Professional Documents
Culture Documents
C995N5C.QSK60 English
C995N5C.QSK60 English
995 kW - 1400 kW
Description Features
This Cummins Power Generation gas generator set Exhaust emissions – Lean burn technology provides
3
is a fully integrated power generation system exhaust emissions levels as low as 250 mg/Nm (0.5 g/hp-hr)
utilizing state of the art technology that results in NOx.
optimum performance and efficient use of fuel for ®
Cummins high efficiency gas engine – State of the art
continuous duty, CHP and peaking applications. lean burn engine utilizes Miller cycle combustion and full
authority electronic engine management system that provides
This generator set is designed in low emissions and high efficiency.
facilities certified to ISO 9001 and Permanent magnet generator (PMG) – Excitation system
manufactured in facilities certified to offers enhanced motor starting and fault clearing short circuit
ISO 9001 or ISO 9002.
capability.
The Prototype Test Support (PTS) Alternator – Several alternator sizes offer selectable voltage
program verifies the performance and temperature rise with low reactance 2/3 pitch windings;
integrity of the generator set design. low waveform distortion with non-linear loads, fault clearing
short circuit capability, bearing and stator RTDs, anti-
condensation heater, class F or H insulation (see alternator
datasheet for details). Mechanically strengthened for use on
utility paralleling with unreliable grid.
Control system – The PowerCommand 3.3 generator set
control is standard equipment and provides total genset
system integration including full paralleling capability in grid or
load share mode, precise frequency and voltage regulation,
alarm and status message display, AmpSentry™ protection,
output metering, auto-shutdown at fault detection and a user
interface panel installed onto the genset. Optional remote
operator panels are also available.
Cooling system – The generator set is equipped with the
capability to interface with a remote radiator or heat
exchanger.
Warranty and service – Backed by a comprehensive
warranty and worldwide distributor network that can provide all
levels of service from replacement parts to performance
guarantee programs.
50 Hz 60 Hz
New Old New Old
Model Model kW Configuration Model Model kW Configuration
C995 N5C None 995 4 pole direct drive
C1200 N5C None 1200 4 pole direct drive C1000 N6C GQKB 1000 6 pole direct drive
C1400 N5C GQKC 1400 4 pole direct drive C1100 N6C GQKC 1100 6 pole direct drive
* Genset is capable of operating between 0.8 lagging and 1.0 power factor. All fuel consumption and heat balance data is at 1.0 power factor.
* Listed ratings are for continuous grid parallel applications. Contact ESB Application Engineering for Standby and Island Mode applications.
©2009 Cummins Power Generation Inc. All rights reserved. Cummins Power Generation and Cummins are registered trademarks of Cummins
Inc. PowerCommand, AmpSentry and “Our energy working for you.” are trademarks of Cummins Power Generation. Other company, product,
or service names may be trademarks or service marks of others. Specifications are subject to change without notice.
S-1552c (6/09)
Generator set specifications
ISO 8528 Part 1, Class G1 with exceptions - see PTS (Prototype
Governor regulation class
Test Support) Data Sheet
Voltage regulation, no load to full load ± 0.5%
Random voltage variation ± 0.5%
Frequency regulation Isochronous
Random frequency variation ± 0.25%
Radio frequency emissions compliance IEC 801.2 through IEC 801.5; MIL STD 461C, Part 9
Single step load pickup Minimum 25% see PTS data sheet for details
Engine specifications
Design 4 cycle, V-block, turbocharged low temperature aftercooled
Bore 159 mm (6.25 in)
Stroke 190 mm (7.48 in)
3
Displacement 60.3 liters (3685 in )
Cylinder block Cast iron, V16
Battery charging alternator None
Starting voltage 24 volt negative ground
Fuel system Lean burn
Ignition system Individual coil on plug
Air cleaner type Dry replaceable element
Lube oil filter type(s) Full flow and bypass filters
Breather Breather filter
Alternator specifications
Design Brushless, 4 pole, revolving field
Stator 2/3 pitch
Rotor Two bearing
Insulation system Class F or H see ADS (Alternator Data Sheet) for details
Standard temperature rise 105 °C (221 °F) ontinuous @ 40 °C (104 °F) ambient
Exciter type PMG (Permanent Magnet Generator)
Phase rotation A (U), B (V), C (W)
Alternator cooling Direct drive centrifugal blower fan
AC waveform total harmonic distortion < 5% no load to full linear load, < 3% for any single harmonic
Telephone influence factor (TIF) < 50 per NEMA MG1-22.43
Telephone harmonic factor (THF) <3
Available voltages
60 Hz Three phase line–neutral/line-line 50 Hz Three phase line–neutral/line-line
• 220/380 • 230/416 • 240/416 • 255/440 • 220/380 • 230/400 • 240/415 • 254/440
• 277/480 • 347/600 • 1620/13200 • 2400/4160 • 1905/3300 • 3810/6600 • 5774/10000 • 6250/11000
• 7200/12470 • 7970/13800
Note: Some voltages may not be available on all models - consult factory for availability.
Note: Some options may not be available on all models - consult factory for availability.
50 Hz
Data Emissions LT HT
3
Model sheet MN* mg/Nm (°C) (°C)
C995 N5C D-3467 60 500 50 90
This outline drawing is to provide representative configuration
C1200 N5C D-3473 60 500 40 90 details for Model series only.
C1400 N5C D-3347 68 500 40 90
C1400 N5C D-3348 64 250 40 90 See respective model data sheet for specific model outline
C1400 N5C D-3357 66 350 40 90 drawing number.
C1400 N5C D-3358 72 500 40 90
Do not use for installation design
* MN = Methane
Warning: Back feed to a utility system can cause electrocution and/or property damage. Do not connect to any building’s electrical system
except through an approved device or after building main switch is open.