Mag5100W Manual PDF
Mag5100W Manual PDF
SITRANS F
Introduction 1
Safety notes 2
Description 3
SITRANS F
Installing/Mounting 4
Electromagnetic Flowmeters
SITRANS F M MAG 5100 W Connecting 5
Technical data 8
Appendix A
11/2010
A5E03063678-02
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.
CAUTION
without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.
NOTICE
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation for the specific task, in particular its warning notices and
safety instructions. Qualified personnel are those who, based on their training and experience, are capable of
identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be adhered to. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of the
owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
1 Introduction................................................................................................................................................ 5
1.1 Items supplied ................................................................................................................................5
1.2 History ............................................................................................................................................5
1.3 Further Information ........................................................................................................................6
2 Safety notes............................................................................................................................................... 7
2.1 Laws and directives .......................................................................................................................7
2.2 Installation in hazardous area ........................................................................................................9
2.3 Certificates ...................................................................................................................................10
3 Description............................................................................................................................................... 11
3.1 System components ....................................................................................................................11
3.2 Theory of operation......................................................................................................................12
4 Installing/Mounting................................................................................................................................... 15
4.1 Installation safety precautions......................................................................................................15
4.2 Determining a location .................................................................................................................16
4.3 Orienting the sensor.....................................................................................................................18
4.4 Mounting ......................................................................................................................................19
4.5 Potential equalization...................................................................................................................21
5 Connecting .............................................................................................................................................. 23
5.1 Remote installation ......................................................................................................................24
5.2 Installation check .........................................................................................................................26
5.3 Potting ..........................................................................................................................................26
5.4 Direct burial ..................................................................................................................................28
6 Service and maintenance ........................................................................................................................ 29
6.1 Maintenance.................................................................................................................................29
6.2 Recalibration ................................................................................................................................29
6.3 Transportation/storage.................................................................................................................29
6.4 Unit repair.....................................................................................................................................30
6.5 Technical support.........................................................................................................................30
6.6 Return procedures .......................................................................................................................31
7 Troubleshooting/FAQs............................................................................................................................. 33
7.1 Sensor check ...............................................................................................................................33
7.2 Fluctuating process values ..........................................................................................................35
Note
It is the responsibility of the customer that the instructions and directions provided in the
manual are read, understood and followed by the relevant personnel before installing the
device.
1.2 History
The contents of these instructions are regularly reviewed and corrections are included in
subsequent editions. We welcome all suggestions for improvement.
The following table shows the most important changes in the documentation compared to
each previous edition.
Edition Remarks
11/2010 Minor updates
07/2010 First edition
Replaces MAG 5100 W part of SITRANS F M Handbook (A5E02435647) and MAG 5100
W instruction (A5E00718677)
See also
Technical support (Page 30)
Note
Alterations to the product, including opening or improper repairs of the product, are not
permitted.
If this requirement is not observed, the CE mark and the manufacturer's warranty will expire.
General requirements
Installation of the equipment must comply with national regulations.
CAUTION
Material compatibility
Siemens Flow Instruments can provide assistance with the selection of wetted sensor
parts. However, the full responsibility for the selection rests with the customer and Siemens
Flow Instruments can take no responsibility for any failure due to material incompatibility.
CE marked equipment
All meters carry either a CE mark or a CE mark followed by eg.200
● CE200: This indicates that the product conforms to:
– PED 97/23/EC
– LVD 2006/95/EC
– EMC 2004/108/EC
● CE: This indicates that the product conforms to:
– LVD 2006/95/EC
– EMC 2004/108/EC
Table 2- 1 MAG 5100 W (7ME6580 only DN15 ... 600 (½" ... 24"))
WARNING
Equipment used in hazardous areas must be approved for use in hazardous area and
marked accordingly. It is required that the special conditions for safe use provided in the
manual and in the FM / CSA certificates are followed!
WARNING
Make sure the hazardous area approval is suitable for the environment in which the
device will be installed.
WARNING
All approvals are based on non-flammable processes only!
