Mvne
Mvne
Ans. All bodies having mass and elasticity are capable of vibration. When external force is applied on
the body, the internal forces are set up in the body which tend to bring the body in the original
position. The internal forces which are set up are the elastic forces which tend to bring the body in the
equilibrium position. Consider an example of swinging of pendulum.
At extreme position whole of the kinetic energy of the ball is
converted into elastic energy which tends to bring the ball in
the equilibrium/mean position. At mean position whole of
the, elastic energy is converted into kinetic energy and body
continues to move in opposite direction because of it. Now
the whole of kinetic energy is converted into elastic energy
and this elastic energy again brings the ball to the
equilibrium position. In this way, vibratory motion is
repeated indefinitely and exchange of energy takes place.
This motion which repeats itself after certain interval of time
is called vibration.
Ans. Importance of vibration study. The imp of vibration study is to reduce or eliminate vibration
effects over mechanical components by designing them suitably. Proper design and manufacture of
parts will reduce unbalance in engines which causes excessive and unpleasant stress in rotating
system because of vibration, roper design of machine parts will reduce and tear due to vibration and
loosening parts. The proper designing and material distribution prevent the locomotive m leaving the
track due to excessive vibration which may result in accident or heavy loss. Proper designing of
structure buildings can prevent the condition of resonance which causes dangerously large
oscillations which may result in failure of that part.
In S.H.M. acceleration is directly proportional to the displacement from the mean position and is
directed towards the centre.
(zx) Resonance : When the frequency of external force is equal to the natural frequency of a vibrating
body, the amplitude of vibration becomes excessively large. This is known as “Resonance” . At
resonance there are chances of machine part or structure to fail due to excessively large amplitude. It
is thus important to find natural freuqencies of the system in order to avoid resonance.
(x) Damping: It is resistance provided to the vibrating body and vibrations related to it are called
damped vibration.
(xi) Phase difference : Suppose there are two vectors
According to this method the sum of forces and moments acting on the system is zero if no external
force is applied on the system.
Consider fig. I
Q. 9. Classify different types of vibrations.
Non-linear vibrations : When amplitude of vibrations tends towards large value, then vibrations
become non-linear in nature. They do not obey law of superimposition. III. Damped and Undamped
vibrations
Damped vibrations are those in which amplitude of vibration decreases with time. These vibrations
are real and are also called transient vibrations.
Undamped vibrations are those in which amplitude of vibration remains constant. In ideal system
there would be no damping and so amplitude of vibration is steady.
Ans. When two harmonic motions pass through some point in a medium simultaneously, the resultant
is the sum of two motions. This superimposition of harmonics is called interference. When two
harmonics are in phase then their resultant amplitude is maximum and the resultant amplitude is
minimum when two harmonics are out of phase. This phenomenon continuously occurs i.e. amplitude
becomes maximum and minimum repeatedly. This is called “beats”. For beats to occur, the difference
in frequencies of two waves should be very less.
Maximum amplitude = 2A
Minimum amplitude 0.
Q. 11. Derive the relation for the work done by the harmonic force
Ans. Let harmonic force F = F0 sin cot is acting on a vibrating body having
motion
Q. 12. Add the following harmonic motions analytically and check the solution graphically.
Graphically:
Q. 14. Show that the resultant motion of three harmonic motions given below is zero.
Hence proved.
Q. 16. How do you add two harmonic motions having different frequencies?
Ans. Let two harmonic motions with slightly different frequencies be: -
Q. 17. How can we make a system vibrate in one of its natural mode?
Ans. When a system is displaced slightly from its equilibrium position and allowed to vibrate then
these are called free vibrations and the system is said to vibrate m its natural mode without any
external force impressed on it.
Q. 18. How does a continuous system differ from a discrete system in the nature of its equation
of motion?
Ans. Continuous systems have infinite degree of freedom and so the no. of solutions are infinite. The
equation of motion for continuous system involve both displacement (x) as well as time (t). Discrete
systems have finite degree of freedom and so the no. of solutions are finite. The discrete systems may
be single degree of freedom system, 2 degree freedom system and so on. The number of equations
depends upon the degree of freedom of discrete system. Further equation of motion of discrete
systems involve only position (x) and not time (t).
