HDG Datasheet 1 - Corrosion Protection Using Zinc
HDG Datasheet 1 - Corrosion Protection Using Zinc
The various processes for protecting steel from corrosion using zinc and
their characteristics
A batch process in which prepared steel is immersed in molten zinc at around 450°C
(galvanizing of fabricated articles in accordance with BS EN ISO 1461). A metallurgically
bonded coating of zinc-iron alloy layers is formed with an outer layer of pure zinc. A typical
coating thickness is 45-85 µm but thicker coatings can be produced on structural
steelwork by grit blasting the steel prior to galvanizing. A coating thickness of up to 140 µm
may then be specified. Use of a high silicon steel enables a still thicker coating of 200 µm
to be specified. Hot Dip galvanized coatings are simply specified, reproducible and easy
to inspect: if the coating looks continuous and sound, it is so. The thickness can easily be
checked without damaging the coating.
Continuous Galvanizing
The continuous hot dip galvanizing of steel strip (EN 10346), wire (EN 10244-2) and tube
(EN 10240) involves passing through molten zinc in an automated plant. Although alloyed
with the base steel, the coating is generally much thinner than batch galvanizing (typically
7-42 µm on sheet, 5-30 µm on wire and 25-55 µm on tube) and is predominantly a zinc
layer on the base steel. The hot dip galvanized sheet may be formed into a finished item as
part of the production process.
Grit blasted steel surfaces are coated with droplets of semi-molten zinc sprayed from a
special gun fed by either zinc wire or powder (EN ISO 2063). The coatings aren’t alloyed
with the base steel and while the coating can be built-up to the required thickness (typically
50-150 µm) they are always slightly porous, requiring an organic sealant to be applied. The
coating is always sensitive to shortcomings in the preparation of the steel and require a
level of skill in their application, however they can not normally be applied to the inside of
tubes and hollow sections.
Wren’s Court, 56 Victoria Road, Sutton Coldfield, West Midlands B72 1SY
T: +44 (0)121 355 8838 F: +44 (0)121 355 8727 www.galvanizing.org.uk
Zinc-Rich Painting
Process in which clean steel surfaces are coated using paints containing a high proportion
of metallic zinc dust particles to develop a film which can conduct electricity. The formulation
and application of the paint needs careful control for satisfactory performance. Paint films
are comprised of zinc particles or flakes and other components, that may be sensitive to
poor surface preparation. Coating thicknesses may vary significantly from 10-120 µm.
Zinc Electro-Plating
A zinc salt solution is used to electrolytically deposit a layer of zinc on a cleaned steel surface.
Acid or alkaline electrolytes (some may contain cyanide) can be used (EN ISO 2081). Only very
thin coatings are economically feasible (typically <10 µm) and coatings are generally uniform on
geometrically simple shapes.
Cathodic Protection
A method of corrosion protection in which a zinc anode is connected to the steel component in
the presence of an electrolyte. Specification of anodes are covered by ASTM B418 and the rate
of anode consumption will depend strongly upon the service environment.
For a given environment, the life of a zinc coating is directly proportional to its thickness. Although zinc coatings can be applied by
several different processes, only hot dip galvanizing provides a continuous, tough, metallurgically bonded coating of substantial and uniform
thickness inside and outside. The bar chart below shows how widely the thicknesses of zinc coatings can vary and emphasises the need to
be aware of those which may not give the lifetime and performance required. It is also important to ensure that all parts of a steel structure
have equivalent protection, since premature failure of the coating on small parts (e.g. fasteners) can result in major structures requiring
maintenance long before it would otherwise be necessary.
Note: Hot Dip Galvanized coatings are sometimes defined by weight of zinc per unit area. For instance, an 85 µm coating is
equivalent to 610g/m². It is important to remember that when coating weights are specified for steel sheet, the weights include both sides of the
sheet so that the life of the coating is half that for the equivalent coating weight specified in BS EN 10346.
Characteristics of different zinc coating systems
Thermal spraying 50 - 150 no Porous zinc coating Spraying of molten Sealing Overcoating
- EN ISO 2063 on prepared steel zinc of porous
surface coating
Zinc plating
(electrogalvanizing)
- individual articles 5 - 25 no Pure zinc or zinc alloy Zinc deposition by Chromate Overcoating
EN 2081 coating electrical current in treatment
aqueous electrolyte
- continuous process 2.5 - 5** no Pure zinc coating
EN 10131
Metallic coatings
With zinc dust
a) Sherardizing 20 - 30** yes Zinc-iron alloy coating Diffusion of zinc Overcoating
EN 13811 onto steel below the
melting point of zinc
Painting BS 4652
Protection High purity zinc anodes (99.995%) can be used to sacrificially protect iron and steel structures that are
immersed or buried in an efficient electrolyte. If the zinc anode is to function efficiently it is vital that it is
always in good contact with the steel that it is protecting. The rate at which zinc anodes are consumed in sea
water is about 12kg/ampere-year. On bare steel the average current density is about 0.10A/m2.
Therefore, to protect 100m2 of bare steel requires approximately 120kg/year of zinc anodes.
* Alloying of a zinc coating by specific heat treatment especially with galvanized steel strip
** Typical values
This sheet is part of the series ‘HDG Datasheets’ and can be requested from
Galvanizers Association. Published August 2015.