Agip Piping Spec PDF
Agip Piping Spec PDF
ABSTRACT
TABLE OF CONTENTS
1. INTRODUCTION
1.1 PURPOSE
1.2 DEFINITIONS
3. MATERIAL REQUIREMENTS
3.1 GENERAL
3.2 PIPE
3.3 FLANGES
3.4 FITTINGS
3.5 BOLTING AND GASKETS
3.6 VALVES
3.7 SPECTACLE BLINDS AND BLIND & SPACERS
3.8 HIGH PRESSURE AND COPPER-NICKEL PIPING
3.9 NON-METALLIC PIPING
4. WELDING DETAILS
4.1 90° BRANCH REINFORCEMENT
4.2 45° BRANCH REINFORCEMENT
4.3 WELDING DETAILS MINIMUM CLEARANCES
APPENDICES
1. INTRODUCTION
This document covers the minimum requirements for the design and selection of piping components for piping
systems designed for installation on the AGIP KCO Kashagan Field Development Project.
Systems Excluded:-
1.1 PURPOSE
The purpose of this document is to provide a single reference point that specifies the design and selection of
standard piping components for offshore, onshore and pipeline application.
Details of Onshore & Offshore classes are in Attachments 1 to 3 and Pipeline classes are in Attachment 4 to 6
1.2 DEFINITIONS
The COMPANY is the party that initiates the project and ultimately pays for its design and construction. The
Company will generally specify the technical requirements. The Company may also include an agent or
consultant authorised to act for, and on behalf of, the Company.
The CONTRACTOR is the party that carries out all or part of the design, engineering, procurement,
construction, commissioning or management of a project, or operation or maintenance of a facility. The
Company may undertake all or part of the duties of the Contractor.
The Fabricator is the party that carries out all or part of the fabrication, installation and testing of the
pipework.
The SUPPLIER (MANUFACTURER / VENDOR) is the party that manufactures or supplies equipment and
services to perform the duties specified by the Company or Contractor.
2.1.1 In conjunction with this Specification, the Codes, Standards, Regulations and References listed below shall
be applicable. Equivalent alternatives may be offered, however these shall be identified and based on
mutual agreement with Company.
KE01.00.000.KD.P.ST.0009.000 Bulk Materials – Traceability, Marking and Colour Coding for Material
Identification Purposes During Storage and Fabrication
KE01.00.000.KD.P.ST.0012.000 Controlled Stud bolt Tensioning
KE01.00.000.KD.P.ST.0013.000 Technical Supply Requirements Pipe, Fittings and Flanges
KE01.00.000.KD.P.ST.0014.000 Technical Supply Requirements for Valves
KE01.00.000.KD.P.TD.0015.000 Piping Valve Data Sheets
KE01.00.000.KD.P.ST.0016.000 Technical Supply Requirements for Gaskets
KE01.00.000.KD.P.ST.0017.000 Technical Supply Requirements for Bolts
KE01.00.000.AK.A.PR.0045.000 Project Permitting and Regulatory Compliance
KE01.00.000.AK.A.PR.0047.000 Concession Request Procedure
KE01.00.000.KD.A.LD.0002.000 Supplier Documentation Descriptions
KE01.00.000.KD.Q.SP.0001.000 Supplier Quality Requirements
KE01.00.000.KD.Z.PR.0004.000 Supplier Documentation Instructions
KE01.A1.300.KD.P.ST.0001.000 Technical Supply Requirements for Seamless & SAW Carbon
Steel Linepiping for Slug Catcher Material
KE01.B4.000.KD.V.ST.0001.000 High Pressure Pipe Requirements
KE01.B4.000.KD.V.ST.0002.000 High Pressure Piping Welding and Fabrication Specification
Reference to any standard or code shall mean the latest edition of that standard or code including
addenda, supplements or revisions thereto, unless specified otherwise.
ASME B1.1 Unified inch screw Threads, UN and UNR Thread Form
ASME B.1.20.1 Pipe Threads (General Purpose)
ASME B.16.5 Steel Pipe Flanges and Flanged Fittings
ASME B.16.9 Factory Made Wrought Steel Butt-Welding Fittings
ASME B.16.10 Face to Face and End to End Dimensions of Ferrous Valves
ASME B.16.11 Forged Steel Fittings. Socket Welding and Threaded
ASME B.16.20 Metallic Gaskets For Pipe Flanges.
ASME B.16.21 Non-Metallic Flat Gaskets for Pipe Flanges
ASME B.16.25 Butt-Welding Ends for Pipe, Flanges and Fittings
ASME B.16.28 Wrought Steel Butt-Welding Short Radius Elbows and Returns
ASME B.16.34 Steel Valves - Flanged and Butt-Welding Ends
ASME B.16.36 Steel Orifice Flanges. Class 300, 600, 900, 1500 and 2500
ASME B.16.47 Large Diameter Steel Flanges.
ASTM A350 Forgings, Carbon and Low Alloy Steel, requiring Notch Toughness Test for Low
Temperature Components
ASTM A351 Steel Castings, Austenitic, for High Temperature Service
ASTM A352 Steel Castings Ferritic and Martensitic for Pressure Containing Parts Suitable for Low
Temperature Service
ASTM A388 Ultrasonic Examination of Heavy Steel Forgings
ASTM A403 Wrought Austenitic Stainless Steel Piping Fittings
ASTM A420 Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low Temperature Service
ASTM A488/A88M Standard Practice For Steel Castings, Welding, Qualifications Of Procedures And
Personnel
ASTM A515 Carbon Steel Plate for Intermediate and Higher, Temperature Service
ASTM A516 Carbon Steel Plate for Moderate and Lower, Temperature Service
ASTM A671 Standard Specification For Electric-Fusion-Welded Steel Pipe For Atmospheric And
Lower Temperatures
ASTM A694 Carbon Steel High Strength Forgings
ASTM B363 Standard Specification For Seamless And Welded Unalloyed Titanium And Titanium
Alloy Welding Fittings
ASTM B366 Standard Specification For Factory-Made Wrought Nickel And Nickel Alloy Fittings
ASTM B381 Standard Specification For Titanium And Titanium Alloy Forgings
ASTM B423 Standard Specification For Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS
N08825 And N08221) Seamless Pipe And Tube
ASTM B444 Standard Specification For Nickel-Chromium-Molybdenum-Columbian Alloys (UNS
N06625) And Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219)* Pipe And
Tube
ASTM B564 Standard Specification For Nickel Alloy Forgings
ASTM D2310 Machine-Made Reinforced Thermoplastic Resin Pipe
ASTM D2996 Specification for Filament Wound Reinforced Thermosetting Resin Pipe and Fittings
ASTM D4024 Specification for Reinforced Thermosetting Resin Flanges
BS381C Specification For Colours For Identification, Coding And Special Purposes
BS 1414 Steel Gate Valves Flanged and BW Ends
BS1868 Specification For Steel Check Valves (Flanged And Butt-Welding Ends) For The
Petroleum, Petrochemical And Allied Industries
BS 1873 Steel Globe and Globe Stop Check Valves for the Petroleum and Petrochemical
Industries
BS 2080 Face to Face Dimensions for Valves
BS 2600 Methods for Radiographic Examination of Fusion Welds in Steel
BS 2910 Radiographic Examination of Fusion Welded Circumferential Butt Joints in Steel Pipes
BS 3799 Steel Pipe Fittings Screwed and Socket Welding, for the Petroleum Industry
BS 5351 Steel Ball Valves for the Petroleum, Petrochemical and Allied Industries
BS 5352 Steel Wedge Gate, Globe and Check Valves 50mm and smaller
BS 6755 Testing of Valves Part 1 Production Pressure Testing
Part 2 Specification for Fire Testing Requirements
EEMUA 144 90/10 Copper Nickel Alloy Piping for Offshore Applications. Tubes - Seamless and
Welded
1. Seamless Tube, 16 bar and 20 bar rating
2. Seam welded tube, 16 bar and 20 bar rating
EEMUA 145 90/10 Copper Nickel Alloy Piping for Offshore Applications. Flanges – Composite and
Solid
EEMUA 146 90/10 COPPER NICKEL ALLOY PIPING FOR OFFSHORE APPLICATIONS.
FITTINGS
EN 10204 Metallic Products - Types Of Inspection Documents
ISO 1461 Hot dip galvanised coatings on fabricated iron and steel articles. Specifications and
test methods
ISO 3183 Petroleum and Natural Gas Industries – Steel pipes for Pipelines
ISO 13623 Petroleum and Natural Gas Industries - Pipeline transportation systems
ISO 4427 Polyethylene (PE) Pipes for Water Supply
ISO 10423 Petroleum and Natural Gas Industries–Drilling and production equipment–wellhead
and Christmas tree equipment
ISO 10474 Steel And Steel Products - Inspection Documents
ISO 13703 Petroleum And Natural Gas Industries - Design And Installation Of Piping Systems
On Offshore Production Platforms
ISO 14313 Petroleum and Natural Gas Industries – Pipeline Transportation Systems – Pipeline Valves
ISO 15590 Petroleum and Natural Gas Industries – Induction Bends, Fittings and Flanges for
Pipeline Transportation Systems
ISO 15649 Petroleum And Natural Gas Industries - Piping
MSS-SP-25 Standard Marking Systems for Valves and Fittings
MSS-SP-75 Specification for High Test Wrought Butt-Welding Fittings
MSS-SP-95 Swage(d) Nipples and Bull Plugs
MSS-SP-97 Forged Carbon Steel Branch Outlet Fittings - Socket Welding, Threaded and Buttwelding
Ends.
NACE MR0175 Standard Material Requirements - sulphide stress cracking resistant metallic materials
(2003) for oil field equipment
2.1.5 ABBREVIATIONS
3.1 GENERAL
3.1.1 All material piping classes have pipe wall thickness schedules governed by ASME B16.5 pressure limits.
However, in some larger sizes at higher ratings some pressure limits have been determined by pre-selecting
available schedules and wall thickness. This is generally equivalent to “calculate wall” which is normally based
upon line design conditions and is made for economical design.
3.1.3 For steel piping systems the nominal sizes shown in millimetres are equivalent to the following imperial
sizes:
3.1.4 Sizes below ½" and sizes 1¼", 2½", 3½", and 5" shall not be used.
Non-standard pipe sizes shall be avoided and every effort made to eliminate small quantities of large bore pipe
sizes, standardise pipe wall thicknesses and economise on the split between seamless and welded pipe
manufacture.
3.1.8 All inspection documentation shall be fully traceable and cross-referenced by part number, size and purchase
order item number.
3.1.9 Positive Material Identification (PMI) shall be performed on all alloy materials in accordance with specification
KE01.00.000.KD.V.SS.0015.000.
3.1.10 The material specifications contained within this document are the minimum that can be accepted for the
service conditions. Material, equal to or better than those listed will be technically and commercially reviewed.
3.1.11 Piping systems requiring internal chemical cleaning shall have the requirement indicated on P&ID and linelist
and shall be carried out in accordance with KE01.00.000.KD.P.ST.0007.000
3.1.12 Pipes and piping components of welded construction and all materials shall have longitudinal weld joint factor of
1.00, and this factor shall be used on all wall thickness calculations (See 3.2.5). Where lower factors are used,
these shall be on specific cases and shall be noted in the relevant class for the size(s) it covers.
Seamless pipes have a joint factor of 1.00.
3.2 PIPE
3.2.2 Carbon steel pipe (impact tested or otherwise) shall be seamless up to and including 16” NPS. Stainless steel
and Nickel alloy pipe shall be seamless up to and including 6” NPS.
3.2.3 Dimensions of stainless steel pipe and Nickel alloy shall be in accordance with ASME B36.19M.
3.2.4 Welded pipe can be used as an alternative to seamless providing it meets joint factor requirements and is
more cost effective.
3.2.5 Pipe wall thickness calculations are based upon seamless pipe in accordance with the appropriate ASTM or
API material specification.(Except Nickel alloy is based on welded pipe. See 3.2.14 for allowable stresses)
3.2.6 Plain end pipe shall have ends square cut, with burrs removed.
3.2.7 All buttweld and preparations for welding shall be in accordance with ASME B16.25.
3.2.9 Pipe nipples shall be 100mm long, unless noted otherwise for orifice tapping assemblies.
3.2.10 Carbon steel pipe lengths shall be double random. Jointers are not acceptable.
3.2.11 Stainless steel pipe lengths shall be single random. Jointers are not acceptable.
3.2.12 Where carbon steel pipe is specified as galvanised, the galvanising of these items shall be in accordance with
ISO 1461. The minimum galvanising coverage shall not be less than 610 g/m2. Galvanising of fabricated piping
spool shall be in accordance with the non-dip process of ISO 1461.
3.2.14 Alloy materials 625 and 825, UNS 06625 and 08825 respectively shall be supplied in the solution annealed
condition. Alloy 825 seamless and welded and alloy 625 welded are not listed in ASME B31.3. For wall
thickness calculation purposes the allowable stress, tensile and yield values shall be taken from ASME II Part D
Table 1B and are based on welded pipe (worst case material properties). These are as tabulated below.
Selection of seamless or welded pipe shall be governed by manufacturing capabilities and economics.
Wall thicknesses may be revised during detail design to suit actual manufacturing process and material
properties agreed with the manufacturer.
Alloy 825
Alloy 625
3.3 FLANGES
3.3.1 All flanges up to and including 24” NB size shall conform to ASME B16.5. Pipe flanges 26” NB size and
larger shall conform to ASME B16.47 Series A (MSS-SP-44). Series B flanges shall not be used.
3.3.2 Flange facings in all class ratings shall be raised face. Flat face flanges shall only be used where shown in the
piping materials specification classes and where required to mate up with flat faced valves and flanges on
equipment, for example to match bronze valve flanges.
3.3.3 Class 900 lb flanges are identical to Class 1500 lb flanges in sizes up to and including 2½”NB.
3.3.4 Flanges which are designated with an API rating shall be in accordance with API 6A.
3.3.5 Raised face surface finish for steel flanges shall be in accordance with ASME B16.5 paras 6.4.4 and
6.4.4.3. The resultant surface finish, in accordance with ASME B46.1 shall have a 125 to 250 microinch
(3.2 to 6.3µm) roughness on classes 150 & 300 ratings and 63 microinch (1.6 µm) for side wallsidewall
surfaces of RTJ grooves.
3.3.6 Flat face flanges shall be limited to 150 lb classes; surface finish will be as per 150 lb raised face but extend
across full width of flange.
3.3.7 When connecting to flat faced flanges use a raised face flange with the raised face removed and full faced
gaskets with bolt holes punched.
3.3.8 Screwed flanges shall be threaded NPT in accordance with ASME B1.20.1.
3.3.9 Weld neck flanges shall be supplied with a radius at the flange/hub intersection.
3.3.10 Flanges machined from forged bar or billet will not be accepted.
3.3.11 All buttweld end preparations for welding shall be in accordance with ASME B.16.25.
3.3.12 Where carbon steel flanges are specified as galvanised, the galvanising of these items shall be in accordance
with ISO 1461. The minimum galvanising thickness shall not be less than 610 g/m2.
3.3.13 Orifice Flanges (supplied in pairs) to be complete with Jack Screws & Plugs.
3.3.14 1½" NB weldoflanges for thermowells shall be either SCH 160 with a controlled bore of 34.02mm I/D or
SCH.XXS with a controlled bore of 28.02mm.
3.3.15 Ensure that all mating flanges to equipment, vessels, valves, etc., are in line with piping class
requirements. If not, check suitability of supplied connection and provide a compatible component.
3.4 FITTINGS
3.4.1 Where pulled bends are specified in the piping classes they shall be formed by induction bending fully heat
treated and shall have tangent ends. Length of straight pipe tangent ends shall be as stated in the relevant
induction bend data sheets.
3.4.2 Carbon steel fittings (impact tested or otherwise) shall be seamless up to and including 16” NPS. Stainless steel
and Nickel alloy pipe shall be seamless up to and including 6” NPS.
3.4.3 Fittings shall be forged to the final shape and size. Fittings shall not be machined from solid forged billets
without specific approval.
Piping Project Material Specification Sheet 15 of 33
Agip KCO KE01.00.000.KD.P.ST.0001.000
KDPC Rev D03 Jan 2005
3.4.4 Screwed fittings shall be threaded NPT in accordance with ASME B1.20.1. Except when seal welded, screwed
connections to be sealed with PTFE paste with a temperature limit of 200°C for temperatures above 200°C use
graphite and oil.
3.4.6 Swage nipples shall be pipe swaged by forging only. Machining of bar stock, forgings or heavy wall pipe not
permitted. Dimensions shall be in accordance with BS 3799 or MSS-SP-95.
3.4.8 Bar stock material is not acceptable for socket weld or screwed fittings.
3.4.9 All reduction sizes for tees and reducers to be in accordance with ASME B16.9.
3.4.10 Integrally reinforced branch fittings and branch reinforcement pads shall meet the requirements of ASME B31.3
Para.304.3.2.
3.4.11 All branch fittings shall be supported by burst test certification, copies of certificates shall be supplied with bids.
3.4.12 All buttweld end preparations for welding shall be in accordance with ASME B16.25.
3.4.13 Where carbon steel fittings are specified as galvanised, the galvanising of these shall be in accordance with
ISO 1461. The minimum galvanising coverage shall not be less than 610 g/m2.
3.4.14 Threaded caps and plugs to be used at hydrostatic and process vents and drains only.
3.5.1 Bolting
3.5.1.1 Acceptable bolt materials shall be in accordance with ASME 16.5 with the diameter specified as imperial and
the length specified as metric.
3.5.1.2 Stud bolts, jackscrews and capscrews shall be threaded full length. Threads shall be coarse imperial to
ASME B1.1 (UNC threads up to 1” and 8UN 1 1/8” and larger) class 2A with UN heavy hexagonal nuts to
ASME B18.2.2. class 2B. Nuts to be chamfered and faced.
3.5.1.3 Stud bolt lengths shall be the effective thread length excluding the end points, in accordance with ASME
B16.5.
3.5.1.4 All bolting materials shall be supplied with certification to ISO 10474/EN 10204 3.1.B unless specified otherwise
in the purchase order.
3.5.1.5 All bolts and studs shall be packed so as to prevent damage to each other and to the coating (where applicable)
during transportation.
3.5.1.6 Stud bolts shall be supplied complete with nuts as detailed below:
1 1/8” dia and less – 2 nuts
1 ¼” dia and greater – 3 nuts
3.5.1.7 All alloy steel bolting shall be galvanised in accordance with ISO 1461.
In all cases thread fits shall be class 2A for bolts and class 2B for nuts after galvanising/coating.
3.5.1.8 Hydraulic tensioners shall be used for studbolts 1¼" diameter and larger. Each studbolt shall be supplied
complete with three heavy hexagon nuts, length of studbolt shall compensate for the additional nut.
3.5.2 Gaskets
3.5.2.1 Spiral wound gaskets for use with raised face flanges shall be provided with both inner compression ring
and outer guide rings. The inner and outer ring material shall be as specified in the relevant piping class.
3.5.2.2 Oval ring gaskets for ring type joints shall be in accordance with ASME B16.20. Material shall be as specified in
the relevant piping class.
3.5.2.3 When connecting to flat faced flanges use full faced gaskets with bolt holes punched.
3.5.2.4 All gaskets shall be marked in accordance with ASME B16.20. Colour coding for spiral wound gaskets shall be
as per Table 19 of ASME B16.20.