Ans. If the body vibrates with internal forces and no external force is included, it is Further during
vibrations if there is no loss of energy due to friction or resistance, it is known as undamped free
vibration.
Q. 2 Consider the relation for the frequency of spring mass system in vertical position.
Ans.
Q. 3. What is D’Alembert’s Principle?
Ans. D’Alembert’s principle states that if the resultant force acting on a body along with the inertia
force is zero, then the body will be in static equilibrium.
Inertia force acting on the body is given by
Assuming that the resultant force acting on body is F, then the body will be in static equilibrium if
Consider fig. 2.2., the spring force of the body Kx is acting upwards and acceleration of the body i is
acting in downward direction. The accelerating force is acting downward so inertia force is acting
upwards, so the body is
M static equilibrium under the action of the two forces Kx
and mi. Mathematically it can be written as
Ans. Consider a rotor having mass moment of inertia I connected at end of the shaft having torsional
stiffness KT and is rotated by an angle 0 as shown in fig. 2.3.
Ans. The system which is suspended vertically and oscillates with small amplitude under the action
of force of gravity is known as compound pendulum (Fig. 2.4)
Let W = Weight of rigid body
o = Point of suspension
k = Radius of gyration about an axis passing
through centre of gravity G.
h = Height of point of suspension frQm G.
I = Moment of Inertia of the body about 0.
I = + mh2 (Parallel axis theorem)
Q. 6. Find the natural frequency of the column of liquid contained in a simple a-Tube
manometer as shown in figure 2.5. Length of tube is 0.2 m.
will be x. The velocity of spring element at distance y from the fixed end is given by where 1
is the total length of spring.
Let p be the mass per unit length of spring element, the
Differentiating the above equation
Q. 8. Determine the natural frequency of spring mass pulley system as shown in Fig. 2.7.
Q. 9. A cylinder of diameter D and mass in floats vertically in a liquid of mass density p as
shown in Fig. 2.8. Find the period of oscillation if it is depressed slightly and released. .
Q. 10. Determine the frequency of oscillation of the system shown in Fig. 2.9.
Q. 11. Determine the natural frequency of spring controlled simple pendulum as shown in Fig.
2.10.
Ans. Let us say the system is displaced by an angle 0 to the right. Equation of motion can be written
as;
Q. 12. Determine the natural frequency of the system shown in Fig. 2.11.
Ans. Let m be the mass of circular cylinder and r be the radius of the cylinder.
Q. 14. A spring-mass system has a time period of 0.25 sec. What will be the new
time period if the spring constant is increased by 30%?
Ans. We know
Q. 15. A car is having a mass of 1000 kg and its spring gets deflected 3 cm under its own load..
Find the natural frequency of car in vertical direction.
Q. 16. A torsional pendulum has a rod of 5 mm diameter. Find out its length for natural
frequency of 10 Hz. The inertia of the mass fixed at the free end is 0.0120 kg rn2., Take G = 0.84
x 1011 N/m2.
Ans. The natural frequency of pendulum is given as
Q. 17. Find the natural frequency of the system shown in Figure 2.12.
Ans. Since the three springs are in parallel1 their equivalent sfess can be calculated
Q. 18. A mass is suspended from a spring system as shown in figure 2.13. Determine the natural
frequency of the system.
Ans. Since spring k2 and k3 are connected in parallel1 so their equivalent k is given as k = + k3.
Again k and k1 are connected in series, so the equivalent ke is given as
Q. 21. Determine the natural frequency of the system as shown in figure. 2.16.
Ans. Damping is the resistance offered by a body to the motion of a vibratory system.
The resistance may be applied to liquid or solid internally or externally At the start of the vibratory
motion the amplitude of vibration is maximum wkij6es on decreasing with time. The rate of
decreasing amplitude depends upon the amount of damping.
1. Viscous damping: When the system is allowed to vibrate in viscous medium the damping is called
viscous Viscosity is the property of the fluid by virtue of which it offers resistance to moment of
one over the other.