WARNING
Potential equalization
In operation, the output is earthed through the conductive medium being measured and
therefore potential equalisation is necessary throughout the hazardous area.
The apparatus housing shall be connected to the potential equalising conductor in the
hazardous area.
WARNING
Laying of cables
Cables for use in hazardous area must satisfy the requirements for having a proof
voltage < AC 500 V applied between the conductor/ground, conductor/shield and
shield/ground.
Connect the devices that are operated in hazardous areas as per the stipulations
applicable in the country of operation.
2.3 Certificates
Certificates are posted on the Internet and on the documentation CD-ROM shipped with the
device.
See also
Technical data (Page 37)
Certificates on the Internet (http://www.siemens.com/processinstrumentation/certificates)
Communication solutions
The SITRANS F USM II range of add on modules, presently including HART, Foundation
Fieldbus. MODBUS RTU RS 485, PROFIBUS PA / DP and Devicenet, are all applicable with
the SITRANS F M MAG 6000 transmitter.
The SITRANS F M MAG 5100 W sensor housing and flanges are designed in carbon steel
and terminal box in fibre glass reinforced polyamide. Measuring pipe is made of stainless
steel (AISI 304) and liners are available in NBR Hard Rubber, Ebonite Hard Rubber, or
EPDM, which makes the sensor highly resistant to a wide range of chemicals. Electrodes are
made of Hastelloy.
MAG 5100W DN15 ... 40 MAG 5100W DN50 ... 300 MAG 5100W DN350 ... 1200
(7ME6520)
MAG 5100W DN25 ... 2000
(7ME6580)
0DJQHWLF)LHOG
)ORZ
Operating principle
The coil current module generates a pulsating magnetizing current that drives the coils in the
sensor. The current is permanently monitored and corrected. Errors or cable faults are
registered by the self-monitoring circuit.
Input circuit amplifies the flow-proportional induced voltage signal from the electrodes. The
input impedance is extremely high: >1014 Ω which allows flow measurements on fluids with
conductivities as low as 5 µS/cm. Measuring errors due to cable capacitance are eliminated
due to active cable screening.
Digital signal processor converts the analog flow signal to a digital signal and suppresses
electrode noise through a digital filter. Inaccuracies in the transmitter as a result of long-term
drift and temperature drift are monitored and continuously compensated for via the self-
monitoring circuit. The analog to digital conversion takes place in an ultra low noise ASIC
with 23 bit signal resolution. This has eliminated the need for range switching. The dynamic
range of the transmitter is therefore unsurpassed with a turn down ratio of minimum 3000:1.
WARNING
Installation in hazardous location
Special requirements apply to the location and interconnection of sensor and
transmitter. See "Installation in hazardous area" (Page 9)
WARNING
In applications with working pressures/media that can be dangerous to people,
surroundings, equipment or others in case of pipe fracture, we recommend that special
precautions such as special placement, shielding or installation of a security guard or a
security valve are taken when the sensor is mounted.
● Ensure that stresses and loading caused by e.g. earthquakes, traffic, high winds and fire
damage if appropriate are taken into account during installation.
● Ensure that the flowmeter is installed such that it does not act as a focus for pipeline
stresses. External loadings are not taken into account in the flowmeter design.
● Provide adequate protection to minimise any risk of contact with hot surfaces.
WARNING
Prevent personal injuries by assuring that operation below pressure guards cannot take
place, if working with vacuum or fluids boiling readily.
NOTICE
The sensor must always be completely filled with liquid.
● Locate the the flowmeter in u-shaped pipes if pipes are only partially filled or have free
outlet
Example:
A flow of 3 m/s (V) in a sensor with a diameter reduction from DN 100 to DN 80 (d1/d2 = 0.8)
gives a pressure drop of 2.9 mbar.
CAUTION
Abrasive liquids / liquids containing solid particles
A vertical installation minimizes wear and deposits in the sensor
NOTICE
Gas/air bubbles in the liquid
A vertical installation minimizes any negative effect of gas/air bubbles in the liquid
CAUTION
Do NOT mount the sensor with the terminal box sideways
This will position the electrodes at the top where there is possibility for air bubbles and
at the bottom where there is possibility for mud, sludge, sand etc.
