Professional Documents
Culture Documents
RF Steel Fatigue Members Manual en PDF
RF Steel Fatigue Members Manual en PDF
December 2014
Add-on Module
Program Description
Contents
Contents Page
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Add-on Module RF-STEEL Fatigue Members . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Using the Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Opening RF-STEEL Fatigue Members Add-on Module . . . . . . . . . . . . . 4
2. Theoretical Principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Design Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Design with Damage Equivalent Factors . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.1 Design Equations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.2 Stress Range 𝛥𝜎 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2.3 Damage Equivalent Factor 𝜆 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3. Input Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 General Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.3 Cross-Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.4 Detail Categories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4. Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1 Detail Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1.1 Ultimate Limit State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1.2 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.2 Calculation Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5. Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.1 Design by Cross-Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.2 Design by Set of Members . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.3 Design by Member . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.4 Design by x-Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.5 Parts List by Member . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.6 Parts List by Set of Members . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6. Results Evaluation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.1 Results in RFEM Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.2 Result Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.3 Filter for Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7. Printout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.1 Printout Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.2 Graphic Printout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.2.1 Results in RFEM Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.2.2 Result Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8. General Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.1 Design Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
8.2 Cross-Section Optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
8.3 Units and Decimal Places . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
8.4 Data Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
8.4.1 Exporting Materials to RFEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
8.4.2 Exporting Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
9. Example: Tubular Truss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
9.1 System and Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
9.2 Design in RF-STEEL Fatigue Members . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
1
Contents
2
1 Introduction 1
1 Introduction
1.1 Add-on Module RF-STEEL Fatigue Members
The fatigue designs according to EN 1993-1-9 [1] are based on the so-called nominal stress concept.
This method analyzes the influence of material fatigue on a structure. Many damages in a steel
structure are affiliated to recurring effects stressing the particular points of the construction until
the fatigue failure occurs. The RF-STEEL Fatigue Members add-on module performs the fatigue
designs using the method of damage equivalent factors.
The following useful features facilitate the work with the add-on module:
• Determination of stress ranges for selected load cases, load or result combinations
• Free assignment of detail categories to the stress points of cross-sections
• User-defined specification of the damage equivalent factors
Since RF-STEEL Fatigue Members is integrated in the main program, the general input data and
internal forces are already available for the design. It is possible to evaluate designs and stress
ranges graphically in the RFEM work window and to associate them in the global printout report.
The analysis determines the maximal design ratios of sets of members. Furthermore, RF-STEEL
Fatigue Members allows an automatic cross-section optimization including the export of modified
cross-section to RFEM.
Using the design cases, you can analyze different types of stress designs. A parts list with quantity
surveying completes the design.
3
1 Introduction 1
1.2 Using the Manual
Topics like installation, graphical user interface, results evaluation, and printout are described
in detail in the manual of the main program RFEM. The present manual focuses on typical features
of the RF-STEEL Fatigue Members add-on module.
The descriptions in this manual follow the sequence and structure of the module's input and result
windows. In the text, the described buttons are given in square brackets, for example [View mode].
At the same time, they are pictured on the left. Expressions appearing in dialog boxes, windows,
and menus are set in italics to clarify the explanation.
At the end of the manual, you find the index. However, if you still cannot find what you are
looking for, please check our website www.dlubal.com where you can go through our FAQ pages
by selecting particular criteria.
Menu
To open the program from the RFEM menu bar, click
Add-on Modules → Design - Steel → RF-STEEL Fatigue Members.
Figure 1.1: Menu: Add-on Modules → Design - Steel → RF-STEEL Fatigue Members
4
1 Introduction 1
Navigator
As an alternative, you can open the add-on module in the Data navigator by clicking
Add-on Modules → RF-STEEL Fatigue Members.
Panel
If results from RF-STEEL Fatigue Members are already available in the RFEM model, you can also
open the design modules from the panel:
Set the relevant design case in the load case list of the RFEM toolbar. Click [Show Results] button
to graphically display the stresses and stress ratios.
When the result display is activated, the panel is available, too. Now you can use the [RF-STEEL
Fatigue Members] button in the panel to open the module.
5
2 Theoretical Principles 2
2 Theoretical Principles
2.1 Design Concept
The fatigue designs according to EN 1993-1-9 [1] are based on the so-called nominal stress concept.
The internal forces are determined according to the structural analysis for members; the stresses
are calculated according to the mechanics of materials at the location where the crack formation
is expected. In fatigue design, the nominal stress ranges 𝛥𝜎 and 𝛥𝜏 , as a result of the actions, are
compared with design values of the fatigue strength 𝛥𝜎R and 𝛥𝜏R . Furthermore, the concept of
the partial safety factors is valid in [1]. The partial safety factor 𝛾Mf for the fatigue strength is graded
according to the reliability concept and the possible consequences of failure. The following table
shows the recommendations:
The stresses on the action side are to be determined by a serviceability level. For the partial safety
factor 𝛾Ff , the value 𝛾Mf = 1.0 applies to the actions.