The force F required . to maintain the velocity
x of plate is given by:
The main components of viscous damper are cylinder, piston and viscous fluid.
The damping resistance depends upon pressure difference on both sides of piston in viscous medium.
The clearance is left between piston and cylinder walls. More the clearance, more will be the velocity
of piston and less will be the value of viscous damping coefficient.
Equation of Motion
Some of the energy is wasted in friction and amplitude of vibrations goes on decreasing. Such type of
damping is called coulomb damping.
The damping’force, F =
The amplitude decay is of exponential nature.
4. &on-linear, p or Interfacial damping : Machine elements are connected through various joints and
microscopic slip occurs over the joints of machine elements which usdisspoint of energy when
machine elements are in contact with fluctuating load. The energy dissipated per cycle depends upon
coefficient of friction, pressure at contacting surface and amplitude of vibration. There is an optimum
value of contact pressure at which energy dissipated is maximum for different amplitudes.
5. Eddy current damping : If a non-ferrous conducting object (e.g. plater d etc.) moves in a direction
perpendicular lines of magnetic flux is produced by current is induced in the object.1iiiiIrent is
proportional to vlocity of the object. The current induced is called eddy current which set up its own
magnetic field opposite to original magnetic field that has induced it. This provides resistance to
motion object It forms magnetic field . This type of damping produced by eddy currents is
called eddy current damping. it is used in vibrometers and in some vibration control
systems.
Q. 3. Derive the relation for energy dissipated in viscous damping per cycle.
Ans. Energy dissipated in viscous damping per cycle
Q. 4. Prove that frequency of vibration of system having coulomb damping is same as that of
undamped system.
Ans. Rate of Decay of oscillation: Let 1A be the amplitude of body from mean position to start and
after half cycle, let x be its amplitude. The velocity of mass =0 at two extreme positions. (Refer Fig.
3.9)
Therefore, total energy of the system at two extreme positions be
The difference between the two energies must be equal to energy dissipated or work done against
friction.
Q. 7. What is the response of single degree of freedom system with viscous damping when it is:
Depending upon the value of damping ratio e, the damped systems are categorized as:
This motion is also called a periodic motion. When t =0, x = A1 + A2. This system is non-vibratory
in nature. When once the system is disturbed, it will take infinite time to come back to the
equilibrium condition.
The values of A1 and A2 can be found by initial conditions.
The value of displacement x goes on decreasing with time.
In critical damping both roots are equal and are equal to - (0.
The solution of critically damped system is given as;
1
I.
The amplitude vary exponentially with time. As time increases amplitude decreases.
An underdamped system is an oscillatory system whose amplitude decreases with time. Theoretically
the system will never come to rest although the amplitude of vibration may be very very small.
Ans. Out of the three modes the vibrating body which has been displaced from its
mean position would come to state of rest in smallest possible time without overshooting i.e. without
executing oscillation about mean position in critical damping mode.
So critical damping is used for practical applications in large guns so that after firing the returning to
original position in minimum time without vibrating and ready for next firing without delay. If
damping provided is overdamped or underdamped, then there will be delay. This property is also
design of an instrument
A -, Max Amplitude
X5 -, Zero frequency deflection
the axis of rotation and centre of gravity is called eccentricity ‘e’ and mass acting at distance ‘e’ from
the axis of rotation is known as eccentric mass ‘rn0’.
Rotating Unbalance
The differential equation of motion can be written as:
Q. 6. Analyze the system having forced vibrations due to reciprocating unbalance.
Ans. For a reciprocating eccentric mass ‘m0’ inertia force is given by:
which is inertia force becomes rnjw2e sin wt which is same as that of revolving unbalance. Hence for
small value of ‘e’ analysis of rotating unbalance is applicable here also.
Q. 7. Derive that relation for displacement transmissibility in case of support
Ans. In case of locomotives or vehicles the wheels act as a base or support for the system. The wheels
can move up and down on road surface during motion of vehicle.
For a vehicle there is relative motion between wheels and chassis and wheels are
having relative motion w.r.t. road surface. The amplitude of vibration is proportional to speed of
vehicle and nature of road surface. In vibratory system where support is put to excitation both
absolute and relative motion become important.