NOTICE
Empty pipe detection
For applications with empty pipe detection, the sensor can be tilted 45°, as shown
above.
4.4 Mounting
● Install the sensor in rigid pipelines in order to support the weight of the meter.
● Center the connecting pipelines axially in order to avoid turbulent flow profiles.
● Use proper gaskets according to liner type
Vibrations
Avoid strong vibrations.
CAUTION
In applications with strong vibrations, Siemens recommend remote mounting of the
transmitter!
Torques
Fasten screws according to the torques values below
NOTICE
Torque values are calculated on the basis of use of gaskets.
WARNING
Use in hazardous area!
Cathodic pipe protection is not allowed in hazardous areas
● Isolate the sensor from cathodic protected pipes using insulated bolts.
● Use bypass cable between the mating flanges
NOTICE
Remote mounted sensor versions
If the above is not acceptable, remote mounted sensors can alternatively be connected
as follows:
Connect coil current cable shield at sensor end via a 1.5 µF condensator
Make sure that electrode cable shield is not connected at both ends
Before connecting
● Check that serial numbers on sensor and SENSORPROM® unit are identical.
WARNING
The pertinent regulations must be observed for electrical installation.
Never install the device with the mains voltage switched on!
Danger of electric shock!
The electrodes and magnetic current line may only be connected when the device is not
connected to the power supply.
If the housing is under voltage (power supply), the cover may be unscrewed by qualified
personnel only.
WARNING
Mains supply from building installation Class II
A switch or circuit breaker (max. 15 A) must be installed in close proximity to the equipment
and within easy reach of the operator. It must be marked as the disconnecting device for
the equipment.
Cable specifications
● Only use cables with at least the same degree of protection as the sensor to install the
sensor.
● The line length from the cable gland to the terminals must be kept as short as possible.
Line loops in the terminal box must be avoided.
● To guarantee the IP 67 degree of protection, use cables with the required specifications.
WARNING
Protective conductor terminal
The required cable is min. AGW16 or 1.5 Cu.
WARNING
Wire insulation
The insulation between the connected mains supply and 24 V AC/DC supply for the
flowmeter must at least be rated with double or reinforced insulation at mains voltage.
For field wiring installation: Ensure that the National Installation Code of the country in
which the flowmeters are installed is met.
See also
Cable data (Page 40)
NOTICE
Remote installation only
The following applies to remote installation of MAG 5000 / 6000 or MAG 6000 I.
3. Fit the ½" NPT or M20 cable glands for supply and output cables.
4. Fit and connect electrode and coil cables as shown below.
6KLHOG
CAUTION
Unshielded cable ends
Keep unscreened cable ends as short as possible.
CAUTION
Prevent interference
Separate electrode and coil cables to prevent interference.
WARNING
Mount terminal box lid before power up.
5.3 Potting
If sensor is buried or permanently submerged, terminal box must be encapsulated with
silicon dielectric gel (non-toxic, transparent and self-healing gel)
CAUTION
Do not pot meter before electrical connections have been made.
● Mix the two components of the potting kit well and pour into terminal box.
● Let cure for approximately 24 hours at approximately 25°C (77°F). Curing time increases
by 100% per -10°C (-18°F).
NOTICE
Gel can be penetrated with test instruments or be removed in case of cable replacement.
CAUTION
Sensor should not be subject to heavy vehicles applying excessive weight above sensor
or pipeline
CAUTION
SENSORPROM® memory unit
Remove the SENSORPROM® from terminal box on sensor and relocate in remote
transmitter prior to burying sensor.
All sensor data plate information and serial number should be recorded for each sensor
prior to burying. This will ensure correct matching with SENSORPROM® unit.
WARNING
Electrical cable identification
Use suitable coil and electrode cables
Lay electrical cable identification tape above pea gravel before it is covered with earth.