The Standard [1] provides the following design methods:
• Design with fatigue strength
• Design by means of damage accumulation
• Design with damage equivalent factors
In the RF-STEEL Fatigue Members add-on module, the design is carried out by means of damage
equivalent factors. Therefore, only this design method is described in the manual.
6
2 Theoretical Principles 2
2.2 Design with Damage Equivalent Factors
This method represents the standard method according to [1]. The damage equivalent stress
ranges 𝛥𝜎E,2 and 𝛥𝜏E,2 related to 2 ⋅ 106 stress cycles are to be contrasted with the limit values
of the fatigue strength 𝛥𝜎C or 𝛥𝜏C for 2 ⋅ 106 cycles of the corresponding detail category under
consideration of partial safety factors.
1.5 ⋅ 𝑓𝑦
𝛥𝜏 ≤ √ (2.2)
3
Fatigue designs
Fatigue designs for normal and shear stresses are limited according to [1], Eq. 8.2 as follows:
𝛾𝐹 𝑓 ⋅ 𝛥𝜎𝐸 ,2
≤ 1.0 (2.3)
𝛥𝜎𝐶 /𝛾𝑀 𝑓
𝛾𝐹 𝑓 ⋅ 𝛥𝜏𝐸 ,2
≤ 1.0 (2.4)
𝛥𝜏𝐶 /𝛾𝑀 𝑓
Simultaneous effect of normal and shear stresses
According to [1], Eq. 8.3, also the following design criteria are to be satisfied:
𝛾𝐹 𝑓 ⋅ 𝛥𝜎𝐸 ,2 3 𝛾𝐹 𝑓 ⋅ 𝛥𝜏𝐸 ,2 3
( ) +( ) ≤ 1.0 (2.5)
𝛥𝜎𝐶 /𝛾𝑀 𝑓 𝛥𝜏𝐶 /𝛾𝑀 𝑓
Determination of partial safety factors 𝛾Mf and 𝛾Ff is described in Chapter 2.1.
The fatigue strength 𝛥𝜎C or 𝛥𝜏C for 2 ⋅ 106 cycles are assigned to the respective detail categories
in [1]. You can deduce the normal or shear stress ranges from the following diagrams.
7
2 Theoretical Principles 2
8
2 Theoretical Principles 2
2.2.2 Stress Range 𝛥𝜎
The stress range describes the difference between the maximum and the minimum normal or
shear stress (also called top and bottom stress). These are defined as follows:
𝛥𝜎 = 𝜎𝑚 𝑎𝑥 − 𝜎𝑚 𝑖 𝑛 (2.6)
Figure 2.4: Stress ranges and influence of internal tensile stresses according to [2]
If there is no information on the damage equivalent factors 𝜆, the design requirements according
to [1], Annex A are applied. Then the nominal stress results from the damage equivalent factors
and the stress range.
𝛾𝐹 𝑓 ⋅ 𝛥𝜎𝐸 ,2 = 𝜆 ⋅ 𝛥𝜎 (2.7)
𝛾𝐹 𝑓 ⋅ 𝛥𝜏𝐸 ,2 = 𝜆 ⋅ 𝛥𝜏 (2.8)
9
3 Input Data 3
3 Input Data
After you open the add-on module, a new window appears. In this window, a navigator is dis-
played on the left, managing the tables that can be selected currently. The drop-down list above
the navigator contains the design cases (see Chapter 8.1, page 37).
The design-relevant data is defined in several input windows. When you open RF-STEEL Fatigue
Members for the first time, the following parameters are imported automatically:
• Members and sets of members
• Load cases, load and result combinations
• Materials
• Cross-sections
• Internal forces (in background, if calculated)
To select a window, click the corresponding entry in the navigator. To set the previous or next input
window, use the buttons shown on the left. For scrolling in windows, you can also use the function
keys to select the next [F2] or previous [F3] window.
[OK] saves the results. Thus, you exit RF-STEEL EC3 and return to the main program. To exit
the add-on module without saving the new data, click [Cancel].
10
3 Input Data 3
Design of
The design can be carried out for Members as well as for Sets of Members. If you want to design only
selected objects, clear the All check box. Then you can access the text boxes to enter the numbers
of the relevant members or sets of members. You can remove the list of preset numbers in the text
box using the [Delete] button. Use the [Select] button to display the objects graphically in the RFEM
work window.
When you design a set of members, the program determines the maximum stress ratio of all
members contained in the set of members. The results are shown in result windows 2.2 Design by
Set of Members and 4.2 Parts List by Set of Members.
