Professional Documents
Culture Documents
Physics Practicals
Physics Practicals
MEASURING INSTRUMENTS
1. MEASUREMENT OF LENGTH
For the measurement of length usually meter scales are used with an accuracy upto
millimeters. To measure length say 1/100th of a centimeter (or) 1/100th of a millimeter, it is not
possible to measure accurately using meter scale. Hence the following instruments are used for
more accuracy.
1. Vernier Calipers (Accuracy upto 1/100th of cm)
2. Screw gauge (Accuracy upto 1/100th of mm)
1. VERNIER CALIPERS
Design of the Instrument
It consists of two scales viz, main scale and vernier scale. The main scale is a long steel bar
graduated in inches on the top and in centimeters on the bottom. 10 main scale divisions are equal
to 1cm. The vernier scale has 10 divisions which are equal to 9 main scales divisions. There are
two metal jaws A & B. A is fixed and B is movable which can be fixed at any position using the
screw(s) as shown in figure 1.
Derivation
LC = 1 MSD – VSD
10 MSD = 1 cm
1
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
1 MSD = 1 /10 cm
10 VSD = 9 MSD
1 VSD = 9/10 MSD (or) {9/10} X {1/10}
= 9/100 cm
LC = {1/10- 9/100} cm
= 1/100 cm = 0.01 cm
No Zero Error
To find the zero error of the vernier calipers, the two jaws A
and B brought in contact with each other. If the zero of the vernier
scale coincides with the zero of the main scale then there is no zero
error (Z.E = 0) (fig. 1.1). Hence there is no need to apply zero
correction (Z.C = 0).
2
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
2. SCREW GAUGE
3
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
4
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
If the zero error is 0.04 mm (Positive zero error), then the zero correction is – 0.04 mm,
Correct reading = OR±ZC
= (5.35-0.04) mm
= 5.31 mm
3 . TRAVELLING MICROSCOPE
Fig. 3 Travelling
Microscope.
The main scale is divided into millimeter and half a millimeter. Therefore the value of one
main scale division (MSD) is 0.5 mm. The vernier scale of the travelling microscope is divided into
50 divisions which are equivalent to 49 main scale divisions.
Least count Derivation
LC = 1 MSD – 1 VSD
20 MSD = 1 cm
1 MSD = 1/20 cm
Here 50 VSD = 49 MSD
1 VSD = 49/50 MSD = (49/50) x (1/20) cm 1
VSD = 49/1000 cm LC
= (1/20 – 49/1000) cm
5
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
= 1/1000 cm LC
= 0.001 cm
4. MEASUREMENT OF ANGLES
Fig. 4 Spectrometer.
Spectrometer – Design of the instrument
Spectrometer consists of collimator (c) telescope (T), prism table (p) and vernier table as
shown in fig 4. The collimator consists of a convex lens fixed at one end and a slit of adjustable
width on the other end.
The telescope consists of an objective (O) at one end and an eye piece fixed with the
cross wires on the other end. The prism table consists of two circular disc connected by three
leveling screws. The vernier tables have two verniers VA and VB each having main scale and
vernier scale. Here one main scale division is equal to half a degree. Each vernier scale has 30
divisions, which is equal to 29 main scale divisions.
Initial adjustments
(i) Eye piece adjustment: The eye piece (E) is adjusted until the cross wires are
clearly seen when viewed through the telescope.
(ii) Distant object method: A clear, well defined inverted and diminished image of a
distance object is seen by adjusting the telescope.
(iii) Slit adjustment: The slit is made narrow with the help of the screw, provided
aside of the slit.
(iv) Collimator adjustment: The telescope is brought on line with the collimator. The
slit is illuminated by a source of light. If the image of the slit appears blurred, then
the screw of the collimator is adjusted until a clear image is seen when viewed
6
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
through the telescope. Now the rays of light emerging from the collimator will be
rendered parallel.
(v) Prism table adjustment: The spirit level is placed on the prism table, parallel to
the line joining any two leveling screws. The air bubble in the spirit level is brought
to the centre by adjusting the two screws. It is then placed in a perpendicular
direction and the air bubble is brought at the centre by adjusting the third screw.
Now the prism table will be horizontal.
(vi) Spectrometer base: The base of the spectrometer is adjusted to the horizontal
with the help of the three leveling screws.
Least count
LC = 1 MSD – 1 VSD
1 MSD = ½ degree
30 VSD = 29 MSD
1 VSD = 29/30 MSD
1 VSD = 29/30 x ½ degree
1 VSD = 29/60 degree
LC = (1/2-29/60) degree = (30-29)/60 degree
= 1/60 degree
Since 60’ = 1°
1’ = 1°/60
LC = 1’
Measurement
Before doing any experiment using spectrometer, the above mentioned initial adjustments
have to be made. While performing the experiment, the main scale and vernier scale readings are
noted from both the verniers in VA and VB in degree and minutes.
Fig. 5
7
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Apparatus required
A laser source, laser grating, given particle, screen, scale, etc.
Formula
Explanation of symbols
8
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Theory `
A device for producing spectra by diffraction is known as diffraction grating. While producing
diffraction spectra using the particle, the size of the particle should be comparably equal to the
wavelength of the source. The diffracted wave undergoes constructive and destructive interference
effect. The intensities of the spectra depend up to the diffraction angle. By measuring the diffraction
angle interms of orders of spectra. The wavelength of the given laser source and the size of the
particle can be determined.
Ym Mean
S.No. Order (m) Y2m D21 √𝑌𝑚2 + 𝐷2 d
LHS RHS Ym
9
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
10
Procedure
Result:
10
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
VIVA – VOCE
3. Is the diffraction possible if laser light is replaced by ordinary light for the same particle?
Explain.
4. What happens to the order of spectrum, if the distance between the particle and the screen
is increased?
6. What will happen to the order of spectrum if the size of the particle is decreased?
WORK SHEET
CALCULATIONS:
11
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
WORK SHEET
CALCULATIONS:
12
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
13
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Apparatus required
A laser source, laser grating, screen, scale, etc.
Formula
Explanation of symbols
14
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Theory
A device for producing spectra by diffraction is known as diffraction grating. While producing
diffraction spectra using the particle, the size of the particle should be comparably equal to the
wavelength of the source. The diffracted wave undergoes constructive and destructive interference
effect. The intensities of the spectra depend upto the diffraction angle. By measuring the diffraction
angle interms of orders of spectra. The wavelength of the given laser source and the size of the
particle can be determined.