6.2 Recalibration
Siemens A/S Flow Instruments offers to recalibrate the sensor. The following calibrations are
offered as standard:
● Standard matched pair calibration
Note
For recalibration the memory unit must always be returned with the sensor
6.3 Transportation/storage
Handling
CAUTION
Repair and service must be carried out by Siemens authorized personnel only.
Note
Siemens Flow Instruments defines sensors as non-repairable products.
Additional Support
Please contact your local Siemens representative and offices if you have additional
questions about the device
Find your contact partner at:
Local contact person (http://www.automation.siemens.com/partner)
Required forms
● Delivery Note
● Cover Note for Return Delivery with the following information
Cover note (http://support.automation.siemens.com/WW/view/en/16604370)
– product (ordering number)
– number of devices or spare parts returned
– reason for the return
● Declaration of Decontamination
Declaration of Decontamination
(http://pia.khe.siemens.com/efiles/feldg/files/Service/declaration_of_decontamination_en.
pdf)
With this declaration you certify that the returned products/spare parts have been
carefully cleaned and are free from any residues.
If the device has been operated together with toxic, caustic, flammable or water-
damaging products, clean the device before return by rinsing or neutralizing. Ensure that
all cavities are free from dangerous substances. Then, double-check the device to ensure
the cleaning is completed.
We shall not service a device or spare part unless the declaration of decontamination
confirms proper decontamination of the device or spare part. Shipments without a
declaration of decontamination shall be cleaned professionally at your expense before
further proceeding.
You can find the forms on the Internet and on the CD delivered with the device.
Requirement
To check the SITRANS F M sensors the following test instruments will be required:
● Digital Meter/Multimeter
● Megger
● (Moving Coil Meter)
Sensor check
Remove the transmitter from the sensor or remote position before making the following
checks.
NOTICE
In case of deviation from nominal coil values, the sensor is damaged and must be replaced
WARNING
Potential hazard!
Only carry our a coil insulation check in non-hazardous area!
Sensors with an insulation resistance down to 1 Megohms may still work satisfactorily but
this is not guaranteed.
NOTICE
Sensors removed from line
For sensors removed from line with dry bore, use megger between terminal 82 and
compression plate, and 83 and compression plate to show any water ingress behind
electrodes or within enclosure.
Question
Why do the displayed process values fluctuate when the electrode cable is moved?
Answer
There are several causes to the fluctuating process values:
● Deposits on electrodes
– Clean the electrodes.
● Defect electrode cable
– Replace the cable
● Incorrect cable connection
– Connect the electrode cable (82, 83, 0 and shield) according to the instructions in
chapter Connecting (Page 23)
NOTICE
Vibrating environments
It is recommended to use special low noise cables for sensor sizes DN 2 and 3
installed in vibrating environments.
Table 8- 4 Design
1) : For sizes larger than 600 mm (24") in PN 16, PED conformity is available as cost-added option. The basic unit will
carry the LVD (Low Voltage Directive) and EMC approval.
Description
Cable kit with standard coil cable and electrode cable double
shielded (also available as low noise cable for MAG 1100
sensor )
Standard applications
Compact installation
Liquids with an electrical conductivity ≥ 5 μS/cm.
Remote installation
Standard cable
[µS/cm]
300
200
Conductivity
of medium
100
5
5 100 200 300 [m]
Special cable
[µS/cm]
50
40
Conductivity
30
of medium
20
10
5
50 100 200 300 400 500 [m]
WARNING
For detection of empty sensor the min. conductivity must always be >50 μS/cm and the
max. length of the electrode cable when remote mounted is 50 meters (164 ft). Special
cable must be used!
For remote MID installations the max. cable length is 3 meters (9.8 ft). For other CT
application standard requirements are applicable.
Liner Applications
EPDM Drinking water applications (not hydrocarbons)
Ebonite Drinking water applications wastewater applications and
certain chemicals applications
NBR General purpose. Drinking water, sea waters
Electrodes
Hastelloy C The preferred choice for water and wastewater, chemicals,
food and beverage, and pharmaceutical industries
The tables show the relationship between flow velocity v, flow quantity Q and sensor
dimension DN.
