Renderoc SXtra
Renderoc SXtra
Uses Properties
Renderoc SXtra is suitable for hand application to repairs The following typical results were obtained at a water to
where significant load bearing is required. Typical applica- powder ratio of 0.15.
tions would include, but not be limited to, the following :
Test method Typical result
Vertical and overhead repairs Drying shrinkage to ASTM C 157-93
7 days : < 300 microstrain
Patch repairs to concrete floor slabs 28 days : < 500 microstrain
Permeability : < 10 mm
Patch repairs to stairs, steps and other areas subject to
(DIN 1048 Part 5)
repeated, heavy trafficking Flexural strength : > 7 N/mm2 at 28 days
Arris repairs to joint edges (BS 6319 Pt.3)
Tensile strength : > 3.5 N/mm2 at 28 days
General structural repairs where formwork cannot be (BS 6319 Pt.7)
easily erected Compressive strength : Tolerance (±10%)
(BS 1881 Pt.1161) : 35 N/mm2 at 3 days
Advantages 45 N/mm2 at 7 days
55 N/mm2 at 28 days
Renderoc SXtra features Dimensional Stability Technolo- Water absorption : < 2%
gy - a new materials technology which controls the rate of (BS 1881 Pt.122)
drying shrinkage such that, when used correctly : Note1: 50mm cubes, air cured @ 250C
i. the dimensions of the repair remain stable; and thus
Design criteria
ii. eliminating failure, due to shrinkage cracking.
Dimensional Stability Technology is a major step forward
This in turn leads to a series of associated benefits : in the general compatibility of repair mortar systems with the
host substrate, and the control of drying shrinkage in particu-
Cost effective - shrinkage control enables repairs to be lar.
completed ‘right first time’ Attention to the basic design criteria given below should
ensure that the full benefits of this technology are gained in
Enhanced durability - works in tandem with extremely
use :
low permeability to prolong effective working life
(i) Recommended limits for a single application are:
Compatibility - aligns performance closer than ever
before, to that of host concrete Minimum applied thickness : 5 mm
Overhead sections : up to 25 mm thick
User friendly - specifically developed to provide an Vertical sections : up to 35 mm thick
easy-to-apply product, suitable for local conditions Small pockets or horizontal : up to 100 mm thick
Definable performance - positive benefits are easily Maximum length : up to 3 m
demonstrated via a single, simple measurement
NOTE : If the repair area exceeds 2.5 m2, consideration
should be given to the use of mass fill by means
Description of either Renderoc SPXtra* spray applied mortar
Renderoc SXtra is supplied as a ready to use blend of dry or Renderoc LAXtra* microconcrete.
powders, which requires only the addition of clean water to (ii) In situations where a substrate/repair barrier is required,
produce a highly consistent repair mortar suitable for most or enhanced bond strength/working time is required, or
structural and load bearing repairs. where the substrate is likely to be damp (e.g. seawalls,
quays etc.), Nitobond EP epoxy bonding agent should be
used.
Renderoc SXtra should be mixed and applied in strict accord- Health and safety
ance with the Product Method Statement, a copy of which
Renderoc SXtra contains cement powders which, when
may be obtained from your nearest Fosroc office.
mixed with water or upon becoming damp, release alkalis
which can be harmful to the skin.
Estimating
During use, avoid inhalation of the dust and contact with the
Supply
skin or eyes. Wear suitable protective clothing - eye protec-
Renderoc SXtra : 25 kg bags tion, gloves and respiratory equipment (particularly in
confined spaces).
Yield
The use of barrier creams to provide additional skin protec-
Renderoc SXtra : 12.5 litres per 25 kg bag
tion is also advised. In case of contact with the skin, rinse
with plenty of clean water, then cleanse thoroughly with soap
Limitations
and water.
- Renderoc SXtra should not be used when the ambient
In case of contact with eyes, rinse immediately with plenty of
temperature is below 50C and falling.
clean water and seek medical advice. If swallowed seek
- Renderoc SXtra should not be part mixed, nor part bags medical attention immediately - do not induce vomiting.
used.
Fire
- Renderoc SXtra should not be exposed to running water
Renderoc SXtra, is non-flammable and presents no fire
either during application or prior to final set.
hazard.
- Water ponding is not recommended for curing.
For further information, please refer to the respective
Product Material Safety Data Sheet for Renderoc SXtra.
Storage
Shelf life
Standards compliance
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.
Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: [email protected]
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: [email protected]
Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: [email protected]
United Arab Emirates Kuwait, Boodai telephone: 4817618 fax: 4832124 email: [email protected]
Oman, Al Amana telephone: 24815080 fax: 24817554 email: [email protected]
www.fosroc.com
UAE/0252/18/J