Professional Documents
Culture Documents
Sievert India Pvt. LTD.: Question Paper
Sievert India Pvt. LTD.: Question Paper
QUESTION PAPER
Method : PAUT
Level : II
Examination Type : Theory
Name of candidate :-
Finish Time :-
Signature of Examiner :-
Marks Evaluated by
Total Marks Marks Obtained %
ASNT level III (UT)
Signature of Candidate.
1
SIEVERT INDIA PVT. LTD.
16 & 17, Plot-2, Phase-II, Sector-2, Nerul, Navi Mumbai-400706
Phone: +91 22 27727060/27732001, Fax: +91 22 27727076
Email: [email protected] Web: www.sievert.in
a. High speed inspection
b. Software control of probe characteristics
c. Multiple angle inspection
d. All of the above
e. a & c only
4. The beam steering capabilities of the phased array probe is best achieved by
a. Element width
b. Element size
c. Element gap
d. Total Aperture
7. When it is said that the phased array equipment is 32/128 than what does it means?
a. Probe with only 32 elements can be connected
b. 32 elements can activated simultaneously at a given time
c. 128 can be activated simultaneously at a given time
d. All of the above
a. 32 steps/mm
b. 12 steps/mm
c. 2100 steps/mm
d. 22 steps/mm
2
SIEVERT INDIA PVT. LTD.
16 & 17, Plot-2, Phase-II, Sector-2, Nerul, Navi Mumbai-400706
Phone: +91 22 27727060/27732001, Fax: +91 22 27727076
Email: [email protected] Web: www.sievert.in
9. RA stands for Distance between the wedge reference point and the reflector (true/false).
11. Phased array Module is designated as “PA 16/128” where 16/128 denotes
a. 16 pulsers and a total of 128 elements
b. 128 pulsers and a total of 16 elements
c. 16 pulse and a total of 128 elements
d. 128 pulse and a total of 128 elements
3
SIEVERT INDIA PVT. LTD.
16 & 17, Plot-2, Phase-II, Sector-2, Nerul, Navi Mumbai-400706
Phone: +91 22 27727060/27732001, Fax: +91 22 27727076
Email: [email protected] Web: www.sievert.in
d. Dead zone at top surface (OD)
a. >50 mm
b. <50 mm
c. >25 mm
d. <25 mm
20. Increasing PRF too high results in ghost or phantom signals (True / False).
21. “Dead elements” are elements in an array that are no longer active in a phased array
probe. This is a result of
a. Failed elements or their soldered connections in the probe
b. Poor or intermittent contacts at the connection terminals or in the cables
c. Failed pulser – receiver boards
d. All of the above potential sources
22. What is not an advantage of 12 bit digitisation over 8 bit digitisation?
a. Improved resolution
b. Improved signal to noise ratio
c. Smaller file size
d. Option to reduce gain to avoid signal saturation
23. Reduction of what parameter will increase the size of a data file collected in a phased –
array S-scan?
a. A-scan time window
b. Number of angles sampled in the S-scan
c. Data sampling rate (12 bit to 8 bit)
d. Scan axis resolution (sample internal)
24. Decreasing which parameter will decrease the size of a data file collected in a phased –
array S-scan?
a. A-scan time window length (range)
4
SIEVERT INDIA PVT. LTD.
16 & 17, Plot-2, Phase-II, Sector-2, Nerul, Navi Mumbai-400706
Phone: +91 22 27727060/27732001, Fax: +91 22 27727076
Email: [email protected] Web: www.sievert.in
b. Number of angles sampled in the S-scan
c. A-scan window ADC rate
d. All of the above
25. Some UT instruments permit selection of “filters” in the receiver to optimise signal results.
When using a band – pass filter what is the process called?
a. Probe bandwidth
b. Probe centre frequency
c. Cable length
d. The number of elements in the array
29. How much frequency and how many no.s of total element used in cobra scanner probe?
30. Velocity calibration can be performed using:
a. Reflectors from two known radii
b. Reflectors from two side drilled holes at known depths
c. Reflectors from two blocks of the same material with known thicknesses
d. All of the above
31. Which skew (degree) angle used for the transverse indications:
a. 0 degree
b. 90 degree
c. 200 degree
d. 270 degree
5
SIEVERT INDIA PVT. LTD.
16 & 17, Plot-2, Phase-II, Sector-2, Nerul, Navi Mumbai-400706
Phone: +91 22 27727060/27732001, Fax: +91 22 27727076
Email: [email protected] Web: www.sievert.in
d. Under cut
37. If the gain is set too high when producing the wedge delay envelope:
a. Some or all of the envelope will be drawn off the calibration screen area
b. The instrument will compensate for this
c. An error may result when applying “calibration”
d. Both a & c
39. For a given linear phased array probe, what variable is available to the operator to limit its
near field length?
a. Frequency
b. Number of elements used
c. Pulse duration of the pulser voltage
d. Voltage to the pulser
6
SIEVERT INDIA PVT. LTD.
