS: 1
SPEED: 700 Y-REPS: 1
NEEDLE: 1 X-INTERVAL: +0.0
OFFSET: N Y-INTERVAL: +0.0
ZERO POINT: Y PRIOR MODE: ROTATE PRIOR
C KEY: CLEAR, OTHER KEY: EXIT
(2) If the pre-embroidery design is packed design, the computer will show the following
figure:

【DISPLAY EMB. INFO.】
DESIGN No.: 88
DESIGN ATT.: PACKED DESIGN
CURRENT: 0
OVERALL: 942108
X-MOVE: +0.0
Y-MOVE: -48.2
SPEED: 700
NEEDLE: 1
OFFSET: N
ZERO POINT: Y
C KEY: CLEAR, OTHER KEY: EXIT
11-2 Clearing Accumulated Stitch Count and X/Y Displacement
Operation:
(1) Press " " key, the computer will show the common parameters on LCD.
(2) Press " " key to clear "Overall Stitch Count" and "X/Y Move".
11-3 Switching of Display Language
The BECS-316/366 use the Chinese, English and Spanish interfaces and so on.
Operation:
(1) Press " " key, the menu appears as following(in Chinese display):

【辅助管理】
⊗设定放大、旋转及反复 1 ①生成高速花样 2
②定位空走 ②从组合花样生成基本花样
③花样周边操作 ③从刺绣参数生成基本花样
④另外起点设置→未设 ⊗移框生成花样
⑤断电框保护设置/设绣框原点 ⊗花样增加贴布绣功能
⑥断电框保护恢复 ⊗内存花样平包针补偿
⑦设定机器参数 ⊗普通花样产生轮廓花样
⊗设定金片绣、特种绣、气框绣参数 ⑧设置是否所有机头补绣→否
⑨中文/ENGLISH/SPANISH ⑨针停下位后移框
⑩设置循环绣开或关→关 ⑩禁止花样输出→关
⊗是否刺绣前预显花样→否 3 ①设置系统时钟 4
②选择屏幕颜色（维修人员使用）
③选择花样显示颜色
④刺绣范围的软件设置
⊗机器自检（用于维修）
⑥编码器自检（用于维修）
⑦主轴转速自检（用于维修）
⑧机器部件测试
⑨转动主轴从 100°到一定角度
⑩从磁盘升级机器软件
上下键或数字键移动光标，回车选择菜单
(2) Press " "、" " or digital key "9" to move the cursor to "中文/English/Spanish",
and then press " " key. The LCD displays the next language.
If the displaying language is the last, the LCD will display the first. That is say the machine
has the circular function on displaying language.

Chapter 12 Other management and Setting the Parameters
12-1 Setting of Magnification, Rotation and Repetition
This operation is able to set the magnification factor (50% ~ 200%), angle of rotation (0° ~
89°) of a design, as well as repetition if necessary in embroidery.
Operation: (in embroidery preparation status)

①SET DESIGN PARAS 1 ①HI-SPEED DESIGN 2
⊗FRAME TO POINT(OPTIONAL) ②COMPILE PACKED DESIGN
⊗OFFSET→OFF ④FRAME TO MAKE DESIGN
⑤SET POWER RESUME ⑤ADD PATCH CODE TO DESIGN
⑦SET MACHINE PARAS ⑦TO MAKE TRUE DESIGN RANGE
①PRE-DISPLAY THE DESIGN→N 3 ① SET DATE & TIME 4

⑥TEST ENCODER
(2) The cursor will be at "SET DESIGN PARAS", and press " " key to enter the next
menu as following:
SET DESIGN PARAS

①ROTATE: 0
②X-SCALE: 100
③Y-SCALE: 100
④REP.PRIOR: X PRIOR
⑤REP.MODE: NORMAL REP.
⑥X-REPS: 1
⑦Y-REPS: 1
⑧X-INTERVAL: +0.0
⑨Y-INTERVAL: +0.0
⑩PRIOR MODE: ROTATE PRIOR

(3) Press " ", " " and " " key to select the following parameters for revising them:
① Angle of rotation (0° ~ 89°)
Use digital key, " " and " " keys to input data. This angle is an angle at which a
design rotating counterclockwise according to the selected design direction.
② X magnification (50% ~ 200%)
Use digital key, " " and " " keys to input data. This magnification is a transverse
magnification of a design.
③ Y magnification
Use digital key, " " and " " keys to input data. This magnification is a longitudinal
magnification of a design.
④ Repetition sequence (X priority or Y priority)
Use " ", " " and " " keys to perform the inputting. X priority presents the
repetitive embroidery line by line in transverse direction during repetition. Y priority presents
the repetitive embroidery row by row in longitudinal direction.
⑤ Repetition mode
Use " ", " " and " " keys to perform the inputting. Usual repetition refers to the
embroidering operation that after a complete design having been embroidered, the same design
will be embroidered in the next position, i.e. the repetitive embroidery is performed by a
complete design after another. Partial repetition refers to the embroidering operation that
after a design having been embroidered with stitches of one color, the embroidery will be
continued in the corresponding position of the next design with the same color stitches until
this color repetition is completed, and then the embroidering operation will repeat with another
color stitches until the repetitive embroidery is made with all color-stitches, i.e. the completion
of the repetition of a complete design is based on the repetition of each part.
For partial repetition, you must compile the pre-embroidering design into a normal design,
and embroider the normal design. (See Chapter 17)
⑥ Frequency of X repetition (1 ~ 99)
Use digital key, " " and " " keys to input data. The frequency of X repetition presents
the number of transversal repetition, i.e. the frequency of repetitive embroidery in a line.
⑦ Frequency of Y repetition (1 ~ 99)
Use digital key, " " and " " keys to input data. The frequency of Y repetition presents

the number of longitudinal repetition, i.e. the frequency of repetitive embroidery in a row.
⑧ X repetition distance (unit: mm)
Use digital key, " ", " " and " " keys to input data. X repetition distance presents
the distance between the starting points of two adjacent designs in transverse direction during
repetition (accuracy: 0.1mm).
⑨ Y repetition distance (unit: mm)
Use digital key, " ", " " and " " keys to input data. Y repetition distance presents
the distance between the starting points of two adjacent designs in longitudinal direction during
repetition (accuracy: 0.1mm).
⑩ Priority modes (magnification priority or rotation priority)
Use " ", " " and " " keys to perform the inputting. When selecting X magnification
dissimilar to Y magnification and with rotating angle, the magnification priority and rotation
priority can give different embroidery results.
(4) Press " " or " " key to end setting the parameters.
(5) Press " " or " " key to go to the main picture.
12-2 Operation of Design Periphery
Operation:

⑥TEST ENCODER
(2) Press " ", " " key or digital "3" to move the cursor to "DESIGN RANGE'S

OPERATIONS", and press " " key to enter the next menu as following:
OTHER MANAGEMENT
①SHOW RANGE
②MOVE FRAME ALONG RANGE
③GENERATE DESIGN OF RANGE
④FRAME, THEN EMB.
⑤EMB. ONE CROSS
⑥EMB. RIGHT ANGLE
⑦EMB. DESIGN QUADRATE RANGE
⑧EMB. DESIGN TRUE RANGE
(3) According to the prompt, press " ", " " and " " keys to complete the following
operation:
① Showing periphery
After selecting design but before starting embroidery, check the peripheral range of the
design.
② Moving frame along the periphery
After selecting the design but before starting embroidery, the frame will run a cycle along
the periphery for checking whether it exceeds the limits.
③ Generating a new periphery design
This operation can be carried out after selecting the design but before starting embroidery,
which can produce a peripheral design of the current design. The peripheral design can be
embroidered separately.
In case user’s embroidering periphery can be achieved by embroidering the peripheral
design, and the peripheral design has a central “+” line, if the length of the central “+” line is
insufficient, the No. 99 design can be used for supplementary embroidery.
④ Move frame and embroider back along the path
Operation: move the frame along the assigned paths from the current position, when meet
a inflexion, press " " key to confirm the line path; then repeat the above operation to finish
the whole paths, you can also quit to the main picture by pressing “ESC” key; finally, you can
pull the bar directly to start embroidering, the machine will embroider along the trace in
converse direction to current position, and return to the “preparation status” automatically.

⑤ Embroider one cross at current position

Operation: input the length of the cross (unit: mm), then the system will return to the main
picture automatically. You can pull the bar directly to start embroidering and the machine will
embroider a “+” at current position, and return to the “preparation status” automatically.
⑥ Embroider right angle at current position
Operation: first, input the length of X-direction (unit: mm. If it is positive, then embroider
along X-direction, if it is negative, embroider along the X negative direction); second, input the
length of Y-direction (unit: mm. If it is positive, then embroider along Y-direction, if it is
negative, embroider along Y negative direction), then the system will back to the main picture
automatically; finally, you can pull the bar directly to start embroidering and the machine will
embroider a right angle at current position, and, return to the “preparation status”
automatically.
⑦ Embroider design’s quadrate range
Operation: the system will create a quadrate design and return to the main picture
automatically; you can pull the bar directly to start embroidering and the machine will
embroider the quadrate range at current position, and return to the “preparation status”
automatically.
⑧ Embroider design’s true range
Operation: the system will create a figure design similar to the current design and return to
the main picture automatically; you can pull the bar directly to start embroidering and the
machine will embroider the figure at current position, and return to the “preparation status”
automatically.
(4) Press " " or " " key to end the operation of design periphery.
(5) Press " " or " " key to go to the main picture.
12-3 Setting the Offset Point
What is called offset point can be an arbitrary point beyond the starting point of the design
as shown in the following figure:

a: offset point, b: starting point
When you select a design and make the machine enter into the embroidery confirmation
status, the system will clear the offset point. Operation for setting offset point and
embroidering is as following:
(1) Select a design for embroidering and make the machine enter into embroidery
confirmation status. (See Section 3-4)
(2) Press " ", " ", " " and " " to move the frame to the starting point of design.

⑥TEST ENCODER
(4) Press " ", " " key or digital "4" to move the cursor to "OFFSET", and then press
" " key.
(5) Press " ", " ", " " and " " to move the frame to the offset point. In case of
needs not to set offset point or wants to deleting offset point that has been set previously, go to
the following step without moving the frame to the offset point.

(6) Press " " key to continue, and the computer go to the main picture.
This flag shows

that the computer
has offset point.
(7) The frame first moves from the offset point to the start point, and then begins
embroidering. Moreover, setting the offset point is also the base of frame moving out in
patching embroidery.
12-4 Setting Frame Protection when Power Off (Setting the Machine’s Zero
Point)
The purposes of the operation are:

Purpose 1: The function of “setting the protection when power off/frame zero point” can
restore the frame position when power off unexpectedly together with the function of power
resume.
Purpose 2: The function of “setting the protection when power off/frame zero point” is to
set the base point when a design’s origin point needs to be saved and restored. This base point
is recommended to be any point on the bedplate, once being set, you’d better not change it and
should marks flag.
Note:
Note 1: The realization of purpose 1 is based on the available limit switch and setting
frame zero point automatically.
Note 2: The operation of “setting frame zero point automatically” or “Setting frame zero
point manually” all can set the base of saving and restoring the design’s origin point.

Note 3: The operation of this function can only be done with one of two operations of
“setting frame zero point automatically” and “Setting frame zero point manually”.
Note 4: Except for particular instance, during embroidering by normal operation, whether
handy frame origin memory or auto frame origin memory, one time correct setup is ok.
1. Setting frame zero point manually
Note: when meeting emergency stop because of malfunctions or something unusual such
as power off unexpectedly, etc. the machine will cancel the “setting frame origin” function to
avoid the mistakes. So, at that time, you should do operation of “Setting frame zero point
manually” again at the last frame zero point.
If the frame has been moved after power off, or if power on again after maintenance, you
should do again the operation of “Setting frame zero point manually”.
Operation:
(1) Press " " key, the menu appears as follows:

⑥TEST ENCODER
(2) Press " ", " " keys or numeric key "5" to move the cursor to "SET POWER
RESUME/ZERO POINT", and press " " key.
(3) If the function of “setting emb. frame range” has been set, then there will be a
warning: “AUTO CLEAR ‘EMB. FRAME RANGE’”, and press " " key to continue.
(4) The prompt is “MANUALLY ‘SET ZERO’ POINT?”, then select “YES” with " ",
" " keys, and press " " key.

(5) Do as prompting, mark the frame zero point when the frame has been moved to the
selected zero point, then finish the setting by pressing " " key.
2. Setting frame zero point automatically
Note: please ensure that the limit switch is available before this operation, or the frame
will be damaged.
Operation:

⑥TEST ENCODER
(2) Press " ", " " keys or numeric key "5" to move the cursor to " SET POWER
RESUME/ZERO POINT ", and press " " key.
(3) If the function of “setting emb. frame range” has been set, then there will be a
warning: “AUTO CLEAR ‘EMB. FRAME RANGE’”, and press " " key to continue.
(4) The prompts is “MANUALLY ‘SET ZERO’ POINT?”, then select “NO” with
" ", " " keys, and press " " key.
(5) The machine will give a prompt “TO SET POWER RESUME”, and press " " key,
then the frame begin moving, when meets the limit switch, the frame will return to the zero
point. The setting then finished.
12-5 Frame Restoring after Power Off
In case of frame having been moved after power off, this operation can be used to restore
the frame position before power off when the power is on again. The proper performance of

this operation is based on the “SET POWER RESUME/ZERO POINT”. In addition, if the
power is off in the process of embroidering operation and the frame has not been shifted, you
also can directly pull the operation bar to continue embroidering after power is on again.
It will be invalid if the operation of “setting frame zero point manually” is done.
Operation:
(1) Turn the main shaft to the stopping position at 100 degrees

⑥TEST ENCODER
(3) Press " ", " " key or numeric key "6" to move the cursor to "POWER RESUME",
and press " " key.
(4) Continue the operation according to the prompt, and the restoration of frame position
can be achieved.
(5) The main picture will automatically appear after it.
12-6 Demanding whether Setup Frame Zero Point or not
Press " " key to check whether machine setup frame ZERO POINT or not: the machine
will be displayed as “ZERO POINT: √” if ZERO POINT setup, otherwise the machine will
be displayed as “ZERO POINT: ×”.
Setting frame zero point has two ways: auto ways and manual ways.
1. After auto setting frame zero point, if it is correct, then the icon “⊗” before“POWER

RESUME” in the “OTHER MANAGEMENT” will be changed into “⑥”.

2. If manually setting frame zero point, the icon “⊗” before“POWER RESUME” in the
“OTHER MANAGEMENT” will be not changed, and it still be “⊗”.
12-7 Setting the Machine Parameters
Operation:

⑥TEST ENCODER
(3) The machine parameters are in 5 pages (you can press " " or " " key to turn to
other pages), which are as following figures. The parameters can be revised using " ", " ",
digital keys, " " and " " keys.