Click [New] to create a new set of members. The dialog box that you already know from RFEM
appears where you can specify the parameters for a set of members.
Comment
In this text box, you can enter user-defined notes, for example to describe the current design case.
11
3 Input Data 3
3.2 Materials
The window is subdivided into two parts. The upper part lists all materials created in RFEM. The Ma-
terial Properties section shows the properties of the current material, that is, the table row currently
selected in the upper section.
Materials that will not be used in the design are dimmed. Materials that are not allowed are
highlighted in red. Modified materials are displayed in blue.
The material properties required for the determination of internal forces are described in Chap-
ter 4.3 of the RFEM manual (Main Properties). The material properties required for design are stored
in the global material library. These values are preset (Additional Properties).
You can adjust the units and decimal places of material properties and stresses using the menu
Settings → Units and Decimal Places (see Chapter 8.3, page 41).
Material Description
The materials defined in RFEM are preset, but you can always modify them: To do this, click the ma-
terial in column A. Then click or press function key [F7] to open the material list.
12
3 Input Data 3
When you have imported a material, the design-relevant Material Properties are updated.
If you change the material description manually and the entry is stored in the material library,
RF-STEEL Fatigue Members will import the material properties, too.
Generally, the material properties are not editable in the RF-STEEL Fatigue Members add-on mod-
ule.
Material Library
Numerous materials are already available in the library. To open the library, click
Edit → Material Library
or use the button shown on the left.
The following Material Library dialog box appears.
In the Filter section, the current Standard group is preset. Select the specific material in the Material
to Select list. You can check the corresponding properties in the dialog section below.
Click [OK] or use the [↩] button to transfer the selected material to Window 1.2 of RF-STEEL Fatigue
Members.
Chapter 4.3 of the RFEM manual describes in detail how materials can be filtered, added, or re-
arranged.
You can also select materials of categories Cast Iron and Stainless Steel. Please check, however,
whether these materials are allowed by the design concept of the Standard [1].
13
3 Input Data 3
3.3 Cross-Sections
This window lists the cross-sections used for design. In addition, you can specify optimization
parameters here.
Cross-Section Description
The cross-sections defined in RFEM are preset together with the assigned material numbers.
If you want to modify a cross-section, click the entry in column B. Click [Cross-Section Library] or
in the box or press function key [F7] to open the cross-section table of the current cross-section
box (see the following figure).
In this dialog box, you can select a different cross-section type. To select a different cross-section
category, click [Back to cross-section library] to access the general cross-section library.
Chapter 4.13 of the RFEM manual describes how cross-sections can be selected from the library.
14
3 Input Data 3
You can directly enter a new cross-section description in the input window. If the entry is listed in
the database, RF-STEEL Fatigue Members imports these cross-sections parameters, too. A modified
cross-section will be highlighted in blue.
If the cross-sections in RF-STEEL Fatigue Members are different from the ones used in RFEM,
both cross-sections are displayed in the graphic on the right. The designs will be performed
for the cross-section selected in RF-STEEL Fatigue Members, using the internal forces from RFEM.
Optimize
You can optimize every cross-section from the library: For the RFEM internal forces, the pro-
gram searches the cross-section that comes as close as possible to a user-defined maximum
ratio. You can define the maximum ratio in the Details dialog box (see Figure 4.2, page 20).
If you want to optimize a cross-section, open the corresponding drop-down list in column D or E
and select the desired entry: From current row or, if available, From favorites ‘Description’. Recom-
mendations for the cross-section optimization can be found in Chapter 8.2 on page 38.
Remark
This column shows remarks in the form of footers that are explained below the cross-section list.
A warning might appear before the calculation: Incorrect type of cross-section! It means that there
is a cross-section that is not stored in the database. This may be a user-defined cross-section or
a SHAPE-THIN cross-section that has not been calculated yet. To select an appropriate cross-section
for the design, click the [Library] button (see description below Figure 3.5).
15
3 Input Data 3
Member with Tapered Cross-Section
For tapered members with different cross-sections at the member start and member end, the mod-
ule displays both cross-section numbers in two rows, in accordance with the definition in RFEM.
RF-STEEL Fatigue Members also designs tapered members, provided that the cross-section at
the member start has the same number of stress points as the cross-section at the member end.
For example, the normal stresses are determined from the moments of inertia and the centroidal
distances of the stress points. If the cross-section at the start and the end of a tapered member have
a different number of stress points, the intermediate values cannot be interpolated. The calculation
is possible neither in RFEM nor in RF-STEEL Fatigue Members.
To produce the same number of stress points, you can, for example, define the second cross-section
as a copy of the cross-section start with adjusted geometry parameters. The easiest way to do
this is to describe both cross-sections as parametric profiles. In such case, the cross-section type
IVU I-Section Plus Lower Flange is recommended.