15
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
10
1 d1 = r1=
2 d2= r2=
Procedure
The laser source and the laser grating are mounted on separate stands as shown in fig.7. A
fixed distance (D) is kept between the laser grating and the screen. The laser source is
switched ON and the beam of laser is allowed to fall on the laser grating. The diffracted beams
are collected on the screen. The diffracted beams are in the form of spots as shown in fig. 7.
In the figure 7, the intensity of the irradiance is found to decrease, from zeroth order to
higher orders, i.e. the first order is brighter than the second order and so on. The positions X1, X2,
X3… of the spots belonging to the first order, second order, third order etc., on either side of the
central maximum are marked on the screen and is noted.
The experiment is repeated for various values of D and the positions of the spots are noted.
Then by using the given formula the wavelength of the source can be calculated and the mean is
taken.
Angle of divergence given the angular spread of the laser beam. A simple diagrammatic
explanation of finding the angle of divergence show in fig. 8.
16
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
WORK SHEET
CALCULATIONS:
17
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Result
VIVA – VOCE
4. What happens to the order of spectrum, if the distance between the particle and the screen
is increased?
18
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
6. What will happen to the order of spectrum if the size of the particle is decreased?
8. What is the principle used in the propagation of light through optical fibres?
19
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Apparatus required
Optical fibre, numerical aperture measurement Jig., scale, etc.
Formula
𝑟
Numerical aperture of the given optical fibre NA = (No unit)
√𝑟 2 +𝑑 2
Acceptance angle ‘θ’max = sin-1 (NA) degrees
Explanation of symbols
Theory
Numerical Aperture (NA) and Acceptance Angle:
It is the light collecting efficiency of the fibre and is the measure of the maximum amount of
light that can be accepted by the fibre. Using Snell’s law mathematically we can say
NA = sin θmax = √n12-n22
20
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Numerical
Length of
Distance between NA Radius of the circular
aperture=
S.No. the given Jig opening and the opening in Numerical
fibre (d) aperture Jig (r) 𝑟
fibre
√𝑟 2 + 𝑑 2
Unit meter X10-3m X10-2m (No Unit)
1.
2.
3.
4.
5.
6.
21
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Procedure
A known length of fibre is taken. One end of the fibre is connected to the laser source and
the other end is connected to the numerical aperture (NA) Jig as shown in fig. 9. The source is
switched ON. The opening in the NA jig is completely opened so that a circular red patch of laser
light is observed on the screen. Now the opening in the NA Jig is slowly closed with the knob
provided, so that at a particular points the circular light patch in the screen just cuts. The radius of
the circular opening (r) of NA Jig at which the circular patch of light just cuts is measured.
The distance between the NA jig opening and the fibre can be measured directly with the
help of the calibration in NA jig. By substituting the values in the given formula the numerical
aperture can be calculated.
The same procedure can be adopted for various distances between the fibre and the
opening of NA jig. The same procedure can be adopted for various length of fibre cable.
By finding the mean of numerical aperture (NA) and substituting it in the given formula the
acceptance angle can be determined.
Result
(i) The Numerical aperture of the given optical fibre = …………. (No unit)
(ii) The acceptance angle of the given optical fibre = …………… Degrees
VIVA – VOCE
2. What is the principle used in the propagation of light through optical fibres?
22
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
WORK SHEET
CALCULATIONS:
23
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
WORK SHEET
CALCULATIONS:
24
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Apparatus required
Traveling microscope, two optically plane glass plates, 45° angle glass plate, given wire (or) thin
paper, sodium vapour lamp, Transformer etc.
Formula
𝑙𝜆
Thickness of the given wire (or) thin sheet of paper is given by t= 2𝛽
Explanation of symbols
l Distance between edge of contact and the wire (or) paper metre
Theory
Two plane glass plates are inclined at an angle by introducing thin materials. (e.g.. hair), forming a
wedge shaped air film. This film is illuminated by sodium light, interference occurs between the two rays,
one reflected from the front surface and the other obtained by internal reflection at the back surface. Since
in the case of a wedge shaped film, thickness of the material remains constant only in direction parallel to
the thin edge of the wedge, straight line fringes parallel to the edge of the wedge are obtained.
26
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
n+5
n+10
n+15
n+20
n+25
n+30
n+35
n+40
n+45
n+50
(ii) To find the distance between the edge of contact and the material of wire (or)
paper. LC = 0.001 cm TR = MSR + (VSC x
LC)
Microscope reading l =R
Position of the Microscope MSR VSC TR 1~R2 x
x 10-2m (Div) x 10-2m 10-2m
Procedure
Two optically plane glass plates are placed one over the other and tied by means of a
rubber band at one end. The given material of wire (or) paper is introduced on the other end, so
27
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
that an airwedge is formed between the plates as shown in fig.10. This set up is placed on the
horizontal bed plate of the traveling microscope.
Light from the sodium vapour lamp (S) is rendered parallel by means of a condensing lens
(L). The parallel beam of light is incident on a plane glass plate (G) inclined at an angle of 45º and
gets reflected. The reflected light is incident normally on the glass plates in contact Pc. Interference
taken place between the light reflected from the top and bottom surfaces of the glass plates and is
viewed through the traveling microscope (M). Hence large number of equally spaced dark and
bright fringes are formed which are parallel to the edge of contact (fig. 11).
The microscope is adjusted so that the bright (or) dark fringe near the edge of contact is
made to coincide with the vertical cross wire and this is taken as the nth fringe. The reading from
the horizontal scale of the traveling microscope is noted. The microscope is moved across the
fringes using the horizontal traverse screw and the readings are taken when the vertical cross wire
coincides with every successive 5 fringes (5, 10, 15….). The width of every 15 fringes is calculated
and the width of one fringe is calculated. The mean of this gives the fringe width (β).
The cross wire is fixed at the inner edge of the rubber band and the reading from the
microscope is noted. Similarly reading from the microscope is noted keeping the cross wire at the
edge of the material. The difference between these two values gives the value of ‘l’. Substituting ‘β’
and ‘l’ in the given formula, the thickness of the given material can be determined.
WORK SHEET
CALCULATIONS:
28
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Result
29
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
VIVA – VOCE
7. Explain the reason for color formation in soap bubbles, when white light falls on it.
8. What happens to the fringe width, if the thickness of the material is increased?
30
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Aim
(i) To determine the velocity of Ultrasonic waves in the given liquid using Ultrasonic Interferometer.
(ii) To determine the compressibility of the given liquid.
Apparatus required
Ultrasonic Interferometer, measuring cell, frequency generator, given liquid, etc.
