Professional Documents
Culture Documents
Arthroscopy of The Temporomandibular Joint
Arthroscopy of The Temporomandibular Joint
ARTHROSCOPY OF THE
TEMPOROMANDIBULAR JOINT
Wolfram M. H. Kaduk
®
ARTHROSCOPY OF THE
TEMPOROMANDIBULAR JOINT
Prof. Wolfram M. H. KADUK, MD, DDS
In case any references are made in this booklet to any 3rd party
publication(s) or links to any 3rd party websites are mentioned, it is made
clear that neither the publisher nor the author or other copyright holders
of this booklet endorse in any way the content of said publication(s)
and/or web sites referred to or linked from this booklet and do not
assume any form of liability for any factual inaccuracies or breaches
of law which may occur therein. Thus, no liability shall be accepted for
content within the 3rd party publication(s) or 3rd party websites and no
guarantee is given for any other work or any other websites at all. ISBN 978-3-89756-122-9
Arthroscopy of the Temporomandibular Joint 5
Table of Contents
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.0 Introduction
The surgical treatment of temporomandibular joint (TMJ) As in all degenerative muscle, bone and joint diseases,
disorders presents us with an extremely complex and surgical intervention should be elected sparingly and
complicated set of interwoven problems that can raise the primary treatment options are conservative. Surgical
difficult issues of diagnosis and treatment. treatment is indicated in only about 5% of patients
The great diversity of TMJ disorders results from the with TMJ disorders. Because TMJ operations are such
overlap between multiple organ systems and numerous specialized procedures, often it takes years to acquire
functional processes, as illustrated in Fig. 1. adequate clinical experience.
Immediate manual reduction (aided by local anes- Permanent correction to a centric jaw position
thesia, intravenous sedation, or general anesthesia (the painless or least painful position of the mandible)
with muscle relaxation). should be considered at this stage as an alternative
Next: 3 months of conservative therapy (physical to life-long splint therapy. Options for permanent
therapy, determining and establishing the centric correction include orthognathic surgery, prosthetic
position of the TMJ, splint therapy, pharmacologic treatment, and dysgnathic surgery.
therapy).
If the TMJ disorder has not improved or is worse by
After an unsuccessful 3-month trial of conser- 12 months after the initial arthroscopic procedure,
vative therapy: reduction under arthroscopic control, we recommend further arthroscopic treatment
arthroscopic shortening of the retrodiscal tissue. or even open surgery (e.g., open shortening of the
Conservative treatment is continued for up to one retrodiscal tissue)).
year after arthroscopic surgery, including the use of
centric splints that protect the TMJ or widen the joint If the TMJ is not permanently corrected to a centric
space (e.g., a bite guard that moves the mandible position, it is extremely likely that the TMJ changes
1.5 – 2 mm forward). Myoarthropathy may be treated will recur and that surgical measures on the disc and
if necessary by injecting botulinum toxin into the retrodiscal tissue will be unsuccessful. We believe that
affected musculature (e.g., the lateral pterygoid the timely initiation of appropriate treatment can reduce
muscle). the incidence of serious TMJ disorders.
8 Arthroscopy of the Temporomandibular Joint
2
Draping for TMJ arthroscopy.
Arthroscopy of the Temporomandibular Joint 9
1 Locate and mark the center of the tragus. Puncturing the Joint:
2 Locate and mark the lateral canthus of the eye. At point A (Fig. 3): Insert the sharp obturator/trocar
assembly to the temporal bone, angling it medially
3 Draw a straight line between the center of the
upward. While keeping the obturator tip in contact with
tragus and the lateral canthus.
the bone, advance it approximately 2.5 cm into the upper
4 Measure and mark a point on the line that is joint space, then remove the obturator.
10 mm from the center of the tragus, and mark
Check the correct placement of the trocar in the joint
a point (A) located 2 mm below it. The trocar
space by infusing irrigation fluid through the arthroscope
with obturator will be inserted at that point, and
sheath (trocar) and passively opening and closing the
the obturator will be removed for insertion of the
mandible. If the fluid level in the arthroscope sheath
arthroscope.
moves with the jaw, this confirms that the trocar is safely
5 Measure and mark a point on the original line that in the joint space. Now introduce the arthroscope with
is 20 mm from the center of the tragus. Drop a attached video camera (remember to perform the white
perpendicular at that point, measure balance!) into the sheath, and connect the irrigation line
10 mm down from the line, and mark that point to the arthroscope sheath.