Stress points of the cross-section including numbering can also be checked graphically: Select
the cross-section in Window 1.3 and click the [Info] button. The dialog box shown in Figure 3.7
appears.
Cross-Section Graphic
The right part of the window shows the currently selected cross-section.
The buttons below the graphic have the following functions:
Button Function
Open the Info About Cross-Section dialog box (see Figure 3.7)
Display or hide the cross-section dimensions
Display or hide the principal axes of the cross-section
Display or hide the stress points
Display or hide the numbering of stress points
Reset full view of the cross-section graphic
16
3 Input Data 3
Info About Cross-Section
In the Info About Cross-Section dialog box, you can see the cross-section properties, stress points,
and c/t-parts.
Click [Details] to call up detailed information on stress points (centroidal distances, statical mo-
ments of area, warping constants etc.) and c/t-parts.
17
3 Input Data 3
3.4 Detail Categories
In the 1.4 Detail Categories window, you can define the fatigue strength of members previously
selected for the design in Window 1.1.
18
4 Calculation 4
4 Calculation
4.1 Detail Settings
Before you start the [Calculation], it is recommended to check the design details. You can access
the corresponding dialog box in all windows of the add-on module by using the [Details] button.
The Details dialog box consists of the following tabs:
• Ultimate Limit State
• General
Assessment Method
The reliability concept and possible consequence of failure affect the partial safety factor 𝛾Mf
considered when determining the fatigue strength. You can set this partial safety factor using
the option Damage tolerant or Safe life together with the Consequence of failure (low or high).
You can also specify the partial factor 𝛾Mf for fatigue strength directly.
[1], Table 3.1 shows recommendations for the factor 𝛾Mf (see Figure 2.1, page 6).
19
4 Calculation 4
4.1.2 General
Cross-Section Optimization
The optimization is targeted on the maximum stress ratio of 100 %. If necessary, you can set
a different design ratio in this text box.
20
4 Calculation 4
4.2 Calculation Start
In all input windows of the RF-STEEL Fatigue Members add-on module, you can start the calcula-
tion using the [Calculation] button.
RF-STEEL Fatigue Members searches for the results of the load cases, load combinations and result
combinations to be designed. If these cannot be found, the program starts the RFEM calculation
to determine the design-relevant internal forces.
You can also start the calculation in the RFEM user interface: The To Calculate dialog box (menu
Calculate → To Calculate) lists design cases of the add-on modules like load cases and load com-
binations.
If the RF-STEEL Fatigue Members design cases are missing in the Not Calculated section, select All
or Add-on Modules in the drop-down list below the section.
Use the button to transfer the selected RF-STEEL Fatigue cases to the list on the right. Click
[OK] to start the calculation.
To calculate a design case directly, you can also use the list in the toolbar: Select the RF-STEEL
Fatigue Members design case in the toolbar list and click [Show Results].
Subsequently, you can see the design process in a separate dialog box.
21
5 Results 5
5 Results
The 2.1 Design by Cross-Section window is displayed immediately after the calculation.
The designs are shown in result windows 2.1 to 2.5, sorted by different criteria.
Windows 4.1 and 4.2 show the parts lists by member and set of members.
Every window can be selected by clicking the corresponding entry in the navigator. To set the pre-
vious or next window, use the buttons shown on the left. You can also use the function keys to
select the next [F2] or previous [F3] window.
[OK] saves the results. You exit RF-STEEL Fatigue Members and return to the main program.
Chapter 5 - Results describes the different result windows one by one. The evaluation of and
checking results is described in Chapter 6 - Results Evaluation, page 29 ff.
22
5 Results 5
5.1 Design by Cross-Section
In this result window, the maximum design ratios of all designed members and actions are listed
by cross-section. The ratios for the internal forces of the governing load cases and combinations
are sorted by stress type.
Section No.
The results are listed by cross-section number. The description of the cross-section is displayed
on the right of the cross-section number.
Member No.
It shows the number of the member with the maximum design ratio of the design type indicated
in column F.
Location x
This column shows the respective x-location where the member's maximum design ratio occurs.
For the output in form of tables, the program uses the following member locations x:
• Start and end node
• Division points according to possibly defined member division (see RFEM Table 1.16)
• Member division according to specification for member results (Calculation Parameters dialog
box, Global Register Parameters tab in RFEM)
• Extreme values of internal forces
23
5 Results 5
S-point No.
The design is carried out on certain stress points of the cross-section. These points are defined
by centroidal distances, statical moments, and cross-section thicknesses, which allow for design
according to [1]. The cross-section dialog graphic in the bottom right shows the currently selected
stress point (that means the stress point of the table row where the pointer is placed) highlighted
in red.