16 & 17, Plot-2, Phase-II, Sector-2, Nerul, Navi Mumbai-400706
Phone: +91 22 27727060/27732001, Fax: +91 22 27727076
Email: [email protected] Web: www.sievert.in
41. Phased array applications use a group of elements in firing a specific focal law. The
dimension of the equivalent probe size in the focal law is considered:
a. The total aperture
b. The active aperture
c. The passive aperture
d. None of the above
45. Short duration pulses from well damped transducers should significantly improve?
a. near surface resolution
b. far field penetration
c. near zone length
d. all the above
46. Increasing the length of the pulse applied to the search unit will
a. increase penetration but decrease resolution
b. decrease penetration and increase resolution
c. increase both penetration and resolution
d. decrease both resolution and penetration
48. Two signals were compared in amplitude to each other. The second was found to be 14 dB
less than the first. This change could have represented a change of….
a. 70 % FSH to 14 % FSH
b. 100 % FSH to 50 % FSH
c. 20 % FSH to 100 % FSH
d. 100 % FSH to 25 % FSH
49. The thinner the crystal, the higher the frequency (true or false).
7
SIEVERT INDIA PVT. LTD.
16 & 17, Plot-2, Phase-II, Sector-2, Nerul, Navi Mumbai-400706
Phone: +91 22 27727060/27732001, Fax: +91 22 27727076
Email: [email protected] Web: www.sievert.in
50. Higher frequency sound beams produce higher levels of sensitivity and resolution, but less
ability to penetrate test objects to great depths (true or false).
55. Volumetric individual defect length is acceptable as per ‘welding of pipelines and
related facilities’…………
57. What’s effect of the averaging on the signal in a Data Acquisition System:
a. Decrease in SNR ratio
b. increasing the Effects of Noise
c. Reducing the Effects of Noise
d. None of the above
8
SIEVERT INDIA PVT. LTD.
16 & 17, Plot-2, Phase-II, Sector-2, Nerul, Navi Mumbai-400706
Phone: +91 22 27727060/27732001, Fax: +91 22 27727076
Email: [email protected] Web: www.sievert.in
METHOD: PAUT
NAME:
INSTRUCTIONS:
1. The correct answer should be darkened properly. e.g. 1. Ⓐ ● ⒸⒹⒺ
2. Only one answer should be darkened.
3. No negative marking.
4. Answer explanation and fill in the blank questions on separate sheet and attach.
1. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 31. ⒶⒷⒸⒹⒺ
2. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 32. ⒶⒷⒸⒹⒺ
3. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 33. ⒶⒷⒸⒹⒺ
4. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 34. ⒶⒷⒸⒹⒺ
5. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 35. ⒶⒷⒸⒹⒺ
6. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 36. ⒶⒷⒸⒹⒺ
7. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 37. ⒶⒷⒸⒹⒺ
8. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 38. ⒶⒷⒸⒹⒺ
9. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 39. ⒶⒷⒸⒹⒺ
10. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 40. ⒶⒷⒸⒹⒺ
11. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 41. ⒶⒷⒸⒹⒺ
12. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 42. ⒶⒷⒸⒹⒺ
13. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 43. ⒶⒷⒸⒹⒺ
14. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 44. ⒶⒷⒸⒹⒺ
15. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 45. ⒶⒷⒸⒹⒺ
16. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 46. ⒶⒷⒸⒹⒺ
17. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 47. ⒶⒷⒸⒹⒺ
18. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 48. ⒶⒷⒸⒹⒺ
19. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 49. ⒶⒷⒸⒹⒺ
20. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 50. ⒶⒷⒸⒹⒺ
21. Ⓐ Ⓑ Ⓒ Ⓓ Ⓔ 51. ⒶⒷⒸⒹⒺ
9
SIEVERT INDIA PVT. LTD.
16 & 17, Plot-2, Phase-II, Sector-2, Nerul, Navi Mumbai-400706
Phone: +91 22 27727060/27732001, Fax: +91 22 27727076
Email: [email protected] Web: www.sievert.in
22. ⒶⒷⒸⒹⒺ 52. ⒶⒷⒸⒹⒺ
23. ⒶⒷⒸⒹⒺ 53. ⒶⒷⒸⒹⒺ
24. ⒶⒷⒸⒹⒺ 54. ⒶⒷⒸⒹⒺ
25. ⒶⒷⒸⒹⒺ 55. ⒶⒷⒸⒹⒺ
26. ⒶⒷⒸⒹⒺ 56. ⒶⒷⒸⒹⒺ
27. ⒶⒷⒸⒹⒺ 57. ⒶⒷⒸⒹⒺ
28. ⒶⒷⒸⒹⒺ 58. ⒶⒷⒸⒹⒺ
29. ⒶⒷⒸⒹⒺ 59. ⒶⒷⒸⒹⒺ
30. ⒶⒷⒸⒹⒺ 60. ⒶⒷⒸⒹⒺ
10