Guidelines for selection of sensor
Min. measuring range: 0 ... 0.25 m/s (0 ... 0.8 ft/s)
Max. measuring range: 0 ... 10 m/s (0 ... ft/s)
Normally the sensor size is selected so that the nominal flow velocity v lies within the
measuring range 1 ... 3 m/s (1 ... 15 ft/s).
$
$
$
$
$
83N58.11
/
/ /
0 0
0
ರ137 ರ137
ರ137
$
$
$
$
$
$
/ /
Dimensions
Nominal size A
Order no. Order no.
7ME6520 NBR or EPDM liner 7ME6580 Ebonite liner
mm inch mm inch mm inch
15 ½ 177 7 - -
25 1 187 7.4 187 7.4
40 1½ 202 8 197 7.8
50 2 188 7.4 205 8.1
65 2½ 194 7.6 212 8.3
80 3 200 7.9 222 8.7
100 4 207 8.1 242 9.5
125 5 217 8.5 255 10.0
150 6 232 9.1 276 10.9
200 8 257 10.1 304 12.0
250 10 284 11.2 332 13.1
300 12 310 12.2 357 14.1
350 14 382 15.0 362 14.3
400 16 407 16.0 387 15.2
450 18 438 17.2 418 16.5
500 20 463 18.2 443 17.4
600 24 514 20.2 494 19.4
700 28 564 22.2 544 21.4
750 30 591 23.3 571 22.5
800 32 616 24.3 606 23.9
900 36 663 26.1 653 25.7
1000 40 714 28.1 704 27.7
1050 42 714 28.1 704 27.7
1100 44 765 30.1 755 29.7
1200 48 820 32.3 810 31.9
1400 54 N/A N/A 925 36.4
1500 60 N/A N/A 972 38.2
1600 66 N/A N/A 1025 40.4
1800 72 N/A N/A 1123 44.2
2000 78 N/A N/A 1223 48.1
Nominal size L
PN 10 PN 16 PN 16 PN 40 Class 150 AS / JIS10K
non-PED AWWA
mm inch mm inch mm inch mm inch mm inch mm inch mm inch
15 ½ N/A N/A N/A N/A N/A N/A 200 7.9 200 7.9 N/A N/A
25 1 N/A N/A N/A N/A N/A N/A 200 7.9 200 7.9 200 7.9
40 1½ N/A N/A N/A N/A N/A N/A 200 7.9 200 7.9 200 7.9
50 2 N/A N/A 200 7.9 N/A N/A N/A N/A 200 7.9 200 7.9
65 2½ N/A N/A 200 7.9 N/A N/A N/A N/A 200 7.9 200 7.9
80 3 N/A N/A 200 7.9 N/A N/A N/A N/A 200 7.9 200 7.9
100 4 N/A N/A 250 9.8 N/A N/A N/A N/A 250 9.8 250 9.8
125 5 N/A N/A 250 9.8 N/A N/A N/A N/A 250 9.8 2501) 9.81)
150 6 N/A N/A 300 11.8 N/A N/A N/A N/A 300 11.8 300 11.8
200 8 350 13.8 350 13.8 N/A N/A N/A N/A 350 13.8 350 13.8
250 10 450 17.7 450 17.7 N/A N/A N/A N/A 450 17.7 450 17.7
300 12 500 19.7 500 19.7 N/A N/A N/A N/A 500 19.7 500 19.7
350 14 550 21.7 550 21.7 N/A N/A N/A N/A 550 21.7 550 21.7
400 16 600 23.6 600 23.6 N/A N/A N/A N/A 600 23.6 N/A 23.6
450 18 600 23.6 600 23.6 N/A N/A N/A N/A 600 23.6 600 23.6
500 20 600 23.6 600 23.6 N/A N/A N/A N/A 600 23.6 600 23.6
600 24 600 23.6 600 23.6 N/A N/A N/A N/A 600 23.6 600 23.6
700 28 700 27.6 700 27.6 N/A N/A N/A N/A 700 27.6 7002) 27.62)
750 30 N/A N/A N/A N/A N/A N/A N/A N/A 750 29.5 7502) N/A
800 32 800 31.5 800 31.5 N/A N/A N/A N/A 800 31.5 8002) 31.52)
900 36 900 35.4 900 35.4 N/A N/A N/A N/A 900 35.4 9002) 35.42)