To check the stress point properties, click the [Info] button (see Chapter 3.2, page 17).
Design Ratio
Columns D and E show the design conditions according to [1].
The length of colored bars represents the respective design ratios.
This result window appears when you have selected at least one set of members for the design.
The window lists the maximum design ratios sorted by set of members.
The column Member No. shows the number of the one member within the set of members that
bears the maximum stress ratio for the respective stress types.
The output by sets of members clearly presents the design for an entire structural group (for
example a continuous beam).
24
5 Results 5
5.3 Design by Member
This result window presents the maximum design ratios for different stress types sorted by member
number. The columns are described in detail in Chapter 5.1 on page 23.
If there is a tapered member, both cross-section descriptions are displayed in the table row next
to the section number.
25
5 Results 5
5.4 Design by x-Location
This result window lists the maximum stresses for each member at all location x resulting from
the division points defined in RFEM:
• Start and end node
• Division points according to possibly defined member division (see RFEM Table 1.16)
• Member division according to specification for member results (Calculation Parameters dialog
box, Global Register Parameters tab in RFEM)
• Extreme values of internal forces
26
5 Results 5
5.5 Parts List by Member
Finally, there is a summary of all cross-sections included in the design case.
By default, this list contains only the designed members. If you need a parts list for all members
of the model, select the corresponding option in the Details dialog box (see Figure 4.2, page 20).
Part No.
The program automatically assigns part numbers to similar members.
Cross-Section Description
This column lists the cross-section numbers and descriptions.
Number of Members
This column shows how many similar members are used for each part.
Length
This column shows the respective length of an individual member.
Total Length
This column shows the product determined from the two previous columns.
Surface Area
For each part, the program indicates the surface area relative to the total length. The surface area
is determined from the Surface Area of the cross-sections that can be seen in Windows 1.3 and
2.1 to 2.5 in the cross-section properties (see Figure 3.7, page 17).
27
5 Results 5
Volume
The volume of a part is determined from the cross-sectional area and the total length.
Unit Weight
The Unit Weight of the section is relative to the length of one meter. For tapered cross-sections,
the program averages both cross-section weights.
Weight
The values of this column are determined from the respective product of the entries in columns C and G.
Total Weight
The final column indicates the total weight of each part.
Sum
At the bottom of the list, you find a summary of the values in the columns B, D, E, F, and I. The last
row of the Total Weight column informs you about the total amount of required steel.
The last result window is displayed if you have selected at least one set of members for design.
The window summarizes an entire structural group (for example a horizontal beam) in a parts list.
Details on the various columns can be found in the previous Chapter 5.5. If there are different
cross-sections used in a set of members, the program averages the surface area, the volume and
the cross-section weight.
28
6 Results Evaluation 6
6 Results Evaluation
For the evaluation process, you can use the buttons below the table.
Display only the rows with the filter parameter applied (design
Apply Filter
ratio > 1, maximum, user-defined limit)
Open the Result Diagram on Member window
Result Diagrams
→ Chapter 6.2, page 31
Export the table to MS Excel / OpenOffice
Excel Export
→ Chapter 8.4.2, page 42
Member Selection Select a member graphically to display its results in the table
View Mode Jump to the RFEM work window to change the view
29
6 Results Evaluation 6
RFEM Background Graphic and View Mode
The RFEM work window in the background is useful when you want to find the position of a par-
ticular member in the model: The member selected in the result window of RF-STEEL Fatigue
Members is highlighted in the selection color in the background graphic. An arrow indicates also
the member's x-location that is displayed in the active table row.
Figure 6.2: Indication of member and current Location x in the RFEM model
In case you cannot improve the display by moving the RF-STEEL EC3 module window, click [Jump
to Graphic] to activate the View mode: The program hides the window so that you can modify
the display in the RFEM user interface. The view mode provides the functions of the View menu,
for example zooming, moving, or rotating the display. The pointer remains visible.
Click [Back] to return to the RF-STEEL Fatigue Members add-on module.
30
6 Results Evaluation 6
If you select a multicolor representation (options With/Without Diagram or Cross-Sections), the color
panel becomes available, providing common control functions. These functions are described
in detail in the RFEM manual, Chapter 3.4.6.
Figure 6.4: Design ratios with display options With Diagram and Result Diagrams Filled
You can transfer the graphics of stresses and design ratios to the printout report (see Chapter 7.2,
page 35).
To return to the add-on module, click [RF-STEEL Fatigue Members] in the panel.
31
6 Results Evaluation 6
by clicking the button shown on the left. The button is located below the upper result table (see
Figure 6.1, page 29).
To display the result diagrams, select the command from the RFEM menu
Results → Result Diagrams for Selected Members
or use the corresponding button in the RFEM toolbar.
A window opens, graphically showing the distribution of the results on the member or set of mem-
bers.