①SPEED OF SLOW EMB.: 80 5 ①OVERFRAME BY STEP: N 6
②COLOR-CHANGE SPEED: 12 ②SPEEDWHEN OVERFRAME: 16
③ADJUST HEAD SOLENOID: 0 ③HIGH FRAMING SPEED: 16
④PARA. OF NEEDLE DOWN: 15 ④LOW FRAMING SPEED: 12
⑤RATIO OF AC INDUCTION: +0 ⑤STOP TO COLR: N
⑥DIP1: 0 ⑥BORING NEEDLE: N
⑦DIP2: 0 ⑦BORING EMB. DISP.(mm): 0
⑧DIP3: 0 ⑧CORD EMB. NEEDLE: N
⑨DIP4: 0 ⑨SPEED FOR CORD EMB.: 400
⑩DISPLAY STI. OR NOT: Y ⑩(AFC) Use: Y
①ADJ. STARTUP HOLDING: 0 7 8

②DETECT T.B. MODE: 1
③STI. FOR FILTER T.B.: 3
④SLOW STI. AFTER PATCH: 0
⑤SPEED AFTER PATCH: 700
(4) Press " " to end the operation.

(5) Press " " to go to the main picture.
Note: For details, see Chapter 31 about "Table of the Machine Parameters".
12-8 Setting Parameters of Sequin, Special Emb, etc
Operation:

⑧PARA OF SEQUIN,SPECIAL EMB,AFC ⑧TO SET ALL HEADS PATCH→N

⑥TEST ENCODER
(2) Press " "、" " or digital key "8" to move the cursor to "PARA OF
SEQUIN,SPECIAL EMB,AFC", and then press " " key.
(3) According to machine prompts, press " ", " ", digital keys, " ",“ ”,“ ”
and " " keys to set all the parameters. Parameters in the table below are all adjustable, but
they vary according to different types.
SEQUIN R ON/OFF Y 1 ①SEQUIN OFF AFTER T.B. N 2
SEQUIN L ON/OFF Y ②MODE OF SEQUIN ON/OFF 0
③SPEED FOR SEQUIN R 400 SPECIAL HEAD INTERVAL 250
④SPEED FOR SEQUIN L 400 ④ZIG SWING ANGLE 0
⑤SEQUIN R ADJ. ANGLE +0 ⑤CLAMP FOOT DISPLACE 0
⑥SEQUIN L ADJ. ANGLE +0 ⑥RATIO OF COIL EMB. 1
⑦SEQUIN R TYPE ⑦M AXIS STOP TO ORIGIN Y
⑧SEQUIN L TYPE ⑧ROD POS. OF ZIG LEFT
⑨AUTO START FOR SEQUIN N ⑨SPEC. EMB. TRIM BOT N
⑩TIME OF SEQUIN ACTION 3 ⑩FRAME SWING FOR ZIG +0.2
①M AXIS BACK TO ROTATE Y 3 ①(AFC) USE N 4

②SPEC. EMB. MIN SPEED 250 ②(AFC) INTERVAL TIME 3
③SPEC. SPEED-DOWN ANGLE 30
④SPEC. SPEED-DOWN RATIO 2
⑤M AXIS ORIGIN AT T.B. Y
⑥Z SHAFT CONTROL ANGLE 180
⑦ADJ. CLAMP FOOT LIMIT 0
⑧ADJ. ZIG ROD ANGLE 1
⑨ROTARY GAP OF M AXIS 0
⑩M AXIS WORK-OFF ANGLE 0

(4) Press " "or " " to exit from “PARA OF SEQUIN, SPECIAL EMB, AFC.”.
(5) Press " "or " " to go to the main picture.
Note: For information about setting parameters, see Chapter 31 for more information.
12-9 Compensating of Satin Stitches
This operation is able to search automatically the satin stitches of the assigned design and
carry out compensation as required, thus obtaining a widening or narrowing result of satin
stitches. After compensating of satin stitches, a new design will be created but the source
design keeps unchanged.
Operation: (in embroidery preparation status)
⑥POWER RESUME ⑥COMPENSATION
①PRE-DISPLAY THE DESIGN→N 3 ①SET DATE & TIME 4

⑥TEST ENCODER
(2) Press " "、" " or digital key "8" to move the cursor to "COMPENSATION", and
then press " " key.

(3) Select the source design according to the prompt.
(4) Input the X and Y compensation value, which ranges from -0.2 mm to +0.3 mm.
(5) Input the number of destination design and press the key " ".
(6) Wait until the new design is made.
(7) Press “ ” or " " to go to the main picture.

(8) During the input design process, the compensated design can be input to the

memory directly by the help of prompts.
12-10 Set Date & Time

This operation can set date and time for screen display.
Operation:
(1) Press the key “ ”, then press “ ” to turn to page 3 to enter “OTHER
MANAGEMENT” menu:
①PRE-DISPLAY THE DESIGN→N 3 ①SET DATE & TIME 4

⑤MACHINE SELF-TEST
⑥TEST ENCODER
(2) Use " " and " " to select “”, then press " " key to display the follow image:
2006：09：20 16：20：40
2006
UP/DOWN KEY TO SET TIME
(3) Press " " and " " to select a year and then press the key “ ”.

(4) Then system prompts to set the month. Repeat step (3) until finish all the settings,
then press the key “ ”. After the system turns back to “OTHER MANAGEMENT”
automatically, the system clock will show the updated time.
(5) Press “ ” to exit from “OTHER MANAGEMENT”.

Chapter 13 Management of Design in Memory
Note: For BECS-316/366, the design management must be done in the embroidery
preparation status.
13-1 Select a Design for Embroidery
This function selects a design for the preparation-embroidering design. See 3-4 for details.
13-2 List the Design in Memory
This operation lets the operator able to view the design stored in memory, the design
count, free memory, and also display the design information, such as color-change times, stitch
count, X range, Y range.
Operation:
(1) Press " " key, the computer shows the design management menu as following:
DESIGN MANAGEMENT
③DISK INPUT
④COPY
⑤EDIT
⑥DELETE
⑦DIVIDE
⑧COMBINE
⑨PACKED DESIGN
⑩CLEAR ALL
ARROW:MOVE, ENTER:CONFIRM
(2) Press " "、" " or digital key"2" to move the cursor to "SHOW MEMORY
DESIGN", and then press " " key.
(3) Directory of design in memory is listed on screen and the design at the cursor is
displayed automatically. In case of the directory exceeding one page, use " " or " " key
for viewing.

SELECTING A DESIGN
01 MEM 9182
02 MEM 1078
99 MEM 68
COUNT： 3
FREE STITCHES： 497920
(4) Press " "、" " key to move cursor, and press " " key to view the design in
detail.
(5) Now, you can view the design according to the prompt.
(6) Press " " to end viewing.
13-3 Input a Design into Memory from Floppy Disk
This operation is similar to “DISK INPUT”. See 3-2 for details.

13-4 Copy the Design
Operation:
DESIGN MANAGEMENT
③DISK INPUT
④COPY
⑤EDIT
⑥DELETE
⑦DIVIDE
⑧COMBINE
⑨PACKED DESIGN
⑩CLEAR ALL
(2) Press " "、" " or digital key"4" to move the cursor to "COPY ", and then press
" " key.
(3) Press " "、" ", " " and " "key to select the source design, and then press
" " key to go to next step or press " " key to quit.

(4) According to the prompt, input the number of destination design, and press " " key
to begin the copying.
(5) Press " " or " " to end the design management.
13-5 Delete the Design
It deletes a design in the memory.

Operation:
DESIGN MANAGEMENT
③DISK INPUT
④COPY
⑤EDIT
⑥DELETE
⑦DIVIDE
⑧COMBINE
⑨PACKED DESIGN
⑩CLEAR ALL
(2) Press " "、" " or digital key"6" to move the cursor to "DELETE", and then press
" " key.
(3) Press " "、" ", " " and " "key to select the design, and then press " " key
to go to next step or press " " key to quit.
(4) After the computer deletes the design, it will go to the design management menu.
13-6 Divide the Design
This operation is intended for dividing the design in memory into two new designs and
keeping the source design in memory unchanged.
Operation:

DESIGN MANAGEMENT
③DISK INPUT
④COPY
⑤EDIT
⑥DELETE
⑦DIVIDE
⑧COMBINE
⑨PACKED DESIGN
⑩CLEAR ALL
(2) Press " "、" " or digital key"7" to move the cursor to "DIVIDE", and then press
" " key.
(3) Press " "、" ", " " and " "key to select the source design, and then press
" " key to go to next step or press " " key to quit.
(4) After the prompt, input a stitch count (the first divided design has the stitches of the
count number).
(5) Input the number of first divided design.
(6) Input the number of second divided design.
(7) The computer does the dividing, and then will go to the design management menu.
13-7 Splice two Designs
Operation:
DESIGN MANAGEMENT
③DISK INPUT
④COPY
⑤EDIT
⑥DELETE
⑦DIVIDE
⑧COMBINE
⑨PACKED DESIGN
⑩CLEAR ALL

(2) Press " "、" " or digital key"8" to move the cursor to "COMBINE", and then
press " " key.
(3) Press " "、" ", " " and " "key to select the first source design, and then press
" " key.
(4) Press " "、" ", " " and " "key to select the second source design, and then
press " " key.
(5) According to the prompt, input the distance between the end stitch of first design and
the beginning stitch of second design.
(6) Input the number of destination design.
(7) The computer does the splicing, and then will go to the design management menu.
13-8 Editing the Packed Design
The packed design means a design group packed from several (less than 100) normal
designs in memory after setting parameters, which is intended for continuous embroidery
automatically.
Operation:
DESIGN MANAGEMENT
③DISK INPUT
④COPY
⑤EDIT
⑥DELETE
⑦DIVIDE
⑧COMBINE
⑨PACKED DESIGN
⑩CLEAR ALL
(2) Press " "、" " or digital key"9" to move the cursor to "PACKED DESIGN", and
then press " " key.
(3) The lower side of screen prompts you to enter the number of packed design. Input
“0” for abandoning editing operation, or input a non-existent number of design for creating a

packed design, or input an existent packed design for editing it. Whereas input a number of
existent normal design in memory, then you must repeat the input.
(4) Enter into the menu of editing packed design:
SERIES: 1
①DESIGN No: 0
②DIRECTION: P
③ROTATE: 0
④X-SCALE: 100
⑤Y-SCALE: 100
PAGE:OTHERS, ESC:RETURN
You must input the following parameters for each packing normal design: number of
design in memory, design direction, angle of rotation, X magnification, Y magnification, X
distance relative to the first design and Y distance relative to the first design.
Pressing " " and " " key, you can set several designs. After completion, press " "
key to store the packed design and return to the design management. Or press " " key and
decide whether you save the packed design, then return to the design management.
(6) As for selecting a design，system can show the image of a normal design with an
extension “MEM” but not that of a combined design with an extension “PAR”. If you want to
view the image of a combined design, you should go to the menu “OTHER MANAGEMENT”
and operate “FROM PACKED DESIGN TO NORMAL DESIGN” to create a normal design
with an extension “MEM” so as to view.
13-9 Clear All Designs in Memory
This operation is intended for clearing all designs in memory, be careful to use it!
Operation:

DESIGN MANAGEMENT
③DISK INPUT
④COPY
⑤EDIT
⑥DELETE
⑦DIVIDE
⑧COMBINE
⑨PACKED DESIGN
⑩CLEAR ALL
(2) Press " "、" " or digital key"0" to move the cursor to "CLEAR ALL", and then
press " " key.
(3) The lower side of screen prompts you to check whether or not you clear all designs.
Press " "、" " keys to change [YES] or [NO]. Select [YES] and press " " key to clear
all designs. If select [NO] and press " " key or press " " key to give up the operation.
(4) After clearing all the designs, system will display the memory size (total stitches
remained). Press any key to return to the menu of “DESIGN MANAGEMENT”.

Chapter 14 Edit of the Design in Memory
Adopting the most convenient, direct-viewing and full-screen editing mode, the function
of editing design in memory has more advantages, such as: easy editing, flexible, faultless.
This function is able to directly carry out edit of the design with stitch count of less than
65 thousand. For the oversize design, indirect edit can be made. As for the oversize design, it
is recommended to divide the design into several sub-designs (the sub-designs to be edited
have stitch count of less than 65 thousand) which will then be edited respectively, and finally
several sub-designs are spliced in order. Owing to the oversize designs appear seldom,
therefore the contradiction between editing speed and editing oversize design will be solved
easily.
14-1 Entering the Edit of Design in Memory
Operation:
DESIGN MANAGEMENT
③DISK INPUT
④COPY
⑤EDIT
⑥DELETE
⑦DIVIDE
⑧COMBINE
⑨PACKED DESIGN
⑩CLEAR ALL
(2) Press " "、" " or digital key"5" to move the cursor to "EDIT", and then press
" " key.
(3) The lower side of screen prompts: "EDIT NEW DESIGN?", you can press " "、
" " keys to change [YES] or [NO]. If you select [YES] and press " " key, you should
input the number of new design. If you select [NO] and press " " key, then you can select an
existent normal design for editing.
(4) After editing the design (See the following sections), the design management
appears.

Chapter14 Edit of the Design in Memory
14-2 How to Edit a Stitch
After entering to the function of editing new design, on the top of the screen will display:
0 ＋０＋０
On the bottom of the screen will display the current stitch: “STITCH：１”.
Of which data on a line presents a stitch. The first row is the code of the stitch. Its
code are as following. The second row is the value of X (unit: 0.1 mm) and the third row is
the value of Y (unit: 0.1 mm).
0: invalid stitch
3: satin stitch
4: jumping
5: frame jumping
6: absolute jumping
7: color-change
8: stop
9: towel embroidery
10: chain embroidery
According to the above, the character of stitch and the values of X and Y can be chosen
by pressing digital key directly (If X or Y is negative, press " " key to change into positive
number, then press digital key.), and then press " " key.
When the cursor move to the next line, it shows one stitch has been edited over.
Press " " key continuously, then the screen will display:
0 ＋０＋0
0 ＋0 +0
0 ＋０＋0
0 ＋0 +0
0 ＋０＋0
0 ＋0 +0
… … … …

Input the value you need to the corresponding position in each line, and press " " key.
Then the stitch number displayed on the bottom of the screen is the stitch number has been
edited. After editing press " " key and select "⑤", then press " " key. The new design has
been edited over.
1. Modifying a stitch
You can use " ", " ", " ", " ", " " and " ", " " keys to move the cursor,
and use digital key to input numeral. It is necessary to point out that the range of X and Y
values of stitch length is −127 ~ +127. In case the input value is out of the range, the machine
will not confirm this entry. For instance, when changing “+126” to “+63”, first move the
cursor underneath “+”, then press " ", " " and " " keys.
2. Deleting a stitch
Use " ", " ", " ", and " " keys to move the cursor underneath the stitch to be
deleted, then press " " key to delete the stitch. And the deleted stitch is stored for using it for
inserting a stitch.
3. Inserting a stitch
Use " ", " ", " ", and " " keys to move the cursor underneath a stitch, press " "
key to insert the last deleted stitch before this stitch.
Note: Using function “2” and “3” by turns can speed up input of repeat stitch.
Attention must be paid that when a design requires adding one stitch, inserting a stitch
must be used.
14-3 Rapidly Searching a Stitch
Operation:
(1) Press " " or " " key to enter into the following menu:
PRESS ？KEY TO DO:

①GO TO STI.
②GO TO CODE
③BLOCK
④HELP
⑤SAVE & EXIT
⑥QUIT
(2) Press " "、" " or digital key"1" to move the cursor to "GO TO STI.", and then

press " " key.