(B). That is the site where the trocar with sharp
At point B (Fig. 3): Insert the second sharp obturator
obturator will be introduced (Fig. 3).
at point B with the tip of the obturator angled upward.
Direct it toward the tip of the arthroscope trocar and
advance it until it is in contact the temporal bone of
Before inserting the trocars, we palpate the TMJ region the glenoid fossa. Keeping the obturator tip in contact
and move the joint to confirm that the points have been with the bone, advance it approximately 2.5 cm into the
marked correctly, since some distortion may occur due upper joint space, then remove the obturator.
to shifting of the skin.
Check the correct placement of the arthroscope sheath
in the joint space by infusing irrigation fluid through
the access port and passively opening and closing
the mandible. The fluid level in the arthroscope sheath
should move with the jaw, confirming that the sheath is
correctly positioned in the joint space.
10 Arthroscopy of the Temporomandibular Joint
Next open the inflow stopcock on the arthroscope Another technique for puncturing the upper joint space
sheath, which is connected to an infusion system. If is to use a blunt obturator after filling the upper compart-
continuous irrigation is obtained with an inflow pressure ment with fluid injected through a hypodermic needle.
of approximately 1000 mm H2O and there is a good To avoid injuring the disc and retrodiscal tissue, we track
reflux of irrigation liquid through the sheath, an infusion the sharp point along the bone of the glenoid fossa,
extension tubing can be connected to the arthroscope working our way around the lateral rim of the fossa until
sheath (to direct the fluid to a collection vessel), and we feel the point “fall” into the joint space. Histologic
diagnostic arthroscopy may begin. studies in animal models show that a fine scratch in the
bone of the lateral glenoid rim will heal completely with
no adverse sequelae for the joint.
The outflowing fluid is collected in the vessel and may
be discarded or be retained for diagnostic testing. After Since distending the joint space with fluid may sometimes
the operating room lights are turned off, the surgeon result in a faulty puncture, an alternative method is to pull
proceeds with indirect diagnostic TMJ arthroscopy while the lower jaw forward and downward to open up the joint
watching the video monitor. space.
4a 4b
After introducing the arthroscope, the surgeon establishes orientation
in the TMJ by watching the video monitor while manually opening the
patient’s mouth.
Arthroscopy of the Temporomandibular Joint 11
1 Landmarks are needed for recognizing and Arthroscopic “red-out” due to insufficient lavage.
7a 7b 7c
Arthroscopic view of a stage II disc View of the articular tubercle and underlying View of the hyperplastic retrodiscal tissue (c).
placement. The junction of the disc and disc (a, b).
retrodiscal tissue is below the tubercle;
normally it should lie farther back in the
joint.
Arthroscopy of the Temporomandibular Joint 13
Stage II
Stage III
9a 9b
Arthroscopic appearance of the retrodiscal tissue and medial Schematic representation of the stages of anterior disc displacement.
articular surface at various stages of disc displacement and
associated hyperplasia and elongation of the retrodiscal tissue.
14 Arthroscopy of the Temporomandibular Joint
10
Shortening the retrodiscal tissue with a water-jet scalpel:
a Locating the retrodiscal tissue,
b Appearance after treatment with the water-jet scalpel.
The water jet causes the retrodiscal tissue to swell, producing
an immediate shortening effect. This effect is perpetuated by
subsequent scarring of the tissue.
