DC54D Z

Galvanized Steel Sheets
Galvanized steel sheets

Galvanized steel sheet, also called zinc coated steel sheet, owns many merits like strong coating
adhesiveness, high erosion-resistance, accurately controlled zinc coating thickness, high size
precision, flat profile and good mechanical, processing and welding performance. Therefore, the
galvanized steel sheet is not best sale in the international market but favored by the customers.
Category of Hot-dip galvanized products: commercial purpose, drawing, deep drawing, extra
deep drawing, supreme extra deep drawing, structure, and cold forming.
The products of these lines are widely used in electrical household appliance, architecture,
transportation, furniture, auto parts etc.
1. Applications and features are given as following table

Steel Grade Application Feature
DC51D+Z (St01Z, St02Z, St03Z) ,
Commercial purpose Low carbon and/or ultra-low
DC51D+ZF
carbon steel
DC52D+Z (St04Z), DC52D+ZF Drawing
DC53D+Z (St05Z), DC53D+ZF Deep drawing
DC54D+Z (St06Z), DC54D+ZF
Extra deep drawing
DD54D+Z (St06ZR) Ultra-low carbon steel
Supreme extra deep
DC56D+Z (St07Z), DC56D+ZF
drawing
2. Available sizes: Nominal thickness: 0.30mm~3.0mm, nominal width: 800mm~1830mm Note:
nominal thickness of a plate/strip is sum of base plate thickness and coating thickness.
3. Chemical Composition %:
CHEMICAL
bse metal type Grade COMPOSITION %
C Si Mn P
DC51D+Z (St01Z, St02Z, St03Z) ,
≤0.10 - ≤0.50 ≤0.035
DC51D+ZF
cold rolled steel
DC52D+Z (St04Z), DC52D+ZF ≤0.08 - ≤0.45 ≤0.030
sheet
DC53D+Z (St05Z), DC53D+ZF ≤0.08 - ≤0.40 ≤0.030
DC54D+Z (St06Z), DC54D+ZF ≤0.01 ≤0.10 ≤0.30 ≤0.025
Add: Suite F,8/F Jinhao Business Bld., Renmin Road, Anyang, Henan, China
Tel: (86) 372 5065802 Fax: (86) 372 5065803
DC56D+Z (St07Z), DC56D+ZF ≤0.01 ≤0.10 ≤0.30 ≤0.025

DD51D+Z (St01ZR, St02ZR) ≤0.10 - ≤0.50 ≤0.035
hot rolled steel sheet
DD54D+Z (St06ZR) ≤0.01 ≤0.10 ≤0.30 ≤0.025
4. Mechanical performances and coating adhesiveness

Mechanical performances Coating Adhesiveness
After Breakage Percent
Elongation Bending Center Diameter in Following
(LO=80mm,b=20mm)% Coating Weight (g/m2)c (a=plate
Yield Tensile
Grade ≥ thickness)
Strength Strength
L0=80mm,b=20mm
MP MP ≥
Under following nominal
thickness mm ≤140/140 >140/140~175/175 >175/175
≤0.7 >0.7
DC51D+Z
(St01Z,
St02Z, - 270~500 20 22
St03Z) ,
DC51D+ZF
DC52D+Z
(St04Z), 140~300 270~420 24 26
DC52D+ZF
DC53D+Z 0a 1a 2a
(St05Z), 140~260 270~380 28 30
DC53D+ZF
DC54D+Z
34 36
(St06Z) 140~220 270~350
DC54D+ZF 32 34
DC56D+Z
38 40
(St07Z) 120~180 270~350
DC56D+ZF 36 38
5. Coating weight range

Weight Range of Following Coatings a g/m2
Applicable Surface
coating form (A/B)
Structure
Zinc Coating Zn-Fe Alloy Coati
equally coating Z,X,G,GX,N,R 40/40~225/225 30/30~90/90
differential
N,R 30~150 (each side) -
coating
a. 50 g/m2coating weight is equivalent to about 7.1μm. b. max. differential coating thickness ratio
is 1:3.
6. Surface structure
Tel: (86) 372 5065802 Fax: (86) 372 5065803
Surface Code
Features Application
structure No.
Spangles condensated on zinc
Conventional
Z coating under normal conditions Commercial purposes
spangle
after galvanizing.
Surface in spangles smaller than Applications where conventional
conventional ones and due to spangles cannot meet the
Small spangle X
controlled condensation of zinc surface appearance
coating. requirements.
Skin passed
G Applications of high surface
spangle Surface structure after special skin
quality requirements, such as
Skin passed pass treatment.
GX color coating base plates.
small spangle
No visible spangles on coating
Zero spangle N surface as a result of a special -
production process.
Zn-Fe alloy R No spangle, gray, normally matte Applicable to further painting
7. Surface treatment
Chromate treatment is a chemical treatment with an aim to prevent
1 Chromate
white rusts formed on product surfaces during transportation and
treatment (L)
storage.
Oiling is to prevent white rusts formed on product surfaces during
2 Oiling (Y)
transportation and storage.
3 Chromate 3 Chromate treatment+ Oiling (LY) This treatment with oiling after
treatment+ Oiling surface chromate treatment is to further avoid the forming of white
(LY) rusts.
8. Surface quality
Code
Features
No.
FB t is allowed for the existence of small erosion spots, dark spots, strip marks, minor
(O3) chromate treatment defects and small zinc particles.
No erosion spot is allowed. However, it is allowed for the existence of light
FC
impression, scratches, zinc flow ripple marks, minor chromate treatment defects in
(O4)
small range, while the other side must reach FB requirements at least.
One side of relatively good quality must further restrict on defects, namely
FD
appearance quality after painting is not affected, and the other side must reach FB
(O5)
requirements at least.
9. Steel grade reference list of the standards, the cited standards and other standards
EN10142:2000 EN 10142:1990
Q/BQB 420-2003 JISG3302-1994ASTMA653M-2002
EN10147:2000 EN 10147:1991
Tel: (86) 372 5065802 Fax: (86) 372 5065803
EN10292:2000
DC51D+Z (St01Z,
DC51D+Z,
St02Z, St03Z) , FeP02GZ, ZF SGCC CS type C
+ZF
DC51D+ZF
DC52D+Z (St04Z), DC52D+Z,
FeP03GZ, ZF SGCC CS type A, type B
DC52D+ZF +ZF
FeP05GZ, ZF SGCD1 FS type A, type B
DC53D+ZF +ZF
FeP06GZ, ZF SGCD2 DDS
DC54D+ZF +ZF
DC56D+Z (St07Z), DC56D+Z, DX56D+Z, +ZF
SGCD3 EDDS
DC56D+ZF +ZF (SEW 021)
Tel: (86) 372 5065802 Fax: (86) 372 5065803

DC54D Z

Uploaded by

Copyright:

Available Formats

DC54D Z

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DC54D Z

Uploaded by

Copyright:

Available Formats

Galvanized Steel Sheets

Galvanized steel sheets

1. Applications and features are given as following table

DC56D+Z (St07Z), DC56D+ZF ≤0.01 ≤0.10 ≤0.30 ≤0.025

4. Mechanical performances and coating adhesiveness

5. Coating weight range

You might also like