(3) Input the stitch number to which the cursor will go.
(4) The cursor will directly go to the stitch.
14-4 Rapidly Searching a Special Stitch
Operation:
PRESS ？KEY TO DO:
①GO TO STI.
②GO TO CODE
③BLOCK
④HELP
⑤SAVE & EXIT
⑥QUIT
(2) Press " "、" " or digital key"2" to move the cursor to "GO TO CODE", and then
press " " key.
(3) Input the code of stitch which the computer will search backwards from the current
stitch.
(4) If finding the code, the cursor will directly go to the stitch with this code.
NOTE: This function only applies to afterward-searching from the current stitch.
14-5 Block Operation
The block means a part of continuous stitches of the design in memory. Its function is
intended for performing rapid operation to these continuous stitches: copying, moving, deleting
and merging several designs in memory.
Operation:
PRESS ？KEY TO DO:
①GO TO STI.
②GO TO CODE
③BLOCK
④HELP
⑤SAVE & EXIT
⑥QUIT
(2) Press " "、" " or digital key"3" to move the cursor to "BLOCK", and then press

" " key.

(3) the block operation menu is as following figure:
PRESS ？KEY TO DO:
①MARK BEGIN
②MARK END
③CANCEL
④COPY
⑤MOVE
⑥DELETE
⑦READ
These functions interpret as following: “MARK BEGIN” is defined as block beginning.

“MARK END” is defined as block end. “COPY” refers to copy the block to the position of
cursor. “MOVE” refers to move the block to the position of cursor. “DELETE” refers to delete
all stitches in the block. “READ” means that the machine will take a design (you first input the
number of design) as a block and read the block at end of editing design.
14-6 Help for Editing
Operation:
PRESS ？KEY TO DO:
①GO TO STI.
②GO TO CODE
③BLOCK
④HELP
⑤SAVE & EXIT
⑥QUIT
(2) Press " "、" " or digital key"4" to move the cursor to "HELP", and then press
" " key.
(3) Display the help relating to “HOW TO EDIT A DESIGN”, press any key to end it.
14-7 Saving the Editing Design and Exit
Operation:

PRESS ？KEY TO DO:

①GO TO STI.
②GO TO CODE
③BLOCK
④HELP
⑤SAVE & EXIT
⑥QUIT
(2) Press " "、" " or digital key"5" to move the cursor to "SAVE & EXIT", and then
press " " key.
(3) The computer begins to save the design, and then exit the editing.
14-8 Quitting the Editing
Operation:
PRESS ？KEY TO DO:
①GO TO STI.
②GO TO CODE
③BLOCK
④HELP
⑤SAVE & EXIT
⑥QUIT
(2) Press " "、" " or digital key "6" to move the cursor to "QUIT", and then press
" " key.
(3) The computer prompts you to save the editing design, and you can select [YES] or
[NO], then press " " key to go to the design management operation.
(4) The computer exits the editing.

Chapter 15 Operation Help
Chapter 15 Operation Help
This function helps users to perform the operation and displays prompting message.
Operation:
(1) At the main picture, press " " key to enter the help-show frames
(2) Press any key to turn to other frames till exit.

Chapter 16 Monogramming and Making a High-speed Design
16-1 monogramming (optional)
If there is a “Disk of Letter Library” with your embroidery machine, you can embroider
any text with 28 fonts at will. In the disk there are 28 kinds of forms of written or printed
characters which 26 capital letters of English alphabet, or 26 small letters of English alphabet,
or digits 0~9. Users can create monograms in horizontal line, vertical line, or three-point arc.
For the first time, users must install the letter library from “Disk of Letter Library” to
memory, which will run out about 200,000 stitches store and can be set free by the operation of
“Deleting the letter library”.
1. Installing the letter library
Operation:
(1) Press " " key to enter the design management menu, then press “ ”to turn page
and enter disk management menu, the following figure appears. Press " "、" " or digital
key "7" to move the cursor to "INSTALL LETTER LIBS", and then press " " key.
DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT(DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M
ARROW OR NUMBER:MOVE, ENTER: CONFIRM
(2) Insert the disk of letter library according to the prompt, and press “ ” key.
(3) Wait for about 4 minutes to copy files.
(4) Do the operation of “Listing the design in memory” (Seeing section 13-2) to check if
the letter library is installed correctly. If so it were, the file count should increase by 56.
Otherwise do the operation of “Deleting letter library” first and then do this operation again.
2. Deleting letter library
Operation:

Chapter 16 Monogramming and Making a High-Speed Design
and enter disk management menu, the following figure appears:

DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT(DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M
(2) Press " "、" " or digital key "8" to move the cursor to "DELETE LETTER LIBS",
(3) Press " " or " " key to select [YES] and press " " key to delete the letter
library.
3. Monogramming
Operation:
and enter disk management menu, the disk management menu shows as follows: (if the letter
library has not installed, then can not input letter design.)
DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT(DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M
⊗DESIGN A LETTER DESIGN
(2) Press " “, “ " or numeric keys to move cursor to set parameters of letter design,
shows as follows, and press " " key to begin. And, the unit of X-scale, Y-scale and satin
stitch density is %, the unit of distance is mm, and the rotation angle: 1 degree. Press " " key

to go on.
①ARRANGE: HORIZONTAL
②CHAR FORM: 1
③X SCALE: 100
④Y SCALE: 100
⑤DENSITY: 100
⑥COLOR: N
⑦X SPACE: +0.0
⑧Y SPACE: +0.0
⑨ANGLE: 0
(3) For “ARC” arrangement, you should input the interrelated parameters, which
include co-ordinates of starting point, middle point and end point. After setting the parameters,
press " " key to go to next step. If not for “ARC” arrangement, then jump to next step.
(4) Input all the characters according to the characters’ code printed on the LCD, and
press “ ” key to go on, or press " " key to exit.
(5) System shows the letter design, and you can adjust the letters about their positions,
forms, angles, scales, etc. Digital keys 1, 3, 5 and 9 stand for positive direction, while 2, 4, 6
and 0 the opposite; Digital keys 7 and 8 are for selecting single numbers. Press " " key to go
on.
(6) System asks “If to create the letter design?” Select [NO] to exit, or select [YES]
to go to next step.
(7) System shows the design. Press " " key to end the show.
(8) System prompts to save the design. Select [NO] to give up, or select [YES] and
press “ ” key to go to next step.
(9) Input a new design number and press “ ” key for saving.
(10) System returns to the “Disk Management” menu.
16-2 Making a High-speed Design
If the stitch length is greater than 7.0mm during embroidering, the main shaft speed will
slow down. And if you hope it does not occur, you can make a high-speed design from the
design and embroider with the high-speed design, which will not make the main shaft slow
down.

Chapter 16 Monogramming and Making a High-Speed Design
Operation:
(1) Press " " key, and then press " " key, then press " " key.

⑥TEST ENCODER
(2) Select the design, and press " " key.

(3) Input the number of the new high-speed design.
(4) The system will create the new high-speed design automatically.
(5) Press the key " " to go to the main picture.
(6) If necessary, embroider the new design.

Chapter 17 Compile the Packed Design and Embroidering Design
17-1 Compile the Packed Design
Operation:
(1) Press " " key, and then press " " key, the menu appears as following:

⑥TEST ENCODER
(2) Press " "、" " or digital key "2" to move the cursor to "COMPILE PACKED
DESIGN", and then press " " key. Select the packed design which extension name is "PAR",
and press " " key.
(3) Press " " key to confirm compiling the packed design, or press other key to exit.
(4) Input the number of new design, and the system will create the new normal design
automatically, which is identical with the packed design.
(5) Press " " key to go to the main picture.
17-2 Compile the Embroidering Design
Operation:
(1) Press " " key, and then press “ ”, “ ” and “ ” to enter the process of
compiling the embroidering design:


⑥TEST ENCODER
(2) Press " " key to confirm compiling the embroidering design, or press other key to
exit.
(3) Input the number of new design, and the system will create the new normal design
automatically, which is identical with the embroidering design having the embroidering
parameters.

Chapter 18 Initialize the System Parameters during Electrifying
Chapter 18 Initialize the System Parameters during Electrifying
If some data in the system is illegal by rare chance, which is caused by outside
interference or by software bugs, the machine may not work after power-on. To solve this
problem, you can initialize the system parameters during electrifying as following:
Operation:
(1) Press and hold " " key, and turn on the power of machine.
(2) The system initializes the system parameters and gives a sound, and release off " "
key, the machine will start working.

Chapter 19 Adding Patch(applique) code to a Design
Chapter 19 Adding Patch Code to a Design
During embroidering, you may want to shift the frame in order to stick a patch
expediently. The ways of shifting frame are: manual frame shifting and auto frame shifting.
Manual frame shifting is done as following: First, the machine automatically stops at a
stitch of stop code while embroidering. Second, shift the frame to the deserved position by
pressing the frame-shifting keys, and stick a patch. Then, press “ ” and “ ” keys, you will
make the frame move to the stop position. Finally, pull the bar to continue embroidering.
Auto frame shifting is done as following: First, add patch code to the design, which is
describe in the next paragraph. Then, select the design and set it into embroidery confirmation
status. Again, set the offset point for this design. Finally, pull the bar and start to embroider.
The machine will pause at a stitch of patch code and automatically shift the frame to the offset
point, which will let you stick a patch expediently. You can pull the bar to continue
embroidering after stick the patch.
The operation of adding patch code to a design is as following:
(1) Press " " key, and then press " " key, the menu appears as following. Press
" "、" " or digital key "5" to move the cursor to "ADD PATCH CODE TO DESIGN", and
then press " " key.

⑥TEST ENCODER
(2) Select the design for being added patch code, and press " " key

Chapter 19 Adding Patch(applique) code to a Design
(3) According to the prompt, you will be asked to add a patch code for each of color
code and stop code, or not do so.

Chapter 20 The Enhanced Funtions of Dot Key
Chapter 20 The Enhanced Functions of Dot Key
Warning: the operation would rotate the main shaft, and the operator should pay
attentions to it.
20-1 Turn the Main Axis at 100 Degree Manually
If necessary, you can turn the main axis and make the main shaft stops at 100 degree by
manually pressing the keys as follows.
Operation:
①TO TURN AXIS ①SEND SEQUIN

②LET NEEDLE DOWN ②READY M AXIS
⊗ V1-4ON OR OFF ③CYCLE M AXIS
⊗ROLL CLOTH ④TURN M AXIS
⑤SET SEQUIN ⑤INC CLAMP FOOT
⑥CANCEL SEQUIN ⑥DEC CLAMP FOOT
B. Press " " key to turn the main axis at 100 degree, or press “ ” key to quit.
20-2 Let the Needle Sew Down and Move the Frame
The function is intended for special sewing. After the needles sewing down, the needles
will fasten the embroidering cloth, and then the operator can loose the cloth from the frame and
move the frame, what is for continuous embroidering in the long cloth.
Operation:


B. Press “ " key to move the cursor to "LET NEEDLE DOWN ", and then press
" " key.
C. There will be a prompt “press ‘enter’ key to confirm”, if you press " " key, then
the needle will go down into the embroidery, please be careful! At this time, you can loose the
embroidery to move the frame. Or, you can press other key to give up.
D. Now, you can move the frame to the desired position. Press " " key to finish.
E. When the operation finished, you should turn the main shaft at 100 degree (Seeing
the last section).
20-3 Switching On/Off of Valves in Quilt Embroidery
This function is for quilt embroidery. The user can open or close the four valves according
to needs.
Operation:

B. Press “ " key to move the cursor to "V1-4 ON/OFF", and then press " " key.
C. Select 1~4 and press" "to open/close the valve.
D. Repeat the above operation to set all the valves..
E. When the operation finished, press“ ”to exit.
20-4 Manual Operation of Sequin Embroidery
This function is only available for the sequin embroidery machines. Operation include
“SET SEQUIN”, “CANCEL SEQUIN” and “SEND SEQUIN”
When the embroidery needle position is on the sequin needle position, the manual

operation of sequin embroidery is as follows:

(1) Press the key “ ”, and the following menu will appear:

③V1-4ON OR OFF ③CYCLE M AXIS
④ROLL CLOTH ④TURN M AXIS
(2) Press the key “ ” to select “ROLL CLOTH” and then press “ ”, a dialogue will
appear:
UP/DOWN
Y：0.0
Use " " and " " to adjust the range of cloth rolling.
(3) Press the key “ ” to exit.
20-5 M Axis Operation of Taping Embroidery
This function is only for machines with taping embroidery function and includes
“READY M AXIS”, “CYCLE M AXIS” and “TURN M AXIS”.
Operation:

(2) Press the “ ” key to select“READY M AXIS”and press“ ”, and the A axis
will rotate to the working point.

(3) Press the “ ” key to select “CYCLE M AXIS” and press“ ”, and the A axis
will rotate to the zero point.
(4) Press t the “ ” key to select “TURN M AXIS” and press“ ”. Then press“ ”
or“ ”to turn the M axis in different directions. Press“ ”to end the operation.
20-6 Operation of Clamp Foot

This function is only available for machines with taping embroidery function. When the
embroidery needle position is on the taping embroidery needle position, the operation is as
follows:

(2) Press the keys “ ” to select “INC CLAMP FOOT” and press “ ”, and the clamp
foot of taping embroidery will increase.
(3) Press the keys “ ” to select “DEC CLAMP FOOT” and press “ ”, and the clamp
foot of taping embroidery will decrease.

Chapter 21 Shift Frame to Make a New Design
Chapter 21 Shift the Frame to Make a New Design
Sometimes, you want to embroider the boundary of a design before embroidering it. The
function of “Shift the Frame to Make a New Design” can create such a design, and you can
select the new design to embroider the boundary.
Operation:
(1) In embroidery preparation status, shift the frame to the starting point of design.
(2) Press " " key, and then press " " key, the menu appears as following:

⑥TEST ENCODER
(3) Press " "、" " or digital key "4" to move the cursor to "FRAME TO MAKE
(4) According to the prompt, enter the maximum stitch length.
(5) Shift the frame along the boundary of deserved design, and press " " key to set the
points which are assembled into the design trace. Meantime, you can press " " key to vary
the stitch code between satin stitch and jump stitch.
(6) Press " " key to end inputting the trace points.
(7) According to the prompt, input the number of new design, and press " " key to
create the new design.