Arthroscopy of the Temporomandibular Joint 15
11
Use of the Nd:YAG laser (arrow) in the TMJ.
16 Arthroscopy of the Temporomandibular Joint
13
Correlation between MRI and arthroscopy with a surgical navigation
system.
Arthroscopy of the Temporomandibular Joint 17
The first TMJ arthroscope with an integrated working general anesthesia (Kaduk et al. 2003) with the goal of
channel was produced by KARL STORZ in 2009. The answering the following questions:
system was initially tested in experimental animals under
1 Is the new arthroscope stable enough to pierce the 4 Can the integrated irrigation channel provide for
TMJ capsule and meet the functional requirements continuous irrigation of the joint space?
of TMJ arthroscopy? 5 Does the integrated working channel of the
2 Is the handling of the arthroscope satisfactory, new TMJ arthroscope allow for the easy,
precise handling and guidance of instruments
and is the outer diameter of the endoscope small
(probe, laser fiber, water-jet scalpel)?
enough for insertion into the joint?
6 Can the new endoscope be maneuvered through
3 Is the endoscopic image resolution or video the joint space by surgical navigation, for example,
quality adequate for evaluating the TMJ and guiding and are all intra-articular structures accessible via
instrument use within the joint space? the arthroscope?
The results of the experimental studies have shown had to be reduced to make room for the extra channel.
that the TMJ arthroscope with integrated working and As a result, the resolution of the new device is less than
irrigation channels does have adequate stability, despite that of traditional TMJ arthroscopes. The decreased
the fact that its outer diameter is limited to 2.3 mm by resolution did not prove to be a problem during practical
anatomical constraints. Even when piercing the TMJ work with the arthroscope, however. As Fig. 16a–c
capsule, the arthroscope showed no instability or other illustrates, the image quality is fine for evaluating the
design-related problems. The 2.3-mm outer diameter intra-articular structures and using instruments through
could enter the joint space as easily as a conventional the integrated working channel.
arthroscope with an outer diameter of 2.0 mm. Irrigating the joint at a pressure of 1000 mm H2O with an
Because the arthroscope shaft, with its 2.3-mm diameter, infusion system was sufficient to maintain a clear image
had to accommodate the integrated working channel in throughout the procedure.
addition to optical fibers, the number of optical fibers
18
Three-dimensional CT image displays the close anatomic relationship
among the TMJ, the external auditory canal, and the middle and inner
ear. This underscores the potential value of navigation-assisted TMJ
arthroscopy in preventing complications.
Arthroscopy of the Temporomandibular Joint 21
The TMJ arthroscope with integrated working channel capabilities that could be useful for other applications
offers advanced technical possibilities for arthroscopic in oromaxillofacial surgery, facial plastic surgery, and
surgery. For example, it is conceivable that two of these otorhinolaryngology such as paranasal sinus endoscopy.
endoscopes could be introduced into the joint space to The inherently larger endoscope diameter also helps to
facilitate arthroscopic suturing techniques. Moreover, the simplify design and manufacturing.
