BS en Iso 17985
BS en Iso 17985
BS en Iso 17985
17895:2005
ICS 87.040
12&23<,1*:,7+287%6,3(50,66,21(;&(37$63(50,77('%<&23<5,*+7/$:
BS EN ISO 17895:2005
National foreword
This British Standard is the official English language version of
EN ISO 17895:2005. It is identical with ISO 17895:2005.
The UK participation in its preparation was entrusted to Technical Committee
STI/10, Test methods for paints, which has the responsibility to:
Summary of pages
This document comprises a front cover, an inside front cover, the EN ISO title
page, the EN ISO foreword page, the ISO title page, pages ii to v, a blank page,
pages 1 to 11 and a back cover.
The BSI copyright notice displayed in this document indicates when the
document was last issued.
ICS 87.040
English version
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17895:2005: E
worldwide for CEN national Members.
EN ISO 17895:2005
I NESO 71:5982005 (E)
Foreword
This document (EN ISO 17895:2005) has been prepared by Technical Committee ISO/TC 35
"Paints and varnishes" in collaboration with Technical Committee CEN/TC 139 "Paints and
varnishes", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by September 2005, and conflicting national
standards shall be withdrawn at the latest by September 2005.
Endorsement notice
The text of ISO 17895:2005 has been approved by CEN as EN ISO 17895:2005 without any
modifications.
2
EN ISO 17895:2005
INTERNATIONAL ISO
STANDARD 17895
First edition
2005-03-15
Reference number
ISO 17895:2005(E)
© OSI 5002
EN ISO 17895:2005
IS:59871 O5002(E)
DPlcsid Fremia
ihTs PDF file may ctnoian emdebt dedyfepcaes. In ccaocnadrw eith A'ebods licensilop gnic,y this file mairp eb ynted iv roweb detu
slahl ton ide ebtlnu deess the typefaces whice era hml era deddebicsnede to i dnanstlaled t noeh computfrep reormign tide ehtin.g In
wodlnidaot gnhis file, trapise atpecc tiereht nser ehnopsiiblity fo not infriigngn A'ebods licensilop gnic.y ehT ISO tneClar Secrteiraat
caceptl on siibality in this .aera
Ai ebods a tredamafo kr Aebod SystemI sncotaropr.de
teDails fo teh softwacudorp erts sut deo crtaee this PDF file cna f ebi dnuon tlareneG eh Info leratit evo the file; tP ehDc-Frtaeion
marapterew setpo erimizde for irpnti.gn Evyre caer neeb sah taken to sneeru that the file is suitlbae fosu re yb ISO memdob rebeis. In
tlnu ehikletneve y ttah lborp aem leratit gno it is f,dnuo plsaee inform ttneC ehlar Secrteiraat ta the serddaig sleb nevwo.
© ISO 5002
All irthgs erse.devr lnUeto sswrehise specified, on trap fo this lbupictaion maeb y cudorperro de tuilizi den yna form ro na ybm ynae,s
lecetrinoc ro mecinahcal, inclidung tohpcoiypodna gn micrfoilm, wittuoh repmissii non writign from ietI rehSa Ot tsserdda eh ebolw or
IS'Os memreb i ydobn the cnuotrfo y ttseuqer ehe.r
ISO cirypothg fofice
saCe tsopale 65 •eneG 1121-HC 02 av
leT. 4 + 10 947 22 1 11
xaF0 947 22 14 + 9 74
E-mail [email protected] gr
We bwww.is.o gro
Pulbisdehi n Switlrez dna
Contents Page
Foreword ............................................................................................................................................................ iv
Introduction ........................................................................................................................................................ v
1 Scope...................................................................................................................................................... 1
2 Normative references ........................................................................................................................... 1
3 Terms and definitions........................................................................................................................... 1
4 Principle ................................................................................................................................................. 2
5 Apparatus............................................................................................................................................... 3
6 Reagents and materials........................................................................................................................ 3
7 Sampling ................................................................................................................................................ 4
8 Procedure............................................................................................................................................... 4
9 Evaluation .............................................................................................................................................. 7
10 Precision ................................................................................................................................................ 8
11 Test report.............................................................................................................................................. 9
Annex A (informative) Gas chromatogram of the reference compound mixture and tetradecane.......... 10
Bibliography ..................................................................................................................................................... 11
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17895 was prepared by Technical Committee ISO/TC 35, Paints and varnishes.
Introduction
The requirements imposed today by authorities, for health and environmental reasons, include the
assessment of the content of residual monomers and organic saturated volatiles, sometimes down to minute
traces.
This International Standard is one of a series of standards dealing with the VOC content of paints, varnishes
and related products: ISO 11890-1 (see the Bibliography) specifies a method for determining VOC contents
greater than 15 % (by mass), ISO 11890-2 is applicable to VOC contents between 0,1 % and 15 % (by mass).