3.6 VALVES
3.6.1.1 Steel-end flanges on valves ½" through 24" NB shall be in accordance with ASME B16.5. Large diameter steel
flanges 26" and larger shall be in accordance with ASME B16.47 Series A (MSS-SP-44).
3.6.1.2 Flange facing finish for steel flanges shall be in accordance with ASME B16.5 paras. 6.4.4 and 6.4.4.1. The
resultant surface finish shall have a 125 to 250 microinch (3.2 to 6.3 µm) roughness on class 150 & 300 ratings,
in accordance with ASME B46.1.
3.6.1.3 Flat face flange surface finish shall extend across full width of flanges.
3.6.1.4 All flanges shall be integrally cast or forged with the valve body, weld-on flanges are not permitted.
3.6.1.5 Control valves with flanged end shall be rated minimum 300 lb up to and including size 8” NB. Larger valves
shall be class rated.
3.6.2 Gear Operations
3.6.2.1 The following chart gives the sizes at which gear operators should be specified:-
Type Class
150 300 600 900 1500/2500
Gate 14” 14” 10” 8” 8”
Globe 8” 8” 6” 6” 4”
Ball 8” 8” 6” 4” 4”
Butterfly/Plug 8” & larger
Note for ball valves sizes indicated are for reduced bore.
3.6.2.2 Gear operators to be fully enclosed type. Maximum hand wheel diameter to be limited to 750mm.
3.6.2.3 Gate and globe valves should be supplied with gear operators in smaller sizes than those shown above where
the operating torque exceeds 350 Nm.
3.6.2.4 Gear operators for gate and globe valves shall be bevel type unless spur type is specifically stated. Both bevel
and spur gear operators shall be the type with 4 or 8 bolt mountings which allows them to be orientated on site
in any of four 90° positions.
3.6.2.5 Ball and butterfly valves shall be lever operated for sizes below those shown above providing the torque to
operate the valve does not exceed 203 Nm using a maximum lever length of 450mm.
3.6.3.1 Soft seated ball valves identified in this specification and specifications KE01.00.000.KD.P.TD.0015.000
and KE01.00.000.KD.P.TD.0014.000 are limited to a design temperature of 200 deg.C Max. If Ball valves
are required above this temperature use metal seated ball valves which shall be considered Piping
Speciality Items (SP) and allocated an SP number. Leak rates for metal seated ball valves shall be equal
to or less than API 598 for gate valves.
3.6.3.2 All ball valves shall be proven firesafe and of anti-static design and type test certified to the requirements of BS
6755 Pt. 2 or API RP 6FA.
3.6.3.3 All ball valves shall be reduced bore, full bore valves shall only be used where noted as ‘FB’ on the relevant
P&ID. Reduced bore ball valves shall be supplied one size down on the required valve nominal bore.
3.6.3.5 When testing split body ball valves, clamping across the flanges to enhance the body seal shall not be
permitted.
3.6.3.6 All non-metallic seals shall be suitable for the extremes of ambient temperature, be explosive decompression
resistant and have proven good service record in all process/utility services envisaged.
3.6.4.1 Bar stock material is not acceptable for socket-weld valve bodies.
3.6.4.2 Unless otherwise specified, stem/gland packing is to be graphite with suitable inhibitor.
All valves shall be suitable for fitting proprietary locking devices or mounting locking brackets to the valve in the
fully open or closed position. Where locking is required it will be indicated on the relevant P&ID.
3.6.4.4 Ball and butterfly valves shall be fitted with positive position indicators. They shall be constructed so that the
indicator (whether it be the handle or some other type of indicator) cannot be misassembled to give an incorrect
indication of whether the valve is open or closed.
3.6.4.5 All gate and globe valve material trim numbers to be in accordance with API 600.
3.6.4.6 Uni-directional valves or valves with a preferred direction of flow, shall have a flow direction arrow cast or
stamped on the body.
3.6.4.7 The minimum design temperatures shown on the valve data sheets do not reflect the minimum temperature
achievable during depressurisation. Minimum survival temperature without operation, and minimum
operating temperature, will be reflected as a note on the relevant valve data sheet and applicable piping
class.
3.6.4.8 All valves shall be supplied with a stainless steel tag stamped with the relevant tag number, securely attached
to each valve with multi-strand non-corrodible wire.
3.6.4.9 All low temperature carbon steel and Cr-Mo valves shall be supplied blast cleaned and primer painted in
accordance with specification KE01.00.000.KD.V.SS.001.000 System 1C. Painting shall be applied after
successful completion of factory testing and inspection. The interior, threaded portions, pipe pup ends, flange
contact faces and various valves identifying markings shall not be painted.
Stainless steel valves shall not be painted.
3.6.5.1 All valves in low temperature service shall be supplied to ensure that gland packing/operator is outside the
pipeline insulation, which may be up to 150mm thick. Standard bonnets may be offered if this criterion can be
met.
3.6.5.2 Where indicated on the valve data sheets as extended bonnet, the Vendor shall supply their standard extended
bonnet for the minimum design temperature. There shall be sufficient vapour space to ensure operation of the
valve is maintained at the minimum design temperature. Full dimensional details of the extended bonnets shall
be supplied with the Vendor’s bid.
3.6.5.3 Use of Butt Weld Ball valves shall be the base case for OFFSHORE where piping classes indicate both flanged
or welded valves. Flanged valves shall be used where strictly necessary to solve layout constraints or operation
and maintenance requirements or where flanged connections are necessary to isolate lines during hydrotesting.
Top entry valves shall be indicated on P&ID’s with the acronym TE.
For OFFSHORE application when flanged valves are necessary, Top Entry valves shall be used where
available in the applicable piping class.
3.6.6 MISCELLANEOUS
Spectacle Blinds, Blinds and Spacers 4" and larger require jackscrews.
High pressure pipe for Offshore Injection and Production flowlines shall be in accordance with specification
KE01.B4.000.KD.V.ST.0001.000 "High Pressure Pipe Requirements", and KE01.B4.000.V.ST.0002.000.
"High Pressure Piping Welding and Fabrication Specification"
All 90/10 Cu/Ni/Fe materials shall be hardness tested and the chemical composition and mechanical properties
shall comply with EEMUA Publications Number 144, 145 and 146. All tubes shall be hydraulically tested.
3.9.1.2 Pipe shall have ends square cut with burrs removed
3.9.1.3 Where HDPE drawn bends are specified they shall be formed by a specified length of pipe pulled to a
defined angle and shall have tangent ends. The tangent end straight pipe length shall be the
manufacturers standard tangent length.
3.10.1 Technical requirements for the design, materials, manufacture, inspection and preparation for shipment of
reinforced thermosetting resin pipes (RTRP) flanges and fittings shall be in accordance with specification
KE01.00.000.KD.V.SS.0017.000
Branch
Pipe Radius
Header Reinforcement
Pipe Pad
5.1 GENERAL
• an alphanumeric character to identify the Piping class Rating according to ASME B16.5 and API
6A, as per following tables 14.1.1 and 14.1.2
• a two-digit progressive number, starting from 01 to 09 inclusive.
Table 5.1.1 Piping Specification sheets Rating class identification to ASME B16.5
A 150#
B 300#
C 600#
D 900#
E 1500#
F 2500#
L 2000#
M 3000#
N 5000#
P 10,000#
R 15,000#
S 20,000#
T Tubing
Example: Item C04 relates to the Piping class no. 04 with Rating ANSI 600#.
ATTACHMENT 1
SOUR/NON-SOUR SERVICES
(BD)- Blow Down
(FL)- LP Flare
(FH)- HP Flare -120 +38 18.9 A312
A04 RF 0
(PM)- LPG Sweet 350270 8.411.3 TP316/316L
* To be used for Early Works Project packaged equipment located in buildings Only
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development P02 F01 F02 D01 D02 D03
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 2 AM Jan-2005
SOUR SERVICES
(AG)- Gas to Atms
(AM)- Amine
(BD)- Blow Down
(CH)- Chemicals
(FH)- HP Flare -45 +38 18.9
A312
A15 (FL)- LP Flare RF 343 8.0 0
TP316/316L
(GY)- Glycol 250 12.0
(VT)- Vessel Trim
SOUR SERVICES
(GA)- Acid Gas
(SG)- Sweep Gas -45 +38 19.6 (Jacketed)
A16 RF 3.0
(SL)- Liquid Sulphur 343 8.6 A333 Gr.6
(VT)- Vessel Trim
(WW)- Waste Water
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development P02 F01 F02 D01 D02 D03
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 3 AM Jan-2005
SOUR SERVICES
(PW)- Produced Water
(LC)- LP Condensate
-45 +38 20.0 ALLOY 825
A28 (RG)- Raw Gas (Sour) RF 0
200 13.8 B423 N08825
(RO)- Raw Oil
(VT)- Vessel Trim
(CH)- Chemicals
-45 +38 20.0
A35 (VT)- Vessel Trim RF Alloy 20 0
100 17.6
(CH)- Chemicals
-45 +38 15.8
A36 (VT)- Vessel Trim RF Titanium 0
50 15.3
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development P02 F01 F02 D01 D02 D03
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 5 AM Jan-2005
SOUR SERVICES
(BD)- Blow Down
(FG)- Fuel Gas
(FH)- HP Flare
(FL)- LP Flare
(GY)- Glycol
(ML)-Methanol
(PG)- Process Gas -46 +38 51.0
B11 RF A333 Gr.6 3.0
(PL)- LPG (Sour) 340 36.1
(PO)- Product Oil
(RG)- Raw Gas (Sour)
(RO)- Raw Oil
(SO)- Slop Oil
(VT)- Vessel Trim
(WF)- Well Fluid
SOUR SERVICES
(AM)- Amine
(BD)- Blow Down
(CH)- Chemicals
(FL)- LP Flare -45 +38 49.6 A312
B15 RF 0
(VT)- Vessel Trim 200 35.7 TP316/316L
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development P02 F01 F02 D01 D02 D03
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 7 AM Jan-2005
SOUR SERVICES
(MC)- MP Condensate
(PL)- LPG (Sour)
-45 +38 51.7 ALLOY 825
B28 (PW)- Produced Watrer RF 0
200 48.6 B423 N08825
(RG)- Raw Gas (Sour)
(VT)- Vessel Trim
SOUR SERVICES
(BD)- Blow Down
(CD)- Closed Drain
(FG)- Fuel Gas
(FH)- HP Flare
(GA)- Acid Gas
(GY)- Glycol
(ML)-Methanol -45 +38 102.0
C11 RTJ A333 Gr.6 3.0
(PL)- LPG (Sour) 340 71.8
(PO)- Product Oil
(RG)- Raw Gas (Sour)
(RO)- Raw Oil
(TG)- Treated Gas
(VT)- Vessel Trim
(WF)- Well Fluid
SOUR SERVICES
(AM)- Amine
(CH)- Chemicals
(TW)- Demin Water (or Deionised) -45 +38 99.2 A312
C15 RTJ 0
(VT)- Vessel Trim 200 71.1 TP316/316L
SOUR SERVICES
(BD)- Blow Down
(CD)- Closed Drain
(RG)- Raw Gas (Sour)
-45 +38 102.0
C17 (RO)- Raw Oil RTJ A333 Gr.6 6.0
340 U9
(TG)- Treated Gas
(VT)- Vessel Trim
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development P02 F01 F02 D01 D02 D03
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 9 AM Jan-2005
SOUR SERVICES
(PW)- Produced Watrer -46 +38 103.4 ALLOY 825
C28 RTJ 0
(VT)- Vessel Trim 150 100.3 B423 N08825
SOUR SERVICES
(PL)- LPG (Sour)
(PW)- Produced Watrer -45 +38 103.4 ALLOY 625
C31 RTJ 0
(RG)- Raw Gas (Sour) 150 100.3 B444 N06625
(VT)- Vessel Trim
SOUR SERVICES
(GA)- Acid Gas A333 Gr.6
-45 +38 102.0
C82 RTJ + 3mm Alloy 625 0
(VT)- Vessel Trim 150 90.6
Cladding
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development P02 F01 F02 D01 D02
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 10 AM Jan-2005
SOUR SERVICES
(BD)- Blow Down
(GA)- Acid Gas
(GY)- Glycol
(ML)-Methanol -45 +38 153.0
D11 RTJ A333 Gr.6 3.0
(PO)- Product Oil 150 135.7
(RG)- Raw Gas (Sour)
(VT)- Vessel Trim
(WF)- Well Fluid
SOUR SERVICES
(AM)- Amine
(CH)- Chemicals
-45 +38 148.9 A312
D15 (TW)- Demin Water (or Deionised) RTJ 0
150 115.6 TP316/316L
(VT)- Vessel Trim
(WW)- Waste Water
SOUR SERVICES
(HC)- High Pressure Condensate
(RG)- Raw Gas (Sour)
(RO)- Raw Oil
(RS)- Sewage (Raw)(Non-sour) -45 +38 153.0
D17 RTJ A333 Gr.6 6.0
(RW)- Raw Water/Technical Water(Non-sour) 200 131.3
(VT)- Vessel Trim
(WF)- Well Fluid
(WW)- Waste Water
SOUR SERVICES
(GY)- Glycol
(HC)- High Pressure Condensate
(MC)- MP Condensate ALLOY 825
-45+38 155.1
D28 (PW)- Produced Watrer RTJ B423 0
200 146.1
(RG)- Raw Gas (Sour) N08825
(VT)- Vessel Trim
(WF)- Well Fluid
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development P02 F01 F02 D01 D02
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 11 AM Jan-2005
SOUR SERVICES
(GA)- Acid Gas A333 Gr.6
(VT)- Vessel Trim -45 +38 153.0 + 3mm
D82 RTJ 0
(WF)- Well Fluid 150 135.7 Alloy 625
Cladding
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development P02 F01 F02 D01 D02 D03
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 12 AM Jan-2005
SOUR SERVICES
(CH)- Chemicals
-45 +38 248.2 A312
E15 (VT)- Vessel Trim RTJ 0
200 178.4 TP316/TP316L
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development P02 F01 F02 D01 D02 D03
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 13 AM Jan-2005
SOUR SERVICES
(CH)- Chemicals
-45 +38 413.6 A312
F15 (VT)- Vessel Trim RTJ 0
200 297.1 TP316/TP316L
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development P02 F01 F02 D01 D02 D03
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 14 AM Jan-2005
SOUR SERVICES
(GA)- Acid Gas
-40 +38 830.0 ALLOY 625
R82 (WF)- Well Fluid 0
121 830.0 B564 N06625
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development P02 F01 F02 D01 D02 D03
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 16 AM Jan-2005
T81 DELETED
Agip KCO KE01.00.000.KD.P.ST.0001.000
KDPC Rev D03 Jan 2005
ATTACHMENT 2
Note:-
The revision numbers for individual line classes is set different from the main document revision numbers.
This is to facilitate issue of revised classes. With this system only revised classes need issuing rather than all the
classes listed.
Revision
Class
0 1 2 3 4 5 6 7 8
A01 Sep-02 28/02/03 26/09/03
A02 Sep-02 28/02/03 26/09/03
A03 Sep-02 28/02/03 26/09/03
A04 - 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
A05 Sep-02 28/02/03 26/09/03 30/06/04
A11 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
A13 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
A15 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
A16 Sep-02 28/02/03 26/09/03 01/01/05
A17 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
A18 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
A20 Jan-05
A21 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
A22 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04
A24 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
A25 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
A28 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
A29 Sep-02 28/02/03 26/09/03
A31 Sep-02 DELETED
A35 - 28/02/03 26/09/03 30/06/04
A36 - 28/02/03 26/09/03 30/06/04
A61 Sep-02 28/02/03 DELETED
A62 Sep-02 28/02/03 26/09/03 30/06/04
A63 - 28/02/03 26/09/03 01/01/05
A65 - 28/02/03 26/09/03 30/06/04 01/01/05
A81 Hold 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
A82 Sep-02 DELETED
B04 - 28/02/03 26/09/03 30/06/04 01/01/05
B11 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
B13 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
B15 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
B17 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
B18 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
B22 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04
B25 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
B28 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
B31 Sep-02 DELETED
B61 Sep-02 28/02/03 DELETED
B65 - 28/02/03 26/09/03 30/06/04 01/01/05
B81 Sep-02 DELETED
B82 - 28/02/03 26/09/03 30/06/04 01/12/04
C04 - 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
C11 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
C13 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
C15 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
C17 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
C18 - 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
C19 Jan-05
C21 Sep-02 28/02/03 26/09/03 30/06/04
C25 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
C28 Sep-02 -- 26/09/03 30/06/04 01/12/04 01/01/05
C31 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
C40 - - 26/09/03 30/06/04 01/01/05
C61 Sep-02 28/02/03 DELETED
C65 - 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
C82 - - 26/09/03 30/06/04 01/12/04 01/01/05
Revision
Class
0 1 2 3 4 5 6 7 8
D04 - 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
D11 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
D13 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
D15 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
D17 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
D28 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
D31 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
D65 - 28/02/03 26/09/03 30/06/04 01/12/04 01/01/05
D81 Sep-02 DELETED
D82 Sep-02 - 26/09/03 30/06/04 01/12/04 01/01/05
E11 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
E15 Sep-02 28/02/03 26/09/03 30/06/04 01/01/05
F11 Sep-02 28/02/03 26/09/03 30/06/04
F15 Sep-02 28/02/03 26/09/03 30/06/04
P81 Sep-02 28/02/03 26/09/03 30/06/04 01/12/04
ATTACHMENT 3
Note:-
For Valve Data Sheets refer to document KE01.00.000.KD.P.TD.0015.000 where standard piping valves are
selected and KE01.C0.000.KD.L.SF.0002.000 (Plug Valves), KE01.C0.000.KD.L.SF.0003.000 (Ball Valves), where
pipeline valves are selected.
(IA)- Instrument Air, (LO)- Lube Oil, (OW)- Oily Water, (RS)- Sewage(Raw), (RW)- Raw Water
ITEM 1.5 mm
(SD)- Sludge (Sewage), (SO)- Slop Oil, (TS)- Treated Sewage, (TW)-Demin Water
(UA)- Utility Air, (UN)- Utility N2,(UW)- Utilty Water, (VT)- Vessel Trim, (WW)- Waste Water
Rating & Facing 150 # RF 125 AARH
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S A105N API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -29 ÷ 38 19,6 ---- ----
S.W. FITTINGS A105N/3000# SPACERS & BLINDS A516 Gr 70 50 19.2 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 17.6 ---- ----
NORMAL (from pipe) A106 Gr.B SMLS -- ---- ---- ---- ----
NIPPLES
SCHEDULE N° - 80 80 80 80 80 STD STD STD STD STD STD STD STD STD STD STD
MATERIAL A106 Gr.B
MANUFACTURE SMLS
WELDING NECK A105N / 150# - RF125 AARH
FLANGES
SLIP ON
LAP JOINT
BLIND A105N / 150# - RF125 AARH
GASKETS 1.5mm CNAF
STUD BOLTS & NUTS A193 Gr B7 / A194 Gr 2H (3)
BUTTERFLY
" Y " STRAINERS
90°-45° ELBOWS A 234 Gr.WPB
1/2 STSW CONC.REDUCTIONS A 234 Gr.WPB
3/4 STSW ECC.REDUCTIONS A 234 Gr.WPB
1 STSW ELLIPT.CAPS A 234 Gr.WPB
RTSW
1½ STSW LJ STUB ENDS
10 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A234 Gr WPB
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14
DN"
NOTE 1
2 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A105N
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A105N
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A105N
NOTES:
1) Use flanged branch fittings for TW only.