Here
Therefore
is called displacement transmissibility.
Displacement Transmissibility It is the rajc of the magnitude body to the amplitude of support.
Q. 8. Derive the response of the system in which mass is having relative motion with respect to
support.
Ans. Let us assume that z is the relative motion/displacement of mass with respect to support.
Therefore;
Equation of motion of absolute motion was;
It becomes;
Q. 9. What is vibration isolation ? What are the commonly used materials for vibration
analysis.
Ans. The high speed engines and machines when mounted on foundation support cause vibrations of
excessive amplitudes because of unbalance forces that are set up during its working. The high
amplitudes of vibration can damage the foundation and so the vibrations transmitted to the foundation
should be eliminated or reduced as far as possible. There are certain devices like springs, dampers etc.
which reduce the transmission of vibrations to the foundation and are called vibration isolators. This
process of reducing the transmission of vibrations to the foundation is called vibration isolation.
Lesser is the amount of force/ or motion transmitted to the foundation, greater is the vibration
isolation. Materials most commonly used for vibration isolation are ; rubber, felt, cork, metallic
springs etc. These vibration absorbers are put between the vibrating body and the foundation support.
Ans. Transmissibility
The resultant of spring force and damping force
Mathematically :
We know that,
Vibrometer/Accelerometer
The relative motion of mass ‘m’ w.r.t. vibrating body is converted into voltage and
is recorded on paper placed on the drum. Since
Since natural frequency of the accelerometer is very high i.e. is high, therefore, it is very
light in construction.
Where :
If natural frequency a for the accelerometer remains constant, then ; Z Acceleration of vibrating body
i.e. Relative amplitude of mass ‘m’ w.r.t. vibrating body is proportional to acceleration of vibrating
body.
Hence voltage signal obtained on. the rotating drum will be proportional to acceleration of vibrating
body. The accelerometer with 100 Hz natural frequency will have frequency range from 0 — 25 Hz at
e = 0.7 and will provide very accurate results.
Q. 12. What is quality factor and half power points ? Also define bandwidth.
Ans. Quality Factor and Half Power Points:
The amplitude ratio at resonance i.e.
Ans.
Where
Q. 14. What is the principle of frequency measuring devices ? Explain the working of any two
such devices.
Ans. Frequency Measuring Devices : The working of frequency measuring instruments is based on
resonance. At resonance the amplitude of vibration is maximum and the natural frequency of system
is equal to the excitation frequency
1. Fullarton Tachometer/Single Reed Instrument. It consists of strip carrying mass ‘m’ at its
free end. The strip is treated as cantilever the length of which an be changed by means of
screw mechanism
The strip of the instrument is pressed over the vibrating body to find its natural frequency. The length
of strip is adjusted till resonance takes place i.e. amplitude of vibration becomes maximum At
resonance natural frequency of strip becomes equal to the frequency of éxcitatioñ e frequency of
vibrating body)
The frequency for cantilever carrying mass m’ at end and of length ‘1’ is given by;
2. Frahm Tachometer/Multi reed instrument. It consists of several reeds with known natural
frequencies (711 different). Small difference in natural frequencies of reed will show re accurate
results. The instrument is brought in contact with vibrating body whose frequency is to be measured.
One of the reeds will vibrate with maximum amplitude hence that reed will show the frequency of
vibrating body.
We know
The static deflection of reed considering it to be cantilever with mass ‘m’ at one
end;
Ans. Critical Speed : When the natural frequency of the system coincides with external forcing
frequency lit f vibration is maximum and this condition is known as resonance. The speed at which
resonance occurs is called critical/whirling speed. At critical speeds the amplitude of vibration of
rotors is excessive and large amount of force is transmitted to foundation or bearings At critical speed
the system mav7iidue to excessive amplitude. 1tisyery important to find natural frequency of shaft to
avoid occurs of resonance at critical speeds and thus prevent excessive noise and breakage Critical
speed may occur because of eccentric mounting rotor, non-uniform distribution of rotor material,
bending of shaft etc.
