Professional Documents
Culture Documents
Design of Portable Coffee Roaster For Home Industr PDF
Design of Portable Coffee Roaster For Home Industr PDF
Abstract. At present, the availability of an appropriate roaster for home coffee processing
industry is very limited. This study aims to design a portable coffee roaster with a maximum
capacity of 2 kg per batch. The roasting machine is designed with six main parts, namely as a
roasting cylinder, an outer cylinder equipped with an inlet-outlet funnel, a main frame, a heat
source with the LPG fuel, a cooling unit, and a temperature control system. The roasting
machine has been tested to roast an amount of green bean at a constant temperature of 225 ͦC
with three targets of roasted degree, namely as light, medium and dark. The test result shows
that the roasting machine can work properly. The temperature control system is able to regulate
the roasting temperature as same as the temperature target during the process. With the stable
temperature, the machine can roast the green coffee sample to reach the target roasted degree
with good result. The test shows that the roaster can roast the sample of 1 kg of green bean at
light roast degree with an average time of 13.2 minutes and an energy consumption of 4708.92
kJ. For the same amount of sample, the coffee roaster can work properly for the roast degree
target of medium with an average time of 16.9 minutes and an energy consumption of 4708.92
kJ. Meanwhile, for dark roasted target, the roaster requires an average time of 28.59 minutes
and consume an energy of 9417.85 kJ.
1. Background
Secondary coffee processing is a series of operation to process coffee beans (green coffee bean) as the
main raw material into ground coffee (ground coffee powder) and its derivative products. This
processing includes a series of stages, starting from the preparation of raw materials, followed by the
roasting, mixing, grinding process, and ending with the development process of coffee derivative
products. Roasting is the most crucial stage on the coffee processing because the flavor formation
process occurs therein. The coffee flavor is produced through a series of physical and chemical
changes in the flavor candidates substance inside coffee [1] [2]. Roasting is a heat treatment process
that aims to form the flavor and aroma of coffee [3] [4]. Coffee roasting is a very important process to
form some organoleptic parameters (taste, aroma, and color) that underlie coffee quality and guarantee
the quality of drinks [5]; [6]. The process takes place at high temperatures (> 200 °C).
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distribution
of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
Published under licence by IOP Publishing Ltd 1
International Conference on Sustainable Agriculture IOP Publishing
IOP Conf. Series: Earth and Environmental Science 327 (2019) 012019 doi:10.1088/1755-1315/327/1/012019
In practice, coffee roasting equipment in the community is quite diverse. Traditional people
generally use a pan that is burned from the bottom side. The heat will be transferred into the upper side
where the coffee beans are placed. The beans will be heated directly with such conduction and
confection procedure. Such roasting process is considered unhealthy, besides being wasteful of energy
due to the very low absorption efficiency of heat. In its development, several roaster machines were
later developed. Unfortunately, commonly roaster is originally developed to support medium and
medium scale coffee processing industries. Today, some coffee roaster machines for the small scale
are available even though they are generally very simple. Besides it often yields the unsatisfactory
results, commercial roaster is very wasteful of energy and is considered less practical. The
considerable demand for small coffee roaster machines and the limitations of the commercially
available coffee roaster machines have encouraged researchers to develop these roasted machines in
the last two years. This study aims to design and construct make small-scale of portable coffee roaster
with high efficiency of energy for home coffee industry.
2
International Conference on Sustainable Agriculture IOP Publishing
IOP Conf. Series: Earth and Environmental Science 327 (2019) 012019 doi:10.1088/1755-1315/327/1/012019
initial design had a capacity of 0.5 kg / batch, which was consisted of two main parts, namely as a
roasting cylinder and outer cylinder (cover). This first-generation roaster machine was operated
manually with a gas stove as heating source. The manual roaster had been tested. The result showed
that it could work well with good performance. One of the roaster disadvantages was the
unsatisfactory roasted coffee, especially when it is viewed from the color uniformity of the roasted
coffee. The manual stirring process was suspected to be the cause of the roast maturity level.
Therefore, at the next development work, a roasting machine with the same capacity was designed by
adding an electric motor to rotate the roasting cylinder continuously. The test results showed that the
roaster prototype worked better than previously design. It was able to roast the sample of green coffee
with uniform roasting level. The second prototype was kept to develop such roaster for the next
experiment. On the third roasting generation, we focused on improving the second design, especially
by adding the capacity up to 2 kg per batch and improving the heating source using special burner for
LPG fuel. Design of this roaster is presented in Figure 1.