Use the list in the toolbar above to choose the relevant RF-STEEL Fatigue Members design case.
The Result Diagram on Member dialog box is described in detail in the RFEM manual, Chapter 9.5.
Filtering Designs
The design ratios can easily be used as filter criteria in the RFEM work window, which can be
accessed by clicking [Graphics]. To apply this function, the panel must be displayed. If the panel
is not active, you can activate it in the RFEM menu by clicking
View → Control Panel (Color Scale → Factors → Filter)
or use the toolbar button shown on the left.
32
6 Results Evaluation 6
The panel is described in the RFEM manual, Chapter 3.4.6. The filter settings for the results must
be defined in the first panel tab (Color scale). As this tab is not available for the two-colored
results display, you have to set the display option Colored With/Without Diagram or Cross-Sections
in the Display navigator.
As the figure above shows, the color scale can be set in such a way that only stress ranges greater
than 45 N/mm2 are shown in a color range between blue and red. Furthermore, the color scale
can be adjusted in such a way that one color range covers exactly 2.5 N/mm2, for example.
The Display Hidden Result Diagram function in the Display navigator (Results → Members) shows
all stress diagrams that are not within this value spectrum. Those diagrams are represented by
dotted lines.
Filtering Members
In the Filter tab of the control panel, you can specify the numbers of particular members to display
their results filtered. This function is described in detail in the RFEM manual, Chapter 9.9.3.
33
6 Results Evaluation 6
In contrast to the visibility function, the model will be displayed completely in the graphic. The fig-
ure above shows the stress ranges of a beam. The remaining designed members are displayed in
the model but without 𝛥𝜎 results.
34
7 Printout 7
7 Printout
7.1 Printout Report
Similar to RFEM, the program generates a printout report for the RF-STEEL Fatigue Members results,
to which you can add graphics and descriptions. The selection in the printout report determines
what data from the design module will be included in the printout.
The printout report is described in the RFEM manual. In particular, Chapter 10.1.3.4 Selecting
Data of Add-on Modules describes how to select input and output data from add-on modules for
the printout report.
For complex structural systems with many design cases, it is recommended to split the data
into several printout reports, thus allowing for a clearly-arranged printout.
Figure 7.2: Button Print in the dialog box Result Diagram on Member
35
7 Printout 7
The dialog box is described in the RFEM manual, Chapter 10.2. The RFEM manual also describes
the Options and Color Scale tab.
You can move the graphic anywhere within the printout report by using the drag-and-drop func-
tion.
To adjust a graphic subsequently in the printout report, right-click the relevant entry in the naviga-
tor of the printout report. The Properties option in the shortcut menu opens the Graphic Printout
dialog box, offering various options for adjustment.
36
8 General Functions 8
8 General Functions
This chapter describes useful menu functions as well as export options for the designs.
In this dialog box, enter a Number (that is still available) for the new design case. The corresponding
Description makes the selection in the load case list easier
Click [OK] to open the RF-STEEL Fatigue Members window 1.1 General Data where you can enter
the design data.
In this dialog box, you can specify a different Description as well as a different Number of the design
case.
37
8 General Functions 8
The following dialog box appears:
You can select a design case in the list of Available Cases. To delete the selected case, click [OK].
During the optimization process, RF-STEEL Fatigue Members determines the cross-section that
fulfills the analysis requirements in the most “optimal” way, that is, it comes as close as possible to
38
8 General Functions 8
the maximum allowable design ratio specified in the Details dialog box (see Figure 4.2, page 20).
The required cross-section properties are determined with the internal forces from RFEM. If an-
other cross-section proves to be more favorable, this cross-section is used for the design. Then,
the graphic in Window 1.3 shows two cross-sections: the original cross-section from RFEM and
the optimized one (see Figure 8.7).
When optimizing a parametrized cross-section, the Optimization dialog box appears.
By selecting the check boxes in the Optimize column, you decide which parameter(s) you want to
modify. This enables the Minimum and Maximum columns, where you can specify the upper and
lower limits of the parameter. The Increment column determines the interval in which the size of
the parameter varies during the optimization process.
If you want to Keep current side proportions, select the corresponding check box. In addition,
you have to select at least two parameters for optimization.
Cross-sections composed of combined rolled cross-sections cannot be optimized.
Please note that the internal forces are not automatically recalculated with the modified cross-sec-
tions during the optimization: It is up to you to decide which cross-sections should be transferred
to RFEM for recalculation. As a result of optimized cross-sections, the internal forces may differ
significantly because of the modified stiffnesses in the structural system. Therefore, it is recom-
mended to recalculate the internal forces of the modified model data after the first optimization
and then to optimize the cross-sections once again.