2) Use VG8151 & VG8152 in vent, drain & instrument assembly.
3) Bolting shall be zinc coating (hot-dip) to ASTM A-153.
Company's sole property document . Company will protect his right by law.
CLASS : A01
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP
(SEAL WELD AFTER TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
3/4" SOCKET WELD X PBE PIPE NIPPLE 3/4" SOCKET WELD X PBE PIPE NIPPLE
SCREWED GATE VALV SCREWED GATE VALVE
3/4" SCRD SOLID PLUG 3/4" SCRD SOLID PLUG
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
INSTRUMENTS
1/2" SOCKET WELD x
SCREWED GATE VALVE PIPING GASES GASES
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate and carrier by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
3. All exposed threads on pipe nipples are to be covered with weld deposit.
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(IA)- Instrument Air, (OS)- Sludge (Oil), (UW)- Utilty Water, (VT)- Vessel Trim, (WW)- Waste Water
ITEM 0 mm
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S A105N API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 0 ÷ 38 15.0 ---- ----
S.W. FITTINGS --- SPACERS & BLINDS A516 Gr 70 50 15.0 ---- ----
THDD FITTINGS A105N/3000# Galv. TEMP. STRAINERS AISI 316 100 15.0 ---- ----
NORMAL (from pipe) A106 Gr.B SMLS Galv. ---- ---- ---- ----
NIPPLES
SOCKET WELD
PIPE BENDS
MITER ELBOWS
HEADER SIZE
1½
DN"
3/4" SCREWED GATE TBE PIPE NIPPLE 3/4" SCREWED GATE TBE PIPE NIPPLE
VALV VALVE
3/4" SCRD SOLID PLUG 3/4" SCRD SOLID PLUG
INSTRUMENTS INSTRUMENTS
3/4" SCREWED GATE VALVE
3/4" SCREWED GATE VALVE
PIPING PIPING
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S A105N API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -29 ÷ 38 19,6 300 10.2
S.W. FITTINGS A105N/3000# SPACERS & BLINDS A516 Gr 70 50 19.2 340 8.7
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 17.6 ---- ----
NORMAL (from pipe) A106 Gr.B SMLS -- 150 15.8 ---- ----
NIPPLES
SCHEDULE N° - 80 80 80 80 80 STD STD STD STD STD STD STD STD STD STD STD STD STD
MATERIAL A106 Gr.B
MANUFACTURE SMLS
WELDING NECK A 105 N / 150# - RF125 AARH
FLANGES
SLIP ON
LAP JOINT
BLIND A 105 N / 150# - RF125 AARH
GASKETS 4.5 mm SPIRAL WOUND TYPE, graphite/316 CS CENTERING & SS INNER RING
STUD BOLTS & NUTS A193 Gr B7 / A194 Gr 2H(3)
10 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A 234 Gr.WPB
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14
DN"
NOTE
NOTE2 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
16 1 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A105N
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A105N
24 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A105N
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS A105N
NOTES:
1) Use flanged branch fittings for TW only.
2) Use VG8151 & VG8152 in vent, drain & instrument assembly.
3) Bolting shall be zinc coating (hot-dip) to ASTM A-153.
Company's sole property document . Company will protect his right by law.
CLASS : A03
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP
(SEAL WELD AFTER TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
3/4" SOCKET WELD X PBE PIPE NIPPLE 3/4" SOCKET WELD X PBE PIPE NIPPLE
SCREWED GATE VALV SCREWED GATE VALVE
3/4" SCRD SOLID PLUG 3/4" SCRD SOLID PLUG
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate and carrier by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
3. All exposed threads on pipe nipples are to be covered with weld deposit.
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A182 F316/L -120 ÷ 38 18.9 ---- ----
S.W. FITTINGS SPACERS & BLINDS A182 F316/L 50 18.3 ---- ----
THDD FITTINGS -- TEMP. STRAINERS AISI 316 100 16.0 ---- ----
NORMAL (from pipe) A312 TP 316/L -- 150 14.7 ---- ----
NIPPLES
SCHEDULE N° - 40S 40S 40S 40S 40S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10 10 10
MATERIAL A312 Gr. TP316/316L A358 Gr. TP316/316L
MANUFACTURE SMLS EFW
WELDING NECK A182 F316/F16L / 150# RF 125AARH
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A182 F316/F316L / 150# RF 125AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A193 Gr B8M Class 2 / A194 Gr 8M
BALL VBA1021,VBA1521(5) VBA1038,VBA1538(5)
FB VBA1121(4),VBA1621(5) VBA1138(4),VBA1638(5)
VALVES
14 NOTE 1 RTEE RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
16
DN"
RTEE RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
24 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A182 F316/L
30 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A182 F316/L
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RF WN FLG 20-48 3
FLG BALL VALVE RF BLIND FLANGE
RF BLIND FLG >48 4
VDB3021(<200C)
3/4" RFMODULAR DOUBLE 3/4" RFMODULAR DOUBLE
VDB3521(>200C) BLOCK & BLEED VALVE
BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(DW)- Potable Water, (FF)- Fire Foam, (IA)- Instrument Air, (TW)-Demin Water
ITEM 0 mm
(UW)- Utilty Water, (VT)- Vessel Trim, (WW)- Waste Water
Rating & Facing 150 # RF 125 AARH
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A182 F316/L -45 ÷ 38 18.9 ---- ----
S.W. FITTINGS SPACERS & BLINDS A182 F316/L 50 18.3 ---- ----
THDD FITTINGS A182 F316/L -- TEMP. STRAINERS AISI 316 100 16.0 ---- ----
NORMAL (from pipe) A312 TP 316/L -- 125 15.4 ---- ----
NIPPLES
SCHEDULE N° - 40S 40S 40S 40S 40S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10
MATERIAL A312 Gr. TP316/316L A358 Gr. TP316/316L
MANUFACTURE SMLS EFW
WELDING NECK A182 F316/F316L / 150# RF 125AARH
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A182 F316/F316L / 150# RF 125AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (4)
GATE VG8055,VG8056,VG8057 VG1065
Note 3
VALVES
14
DN"
NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A182 F316/L
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A182 F316/L
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS A182 F316/L
36 SLET SOCKOLETS
Company's sole property document . Company will protect his right by law.
CLASS : A05
HYDROSTATIC TEST VENTS & DRAINS
3/4" SCRD CAP
BUTT WELD TEE EQUAL OR (SEAL WELD AFTER TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -46 ÷ 38 19,6 ---- ----
S.W. FITTINGS SPACERS & BLINDS A516 Gr 70 50 19.2 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 17.6 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 15.8 ---- ----
NIPPLES
SCHEDULE N° XXS 160 160 160 80 STD STD STD STD STD STD STD STD STD STD STD STD XS XS XS XS
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 150# - RF125 AARH
FLANGES
SOCKET WELD
THREADED
SLIP ON
ORIFICE
BLIND A 350 LF2 / 150# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (4)
BALL VBA1010,VBA1510(7) VBA1030,VBA1530(7)
FB VBA1110(6),VBA1610(6,7) VBA1130(6),VBA1630(6,7)
VALVES
NLEB
16 NOTE
NOTE11 RTEE RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
18 NOTE 1 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A350 LF2
26 RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
28 WLET RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE SLET SOCKOLETS
36 RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE NLET NIPOLETS THDD
46 RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE PTOP PIPE TO PIPE
1/2 3/4 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 36 46
DN" BRANCH SIZE
NOTES: 4) Bolting shall be zinc coating (hot-dip) to ISO 1461.
1) Use flanged branch fittings for TW, PI & flanged valve only. 5) All materials shall meet the requirements of spec KE01.00.000.KD.V.SS.0007.000
2) DELETED 6) To be used only when indicated on P&ID's
3) Ball valves may be used to 200°C only and as restricted by the press/temp. 7) High temp valves >=200C
limitations of the soft materials within the construction of the valves 8) Only selected fittings are used for 46" size
9) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development 5
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 2 AM Jan-2005
SERVICE : (AG )- Gas to Atms, (BD)- Blow Down, (CD)- Closed Drain, (GA)- Acid Gas,
A11
CORR.ALLOWANCE
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -46 ÷ 38 14,2 ---- ----
S.W. FITTINGS SPACERS & BLINDS A516 Gr 70 100 13.8 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 200 13.0 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 300 10.0 ---- ----
NIPPLES
SOCKET WELD
THREADED
SLIP ON
ORIFICE
BLIND A 350 LF2 / 150# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (4)
BALL
FB
VALVES
GLOBE
CHECK
PIPE BENDS
MITER ELBOWS
HEADER SIZE
NLEB
NOTE
NOTE11 RTSC REDUCTION THDD TEE
1/2 3/4 1 1½ 2 12 30 36 42 48 56 60
DN" BRANCH SIZE
NOTES:
SEE SHEET 1 FOR NOTES
Company's sole property document . Company will protect his right by law.
CLASS : A11
HYDROSTATIC TEST VENTS & DRAINS
3/4" RF BLIND FLANGE 3/4" RF BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING 3/4" RF WN FLANGE 3/4" RF WELDOFLANGE
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RF WN FLG 20-48 3
FLG BALL VALVE RF BLIND FLANGE
RF BLIND FLG >48 4
VDB3010(<200C)
3/4" RFMODULAR DOUBLE 3/4" RFMODULAR DOUBLE
BLOCK & BLEED VALVE VDB3510(>200C)
BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S -- API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 19,6 ---- ----
S.W. FITTINGS LF2/3000# SPACERS & BLINDS A516 Gr 70 50 19.2 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 17.6 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 15.8 ---- ----
NIPPLES
SCHEDULE N° - 80 80 80 80 80 STD STD STD STD STD STD STD STD STD STD STD STD STD STD
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 150# - RF125 AARH
FLANGES
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 150# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL VBA1010,VBA1510(6) VBA1030,VBA1530(6)
FB VBA1110(6),VBA1610(5,6) VBA1130(6),VBA1630(5,6)
VALVES
10 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14 2
NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
DN"
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A350 LF2
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
24 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS A350 LF2
36 RTEE RTEE RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS A350 LF2
NOTES: 3) DELETED
1) Use flanged branch fittings for TW, PI & flanged valve only. 4) Bolting shall be zinc coating (hot-dip) to ISO 1461.
Use TLET for hydrotest vents & drains only. 5) To be used only when indicated on P&ID's
2) Ball valves may be used to 200°C only and as restricted by the 6) High temp valves >=200C
press/temp.limitations of the soft materials within the construction of the valves
7) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
CLASS : A13
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP (SEAL WELD AFTER
TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
SOCKOLET+PBE NIP
+SW FLG (1.5")
RF SW FLANGE + PBE NIP
SOCKET WELD TEE WELDOFLANGE (2")
EQUAL OR REDUCING
HEADER SIZE 3/4" to 1 1/2" HEADER SIZE 2" >= WELDOLET+FLG (3")
(VENT 1.5" - 3")
VDB3010(<200C)
3/4" RF MODULAR DOUBLE BLOCK 3/4" RF MODULAR DOUBLE
VDB3510(>200C) BLOCK & BLEED VALVE
& BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
SOCKET
WELD TEE EQUAL OR 3/4" RF WN FLANGE
REDUCING
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A182 F316/L -45 ÷ 38 18.9 ---- ----
S.W. FITTINGS SPACERS & BLINDS A182 F316/L 50 18.3 ---- ----
THDD FITTINGS -- TEMP. STRAINERS AISI 316 100 16.0 ---- ----
NORMAL (from pipe) A312 TP 316/L -- 150 14.7 ---- ----
NIPPLES
SCHEDULE N° - 40S 40S 40S 40S 40S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10 STD STD
MATERIAL A312 Gr. TP316/316L A358 Gr. TP316/316L
MANUFACTURE SMLS EFW
WELDING NECK A182 F316/F16L / 150# RF 125AARH
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A182 F316/F316L / 150# RF 125AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(6)
BALL VBA1015,VBA1515(7) VBA1035,VBA1535(7)
FB VBA1115(5),VBA1615(5,7) VBA1135(5),VBA1635(5,7)
VALVES
16 NOTE 1 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A182 F316/L
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A182 F316/L
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS
NOTES: 4) Ball valves may be used to 200°C only and as restricted by the press/temp.
1) Use flanged branch fittings for TW, PI & flanged valve only. limitations of the soft materials within the construction of the valves
2) All 316 material must be dual certified 316/316L 5) To be used only when indicated on P&ID's
3) DELETED 6) Bolting shall be zinc coating (hot-dip) to ISO 1461.
7) High temp valves >=200C
8) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development 4
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 2 AM Jan-2005
SERVICE : (AG )- Gas to Atms, (AM)- Amine, (BD)- Blow Down, (CH)- Chemicals,
A15
CORR.ALLOWANCE
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A182 F316/L -45 ÷ 38 18.9 ---- ----
S.W. FITTINGS SPACERS & BLINDS A182 F316/L 100 16.0 ---- ----
THDD FITTINGS -- TEMP. STRAINERS AISI 316 200 13.4 ---- ----
NORMAL (from pipe) A312 TP 316/L -- 300 9.7 ---- ----
NIPPLES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A182 F316/F316L / 150# RF 125AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(6)
BALL
FB
VALVES
GLOBE
CHECK
TLET THREDOLETS
72 STEE
SLET SOCKOLETS
NOTES:
SEE SHEET 1 FOR NOTES
Company's sole property document . Company will protect his right by law.
CLASS : A15
HYDROSTATIC TEST VENTS & DRAINS
3/4" RF BLIND FLANGE 3/4" RF BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING 3/4" RF WN FLANGE 3/4" RF WELDOFLANGE
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RF WN FLG 20-48 3
FLG BALL VALVE RF BLIND FLANGE
RF BLIND FLG >48 4
VDB3015(<200C)
3/4" RF MODULAR DOUBLE 3/4" RF MODULAR DOUBLE
VDB3515(>200C) BLOCK & BLEED VALVE
BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
JACKETED FABRICATION KE01.00.000..KD.P.ST.0003.000 RED. S.O. FLG.S A350LF2 DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS --- -45 ÷ 38 19,6 ---- ----
S.W. FITTINGS LF2/6000# SPACERS & BLINDS --- 50 19.2 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS --- 100 17.6 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 15.8 ---- ----
NIPPLES
SCHEDULE N° - - 160 160 160 80 STD STD STD STD STD STD
MATERIAL A333 Gr.6 SMLS
MANUFACTURE SMLS
WELDING NECK
FLANGES
THREADED
PIPE BENDS
MITER ELBOWS
HEADER SIZE
2
DN"
8 WLET WELDOLETS
NOTES 1)All jacketed piping shall be fabricated in accordance 5) Reducing Slip-on flange to have full size hub with flange o/d as follows:
with Specification KE01.00-000.KD.P.DS.0003.000. 2"X1"X6"(152mm o/d), 3"X2"X7.5"(190mm o/d), 4"X3"X9" (229mm o/d),
2) No copper or copper bearing alloys permited. 6"X4"X11" (279mm o/d), 8"X6"X13.5"(343mm o/d), 10"X8"X16"(406mm o/
3) Stress analysis required for all jacketed piping. 6) Bolting shall be zinc coating (hot-dip) to ISO 1461.
4) SW fittings are for jacket side steam and condensate lines only. 5) All materials shall meet the requirements of spec KE01.00.000.KD.V.SS.0007.00
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development 0 1 2 3 4 5
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 1 AM Jan-2005
SERVICE : (BD)- Blow Down, (CH)- Chemicals, (CD)- Closed Drain,
A17
CORR.ALLOWANCE
(FH)- HP Flare, (GA)- Acid Gas, (LP)- LP Condensate, (RG)- Raw Gas,
ITEM 6 mm
(RO)- Raw Oil, (SO)- Slop Oil, (TG)- Treated Gas, (VT)- Vessel Trim, Rating & Facing
(OW) - Oily Water, (WW) - Waste Water SOUR SERVICE
150 # RF 125 AARH
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -46 ÷ 38 19,6 ---- ----
S.W. FITTINGS SPACERS & BLINDS A516 Gr 70 50 19.2 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 17.6 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 15.8 ---- ----
NIPPLES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 150# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (7)
BALL VBA1022,VBA1522(9) VBA1050,VBA1550(9)
FB VBA1122(8),VBA1622(9) VBA1150(8),VBA1650(9)
VALVES
16 NOTE 1 RTEE RTEE RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
18
DN"
RTEE RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE
WLET
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
28 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A350 LF2
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
36 RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE SLET SOCKOLETS
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
WELDOFLANGE
(1.5"-2")
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING
WELDOLET+FLG (3")
HEADER SIZE 1" to 1 1/2" HEADER SIZE 2" >=
(VENT 1.5" - 3")
VDB3022(<200C)
1" RF MODULAR DOUBLE 1" RF MODULAR DOUBLE
VDB3522(>200C)
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
1" 300 RF
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 1" 300 RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use 1/2" sch 160 pipe & flange in Alloy 825 (See Notes 3 sheet 2)
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 19,6 ---- ----
S.W. FITTINGS SPACERS & BLINDS A516 Gr 70 50 19.2 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 17.6 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 15.8 ---- ----
NIPPLES
SCHEDULE N° - XXS 160 160 160 80 STD STD STD STD STD STD STD STD STD STD STD
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 150# - RF125 AARH
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 150# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (5)
BALL VBA1010 VBA1030
Note 8 FB VBA1110(7) VBA1130(7)
VALVES
DIAPHRAGM VDP1010(8)
IN-LINE DBB VDB3110 (10)
90°-45° ELBOWS A 420 Gr.WPL6 (9)
1/2 STEE CONC.REDUCTIONS A 420 Gr.WPL6 (9)
3/4 STEE ECC.REDUCTIONS A 420 Gr.WPL6 (9)
1 STEE ELLIPT.CAPS A 420 Gr.WPL6 (9)
RTEE
1½ STEE LJ STUB ENDS
10 RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE (9) A420 WPL6
14
DN"
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
TLET THREDOLETS
SLET SOCKOLETS
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RF WN FLG 20-48 3
FLG BALL VALVE RF BLIND FLANGE
RF BLIND FLG >48 4
VDB3010(<200C)
3/4" RF MODULAR DOUBLE
3/4" RF MODULAR DOUBLE BLOCK
BLOCK & BLEED VALVE
& BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RF MODULAR DOUBLE BLOCK
& BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" 300 RF WN
FLANGE (TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S A350LF2 API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 19,6 ---- ----
S.W. FITTINGS A350LF2/3000# SPACERS & BLINDS A516 Gr 70 50 19.2 ---- ----
THDD FITTINGS TEMP. STRAINERS AISI 316 100 17.6 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- ---- ----
NIPPLES
SCHEDULE - XXS 160 160 160 80 STD STD STD STD STD STD STD STD STD STD STD
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 150# - RF125 AARH
FLANGES
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 150# - RF125 AARH
GASKETS 1.5mm CNAF
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (Note 3)
GATE VG8050,VG8051,VG8052 VG1060 (Note 4)
(Note 2)
VALVES
10 T'LET
TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
S'LET
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14
DN"
NOTE 12 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A350 LF2
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
NOTES: 4) Where Gate Valves with extended stems are required, use
1) Use flanged branch fittings for TW only. VG1060EX3000
2) Use VG8051 & VG8052 in vent, drain & instrument assembly.