1000 40 1000 39.4 1000 39.4 N/A N/A N/A N/A 1000 39.4 10002) 39.42)
1050 42 N/A N/A N/A N/A N/A N/A N/A N/A 1000 39.4 N/A N/A
1100 44 N/A N/A N/A N/A N/A N/A N/A N/A 1100 43.3 N/A N/A
1200 48 1200 47.2 1200 47.2 N/A N/A N/A N/A 1200 47.2 12002) 47.22)
1400 54 1400 55.1 N/A N/A 1400 55.1 N/A N/A 1200 47.2 N/A N/A
1500 60 1500 59.1 N/A N/A 1500 59.1 N/A N/A 1200 47.2 N/A N/A
1600 66 1600 63.0 N/A N/A 1600 63.0 N/A N/A 1200 47.2 N/A N/A
1800 72 1800 70.9 N/A N/A 1800 70.9 N/A N/A 1200 47.2 N/A N/A
2000 78 2000 78.7 N/A N/A 2000 78.7 N/A N/A 1200 47.2 N/A N/A
1) Not available with AS flange
2) Not available with JIS 10K flange
Weight
Table 8- 12 Weight
Table A- 2 50 Hz version
Table A- 3 60 Hz version
MAG 1100, MAG 1100F MAG 3100, MAG 3100P, MAG 5100 W
MAG 5100 W
(Order no. 7ME6580) (Order no. 7ME6520)
DN Inch Resistance Tolerance Resistance Tolerance Resistance Tolerance
2 1/12 104 Ω +/− 5 104
3 1/8 104 Ω +/− 5 104
6 1/4 99 Ω +/− 17 104
10 3/8 99 Ω +/− 17 104
151) 1/2 91 Ω +/− 9 104
25 1 91 Ω +/− 17 104 +/− 2 104 +/− 10
40 11/2 91 Ω +/− 9 92 +/− 2 92 +/− 10
50 2 91 Ω +/− 9 92 +/− 2 119.4 +/− 10
65 21/2 99 Ω +/− 17 100 +/− 2 127 +/− 10
80 3 91 Ω +/− 17 94 +/− 2 126 +/− 10
100 4 91 Ω +/− 9 92 +/− 2 125 +/− 10
125 5 92 +/− 2 126 +/− 10
150 6 94 +/− 2 116 +/− 10
200 8 90 +/− 2 109 +/− 10
250 10 92 +/− 2 104 +/− 10
300 12 100 +/− 2 108 +/− 10
350 14 112 +/− 2 100 +/− 6
400 16 100 +/− 4 100 +/− 6
450 18 108 +/− 4 100 +/− 6
500 20 122 +/− 4 100 +/− 6
600 24 115 +/− 4 98 +/− 6
700 28 128 +/− 4 98 +/− 6
750 30 133
800 32 128 +/− 4 98 +/− 6
900 36 131 +/− 4 98 +/− 6
MAG 1100, MAG 1100F MAG 3100, MAG 3100P, MAG 5100 W
MAG 5100 W
(Order no. 7ME6580) (Order no. 7ME6520)
1000 40 131 +/− 4 88 +/− 6
1100 44 126
1200 48 130 +/− 4 88 +/− 6
1400 54 130
1500 60 124
1600 66 133
1800 72 133
2000 78 147
1) On MAG 1100 DN 15 produced as from May 1999 the coil resistance must be 86 ohm, +8/−4 ohm.
NOTICE
Reference values
All resistance values are at 20 °C
The resistance changes proportionally 0.4% / °C
Spare parts
Description
Cable glands, 2 pcs.
M20
½" NPT
Description
Terminal box lid, in polyamide
A.4 Ordering
In order to ensure that the ordering data you are using is not outdated, the latest ordering
data is always available on the Internet: Catalog process instrumentation
(http://www.siemens.com/processinstrumentation/catalogs)
ASIC
Application-Specific Integrated Circuit is an integrated circuit (IC) customized for a particular
use, rather than intended for general-purpose use.