Formula
(i) Velocity of Ultrasonic waves in the given liquid v = nλ ms-1
2𝑑
Where, Wavelength 𝜆= metre (or) Å
𝑥
1
(ii)Compressibility of the given liquid 𝐾= m2 / N
𝜌𝑣 2
Explanation of symbols
32
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Theory
An Ultrasonic Interferometer is a simple and direct to determine the velocity of Ultrasonic waves in
33
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
liquid with a high degree of accuracy. Here the high frequency generator generates variable frequency,
which excited the Quartz Crystal placed at the bottom of the measuring cell (Fig. 12). The excited Quartz
Crystal generates Ultrasonic waves in the experimental liquid. The liquid will now serve as an acoustical
grating element. Hence when Ultrasonic waves passes through the rulings of grating, successive maxima
and minima occurs, satisfying the condition for diffraction.
Initial adjustments:
In high frequency generator two knobs are provided for initial adjustments. One is marked with ‘Adj’
(set) and the other with ‘Gain’ (Sensitivity). With knob marked ‘Adj’ the position of the needle on the
ammeter is adjusted and with the knob marked ‘Gain’, the sensitivity of the instrument can be increased for
greater deflection, if desired.
Procedure
The measuring cell is connected to the output terminal of the high frequency generator through a
shielded cable. The cell is filled with the experimental liquid before switching ON the generator is switched
ON, the Ultrasonic waves move normal form the Quartz Crystal till they are reflected back by the movable
reflector plate. Hence, standing waves are formed in the liquid in-between the reflector plate and the quartz
Crystal.
The distance between the reflector and crystal is varied using the micrometer screw such that the
anode current of the generator increases to a maximum and then decreases to a minimum and again
increases to a maximum in the anode current is equal to half the wave length of the Ultrasonic waves in the
liquid (Fig. 13.). Therefore, by nothing the initial and final position of the micrometer screw for one complete
oscillation (maxima – minima- maxima) the distance moved by the reflector can be determined.
To minimize the error, the distance (d) moved by the micrometer screw is noted for ‘x’
number of oscillations (successive maxima), by noting the initial and final reading in the micrometer screw
and is tabulated. From the total distance (d) moved by the micrometer screw and the number of
oscillations(x), the wavelength of ultrasonic waves can be determined using the formula λ = 2d/x. From the
value of λ and by noting the frequency of the generator (n), the velocity of the Ultrasonic waves can be
calculated using the given formula.
After determining the velocity of the Ultrasonic waves in liquids. The
compressibility of the liquid is calculated using the given formula.
34
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
35
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Result
VIVA – VOCE
9. What are the various liquids that can be used for finding the compressibility using Ultrasonic
interferometer?
10. What type crystal is thrown into vibrations in the case of Ultrasonic interferometer?
WORK SHEET
CALCULATIONS:
36
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
WORK SHEET
CALCULATIONS:
37
(i) To find the number of
lines per metre on the
grating (N)
Mean θ
= 2θ/2
N=
Mean θ
sin θ/nλ
VB
PHYSICS PRACTICAL MANUAL CUM RECORD
38
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
VB
VA
TR
Vernier B (VB)
VSC
MSR
TR
Vernier A (VA)
VSC
MSR
λ= 5893 A°
LC = 1´
Diffracted ray
Right (R2)
Left (R1)
readings
39
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Apparatus required
Spectrometer, plane transmission grating, mercury vapour lamp, sodium vapour lamp, spirit
level, lens, torch light etc.
Formula
(i) The number of lines drawn on the grating per meter is given by
𝑠𝑖𝑛 𝜃
𝑁= lines /meter
𝑛𝜆
Explanation of symbols
40
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Fig. 14. Position of the Grating Fig.15. Spectrometer Grating First to Get
Reflected Ray order Diffraction
Procedure
41
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Preliminary adjustments of the spectrometer are made. The grating (G) is mounted on the
grating table with its ruled surface facing the collimator. The slit is illuminated by a source of light
(either sodium (or) mercury vapour lamp) and is made to coincide with the vertical cross wire. (The
vernier scales are adjusted to read 0˚ and 180˚ for the direct ray. The telescope is rotated through
an angle 90˚ and is fixed. The grating table is adjusted until the image coincides with the vertical
cross wire. Both the grating table and the telescope are fixed at this position (fig.14). Now rotate
the vernier tables through 45˚in the same direction in which the telescope has been previously
rotated. The light from the collimator incidents normally (perpendicularly) on the grating. The
telescope is released and is brought on line with the direct image of the slit. Now the grating is said
to be in the normal incidence position (fig. 15).
(ii) Standardization of grating (To find the number of lines drawn in the grating per
meter)
The slit is illuminated by sodium vapour lamp. The telescope is released to get the diffracted
image of the first order on the left side of the central direct image. The readings are tabulated from
the two verniers VA and VB. Similarly readings are taken for the right side of the central direct
image (fig. 15). The difference between the two readings gives 2θ, where θ is the angle of first
order diffraction. The number of lines per meter (N) of the grating is calculated using the given
formula. The experiment is repeated for the second order and the readings are tabulated.
The sodium vapour lamp is replaced by mercury vapour lamp. The diffracted images of the first
order are seen on either side of the central direct image (fig.15). As before the readings are
tabulated by coinciding the vertical cross wire with the prominent lines namely violet, blue, blueish
green, green, yellow, red of the mercury spectrum. The difference between the readings give 2θ,
from this θ can be found. The wavelength of each spectral line is calculated using the given
formula.
42
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
43
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Result
(i) Number of lines drawn in the grating per meter = ………….. Lines/ meter.
λV = ……….…………. Aº λB = ……….…………. Aº
λY = ……….…………. Aº λR = ……….…………. Aº
VIVA - VOCE
WORK SHEET
CALCULATIONS:
44
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
WORK SHEET
CALCULATIONS:
45
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
46
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
1 θ2+5
2 θ2+4
3 θ2+3
4 θ 2+ 2
5 θ2 + 1
6 θ2
7 θ 2- 1
8 θ2-2
9 θ2-3
10 θ2-4
11 θ2-5
47
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Apparatus required
Lee’s disc apparatus, two thermometers, bad conductor, stop watch, steam boiler, vernier
caliper, screw gauge, biscuit balance etc.
Formula
𝑑𝜃
𝑀𝑆( ) 𝑥(𝑟+2ℎ)
𝑑𝑡 𝜃 2
Thermal conductivity of the given band conductor 𝐾 =
𝜋𝑟 2 (𝜃1 −𝜃2 ) 2(𝑟+ℎ)
Explanation of symbols
48
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
LC = 0.01 cm ZE = ………….