This International Standard describes a method for determining VOC contents between 0,01 % and 0,1 % (by
mass). In contrast to ISO 11890-1 and ISO 11890-2, this standard is applicable to volatile organic compounds
with boiling points up to 250 °C.
blank
EN ISO 17895:2005
INTENRATIONAL TSANDADR IS:59871 O5002(E)
1 Scope
This International Standard specifies a gas-chromatographic method of quantitatively determining the volatile
organic compound (VOC) content (i.e. the content of organic compounds with boiling points up to 250 °C)
under standard conditions (101,325 kPa) of low VOC content emulsion paints (in-can VOC). The method is
applicable to VOC contents between 0,01 % and 0,1 % (by mass).
The main purpose of the method is to qualify low-VOC emulsion paints, not routine quality control.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 2811-1, Paints and varnishes — Determination of density — Part 1: Pyknometer method
ISO 2811-2, Paints and varnishes — Determination of density — Part 2: Immersed body (plummet) method
ISO 2811-3, Paints and varnishes — Determination of density — Part 3: Oscillation method
ISO 2811-4, Paints and varnishes — Determination of density — Part 4: Pressure cup method
ISO 3696, Water for analytical laboratory use — Specification and test methods
ISO 15528, Paints, varnishes and raw materials for paints and varnishes — Sampling
3.1
volatile organic compound
VOC
any organic liquid and/or solid that evaporates spontaneously at the prevailing temperature and pressure of
the atmosphere with which it is in contact
NOTE 1 As to current usage of the term VOC in the field of coating materials, see volatile organic compound content
(VOC content).
NOTE 2 Under U.S. government legislation, the term VOC is restricted solely to those compounds that are
photochemically active in the atmosphere (see ASTM D 3960). Any other compound is then defined as being an exempt
compound.
[ISO 4618]
3.2
volatile organic compound content
VOC content
mass of the volatile organic compounds present in a coating material, as determined under specified
conditions
NOTE The properties and the amounts of compounds to be taken into account will depend on the field of application
of the coating material. For each field of application, the limiting values and the methods of determination or calculation
are stipulated by regulations1) or by agreement.
[ISO 4618]
3.3
in-can VOC
volatile organic compound present in a water-based emulsion paint
3.4
emulsion paint
latex paint
coating material in which the organic binder is an aqueous dispersion
[ISO 4618]
3.5
full evaporation
method of transferring the VOCs in a liquid sample from the liquid to the vapour phase
NOTE Although a headspace injector with septum-sealable vials is used for introduction of a test portion of the
vapour phase into the chromatographic column, the full evaporation method differs substantially from conventional
headspace analysis in which equilibrium is established. Since the vial contains very small amounts of sample, virtually all
the VOCs enter the vapour phase when heated to a certain temperature [3].
3.6
stock reference compound mixture
mixture prepared from pure substances for use in the standard addition method
NOTE The concentration of the stock reference compound mixture is determined by the initial masses of the
individual components in the sample and their degree of purity.
3.7
multiple standard addition method
method of determining the VOC content in which a known amount of stock reference compound mixture is
added to the sample
4 Principle
The VOCs in a very small amount of thinned sample are fully evaporated in a headspace injector and then
determined by gas-chromatographic analysis, as follows:
A few microlitres of the sample diluted with buffer solution are heated to 150 °C in a septum-sealed vial and,
when fully evaporated, some of the vapour phase is transferred to a non-polar capillary column. The peak
areas of all the components with retention times less than that of tetradecane (boiling point 252,6 °C) are
integrated. Standard additions of a stock reference compound mixture (see 3.6) are employed at four
1) For the purposes of this International Standard, the applicable regulations are given in European Commission
decision 96/13/EC dated 1996-01-06 which defines all organic compounds having a boiling point (or initial boiling point) of
not more than 250 °C at normal pressure (101,325 kPa) as volatile organic compounds (VOCs).
concentration levels to determine the VOC content. The result is based on the average response factor of the
reference compound mixture.
NOTE Determination of individual components in the sample, or of standards prepared separately from emulsions or
emulsion paints which are as free of VOCs as possible, can be used to validate the analytical system.
5 Apparatus
Ordinary laboratory apparatus and glassware, together with the following:
5.1 Gas chromatography system, consisting of a headspace injector, preferably with an automatic
sample changer, a temperature-programmable gas chromatograph suitable for capillary gas chromatography,
a flame-ionization detector or mass-selective detector and a data evaluation system. All the components of
the headspace injector which come into contact with the sample (e.g. dispensing needle, dispensing valve,
transfer tube) shall be capable of being heated.
5.2 Non-polar fused-silica capillary column, with a stationary phase consisting of 95 % to 100 %
dimethylsilicone and 5 % to 0 % of phenylsilicone chemically bound to the column.