EMC
Electromagnetic compatibility (EMC) is the branch of electrical sciences which studies the
unintentional generation, propagation and reception of electromagnetic energy with
reference to the unwanted effects (Electromagnetic Interference, or EMI) that such energy
may induce. The goal of EMC is the correct operation, in the same electromagnetic
environment, of different equipment which use electromagnetic phenomena, and the
avoidance of any interference effects.
IP
An IP (Ingress Protection) number is used to specify the environmental protection of
enclosures around electronic equipment. These ratings are determined by specific tests. The
IP number is composed of two numbers, the first referring to the protection against solid
objects and the second against liquids. The higher the number, the better the protection. For
example, in IP67 the first Number (6) means that the device is totally protected against dust,
and the second (7) that it is protected against the effect of immersion between 15cm and 1m
PED
The Pressure Equipment Directive (97/23/EC) is the legislative framework on European level
for equipment subject to a pressure hazard. It was adopted by the European Parliament and
the European Council in May 1997 and has been obligatory throughout the European Union
since May 2002.
SENSORPROM
All sensor related settings/data saved on an EPROM. SENSORPROM technology
automatically configures the transmitter at start up providing calibration data, pipe size,
sensor type, and output settings. The SENSORPROM automatically stores values or
settings changed by users, and automatically re-programs any new transmitter without loss
of accuracy.
USM
USM II is a Communication Platform. The Siemens USM II concept enables fitting of add-on
bus modules without loss of functionality:
1. All modules can be fitted as true "plug & play"
2. Module and transmitter are automatically configured through the SENSORPROM
A H
Abrasive liquids, 18 Hazardous area
Add-on modules, (See Communication module) Approvals, 10
Applications, 11 Horizontal pipes
Installation in, 18
Hotline, 30
C
Cable specifications, 24, 40
I
Cathodic protection, 21
Coil insulation check, 33 Inlet / outlet conditions, 16
Coil resistance check, 33 Installation
Communication modules, 11 in U-tube, 16
Compliance, 7 Indoor/outdoor, 15
Contact person, 6 Large pipes, 17
Customer Support Hotline, 30 Location in system, 16
Mounting of sensor, 19
Pipes with free outlet, 16
D Remote, 24
Safety instructions, 15
Decontamination, 31
Internet
Dimensions, 47
Contact person, 6, 31
Direct burial, 28
Flowdocumentation, 6
Document history, 5
Support, 31
Introduction, 5
Items supplied, 5
E
Electrical connection
Cable specifications, 24 L
Remote installations, 24
Laws and directives, 7
Safety instructions, 23
Electrode resistance check, 34
Empty pipe detection, 18
M
Mains supply, 23
F Maintenance, 29
Material compatibility, 7
FAQ
Measurement principle, 12
Fluctuating process values, 34
Mounting, (See Installation)
Flange mating dimensions, 51
P
G
Potential equalization, 21
Gas / Air bubbles, 18
Potting, 27
Pressure
Safety instructions, 15
R
Recalibration, 29
Repair, 30
Return procedures, 31
S
Safety
Instrument safety standards, 7
Safety instructions
Electrical connection, 23
Installation, 15
Safety notes, 7
Sensor check, 33
Sensor orientation, 18
Service, 30, 31
Support, 31
System components, 11
T
Theory of operation, 12
Torques values, 20
Transportation, 29
V
Vertical pipes
Installation in, 18
Vibrations, 19
W
Weight, 49
Wire insulation, 24
Wiring, (See Electrical connection)
Siemens
Siemens Flow
A/S Instruments A/S Subject to change without prior notice
*A5E03063678*
Nordborgvej 81
Flow Instruments Order No.: A5E03063678
DK-6430
DK-6430 Nordborg
Nordborg Literature No.: A5E03063678-02
Denmark Copyright Siemens AG 11.2010
All rights reserved
www.siemens.com/processautomation
www.siemens.com/processautomation