Q. 16. Prove that
At equilibrium:
Where
From (I)
Considering damping :
Q. 17. A vibrating body having mass 1 kg is suspended by a spring of stiffness 1000 N/rn and it
is put to harmonic excitation of 10 N. Assuming viscous damping, determine;
(a) the resonant frequency
(c) amplitude at resonance
(b) phase angle at resonance
(d) frequency corresponding to peak amplitude
(e) damped frequency.
Q. 18. The total mass of the system having rotating unbalance is 25 kg. At speed of 1000 rpm,
the system and the eccentric ma have a phase angle of 90° and the corresponding amplitude is
1.5 cm. The eccentric unbalance mass of 1 kg has radius of rotation 4 cm. Determine:
(a) Natural frequency of the system
(b) The damping factor
(c) The amplitude at 1500 rpm
(d) The phase angle at 1500 rpm.
Ans.Given :
At phase angle 90°, the condition of resonance will occur i.e. w =Wc
Q. 19. The weight of an electric motor is 125 N and it runs at 1500 rpm. The armature weighs
35 N and its centre of gravity lies 0.05 cm from the axis of rotation. The motor is mounted on
five springs of negligible damping so that force transmitted is one-eleventh of the impressed
force. Assume that the weight of motor is equally distributed among the five springs.
Determine:
(a) Stiffness of each spring
(b) Dynamic force transmitted to the base at operating speed
(c) Natural frequency of the system.
Q. 20. The springs of an automobile trailer are compressed 0.1 m under its own weight. Find
the critical speed when the trailer is passing over a road with a profile of sine wave whose
amplitude is 80 mm and the wavelength is 14 m. Find the amplitude of vibration at speed of 60
km/hr.
Let us assume the critical speed of the trailer as Vm/sec
Q. 21. The damped natural frequency of a system as obtained from a free vibration test is 9.8
c.p.s. During the forced vibration test, with constant excitation force on the same system the
maximum amplitude of vibration is found to be 9.6 c.p.c. Find the damping factor for the
system and its natural frequency.
Ans.
Q. 24. A rotor of mass 1’2 kg is mounted in the middle of 25 mm diameter shaft supported
between two bearings placed at 900 mm form each other. The rotor is having 0.02 mm
eccentricity. If the system rotates at 3000 rpm, determine the amplitude - of steady state
vibrations and the dynamic force on the bearings. -Take E = 2 x i05 N/mm2
Ans. Let us assume the shaft simply supported, its stiffness is given by:
The negative sign indicates that the displacement is out of phase with centrifugal force
Dynamic load on bearings :
Q. 25. An air compressor of 450 kg operates at constant speed of 1750 r.p.m. Rotating parts are
well balanced. The reciprocating part is 10 kg and crank radius is 100 mm. The mounting
introduces a viscous damping of damping factor 0.15. Specify the spring for the mounting such
that only 20% of the unbalanced force is transmitted to the foundation. Find out the amplitude
of transmitted force.
We know that
Q. 26. A vibrating body is supported by six isolators each having stiffness 32000 N/m and 6
dashpots having damping factor as 400 N-sec/m. The vibrating body is to be isolated by a
rotating device having an amplitude of 0.06 mm at 600 rpm. Take m3Okg. -
Determine: .
(a) Amplitude of vibration of the body -
(b) Dynamic load on each isolator due to vibration.
Given
We know that
Q. 28. A vibratory body of mass 150 kg-supported on springs of total stiffness 1050 kN/m
has a rotating unbalanced force of 525 N at a speed of 6000 r.p.m.
If the damping factor is 0.3, determine (a) The amplitude caused by the unbalance and its
phase angle, (b) The transmissibility, (c) The actual force transmitted and its phase angle.
Ans.
Q. 1.What are the two degree of freedom system?
Ans. The system which requires two co-ordinates to describe its motion completely is called two
degree of freedom system. In a two degree of freedom system there are two masses which have two
natural frequencies and two co-ordinates are required to specify the configuration of the system
completely.
Ans. In a two degree freedom system there are two natural frequencies of the system. The system at
its lowest or first natural frequency its first and next higher i.e. second natural frequency is called its
second mode. If the two masses vibrate at same frequency and in phase it is called principal mode of
vibration. If prncipa1 mode of vibration the amplitude of one of the masses is then it is known as
normal mode of vibration.