3
International Conference on Sustainable Agriculture IOP Publishing
IOP Conf. Series: Earth and Environmental Science 327 (2019) 012019 doi:10.1088/1755-1315/327/1/012019
thermo-control unit. While the cooling unit consists of a tube with a device made of perforated
stainless plate. This part is also equipped with a blower unit which serves to suck heat when the
cooling process takes place. The main frame part is designed from elbow-profile iron, functions to
install all components of the roaster.
After the final design of the roasting prototype is completed, the next step is calculating the
construction materials. Based on the design, necessary construction materials can be estimated. After
determined, the next step is buying the materials. In this procurement, materials are purchased in
stages based on the level of urgency. A number of prioritized materials include stainless steel plate,
perforated stainless steel plate, and elbow iron. After all materials have been received, the next activity
is manufacturing. The manufacturing activity begins with preparing of construction equipment that
will be used to construct the roaster. The production machines used for manufacturing activities
include cutting machines, grinders, lathes, milling machines, bending machines, roller machines, and
welding machines. Constructing the roaster starts with part by part. Starting with six main parts
construction, the activities is then continued to create other supporting parts. After all parts are
manufactured, then they are assembled. The results of the portable roaster is presented in Figure 2.
4
International Conference on Sustainable Agriculture IOP Publishing
IOP Conf. Series: Earth and Environmental Science 327 (2019) 012019 doi:10.1088/1755-1315/327/1/012019
4. Conclusion
Research on design and construction have been carried out, resulted a prototype of small-scale
portable coffee roaster for home industry of coffee. The prototype was operated with LPG gas, using
perforated roaster cylinder, and had a capacity of 2.5 kg per batch. The roaster consisted of six main
parts, i.e. namely as a roasting cylinder, an outer cylinder equipped with an inlet-outlet funnel, a main
frame, a heat source with the LPG fuel, a cooling unit, and a temperature control system. This roaster
could be operated easily. The material of green coffee was inserted through the input funnel and was
channelled to the roasting cylinder after the roast temperature was reached. The roasting temperature
could be adjusted easily, making it possible to roast the green coffee according to the desired
temperature condition. The performance test showed that the portable roaster machines worked well.
With a green coffee sample of 1 kg per batch, the machine was able to roast the sample till to the
target of light, medium, and dark with a roasting time of 13.2; 16.9; and 28.59 minutes respectively.
5. Acknowledgements
This work was supported by many contributors; thus, we would like to thank to Faculty of
Agricultural Technology, Universitas Gadjah Mada, and Indonesia Toray Science Foundation (ITSF).
We also thank to CV. Faathira Alam for anything support for this design and construction.
References
[1] Sri Mulato, Edi Suharyanto, and Kaswanto, Products Development of Coffee. Indonesian Coffee
and Cocoa Research Institute, Jl. PB. Sudirman No. 90, Jember 68118 - Indonesia, 2010.
[2] H.-S. Chung, D.-H. Kim, K.-S. Youn, J.-B. Lee, and K.-D. Moon, “Optimization of roasting
conditions according to antioxidant activity and sensory quality of coffee brews,” Food Sci.
Biotechnol., vol. 22, no. 1, pp. 23–29, Feb. 2013.
[3] O. Gonzalez-Rios et al., “Impact of ‘ecological’ post-harvest processing on coffee aroma: II.
Roasted coffee,” J. Food Compos. Anal., vol. 20, no. 3, pp. 297–307, May 2007.
[4] H.-D. Belitz, W. Grosch, and P. Schieberle, Food Chemistry. Springer Science & Business Media,
2009.
[5] J. A. Hernández, B. Heyd, C. Irles, B. Valdovinos, and G. Trystram, “Analysis of the heat and
mass transfer during coffee batch roasting,” J. Food Eng., vol. 78, no. 4, pp. 1141–1148, Feb.
2007.
[6] J. A. Hernández, B. Heyd, and G. Trystram, “Prediction of brightness and surface area kinetics
during coffee roasting,” J. Food Eng., vol. 89, no. 2, pp. 156–163, Nov. 2008.