3) Bolting shall be zinc coating (hot-dip) to ISO 1461.
Company's sole property document . Company will protect his right by law.
CLASS : A20
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP
(SEAL WELD AFTER TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(FW)- Fire water, (HM)- Heating Medium,(IA)- Instrument Air, (LO)- Lube Oil, (OW)- Oily Water,
ITEM 1.5 mm
(PA)- Plant Air,(RS)- Sewage(Raw), (RW)- Raw Water/Technical Water(SD)- Sludge (Sewage),
Rating & Facing
(SO)- Slop Oil, (TS)- Treated Sewage, (TW)-Demin Water, (UA)- Utility Air, (UN)- Utility N2, 150 # RF 125 AARH
(UW)- Utilty Water, (VT)- Vessel Trim, (WW)- Waste Water
REFERENCE SPECIFICATIONS KE01.00.000.KD.V.SS.0018.000 COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.P.ST.0002.000 RED. THDD FLG.S A350LF2 API 6D
PIPING CLASS KE01.00.000.KD.V.SS.0018.000 RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.P.ST.0002.000 DRIP RINGS T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 19,6 ---- ----
S.W. FITTINGS A350LF2/3000# SPACERS & BLINDS A516 Gr 70 50 19.2 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 17.6 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 120 16.8 ---- ----
NIPPLES
SCHEDULE - 80 80 80 80 80 STD STD STD STD STD STD STD STD STD STD STD STD STD
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 150# - RF125 AARH
FLANGES
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 150# - RF125 AARH
GASKETS 1.5mm CNAF
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(5)
GATE VG8050,VG8051,VG8052 VG1060 (Note 3)
(Note 2)
VALVES
10 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14
DN"
NOTE 1
2 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A350 LF2
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS A350 LF2
36 RTEE RTEE RTEE RTEE RTEE RTEE SLET SOCKOLETS A350 LF2
NOTES: 4) Use ball valves 4"<= in air/N2 Fuel gas lines and as indicated on P&ID only
1) Use flanged branch fittings for TW only. 5) Bolting shall be zinc coating (hot-dip) to ISO 1461.
2) Use VG8051 & VG8052 in vent, drain & instrument assembly.
3) For FW:- use butterfly valves for ring mains only.All pumps,tanks, shut-off and
isolation valves use gate valves. V**EX**** valves are with extended stem and floor column.
Company's sole property document . Company will protect his right by law.
CLASS : A21
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP
(SEAL WELD AFTER TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. Or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(FW)- Fire Water, (IA)- Instrument Air, (OS)- Sludge (Oil), (OW)- Oily Water, (SO)- Slop Oil
ITEM 0 mm
(UW)- Utilty Water, (UN)- Utility N2, (VT)- Vessel Trim, (WW)- Waste Water
(UA)- Utility Air
Rating & Facing 150 # RF 125 AARH
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S A350LF2 API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 16.0 ---- ----
S.W. FITTINGS --- SPACERS & BLINDS A516 Gr 70 50 16.0 ---- ----
THDD FITTINGS A350LF2/3000# Galv. TEMP. STRAINERS AISI 316 100 16.0 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS Galv. ---- ---- ---- ----
NIPPLES
SOCKET WELD
BALL(Note 3) VBA1040
" Y " STRAINERS
90°-45° ELBOWS A 420 Gr.WPL6
CONC.REDUCTIONS A 420 Gr.WPL6
ECC.REDUCTIONS A 420 Gr.WPL6
ELLIPT.CAPS A 420 Gr.WPL6
LJ STUB ENDS
PIPE BENDS
MITER ELBOWS
HEADER SIZE
1½
DN"
RTSC RTSC RTSC STSC RTSC REDUCTION THDD TEE A350 LF2
NOTES: 3) Use ball valves 2"<= in air/N2 lines and as indicated on P&ID only
1) Flanges <= 4"NB to be used as required only. 4) Bolting shall be zinc coating (hot-dip) to ISO 1461.
2) 6" & larger piping shall be fabricated as flanged spools & 5) Use FF flanges/gaskets when matching FF valves/equipment.
galvanised per ASTM A153. No spool shall exceed 2m X 2m X 10m
4" & smaller fabricated from galvanised T & C pipes & fittings
Company's sole property document . Company will protect his right by law.
CLASS : A22
HYDROSTATIC TEST VENTS & DRAINS
SCREWED TEE EQUAL OR 3/4" SCRD CAP
(SEAL WELD AFTER TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TBE PIPE
NIPPLE 100mm
INSTRUMENTS INSTRUMENTS
3/4" SCREWED GATE VALVE
PIPING PIPING
3/4" SCREWED GATE VALVE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S A350LF2 API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 15.0 ---- ----
S.W. FITTINGS --- SPACERS & BLINDS A516 Gr 70 65 15.0 ---- ----
THDD FITTINGS A350LF2/3000# Galv. TEMP. STRAINERS AISI 316 ---- ---- ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS Galv. ---- ---- ---- ----
NIPPLES
SOCKET WELD
PIPE BENDS
MITER ELBOWS
HEADER SIZE
1½
DN"
RTSC RTSC RTSC STSC RTSC REDUCTION THDD TEE A350 LF2
INSTRUMENTS INSTRUMENTS
3/4" SCREWED GATE VALVE
PIPING PIPING
3/4" SCREWED GATE VALVE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S A350LF2 API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 19,6 300 10.2
S.W. FITTINGS A350LF2/3000# SPACERS & BLINDS A516 Gr 70 50 19.2 340 8.7
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 17.6 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 15.8 ---- ----
NIPPLES
SCHEDULE N° - 80 80 80 80 80 STD STD STD STD STD STD STD STD STD STD STD STD STD STD
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 150# - RF125 AARH
FLANGES
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 150# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(3)
GATE VG8050,VG8051,VG8052 VG1070
(Note 2)
VALVES
10 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14 NOTE 1
2 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
DN"
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A350 LF2
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
24 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS A350 LF2
36 RTEE RTEE RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS A350 LF2
NOTES: 4) For 42" & 48", only selected fittings have been add to commodity catalogue
1) Use flanged branch fittings for TW only.Use TLET for hydro test vents only.
2) Use VG8051,VG8052 in vent, drain & instrument assembly.
3) Bolting shall be zinc coating (hot-dip) to ISO 1461.
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development 3 4
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 2 AM Jan-2005
SERVICE : (AG )- Gas to Atms, (BD)- Blowdown, (BW)- Boiler Feed Water, (LC)- LP Condensate,
A25
CORR.ALLOWANCE
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S A350LF2 API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 10.0
S.W. FITTINGS A350LF2/3000# SPACERS & BLINDS A516 Gr 70 185 6
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- ---- ----
NIPPLES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 150# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(3)
GATE
VALVES
GLOBE
CHECK
PIPE BENDS
MITER ELBOWS
HEADER SIZE
SWLT SWEEPOLETS
TLET
SLET WLET WLET WELDOLETS A350 LF2
42 RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS A350 LF2
NOTE 1
48 RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS A350 LF2
NOTES:
See Sheet 1 for Notes
Company's sole property document . Company will protect his right by law.
CLASS : A25
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP
(SEAL WELD AFTER TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS B564N08825 -45 ÷ 38 20.0 ---- ----
S.W. FITTINGS --- SPACERS & BLINDS B564N08825 50 19.5 ---- ----
THDD FITTINGS --- -- TEMP. STRAINERS --- 100 17.6 ---- ----
NORMAL (from pipe) B423 N08825 -- 150 15.8 ---- ----
NIPPLES
SCHEDULE N° - 40S 40S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S 10S
MATERIAL B423 N08825 (Alloy 825)
MANUFACTURE SMLS/WELDDED
WELDING NECK B564 N08825 / 150# RF 125AARH
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND B564 N08825 / 150# RF 125AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/Inc 825 316 CENTERING & Inc 825 INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (4)
BALL VBA1017 VBA1037
FB VBA1117(6) VBA1137(6)
VALVES
14 NOTE 1
DN"
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS B564N08825
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS
36 SLET SOCKOLETS
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RF WN FLG 20-48 3
FLG BALL VALVE RF BLIND FLANGE
RF BLIND FLG >48 4
VDB3017(<200C)
3/4" RF MODULAR DOUBLE 3/4" RF MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RFMODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" 300 RF WN
FLANGE (TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(PW)- Produced Water, (OW)- Oily Water, (SO)- Slop Oil, (TS)- Treated Sewage,
ITEM 0 mm
(TW)- Demin Water, (UW)- Utility Water, (VT)- Vessel Trim, (WW)- Waste Water,
Rating & Facing 150 # FF 125 AARH
SCHEDULE N° -
MATERIAL D2996, D2310 11FX MECHANICAL LOCK M x F (5)
MANUFACTURE RTRP Epoxy Resin Reinforced liner
WELDING NECK D2996, D2310 RTRP 11FX/ MECHANICAL LOCK F x 150# FF (5)
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND D2996, D2310 RTRP 11FX/ 150# FF
GASKETS 1.5 mm Nitrile Rubber
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(3)
GATE VG8051(1) VG1060,VG1060EX3000 (2)
VALVES
GLOBE
CHECK VC1030
PIPE BENDS
MITER ELBOWS
6 SWLT SWLT RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE(4,5) RTRP 11FX
8 SWLT SWLT RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
10
DN"
SWLT SWLT RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
12 SWLT SWLT RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE
14 SWLT SWLT RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
16 SWLT SWLT RTEE RTEE RTEE RTEE RTEE STEE SWLT SADDLE BRANCH(4,5) RTRP 11FX
20 SWLT SWLT MANF STD RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS
24 SWLT SWLT RTEE RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS B462N08020 -45 ÷ 38 20.0 ---- ----
S.W. FITTINGS --- SPACERS & BLINDS B462N08020 50 19.5 ---- ----
THDD FITTINGS --- -- TEMP. STRAINERS --- 100 17.6 ---- ----
NORMAL (from pipe) B464 N08020 -- ---- ---- ---- ----
NIPPLES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND B462 N08020 / 150# RF 125AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/Alloy 20 316 CENTERING & Alloy 20 INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL VBA1018
VALVES
GLOBE VGL8058
CHECK VC8058
PIPE BENDS
METER ELBOWS
1/2 STEE
HEADER SIZE
3
DN"
8 SWLT SWEEPOLETS
14 SLET SOCKOLETS
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-10 1.5
FLGD BALL VALVE
FLGD BALL VALVE
WELDOFLANGE
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING
RF WN FLG
FLG BALL VALVE RF BLIND FLANGE
RF BLIND FLG
VDB3018
3/4" RF MODULAR DOUBLE BLOCK 3/4" RF MODULAR DOUBLE
& BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RF MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" 300 RF WN
FLANGE (TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS B363 WPT2 -45 ÷ 38 15.8 ---- ----
S.W. FITTINGS --- SPACERS & BLINDS B363 WPT2 50 15.3 ---- ----
THDD FITTINGS --- -- TEMP. STRAINERS --- ---- ---- ---- ----
NORMAL (from pipe) B337 Gr 2 -- ---- ---- ---- ----
NIPPLES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND B381 F2 / 150# RF 125AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/Ti 316 CENTERING & Ti INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (4)
BALL VBA1019
VALVES
GLOBE VGL8059
CHECK VC8059
PIPE BENDS
METER ELBOWS
1/2 STEE
HEADER SIZE
3
DN"
8 SWLT SWEEPOLETS
14 SLET SOCKOLETS
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-10 1.5
FLGD BALL VALVE
FLGD BALL VALVE
WELDOFLANGE
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING
RF WN FLG
FLG BALL VALVE RF BLIND FLANGE
RF BLIND FLG
VDB3019
3/4" RF MODULAR DOUBLE BLOCK 3/4" RF MODULAR DOUBLE
& BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
WT (5) mm - 2.5 5.8 8.2 11.4 16.4 20.5 25.4 28.6 32.2 36.3 40.9 45.4
MATERIAL High Density Polyethylene PE-100 SDR 11, ISO 4427
MANUFACTURE
WELDING NECK
FLANGES
SOCKET WELD
THREADED
GLOBE
FLANGED BRANCH TEE High Density Polyethylene PE-100, ISO 4427 LONG SPIGOT
LJ STUB ENDS High Density Polyethylene PE-100, ISO 4427 LONG SPIGOT
PIPE BENDS
MITER ELBOWS
8 SWLT SWLT RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
10
DN"
SWLT SWLT RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
12 SWLT SWLT RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE
14 SWLT SWLT RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
16 SWLT SWLT RTEE RTEE RTEE RTEE RTEE STEE SWLT SADDLE BRANCH HDPE100
18 SWLT SWLT RTEE RTEE RTEE RTEE STEE WLET WELDOLETS
20 SWLT SWLT MANF STD RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS
24 SWLT SWLT RTEE RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS
SCHEDULE N° - - - 40 40 40 40 40 40 40
MATERIAL A333 Gr.6 SMLS + PP LINED (3)
MANUFACTURE
SOCKET WELD
THREADED
CHECK VC1020
LJ STUB ENDS
PIPE BENDS
MITER ELBOWS
HEADER SIZE
2
DN"
10 TLET THREDOLETS
12 SLET SOCKOLETS
3 mm
Rating & Facing
150 # RF 125 AARH
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 19,6 ---- ----
S.W. FITTINGS LF2 9000# LF2 6000# SPACERS & BLINDS A516 Gr 70 50 19.2 ---- ----
THDD FITTINGS LF2 6000# LF2 3000# -- TEMP. STRAINERS AISI 316 100 17.6 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 15.8 ---- ----
NIPPLES
SCHEDULE N° - XXS 160 160 160 80 STD STD STD STD STD STD STD STD STD STD STD XS XS
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 150# - RF125 AARH
FLANGES
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 150# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (4)
BALL VBA1010,VBA1510(6) VBA1030,VBA1530(6)
FB VBA1110(6),VBA1610(5,6) VBA1130(6),VBA1630(5,6)
VALVES
4
HEADER SIZE
18 NOTE 1 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS A350 LF2
36 RTEE RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS A350 LF2
NOTES: 3) Ball valves may be used to 200°C only and as restricted by the press/temp.
1) Use flanged branch fittings for TW, PI & flanged valve only. limitations of the soft materials within the construction of the valves
Use TLET for hydrotest vents & drains only. 4) Bolting shall be zinc coating (hot-dip) to ISO 1461.
2) DELETED 5) To be used only when indicated on P&ID's
6) High temp valves >=200C
7) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development 4
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 2 AM Jan-2005
SERVICE : (PM)- Sweet LPG, (PW)- Produced Water, (TG)- Treated Gas, (VT)- Vessel Trim
A65
CORR.ALLOWANCE
3 mm
Rating & Facing
150 # RF 125 AARH
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD.V.SS.0018.000 RED. THDD FLG.S --- API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD.V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 14.2 ---- ----
S.W. FITTINGS SPACERS & BLINDS A516 Gr 70 100 13.8 ---- ----
THDD FITTINGS TEMP. STRAINERS AISI 316 200 13.0 ---- ----
NORMAL (from pipe) 300 10.0 ---- ----
NIPPLES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 150# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (4)
BALL
FB
VALVES
GLOBE
CHECK
PIPE BENDS
MITER ELBOWS
HEADER SIZE
NOTES:
SEE SHEET 1 FOR NOTES
Company's sole property document . Company will protect his right by law.
CLASS : A65
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP (SEAL WELD AFTER
TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
SOCKOLET+PBE NIP
+SW FLG (1.5")
RF SW FLANGE + PBE NIP
SOCKET WELD TEE WELDOFLANGE (2")
EQUAL OR REDUCING
HEADER SIZE 3/4" to 1 1/2" HEADER SIZE 2" >= WELDOLET+FLG (3")
(VENT 1.5" - 3")
VDB3010(<200C)
3/4" RF MODULAR DOUBLE BLOCK 3/4" RF MODULAR DOUBLE
VDB3510(>200C) BLOCK & BLEED VALVE
& BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
SOCKET 3/4" RF WELDOFLANGE
WELD TEE EQUAL OR
3/4" RF WN FLANGE
REDUCING
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RF MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" 300 RF SW
FLANGE (TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
External Diam. mm - 16.0 25.0 30.0 44.5 57.0 --- 88.9 108.0 159.0 219.1 267.0 323.9 368.0 419.1 457.2 508.0 610.0 - -
MATERIAL Cu/Ni 90-10 (EEMUA 144) Cu/Ni 90-10 (EEMUA 144)
MANIFACTURE SMLS WLDD
COMPOSITE WELDING NECK A350 LF2 +Cu/Ni 90-10 150 RF (EEMUA 145 LONG) (note 4,7)
FLANGES
COMPOSITE SLIP ON A350 LF2 +Cu/Ni 90-10 150# RF (EEMUA 145) (3,7)
THREADED
10 SLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE Cu/Ni 90-10
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE Cu/Ni 90-10
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE Cu/Ni 90-10
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS Cu/Ni 90-10
36 SLET SOCKOLETS
NOTES:
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
COUNTRY: 0 1 2 3 4 5
AGIP KCO AREA: DOC. No.
PLANT: KE01.00.000.KD.P.ST.0001.000
Sheet Compiled Date
KDPC 2 TM Jan-2005
3) Deleted
5) Support for Cu/Ni pipework should be lined with a soft packing strip or pad. Free of ammoniacal compounds to
prevent chafing and undue stressing. In addition the lining will provide insulation between ferrous and CuNi parts.
8) For connecting valves with NPT female thread to pipe, use adaptor SW x male NPT. (For typical assembly detail see Page 7)
Company's sole property document . Company will protect his right by law.
CLASS : A81
HYDROSTATIC TEST DRAIN/VENT
EQUAL SW TEE
REDUCING SW TEE
THREDOLET
FOR HYDROSTATIC TEST VENT, USE ABOVE ASSEMBLY WITH PORT POINTING UPWARDS
20-48 2
FLANGED FF VALVE >48 3
INTEGRAL SO FLANGE FF
SOCKOLET
SCREWED END VALVE
WELDOLET
FLANGED FF VALVE
Hdr (in) Drain (in)
12-18 2
INTEGRAL SO FLANGE FF COMPOSITE BLIND FLANGE FF 20-48 3
>48 4
INSTRUMENTS
PIPING
3/4" SCREWED END VALVE
HEADER 3/4"
INSTRUMENTS
PIPING
3/4" SCREWED END VALVE
INSTRUMENTS
INSTRUMENTS
PIPING
INSTRUMENTS
1 PIPING
2
3
4
INST.