ZC = …………. x 10-2m
Main Scale
Vernier Scale Observed Reading Correct Reading
S.No. Reading
Coincidence (VSC) OR=MSR+(VSCXLC) CR = OR±ZC
(MSR)
Description
49
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Lee’s disc apparatus consists of a brass metal disc (B) suspended horizontally by three
strings form a stand. A hollow steam chamber (A) with inlet and outlet for steam is placed above.
The given bad conductor is placed between them. Two thermometers T1 & T2 are inserted to
measure the temperatures of A and B respectively.
Procedure
The experimental arrangement is as shown in fig 16. Steam is allowed to pass through the
steam chamber. The temperature indicated by two thermometers start rising. After 30 minutes a
steady state is reached (i.e) the temperature of the lower disc will no longer rises. At this stage,
steady temperatures θ1 and θ2 are recorded from the thermometers T1 and T2.
Now the cardboard is removed and the lower disc is heated directly by keeping it in contact
with the steam chamber. When the temperature of the lower disc attains a value of about 10°C
more than its steady state temperature, the chamber is removed and the lower disc is allowed to
cool down on its own accord.
When the temperature of the disc reaches 5°C above the steady temperature (θ2) of the disc
i.e., (θ2+5°C), a stop watch is started and the time is noted for every 1°C fall of temperature until
the metallic disc attains temperature (θ2-5°C).
The thickness and radius of the metallic disc is found using screw gauge and vernier caliper
respectively. The thickness of the bad conductor is found using screw gauge. The mass of the
metallic disc is found by using biscuit balance. The readings are tabulated in the tabular column.
Graph
A graph is drawn by taking time along the x-axis and the temperature along y-axis (fig. 17)
Cooling curve is drawn. From the cooling curve dθ/dt is calculated by drawing a triangle by
taking 0.5°C above and 0.5°C below the steady temperature θ 2. Substituting this dθ/dt in the
given formula, thermal conductivity of the card board can be calculated.
50
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Result
51
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
VIVA - VOCE
6. What is the use of cooling the slab and noting the time?
7. What happen to the thermal conductivity if the thickness of the given bad conductor is
increased?
8. Is the diameter of the bad conductor should match diameter of the disc (D) and the steam
chamber (S)? Why?
9. Will there be any change in thermal conductivity if the area of cross section of bad conductor
is decreased: Justify.
WORK SHEET
CALCULATIONS:
52
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
WORK SHEET
CALCULATIONS:
53
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
54
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Fig 18 a. Top view of the B-H Curve Unit
Apparatus required
CRO, B-H curve unit, patch cords
55
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Formula
𝑵 𝑹𝟐 𝑪𝟐
Energy loss = 𝑵𝟏 × × × 𝑺𝑽 × 𝑺𝑯 × 𝑨𝒓𝒆𝒂 𝒐𝒇 𝒕𝒉𝒆 𝒍𝒐𝒐𝒑
𝟐 𝑹𝟏 𝑨𝟐
Explanation of symbols
DESCRIPTION
The experimental arrangement is shown in the figure 18a. One of the specimens
used in the unit is made using transformer stampings. There are two windings on the specimen
(primary and secondary). The primary is fed to low A.C voltage (50Hz). This produces a magnetic
field H in the specimen. The voltage across R1 (resistance connected in series with primary) is
proportional to the magnetic field. It is given to the imput of the CRO. The A.C magnetic field
induces a voltage in the secondary coil. The voltage induced is proportional to dB/dt. This voltage
is applied to passive integrating circuit. The output of the integrator is proportional to B and fed to
the vertical input of the CRO. As a result of the application of voltage proportional to H the
horizontal axis and a voltage proportional to B is the vertical axis, the loop is formed as shown in fig
18b.
56
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
10
Observations
Calculation
PROCEDURE
The unit one to force the B-H loop (hysteresis) of a ferromagnetic specimen using a CRO is
shown in figure. A measurement of the area of the loop leads to the evaluation of the energy loss in
the specimen. The top view of the unit is shown in the figure. There are 12 terminals on the panel;
sin patch cords are supplied with the kit.
The value of R1 can be selected connecting terminal D to B or C (A-D = 50 ohm; B-D = 150
ohm; C-D = 50 ohm)
57
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
The terminal marked GND is connected to the ground of the CRO. The H is connected to
the Horizontal input to the ground of the CRO. The H is connected to the Horizontal input of the
CRO. The terminals V are switched on. The hysteresis loop is formal. The horizontal and vertical
gains are adjusted such that the loop occupies maximum area of the screen of the CRO. Once this
adjustment is made, the gain controls should not be disturbed. The loop is traced on a translucent
graph paper. The area of the loop is estimated.
The connections from CRO are removed without disturbing the horizontal and vertical gain
controls. The vertical sensitivity of the CRO is determined by applying a known A.C voltage say 1
volt (peak to peak).
If the spot deflects by X cms for 1 volt, the vertical sensitivity is 1/X x 10-2 (volt/m). Let it be
dV. The horizontal sensibility of CRO is determined by applying a known A.C. voltage say 1 volt
(peak to peak). Let the horizontal sensitivity be SH (volt/m).
The transformer core may be replaced by ferrite ring and hysteresis loss in ferrite core can
be found.
WORK SHEET
CALCULATIONS:
58
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Result:
59
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
1 W
60
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
2 W+50
3 W+100
4 W+150
5 W+200
6 W+250
Apparatus requited
A long uniform beam usually a meter scale, travelling microscope, pin, weight hanger
with slotted weights, vernier calipers, Screw gauge, knife edges etc.,
Formula
The Young’s Modulus of the given material of the beam
𝑔𝑙 3 𝑀
By Calculation method 𝑌= . Nm-2
4𝑏𝑑 3 𝑦
𝑔𝑙 3 1
By Graphical method 𝑌= . Nm-2
4𝑏𝑑 3 𝐾
Explanation of symbols
61
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
M Load applied Kg
X (M)
Y ( h)
To find the thickness (d) of the beam using screw gauge. LC = 0.01 mm
ZE = …………. ZC = …………. x 10-3m
62
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Unit X 10-3m Div. X 10-3m X 10-3m
Procedure
The given beam is placed on the two knife edges (A and B) at a distance say 70 cm or 80
cm. A weight hanger is suspended at the centre(C) of the beam and a pin is fixed vertically on the
frame of the hanger as shown in fig.19. Taking the weight hanger alone as the dead load the tip o
the pin is focused by the microscope, and is adjusted in such a way that the tip of the pin just
touches the horizontal cross wire. The reading on the vertical scale is noted. Now the weight is
added in steps of 50 grams. Each time the tip of the pin is made to touch the horizontal cross
wire and the readings are noted from the vertical scale of the microscope. The procedure is
followed until the maximum load is reached. The same procedure is repeated by unloading the
weight in steps of same 50 grams and the readings are tabulated in the tabular column. From the
readings the mean of (M/y) is calculated. The thickness and the breadth of the beam are
measured using screw gauge and vernier calipers respectively and are tabulated. By substituting
the values in the given formula. The young’s modulus of the material of the beam can be
calculated. Graph
A Graph is drawn taking load (M) along x
axis and depression ‘y’ along y axis as shown in figure. The slope of the graph gives the value K
= y/M. Substituting the value of the slope in the given formula, the Young’s modulus can be
calculated.