Ans.
Torsional Vibrations : Consider fig. 5.2. A shaft AB is carrying two rotors of moment of inertia I and
‘2 Let and °2 be the angular displacements of rotor at any .instant from mean position. The equation
of motion can be written s,
Put,
Solving by determinant
From (VIII)
It shows that the angular displacements of rotors are inversely proportional to their inertia.
The section of the shaft where angular displacement is zero Is known as node. First Mode shape
Ans. Semi-Definite Systems : The system having one of their natural frequencies equal to zero are
known as semi-definite systems. The example of the type of system is when two masses m1 and m2
are connected by spring K
Q. 5. What is co-ordinate coupling? Determine the natural frequencies of such system
with dynamic coupling? (V.V. Imp.)
These are uncoupled differential equations and when then it is called dynamic coupling.
The natural frequencies of the system are:
Q. 6. What are vibration absorbers ? Prove that spring force of the absorber system is equal
and opposite to the excitition force for main system to be stationary?
Ans.Vibration Absorber. When a structure which is excited by an external harmonic force has
undesirable vibrations, it becomes necessary to eliminate them by coupling some vibrating system to
it. The vibrating system is known as vibration absorber or dynamic vibration absorber. Vibration
absorbers are used to control the structural resonance (consider the main figure)
The natural frequency of this system is
Equations of Motion
Where
Hence when the amplitude A1 = 0 i.e. main system becomes stationary the spring force
of the absorber is equal and opposite to exciting force. The energy of the main system is absorbed by
vibration absorber which is also called auxiliary system.
Amplitude of the auxiliary system is inversely proportional to spring constant ‘K2’.
This equation is used for design of absorber.
Q.7. Discuss the effect of mass ratio on natural frequency of the vibration absorber.
Ans. Demerits of Dynamic vibration Absorber : Th dynamic vibration absorber whether for the
rectilinear torsional system is fully effective at a particular impressed frequency for which it is
designed This means that main system will be stationary only for particular frequency. Thus dynamic
vibration absorbers are effectivefor constant speed machine but lose their effectiveness with any
change in speed of machines. Most rotors are likely to run throw’ wide range speeds so dynamic
vibrations absorbers become ineffective.
Q. 8. (ii) Prove that all frequency of centrifugal pendulum absorber is always proportional to
the speed of rotating body.
Ans. Centrifugal Pendulum Absorber: It is effective at all speeds of rotation and is improvement
over conventional dynamic vibration absorbers. A pendulum PB of length ‘L’ is attached to rotating
member at point P which is at radius ‘R’ from centre of rotation ‘O’. The mass of bob of pendulum is
‘m’ and string is assumed to have a negligible mass. The pendulum is subjected to centrifugal force
which is neglected. The body is rotating with angular velocity ‘w’ rad/s and of centrifugal force mw2r
is experienced by bob of the pendulum. at radius ‘r’ from 0.
Ans. Order No: The torsional system receives certain number of torques per revolution. The no. of
these disturbing torques per revolution Is known as order no. of the system
2-cylinder engine working on 4-stroke - Order No. = 1
4-cylinder engine working on 4-stroke - Order No. = 2
6-cylinder engine working on 4-stroke - Order No. 3
Design of centrifugal pendulum absorber
For pendulum absorber to be effective its natural frequency must be equal to excitation
frequency or frequency of disturbing torques.
Ans. (A) Untuned Dry friction damper or Untuned vibration Absorber (Lanchester Damper) :
This type of damper is very advantageous to use for torsional vibrations near resonance conditions. It
consists of two fly wheels mounted freely over a hub. The hub is rigidly fixed to shaft undergoing
vibrations. There are friction plates attached to the extension of the hub. These friction plates apply
pressure on the flywheel and are responsible for driving the flywheel.
When the pressure. between the friction plates and flywheel is zero the relative velocity is maximum
but frictional torque is zero. There is no energy dissipation in such case. When the pressure between
the friction plate and flywheel is large due to large friction torque there is no relative velocity
between flywheel and shaft and energy dissipation is zero.