Chapter 22 Setting the Cyclic Embroidering
Chapter 22 Setting the Cyclic Embroidering
When the machine is set into the cyclic embroidering, the computer will make the frame
return to the starting point and the machine will start embroidering the design once again
without pulling the bar after the machine has finished embroidering the design one time.
This setting will increase the productivity of embroidering.
Operation of setting or canceling of the cyclic embroidering:
(1) Press " ", then press digital key "0" to move the cursor to " TO SET CYCLIC
EMB.", and then press " " key.

⑥TEST ENCODER
(2) Press " "、" " or digital key "0" to move the cursor to " TO SET CYCLIC EMB.",
(3) Press " "、" " keys to select “ON” or “OFF”, and press " " key. If the machine
is in the cyclic embroidering, the icon " " will appear. Otherwise, the icon " " will
replace the former icon " ".

Chapter 23 Adjust the Machine’s Braking (For Manufacturer)
Chapter 23 Adjust the Machine's Braking (for Manufacturer)
23-1 Summary
This function is intended for advising the control parameters of machine braking, so let
the machine braking be optimal. The computer provides with one of the following two
methods.
23-2 Setting Parameters of "SET BRAKE PARA." and "MAIN MOTOR PARA."
23-2-1 setting the parameter of "SET BRAKE PARA."

This setting is use for adjusting the stop position of main shaft. If the main shaft stops at
smaller than 100 degree, increase the value duly. If the main shaft stops at greater than 100
degree, decrease the value duly. The range of the parameter is form 0 to 30.
Operation:

⑥TEST ENCODER
(3) Press the key " " three times to turn to page 4, which is as following:



(4) Press " " to move the cursor to "SET BRAKE PARA.", and then press " ".
(5) Press " "、" " key to change the value. （Users shall increase the value if the
main shaft usually stops at smaller than 100 degree, while decrease the value if the main shaft
usually stops at greater than 100 degree.）
(6) Press " " key to set the parameter.
23-2-2 setting the parameter of "MAIN MOTOR PARA."
This setting is use for adjusting the match of the main motor and the mechanical parts.
The range of the parameter is form 0 to 30, which default value is 0. During braking, if the
main shaft wobbles, quivers, or turn around, you should increase the value. Or the main shaft
spins too fast, you should decrease the value.
Operation:


⑥TEST ENCODER
(2) Press " " or digital key "7" to move the cursor to "SET MACHINE PARAS", and
then press " " key.
(3) Press " " key three times to turn to page 4, which is as following:


(4) Press " " to move the cursor to "MAIN MOTOR PARA.", and then press " "
key.

(5) Press " "、" " key to change the value. （During stop, if the main shaft shakes or
gyres, you can increase the value of the parameter.）
(6) Press " " key to set the parameter.
(7) Repeat the above operation till the machine brakes normally.

Chapter 24 Let The Needle Sew Down and Move the Frame
Chapter 24 Let the Needle Sew Down and Move the Frame
Warning: the operation will rotate the main shaft, and the operator should pay attention to
it.
The function is intended for special sewing. After the needles sewing down, the needles
will fasten the embroidering cloth, and then the operator can loose the cloth from the frame and
move the frame, what is for continuous embroidering in the long cloth.
Operation:
(1) Press " " key to enter into the menu of “OTHER MANAGEMENT”:
(2) Press the key “ ” to turn to page 2, then screen will show as follows:

⑥TEST ENCODER
(3) Press " " or digital key "9" to move the cursor to "TO LET NEEDLE DOWN
AND MOVE FRAME", and then press " " key.
(4) Screen shows “Press Enter to confirm”, press " " key to let the needle sew down
(Caution) or press other keys to exit. After the needle down, one can loose the cloth and move
the frame.
(5) Now, you can move the frame to the desired position. Press " " key to finish.
(6) After ending the operation, you should turn the main shaft at 100 degree (See
Chapter 20).
(7) At the moment, you can continue embroidering.

Chapter 25 No Output of the Design in Memory
Chapter 25 No Output of the Design in Memory
25-1 Summary
The function will prevent the design in memory from being copied illegally. In case the
user of machine has set a password for "NO OUTPUTTING DESIGN", the other man can not
execute the operation of "OUTPUT (DSB)" in disk management menu. If the user want to do
the operation, he must cancel the password for "NO OUTPUTTING DESIGN".
25-2 Setting a Password for "NO OUTPUTTING DESIGN"
Operation:

⑥TEST ENCODER
(3) Press " "、" " or digital key "0" to move the cursor to "NO OUTPUTTING
(4) Press " " key to confirm the operation, or press other key to give up it.
(5) Input a 4-digital password (except for "0", "00", "000", "0000"), press " " key to
finish.
25-3 Canceling the Password for "NO OUTPUTTING DESIGN"
Having set a password, you can do the steps in section 25-2 and input the password to
cancel it.
In addition, the computer will cancel the password automatically by executing of the
operation of "CLEAR ALL" in design management menu.

Chapter 26 Testing
Chapter 26 Testing
Only experienced maintenance man is permitted do this operation, or you may be

injured.
26-1 Computer Testing
This operation is to test the main board circuit and memory bank by computer itself.
26-2 Encoder Testing
This operation is to check the OPL, APL and BPL of the encoder and display the value by
turning the main shaft.
26-3 Main Shaft Speed Testing
This operation is to display the set speed and real speed comparatively by turning the
main shaft to debug the main shaft board conveniently.
26-4 Mechanical Testing
This operation is to test bar switch, limit switch, head solenoid, thread-trimming
solenoid/motor, thread-holding solenoid, thread-catching solenoid/motor and thread break
detecting, sequin device test, special embroidery device test, etc.
26-5 Turn the Main Shaft to Any Angle
This operation is to turn the main shaft from 100 degree to any angle to maintain and test
machine conveniently.

Chapter 27 Embroidering Management and Errors Statistics
27-1 Management Information in the Main Picture
In embroidery confirmation state, user can view the following management information:
Current Works, Total Works, Thread Broke Number, Thread Broke Time. As for these
definitions, see the next section.
These information are varied with the process of embroidering, they are refreshed and
displayed when the machine stop embroidering.
27-2 Statistic about embroidering
The computer can provide some statistic data for the machine manager to settle the
embroidering work.
Operation:
(1) Press “ ” key to show statistic data about embroidering, which is as following:
【EMBROIDERY】
TOTAL TIME: 4:38:45

EMB. TIME: 4:32:19
STOP TIME: 0:6:26
T.B. NUM: 10
T.B. TIME: 0:20
TOTAL WORKS: 22
POWER NUM: 2
【DESIGN】
NUMBER COUNT STITCHES TIME WORKS
12 1 21583 2:52:45 5
99 1 64 0:0:43 1
1 1 3200 1:30:18 16
0 0 0 0:0:0 0
0 0 0 0:0:0 0
0 0 0 0:0:0 0
0 0 0 0:0:0 0
0 0 0 0:0:0 0
0 0 0 0:0:0 0
0 0 0 0:0:0 0

These data are based on the computer real-time clock and the software timing. The
software times at the following condition: ⑴ the machine is electrified. ⑵ the machine stops
from running. ⑶ the machine start embroidery from stop. ⑷ the computer enters into
“embroidery confirmation”. ⑸ the computer enters into “embroidery preparation”. ⑹ the
machine finishes embroidering one normal design. ⑺ user presses “ ” key to show
statistic data about embroidering.
So, we can conclude that the computer times from the last timed time to the time of
machine power off.
【 EMBROIDERY 】 item gives the data of user’s embroidering time, and these
definitions are as following:
“TOTAL TIME” is the time that the machine is on.
“EMB. TIME” is the time that the machine is embroidering
“STOP TIME” is the time that the machine stops.
“T.B. NUM” is the amount that computer detects thread broke.
“T.B. TIME” is the average time from detecting thread broke to pulling the bar to
embroider.
“TOTAL WORKS” is the total count that the machine has finished embroidering the
normal designs by one head.
“POWER NUM” is the count that the machine is electrified.
【DESIGN】 item gives the data of the embroidered designs, which is defined as
following. In the table, “NUMBER”, “COUNT” or “STITCHES” of every row is not same
with the data of each other.
“NUMBER” is No. of the embroidered design.
“COUNT” is the amount of the normal designs that are contained in the embroidered
design.
“STITCHES” is the stitch number of the embroidered design.
“TIME” is the total time from selecting the design and entering into “embroidery
confirmation” to entering into “embroidery preparation”.
“WORKS” is the total amount that the machine embroidered the normal designs by one
head while embroidering the design.
(2) At this time, you can press “ ” key to clear all of data, or press other key to

continue.
(3) The LCD will display the error statistic table which contain the last 10 errors' time
of each error.
【ERROR】
ERROR NUM: 1
ERROR TYPE TIME TABLE OF 10 RECENT ERRORS
─ ─ ─ ─ ─
CAN NOT HOOK
─ ─ ─ ─ ─
STOP POSITION ─ ─ ─ ─ ─
ERR ─ ─ ─ ─ ─
CONTROL ─ ─ ─ ─ ─
MEMORY LOST ─ ─ ─ ─ ─
─ ─ ─ ─ ─
STEP MOTOR ERR
─ ─ ─ ─ ─
CHANGE CLR ─ ─ ─ ─ ─
OVERTIME ─ ─ ─ ─ ─
HALF RETURN ─ ─ ─ ─ ─
ERR ─ ─ ─ ─ ─
NEEDLE POSTION 2001:10:30 ─ ─ ─ ─
ERR ─ ─ ─ ─ ─
MAIN MOTOR ─ ─ ─ ─ ─
OVERTIME ─ ─ ─ ─ ─
CHANGE CLR ─ ─ ─ ─ ─
OVERLIMIT ─ ─ ─ ─ ─
─ ─ ─ ─ ─
CAN NOT TRIM
─ ─ ─ ─ ─
(4) At this time, you can press “ ” key to clear all of data, or press other key to exit.

Chapter 28 Generating the Outline Design
28-1 Summary
This function is for generating the outline design for one normal design, which can be
embroidered to dig a hole and fix the embroidering cloth。
For example：
28-2 Generating the outline design
Operation：
1、 Press “ ”key, and enter into “Mode Management”.
2、 Press “ ”key, the following menu is prompted:


⑥TEST ENCODER
3、 Press “ ” or “7” key, to move the cursor to “TO MAKE TRUE DESIGN RANGE” and
press “ ” key.
4、 Select one normal design.
5、 Input the design No. of outline design.
6、 The outline design is generated automatically.
7、 Press “ ” key to quit.

Chapter 29 Setting the Embroidery Frame Range
Chapter 29 Setting the Embroidery Frame Range
The function sets the range of the embroidery frame. When the frame is out of this range,
the machine will give the prompts: “FRAME OVER LIMIT”.
Operation:

⑥TEST ENCODER
(3) Press " "、" " or digital key "4" to move the cursor to "SET EMB. FRAME
RANGE", and then press " " key.
(4) The machine will prompt: “MOVE FRAME TO DOWN-LEFT, AND ENTER”. You
can press “ ”、“ ”、“ ”、“ ”keys to move the frame to down-left corner. And
press " " key to continue.
(5) The machine will prompt: “MOVE FRAME TO UP-RIGHT, AND ENTER”. You
can press “ ”、“ ”、“ ”、“ ”keys to move the frame to up-right corner. And
press " " key to end.

Chapter 30 Manual of Embcom Software
30-1 Soft Installation
To install this software as following:

(1) Run SETUP.EXE in Embcom Setup Disk.
(2) Click “Next>” to continue installation, otherwise click “Cancel” to quit installation.

(3) Click “Next>” to select the default destination folder.
(4) Click “Install>” to go on.

(5) Click “Finish”, which will install the Embcom software to your PC.
30-2 Soft Uninstall
(1) Open “Add/Remove Programs” in Control Panel of Windows.

(2) Select “EMBCOM” and Click “Add/Remove” button.

(3) Operate computer by hint.
(4) Click “Finish” to remove the Embcom software.
30-3 Run and Use the Embcom software
Run “EMBCOM” from install folder.
A. In first use,one must select the machine type as following: click “Communication” →
“select type”, and select “BECS-1X8”.
Special Attention: “BECS-X8” suits type 08,18,28.
“BECS-1X8” suits type
102,152,202,252,302,352,108,158,208,258,308,358,128,228,328,118,218,318.
BECS-X6 suits type BECS-16,216,26,226,266,316,366.
BECS-CX8 suits type 6C18,C18.
BECS-XX9 suits type 1X9,2X9,09,59S.

B. Click “Open Design” button to open one design.

C. Click “Send Design to Machine” button, then the soft will prompt: “Machine is ready
for receiving?”
D. (Now, the embroidery machine is ready for receiving design. For details, please see
next section.) Click “ ” button to start design receiving.
E. The computer will start to send the design to embroidery machine. Screen displays the
percentage increase from 1% to 100% (as the up-left image shows). If communication has
error or is not ready, the computer will show the up-right image or prompt: “Error in
communication or machine is not ready.”
Attentions: if you want to quit the operation during sending the design, please press
Space Key or Enter Key to stop (The mouse key is forbidden at the time).

F. Repeat the above steps to send other designs.

30-4 Communication Operation of Embroidery Machine
(1) In the main frame, press " " key to enter the design management menu, then press
“ ”to turn page and enter disk management menu, “0” and “ ” keys to enter the operation:
DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT (DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M
ARROW: MOVE, ENTER: CONFIRM
(2) The prompts is as: “INPUT A NEW DESIGN: ”, and you should input a new design
number, and press “ ” key to go on. Now, machine will prompts: “Connecting…”, and wait
connecting with PC(Personal Computer).
DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT (DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M
CONNECTING…
(3) Once the communication starts, the machine will starts receiving the new design, and
prompts as: “Processing now…”.

DISK MANAGEMENT
①DISK DIR
②INPUT
③OUTPUT (DSB)
④DEL FILE
⑤FORMAT 720K
⑥FORMAT 1.44M
PROCESS NOW…
(4) After succeeding in receiving the design, machine will return to “DISK
MANAGEMENT” frame. Otherwise, the machine will prompts as: “Communication Fail”,
which causes should be: Communication board (Board E806) has some problems, Connecting
between PC and machine is not ok, Control software of machine is not ok, or the Embcom
software in PC is not correctly running.