Result
The Young’s modulus of the given material of the beam
by calculation Y = …………………. Nm-2
by Graph Y = …………….…… Nm-2
VIVA - VOCE
1. What is meant by non – uniform bending?
2. Define neutral axis.
3. Name any two methods used to determine the young’s modulus of the beam.
4. Define elasticity.
63
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
5. Will there be any change in young’s modulus of the material, if its thickness is increased?
Justify.
6. What are the basic assumptions made from the theory of bending?
7. Why iron girders used in buildings are made in the form of I section?
8. What is the use of keeping an optimum of 0.7 to 0.8 meter distance between the knife
edges?
9. Define elastic limit.
10. What is meant by elastic constants?
WORK SHEET
CALCULATIONS:
64
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
WORK SHEET
CALCULATIONS:
65
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
66
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Apparatus required
Point contact diode, heating arrangement to heat the diode, ammeter, voltmeter,
thermometer etc.
Formula
Band Gap Energy Eg = 0.198 x Slope eV
∆ 𝑙𝑜𝑔 𝐼𝑠
Where 𝑆𝑙𝑜𝑝𝑒 = 1000
∆( )
𝑇
Explanation of symbols
67
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Is Saturation Current µA
Theory
For a semiconductor diode at 0 K the valence band is completely filled and the conduction
band is completely filled and the conduction band is empty and it behaves as an insulator. If the
temperature is increased, some of the valence electrons gains thermal energy greater than the
forbidden band gap energy (Eg) and it moves to conduction band, which constitutes some current
to flow through the semiconductor diode.
Temperature in Temperature in
S.No. 1000/T Is Log Is
centigrade Kelvin
Unit °C K K-1 X 10-6 Amp Amp
1
2
3
4
5
6
7
8
9
10
11
12
13
68
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
14
15
16
17
18
19
20
Eg = 0.198 x Slope eV
Eg = ……………… eV
Procedure
The circuit is given as shown in fig.20. The point contact diode and the thermometer are
immersed in a water (or) oil bath, in such a way that the thermometer is kept nearby the diode.
The power supply is kept constant (say 3 volts). The heating mantle is switched ON and the oil
bath is heated up to 70°C. Now the heating mantle is switched OFF and the oil bath is allowed to
cool slowly. For every one degree fall of temperature the microammeter reading (I s) is noted.
A graph is plotted taking 1000/T along X axis and log I s along negative Y axis, (Since Is is in
the order of micro-amperes, log Is value will come in negative). A straight line is obtained as
shown in model graph (fig.21). By finding the slope of the straight line, the band gap energy can
be calculated using the given formula. The same procedure can be repeated for various constant
power supplies (4volts, 5 volts)
Result
VIVA - VOCE
69
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
7. What is the principle used in finding the band gap energy of a semiconductor?
8. What is the use of keeping the diode inside the oil bath?
9. Shall the oil bath be replaced by water bath? State the reason.
10. What is the biasing of the semiconductor diode in the band gap experiment?
WORK SHEET
CALCULATIONS:
70
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
WORK SHEET
CALCULATIONS:
71
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Circuit diagram
72
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Apparatus requited
Bridge wire resistance coil, Battery, 4 & 2 dial resistance boxes, copper strips,
galvanometer, High resistance, key, Jockey, etc.,
Formula
Explanation of symbols
73
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Table No: 1
74
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
10
Mean =……………..
Procedure
Carey Foster’s bridge is more useful for comparing two nearly equal resistances or to
determine unknown resistance. It is the modified form of the meter bridge and works on the
principle of Wheatstone’s bridge.
Since the end resistances are eliminated, the unknown resistances can be determined very
accurately.
It consists of a uniform resistance wire AB, of one meter long. Normally the wire is made
from managing which has zero temperature coefficient of resistance. The ends of the wire are
soldered to two thick L-Shaped cooper strips of negligible resistance. There are three more
copper strips which are fixed on the wooden board between the first two L-shaped strips so as to
form four gaps 1, 2, 3 and as shown in fig22(a). The copper strips are provided with binding
screws for electrical connection. Two known equal standard resistances P & Q are connected in
gaps 2 and 3 respectively and a variable resistance box R and the given unknown resistance S
are connected in gaps 1 and 4 respectively. Battery with a key and a galvanometer with a safety
high resistance and jockey are connected as shown in fig 22a. Contact can be made at any point
on the bridge wire by means of jockey. A meter scale is fixed on the board parallel to the length
of the wire so as to take readings directly.
Experiment to determine the resistance of the given coil of wire:
Having introduced a value R in the resistance box, the circuit is closed and the
balancing point J on the bridge wire where there is no deflection in the galvanometer is
determined. The balancing length l1 is measured from the point ‘A’. The experiment is repeated
by interchanging R and S and the balancing length l2 is noted. The experiment is repeated by
75
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
varying the known resistance R and in each case l1 and l2 are measured.
Determination of :
To determine the resistance per unit length of the bridge wire, the
resistance S is replaced by a thick copper strip (i.e. S = 0) and the balancing length ‘l 1’ is
determined using fractional resistance in R.
Now by interchanging R and copper strip (S = 0, the
balancing length l2’ is determined.
0 = R+ (l1’-l2’)
Table: 2
Resistance ‘R’
S.No.
ohm l1 m l2m Ohm
76
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
10
Now the unknown resistance is inserted in the bridge circuit instead of copper stip. The bridge
will have the maximum sensitivity when S = R and hence the error in measuring the value of S is
also minimum in that condition. So, after inserting the unknown resistance in the bridge arm, the
jockey is pressed at the 50th cm of the bridge wire and the value of R is varied. The value of R at
which there is null deflecting in the galvanometer is noted. This will give the approximate resistance
of the unknown resistance. Let it be X ohm. Now, the value of R is varied is steps of 0.2 ohm
between (X+1) ohm to (X-1) ohm and correspondingly the balancing lengths l1 and l2 are
determined and tabulated in the table no 2.