TYPICAL
1) NPT ISOLATING VALVES
2) ADAPTOR FEMALE SW x 1/2"NPT FEMALE
3) PIPE PBE 100mm OR 200mm LONG 16mm
4) ADAPTOR FEMALE SW x 1/2"NPT MALE
PIPE
SCHEDULE N° - 80s 80s 80s 80s 40S 40S 40S 80S 80S 100 100 100 100 100 100 100 100 1.775
MATERIAL A312 Gr. TP316/316L A358 Gr. TP316/316L
MANUFACTURE SMLS EFW
WELDING NECK A182 F316/316L / 900# RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 182 F316/316L / 900# - RTJ
GASKETS 316 ST ST OVAL RING
STUD BOLTS & NUTS A193 Gr B8M Class 2 / A194 Gr 8M
BALL TEBW VBA9738, VBA9938 (4)
FLG RB VBA15021 VBA9038 (5)
14
DN"
NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A182 F316/L
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A182 F316/L
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS
SLET SOCKOLETS
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RTJ WN FLG 20-48 3
FLG BALL VALVE RTJ BLIND FLANGE
RTJ BLIND FLG >48 4
VDB15021(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL) (ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RTJ WN FLANGE
(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SCHEDULE N° - XXS 160 160 160 160 160 120 120 120 120 120 120 120 120 120 120 1.713" 1.834" 1.955 2.255
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 900# - RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 900# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL TEBW VBA9730, VBA9930 (6)
FLG RB VBA15010 VBA9030 (7)
VALVES
10 NLEP RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
14 NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
16
DN"
18 WLET RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS
36 RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RTJ WN FLG 20-48 3
FLG BALL VALVE RTJ BLIND FLANGE
RTJ BLIND FLG >48 4
VDB15010(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RTJ WN FLANGE
(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(LR)- Refrigeration Liquid, (ML)- Methanol, (OW)- Oily Water,(PO)- Product Oil,
ITEM 1.5 mm
(TG)- Treated Gas, (VT)- Vessel Trim,
Rating & Facing 900 # RTJ
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -46 ÷ 38 153.0 340 111.2
S.W. FITTINGS LF2/6000# LF2/3000# SPACERS & BLINDS A516 Gr 70 50 150.1 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 139.1 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 135.7 ---- ----
NIPPLES
SCHEDULE N° - 160 80 80 80 80 80 120 120 120 120 120 120 120 120 120 120
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 900# - RTJ
FLANGES
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 900# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(3)
BALL TEBW VBA9730, VBA9930 (6)
FLG RB VBA15010,VBA15510(8) VBA9030 (6),VBA9530(8)
FLG FB VBA15110(5),VBA15610(5,8) VBA9130(5,6),VBA9630(5,8)
VALVES
10 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14
DN"
NOTE 1
2 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A350 LF2
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
TLET THREDOLETS A350 LF2
Company's sole property document . Company will protect his right by law.
CLASS : D13
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP (SEAL WELD AFTER
TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
HEADER SIZE 3/4" to 1 1/2" HEADER SIZE 2" >= WELDOLET+FLG (3")
(VENT 1.5" - 3")
VDB15010(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
VDB15510(>200C) BLOCK & BLEED VALVE
BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
SW TEE EQUAL OR WELDOFLANGE
REDUCING 3/4" RTJ WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
0 (WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SCHEDULE N° - 80s 80s 80s 80s 40S 40S 40S 80S 80S 100 100 100 100 100 100 100 100
MATERIAL A312 Gr. TP316/316L A358 Gr. TP316/316L
MANUFACTURE SMLS EFW
WELDING NECK A182 F316/316L / 900# RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 182 F316/316L / 900# - RTJ
GASKETS 316 ST ST OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(6)
BALL VBA15015 VBA9035
FB VBA15115(5) VBA9135(5)
VALVES
14
DN"
NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A182 F316/L
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A182 F316/L
TLET THREDOLETS
SLET SOCKOLETS
NOTES: 4) Ball valves may be used to 200°C only and as restricted by the press/temp.
1) Use flanged branch fittings for TW, PI & flanged valve only. limitations of the soft materials within the construction of the valves
2) All 316 material must be dual certified 316/316L 5) To be used only when indicated on P&ID's
3) DELETED 6) Bolting shall be zinc coating (hot-dip) to ISO 1461.
7) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
CLASS : D15
HYDROSTATIC TEST VENTS & DRAINS
3/4" RTJ BLIND FLANGE 3/4" RTJ BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING 3/4" RTJ WN FLANGE 3/4" RTJ WELDOFLANGE
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RTJ WN FLG 20-48 3
FLG BALL VALVE RTJ BLIND FLANGE
RTJ BLIND FLG >48 4
VDB15015(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(RG)- Raw Gas (Sour), (RO)- Raw Oil, (VT)- Vessel Trim, (WF)- Well Fluid, (WW)- Waste Water
ITEM 6 mm
(RS)- Sewage (Raw), (RW)- Raw Water, (HC)- High Pressure Condensate Rating & Facing
SOUR SERVICE
900 # RTJ
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 153.0 ---- ----
S.W. FITTINGS SPACERS & BLINDS A516 Gr 70 50 150.1 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 139.1 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 135.7 ---- ----
NIPPLES
SCHEDULE N° - XXS XXS XXS XXS XXS XXS 160 140 140 140 140 140 120 120 120 1.86 2.10 2.455
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 900# - RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 900# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (7)
BALL TEBW VBA9750, VBA9950(8)
FLG RB VBA15022 VBA9050
VALVES
10 NLEP RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
26 RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS
NOTES: 6) DELETED
1) Use flanged branch fittings for TW, PI & valved connections only. 7) Bolting shall be zinc coating (hot-dip) to ISO 1461.
2) DELETED. 10) For OFFSHORE TE valves to be used above 8" 8) To be used only when indicated on P&ID's
3) For orifice flange assembly use 1/2" PBE nipple & flange in Alloy 825 9)For Offshore flanged valves to be used only when strictly required (ref. 3.6.5.3).
4) All materials shall meet the requirements of spec KE01.00.000.KD.V.SS.0007.000TE valves shall be used above 8".
5) DELETED 10) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
CLASS : D17
HYDROSTATIC TEST VENTS & DRAINS
1" RTJ BLIND FLANGE 1" RTJ BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING 1" RTJ WN FLANGE 1" RTJ WELDOFLANGE ( * TYP)
WELDOFLANGE
(1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING
WELDOLET+FLG (3")
HEADER SIZE 1" to 1 1/2" HEADER SIZE 2" >=
(VENT 1.5" - 3")
VDB15022(<200C)
1" RTJ MODULAR DOUBLE 1" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
1" RTJ WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 1" RTJ WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION (ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RTJ WN FLANGE Note 3)(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use 1/2" sch 160 pipe & flange in 316/316L SS or Inc 825 (See Notes 5 & 6 sheet 2)
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SCHEDULE N° - 40S 40S 10S 40S 80S 80S 80S 80S 120 120 120 120 120 120 120 120
MATERIAL B423 N08825 (Alloy 825)
MANUFACTURE SMLS/WELDED
WELDING NECK B564 N08825 / 900# RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND B564 N08825 / 900# RTJ
GASKETS INC 825 OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL TEBW VBA9737, VBA9937(6,7)
FLG RB VBA15017 VBA9037
FLG FB VBA15117 (6) VBA9137(6,7)
VALVES
18 WLET RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE B564N08825
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS B564N08825
30 TLET THREDOLETS
36 SLET SOCKOLETS
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RTJ WN FLG 20-48 3
FLG BALL VALVE RTJ BLIND FLANGE
RTJ BLIND FLG >48 4
VDB15017(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL) (ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RTJ WN FLANGE
(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SCHEDULE N° - 40S 40S 40S 40S 10S 40S 40S 40S 80S 60 60 60 80 80 80 80 80 1.204 1.289 1.549
MATERIAL B444 N06625 GR 1 (Alloy 625)
MANUFACTURE SMLS/WELDED
WELDING NECK B564 N06625 / 900# RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND B564 N06625 / 900# RTJ
GASKETS INC 625 OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL TEBW VBA9737, VBA9937(6,7)
FLG RB VBA15017 VBA9037
FLG FB VBA15117 (6) VBA9137(6,7)
VALVES
10 NLEP RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE B366 WPNCMC
12 NOTE 1
RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
18 WLET
RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE B564N06625
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS B564N06625
36 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLET NIPOLETS THDD
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RTJ WN FLG 20-48 3
FLG BALL VALVE RTJ BLIND FLANGE
RTJ BLIND FLG >48 4
VDB15017(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RTJ WN FLANGE
(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SCHEDULE N° - XXS 160 160 160 160 160 120 120 120 120 120 120 120 120 120 120
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 900# RTJ
FLANGES
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 900# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL TEBW VBA9730, VBA9930 (5)
FLG RB VBA15010 VBA9030 (5)
VALVES
TLET
10 RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14 NOTE 1
DN"
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A350 LF2
18 WLET RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEB NIPOLETS BW A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
HEADER SIZE 3/4" to 1 1/2" HEADER SIZE 2" >= WELDOLET+FLG (3")
(VENT 1.5" - 3")
VDB15010(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
SW TEE EQUAL OR WELDOFLANGE
REDUCING 3/4" RTJ WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL) (ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RTJ WN FLANGE
(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A350 LF2 with ALLOY 625 clad / 900# RTJ Note 4
GASKETS ALLOY 625 OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(2)
BALL VBA15117 VBA9037,VBA9081(5)
FB VBA9137(5),VBA9181(5)
VALVES
14 SWLT
RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
NOTE
16 1,6
RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS Note 4,6
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS
30 TLET THREDOLETS
36 SLET SOCKOLETS
NOTES: 6) Valves/piping above certain size may be economical in solid alloy 625.
1) Use flanged branch fittings for TW, PI & valved connections only. Economic selection to be made during detail engineering.
2) Bolting shall be zinc coating (hot-dip) to ISO 1461. 7) Cladding, welding and NDT shall comply with requirements of
3) A420 WPL6 with ALLOY 625 clad or sollid Alloy 625 size dependant spec. KE01.00.000.KD.V.SS.0007.000 and KE01.00.000.KD.V.SS.0018.000 resp.
4) A350 LF2 with ALLOY 625 clad or sollid Alloy 625 size dependant 8) Cladding thickness shall be 3mm minimum of alloy 625
5) Top entry and full bore to be used only when indicated on P&ID's 9) Maximum Fe dilution 3mm from fusion zone shall be 5%
10) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
CLASS : D82
HYDROSTATIC TEST VENTS & DRAINS
3/4" RTJ BLIND FLANGE 3/4" RTJ BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING 3/4" RTJ WN FLANGE 3/4" RTJ WELDOFLANGE
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RTJ WN FLG 20-48 3
FLG BALL VALVE RTJ BLIND FLANGE
RTJ BLIND FLG >48 4
VDB15017(<200C)
3/4" RTJ MODULAR DOUBLE
3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE
BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use 1/2" sch 160 pipe & flange in ALLOY 625
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SCHEDULE N° - 40S 40S 40S 40S 40S 40S 40S 40S 40S 60 60 60 60 60 60 60 60 1.20"
MATERIAL A312 Gr. TP316/316L A358 Gr. TP316/316L
MANIFACTURE SMLS EFW
WELDING NECK A182 F316/F316L / 600# RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A182 F316/F316L / 600# RTJ
GASKETS 316 ST ST OVAL RING
STUD BOLTS & NUTS A193 Gr B8M Class 2 / A194 Gr 8M
BALL BWTE VBA6738, VBA6938 (4)
FLG RB VBA6021 VBA6138 (5)
FLG FB VBA6121(4) VBA6038(4,5)
VALVES
14
DN"
NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A182 F316/L
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A182 F316/L
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS
SLET SOCKOLETS
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RTJ WN FLG 20-48 3
FLG BALL VALVE RTJ BLIND FLANGE
RTJ BLIND FLG >48 4
VDB6021(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(GY)- Glycol, (ML)- Methanol, (PL)- LPG (Sour), (PO)- Product Oil, (RG)- Raw Gas (Sour),
ITEM 3 mm
(RO)- Raw Oil, (TG)- Treated Gas, (VT)- Vessel Trim, (WF)- Well Fluid Rating & Facing
SOUR SERVICE
600 # RTJ
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -46 ÷ 38 102.0 ---- ----
S.W. FITTINGS SPACERS & BLINDS A516 Gr 70 50 100.0 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 92.7 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 90.6 ---- ----
NIPPLES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL BWTE VBA6730, VBA6930 (7)
FLG RB VBA6010, VBA6510(8) VBA6030 (9), 6530 (8,9)
VALVES
10 NLEP RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
14
DN"
NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
18 WLET RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
28 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RTJ WN FLG 20-48 3
FLG BALL VALVE RTJ BLIND FLANGE
RTJ BLIND FLG >48 4
VDB6010(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
VDB6510(>200C)
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION (ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(FH)- HP Flare, (GR)- Refrigeration Gas, (GY)- Glycol, (LR)- Refrigeration Liquid,
ITEM 1.5 mm
(ML)- Methanol,(PM)- Sweet LPG, (PO)- Product Oil, (TG)- Treated Gas, (VT)- Vessel Trim,
Rating & Facing 600 # RTJ
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -46 ÷ 38 102.0 ---- ----
S.W. FITTINGS LF2/6000# LF2/3000# SPACERS & BLINDS A516 Gr 70 50 100.0 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 92.7 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 90.6 ---- ----
NIPPLES
SCHEDULE N° - 160 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANIFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 600# - RTJ
FLANGES
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (3)
BALL BWTE VBA6730, VBA6930 (4)
FLG RB VBA6010, VBA6510 (5) VBA6030 (6), VBA6530(4,5)
VALVES
10 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14
DN"
NOTE 1
2 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A350 LF2
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
HEADER SIZE 3/4" to 1 1/2" HEADER SIZE 2" >= WELDOLET+FLG (3")
(VENT 1.5" - 3")
VDB6010(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
VDB6510(>200C) BLOCK & BLEED VALVE
BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
SOCKET WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION (ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SCHEDULE N° - 40S 40S 40S 40S 40S 40S 40S 40S 40S 60 60 60 60 60 60 60 60
MATERIAL A312 Gr. TP316/316L A358 Gr. TP316/316L
MANIFACTURE SMLS EFW
WELDING NECK A182 F316/F316L / 600# RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A182 F316/F316L / 600# RTJ
GASKETS 316 ST ST OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (6)
BALL VBA6015 VBA6035
FB VBA6115(5) VBA6135(5)
VALVES
14
DN"
NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A182 F316/L
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A182 F316/L
TLET THREDOLETS
SLET SOCKOLETS
NOTES: 4) Ball valves may be used to 200°C only and as restricted by the press/temp.
1) Use flanged branch fittings for TW, PI & flanged valve only. limitations of the soft materials within the construction of the valves
2) All 316 material must be dual certified 316/316L 5) To be used only when indicated on P&ID's
3) DELETED 6) Bolting shall be zinc coating (hot-dip) to ISO 1461.
7) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
CLASS : C15
HYDROSTATIC TEST VENTS & DRAINS
3/4" RTJ BLIND FLANGE 3/4" RTJ BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING 3/4" RTJ WN FLANGE 3/4" RTJ WELDOFLANGE
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RTJ WN FLG 20-48 3
FLG BALL VALVE RTJ BLIND FLANGE
RTJ BLIND FLG >48 4
VDB6015(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL) (ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RTJ WN FLANGE
(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(RG)- Raw Gas (Sour), (RO)- Raw Oil, (TG)- Treated Gas, (VT)- Vessel Trim,
ITEM 6 mm
Rating & Facing
SOUR SERVICE
600 # RTJ
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 102.0 ---- ----
S.W. FITTINGS SPACERS & BLINDS A516 Gr 70 50 100.0 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 92.7 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 90.6 ---- ----
NIPPLES
SCHEDULE N° - XXS XXS XXS 160 160 120 120 100 100 100 100 100 100 100 1.337 1.417
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANIFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 600# - RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (8)
BALL BWTE VBA6750, VBA6950 (9)
FLG RB VBA6022, VBA6522 (10) VBA6050 (11), VBA6550 (10)
VALVES
10 NLEP RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
14 NOTE
DN"
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
26 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS
28 WLET RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS
NOTES: 7) 28" pipe is to API 5L X60 for use in inlet oil line. Fittings to be same grade.
1) Use flanged branch fittings for TW, PI & valved connections only. 8) Bolting shall be zinc coating (hot-dip) to ISO 1461.
2) DELETED. 3) For orifice flange ass'y use 1/2" BBE nipple & flange 9) To be used only when indicated on P&ID's
3) For orifice flange ass'y use 1/2" PBE nipple & flange in Alloy 825 10) High Temperature valves
4) All materials shall meet the requirements of spec KE01.00.000.KD.V.SS.0007.00011) For OFFSHORE flanged valves to be used only when strictly
5, 6) DELETED required (ref. 3.6.5.3). TE valves shall be used above 8".
12) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
CLASS : C17
HYDROSTATIC TEST VENTS & DRAINS
1" RTJ BLIND FLANGE 1" RTJ BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING 1" RTJ WN FLANGE 1" RTJ WELDOFLANGE ( * TYP)
WELDOFLANGE
(1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING
WELDOLET+FLG (3")
HEADER SIZE 1" to 1 1/2" HEADER SIZE 2" >=
(VENT 1.5" - 3")
VDB6022(<200C)
1" RTJ MODULAR DOUBLE 1" RTJ MODULAR DOUBLE
VDB6522(>200C)
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
1" RTJ WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 1" RTJ WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION (ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RTJ WN FLANGE Note 3 (TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use 1/2" sch 160 pipe & flange in Alloy 825 (See Notes 5 & 6 sheet 2)
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(5)
BALL BWTE VBA6730, VBA6930 (7)
FLG RB VBA6010 VBA6030 (7),
VALVES
10 NLEP RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE (9) A420 WPL6
14
DN"
NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
18 WLET RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS PE A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
TLET THREDOLETS
SLET SOCKOLETS
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RTJ WN FLG 20-48 3
FLG BALL VALVE RTJ BLIND FLANGE
RTJ BLIND FLG >48 4
VDB6010(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 694 F60 - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(1)
BALL VBA6030
VALVES
GLOBE
CHECK
PIPE BENDS
MITER ELBOWS
4
HEADER SIZE
14
DN"
NOTES:
1) Bolting shall be zinc coating (hot-dip) to ISO 1461
2) All materials shall meet the requirements of spec
KE01.A1.000.KD.P.ST.0001.000 & KE01.00.000.KD.V.SS.0007.000
3) Corresponds with ISO 3183-3, Annex A
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development 0 1 2 3
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 1 AM Jun-2004
SERVICE :
C21
CORR.ALLOWANCE
ITEM 1.5 mm
(RW)-Raw Water/Technical Water, (VT)- Vessel Trim,
Rating & Facing 600 # RTJ
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S A350LF2 API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 102.0 ---- ----
S.W. FITTINGS LF2/6000# LF2/3000# SPACERS & BLINDS A516 Gr 70 50 100.0 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 92.7 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- ---- ---- ---- ----
NIPPLES
SCHEDULE N° - 160 80 80 80 80 80 80 80 80 80 80 80 80 80 80 80
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANIFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 600# - RTJ
FLANGES
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (3)
GATE VG8050,VG8051,VG8052 VG6060
Note 2
VALVES
10 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14
DN"
NOTE 1
2 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A350 LF2
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
NOTES: .
1) Use flanged branch fittings for TW only.
2) Use VG8051 & VG8052 in vent, drain & instrument assembly.
3) Bolting shall be zinc coating (hot-dip) to ISO 1461.
Company's sole property document . Company will protect his right by law.
CLASS : C21
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP
(SEAL WELD AFTER TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION (ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (3)
GATE VG8050,VG8051,VG8052 VG6070
VG6050 Note 4
VALVES
10 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14
DN"
NOTE 1
2 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A350 LF2
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS A350 LF2
36 RTEE RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS A350 LF2
NOTES:
1) Use flanged branch fittings for TW only.Use TLET for hydro test vents only.
2) Use VG8051/2 in vent, drain & instrument assembly.Deleted
3) Bolting shall be zinc coating (hot-dip) to ISO 1461.