Chapter 31 Table of the Machine Parameters

Suggested
No. Parameter Note
Value
F1 ～ F6 are frame moving curves. The other
1 FRAME CURVE＆ANGLE F2/260
figures are starting angles for frame moving.
“Yes”: auto detecting in case of thread break
2 T.B. DETECT Yes
“No”: no detecting in case of thread break
“Yes”: machine stop after thread break detected
3 STOP AFTER T.B. DETECT Yes “No”: machine doesn’t stop and the led blinks
after thread break detected
Press the confirmation key before pulling the bar
4 PRESS KEY AFTER T.B. No
after thread break detection.
How many stitches to move backward
5 T.B. BACK STI. 0 automatically after thread break detect. Choice：
0～7 stitches，
PATCH COUNT In repairing stitch (darning), how many stitches to
6 1
(darning) do before the stop point. Choice：1～10 stitches
ACTION AFTER PATCHING After repairing stitch (darning), the main shaft can
7 SLOW
(darning) be: SLOW,STOP,NO (change)
Choice: 0～15stitches. It’s 8 if there is bottom
8 STI. NOT T.B. DETECT 8
thread detect. It’s 3 for no bottom thread detect.
The frame automatically returns to the origin
9 AUTO ORIGIN Yes
point after embroidery.
10 INITIALIZE SYSTEM! Parameters must be initialized for a new machine.
Thread break detect in case jumping stitches. It
11 T.B. DETECT WHEN JUMP No
should be set according to the real needs.
Choice: No trim or 1～7stitches（Trimming when
12 JUMP＆TRIM 3 the jumping stitches reach or exceed the set
value.）
13 JUMP STITCH SPEED 400 Rotation speed in case jump stitches
14 LOCK STICH WHEN TRIM Yes Whether to lock stitch when trimming
15 LOCK NUM. AFTER TRIM 2 Choice: 0～3。
16 LENGTH OF LOCK STI 0．6 Choice: 0.3～1.5mm。
“Yes”: in embroidery, automatic start in case of
17 START FOR SAME COLORS Yes the same needle position in color changing order
“No”: Manual start（may be used for patching）
Store the manual color change value into the color
18 STORE MANUAL-COLOR No
change order
Usually the empty stitches will be omitted by the
19 SEWING EMPTY STITCH Yes
computer. If “No”, then they won’t be omitted.
Choice: 0-3 “0” for common cloth
20 VALUE FOR THICK CLOTH 0
Increase the value for thicker cloth
21 MAX. SPEED 700 Choice: 250～1000 rpm。
22 MIN. SPEED 400 Choice: 250～600 rpm
Choice: 1～10 Speed decreases when the stitch
23 SHIFT LENGTH 5.0
length is larger than this.
Yes: shut down trimming function
24 TURN OFF TRIMMING No
No: turn on trimming function
25 TRIM MODE 3 Choice: 1～8 “1” is the shortest
26 ACTION AFTER TRIM Y Frame to X/Y, move needle

Suggested
No. Parameter Note
Value
27 FRAME AFTER TRIM No Frame moving after trimming

For common trimming, “Yes” for machine with
sensor For collective trimming it must be
28 CHECK TRIM IS OK Yes “Yes”.
“2” for electromagnetic motor “1” for miniature

29 ROUNDS FOR BRAKE 2
machines or servo main shaft motor
Slow stitches when pulling bar after trimming
30 STITCHES AFTER TRIM 2
Choice: 1～7
31 SPEED AFTER TRIM 80 Rotation speed for lock stitch
Main shaft speed when trimming
32 SPEED WHEN TRIMMING ８０
Choice: 80～250 rpm
Choice: -100~+100
33 HOOK ANGLE BY MOTOR ０
The angle increases with the set value.
34 HOOK RATIO BY MOTOR Choice: 1:9, 1:10, 1:12, 1:15, 1:18, 1:20
35 NEEDLES 6 It must be the same with the needles in machine.
Choice: 0～30
9 for electromagnetic motor main shaft/5～7 for
36 SET BRAKE PARA. 0 or 9 servo motor main shaft
When the stop position is over 100°, decrease the
value. When the stop position is less than 100°,
increase the value.
Choice: 0～30 It’s only for electromagnetic motor.
37 MAIN MOTOR PARA. 1 Increase this parameter value to avoid main shaft
vibration during braking. Usually it’s set as 1.
Choice: 80、90、100、110、120、130、140、150rpm
38 SET RUN SPEED 80
Slow stitches before acceleration in starting
39 STARTUP STITCHES 1
Choice: 1~9
40 STARTUP ACCE 12 Choice: 1～30 acceleration speed after pulling bar
41 SPEED OF SLOW EMB. 400 Shaft speed when pull bar right
It’s valid only when the color-change motor is
42 COLOR-CHANGE SPEED 12 stepping motor. The larger the value, the faster the
color-change speed.
43 ADJUST HEAD SOLENOID 0 Choice: 0～30 Voltage of head solenoid
44 PARA. OF NEEDLE DOWN 15 Choice: 0-30 stopping angle of main shaft
45 RATIO OF AC INDUCTION 0 Choice: -15～+15
46 DIP1—DIP4 For future use
50 DISPLAY STI. OR NOT Yes Display stitch count
51 OVERFRAME BY STEP No By step or continuous
52 SPEEDWHEN OVERFRAME 16 Speed of over frame
53 HIGH FRAMING SPEED 16 Choice: 1～30 speed of fast moving frame
54 LOW FRAMING SPEED 12 Choice: 1～30 speed of slow moving frame
Transfer stop code to color-change code in reading
55 STOP TO COLR No
disk files. Only for some countries/regions
The boring needle number
56 BORING NEEDLE No
“No” for no boring embroidery

Suggested
No. Parameter Note
Value
No thread break detect, trimming, or lock stitch for
the boring needle
57 BORING EMB. DISP.(mm) 0/12 Location of boring knife: 0mm or 12mm
58 CORD EMB. NEEDLE No The cord embroidery needle number
Speed limit for cord embroidery Choice:
59 SPEED FOR CORD EMB. 400
300-600rpm
Pulling bar is available only after the main shaft
60 STOP OK bef. PULL BAR
stops at 100 degree.
Please adjust this value in case the bottom thread
61 ADJ. STARTUP HOLDING 0
cannot be taken up at the time of startup.
62 DETECT T.B. MODE 1 Choice: 1,2
63 STI. FOR FILTER T.B 3 Choice: 1-6
64 SLOW STI. AFTER PATCH Choice: 0~9999
65 SPEED AFTER PATCH Choice: 80-maximum speed
66 LOCK NUM. BEFORE TRIM 2 Choice:0-2
67 LOCK LEN. BEFORE TRIM 1.0mm Choice:0.3-2.0 mm
68 LOCK SHAFT WHEN STOP 1 Choice: 0,1 0(NO),1(YES)
SPEED OF 1 STI PRIOR
69 150 Choice:60-600
TRIM
SPEED OF 2 STI PRIOR
70 80 Choice:60-500
TRIM
71 STARTUP FILTER EMPTY 1 Choice: 0,1 0(NO),1(YES)
72 SENSE OF UPPER T.B. 1 Choice:1-15
73 SENSE OF UNDER T.B. 1 Choice:1-15
74 ADJUST NIPPER SOLENOID 1 Choice:1-10
75 STATIC TRIM ANGLE 100 Choice:100 or 86
76 STI.LEN OF AUTO JUMP NO Choice:NO,3-11
77 STI. NOT T.B. AT JUMP 3 Choice:0-15
78 ADJ HEAD ACTION ANGLE 0 Choice:0-10
PARA OF SEQUIN, SPECIAL EMB, AFC.
Sequin Parameter (J type)
Choice: 0（off），1（low position needle, the first
1 SEQUIN R ON/OFF 0
needle）
Choice: 0（off），N（high position needle, the needle
2 SEQUIN L ON/OFF 0
N）
Choice: 300-600rpm the highest speed of sequin
3 SPEED FOR SEQUIN R 350rpm
embroidery
Choice: 300-600rpm the highest speed of sequin
4 SPEED FOR SEQUIN L 350rpm
embroidery
5 SEQUIN R ADJ. ANGLE Sequin delivery angle adjustment：-15~+15。
6 SEQUIN L ADJ. ANGLE Sequin delivery angle adjustment：-15~+30。
7 SEQUIN R TYPE Choice: Single, double
8 SEQUIN L TYPE Choice: single, double
9 AUTO START FOR SEQUIN No Auto startup or manual startup (pulling bar)
Choice: 0-15.”2~3” is for air valve presser foot,
10 TIME OF SEQUIN ACTION 3
and “4~5” is for stepping motor presser foot.
Control the sequin device position after thread
11 SEQUIN OFF AFTER T.B. No
break
Sequin Parameter (D type)
1 SPEED FOR SEQUIN R 400 300,310,…,the maximum speed

Suggested
No. Parameter Note
Value
2 SPEED FOR SEQUIN L 400 300,310,…,the maximum speed
3 SEQUIN R ADJ. ANGLE 0 -15～15
4 SEQUIN L ADJ. ANGLE 0 -15～15
5 AUTO START FOR SEQUIN No Yes, No
Choice: 0-15. For the presser lifted by valve, this
6 TIME OF SEQUIN ACTION 3 parameter is set at 2~3, while 4~5 for the presser
lifted by motor.
To control the position of sequin device upon the
7 SEQUIN OFF AFTER T.B. No
thread breakage.
NO, 1～4,1(2～4). This parameter is set according
to the sequin device, among which the parameter
8 MOTERS OF R Sequin
1(2~4) means the number of sequin devices driven
by one motor.
Double
Single Direction 6～40 steps, Double direction
9 Set ３MM of R Sequin direction,
13 6～40 steps
Double Single Direction 6～40 steps, Double direction
10 Set 4 MM of R Sequin direction, 6～40 steps
13
20
24
40
3/4/5/6.75/9mm
5mm
14 A Size&Color of R Sequin Yellow/Purple/Blue/Green/Red/Golden/silver/
Yellow
Cyan
3/4/5/6.75/9mm
5mm
15 B Size&Color of R Sequin Yellow/Purple/Blue/Green/Red/Golden/silver/
Blue
Cyan
3/4/5/6.75/9mm
5mm
16 C Size&Color of R Sequin Yellow/Purple/Blue/Green/Red/Golden/silver/
silver
Cyan
3/4/5/6.75/9mm
5mm
17 D Size&Color of R Sequin Yellow/Purple/Blue/Green/Red/Golden/silver/
Golden
Cyan
18 Adj Set Gap of R Seq No No/1/2
19 Value Time of R Sequin 1 Choice:0-5
NO, 1～4,1(2～4). This parameter is set according
to the sequin device, among which the parameter
20 MOTERS OF L Sequin
1(2~4) means the number of sequin devices driven
by one motor.
Double
Single Direction 6～40 steps, Double direction
21 Set ３MM of L Sequin direction,
13 6～40 steps
22 Set 4 MM of L Sequin
direction, 6～40 steps

Suggested
No. Parameter Note
Value
13
23 Set 5 MM of L Sequin direction, 6～40 steps
20
24
40
3/4/5/6.75/9mm
5mm
26 A Size&Color of L Sequin Yellow/Purple/Blue/Green/Red/Golden/silver/
Yellow
Cyan
3/4/5/6.75/9mm
5mm
27 B Size&Color of L Sequin Yellow/Purple/Blue/Green/Red/Golden/silver/
Blue
Cyan
3/4/5/6.75/9mm
5mm
28 C Size&Color of L Sequin Yellow/Purple/Blue/Green/Red/Golden/silver/
silver
Cyan
3/4/5/6.75/9mm
5mm
29 D Size&Color of L Sequin Yellow/Purple/Blue/Green/Red/Golden/silver/
Golden
Cyan
30 Adj Set Gap of L Seq No No/1/2
31 Value Time of L Sequin 1 Choice:0-5
Special Embroidery Parameter
1 SPEC. EMB. MAX SPEED 400rpm Choice: 300-600rpm
2 SPECIAL HEAD INTERVAL 162 Choice: 162,216,250…
3 CLAMP FOOT DISPLACE Choice: 0-60
1 stitch Choice: 1-4
4 RATIO OF COIL EMB.
/round
M axis returns to the origin point after the machine
5 M AXIS STOP TO ORIGIN
stops (by pulling bar).
6 ROD POS. OF ZIG Left Set the origin position of Zigzag swing rod
Trimming mode: NOT TRIM,TOP ＆
7 SPEC. EMB. TRIM BOT
BOT,BOTTOM
8 FRAME SWING FOR ZIG Choice: -9.9～-0.2，0.2～9.9
When pulling bar to move backward, the M axis
can keep still to avoid tangling in cord embroidery;
9 M AXIS BACK TO ROTATE Yes
in taping embroidery it’s necessary for M axis to
rotate (to avoid tape rotating by itself).
10 SPEC. EMB. MIN SPEED 250 Choice: 250-400
SPEC. SPEED-DOWN Choice: 1-180
11 30
ANGLE
12 SPEC. SPEED-DOWN RATIO 2 Choice: 1-4
M axis returns to the origin point at the time of
13 M AXIS ORIGIN AT T.B. Yes
thread break detection.
Timing method is taken in case angle is larger than
14 Z SHAFT CONTROL ANGLE 180 the set value. Counting method is taken in case
angle is less than the set value.
15 ADJ. CLAMP FOOT LIMIT 0 Choice: 0-250
16 MIN. HEIGHT CLAMP FOOT 0 Choice: 0-255