NOTE Capillary columns having a length of 30 m and an internal diameter of 0,32 mm coated with 95 %
dimethylsilicone and 5 % phenylsilicone (film thickness approximately 1 µm) were found to be suitable in an interlaboratory
trial.
5.5 Septum-sealable vials, having a capacity of about 20 ml, with a butyl or silicone rubber septum coated
with polytetrafluoroethylene (PTFE). Since the test conditions specified in this International Standard result in
fairly high pressures in the vials, care shall be taken to ensure that they are tightly sealed.
6.1 Gases:
Carrier gas: dry, oxygen-free helium, nitrogen or hydrogen having a purity of at least 99,995 % (by
volume).
Detector gas mixture: hydrogen having a purity of at least 99,995 % (by volume) and synthetic air free of
organic compounds.
6.2 Stock reference compound mixture, containing the following representative reference compounds:
butanol;
butyl acrylate;
2-ethylhexyl acrylate;
styrene;
vinyl acetate.
Weigh, to the nearest 1 mg, about 1 g of each of the reference compounds into a septum-sealable vial using
the analytical balance (5.7), adding the high boilers before the low boilers. Remove the cap only to allow each
reference compound to be introduced. Add about 1 000 mg/kg polymerization inhibitor (6.4) to the mixture.
NOTE Evaporation of readily volatile substances during weighing can be reduced by precooling and pipetting the
reference compounds.
6.3 Citrate buffer, pH 5,0: obtainable commercially in ready-to-use form or can be prepared in-house by
making up 20,265 g of citric acid and 7,840 g of sodium hydroxide to 1 l at 20 °C with deionized water in a
volumetric flask.
7 Sampling
Take a representative sample of the product to be tested, as described in ISO 15528.
8 Procedure
Carry out triplicate determinations of the test sample without standard additions (see 8.2.3) and of each of the
four test samples containing standard additions (see 8.2.4).
8.2.1 General
Sample preparation involves diluting the sample of emulsion paint (see 8.2.2) and preparing the test samples
with and without standard additions (see 8.2.4 and 8.2.3, respectively).
Carry out the sample preparation quickly since the original sample diluted with citrate buffer is prone to serum
formation and losses may occur as the result of volatilization of individual compounds.
Weigh 10 g of the original sample (emulsion paint) and 10 g of citrate buffer (6.3) to the nearest 0,1 g into a
20 ml septum vial (5.5), seal and mix.
8.2.3 Preparation of test samples for analysis without multiple standard additions
Vigorously shake the sealed septum vial containing the diluted sample of emulsion paint (prepared as in 8.2.2),
then immediately remove any excess vapour by piercing the septum with a 2 ml disposable syringe (5.4). For
the analysis, weigh aliquots of (15 ± 3) mg to the nearest 0,1 mg into each of three vials (5.5) and seal the
latter immediately.
NOTE Higher initial test sample masses will result in errors in the result due to the increase in pressure.
8.2.4 Preparation of test samples for analysis with multiple standard additions
Prepare four diluted samples of emulsion paint as in 8.2.2 and add, using a 50 µl syringe (5.3), about 10 µl,
20 µl, 30 µl and 40 µl of stock reference compound mixture (6.2) (a different volume to each vial). Weigh each
vial to the nearest 0,1 mg. Close the vials firmly and mix well.
Shake the sealed vials vigorously once again, then remove any excess vapour by piercing the septum with a
2 ml disposable syringe (5.4). For the analysis, weigh an aliquot of about (15 ± 3) mg of these diluted test
samples containing standard additions to the nearest 0,1 mg into each of three empty vials (5.5) and seal the
latter immediately.
Key
0 original sample
A10, A20, A30, A40 standard additions of 10 mg, 20 mg, 30 mg and 40 mg of the stock reference compound mixture
8.3 Analysis
Place the vials prepared as in 8.2.3 and 8.2.4 in the headspace injector.
Adjust the gas-chromatographic conditions to the design of the apparatus. Two examples of this are given
below.
Capillary column: Length 30 m, internal diameter 0,32 mm, coated with 95 % dimethylsilicone and 5 %
phenylsilicone (film thickness about 1 µm)
Capillary column: Length 30 m, internal diameter 0,32 mm, coated with 95 % dimethylsilicone and 5 %
phenylsilicone (film thickness about 1 µm), joined to a methyl-deactivated 1,5 m × 0,15 mm
restrictor capillary inserted between column and detector
Carrier gas flow rate: About 1,8 ml/min, equivalent to pressure settings of pheadspace = 160 kPa, pGC = 125 kPa
Determine the retention time of tetradecane by a separate GC analysis. It defines the integration end point for
the VOC determination.
9 Evaluation
Evaluate the chromatogram by integrating all the peaks to obtain their sum up to the retention time of
tetradecane.