integrated working channel provides enhanced technical
58705 AA HOPKINS® Straight Forward Telescope 0°, diameter 1.9 mm, length 6.5 cm,
autoclavable, fi
ber optic light transmission incorporated, color code: green
58706 AN High Flow Arthroscope Sheath, diameter 2.5 mm, working length 4 cm,
for use with HOPKINS® Telescope 0°, 58705 AA, color code: green
58705 BA HOPKINS® Forward-Oblique Telescope 30°, diameter 1.9 mm, length 6.5 cm,
autoclavable, fi
ber optic light transmission incorporated, color code: red
58706 BN High Flow Arthroscope Sheath, diameter 2.5 mm, working length 4 cm,
for use with HOPKINS® Telescope 30°, 58705 BA, color code: red
58706 BS Obturator, sharp, for use with Arthroscope Sheaths 58706 AN/BN
58706 BT Obturator, blunt, for use with Arthroscope Sheaths 58706 AN/BN
58717 X Trocar, diameter 1.8 mm, length 4 cm, for use with 58717 XB/XS
58717 XS Obturator, sharp, for use with Trocar 58717 X
58717 XB Obturator, blunt, for use with Trocar 58717 X
58717 PZ Biopsy Forceps, single-action jaws, diameter 1.3 mm, length 6 cm
58702 EO Scissors, upbiting, diameter 2 mm, working length 10 cm
58702 EK Scissors, downbiting, diameter 2 mm, working length 10 cm
58702 DH Forceps, through-cutting, diameter 2 mm, working length 10 cm
58702 U Grasping Forceps, diameter 2 mm, working length 10 cm
58702 M Knife, bayonet-shaped, diameter 1.5 mm, working length 7.5 cm
58702 N Sickle Knife, diameter 1.5 mm, working length 7.5 cm
58702 S Palpation Hook, graduated, diameter 1.5 mm, length of hook 1 mm,
working length 7.5 cm
58702 W Changing Rod, for sheaths and trocars, length 15 cm
58702 X Trocar, diameter 2.5 mm, length 3.5 cm, for use with instruments 58702 M/N/S
58702 XS Obturator, sharp, for use with Trocar 58702 X
58702 XT Obturator, blunt, for use with Trocar 58702 X
It is recommended to check the suitability of the product for the intended procedure prior to use.
Arthroscopy of the Temporomandibular Joint 25
58717 PZ
11580 B Metal Tray, for sterilization and storage of one Miniature Straight
Forward Telescope 11575 A, 11581 A, 11582 A or 11583 A,
11578 A, perforated, lid with silicone bridges, with port for irrigation
connector, external dimensions (w x d x h): 275 x 178 x 35 mm
30 Arthroscopy of the Temporomandibular Joint
Innovative Design
## Dashboard: Complete overview with intuitive ## Automatic light source control
menu guidance ## Side-by-side view: Parallel display of standard
## Live menu: User-friendly and customizable image and the Visualization mode
## Intelligent icons: Graphic representation changes ## Multiple source control: IMAGE1 S a llows
when settings of connected devices or the entire the simultaneous display, processing and
system are adjusted documentation of image information from
two c onnected image sources, e.g., for hybrid
operations
TC 200EN
Specifications:
HD video outputs - 2x DVI-D Power supply 100 – 120 VAC/200 – 240 VAC
- 1x 3G-SDI Power frequency 50/60 Hz
Format signal outputs 1920 x 1080p, 50/60 Hz Protection class I, CF-Defib
LINK video inputs 3x Dimensions w x h x d 305 x 54 x 320 mm
USB interface 4x USB, (2x front, 2x rear) Weight 2.1 kg
SCB interface 2x 6-pin mini-DIN
TC 300
Specifications:
Camera System TC 300 (H3-Link)
Supported camera heads/video endoscopes TH 100, TH 101, TH 102, TH 103, TH 104, TH 106
(fully compatible with IMAGE1 S)
22 2200 55-3, 22 2200 56-3, 22 2200 53-3, 22 2200 60-3, 22 2200 61-3,
22 2200 54-3, 22 2200 85-3
(compatible without IMAGE1 S technologies CLARA, CHROMA, SPECTRA*)
LINK video outputs 1x
Power supply 100 – 120 VAC/200 – 240 VAC
Power frequency 50/60 Hz
Protection class I, CF-Defib
Dimensions w x h x d 305 x 54 x 320 mm
Weight 1.86 kg
Specifications:
IMAGE1 FULL HD Camera Heads IMAGE1 S H3-Z
Product no. TH 100
Image sensor 3x 1/3" CCD chip