When the speed of the main system is such that torsional vibrations are present in the system then the
pressure between the friction material and flywheel is such that both frictional torque and relative
rubbing is present then there is dissipation of energy in the absorber which causes, reduction in
amplitude of the vibrations of the man system.
(B) Untuned Viscous damper (Houdaille Damper) : this types of damper is similar in principle to
the Lanchester Damper except that instead of using friction plates for dry friction damping, this
system uses friction damping. It consists of a freely rotating disc enclosed in the close-fitting case
which is keyed to the shaft. Normally the disc rotates at the shaft speed owing to the viscous drag of
the oil between the disc and the case. However if the shaft vibrates torsionally, viscous action of the
oil between the disc and casing gives a damping action.
Q. 10. Determine the two natural frequencies of vibration and the ratio of the amplitudes of
motion of mass m1 and m2 for the system shown in Fig. 5.11.
Q. 11. Solve the problem shown in Fig. 5.12; m1 10 kg, m2 = 15 kg, k = 320.N/m.
Q. 12. A vibratory system performs the motions as expressed by the following equations:
If the system is turned through 1.5 radians and released, find the frequencies and mode shapes
Q. 13. A machine runs at 5000 rpm. Its forcing frequency is very near to its natural frequency.
If the nearest frequency of the machine is at least 20% from the forced frequency, design a
suitable vibration absorber for the system. Assume the mass of the machine as 30 kg.
Resolving the forces horizontally, T sin 0 will be known as restoring force as it downwards and
brings to its original state. Horizontal displacement of
Consider forces for mass rn1. All the forces are acting horizontally,
Q. 15. Find the natural frequencies of the there is no slip between cord and cylinder.
system shown in Fig. 5.14. Assume that
Ans. Let us give x vertical displacement to mass as shown. Since there is no slip between the cord
and cylinder, so vertical displacement x causes the cylinder to rotate by angle 0.
Writing the equations
Substituting these values in the above equations
The middle of equivalent shaft is 20.72 cm from the left hand side.
Q. 18. Find the natural frequency of the system shown in Fig 5.17.
Q. 19. Derive the natural frequencies of the system shown in Fig. 5.19.
Ans. The equations of motion for the system shown in figure can be written as
Rearranging the above equations, we can write them as
Q. 20. Two rotors A and B are attached to the end of a shaft 50 cm long. Weight of rotor A is
300 N and its radius of gyration is 30 cm and the corresponding values of B are 500 N and 45
cm respecitvely. The shaft is 7cm in diameter for first 25 cm, 12 cm in diameter for next 10 cm
and 10 cm diameter for remaining length. Modulus of rigidity for shaft material is 8 x 106
kg/cm2 Find:
(i)the position of node and
(ii) the frequency of torsional vibrations.
Let N be the position of node for the two rotor system and the length of two parts of equivalent shaft
be 1A and 1B as shown in Fig. 5,21.
We know that,
From equations (i) and (ii), we get
Ans. In a two degree freedom system, any point in the system may execute harmonic of the two
natural frequencies and these are known of vibration. Let us assume the motion of two masses is
simple harmonic and is represented as
where X1 and X2are the amplitudes of two masses respectively and are referred as
principal co-ordinal.
Q. 22. Derive the equation of motion of the system shown in figure below and find its
frequencies.
Ans.
The frequency equation can be written as
Q. 24. Calculate the natural frequency of a shaft of diameter 10 cm and length 300 cm carrying
two discs of diameters 125 cm and 200 cm respectively at its ends and weighing 480 N and 900
N respectively. Modulus of the rigidity of the shaft may be taken as 2 x 1011 N/m2.
Ans.
Q. 25. What is the difference between a vibration absorber and a vibration isolator?
Ans. Vibration absorber is a s ring mass system attached to the main vibratory system to absorb the
vibrations whereas vibration isolators are material like cork , rubber, felt, pad etc. which are used to
isolate machines from its foundation and support. These vibration isolation absorb the shocks forces
set up in the machinery and prevents the damage of foundations and supports.