4) Use flanged valves for vent and drain assembly only
Company's sole property document . Company will protect his right by law.
CLASS : C25
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP
(SEAL WELD AFTER TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
VDB6050
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
SOCKET WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION (ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND B564 N08825 / 600# RTJ
GASKETS INC 825 OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL BWTE VBA6737, VBA6937 (6)
FLG RB VBA6017 VBA6037 (7)
VALVES
4 RTEE RTEE
DN" HEADER SIZE
18 WLET
RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS B564N08825
30 TLET THREDOLETS
36 SLET SOCKOLETS
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RTJ WN FLG 20-48 3
FLG BALL VALVE RTJ BLIND FLANGE
RTJ BLIND FLG >48 4
VDB6017(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RTJ WN FLANGE
(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(PL)- LPG (Sour), (PW)- Produced Water, (RG)- Raw Gas (Sour), (VT)- Vessel Trim,
ITEM 0 mm
Rating & Facing
SOUR SERVICE
600 # RTJ
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS B564N06625 -45 ÷ 38 103.4 ---- ----
S.W. FITTINGS --- SPACERS & BLINDS B564N06625 50 103.4 ---- ----
THDD FITTINGS --- -- TEMP. STRAINERS --- 100 103.0 ---- ----
NORMAL (from pipe) B444 N06625 -- 150 100.3 ---- ----
NIPPLES
SCHEDULE N° - 40S 40S 40S 40S 10S 10S 10S 40S 40S 20 40S 40S 40 40 40 40 60
MATERIAL B444 N06625 GR 1 (Alloy 625)
MANIFACTURE SMLS/WELDED
WELDING NECK B564 N06625 / 600# RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND B564 N06625 / 600# RTJ
GASKETS INC 625 OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL BWTE VBA6737, VBA6937 (6)
FLG RB VBA6017 VBA6037 (7)
VALVES
4 RTEE RTEE
HEADER SIZE
18 WLET
RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS B564N06625
30 TLET THREDOLETS
36 SLET SOCKOLETS
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RTJ WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RTJ WN FLG 20-48 3
FLG BALL VALVE RTJ BLIND FLANGE
RTJ BLIND FLG >48 4
VDB6017(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL) (ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SLIP ON
LAP JOINT
BLIND A 182 F11 Cl2 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A193 Gr B16 / A194 Gr 2H
GATE VG8090,VG8091,VG8092 VG6090
VG6051 Note 2,3
VALVES
14
DN"
NOTE 1
2 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A182 F11 Cl2
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A182 F11 Cl2
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A182 F11 Cl2
28 RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS A182 F11 Cl2
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS A182 F11 Cl2
NOTES:
1) Use flanged branch fittings for TW only.Use TLET for hydro test vents only.
2) Use VG8091/2 in vent, drain & instrument assembly.Deleted
3) Use flanged valves for vent and drain assembly only
Company's sole property document . Company will protect his right by law.
CLASS : C40
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP
(SEAL WELD AFTER TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
VDB6090
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
SOCKET WELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION (ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL BWTE VBA6730, VBA6930(5)
FLG RB VBA6010 VBA6030
FLG FB VBA6110(5) VBA6130(5)
VALVES
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETS BW A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
NOTES: 3) Ball valves may be used to 200°C only and as restricted by the press/temp.
1) Use flanged branch fittings for TW, PI & flanged valve only. limitations of the soft materials within the construction of the valves
Use TLET for hydrotest vents & drains only. 4) Bolting shall be zinc coating (hot-dip) to ISO 1461.
2) DELETED 5) To be used only when indicated on P&ID's
6)For OFFSHORE flanged valves to be used only when strictly
required (ref. 3.6.5.3). TE valves shall be used above 8".
7) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
CLASS : C65
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP (SEAL WELD AFTER
TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
HEADER SIZE 3/4" to 1 1/2" HEADER SIZE 2" >= WELDOLET+FLG (3")
(VENT 1.5" - 3")
VDB6010(<200C)
3/4" RTJ MODULAR DOUBLE 3/4" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RTJ
SOCKETWELD TEE WELDOFLANGE
EQUAL OR REDUCING 3/4" RTJ WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RTJ SW FLANGE
(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SCHEDULE N° - - - 40 40 40 -- 40 40 40 60 60 60 60 80 80 80 80 - -
MATERIAL A333 Gr.6 SMLS with ALLOY 625 clad A671 CC60 with ALLOY 625 clad
MANUFACTURE SMLS EFW Note 6
WELDING NECK A350 LF2 with ALLOY 625 clad / 600# RTJ Note 4
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A350 LF2 with ALLOY 625 clad / 600# RTJ Note 4
GASKETS ALLOY 625 OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(2)
BALL VBA6017 VBA6037
FB VBA6117(5) VBA6137(5)
VALVES
14 SWLT
RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
NOTE
16 1,6
RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS Note 4,6
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS
30 TLET THREDOLETS
36 SLET SOCKOLETS
NOTES: 6) Valves/piping above certain size may be economical in solid alloy 625.
1) Use flanged branch fittings for TW, PI & valved connections only. Economic selection to be made during detail engineering.
2) Bolting shall be zinc coating (hot-dip) to ISO 1461. 7) Cladding, welding and NDT shall comply with requirements of
3) A420 WPL6 with ALLOY 625 clad or sollid Alloy 625 size dependant spec. KE01.00.000.KD.V.SS.0007.000 and KE01.00.000.KD.V.SS.0018.000 resp.
4) A350 LF2 with ALLOY 625 clad or sollid Alloy 625 size dependant 8) Cladding thickness shall be 3mm minimum of alloy 625
5) Top entry and full bore to be used only when indicated on P&ID's 9) Maximum Fe dilution 3mm from fusion zone shall be 5%
10) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
CLASS : C82
HYDROSTATIC TEST VENTS & DRAINS
1" RTJ BLIND FLANGE 1" RTJ BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING 1" RTJ WN FLANGE 1" RTJ WELDOFLANGE ( * TYP)
1" RTJ BLIND FLANGE 1" FLG BALL VALVE 1" RTJ BLIND FLANGE
1" FLGD BALL VALVE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION (ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" RTJ MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RTJ WN FLANGE Note
3)(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use 1/2" sch 160 pipe & flange in ALLOY 625
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A182 F316/L -120 ÷ 38 49.6 ---- ----
S.W. FITTINGS SPACERS & BLINDS A182 F316/L 50 48.1 ---- ----
THDD FITTINGS -- TEMP. STRAINERS AISI 316 100 42.2 ---- ----
NORMAL (from pipe) A312 TP 316/316L -- 150 38.5 ---- ----
NIPPLES
SCHEDULE N° - 40S 40S 40S 40S 40S 40S 40S 40S 40S 20 20 30 20 STD STD XS XS
MATERIAL A312 Gr. TP316/316L A358 Gr. TP316/316L
MANUFACTURE SMLS EFW
WELDING NECK A182 F316/F316L / 300# RF 125Ra
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A182 F316/F316L / 300# RF 125Ra
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A193 Gr B8M Class 2 / A194 Gr 8M
BALL VBA3021 VBA3038
FB VBA3121(5) VBA3138(5)
VALVES
14
DN"
NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETSPE A182 F316/L
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A182 F316/L
TLET THREDOLETS
SLET SOCKOLETS
NOTES: 4) Ball valves may be used to 200°C only and as restricted by the press/temp.
1) Use flanged branch fittings for TW, PI & flanged valve only. limitations of the soft materials within the construction of the valves
2) All 316 material must be dual certified 316/316L 5) To be used only when indicated on P&ID's
3) DELETED 6) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
3
CLASS : B04
HYDROSTATIC TEST VENTS & DRAINS
3/4" RF BLIND FLANGE 3/4" RF BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING 3/4" RF WN FLANGE 3/4" RF WELDOFLANGE
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RF WN FLG 20-48 3
FLG BALL VALVE RF BLIND FLANGE
RF BLIND FLG >48 4
VDB3021(<200C)
3/4" MODULAR DOUBLE 3/4" MODULAR DOUBLE BLOCK
BLOCK & BLEED VALVE & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(PG)- Process Gas, (PL)- LPG (Sour), (PO)- Product Oil, (RG)- Raw Gas (Sour),
ITEM 3 mm
(RO)- Raw Oil, (SO)- Slop Oil, (VT)- Vessel Trim, (WF)- Well Fluid Rating & Facing
SOUR SERVICE
300 # RF 125 AARH
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S A350LF2 API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS A350LF2 T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -46 ÷ 38 51.0 ---- ----
S.W. FITTINGS SPACERS & BLINDS A516 Gr 70 50 50.0 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 46.3 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 45.1 ---- ----
NIPPLES
SCHEDULE N° - XXS 160 160 160 80 STD STD STD STD STD 40 40 40 40 40 40
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 300# - RF125 AARH
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 300# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL VBA3010,VBA3510(7) VBA3030,VBA3530(7)
FB VBA3110(6),VBA3610(6,7) VBA3130(6),VBA3630(6,7)
VALVES
10 NLEP RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
14
DN"
NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
18 WLET RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETSPE A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
TLET THREDOLETS
SLET SOCKOLETS
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RF WN FLG 20-48 3
FLG BALL VALVE RF BLIND FLANGE
RF BLIND FLG >48 4
VDB3010(<200C)
3/4" MODULAR DOUBLE 3/4" MODULAR DOUBLE BLOCK
VDB3510(>200C) & BLEED VALVE
BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RF WN FLANGE
(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(GY)- Glycol, (HD)- Hot Oil Drain, (HO)- Hot Oil, (LR)- Refrigeration Liquid,
ITEM 1.5 mm
(PM)- Sweet LPG, (PO)- Product Oil, (TG)- Treated Gas, (VT)- Vessel Trim,
Rating & Facing 300 # RF 125 AARH
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -46 ÷ 38 51.0 ---- ----
S.W. FITTINGS LF2/3000# SPACERS & BLINDS A516 Gr 70 50 50.0 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 46.3 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 45.1 ---- ----
NIPPLES
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 300# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(3)
BALL VBA3010,VBA3510(5) VBA3030,VBA3530(5)
FB VBA3110(4),VBA3610(4,5) VBA3130(6),VBA3630(4,5)
VALVES
10 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14
DN"
NOTE 1
2 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A350 LF2
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
SOCKOLET+PBE NIP
+SW FLG (1.5")
RF SW FLANGE + PBE NIP
SOCKET WELD TEE WELDOFLANGE (2")
EQUAL OR REDUCING
HEADER SIZE 3/4" to 1 1/2" HEADER SIZE 2" >= WELDOLET+FLG (3")
(VENT 1.5" - 3")
VDB3010(<200C)
3/4" MODULAR DOUBLE 3/4" MODULAR DOUBLE BLOCK
VDB3510(>200C) & BLEED VALVE
BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
SOCKET WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RF SW FLANGE
(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A182 F316/L -45 ÷ 38 49.6 ---- ----
S.W. FITTINGS SPACERS & BLINDS A182 F316/L 50 48.1 ---- ----
THDD FITTINGS -- TEMP. STRAINERS AISI 316 100 42.2 ---- ----
NORMAL (from pipe) A312 TP 316/316L -- 150 38.5 ---- ----
NIPPLES
SCHEDULE N° - 40S 40S 40S 40S 40S 40S 40S 40S 40S 20 20 30 20 STD STD XS XS
MATERIAL A312 Gr. TP316/316L A358 Gr. TP316/316L
MANUFACTURE SMLS EFW
WELDING NECK A182 F316/F316L / 300# RF 125Ra
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A182 F316/F316L / 300# RF 125Ra
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(6)
BALL VBA3015 VBA3035
FB VBA3115(5) VBA3135(5)
VALVES
14
DN"
NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETSPE A182 F316/L
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A182 F316/L
TLET THREDOLETS
SLET SOCKOLETS
NOTES: 4) Ball valves may be used to 200°C only and as restricted by the press/temp.
1) Use flanged branch fittings for TW, PI & flanged valve only. limitations of the soft materials within the construction of the valves
2) All 316 material must be dual certified 316/316L 5) To be used only when indicated on P&ID's
3) DELETED 6) Bolting shall be zinc coating (hot-dip) to ISO 1461.
7) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
3
CLASS : B15
HYDROSTATIC TEST VENTS & DRAINS
3/4" RF BLIND FLANGE 3/4" RF BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING 3/4" RF WN FLANGE 3/4" RF WELDOFLANGE
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RF WN FLG 20-48 3
FLG BALL VALVE RF BLIND FLANGE
RF BLIND FLG >48 4
VDB3015(<200C)
3/4" MODULAR DOUBLE 3/4" MODULAR DOUBLE BLOCK
BLOCK & BLEED VALVE & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 51.0 ---- ----
S.W. FITTINGS SPACERS & BLINDS A516 Gr 70 50 50.0 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 46.3 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 45.1 ---- ----
NIPPLES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 300# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (7)
BALL VBA3022 VBA3035,VBA3050
FB VBA3122(8) VBA3150(8)
VALVES
14 NOTE 1
DN"
18 WLET RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETSPE A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
30 RTEE RTEE RTEE RTEE RTEE RTEE RTEE STEE SLET SOCKOLETS
NOTES: 5) DELETED
1) Use flanged branch fittings for TW, PI & valved connections only. 6) DELETED
2) DELETED. 7) Bolting shall be zinc coating (hot-dip) to ISO 1461.
3) For orifice flange ass'y use 1/2" PBE nipple & flange in ALLOY 825 8) To be used only when indicated on P&ID's
4) All materials shall meet the requirements of spec KE01.00.000.KD.V.SS.0007.0009) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
3
CLASS : B17
HYDROSTATIC TEST VENTS & DRAINS
1" RF BLIND FLANGE 1" RF BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING 1" RF WN FLANGE 1" RF WELDOFLANGE ( * TYP)
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
WELDOFLANGE
(1.5"-2")
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING
WELDOLET+FLG (3")
HEADER SIZE 1" to 1 1/2" HEADER SIZE 2" >=
(VENT 1.5" - 3")
VDB3022(<200C)
1" MODULAR DOUBLE 1" MODULAR DOUBLE
BLOCK & BLEED VALVE BLOCK & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
1" 300 RF
BUTT WELD TEE WELDOFLANGE
EQUAL OR REDUCING 1" 300 RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RF WN FLANGE Note
3)(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use 1/2" sch 160 pipe & flange in Alloy 825 (See Notes 3 sheet 2)
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 51.0 ---- ----
S.W. FITTINGS SPACERS & BLINDS A516 Gr 70 50 50.0 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 46.3 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 45.1 ---- ----
NIPPLES
SCHEDULE N° - XXS 160 160 160 80 STD STD STD STD STD 40 40 40 40 40 40
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 300# - RF125 AARH
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 300# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(5)
BALL VBA3010 VBA3030
FB VBA3110(6) VBA3130(6)
VALVES
10 NLEP RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE (7) A420 WPL6
14
DN"
NOTE 1 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEP NIPOLETSPE A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
TLET THREDOLETS
SLET SOCKOLETS
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RF WN FLG 20-48 3
FLG BALL VALVE RF BLIND FLANGE
RF BLIND FLG >48 4
VDB3010(<200C)
3/4" MODULAR DOUBLE 3/4" MODULAR DOUBLE BLOCK
BLOCK & BLEED VALVE & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RF WN FLANGE
(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S A350LF2 API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 45.0 ---- ----
S.W. FITTINGS --- SPACERS & BLINDS A516 Gr 70 50 45.0 ---- ----
THDD FITTINGS LF2/3000# Galv. TEMP. STRAINERS AISI 316 65 45.0 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS Galv. ---- ---- ---- ----
NIPPLES
SOCKET WELD
BALL(Note 5) VBA8015
" Y " STRAINERS
90°-45° ELBOWS A 420 Gr.WPL6
CONC.REDUCTIONS A 420 Gr.WPL6
ECC.REDUCTIONS A 420 Gr.WPL6
ELLIPT.CAPS A 420 Gr.WPL6
LJ STUB ENDS
PIPE BENDS
MITER ELBOWS
HEADER SIZE
1½
DN"
RTSC RTSC RTSC STSC RTSC REDUCTION THDD TEE A350 LF2
INSTRUMENTS INSTRUMENTS
3/4" SCREWED GATE VALVE
PIPING PIPING
3/4" SCREWED GATE VALVE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S A350LF2 API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 51.0 310 38.0
S.W. FITTINGS LF2/3000# SPACERS & BLINDS A516 Gr 70 50 50.0 ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS AISI 316 100 46.3 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 45.1 ---- ----
NIPPLES
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 300# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(3)
GATE VG8050,VG8051,VG8052 VG3070
(Note 2)
VALVES
10 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14
DN"
NOTE 1
2 RTEE RTEE RTEE RTEE STEE RTSC REDUCTION THDD TEE
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A350 LF2
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE SWLT SWEEPOLETS
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
NOTES:
1) Use flanged branch fittings for TW only.Use TLET for hydro test vents only.
2) Use VG8051,VG8052 in vent, drain & instrument assembly.
3) Bolting shall be zinc coating (hot-dip) to ISO 1461.
Company's sole property document . Company will protect his right by law.
3
CLASS : B25
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP
(SEAL WELD AFTER TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(PL)- LPG (Sour),(PW)- Produced Water, (RG)- Raw Gas (Sour), (VT)- Vessel Trim,
ITEM 0 mm
Rating & Facing
SOUR SERVICE
300 # RF 125 AARH
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D, NACE MR 01 75
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS B564N08825 -45 ÷ 38 51.7 ---- ----
S.W. FITTINGS --- SPACERS & BLINDS B564N08825 50 51.7 ---- ----
THDD FITTINGS --- -- TEMP. STRAINERS --- 100 51.5 ---- ----
NORMAL (from pipe) B423 N08825 -- 150 50.3 ---- ----
NIPPLES
SCHEDULE N° - 40S 40S 10S 10S 10S 10S 10S 10S 40S 20 30 30 30 30 30 30 40
MATERIAL B423 N08825 (Alloy 825)
MANUFACTURE SMLS/WELDED
WELDING NECK B564 N08825 / 300# RF 125Ra
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND B564 N08825 / 300# RF 125Ra
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/Inc 825 316 CENTERING & Inc 825 INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL VBA3017 VBA3037
FB VBA3117(6) VBA3137(6)
VALVES
2 RTEE STEE
HEADER SIZE
10
DN"
20 WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE TLET THREDOLETS
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
WELDOFLANGE (1.5"-2")
BUTT WELD TEE EQUAL OR RF WN FLANGE
REDUCING WELDOLET+FLG (3")
WELDOFLANGE (1.5"-2")
Hdr (in) Drain (in)
BUTT WELD TEE 0.75-1 line
EQUAL OR REDUCING 1.5-10 1.5 WELDOLET+FLG (3"-4")
12-18 2
RF WN FLG 20-48 3
FLG BALL VALVE RF BLIND FLANGE
RF BLIND FLG >48 4
VDB3017(<200C)
3/4" MODULAR DOUBLE 3/4" MODULAR DOUBLE BLOCK
BLOCK & BLEED VALVE & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
BUTT WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" MODULAR DOUBLE
BLOCK & BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RF WN FLANGE
(TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: ASME B 31.3 ASME B 16.5 / B 16.34
WELDING AND HEAT TREATMENT KE01.00.000.KD..V.SS.0018.000 RED. THDD FLG.S --- API 6D
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.00.000.KD..V.SS.0018.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A516 Gr 70 -45 ÷ 38 51.0 ---- ----
S.W. FITTINGS LF2 9000# LF2 6000# SPACERS & BLINDS A516 Gr 70 50 50.0 ---- ----
THDD FITTINGS LF2 6000# LF2 3000# -- TEMP. STRAINERS AISI 316 100 46.3 ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- 150 45.1 ---- ----
NIPPLES
SCHEDULE N° - XXS 160 160 160 80 STD STD STD STD STD 40 40 40 40 40 40
MATERIAL A333 Gr.6 SMLS A671 CC60 EFW
MANUFACTURE SMLS EFW
WELDING NECK A 350 LF2 / 300# - RF125 AARH
FLANGES
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 300# - RF125 AARH
GASKETS 3.2 mm SPIRAL WOUND TYPE, graphite/316 CENTERING & INNER RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL VBA3010 VBA3030
FB VBA3110(5) VBA3130(5)
VALVES
10 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
SLET
12 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14 NOTE 1
DN"
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE A350 LF2
18 WLET RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE A350 LF2
20 RTEE RTEE RTEE RTEE RTEE RTEE STEE NLEB NIPOLETS BW A350 LF2
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
NOTES: 3) Ball valves may be used to 200°C only and as restricted by the press/temp.