Mean of the last column in the tabular column number 1
indicated the resistance of the bridge wire per unit length (p) and that value is substituted in
equation in the tabular column number 2. The mean of the last column in the tabular column
number 2 gives the value of the unknown resistance of the given coil of wire.
Special cases:
Result
1. Resistance per unit length of the bridge wire = …………………. Ohm / Meter
2. Specific resistance of resistivity of the material of the coil = ………….. Ohm - Meter
77
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
VIVA - VOCE
WORK SHEET
CALCULATIONS:
78
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
WORK SHEET
CALCULATIONS:
79
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Time Height
Height Pressure
note Time for of
Burette of final head
S.No. while Range flow of 5 initial ht
reading reading h=(h1+h2/2)-
crossing cc liquid reading
h2 h0
level h1
X10- X10-
Unit cc Seconds 2m seconds X10-2m X10-2m X10-2m 2m
1 0 0-5
2 5 5-10
3 10 10-15
4 15 15-20
5 20 20-25
6 25 25-30
7 30 30-35
8 35 35-40
9 40 40-45
80
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
10 45 45-50
11 50 -
Mean ht = ………… X10-2m -sec
Apparatus required
A graduated burette, rubber tube, capillary tube, pinch cork, etc.,
Formula
𝜋𝜌𝑔𝑟 4 ℎ𝑡
Coefficient of viscosity 𝜂 = ( 𝑣 ) (Nsm-2)
8𝑙
Explanation of symbols
ℎ1 − ℎ2
h − ℎ0 metre
2
81
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Right
V2
Top r = H1~H2
H1
Bottom
H2
82
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Procedure
The burette is held vertically on a retort stand. A capillary tube is attached to the lower end
of the burette using a rubber tube as shown in fig 23. The burette is filled with the given liquid. The
capillary tube is made horizontal and the liquid is allowed to flow freely through it. When the liquid
comes to a known height (h1), which is the height measured from the axis of the capillary tube, the
stop watch is started. The stop watch is stopped when the liquid comes to another level which is of
ℎ1 − ℎ2
height h2 from the axis of the capillary tube. Then the driving height is given by − ℎ0 . The
2
driving height, volume of the liquid and the time taken for flow of liquid are noted in the tabular
column.
The experiment is repeated for various known heights of the liquid and the time taken is
noted. The mean of (ht/V) is taken. The radius of the bore of the capillary tube figure. Can be
found by using a travelling microscope by mounting the capillary tube over a stand. Substituting the
above data in the given formula, the coefficient of viscosity can be calculated.
Result:
VIVA – VOCE
3. What will happen to the viscosity if the density of the liquid is increased?
6. What will happen to the viscosity of the liquid if the temperature of the liquid is increased?
Justify your answer.
WORK SHEET
CALCULATIONS:
83
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
WORK SHEET
CALCULATIONS:
84
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
85
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Face –I
(Left) (R1) (R1)
Face – 2
(Right) (R2) (R2)
Mean A =
86
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Apparatus required
Spectrometer, glass prism, sodium vapour lamp, transformer, mercury vapour lamp, pencil
torch, lens, spirit level etc.,
Formula
(𝐴+𝐷)
𝑠𝑖𝑛[ ]
2
Refractive index of the given prism is given by 𝜇 = 𝐴 (No unit)
𝑠𝑖𝑛[ ]
2
𝜇1 −𝜇2
Dispersive power of the prism in the wavelength region of λ1 and λ2 is = 𝜇1 +𝜇2 (No unit)
[ ]−1
2
Explanation of symbols
Symbo
Explanation Unit
l
A Angle of the prism degrees
87
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
88
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Procedure
To find the angle of Prism (A)
To initial adjustments of the spectrometer is made. The silt is illuminated by yellow light from
the sodium vapour lamp. The given prism is mounted on the prism table such that light emerging
from the collimator should be made to incident on both the refracting faces of the prism as shown
in fig 25.
The telescope is rotated (left or right) to catch the image of the slit reflected by one of
the refracting face of the prism. The telescope is fixed. By adjusting the tangential screw, the image
is made to coincide with the vertical cross wire. The main scale and the vernier scale readings are
noted from both the vernier A (VA) and vernier B (VB). Similarly readings are taken for the image
reflected by other refracting face of the prism. The difference between the two readings gives 2A,
where ‘A’ is the angle of prism.
(ii)To find the angle of minimum deviation (D) and refractive index (µ)
LC = 1’ TR = MSR+ (VSCXLC)
Angle of Prism (A) = …………………..
89
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Direct
Ray (R1) (R1)
Violet – I
(R2) (R2)
Violet - II
(R2) (R2)
Blue
(R2) (R2)
Blueish
Green (R2) (R2)
Green
(R2) (R2)
Yellow –
I (R2) (R2)
Yellow -
II (R2) (R2)
Red
(R2) (R2)
Result:
90
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
VIVA – VOCE
3. What are the initial adjustments to be made before using the spectrometer?
WORK SHEET
CALCULATIONS:
91
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
WORK SHEET
CALCULATIONS:
92
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
93
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
TR = MSR + (VSCXLC)
Apparatus required
A long uniform beam usually a meter scale, travelling microscope, pin, weight hanger
with slotted weights (2 sets), vernier calipers, Screw gauge, knife edges etc.,
Formula
The Young’s Modulus of the given material of the beam
94
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
3𝑀𝑔𝑙 2 𝑎
By Calculation method 𝐸= Nm-2
2𝑏𝑑 3 ℎ
3𝑔𝑙 2 𝑎 1
By Graphical method 𝐸= . Nm-2
2𝑏𝑑 3 𝐾
Explanation of symbols
M Load applied Kg
X (M)
Y ( h)
(i) To find Breadth (b) of the beam using vernier calipers ZE = ………….
LC = 0.01 cm ZC = …………. x 10-2m
95
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
1
To find the thickness (d) of the beam using screw gauge. ZE = ………….
LC = 0.01 mm ZC = …………. x 10-3m
Procedure
The given beam is supported on the two knife edges (A and B) in the same horizontal level, equal
lengths projecting beyond each knife- edge. The weight hanger are attached at two points equally distant
(a) beyond the knife-edges. A pin is fixed exactly at the mid-point of the beam. A travelling microscope
capable of vertical motion is arranged in front of the pin and focused on its tip. The tip is made to coincide
with the horizontal cross-wire.
Loads are added to both the hangers in steps of M (50 gms) and the microscope is moved up so that
the tip of the image of the pin just coincides with the horizontal cross-wire in each case and the MSR, VSC
readings are noted.