Dimensions w x h x d 39 x 49 x 114 mm
Weight 270 g
Optical interface integrated Parfocal Zoom Lens,
f = 15 – 31 mm (2x)
Min. sensitivity F 1.4/1.17 Lux
Grip mechanism standard eyepiece adaptor
Cable non-detachable
Cable length 300 cm
Specifications:
IMAGE1 FULL HD Camera Heads IMAGE1 S H3-ZA
Product no. TH 104
Image sensor 3x 1/3" CCD chip
Dimensions w x h x d 39 x 49 x 100 mm
Weight 299 g
Optical interface integrated Parfocal Zoom Lens,
f = 15 – 31 mm (2x)
Min. sensitivity F 1.4/1.17 Lux
Grip mechanism standard eyepiece adaptor
Cable non-detachable
Cable length 300 cm
34 Arthroscopy of the Temporomandibular Joint
Monitors
9619 NB 19" HD Monitor,
color systems PAL/NTSC, max. screen
resolution 1280 x 1024, image format 4:3,
power supply 100 – 240 VAC, 50/60 Hz,
wall-mounted with VESA 100 adaption,
including:
External 24 VDC Power Supply
Mains Cord
9619 NB
9826 NB
Arthroscopy of the Temporomandibular Joint 35
Monitors
Optional accessories:
9826 SF Pedestal, for monitor 9826 NB
9626 SF Pedestal, for monitor 9619 NB
Specifications:
KARL STORZ HD and FULL HD Monitors 19" 26"
Desktop with pedestal optional optional
Product no. 9619 NB 9826 NB
Brightness 200 cd/m2 (typ) 500 cd/m2 (typ)
Max. viewing angle 178° vertical 178° vertical
Pixel distance 0.29 mm 0.3 mm
Reaction time 5 ms 8 ms
Contrast ratio 700:1 1400:1
Mount 100 mm VESA 100 mm VESA
Weight 7.6 kg 7.7 kg
Rated power 28 W 72 W
Operating conditions 0 – 40°C 5 – 35°C
Storage -20 – 60°C -20 – 60°C
Rel. humidity max. 85% max. 85%
Dimensions w x h x d 469.5 x 416 x 75.5 mm 643 x 396 x 87 mm
Power supply 100 – 240 VAC 100 – 240 VAC
Certified to EN 60601-1, EN 60601-1, UL 60601-1,
protection class IPX0 MDD93/42/EEC,
protection class IPX2
36 Arthroscopy of the Temporomandibular Joint
Workflow-oriented use
Patient
Entering patient data has never been this easy. AIDA seamlessly
integrates into the existing infrastructure such as HIS and PACS.
Data can be entered manually or via a DICOM worklist.
ll important patient information is just a click away.
Checklist
Central administration and documentation of time-out. The checklist
simplifies the documentation of all critical steps in accordance with
clinical standards. All checklists can be adapted to individual needs
for sustainably increasing patient safety.
Record
High-quality documentation, with still images and videos being
recorded in FULL HD and 3D. The Dual Capture function allows for
the parallel (synchronous or independent) recording of two sources.
All recorded media can be marked for further processing with just
one click.
Edit
With the Edit module, simple adjustments to recorded still images
and videos can be very rapidly completed. Recordings can be quickly
optimized and then directly placed in the report.
In addition, freeze frames can be cut out of videos and edited and
saved. Existing markings from the Record module can be used for
quick selection.
Complete
Completing a procedure has never been easier. AIDA offers a large
selection of storage locations. The data exported to each storage
location can be defined. The Intelligent Export Manager (IEM) then
carries out the export in the background. To prevent data loss,
the system keeps the data until they have been successfully exported.
Reference
All important patient information is always available and easy to access.
Completed procedures including all information, still images, videos,
and the checklist report can be easily retrieved from the Reference module.
38 Arthroscopy of the Temporomandibular Joint
Equipment Cart
UG 540
40 Arthroscopy of the Temporomandibular Joint
UG 310
UG 410
UG 510
Arthroscopy of the Temporomandibular Joint 41
Notes:
42 Arthroscopy of the Temporomandibular Joint
Notes:
with the compliments of
KARL STORZ — ENDOSKOPE