1) Use flanged branch fittings for TW, PI & flanged valve only. limitations of the soft materials within the construction of the valves
Use TLET for hydrotest vents & drains only. 4) Bolting shall be zinc coating (hot-dip) to ISO 1461.
2) DELETED 5) To be used only when indicated on P&ID's
6) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
3
CLASS : B65
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP (SEAL WELD AFTER
TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
RF BLIND FLANGE
RF BLIND FLANGE Hdr (in) Vent (in)
0.75-1 line
1.5-18 1.5
20-48 2 FLGD BALL VALVE
FLGD BALL VALVE >48 3
SOCKOLET+PBE NIP
+SW FLG (1.5")
RF SW FLANGE + PBE NIP
SOCKET WELD TEE WELDOFLANGE (2")
EQUAL OR REDUCING
HEADER SIZE 3/4" to 1 1/2" HEADER SIZE 2" >= WELDOLET+FLG (3")
(VENT 1.5" - 3")
VDB3010(<200C)
3/4" MODULAR DOUBLE 3/4" MODULAR DOUBLE BLOCK
BLOCK & BLEED VALVE & BLEED VALVE
INSTRUMENTS
INSTRUMENTS
PIPING PIPING
3/4" RF WELDOFLANGE
SOCKET WELD TEE
EQUAL OR REDUCING 3/4" RF WN FLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
1/2" MODULAR DOUBLE BLOCK
& BLEED VALVE
PIPING GASES GASES
FULL PENETRATION WELD (TYP)
1/2" RF SW
FLANGE (TYP.)
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
External Diam. mm - 16.0 25.0 30.0 44.5 57.0 --- 88.9 108.0 159.0 219.1 267.0 323.9 368.0 419.1 457.2 508.0 610.0 - -
MATERIAL Cu/Ni 90-10 (EEMUA 144) (8) Cu/Ni 90-10 (EEMUA 144)(8)
MANIFACTURE SMLS WLDD
COMPOSITE WELDING NECK A350 LF2 +Cu/Ni 90-10 300 RF (EEMUA 145 LONG) (note 4,7)
FLANGES
COMPOSITE SLIP ON A350 LF2 +Cu/Ni 90-10 300# RF (EEMUA 145) (3,7)
THREADED
16 RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE Cu/Ni 90-10
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE Cu/Ni 90-10
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS Cu/Ni 90-10
36 SLET SOCKOLETS
NOTES:
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
COUNTRY: 0 1 2 3 4
AGIP KCO AREA: DOC. No.
PLANT: KE01.00.000.KD.P.ST.0001.000
Sheet Compiled Date
KDPC 2 TM Dec-2004
3) Deleted
5) Support for Cu/Ni pipework should be lined with a soft packing strip or pad. Free of ammoniacal compounds to
prevent chafing and undue stressing. In addition the lining will provide insulation between ferrous and CuNi parts.
8) For pipes where EEMUA 144 indicates a max temperature of +38°C, verification in accordance with ASME B31.3 has been
carried out and is suitable for the 75°C max design temperature.
9) For connecting valves with NPT female thread to pipe, use adaptor SW x male NPT. (For typical assembly detail see Page 7)
10) For flanged valves use composite weld neck flanges 300#.
Company's sole property document . Company will protect his right by law.
CLASS : B82
HYDROSTATIC TEST DRAIN/VENT
EQUAL SW TEE
REDUCING SW TEE
THREDOLET
FOR HYDROSTATIC TEST VENT, USE ABOVE ASSEMBLY WITH PORT POINTING UPWARDS
20-48 2
FLANGED FF VALVE >48 3
INTEGRAL SO FLANGE FF
THREDOLET
SCREWED END VALVE
WELDOLET
FLANGED FF VALVE
Hdr (in) Drain (in)
12-18 2
INTEGRAL SO FLANGE FF COMPOSITE BLIND FLANGE FF 20-48 3
>48 4
INSTRUMENTS
PIPING
3/4" SCREWED END VALVE
HEADER 3/4"
INSTRUMENTS
PIPING
3/4" SCREWED END VALVE
INSTRUMENTS
INSTRUMENTS
PIPING
INSTRUMENTS
1 PIPING
2
3
4
INST.
TYPICAL
1) NPT ISOLATING VALVES
2) ADAPTOR FEMALE SW x 1/2"NPT FEMALE
3) PIPE PBE 100mm OR 200mm LONG 16mm
4) ADAPTOR FEMALE SW x 1/2"NPT MALE
PIPE
SCHEDULE N° - XXS XXS XXS XXS XXS XXS XXS XXS XXS 1" 1.25" 1.438" 1.563" 1.75"
MATERIAL A333 Gr.6 SMLS
MANUFACTURE SMLS
WELDING NECK A 350 LF2 / 1500# - RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 1500# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL VBA15010 VBA15030
FB VBA15110(6) VBA15130(6)
VALVES
TLET THREDOLETS
SLET SOCKOLETS
NOTES: 4) Bolting shall be zinc coating (hot-dip) to ASTM A-153. ISO 1461
1) Use flanged branch fittings for TW, PI & flanged valve only. 5) All materials shall meet the requirements of spec KE01.00.000.KD.V.SS.0007.00
2) DELETED 6) To be used only when indicated on P&ID's
3) Ball valves may be used to 200°C only and as restricted by the press/temp. 7) FB inline DBB for instrument isolation eg. LG
limitations of the soft materials within the construction of the valves
Company's sole property document . Company will protect his right by law.
CLASS : E11
HYDROSTATIC TEST VENTS & DRAINS
3/4" RTJ BLIND FLANGE 3/4" RTJ BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING 3/4" RTJ WN FLANGE 3/4" RTJ WELDOFLANGE ( * TYP)
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL) (ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SCHEDULE N° - 80s 80s 80s 80s 160 160 160 120 160
MATERIAL A312 Gr. TP316/316L
MANUFACTURE SMLS
WELDING NECK A182 F316/316L / 1500# RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 182 F316/316L / 1500# - RTJ
GASKETS 316 ST ST OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(6)
BALL VBA15015 VBA15035
FB VBA15115(5) VBA15135(5)
VALVES
TLET THREDOLETS
SLET SOCKOLETS
NOTES: 4) Ball valves may be used to 200°C only and as restricted by the press/temp.
1) Use flanged branch fittings for TW, PI & flanged valve only. limitations of the soft materials within the construction of the valves
2) All 316 material must be dual certified 316/316L 5) To be used only when indicated on P&ID's
3) DELETED 6) Bolting shall be zinc coating (hot-dip) to ISO 1461
7) FB inline DBB for instrument isolation eg. LG
Company's sole property document . Company will protect his right by law.
CLASS : E15
HYDROSTATIC TEST VENTS & DRAINS
3/4" RTJ BLIND FLANGE 3/4" RTJ BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING
3/4" RTJ WN FLANGE 3/4" RTJ WELDOFLANGE ( * TYP)
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SCHEDULE N° - XXS XXS XXS XXS 0.5" 0.625" 0.813" '1.063" 1.375" 1.625" 1.938" 2.125" 2.375"
MATERIAL A333 Gr.6 SMLS
MANUFACTURE SMLS
WELDING NECK A 350 LF2 / 2500# - RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 2500# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(4)
BALL VBA25030
FB VBA25110 VBA25130(6)
VALVES
TLET THREDOLETS
SLET SOCKOLETS
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(ELBOWFLANGE OR EQUAL) RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SCHEDULE N° - 80s 160 160 XXS XXS XXS XXS 0.75" 1.063"
MATERIAL A312 Gr. TP316/316L
MANUFACTURE SMLS
WELDING NECK A182 F316/316L / 2500# RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 182 F316/316L / 2500# - RTJ
GASKETS 316 ST ST OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M(6)
BALL VBA25035
FB VBA25115 VBA25135(5)
VALVES
TLET THREDOLETS
SLET SOCKOLETS
NOTES: 4) Ball valves may be used to 200°C only and as restricted by the press/temp.
1) Use flanged branch fittings for TW, PI & flanged valve only. limitations of the soft materials within the construction of the valves
2) All 316 material must be dual certified 316/316L 5) To be used only when indicated on P&ID's
3) DELETED 6) Bolting shall be zinc coating (hot-dip) to ISO 1461.
Company's sole property document . Company will protect his right by law.
CLASS : F15
HYDROSTATIC TEST VENTS & DRAINS
3/4" RTJ BLIND FLANGE 3/4" RTJ BLIND FLANGE
BUTT WELD TEE EQUAL OR
REDUCING
3/4" RTJ WN FLANGE 3/4" RTJ WELDOFLANGE ( * TYP)
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
(WELDOFLANGE OR EQUAL) (WELDOFLANGE OR EQUAL)
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. or
CONC.REDUCERS
1 1/2" RTJ FLANGED BRANCH FITTING 1 1/2" RTJ FLANGED BRANCH FITTING
RECOMMENDED DIRECTION RECOMMENDED DIRECTION
(ELBOWFLANGE OR EQUAL) (ELBOWFLANGE OR EQUAL)
OF FLOW OF FLOW
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
3. Use sch 160 pipe. Match bore pipe for 1/2" flange end to class flange wall thickness
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
Press. Des.Thk (note 7) mm - - - - 3.8 5.6 6.9 10.2 13.1 19.3 25.2 31.4 37.2 40.9 - - - - - - -
MATERIAL B444 Gr.1 UNS N06625 (note 1) Alloy 625
MANUFACTURE Seamless heavy wall pipe
CONNECTIONS
GASKET (note 2)
STUD BOLTS & NUTS API 6A Class I (Note 6)
GATE
VG100080
VALVES
GLOBE
(note 5)
VGL100080 --
CHECK VC100080
VDB100080
DOUBLE BLOCK AND BLEED --
VDB100081
" Y " STRAINERS
90°-45° ELBOWS B366 WPNCMC (Note 1)
- CONC.REDUCTIONS B366 WPNCMC (Note 1)
1 STEE ECC.REDUCTIONS B366 WPNCMC (Note 1)
11/2 RTEE STEE ELLIPT.CAPS B366 WPNCMC (Note 1)
2 RTEE RTEE STEE LJ STUB ENDS
8 Components Material
HEADER SIZE
10 SWLT RTEE RTEE RTEE STEE STEE STRAIGHT BW TEE Note 1,3
12 RTEE RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE Note 1,3
14 RTEE RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
- TLET THREDOLETS
- SLET SOCKOLETS
NOTES:
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development 0 1 2 3 4
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 2 TM Dec-2004
2) Use of welded connection shall be maximized. API 6A standard flanges shall be used when required. (Note 8)
Use of other types of connections (i.e. hubs) shall be subject to prior approval of Company for design and manufacturer.
Gasket: API 6A Type BX Pressure Energized Ring Gasket Alloy 625
3) B366 WPNCMC
Supplier wall thickness shall be achieved considering the minimum wall thickness (Note 7) plus manufacturer fabrication
wall thickness tolerance.
Final wall thickness will be indicated after HP Pipes contract award
For the following sizes schedule indicated can be considered:
ND 1" schedule 80
ND 1"1/2 schedule 160
ND 2" schedule 160
ND 3" schedule XXS
ND 4" schedule XXS
6) Bolting shall be A453 Gr.660 Gr D material in compliance with NACE MR0175 and
specification KE01.00.000.KD.P.ST.0017.000
8) Flanges shall be supplied with integral transition pieces to match pipe ID/OD.
9) Flanges are available in API 6A 10000 upto sizes 16 3/4" (inc). For nominal pipe size upto 14" (inc),
the following flanges shall be used
Pipe Nominal Size 1" 1"1/2 2" 3" 4" 6" 8" 10" 12" 14"
Flange Size 1 13/16" 1 13/16" 1 13/16" 3 1/16" 4 1/16" 5 1/8" 7 1/16" 9" 11" 11"
Company's sole property document . Company will protect his right by law.
CLASS :P81
PRESSURE ASSEMBLY
DOUBLE BLOCK & BLEED VALVE 1 13/16" FLG
API 6A INST END
VDB 100080
INSTRUMENT
BRANCH FITTING PER BRANCH CHART PIPING
BLIND FLANGE
BLIND FLANGE
TEMPERATURE ASSEMBLY
INSTRUMENTS
PIPING
150 mm
GASKET (Note 2)
STUD BOLTS & NUTS API 6A Class I (Note 5)
GATE
VG150080
VALVES
GLOBE ---
(note 4)
VGL150080
CHECK
VC150080
- TLET THREDOLETS
- SLET SOCKOLETS
NOTES:
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development 0 1 2 3 4
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 2 TM Dec-2004
2) Use of welded connection shall be maximized. API 6A flanges shall be used when required. (Note 7)
Use of other types of connections (i.e. hubs) shall be subject to prior approval of Company for design and manufacturer.
Gasket: API 6A Type BX Pressure Energized Ring Gasket soft iron
3) The indicated wall thickness is inclusive of 10% tolerances on wall thickness as indicated in the
High Pressure specification referenced below.
Calculation have been performed using an allowable stress of 30 ksi
Details are shown in KE01.B4.000.KD.M.RN. 0006 .000 "High pressure pipe ASME B31.3 design report"
Supplier wall thickness shall be achieved considering the minimum wall thickness (Note 6) plus manufacturer fabrication
wall thickness tolerance.
Final wall thickness will be indicated after HP Pipes contract award
5) Bolting shall be A453 Gr.660 Gr D material in compliance with NACE MR0175 and
specification KE01.00.000.KD.P.ST.0017.000
7) Flange geometry in compliance with API6A 15000 - BX flanges shall be derated to design conditions.
Flange manufacturer is required to verify flanges in accordance with specification KE01.B4.000.KD.V.ST.0001.000
and to state suitability for design conditions using API 6A 60K material.
Flanges shall be supplied with integral transition pieces to match pipe ID/OD.
8) Flanges are available in API 6A 15000 upto sizes 7 1/16" (inc). For nominal pipe size upto 10" (inc),
the following flanges shall be used
Pipe Nominal Size 2" 3" 4" 6" 8" 10" 12"
Flange Size 1 13/16" 2 1/16" 2 9/16" 4 1/16" 5 1/8" 7 1/16" 7 1/16"
Company's sole property document . Company will protect his right by law.
CLASS :R81
PRESSURE ASSEMBLY
DOUBLE BLOCK & BLEED VALVE 1 13/16" FLG
API 6A INST END
INSTRUMENT
BRANCH FITTING PER BRANCH CHART PIPING
2-14 2
BLIND FLANGE
2-14 2
BLIND FLANGE
TEMPERATURE ASSEMBLY
INSTRUMENTS
PIPING
150 mm
Press. Des. THK (note 7) mm - - - - 4.94 7.1 8.92 13.15 16.91 24.89 32.4 40.4 47.9 52.6 - - - - - - -
MATERIAL B444 Gr.1 UNS N06625 (Note 1) Alloy 625
MANUFACTURE Seamless heavy wall pipe
CONNECTIONS
GASKET (Note 2)
STUD BOLTS & NUTS API 6A Class I (Note 6)
GATE VG150081
VALVES
GLOBE VGL150081 --
(note 5)
CHECK VC150081
8 Components Material
HEADER SIZE
10 SWLT
SWLT RTEE RTEE RTEE STEE STEE STRAIGHT BW TEE Note 1,3
12 RTEE RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE Note 1,3
14 RTEE RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
- TLET THREDOLETS
- SLET SOCKOLETS
NOTES:
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development - - 2 3 4
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 2 TM Dec-2004
2) Use of welded connection shall be maximized. API 6A flanges shall be used when required. (Note 8)
Use of other types of connections (i.e. hubs) shall be subject to prior approval of Company for design and manufacturer.
Gasket: API 6A Type BX Pressure Energized Ring Gasket Alloy 625
3) B366 WPNCMC
Supplier wall thickness shall be achieved considering the minimum wall thickness (Note 7) plus manufacturer fabrication
wall thickness tolerance.
Final wall thickness will be indicated after HP Pipes contract award
For sizes from 1" to 4" included schedule XXS can be considered
6) Bolting shall be A453 Gr.660 Gr D material in compliance with NACE MR0175 and
specification KE01.00.000.KD.P.ST.0017.000
8) Flange geometry in compliance with API6A 15000 - BX flanges shall be derated to design conditions.
Flange manufacturer is required to verify flanges in accordance with specification KE01.B4.000.KD.V.ST.0001.000
and to state suitability for design conditions using API 6A 60K material.
Flanges shall be supplied with integral transition pieces to match pipe ID/OD.
9) Flanges are available in API 6A 15000 upto sizes 7 1/16" (inc). For nominal pipe size upto 10" (inc),
the following flanges shall be used
Pipe Nominal Size 1" 1"1/2 2" 3" 4" 6" 8" 10"
Flange Size 1 13/16" 1 13/16" 1 13/16" 2 9/16" 2 9/16" 5 1/8" 7 1/16" 7 1/16"
Company's sole property document . Company will protect his right by law.
CLASS :R82
PRESSURE ASSEMBLY
DOUBLE BLOCK & BLEED VALVE 1 13/16" FLG
API 6A INST END
INSTRUMENT
BRANCH FITTING PER BRANCH CHART PIPING
BLIND FLANGE
BLIND FLANGE
TEMPERATURE ASSEMBLY
INSTRUMENTS
PIPING
150 mm
ATTACHMENT 4
A56 (RW)- Raw Water - Pipeline - Above Ground RF -36 +75 10 A333 Gr.6 6.0
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development - 1 F02 F03
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 2 DHDJ Jun-2004
DESIGN CORR
ITEM SERVICE FACING CONDITION PIPING MATERIALALLOW
T - °C P - barg mm
SOUR SERVICE ISO 3183 L415
C40 (RO) - Raw Oil - Below Ground (Design Factor 0.77) RTJ -36 +70 70 (API 5L X60) 6.0
C44 (FG) - Fuel Gas - Below Ground (Design Factor 0.77) RTJ -26 +55 78 ISO 3183 L360 1.5
(API 5L X52)
C45 (FG) - Fuel Gas - Above Ground (Design Factor 0.67) RTJ -26 +75 78 ISO 3183 L360 1.5
(API 5L X52)
C46 (PO) - Oil Export - Below Ground (Design Factor 0.77) RTJ -26 +70 78 ISO 3183 L415 1.5
(API 5L X60)
C47 (PO) - Oil Export - Above Ground (Design Factor 0.67) RTJ -26 +75 78 ISO 3183 L415 1.5
(API 5L X60)
C48 (TG) - Gas Export - Below Ground (Design Factor 0.77) RTJ -26 +55 78 ISO 3183 L415 1.5
(API 5L X60)
C49 (TG) - Gas Export - Above Ground (Design Factor 0.67) RTJ -26 +75 78 ISO 3183 L415 1.5
(API 5L X60)
C56 (RW) - Raw Water - Above Ground RTJ -36 +75 55 A333 Gr 6 6.0
C57 (FG) - Fuel Gas - Below Ground (Load Safety 0.9) Early Works RTJ -20 +60 82 API 5L Gr B 1.5
C58 (FG) - Fuel Gas - (Load Safety 0.6) Early Works RTJ -36 +75 82 A333 Gr6 1.5
ATTACHMENT 5
Note:-
The revision numbers for individual line classes is set different from the main document revision numbers.
