STP Tender - Budget
STP Tender - Budget
FOR IWC
1. You are requested to submit a proposal to Design, Issue civil drawings & Supply,
Installation, testing & commissioning of Sewage Treatment Plant of subject work.
2. Please note that both the scopes mentioned above should be quoted separately.
3. To enable you to submit a proposal, attached are:
0 i. Overview…………………………………….…. ….… ……. (Section I)
1 ii. Scope of Work………………………………………..……….(Section II)
4. Clarifications / Queries Regarding RFP: No Telephonic correspondence will be entertained.
All clarifications sought should be sent to [email protected]
5. Client reserves the right to refuse any or all applications without assigning any reason
whatsoever.
6. All information submitted will become the property of Client and is non returnable.
7. Location of the Project Area: The site is located at Bangalore.
8. If you request additional information, we would endeavor to provide information
expeditiously, but any delay in providing such information will not be considered a reason
for extending the submission date of your proposal.
9. You are requested to submit your Company profile, Project experience along with your
proposal.
Regards,
R N Joshi
OVERVIEW
The general character and the scope of work to be carried out under this contract is on turnkey
basis excluding major civil works. The BOQ should cover the main equipments for the STP,
however if any other equipment required may be indicated in the BOQ with all technical
parameters and its prices and Specifications and Schedule of Quantities. The Contractor shall
carry out and complete the said work under this contract in every respect in conformity with the
contract documents and with the direction of and to the satisfaction of the Owner’s site
representative. The scope of supply of Sewage treatment plant (STP) shall include design,
detailed engineering of all mechanical and electrical works including piping systems,
instrumentation and supply of equipment to site, storage and erection, testing and
commissioning of STP on turnkey basis and obtaining consent of operation from Pollution
Control Board & also obtaining any other statutory from state agencies. Tenderer shall note
that no extra non-tender items will be allowed while executing the works.
Page - 3
Total STP requirement for the complex is 100m³/day.
b) In line strainer
d) Air Blowers
f) Grease Trap
g) Associated piping systems including valves and associated instrumentation and electrics
etc.
l) Obtaining consent of operation of the Sewage Treatment Plant from statutory authorities and
submissions of O & M Manuals & ‘AS BUILT DRAWINGS”.
The contractor shall carry out the work in accordance with the Drawings, Specifications,
Schedule of Quantities and other documents forming part of the Contract.
The contractor shall be fully responsible for the performance of the selected equipment at the
specified parameters and for the efficiency of the installation to deliver the required end result.
The contractor shall guarantee that the Sewage Treatment Plant as installed shall maintain the
design conditions as described under “Basis of Design” given above.
The contractor shall visit the site before quoting and familiar with site conditions and facilities
available.
Page - 5
6.0 BATTERY LIMITS:
A. Working of system.
B. Flow Chart showing all valves, meters, puddles/inserts symbolically to verify that all
important components are indeed included.
C. Layout drawing.
D. Details of Kitchen Grease Trap.
E. SLD diagram.
STP Vendors to give equipment details with all makes mentioned. Also give plumbing &
electrical details with all makes & SLD on a separate sheet including cost.
Page - 7
PART A:-
BILL OF QUANTITY
No. Description Qty Unit Cost (In INR)
Rate Amount
PART A
1.0 Sewage Treatment Plant
Page - 9
d) Capacity
e) M.O.C: C. I.
6 RETURN SLUDGE PUMP
a) Type: Horizontal centrifugal, self priming.
b) Qty: 2 Nos.
c) Capacity:
d) M.O.C: C. I.
7 MOTOR FOR RETURN SLUDGE PUMP
a) Type: TEFC Sq, cage Induction Motor, Suitable
for 450 volts, 50 heads size, 3 phase A.C supply
with IP 55 protection and Class ‘B’ Insulation
suitable for 430 C ambient temperature.
b) Qty: 2 Nos.
c) Mounting: Foot Mounted
d) Capacity
e) M.O.C: C. I.
8 FILTER FEED PUMP
a) Type: Horizontal centrifugal, Mono block.
b) Qty: 2 Nos.
c) Capacity:
d) M.O.C: C. I.
9 DUAL MEDIA FILTER
a) Type: Vertical, multi media.
b) Qty: 1 No.
c) Capacity:
d) M.O.C: MS internal faces painted with
bituminous paint
10 ACTIVATED CARBON FILTER
a) Type: Vertical, Activated carbon media
b) Qty: 1 No.
c) Capacity
d) M.O.C: MS internal faces painted with
bituminous paint
11 INSTRUMENTATION
a) Pressure Gauge
b) Flow Meter: 1 No
12 ELECTRICAL PANEL
a. Body Thickness: 14 SWG.
b. Doors Thickness: 16 SWG.
c. Base Frame size: 75 mm x 40 mm x4.7 mm thk
d. Construction: Single Front, Cubical fixed
feeders.
e. Finish: Powder Coating.
f. Shade: Siemens Grey
g. Bushbars: Electrolytic Grade Aluminum Busbar
supported on
Epoxy/SMC support
h. Internal Wiring: 660/1100V, PVC insulated
copper flexible wire.
13 BAR SCREEN
a) Type: Rake type, Coarse.
b) Qty: 1 No.
c) M.O.C: MS epoxy Painted.
14 INTERCONNECTING PIPING & VALVES
a) M.O.C: UPVC for pipes & PP for valves.
b) Qty: 1 lot.
15 HYPOCHLORITE DOSING TANK
a) Type: Vertical, open top.
b) Qty: 1 No.
c) Capacity
d) M.O.C: HDPE.
16 HYPOCHLORITE DOSING PUMP
a) Type : Vertical, open top.
b) Qty: 1 No.
c) Capacity
d) M.O.C: PP.
Vendor to consider Routine service / break down
calls for above STP for 2 years of warranty /
defects liability period.
TOTAL PART A IN INDIAN RUPEES
1.0 MAINTENANCE:
Page - 11
SCHEDULE OF EXCLUSION
1. All Civil work is excluded from your scope of work i.e. foundation of packaged type STP.
2. Water & Power required for erection & commissioning.
3. All chemicals and consumable except first charge.
4. Conveyance of raw sewage to the Sewage Treatment Plant & treated sewage.
5. Main Incoming with earthing will be provided to your STP panel.
6. Plant lighting & earthing.
7. Shed for Filters, Blowers & canopy for motors.