NOTE In determining the peaks, the signal/noise ratio should be at least 5:1 for the peak to be included in the
integration.
The accuracy of the determination in the standard addition method is substantially affected by the precision
with which the samples are weighed into the vials. To avoid losses due to premature evaporation, it is
essential to work quickly. For this reason, sample masses of 15 mg can only be reproduced approximately in
practice, and it is therefore desirable to normalize the peak areas of each analysis to 1 mg by dividing them by
the actual sample mass and using the equation:
A
Anorm =
mp
m vd ×
m p + m cb
where
A is the integrated area, in area units, determined up to the retention time of tetradecane;
mvd is the mass, in milligrams, of the test sample (EP-0-1 to EP-A40-3, see Figure 1);
mcb is the mass, in grams, of citrate buffer added to the original sample.
First calculate, from the normalized areas, Anorm, the mean, A norm( x ) , in area units/milligram, of the three
analyses made on the test samples without a standard addition and those made on each set of three test
samples with a standard addition of 10 mg, 20 mg, 30 mg and 40 mg, using the equation:
3
1
Anorm(x ) = ×∑
3 i =1
Anorm(x )
where
Anorm(x) is the area, normalized to 1 mg of emulsion paint, of the test samples without standard
additions and of those with standard additions of 10 mg, 20 mg, 30 mg or 40 mg, in area units
per milligram;
x is the subscript 0, 10, 20, 30 or 40 for the test samples with standard additions of 0 mg, 10 mg,
20 mg, 30 mg and 40 mg, respectively.
Then carry out a linear regression analysis either by calculation or, alternatively, by calculation and plotting the
mean area obtained in this way against the associated standard addition.
From the intercept, Ay, on the vertical axis and the slope, B, of the linear regression plot (see Figure 2),
calculate the amount, mvoc, in milligrams, of VOC in the original sample mass, mp, using the equation:
Ay
m VOC =
B
The in-can VOC content, wVOC, in milligrams per kilogram, is then given by:
m VOC
w VOC = × 1 000
mp
where mp is the mass, in grams, of the original sample of emulsion paint (EP).
The conversion to the in-can VOC content in grams per litre, ρVOC, requires a knowledge of the density of the
emulsion paint, which can either be obtained from the manufacturer's information or be determined by one of
the methods specified in ISO 2811-1 to ISO 2811-4. In arbitration cases, the value determined as specified in
ISO 2811-1 shall be regarded as final.
w VOC × ρ EP
ρ VOC =
1 000
where
ρEP is the density, in grams per millilitre, of the original sample of emulsion paint.
10 Precision
10.1 General
Four different interlaboratory studies were conducted in eight laboratories. The following results were
obtained:
The repeatability limit r is the value below which the absolute difference between two single test results,
obtained on identical material by one operator in one laboratory within a short interval of time using the
standardized test method, may be expected to lie. For this method, r is 10 %, with a 95 % probability.
The reproducibility limit R is the value below which the absolute difference between two test results, obtained
on identical material by operators in different laboratories using the standardized test method, may be
expected to lie. For this method, R is 30 %, with a 95 % probability.
Key
X standard addition, in mg
Y Anorm(x), in area units/mg
11 Test report
b) all details necessary for complete identification of the product tested (manufacturer, trade name, batch
number, etc.);
d) the in-can VOC content, in milligrams per kilogram or grams per litre, as specified in Clause 9;
Annex A
(informative)
Key
X elution time, in min
Y detector signal, in mV
NOTE The retention time of tetradecane is determined by separate GC analysis (see 8.4). It is shown in the
chromatogram together with the peaks of the reference compounds just to indicate its retention time in comparison with
those of the reference compounds.
Figure A.1 — Gas chromatogram of the reference compound mixture and tetradecane
Bibliography
[2] ISO 11890-1, Paints and varnishes — Determination of volatile organic compound (VOC) content —
Part 1: Difference method
[3] ISO 11890-2, Paints and varnishes — Determination of volatile organic compound (VOC) content —
Part 2: Gas-chromatographic method
[4] ASTM D 3960, Standard Practice for Determining Volatile Organic Compound (VOC) Content of
Paints and Related Coatings
[5] MARKELOV, M, GUZOWSKI, J.P., Jr., Anal. Chim. Acta, 1993, 276, pp. 235-245
Revisions
British Standards are updated by amendment or revision. Users of
British Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: [email protected]. Standards are also
available from the BSI website at http://www.bsi-global.com.
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: [email protected].
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.
Email: [email protected].
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsi-global.com/bsonline.
Further information about BSI is available on the BSI website at
http://www.bsi-global.com.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
BSI written permission of BSI must be obtained.
389 Chiswick High Road Details and advice can be obtained from the Copyright & Licensing Manager.
London Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: [email protected].
W4 4AL