Suggested
No. Parameter Note
Value
17 ADJ. ZIG ROD ANGLE 1 Choice: 1, 2, 3.
18 ROTARY GAP OF M AXIS Choice: 0-10
In case of normal and sequin embroidery, the M
axis stops at the angle of the set value. When the
19 M AXIS OFF-WORK ANGLE distance between the normal embroidery head and
special embroidery head is small, this parameter
must be set as 90° to avoid bumping.
20 MAX OF ZIG Swing ANGLE 90 Choice:0-90
21 ADJ.ZIG SWING ANGLE 0 Choice:0-5
22 SPEC. EMB. JUMP&TRIM 3 stitch Choice: not trim or 1 stitch -7 stitch
23 TURN OFF ROD FOR ZIG5 No Choice: No, Yes
24 COILING EMB. MODE Normal Choice: Normal, Track
AFC Parameter
1 AUTO Frame Changer (AFC) No Choose “Yes” for automatic frame changer (AFC)
Choice: 0-15
2 AFC Interval Time 3
Interval time between (AFC) valve actions
Range: 0~10, for adjustment of compensation in
3 X GAP FOR QUILT 0
mechanical interval
Range: 0~10, for adjustment of compensation in
4 Y GAP FOR QUILT 0
mechanical interval
A-LOOPING Parameter
1 DO A-LOOPING EMB.: Yes Yes, No
Adjustable Range: 1～7. Larger parameter means
2 A-LOOPING MODE: 03
wider swing.
A-ZIG Parameter
The 1st stitch is the needle position of simple
1 A-ZIG EMB. R ON/OFF OFF
taping.
The Last stitch is the needle position of simple
2 A-ZIG EMB. L ON/OFF OFF
taping.
Range：0～5. The value is set according to the
3 A-ZIG EMB. ON/OFF TIME 2
actual motion time of simple taping device.
Range：0～100. The value is the coordinate angle
4 A-ZIG SWING ANGLE 100
of the simple taping run by the wheel.
Range：Lowest Speed～Top Speed. The top speed
5 A-ZIG MAX SPEED 600 is 1000rpm, but it still needs depend on the actual
capacity of machine.
Range：±0.2~9.9mm. It could compensate the
6 A-ZIG 5 SWING ANGLE: +0.0 embroidery range with the adjustment of the
frame.
If it is the simple cording device with double
7 A-ZIG HAS LOOSING-MOTO Y motors, this parameter shall be set as “Yes”,
otherwise, please set it as “No”.
Range：0~15. Adjust the thread delivering speed of
8 LOOSING-MOTOR PARAM 5
the entire thread-loosening motor.
Range：0~100. Setting value of angle between the
threading point and the forward direction of the
9 A-ZIG RIGHT ORIGIN POS: 0
mechanical origin of the 1st stitch simple taping
device.
Range：0~100. Setting value of angle between the
10 A-ZIG LEFT ORIGIN POS 0
threading point and the forward direction of the

Suggested
No. Parameter Note
Value
mechanical origin of the last stitch simple taping
device.
Detect whether the lifting device is at position.
11 A-ZIG DETECT UP/DOWN Y This parameter shall be set according to the actual
condition of the device.
Adjust Params of Servo Driver
1 X Emb. Param 300 Choice: 93-650
2 X Frame Param 1 260 Choice: 93-650
3 X Frame Param 2 13 Choice: 6-50
4 X Param 1-11 30 Choice: 10-50
5 X Gear Backlash 20 Choice: 0-50
6 X CMR 50 Choice: 0-100
7 X CMD 1 Choice: 0-255
Normal or Check and display the working statutes of servo
8 Inquire Servo Drivers Status
Wrong driver.
Save the parameter at interface of operation head
9 Write Servo Driver Params No into driver so as to prevent the Params from losing
at power-off
10 Restore Default Driver Params No Restore the parameter to the default values.
11 Y Emb. Param 300 Choice: 93-650
12 Y Frame Param 1 260 Choice: 93-650
13 Y Frame Param 2 13 Choice: 6-50
14 Y Param 1-11 30 Choice: 10-50
15 X Gear Backlash 20 Choice: 0-50
16 X CMR 50 Choice: 0-100
17 X CMD 1 Choice: 0-255
18 Adj All X Params +0 X parameters, 1-11 Integral adjustment.
19 Adj All Y Params +0 Y Parameters,1-11 Integral adjustment.

Chapter 32 D Type Sequin Embroidery

32-1 Brief introduction on sequin embroidery
Sequin embroidery is composed of sequins and threads. We choose those hard materials
with smooth surfaces as the sequins. Embroidery works will be shining with these sequins
attached. Design with Sequin codes has its own way of designing.
D type multi-sequin embroidery of BECS-2X6 machine is divided into two groups: one is
normal multi-sequin design, made by normal design making method. The other one is special
multi-sequin design made by normal design software with special making method attached.
For normal one, you should set sequin mode when you modify the color-changing order.
Special multi-sequin design can be directly embroidered after modification of color-changing
order.
If users want to adjust sequin, they can make change by using “sequin edit”. After
changing, the multi-sequin design will be special multi-sequin design.
Note: see《AppendixⅢ：Making of Special Multi-Sequin Design》for detailed design making
rules.
A. Applied Scope:
This system applies to sequin embroidering control system which combines normal
embroidering mechanism and sequin sending mechanism.
B. Features and Functions:
1. Two sending sequin modes: Roller and Lever;
Roller: the core part is a wheel-like device in the whole mechanism. Its operating
principle is to wheel continuous towards one direction to send sequins into position.
Lever: the core part is staff linkage. Its operating principle is to move back-and-forth to
send the sequins into position.
2. Sequin mending and sequin sending mechanism are two independent actions
3. Delivering a sequin by operating either manual separated head or centralized
4. Display working status separated head
5. Type of sequin sending and angle can be changed by operating on the control panel.
C. Specifications
1. Sequin diameter range: 3mm,4mm,5mm,6.75mm and 9mm;
2. The maximum speed for sequin embroidery is 850 rpm.
D. A/B/C/D means four delivering sequin equipment in underside depiction. If all four sequins

are delivered, A will be on the top, then B, C and D.

32-2 Embroider Sequin
Sequin embroidering should follow the steps as below:
1、Input design with sequin code, see related chapters of BECS-2X6 user manual for
details;
2、Users can edit or adjust designs if needed;
3、Set sequin embroidery parameters according to the following instructions;
4、Check the sequin delivery devices, make adjustment if necessary. Make sure that they
are under good working condition;
5、Set color-changing order;
6、Back to the main screen, embroidery confirm;
7、Pull bar to embroider.
Note: during the embroidery process, do not touch manual valve up/down switch, or
it may lead to damage of sequin device.
32-3 Sequin Design Editing
This function can edit every sequin design in the memory. Design will become special
sequin design after editing, they will not require setting sequin mode when adjust
color-changing order.
1、Press “ ”to come to other management screen:

【 OTHER MANAGEMENT】
⊗ SET DESIGN PARAS ①HI-SPEED DESIGN
④OFFSET→OFF ④FRAME TO MAKE DESIGN
⊗ PARA OF SEQUIN,SPECIAL EMB,AFC ⑧TO SET ALL HEADS PATCH→N
⑩NO OUTPUTTING DESIGN→OFF
①PRE-DISPLAY THE DESIGN→N ①SET DATE & TIME

②LCD COLORS (FOR MANAGER) ②EDIT SEQUIN DESIGN
⑥TEST ENCODER
⑨TRUN MAIN SHAFT 100°→N°
上下键或数字键移动光标，回车选择菜单
2、Press “ ” and“ ”to turn to page4, press“ ” and “ ” to move the cursor
to “EDIT SEQUIN DESIGN”, then press“ ” to enter into memory design list.
SELECTING A DESIGN
001 MEM 151
002 MEM 122
003 MEM 968
COUNT： 3
*表示花样有原点
3、Press“ ” and “ ” to move the cursor to sequin design, then press “ ”to enter
into sequin mode setting.

SELECTING A DESIGN
001 MEM 151
002 MEM 122
003 MEM 968
COUNT： 3
*表示花样有原点
NO. 1 COLOR SEQUIN-MODE：A
a) Press“ ” and “ ” to select sequin mode, press “ ” to confirm. A/B/C/D

each indicates a sequin delivery device on one machine head. If four sequins being
delivered at same time, the one on top will be sequin A, then B, C and D.
Note:“Edit sequin design ”must be done before setting “Motor Number of R (L)
Sequin” of the parameters because the choice of Sequin-mode are different from
“Motor Number of R (L) Sequin”. For example, if the maximum of “Motor Number of
R (L) Sequin” is “3” ,the selection of Sequin-mode are combination of A、B and C.
b) Press “ ” to confirm the sequin delivery mode, then users have to type in delivery
count. Press digital keys for desired sequin delivery （ranging from 1 to 9999）（if sequin
under the color uses only one mode, then type in “1” and end next step）. Press “ ” to
confirm action.
c) If multi sequin modes being required, repeat the above two steps. Otherwise, press
“ ” and “ ” till you see END or 0 in “INPUT SEQUIN MODE”, press “ ”

to save setting.
4、Continue to setting sequin mode of next color. When you complete all the settings, system
will return to Other Management screen.
5、After sequin editing, all the edited sequin designs (no matter normal or special) will
become special sequin designs.

32-4 Parameter Setting of Multi-sequin Embroidery

In this section, we will look into adjustment of sequin device and parameter setting of
multi-sequin embroidery.
Press “ ” key to enter into Other Management screen. Press “ ” and“ ” to
move the cursor to “PARA OF SEQUIN,SPECIAL EMB,AFC”, press“ ”to enter into
parameter setting screen. The process of sequin parameter setting is similar to setting other
parameters (see related machine user manuals for details).
The following are specified parameter instructions, followed by their ranges.
(1) Speed for Sequin R(L): (300,310,…,the maximum speed)
The speed depends on the sequin size. However, sewing the same sequin with different
mechanical structure, the acting angle could be different, which is directly related to the
maximum speed.
Note: the maximum speed of flat embroidery should be higher or equal to speed for
sequin embroidery.
(2) Sequin L(R) Adj. Angle ( from -15 to 15)
It is used for jiggle adjusting sequin delivery angle.
(3) Auto start for sequin(No, Yes)
When the setting is “Yes”, system will start embroidering sequin automatically.
When the setting is “No”, machine needs manually start.
(4) Time of Sequin Action(0~15)
This is to set the time period from sequin device goes down to embroidering (0-15, the
default value is 2). If the sequin device is controlled by valve, use the default value; if it is
controlled by motor, choose 4-5.
(5) Sequin off after T.B.( No, Yes)
When the setting is “Yes”, sequin presser foot will be lift up automatically in case of
thread break. When the setting is “No”, the sequin device needs manually lifting the presser
foot.
(6) Up Valve When Jump & Nocut(No, Yes)
(7) Motor Number of R (L) Sequin(NO, 1~4,1(2~4))
Tihis parameter is set by mechanism . If there is no sequin device, then you should set to
“0”.

(8) Set 3/4/5/6.75/9mm of R(L) Sequin(Lever 6~40 Degree, Roller 6~40)

This is to set sequin delivery angle. If it is roller, it should be set to single way; if it is
lever, it should be set to double way. The parameter is closely related to “left/right sequin
device A/B/C/D size and color”. For example, “A size & color of R sequin” is set to “4mm X
color”, then the angle value should be “Set 4MM of R Sequin”.
(9) A/B/C/D size & color of R/L sequin
(3/4/5/6.75/9mmRed/Green/Blue/Purple/Yellow/Cyan/silver/Golden)
Setting of this parameter depends on the mechanical structure. The order from A to D is
from front to back. Move the cursor to this parameter and press to enter.
Note: “Motor Number of R (L) Sequin” is closely related to “A/B/C/D size & color of
R/L sequin”. For example, if “Motor Number of R (L) Sequin” is set to 2, then it only displays
“A/B size & color of R/L sequin”.
(10) Sequin Gap Num of R(L) Sequin(No, 1,2)
This is to set gap number. If there is no gap, then it should be set to 0.
(11) Valve Time of Right Sequin(0~5)
32-5 Setting sequin mode when adjusting color-changing order
For normal multi-sequin design, users need to set sequin mode when they change the
color-changing order; for special multi-sequin design, users can change color-changing order
directly. The detailed operations are as follow:
1、Press“ ”, system will show this screen：
①OLD NDL:
②NEW NDL:
③INPUT&REPEAT
④MODIFY
2、Put the cursor to ①, then press“ ”. Press digital keys（Note: make sure that the digit is
within the total needle count） input color-changing position one by one, needle position
and its order are displayed on the screen. If first needle/last needle is multi-sequin device,
while last needle is multi-sequin device, then when you press the first needle/last needle
number, system will ask to select a sequin mode（for special multi-sequin design, no need
to set sequin delivery mode）.

For example, if the last needle is 6, then after pressing 6, system will display:
002：6123456
SEQUIN MODE：0
3、Press “ ”or“ ”to select a set sequin mode. Press“ ”, system will ask to input next
color-changing position. Type in proper number and needle position, then press“ ”or
“ ”.
4、Move the cursor to ④, press“ ”to set sequin mode. Screen will display the following
image:
①MODE0： [L]A1
②MODE 1：[S]A1
③MODE 2：[S]B1
④MODE 3：[S]AB1
⑤MODE 4：[S]A1B1
⑥MODE 5：[S]B1A1
⑦MODE 6：[S]A2B2
⑧MODE 7：[L]B2A2
Setting sequin delivery mode:

a) Press “ ”, then system asks to use“ ”or“ ”to select big sequin or small sequin
（sequin type）. Press “ ”to let system show the following image：
①MODE 0：[L]A
②MODE 1：[S]A1
③MODE 2：[S]B1
④MODE 3：[S]AB1
⑤MODE 4：[S]A1B1
⑥MODE 5：[S]B1A1
⑦MODE 6：[S]A2B2
⑧MODE 7：[L]B2A2
b) Press “ ”or “ ”to change sequin delivery mode. Press “ ” to confirm. A
indicates front motor delivering, B indicates middle motor delivering, C indicates rear

motor delivering, AC indicates front & rear motor overlap sequin delivering, AB
indicates front & middle motor overlap sequin delivering, BC indicates middle & rear
motor overlap sequin delivering, while ABC indicates front, middle and rear motor
overlap sequin delivering.
Note: if there are only two motors, motor B is the rear motor.
c) Press “ ” to confirm sequin delivery mode, after which system will require a sequin
delivering count. Input a number for desired sequin delivering count then press “ ”.
d) Repeat the above two steps, then press“ ” or “ ” till END appears. Press “ ”
to complete setting “SEQUIN MODE 0”。Other sequin mode settings should follow
the same steps.
32-6 Manual Operate Sequin Embroidery
Manual operate are divided into collective manual operation and separate manual
operation.
1、Collective manual operation：

The function is only applicable to machines with sequin function, namely“SEQUIN
START”,“SEQUIN FINISH”and“SEND SEQUIN”.
When the needle position is at sequin position, the manual operations are as follow:
1. Press“ ”, system shows the following image:

2. Press “ ”to move the cursor to “SET SEQUIN”. Press “ ”to let all the clamp
feet down. System stands by for sequin delivery.

3. Press“ ”to move the cursor to “CANCEL SEQUIN”. Press “ ” to let all the clamp
feet up. System ends sequin delivery.
4. Press “ ” and“ ” to move the cursor to “SEND SEQUIN”. Press “ ” once

to let the sequin devices (clamp foot down) send out a sequin.
2、Manual operating rules are:
z The thread break detect switch is embroidery switch. When it is switched to the
down side, flat and sequin embroideries are not available;
z The thread break detect lights are on the sequin delivery devices, which will be
easy for operators to watch machine head status.
Note: when the valve switch is set to the middle and blue light is on, the machine head is
under normal embroidery status.
Location of the sequin switch board

32-7 Debugging multi-sequin embroidery
1. deliver A sequin of front motor action
Shift the switch to the lower side, thread break detect switch turns green, press manual
sequin delivery button.
2. deliver B sequin of middle motor action
Shift the switch to the lower side, thread break detect switch turns red, press manual
sequin delivery button.