You can export the modified cross-sections to RFEM: Go to the 1.3 Cross-Sections window and click
Edit → Export All Cross-Sections to RFEM.
You can also use the shortcut menu in Window 1.3 to export optimized cross-sections to RFEM:
39
8 General Functions 8
Before the modified cross-sections are transferred to RFEM, a security query appears as to whether
the results of RFEM should be deleted.
By confirming the query and starting the [Calculation] in the RF-STEEL Fatigue Members module,
the RFEM internal forces as well as the design ratios will be determined in one single calculation
run.
If the modified cross-sections have not been exported to RFEM yet, you can reimport the original
cross-sections in the design module by using the options shown in Figure 8.7. Please note that
this option is only available in the 1.3 Cross-Sections window.
If you optimize a tapered member, the program modifies the member start and end and linearly
interpolates the second moments of area for the intermediate locations. Since these moments are
considered with the fourth power, the designs may be inaccurate if the depths of the start and
end cross-section differ considerably. In such a case, it is recommended to divide the taper into
several members, thus modeling the taper layout manually.
40
8 General Functions 8
8.3 Units and Decimal Places
Units and decimal places of RFEM and the add-on modules are managed in one dialog box.
In RF-STEEL Fatigue Members, you can use the menu to adjust the units. To open the correspond-
ing dialog box, click
Settings → Units and Decimal Places.
The following dialog box appears which you already know from RFEM. RF-STEEL Fatigue Members
is preset in the Program / Module list.
You can save the settings as a user profile to reuse them in other models. These functions are
described in Chapter 11.1.3 of the RFEM manual.
41
8 General Functions 8
Before the modified cross-sections are transferred to RFEM, a security query appears as to whether
the results of RFEM should be deleted. By confirming the query and starting the [Calculation] in
the RF-STEEL Fatigue Members module, the RFEM internal forces as well as the design ratios will
be determined in one single calculation run.
If the modified cross-sections have not been exported to RFEM yet, you can reimport the original
cross-sections in the design module by using the options shown in Figure 8.10. Please note,
however, that this option is only available in the 1.2 Materials window.
Clipboard
To copy cells selected in the result windows to the Clipboard, use the keys [Ctrl]+[C]. Press [Ctrl]+[V]
to insert the cells, for example in a word processing program. The headers of the table columns
will not be transferred.
Printout report
You can print the data of RF-STEEL Fatigue Members in the global printout report (see Chapter 7.1,
page 35) to export them subsequently. Then, in the printout report, click
File → Export to RTF.
The function is described in the RFEM manual, Chapter 10.1.11.
Excel / OpenOffice
RF-STEEL Fatigue Members provides a function for directly exporting data to MS Excel, OpenOf-
fice.org Calc, or the CSV file format. To open the corresponding dialog box, click
File → Export Tables.
The following export dialog box appears:
42
8 General Functions 8
When you have selected the relevant options, you can start the export by clicking [OK]. Excel or
OpenOffice will be started automatically, you do not need to open the programs first.
43
9 Example: Tubular Truss 9
9 Example: Tubular Truss
In the following example from [2], we examine a 36 m long ceiling beam of a machine hall formed
as a planar truss. The beam is to be variably stressed by machine loads. These loads represent
the upper loads, that means the loading varies between zero and the maximum value. The result
is a constant stress range corresponding to the magnitude of the represented loads.
Cross-Sections
Top chord: RO 219.1x7.1 (DIN EN 10220)
Struts: RO 88.9x4 (DIN EN 10220)
Bottom chord: RO 177.8x7.1 (DIN EN 10220)
Material
Structural steel S 235 (EN 10025-2:2004-11)
44
9 Example: Tubular Truss 9
Determination of Member Loading
The beam is modeled with continuous chords and flexibly connected struts. The calculation
of the structure provides the following normal forces and bending moments for the members
on Node 6.
The internal forces can be presented as a load combination consisting of two load cases:
Load case 1: Normal forces in equilibrium
Load case 2: Remaining internal forces in chord (normal forces and bending)
45
9 Example: Tubular Truss 9
Nominal Stress Range of Critical Components
As pictured in Figure 9.3, the governing stress is in Chord 1, since there is the major tension force.
Only Strut 2 of both diagonals is subjected to the tension force.
Load case 1: Normal forces in equilibrium
17.2
𝜎𝑏,𝑎𝑥 = ⋅ 103 = 16.07 N/mm2
1070
Load case 2: Remaining internal forces in chord
228.50 0.786 ⋅ 10 6
𝜎𝑐 ℎ,𝑐 ℎ = ⋅ 103 − = 55.0 N/mm2
3807 0.156 ⋅ 10 6
Bending moments in the chord reduce the tension force of the chord on the side where the struts
are connected.