The same procedure is repeated by unloading the weight in steps of same 50 grams and the
readings are tabulated in the tabular column. From the readings the mean of (M/h) is calculated. The
thickness and the breadth of the beam are measured using screw gauge and vernier calipers respectively
and are tabulated. By substituting the values in the given formula the Young’s modulus of the material of
the beam can be calculated.
Graph
A graph is drawn taking load (M) along x axis and elevation h along y
axis as shown in figure. The slope of the graph gives the value K=h/M. Substituting the values of
the slope in the given formula, the Young’s modulus can be calculated.
96
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
Result
The Young’s modulus of the given material of the beam
By calculation Y = …………………. Nm-2
By Graph Y = …………….…… Nm-2
VIVA - VOCE
1. What is meant by uniform bending?
2. Define neutral axis.
3. Name any two methods used to determine the young’s modulus of the beam.
4. Define elasticity.
5. Will there be any change in young’s modulus of the material, if its thickness is increased?
Justify.
6. What are the basic assumptions made from the theory of bending?
7. Why iron girders used in buildings are made in the form of I section?
8. What is the use of keeping an optimum of 0.7 to 0.8 meter distance between the knife
edges?
9. Define elastic limit.
10. What is meant by elastic constants?
WORK SHEET
CALCULATIONS:
97
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
WORK SHEET
CALCULATIONS:
98
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
99
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Mean L/T2=………..…ms-2
Apparatus required
Circular metal disc, suspended wire, biscuit balance, metre scale, stop watch, screw gauge,
vernier caliper, etc.,
Formula
𝑀𝑅 2
Moment of inertia of the disc 𝐼= Kg m2
2
8𝜋𝐼𝐿
Rigidity modulus of the material of the given wire 𝑛 = Nm-2
𝑟4 𝑇2
Explanation of symbols
100
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
(iii)To find the diameter of the suspension wire using screw gauge. ZE = ………….
LC = 0.01 mm ZC = …………. x 10-3m
101
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
1
Theory
The circular disc is rotated in a horizontal plane so that a twist is given to the wire which
holds the disc. Hence the various elements of the wire undergo shearing strains. The restoring
couples, which tend to restore the unstrained conditions, are called into action. Now when the
disc is released it starts executing torsional oscillations. The couple which acts on the disc
produces in it an angular acceleration which is proportional to the angular displacement and is
always directed towards its mean position. Hence the motion of the disc is a simple harmonic
motion. Procedure
A uniform thin wire whose rigidity modulus has to be found is
suspended from a rigid support. The other end of the wire is attached to a circular disc using an
adjustable chuck. The length of the suspension wire (L) between the point of suspension and the
metal disc is the length of the torsional pendulum as shown in fig 28.
Initially, the length of the pendulum is adjusted; say 50 cm.
Torsional oscillations are set up by giving a small twist to the disc. The time taken for 10
oscillations are found and hence time period, which is nothing but the time taken of 5 cm and
periods of oscillations are found for each length. The readings are tabulated in the tabular column
and the mean of L/T2 is calculated. The radius of the wire (r) is found using
screw gauge and the radius of the disc (R) is found using vernier calipers. The mass (M) of the
metal disc is found using the biscuit balance. Substituting the values, in the given formula the
moment of inertia can be calculated. Now by substituting the value of moment of
inertia and L/T2 in the given formula rigidity modulus of the given wire can be calculated.
Graph
The value of L/T2 can also be found by drawing a graph taking ‘L’ along x-axis and T2 along
y-axis as shown in figure. The slope of the graph will give the value of L/T 2. Substituting the
graphical value of L/T2 in the given formula, the rigidity modulus can be determined by graphical
method.
102
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
WORK SHEET
CALCULATIONS:
103
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Result
VIVA - VOCE
6. If the radius of the disc is altered, what will happened to the rigidity modulus of the wire.
Explain.
7. What is the use of varying the length of suspension while doing the experiment?
8. Why the disc is circular? Are there any other shapes possible to find the moment of inertia?
104
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
10. Will the moment of inertia of the disc vary with the material of the wire? If so explain.
STANDARD VALUES
Symbol for
Base quantity Symbol Description SI unit
dimension
Length l The one dimensional extent of an object. metre (m) L
Mass m The amount of matter in an object. kilogram (kg) M
Time t The duration of an event. second (s) T
Electric current I Rate of flow of electrical charge. ampere (A) I
Temperature T Average energy per degree of freedom of a system. kelvin (K) Θ
Amount of
n Number of particles compared to the number of atoms in 0.012 kg of 12C. mole (mol) N
substance
Luminous
L Amount of energy emitted by a light source in a particular direction. candela (cd) J
intensity
Plane angle θ Measure of a change in direction or orientation. radian (rad) 1
Solid angle Ω Measure of the size of an object as projected on a sphere. steradian (sr) 1
Sym
Derived quantity Description SI units Dimension
bol
Acceleration a Rate of change of the speed or velocity of an object. m s−2 L T−2
−2
Angular acceleration α Rate of change in angular speed or velocity. rad s T−2
Angular speed (or ω or
The angle incremented in a plane by a segment connecting an object and a reference point. rad s−1 T−1
angular velocity) ω
Angular momentum L Measure of the extent and direction and object rotates about a reference point. kg m2 s−1 M L2 T−1
Area A The two dimensional extent of an object. m2 L2
Area density ρA The amount of mass per unit area of a two dimensional object. kg m−2 M L−2
farad (F = A2 s4
Capacitance C Measure for the amount of stored charge for a given potential. I2 T4 M−1 L−2
kg−1 m−2)
katal (kat = mol
Catalytic activity Change in reaction rate due to presence of a catalyst. N T−1