3. deliver C sequin of rear motor action

Shift the switch to the lower side, thread break detect switch turns to the lower side too,
press manual sequin delivery button.
32-8 Sequin mending
After thread break or manually turning on the red lamp, pull bar and the machine state is
in sequin mending. All the sequin devices will lift up; machine stops when it backs to the stop
embroidering point. Pull bar again to let the sequin device (on mending head) down for
mending. When it reaches the stop point, machine stops, then other sequin devices will be
down to continue normal embroidery. “Patch count” in machine parameter setting is
ineffective in sequin mending..

Chapter 33 Management of Coiling, Taping and Zigzag Embroidery
33-1 Function Introduction

1. Coiling function: This is a method to wind coiling thread(s) at an equal interval around
a core thread in a form of coil. Left Coiling (clockwise) and Right Coiling (counterclockwise)
are both available in coiling function, which could be opted in computer parameters.
2. Taping function: Tape can be used as embroidery material. It includes taping 1and
taping 2 (blind embroidery)
3. Zigzag function: Zigzag sewing lever swings to the right or left per stitch in regard to
the direction of original stitches. The upper thread forms zigzag on the embroidered material.
There are six special stitches: Z1, Z2, Z3, Z4, Z5 and Z6. Their stitches are as follows.
Z1 Z2 Z3 Z4 Z5 Z6
For convenience, Coiling, Taping and Zigzag-sewing are all called special embroidery in the
following.
4. Standard embroidery head and special embroidery head can be switched
automatically or manually.
5. Coiling, Taping and Zigzag functions can be switched at will.
6. The nipple of Special embroidery can be raised and lowered automatically or
manually. (Only for the machines installed with relevant apparatus)
7. The highest speeds of Standard embroidery head and special embroidery head can be
set up respectively.
8. Auto saving of the stop-embroidery point of the M axis：The embroidery work can
continue from the stop-embroidery point when the power recovers.
9. The trimming function of the special embroidery head (no trimming\trimming of the
bottom thread\trimming of both the upper and bottom threads)
10. The nipple of Special embroidery can be raised and lowered automatically before
manual frame shifting or embroidering.
11. Zigzag sewing lever can be tested manually.
33-2 Main Technique Indexes

1. The sequence of needle positions on Standard embroidery head and special

embroidery head: This control system default that the first one is special embroidery needle
position and Standard embroidery’s are from second to end.
2. Speed range of Special Embroidery: 300—600rpm, minimum of stepping precision is
10r.
3. Angle of M-axis rotated manually: 18°/step.
33-3 Manual Operation of the Special Embroidery head, and the Embroidery
Parameters Settings (Attention: the M axis can only be operated with
the first needle position.)
1. M-axis: M-axis can drive the bobbin of the Special Embroidery hand. M-axis make
the bobbin trace the stitch when embroidering.
(1) Return the M-axis to the Working Point: Press“ ”key, according to the
computer’s prompt press the digital keys or press“ ”“

/ ”to move the cursor to the option
“turn M-axis to Working Point”, and then press“ ”key to confirm. In this way, the M-axis
will return to the working point.
(2) Return the M-axis to the Origin Point: Press“ ”key, according to the computer’s
prompt press the digital keys or press“ ”、“ ”to move the cursor to the option “turn
M-axis to Origin Point”, and then press“ ”key to confirm. In this way, the M-axis will
return to origin point.
(3) M-axis rotated manually: Press“ ”key, complied with computer’s prompt , press
the digital keys or press“ ”/“ ”to move the cursor to option “M-axis rotated manually”,
press“ ”key to confirm. Complied with computer’s prompt, press“ ”、“ ”key to
rotated bobbin to the desired position step by step.
2. Make the nipple of special embroidery head up and down manually.
(1) Make the nipple of special embroidery head up: Press“ ”key, complied with
computer’s prompt , press digital key or press“ ”、“ ”to move the cursor to the option
“Make the nipple of special embroidery hand up”, press“ ”key twice to confirm. In this
way the machine will make all nipple up automatically。

(2) Make the nipple of special embroidery head down: Press“ ”key, complied with
computer’s prompt ,press digital key or press“ ”、“ ”to move the cursor to the option
“Make the nipple of special embroidery hand down”, press“ ”key twice to confirm. In this
way the machine will make all nipple down automatically。
3. Switch from Standard Embroidery head to Special Embroidery head
(1) Manual Switch: Press digital number“1”, complied with computer’s prompt, press
digital number “1” or press“ ”、“ ”key to move the cursor to①, select the first option
“the first needle position for Special Embroidery”, press“ ”key to confirm. In this way the
machine will switch the needle position to Special Embroidery hand, at the same time move
the point where the needle down to special’s.
(2) Auto Switch: When setting color-change sequence before embroidery, set the needle
number to“1”at color-change units between flat embroidery hand and special embroidery hand.
In this way the machine will switch the needle position automatically while embroidering. The
machine will stop to wait for the operation on embroidery material after it switches to the first
needle (special embroidery hand) automatically. Pull bar to continue embroidery after
finishing the operation.
4. Switch from Special Embroidery head to Standard Embroidery head
(1) Manual Switch: Press the digital key whose number is the same as the wanted needle
position’s number, then finish manual switch. In this way the machine will switch to the
selected needle position for flat embroidery hand, at the same time move the point where the
needle down to.
(2) Auto Switch: Choose the needle number to setting the color-change sequence before
embroidery, and then the machine could switch automatically in embroidery. When the
embroidery finishes, the machine will stop automatically at the Stop Code, and prompts
“embroidery paused, pull bar to continue”, waiting for operation on embroidery material. After
the operation finish, pull bar to continue. Then machine will switch to Flat Embroidery hand
automatically and continue working.
5. Switch among Coiling, Taping and Zigzag-swing Stitching
(1) Coiling Stitching Function:

a) Press digital key “1”, complied with computer’s prompt, press digital key press
“ ”、“ ”key to move the cursor to the option “the first needle position and do left
coiling stitching”, press“ ”key to confirm, then the icon“ ”will appears at the main
picture.
b) Press digital key “1”, complied with computer’s prompt, press digital key or press
“ ”、“ ”key to move the cursor to the option “the first needle position and do right
coiling stitching”, press“ ”key to confirm, then the icon“ ”will appears at the main
picture.
To get better effect, select the coiling direction according to the coiling direction of core
thread. After finishing setting, the machine will do coiling stitching matched with the special
nipple and bobbin.
(2) Taping Stitching Function: Press digital key “1”, complied with computer’s prompt,
press digital key or press“ ”、“ ”key to move the cursor to the option “the first needle
and do taping stitching 1”or“the first needle and do taping stitching 2” , press“ ”key to
1 2
confirm, then the icon“ ”or “ ”will appears at the main picture. After you finish
setting the function, the machine will do taping stitching 1 or taping stitching 2(blind
embroidery) matched with the special nipple and bobbin.
(3) Zigzag sewing Function
a) Z1 Stitching Function: Press digital key“1”, complied with computer’s prompt, press
digital key or press“ ”、“ ”key to move the cursor to the option “the first needle” and
“Z1”, press“ ”key to confirm, then the icon“ ”will appears at the main picture. Its
feature is that the lever swings once every two stitches.
b) Z2 Stitching Function: Press digital key“1”, complied with computer’s prompt, press
“ Z2”, press“ ”key to confirm, then the icon“ ”will appears at the main picture. Its
feature is that one lever swing every stitch and one lever every two stitches take place
alternately.

c) Z3 Stitching Function: Press digital key“1”, complied with computer’s prompt, press
feature is one lever swing every stitch.
d) Z4 Stitching Function: Press digital key“1”, complied with computer’s prompt, press
digital keys or press“ ”、“ ”key to move the cursor to the option “the first needle” and
feature is one lever swing every stitch and its lever swing direction is opposite to the one of
Z3.
e) Z5 Stitching Function: Press digital key“1”, complied with computer’s prompt, press
feature is the same as Z4 and it’s desirable for the embroidering of thick cords. (Refer to the
parameter: the swinging scope of the embroidery frame in zigzag sewing)
f) Z6 Stitching Function: Press digital key“1”, complied with computer’s prompt, press
feature is three stitches at the same point and one lever swing every stitch.
6. Settings of the Embroidery Parameters
(1) “SPEC, EMB. MAX SPEED” Setting the highest speed of Special Embroidery: Press
assistant mode“ ”key, press digital key "7", press“ ”or“ ”key to turn to other
pages. Complied with computer’s prompt, press digital key or press“ ”、“ ”to
move the cursor to the option “SPEC, EMB. MAX SPEED”, press“ ”to enter, press
“ ”、“ ”key to adjust the number to desired. Press“ ”key to finish setting.
(2) “SPECIAL HEAD INTERVAL”: (150，162，166，175，185，200，216，225，230，
240，250，260，270，275，280，290，300，400，455); operation ditto.

(3) “CLAMP FOOT DISPLACE” Adjusting the working position of clamp foot: “0--60”;
operation ditto. The height is for every stitch.
(4) “RATIO OF COIL. EMB.” The ratio of coiling: “1--4” ; operation ditto. The parameter
can change the coiling density; e.g. the set value 2 means one coiling every two stitches.
(5) “M AXIS STOP TO ORIGIN” The M axis returns to the origin point after the machine
stops by pulling the bar: “Y/N”; operation ditto.
(6) “ROD POS. OF ZIG” The rod position of zigzag embroidering: LEFT/RIGHT; operation
ditto.
(7) “SPEC. EMB. TRIM BOT.” Whether to trim the bottom thread by the special embroidery
head: “BOTTOM/NOT TRIM/TOP&BOT.”: operation ditto.
(8) “FRAME SWING FOR ZIG” The swinging scope of the embroidery frame in zigzag
sewing: -9.9～-0.2，0.2～9.9; operation ditto. The parameter is for Z5 stitching function and
applies to thick cords. For a thick cord, the Z5 embroidering is to move the frame to add to
the swinging scope of the lever. The parameter’s absolute value is set according to the
cord width. And the “+/-” is decided by the machine structure. The moving directions of
the lever and frame should be the same. Otherwise please change the “+/-” setting.
(9) “M AXIS BACK TO ROTATE”: Whether the M axis is to rotate when the machine returns
by pulling the bar: Y/N; operation ditto.
(10) “SPEC. EMB. MIN. SPEED” The lowest rotating speed of special embroidering: 250-400;
operation ditto. The parameter value is the lowest speed that the M axis can be decelerated
to.
(11) “SPEC. SPEED-DOWN ANGLE” :0—180; operation ditto. When the M axis rotating
angle is larger than the set value, the main axis begins to decelerate. The recommended
value is 30.
(12) “SPEC. SPEED-DOWN RATIO”: 1—4 operation ditto. The parameter is to set the
decelerating speed of the M axis. The larger the value, the faster the M axis decelerates.
(13) “M AXIS ORIGIN AT T. B.”: Y/N; operation ditto. The M axis returns to the origin point
when the thread breaks.
(14) “Z SHAFT CONTROL ANGLE” :（0-180）; operation ditto. When the rotating angle is
larger than the set value, the Z axis will wing faster.
(15) “ADJ. CLAMP FOOT LIMIT” ：（0-250）; operation ditto. The set value is added to the

limit height of the clamp foot.

(16) “MIN. HEIGHT CLAMP FOOT”(0-255)
(17) “ADJ. ZIG ROD ANGLE” The starting angle of the rod: (1、2、3) ; operation ditto.
(18) ”ROTARY GAP OF M AXIS”(0-10): The M axis of special embroidery head has mill
clearance. So without compensation, the needle will not fall in the right position. Adjust
this parameter value to ensure that the needle falls in the center of tape.
(19) “M AXIS WORK-OFF ANGLE”(0°,90°): In case of normal and sequin embroidery,
the M axis stops at the angle of the set value. When the distance between the normal
embroidery head and special embroidery head is small, this parameter must be set as 90°
to avoid bumping.
(20) “MAX OF ZIG Swing ANGLE” （0-90）
(21) “ADJ.ZIG SWING ANGLE”（0-5）Operation ditto.
(22) “SPEC. EMB. JUMP&TRIM” (not trim or 1 stitch -7 stitch)
(23) “TURN OFF ROD FOR ZIG5” (NO, YES)
(24) “COILING EMB. MODE” (Normal, Track)
33-4 Mechanical Category and Driving Mode Choice of Special Embroidery

Machines
Taping machines have three moving parts in the sense of mechanics. We define them as M
axis, E axis and clamp foot axis. M axis rotates a certain degrees every stitch to trace the stitch,
which ensures cords or tapes always in front of needle movement. E axis swings once every
one or two stitch to make the zigzag embroidery. Clamp foot axis is for lifting and lowering
the clamp foot.
1. M axis
The mechanism of M axis can be divided to two types. One is with clutch device, whose
action is controlled by electro pneumatic valve or by hand. Its advantage is that only the M
axis of the mending embroidery is moving and non-mending embroidery heads are still when
mending. This will help raise the quality and efficiency of mending. The other type is without
clutch device. Both of the two types are driven by servomotor and the origin of the M axis is
positioned by proximity switch.
2. E axis
According to the difference in motor and whether to use the proximity switch for
positioning, E axis can be divided to the following types:

1) Stepping motor, driving heads separately, without proximity switch for positioning
2) Stepping motor, driving heads by one motor, with proximity switch for positioning
3) Stepping motor, driving heads by one motor, without proximity switch for positioning
4) Servomotor driving, with proximity switch for positioning
3. Clamp foot axis
The working diagram of the clamp foot: (The clamp foot working height is the interval of
the foot’s movement with every stitch. The clamp foot rising height is the foot’s moving
distance from the bottom to the upper point in non-embroidery mode. And it’s also called the
clamp foot limited height.)
c T he clamp f oot u pper
The c lamp foot

b rising height
T he clamp foot
w orki ng height
a The clamp foot bottom
The clamp foo t
rising sketch map
According to the difference in motor and whether to use the proximity switch for
positioning, the clamp foot axis can be divided to the following types:
(1) Raising the clamp foot by hand
In this mode, the clamp foot working height relies on the rotating of the cam and the
clamp foot is raised to the limited height by hand.
(2) 2-phase stepping motor, separately driving the embroidery heads, without the holding
force and proximity switch
It uses a 2-phase stepping motor for driving every special embroidery head and
controlling its working height and limited height. The power is off and there is no the holding
force when the clamp foot stays at the upper point or bottom point. No proximity switch is
taken for positioning. And the controller by default takes that the foot is at the bottom position
when turning on the machine.
(3) 2-phase stepping motor, separately driving the embroidery heads, with the holding
force and without proximity switch
It uses a 2-phase stepping motor for driving every special embroidery head and

controlling its working height and limited height. The power is on and there is the holding
force when the clamp foot stays at the upper point, but not at the bottom point. No proximity
switch is taken for positioning. And the controller by default takes that the foot is at the bottom
position when turning on the machine.
(4) Mono-phase AC motor, driving the embroidery heads by one motor, 2 proximity
switches
clamp foot is raised to the limited height by one mono-phase AC motor driving the clamp axis.
Both the upper and bottom points are set with a proximity switch to adjust the clamp foot
rising height. Neither the upper nor bottom point has the holding force.
(5) (2-phase or 3-phase) stepping motor, driving the embroidery heads by one motor, 1
proximity switch
clamp foot is raised to the limited height by stepping motor driving the clamp axis. The upper
point is set with a proximity switch to position. The bottom point is set by parameters. Both
the upper and bottom points have the holding force.
(6) Pneumatic motor, separately driving the embroidery heads, without proximity switch
clamp foot is raised to the limited height by pneumatic motor driving the heads separately.