This is to facilitate issue of revised classes. With this system only revised classes need issuing rather than all the
classes listed.
Revision
Class
0 1 2 3 4 5 6 7 8
A55 - 28/02/03 26/09/03 30/06/04
A56 - 28/02/03 26/09/03 30/06/04
ATTACHMENT 6
Note:-
For Valve Data Sheets refer to document KE01.00.000.KD.P.TD.0015.000 where standard piping valves are
selected and KE01.C0.000.KD.L.SF.0002.000 (Plug Valves), KE01.C0.000.KD.L.SF.0003.000 (Ball Valves), where
pipeline valves are selected.
SDR. N° - - - - - - - 17 17 - - - - 17 - - - - -
MATERIAL PE 100 ISO 4427
MANIFACTURE
90°-45° ELBOWS
END CAP
COUPLER
CONC.REDUCTIONS
TEES
GASKETS EPDM 4mm Thick
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (Note 2)
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development - 1 2 3
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 1 DHDJ Jun-2004
SERVICE : (RW)- Raw Water - Pipeline - ABOVE GROUND
A56
CORR.ALLOWANCE
ITEM Note 4 6.0 mm
Rating & Facing 150 # RF
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: SNiP 2.04.02-84 /
WELDING AND HEAT TREATMENT KE01.C0.000.KD.L.SS.0012.000 RED. THDD FLG.S --- ASME 16.5 / ISO 14313
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.C0.000.KD.L.SS.0012.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A350LF2 -36 + 75 10 ---- ----
S.W. FITTINGS LF2/3000# -- SPACERS & BLINDS A350LF2 ---- ---- ---- ----
THDD FITTINGS LF2/3000# -- TEMP. STRAINERS --- ---- ---- ---- ----
NORMAL (from pipe) A333 Gr.6 SMLS -- ---- ---- ---- ----
NIPPLES
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 150# RF
GASKETS EPDM 4mm Thick
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M Note 3
PLUG
CHECK
12 TLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
SLET WLET
14 RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
16
DN"
SWLT SWEEPOLETS
NOTES:
1) For orifice assembly use Nipples TOExPE as A15 Material 3) Bolting shall be zinc coating (hot dip) to ISO 1461
4) 6mm corrosion allowance applies to main line ONLY. A 1.5mm corrosion
2) Above Ground (AG) piping bare, UnderGround (UG) piping allowance to be applied after the first flange off the pipeline, to all valves and to
coated in accordance with KE01.C0.000.KD.L.SS.0007.000 size 2" branch connection
Company's sole property document . Company will protect his right by law.
CLASS : A56
HYDROSTATIC TEST VENTS & DRAINS
SOCKET WELD TEE EQUAL OR 3/4" SCRD CAP
(SEAL WELD AFTER TESTING) THREADOLET
REDUCING
3/4" SCRD SOLID PLUG
(SEAL WELD AFTER TESTING)
TOE/POE PIPE
NIPPLE 100mm
3/4" SOCKET WELD X PBE PIPE NIPPLE 3/4" SOCKET WELD X PBE PIPE NIPPLE
SCREWED VALVE SCREWED VALVE
3/4" SCRD SOLID PLUG 3/4" SCRD SOLID PLUG
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
Valve type Ball or Gate dependent on line service. See sheet 1 valves
INSTRUMENTS INSTRUMENTS
PIPING PIPING
150 (typical)
300mm MAX
4" x LINE SIZE ECC. Or
CONC.REDUCERS
PI PI NG
REDUCER
I NST
I NST
150 150
HEADER SIZE 2" HEADER SIZE 3">=
INSTRUMENTS
45°
LIQUIDS LIQUIDS
INST.
NOTES
1. Orifice plate by instruments, block valves, nipples,flanges, bolts & gaskets by piping.
2. Orifice flange to ASME B16.36 except plain hole for weld connection.
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND F60 ASME B16.5 / 600# - RTJ 28"ASME B16.47 SERIES A
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (Note 4)
BALL KE01.C0.000.KD.L.TD.0009
VALVES
PLUG KE01.C0.000.KD.L.TD.0009
CHECK
14
DN"
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS MSS SP 75
SLET SOCKOLETS
WELDOLET+FLG (3")
PIPING
2" RTJ WELDOFLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
SCHEDULE N° - - - - - - - - - - - - - - - - - - 30
MATERIAL ISO 3183 L415
MANIFACTURE SAW (X60)
WELDING NECK
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND
GASKETS
STUD BOLTS & NUTS
BALL
VALVES
PLUG
CHECK
1/2 CONC.REDUCTIONS
3/4 ECC.REDUCTIONS
1 ELLIPT.CAPS
1½ ISOLATION JOINTS
4
HEADER SIZE
14
DN"
20 SWLT SWEEPOLETS
24 WLET WELDOLETS
TLET THREDOLETS
SLET SOCKOLETS
NOTES:
1) For Branch Sizes see Pipeline Class C43 3) All materials impact tested to -26 DegC
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND F60 ASME B16.5 / 600# - RTJ 28"ASME B16.47 SERIES A
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (Note 4)
BALL KE01.C0.000.KD.L.TD.0009
VBA 6010 (1)
VALVES
PLUG KE01.C0.000.KD.L.TD.0009
CHECK
14
DN"
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS MSS SP 75
SLET SOCKOLETS
NOTES:
1) Minumum branch connection off the pipeline to be 2" 3) All materials impact tested to -26 DegC
including vent, drain and PI connections, use weldoflange. 4) Bolting shall be zinc coated (hot dip) to ISO 1461
2) Above Ground (AG) piping bare, UnderGround (UG) piping
coated in accordance with KE01.C0.000.KD.L.SS.0006.000
Company's sole property document . Company will protect his right by law.
CLASS : C43
HYDROSTATIC TEST VENTS & DRAINS
2" RTJ BLIND FLANGE
WELDOLET+FLG (3")
PIPING
2" RTJ WELDOFLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
SCHEDULE N° - - - - - - - - - - - - - - - 0.405
MATERIAL ISO 3183 L360
MANIFACTURE SAW (X52)
WELDING NECK
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND
GASKETS
STUD BOLTS & NUTS
BALL
VALVES
PLUG
CHECK
1/2 CONC.REDUCTIONS
3/4 ECC.REDUCTIONS
1 ELLIPT.CAPS
1½ ISOLATION JOINTS
4
HEADER SIZE
14
DN"
20 SWLT SWEEPOLETS
24 WLET WELDOLETS
TLET THREDOLETS
SLET SOCKOLETS
NOTES:
1) For Branch Sizes see Pipeline Class C45 3) All materials impact tested to -26 DegC
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND F60 ASME B16.5 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (Note 4)
BALL KE01.C0.000.KD.L.TD.0009
VBA 6010 (1)
VALVES
PLUG KE01.C0.000.KD.L.TD.0009
CHECK
14
DN"
20 SWLT SWEEPOLETS
TLET THREDOLETS
SLET SOCKOLETS
NOTES:
1) Minumum branch connection off the pipeline to be 2" 3) All materials impact tested to -26 DegC
including vent, drain and PI connections, use weldoflange. 4) Bolting shall be zinc coated (hot dip) to ISO 1461
2) Above Ground (AG) piping bare, UnderGround (UG) piping
coated in accordance with KE01.C0.000.KD.L.SS.0006.000
Company's sole property document . Company will protect his right by law.
CLASS : C45
HYDROSTATIC TEST VENTS & DRAINS
2" RTJ BLIND FLANGE
WELDOLET+FLG (3")
PIPING
2" RTJ WELDOFLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
SCHEDULE N° - - - - - - - - - - - - - - - - - 0.405
MATERIAL ISO 3183 L415
MANIFACTURE SAW (X60)
WELDING NECK
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND
GASKETS
STUD BOLTS & NUTS
BALL
VALVES
PLUG
CHECK
1/2 CONC.REDUCTIONS
3/4 ECC.REDUCTIONS
1 ELLIPT.CAPS
1½ ISOLATION JOINTS
4
HEADER SIZE
14
DN"
20 SWLT SWEEPOLETS
24 WLET WELDOLETS
TLET THREDOLETS
SLET SOCKOLETS
NOTES:
1) For Branch Sizes see Pipeline Class C47 3) All materials impact tested to-26 DegC
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND F60 ASME B16.5 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (Note 4)
BALL KE01.C0.000.KD.L.TD.0009
VBA 6060 (1)
VALVES
PLUG KE01.C0.000.KD.L.TD.0009
CHECK
14
DN"
18 RTEE RTEE RTEE RTEE RTEE STEE RTSW REDUCTION SW TEE MSS SP 75
24 RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS MSS SP 75
TLET THREDOLETS
NOTES:
1) Minumum branch connection off the pipeline to be 2" 3) All materials impact tested to -26 DegC
including vent, drain and PI connections, use weldoflange.
2) Above Ground (AG) piping bare, UnderGround (UG) piping 4) Bolting shall be zinc coated (hot dip) to ISO 1461
with KE01.C0.000.KD.L.SS.0006.000
Company's sole property document . Company will protect his right by law.
CLASS : C47
HYDROSTATIC TEST VENTS & DRAINS
2" RTJ BLIND FLANGE
WELDOLET+FLG (3")
PIPING
2" RTJ WELDOFLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
SCHEDULE N° - - - - - - - - - - - - - - - - - 0.375
MATERIAL ISO 3183 L415
MANIFACTURE SAW (X60)
WELDING NECK
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND
GASKETS
STUD BOLTS & NUTS
BALL
VALVES
PLUG
CHECK
1/2 CONC.REDUCTIONS
3/4 ECC.REDUCTIONS
1 ELLIPT.CAPS
1½ ISOLATION JOINTS
4
HEADER SIZE
14
DN"
20 SWLT SWEEPOLETS
24 WLET WELDOLETS
TLET THREDOLETS
SLET SOCKOLETS
NOTES:
1) For Branch Sizes see Pipeline Class C49 3) All materials impact tested to -26 DegC
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND F60 ASME B16.5 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (Note 4)
BALL KE01.C0.000.KD.L.TD.0009
VBA 6010 (1)
VALVES
PLUG KE01.C0.000.KD.L.TD.0009
CHECK
14
DN"
16 WLET RTEE RTEE RTEE RTEE RTEE STEE STSW STRAIGHT SW TEE
20 SWLT SWEEPOLETS
TLET THREDOLETS
SLET SOCKOLETS
NOTES:
1) Minumum branch connection off the pipeline to be 2" 3) All materials impact tested to -26 DegC
including vent, drain and PI connections, use weldoflange. 4) Bolting shall be zinc coated (hot dip) to ISO 1461
2) Above Ground (AG) piping bare, UnderGround (UG) piping
coated in accordance with KE01.C0.000.KD.L.SS.0006.000
Company's sole property document . Company will protect his right by law.
CLASS : C49
HYDROSTATIC TEST VENTS & DRAINS
2" RTJ BLIND FLANGE
WELDOLET+FLG (3")
PIPING
2" RTJ WELDOFLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
SCHEDULE N° - - - - - 80 - XS XS XS XS XS XS - - - - - -
MATERIAL A333 Gr.6 SMLS
MANIFACTURE SMLS
WELDING NECK A350 LF2 / 600# - RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A350 LF2 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M Note 3
GATE VG 6060
Note 4
VALVES
PLUG
CHECK
10 WLET RTEE RTEE RTEE STEE RTEE REDUCTION BW TEE A420 WPL6
14
DN"
20 SWLT SWEEPOLETS
24 WLET WELDOLETS
TLET THREDOLETS
SLET SOCKOLETS
NOTES:
1) Above Ground (AG) piping bare, UnderGround (UG) piping 4) 6mm corrosion allowance applies to main line ONLY. A 1.5mm corrosion
coated in accordance with KE01.C0.000.KD.L.SS.0007.000 allowance to be applied after the first flange off the pipeline, to all valves and to
2) Deleted size 2" branch connection
3) Bolting shall be zinc coating (hot dip) to ISO 1461
Company's sole property document . Company will protect his right by law.
COMPANY: Agip KCO Job Revision
PROJECT: Kashagan Field Development - 1 2 3
AGIP KCO ASSET: DOC. No.
Kashagan Field Dev. - Experimental Programme Project KE01.00.000.KD.P.ST.0001.000
SUB-PROJECT: General Sheet Compiled Date
KDPC 1 DHDJ Jun-2004
SERVICE : (FG)- Fuel Gas - BURIED Load Safety 0.9 Early Works
C57
CORR.ALLOWANCE
ITEM 1.5 mm
Rating & Facing 600 # RTJ
REFERENCE SPECIFICATIONS COMPONENTS MAT. CODES: SNiP 2.05.06-85* /
WELDING AND HEAT TREATMENT KE01.C0.000.KD.L.SS.0012.000 RED. THDD FLG.S A350LF2 ASME 16.5 / ISO 14313
PIPING CLASS RED. S.O. FLG.S --- DESIGN CONDITIONS
WELDS EXAMINATION KE01.C0.000.KD.L.SS.0012.000 DRIP RINGS --- T - °C P - barg T - °C P - barg
MATERIALS (if not otherw.stated) ASTM STANDARDS SPECTACLE BLINDS A350LF2 -20 + 60 82 ---- ----
S.W. FITTINGS -- SPACERS & BLINDS A350LF2 ---- ---- ---- ----
THDD FITTINGS -- -- TEMP. STRAINERS --- ---- ---- ---- ----
NORMAL (from pipe) -- -- ---- ---- ---- ----
NIPPLES
SCHEDULE N° - - - - - - - - - - - - - - - - - - -
MATERIAL API 5L Grade B
MANIFACTURE SMLS
WELDING NECK
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND
GASKETS
STUD BOLTS & NUTS
PLUG
CHECK
1/2 CONC.REDUCTIONS
3/4 ECC.REDUCTIONS
1 ELLIPT.CAPS
4
HEADER SIZE
14
DN"
20 SWLT SWEEPOLETS
24 WLET WELDOLETS
TLET THREDOLETS
SLET SOCKOLETS
NOTES:
1) For Branch sizes see piping class C58. 3) Bolting shall be zinc coating (hot dip) to ISO 1461
SCHEDULE N° - - - - - 80 - 80 80 80 - - 60 - - - - 0.75
MATERIAL A333 Grade 6
MANIFACTURE SMLS
WELDING NECK A 350 LF2 / 600# - RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND A 350 LF2 / 600# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (Note 3)
PLUG KE01.C0.000.KD.L.TD.0009
CHECK
12 WLET WLET WLET RTEE RTEE RTEE STEE STSC STRAIGHT THDD TEE
14
DN"
20 SWLT SWEEPOLETS
24 WLET WLET WLET WLET WLET RTEE RTEE RTEE RTEE RTEE RTEE STEE WLET WELDOLETS A350 LF2
NOTES:
1) Minumum branch connection off the pipeline to be 2" 3) Bolting shall be zinc coated (hot dip) to ISO 1461
including vent, drain and PI connections, use weldoflange.
2) Above Ground (AG) piping bare, UnderGround (UG) piping
coated in accordance with KE01.C0.000.KD.L.SS.0007.000
Company's sole property document . Company will protect his right by law.
CLASS : C58
HYDROSTATIC TEST VENTS & DRAINS
2" RTJ BLIND FLANGE
2" WELDOFLANGE
2" WELDOFLANGE
PIPING
2" RTJ WELDOFLANGE
NOTE:- Insulation clearance shall be considered. Where required use pipe nipple to extend.
(* TYP) for weldoflange is to describe flanged reinforced branch connection specified on sheet 1
SCHEDULE N° - - - - - - - - - - - - - - - - - - 30
MATERIAL ISO 3183 L415
MANIFACTURE SAW (X60)
WELDING NECK
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND
GASKETS
STUD BOLTS & NUTS
BALL
VALVES
PLUG
CHECK
1/2 CONC.REDUCTIONS
3/4 ECC.REDUCTIONS
1 ELLIPT.CAPS
1½ ISOLATION JOINTS
4
HEADER SIZE
14
DN"
20 SWLT SWEEPOLETS
24 WLET WELDOLETS
TLET THREDOLETS
SLET SOCKOLETS
NOTES:
1) For Branch Sizes see Pipeline Class C41 3) All materials impact tested to -26 DegC
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND
GASKETS
STUD BOLTS & NUTS
BALL
VALVES
PLUG
CHECK
1/2 CONC.REDUCTIONS
3/4 ECC.REDUCTIONS
1 ELLIPT.CAPS
1½ ISOLATION JOINTS
4
HEADER SIZE
14
DN"
20 SWLT SWEEPOLETS
24 WLET WELDOLETS
TLET THREDOLETS
SLET SOCKOLETS
NOTES:
1) For Branch Sizes see Pipeline Class D61 3) All materials impact tested to -26 DegC
SCHEDULE N° - - - - - 160 - 160 120 120 100 0.689 80 0.752 0.874 0.874" - 0.937 -
MATERIAL ISO 3183 L360 ISO 3183 L360
MANIFACTURE SMLS (X52) SAW (X52)
WELDING NECK F60 ASME B16.5 / 900# - RTJ
FLANGES
SOCKET WELD
THREADED
SLIP ON
LAP JOINT
BLIND F60 ASME B16.5 /900# - RTJ
GASKETS SOFT IRON OVAL RING
STUD BOLTS & NUTS A320 Gr L7M / A194 Gr 7M (Note 4)
BALL KE01.C0.000.KD.L.TD.0009
VALVES
PLUG KE01.C0.000.KD.L.TD.0009
CHECK
14
DN"
20 SWLT SWEEPOLETS
28 TLET THREDOLETS
SLET SOCKOLETS
NOTES: 1) Minumum branch connection off the pipeline to be 2" 3) All materials impact tested to -26DegC
including vent, drain and PI connections, use weldoflange. 4) Bolting shall be zinc coated (hot dip) to ISO 1461
2) Above Ground (AG) piping bare, Subsea (SS) piping 5) 6mm corrosion allowance applies to main line ONLY. A 1.5mm corrosion
coated in accordance with KE01.C0.000.KD.L.SS.0007.000 allowance to be applied after the first flange off the pipeline, to all valves and to
or with KE01.C0.000.KD.L.SS.0006.000 size 2" branch connection
Company's sole property document . Company will protect his right by law.