s−1)
Catalytic activity
Change in reaction rate due to presence of a catalyst per unit volume of the system. kat m−3 N L−3 T−1
concentration
Chemical potential μ The amount of energy needed to add a particle to a system. J mol−1 M L2 T−2 N−1
Molar concentration C Amount of substance per unit volume. mol m−3 N L−3
Current density J Amount of electric current flowing through a surface. A m−2 I L−2
2
Measure for the received amount of radiation adjusted for the effect of different types of sievert (Sv = m
Dose equivalent H L2 T−2
radiant on biological tissue. s−2)
Dynamic Viscosity η Measure for the resistance of an incompressible fluid to stress. Pa s M L−1 T−1
coulomb (C = A
Electric Charge Q Amount of electric charge. IT
s)
Electric charge density ρQ Amount of electric charge per unit volume. C m−3 I T L−3
Electric displacement D Strength of the electric displacement. C m−2 I T L−2
Electric field strength E Strength of the electric field. V m−1 M I−1 L2 T−3
siemens (S = A2
Electrical conductance G Meausure for how easily current flows through a material. L−2 M−1 T3 I2
s3 kg−1 m−2)
volt (V = kg m2
Electric potential V The amount of work required to bring a unit charge into an electric field from infinity. L2 M T−3 I−1
A−1 s−3)
Electrical resistance R The degree to which an object opposes the passage of an electric current. ohm (Ω = kg m2 L2 M T−3 I−2
105
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
A−2 s−3)
joule (J = kg m2
Energy E The capacity of a body or system to do work. M L2 T−2
s−2)
Energy density ρE Amount of energy per unit volume. J m−3 M L−1 T−2
Entropy S Measure for the amount of available states for a system. J K−1 M L2 T−2 Θ−1
newton (N = kg
Force F The external cause of acceleration, acting on an object. M L T−2
m s−2)
Frequency f The number of times something happens in a period of time. hertz (Hz =s−1) T−1
Half-life t1/2 The time needed for a quantity to decay to half its original value. s T
Heat Q Amount of energy transferred between systems due to temperature difference. J M L2 T−2
Heat capacity Cp Amount of energy needed to raise the temperature of a system by one degree. J K−1 M L2 T−2 Θ−1
Heat flux density ϕQ Amount of heat flowing through a surface per unit area. W m−2 M T−3
lux (lx = cd sr
Illuminance Ev Total luminous flux incident to a surface per unit area. J L−2
m−2)
ohm (Ω = kg m2
Impedance Z Measure for the resistance of an electrical circuit against an alternating current. L2 M T−3 I−2
A−2 s−3)
Index of refraction n The factor by which the speed of light is reduce in a medium. 1
Measure for the amount of magnetic flux generated for a certain current run through a henry (H = kg
Inductance L M L2 T−2 I−2
circuit. m2 A−2 s−2)
Irradiance E Power of electromagnetic radiation flowing through a surface per unit area. W m−2 M T−2
Linear density ρl Amount of mass per unit length of a one dimensional object. M L−1
Luminous flux (or lumen (lm = cd
F Perceived power of a light source. J
luminous power) sr)
Magnetic field strength H Strength of a magnetic field in a material. A m−1 I L−1
Measure of quantity of magnetism, taking account of the strength and the extent of a weber (Wb = kg
Magnetic flux Φ M L2 T−2 I−1
magnetic field. m2 A−1 s−2)
tesla (T = kg
Magnetic flux density B Measure for the strength of the magnetic field. M T−2 I−1
A−1 s−2)
Magnetization M Amount of magnetic moment per unit volume. A m−1 I L−1
Mass fraction x Mass of a substance as a fraction of the total mass. kg/kg 1
(Mass) Density (volume
ρ The amount of mass per unit volume of a three dimensional object. kg m−3 M L−3
density)
Mean lifetime τ Average time needed for a particle to decay. s T
−1
Molar energy Amount of energy present is a system per unit amount of substance. J mol M L T−2 N−1
2
M L2 T−2 Θ−1
Molar entropy Amount of entropy present in a system per unit amount of substance. J K−1 mol−1
N−1
Molar heat capacity c Heat capacity of a material per unit amount of substance. J K−1 mol−1 M L2 T−2 N−1
Moment of inertia I Inertia of an object with respect to angular acceleration. kg m2 M L2
Momentum p Product of an object's mass and velocity. Ns M L T−1
Measure for how the magnetization of material is affected by the application of an external
Permeability μ H m−1 M L−1 I−2
magnetic field.
Measure for how the polarization of a material is affected by the application of an external
Permittivity ε F m−1 I2 M−1 L−2 T4
electric field.
Power P The rate of change in energy over time. watt (W) M L2 T−3
pascal (Pa = kg
Pressure p Amount of force per unit area. M L−1 T−2
m−1 s−2)
becquerel (Bq =
(Radioactive) Activity A Number of particles decaying per unit time. T−1
s−1)
106
PHYSICS PRACTICAL MANUAL CUM RECORD I & II Sem
SI Unit Prefixes
Factors Prefix Symbol Factors Prefix Symbol Factors Prefix Symbol Factors Prefix Symbol Factors Prefix Symbol
1012 tera T 103 kilo k 10-1 deci d 10-6 micro µ 10-15 femto f
10 9
giga G 10 2
hecto h 10 -2
centi c 10 -9
nano n 10-18 atto a
106 mega M 101 deca da 10-3 milli m 10-12 pico p 10-15 femto f
PHYSICAL STANDARD
S.NO. SUBSTANCE UNIT
CONSTANT VALUE
Water 1000
Kerosene 830
Castor oil 970
Glycerine 1260
1 Density Copper 8900 Kgm3
Brass 8600
Steel 7800
Aluminium 2700
Iron 7500
Aluminium 2.5 x 1010
Brass 3.5 x 1010
Cast Iron 5.0 x 1010
Rigidity
2 3.4 to 3.6 x Nm-2
Modulus Copper
1010
Wrought Iron 8.0 x 1010
Steel (Cast) 7.6 x 1010
107
PHYSICS PRACTICAL MANUAL CUM RECORD 2010-2011
Steel (Mild) 8.9 x 1010
Brass 0.001 to 0.002
Copper 0.0039
PHYSICAL STANDARD
S.NO. SUBSTANCE UNIT
CONSTANT VALUE
Box wood 1 x 1010
Teak wood 1.7 x 1010
Aluminium 7.1 x 1010
Youngs Brass 9.8x 1010
3 Nm-2
Modulus Cast Iron 10 to 12 x 1010
Copper 11.7 x 1010
Wrought Iron and steel 20x 1010
Glass 6 x 1010
Coefficient of Water 0.0008
Viscosity (at Kerosene 0.002
4 Nsm-2
room Coconut oil 0.0154
temperature) Glycerine 0.3094
Card board(varies with specimen also) 0.04
Thermal Ebonite 0.7
5 Wm-1K-1
Conductivity Glass 1
Wood & Rubber 0.15
Crown Glass 1.5
Flint Glass 1.56
6 Refractive Index Dense Crown Glass 1.62 (No Unit)
Dense Flint Glass 1.65
Water 1.333
Sodium Vapour Lamp 5893
Mercury Vapour Lamp
Red 6234
Yellow I 5791
Standard Yellow II 5770
7 A°
Wavelength Green 5461
Blueish Green 4916
Blue 4358
Violet I 4078
Violet II 4047
Temperature Aluminium 0.0043
8 Co-efficient of Brass 0.001 to 0.002 per °C
resistance Copper 0.0039
108