Appendix Ι: Rules for Using USB Disk
AppendixⅠ：Rules for Using USB Disk
No. Operation Specifications Notes

1 USB R/W Similar to floppy disk
PRIORITY BETWEEN USB AND
2 FLOPPY DISK
USB
3 SUPPORTED FORMAT FAT & FAT32
SUPPORT LONG FILENAME OR Support, but do not
4 NOT display.
e.g.
DOS 8.3（8 characters for
“ILOVEMAMA.DST”
5 FILENAME DISPLAY filename and 3 characters
will be displayed as
for suffix.） “ILOVEM~1.DST”
DISPLAY FILENAMES IN
6 CHINESE
Support
7 SUPPORT DIR OR NOT Support
8 LEVEL LIMIT FOR DIR No limit
9 FILES IN ONE DIR 1000
Return to “DISK
MANAGEMENT” or
USB R/W ERROR, OR CHANGE
10 USB DISK
“DESIGN
MANAGEMENT”, then
reinsert USB disk.
Select the subdirectory,
11 ENTER INTO A DIR then press “ ” or
“ ”.
Select “.. (DIR)”, then
12 RETURN TO THE PREVIOUS DIR
press “ ” or “ ”
OPERATING LOGICAL DRIVES Not available, it can only
13 IN ONE USB DISK operate the first logical.
14 FORMAT USB DISK Not available now.
INSTALL CHAR LIB FROM USB
15 DISK
Support
SOFTWARE FOR UPGRADING
16 USB DISK
Support
17 SPECIAL CHARACTERS Support, except for “$”.

Apendix П:All Functinns in Different Modes
AppendixⅡ：All Functions in Different Modes
Phases Press Preparing Confirm Running

Functions Key Mode Mode Mode
Instantly
4(80
1 Begin embroidering by pulling bar 9
revolutions)
2 Stop embroidering by pulling bar 9（return） 9
3 See often-used parameters 9 9
4 Set normal embroidery and idling 9 9
Set automatic color changing and

5 9 9
beginning
6 Set design direction 9
Set the sequence of automatic color

7 9 9
changing
8 See the options help 9 9
Normal or reverse display of status

9 9 9
line
10 Frame returning to the origin point 9 9
Frame returning to stop-embroidery

11 9
point
12 Manual thread trimming 9 9
13 Set main shaft acceleration speed 9 9 9
14 Set main shaft deceleration speed 9 9 9
15 Manual color-change (needle-change) 9 9
16 Turn the main shaft at 100 degree 9 9

manually
Clear stitch count and frame

17 9 9
displacement
18 Manual frame shifting 9 9
19 Set the speed of manual frame shifting 9 9
20 Set the embroidery confirmation 9
21 Release embroidery confirmation 9
Disk directory
22 9
**(22-30 DISK MANAGEMENT)
INPUT
23 9
Input design from disk to memory
OUTPUT (DSB)
24 9
Output designs from memory to disk
DEL FILE
25 9
Deleting disk files
FORMAT 720K
26 9
Formatting a 720KB disk
FORMAT 1.44M
27 9
Formatting a 1.44MB disk
INSTALL LETTER LIBS

28 9
Installing the letter library
DELETE LETTER LIBS

29 9
Deleting the letter library
30 DESIGN A LETTER DESIGN 9
SELECT DESIGN FOR EMB.

31 9
**(31-40 DESIGN MANAGEMENT)

32 SHOW MEMORY DESIGN 9
DISK INPUT
33 Input a design into memory from 9
floppy disk
COPY
34 9
Copy the designs in memory
EDIT
35 9
Edit the designs in memory
DELETE
36 9
Delete the designs in memory
DIVIDE
37 9
Divide the design in memory
COMBINE
38 9
Combine the designs in memory
PACKED DESIGN
39 9
Edit the packed design
CLEAR ALL
40 9
Clear all designs in memory
SET DESIGN PARAS (parameters)

41 9
**(41-56 OTHER MANAGEMENT)
42 FRAME TO POINT 9
43 DESIGN RANGE’S OPERATIONS 9
44 OFFSET 9
45 SET POWER RESUME 9
46 POWER RESUME 9
47 SET MACHINE PARAS 9 9

48 COMPENSATION 9
49 DHINESE/ENGLISH 9 9
50 TO SET CYCLE EMB. ON/OFF 9 9
51 HI-SPEED DESIGN 9 9
52 COMPILE PACKED DESIGN 9 9
53 COMPILE EMBROIDER. DESIGN 9 9
54 FRAME TO MAKE DESIGN 9 9
55 ADD PATCH CODE TO DESIGN 9
56 ADJUST BRAKE 9 9

Apendix Ⅲ:Making of Special Multi-Sequin Design
AppendixⅢ：Making of Special Multi-Sequin Design
1、 Dahao special multi-sequin design

The normal design making system identify a sequin code as a jump stitch, but it can not
distinguish sequin combinations from one stitch position. For instance, it can not recognize it’s
a sequin A or B at one stitch position. Dahao special multi-sequin design making is to add a
few jump stitch codes after the original sequin code（jump stitch or stitch length is less than
0.1mm）to indicate sequin combination. Thus achieve embroidering overlap sequin on one
stitch position. For instance, “A+C” means overlap sequin of A and C.
Rule is as follows:
The value of sequin A is 1，we use 1 sequin code.
The value of sequin B is 2，we use 1 sequin code plus 1 jump stitch.
The value of sequin A+B is 3，we use 1 sequin code plus 2 jump stitches.
The value of sequin C is 4，we use 1 sequin code plus 3 jump stitches.
The value of sequin A+C is 5，we use 1 sequin code plus 4 jump stitches.
The value of sequin B+C is 6，we use 1 sequin code plus 5 jump stitches.
The value of sequin A+B+C is 7，we use 1 sequin code plus 6 jump stitches.
The value of sequin D is 8，we use 1 sequin code plus 7 jump stitches.
The value of sequin A+D is 9，we use 1 sequin code plus 8 jump stitches.
The value of sequin B+D is 10，we use 1 sequin code plus 9 jump stitches.
The value of sequin A+B+D is 11，we use 1 sequin code plus 10 jump stitches.
The value of sequin C+D is 12，we use 1 sequin code plus 11 jump stitches.
The value of sequin A+C+D is 13，we use 1 sequin code plus 12 jump stitches.
The value of sequin B+C+D is 14，we use 1 sequin code plus 13 jump stitches.
The value of sequin A+B+C+D is 15，we use 1 sequin code plus 14 jump stitches.
2、 Making trace for multi-sequin
By using trace, we can easily input sequin or sequin combinations. Example: A, B, A+B,
C, A+C, B+C, A+B+C, D, A+D, B+D, A+B+D, C+D, A+C+D, B+C+D, A+B+C+D, etc.
We here take sequin B designing as an example.
1) Open any design making software. First we zoom in the blank to certain scale（it is
for easily input sequins in a place）and go into sequin state.
2) Input a sequin.
3) Since the value of sequin B is 2, we should put 2 sequins in here, which means, we
have to add another sequin.
4) Continue to type in other single-stitches.

5) You can see “stitch list” shows 2 sequins as the following image.
6) Select all stitches.

7) Making trace, group is JP, name is JP-B

8) Type in two reference point.
3、 Single needle multi-sequin, you can use “stitch form -> trace -> apply”. Then
“manual stitch” to finish entering.
4、 Others (curve）can apply trace too.

1) Click sequin button to enter “sequin state” (this is to ensure all the curve course
have sequin). Enter the curve as the following.

2) Select a target.
3) Set “target properties” and select related trace.

4) “Multi-sequin” input is finished.

5、 Making alternate sequin
This is to realize embroidering of different sequin alternate. For instance, A1B1
embroidery to realize embroidering A, B, A, B…
1) First you should design alternate trace. As the following A1B1 alternate design:

2) Apply the above trace to achieve alternate A1B1.

6、 Design maker should build up design data base
Now we have sequins: 3MM, 4MM, 5MM, 6.75MM and 9MM. while the first needle
position can have 4 sequin delivery devices at most. So we can get the following 15
combinations: A,B,AB,C,AC,BC,ABC,D,AD,BD, ABD,CD,ACD,BCD,ABCD.
The design data base emerges different sequin size with sequin combination.
If there are two sequin delivery devices A and B. A design document uses 3MM
sequin and 5MM. Then the design data base should contain 3MM-A base, 5MM-B base,
and 5MM-AB base. While the other design data base uses 4MM and 6.75MM, then the
design data base should contain 4MM-A, 6.75MM-B and 6.75MM-AB.
If there are three sequin delivery devices A, B and C. A design document uses
3MM, 4MM and 6.75MM, then the design data base should contain 3MM-A base,
4MM-B base, 4MM-AB base, 6.75MM-C base, 6.75MM-AC base, 6.75MM-BC base
and 6.75MM-ABC base. While the other design data base uses 3MM, 6.75MM and
9MM. Then the design data base should contain 3MM-A base, 6.75MM-B base,
6.75MM-AB base, 9-C base, 9-AC base, 9-BC base and 9-ABC base.
Other sequin design data bases are as the same
The alternate sequin design data base should combine single and overlap sequins.
For instance, 3MM-A sequin base and 4MM-AB sequin base can form alternate sequin
of 3MM-A & 4MM-AB, which achieves embroidering effect of A, AB, A, AB…
7、 Normal sequin design to Dahao special sequin design
According to the above rules, we just need to insert some jump stitch after “sequin code”
to change the original sequin code to “multi-sequin code”.
1) If you want to change the first sequin code to A+B sequin code, you need to
locate to that stitch first（its character is to let down the sequin）.
2) Right click “insert jump stitch” twice to insert two jump stitches after the original
sequin code.
3) You can see the stitch list as the following image. The first sequin is overlap A+B,
the second one is sequin A.
Save as the TAJIMA DST document.
文件名称 BECS-316、366 电脑刺绣机操作手册-英文
版本号 2009-01
发布日期 2009 年 08 月
软件版本
翻译
校准
审核

Embroidery Machine

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Embroidery Machine

Uploaded by

Copyright:

Available Formats

Version：2009-01

Computerized Embroidery Machine

This is to certify that the quality system of

This certificate is valid to the following product(s)/service:

Chapter 1 General Descriptions ................................................................................................. 2

1-1 Warnings and Cautions................................................................................................ 2

Chapter 2 Names of Parts about Electrical Control System ...................................................... 2

2-1 Operation Control Panel .............................................................................................. 2

Chapter 3 How to Start Embroidery........................................................................................... 2

Chapter 4 Normal Embroidery and Idling ................................................................................. 2

4-1 Relations between Normal Embroidery and Idling ..................................................... 2

Chapter 5 Color-change Management ....................................................................................... 2

5-1 Manual Needle-change (Color-change) when Stop..................................................... 2

BECS-316/366 Computerized Embroidery Machine’s Manual I

5-6 The Color-change Speed.............................................................................................. 2

Chapter 6 Setting Design Direction ........................................................................................... 2

Chapter 7 Frame Management ................................................................................................... 2

7-1 Manual Frame Shifting ................................................................................................ 2

Chapter 8 Embroidery Speed (Main Shaft Speed)..................................................................... 2

8-1 Setting the Limit Speed................................................................................................ 2

Chapter 9 Trimming Thread....................................................................................................... 2

9-1 Automatic Trimming Thread ....................................................................................... 2

Chapter 10 Disk Management...................................................................................................... 2

10-1 Directory Listing of Disk............................................................................................. 2

Chapter 11 Displaying Parameters and Displaying Language Selection..................................... 2

11-1 Viewing the Common Parameters ............................................................................... 2

Chapter 12 Other management and Setting the Parameters......................................................... 2

II BECS-316/366 Computerized Embroidery Machine’s Manual

12-1 Setting of Magnification, Rotation and Repetition...................................................... 2

Chapter 13 Management of Design in Memory........................................................................... 2

13-1 Select a Design for Embroidery................................................................................... 2

Chapter 14 Edit of the Design in Memory ................................................................................... 2

14-1 Entering the Edit of Design in Memory....................................................................... 2

Chapter 15 Operation Help .......................................................................................................... 2

BECS-316/366 Computerized Embroidery Machine’s Manual III

Chapter 16 Monogramming and Making a High-speed Design .................................................. 2

16-1 monogramming (optional) ........................................................................................... 2

Chapter 17 Compile the Packed Design and Embroidering Design ............................................ 2

17-1 Compile the Packed Design......................................................................................... 2

Chapter 18 Initialize the System Parameters during Electrifying................................................ 2

Chapter 19 Adding Patch Code to a Design................................................................................. 2

Chapter 20 The Enhanced Functions of Dot Key ........................................................................ 2

20-1 Turn the Main Axis at 100 Degree Manually .............................................................. 2

Chapter 21 Shift the Frame to Make a New Design .................................................................... 2

Chapter 22 Setting the Cyclic Embroidering ............................................................................... 2

Chapter 23 Adjust the Machine's Braking (for Manufacturer) .................................................... 2

Chapter 25 No Output of the Design in Memory......................................................................... 2

Chapter 26 Testing ....................................................................................................................... 2

IV BECS-316/366 Computerized Embroidery Machine’s Manual

26-1 Computer Testing ........................................................................................................ 2

Chapter 27 Embroidering Management and Errors Statistics...................................................... 2

27-1 Management Information in the Main Picture............................................................. 2

Chapter 28 Generating the Outline Design .................................................................................. 2

Chapter 29 Setting the Embroidery Frame Range ....................................................................... 2

Chapter 30 Manual of Embcom Software.................................................................................... 2

30-1 Soft Installation............................................................................................................ 2

Chapter 31 Table of the Machine Parameters .............................................................................. 2

Chapter 32 D Type Sequin Embroidery....................................................................................... 2

32-1 Brief introduction on sequin embroidery..................................................................... 2

Chapter 33 Management of Coiling, Taping and Zigzag Embroidery......................................... 2

BECS-316/366 Computerized Embroidery Machine’s Manual V

33-1 Function Introduction .................................................................................................. 2