In order to consider the actions of secondary bending moments, the nominal stress range must be
multiplied by the increase factors k1 according to [1], Tab 4.1. A factor of 1.3 applies for the stuts
and a factor of 1.5 for the chords.
Load case 1: Normal forces in equilibrium
𝜎𝑏,𝑎𝑥 = 1.3 ⋅ 16.07 = 20.90 N/mm 2
Load case 2: Remaining internal forces in chord
𝜎𝑐 ℎ,𝑐 ℎ = 1.5 ⋅ 55.0 = 82.50 N/mm2
The damage equivalent factor 𝜆 is obtained from the general formula as:
1 1
1 𝑛
𝛥𝜎𝑐 ℎ,𝑐 ℎ 𝑚 u�
1 𝑛
83 5 5
46
9 Example: Tubular Truss 9
9.2 Design in RF-STEEL Fatigue Members
9.2.1 Definition of Detail Category
Similarly to the failure graphic of the detail category 45 in [1], Tab. 8.7, the governing design area
is the upper area of the bottom chord member (Chord 1). The design-relevant stress points are
implemented for each cross-section in the cross-section library. In our example, tubular stress
points 8 to 12 are relevant for the design. You can assign the corresponding detail category
for these stress points in the 1.4 Design Categories window.
In Window 1.4, you can also define the damage equivalent factor for the bottom chord member.
Due to preliminary considerations with the determination of the maximum load cycle as well as
retroactive calculation of the respective damage equivalent factors, the design ratio is set to 100 %
in RF-STEEL Fatigue Members.
47
9 Example: Tubular Truss 9
Figure 9.6: Window 2.1 Design by Cross-Section - Limitation of direct stress range
Check:
82.93
= 0.24 ≤ 1.00
352.5
The serviceability limit state design is thus fulfilled.
48
9 Example: Tubular Truss 9
9.2.3 Design of Nominal Direct Stress Range
For the design of nominal direct stress range according to [1], Clause 8(2), the design ratio is
set to 100%.
Figure 9.7: Window 2.1 Design by Cross-Section - Design for nominal direct stress range
Direct stresses
𝛾𝐹 𝑓 ⋅ 𝛥𝜎𝐸 ,2 = 𝜆 ⋅ 𝛥𝜎
𝛾𝐹 𝑓 ⋅ 𝛥𝜎𝐸 ,2 = 0.471 ⋅ 82.93
𝛾𝐹 𝑓 ⋅ 𝛥𝜎𝐸 ,2 = 38.977 N/mm2
Check:
𝛾𝐹 𝑓 ⋅ 𝛥𝜎𝐸 ,2
≤ 1.00
𝛥𝜎𝐶 /𝛾𝑀 𝑓
38.977
≤ 1.00
45/1.15
1.00 ≤ 1.00
49
A Literature A
Literature
[1] EN 1993-1-9: Bemessung und Konstruktion von Stahlbauten Teil 1-9: Ermüdung. Beuth Verlag
GmbH, Berlin, 2005.
[2] Grundlagen und Erläuterung der neuen Ermüdungsnachweise nach Eurocode 3. Nussbaumer
A., Günther H.-P., Stahlbau-Kalender, Ernst & Sohn, Berlin, 2006.
50
B Index B
Index
B H
Background graphic . . . . . . . . . . . . . . . . . . . . 30 Hidden result diagram . . . . . . . . . . . . . . . . . . 33
Bottom stress . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 I
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
C Internal forces . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Calculation start . . . . . . . . . . . . . . . . . . . . . . . . 21
Clipboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 L
Color bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Color scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Load case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Comment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Load combination . . . . . . . . . . . . . . . . . . . . . . 11
Consequence of failure . . . . . . . . . . . . . . . . 6, 19 Location x . . . . . . . . . . . . . . . . . . . . . . . . . . 23, 26
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Cross-section . . . . . . . . . . . . . . . . . . . . . . . 14, 38 M
Cross-section graphic . . . . . . . . . . . . . . . . . . . 16 Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 41
Cross-section library . . . . . . . . . . . . . . . . . . . . 14 Material description . . . . . . . . . . . . . . . . . . . . . 12
Cross-section optimization . . . . . . . . . . . . . . . 38 Material library . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cross-section properties . . . . . . . . . . . . . . . . . 17 Material properties . . . . . . . . . . . . . . . . . . . . . 12
Member . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 25
D
Damage equivalent factor . . . . . . . . . 6, 7, 9, 18 N
Damage tolerant . . . . . . . . . . . . . . . . . . . . . . . 19 Navigator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Decimal places . . . . . . . . . . . . . . . . . . . . . . 12, 41 Nominal stress . . . . . . . . . . . . . . . . . . . . . . . . . 18
Design . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 22, 25 Normal stress range . . . . . . . . . . . . . . . . . . . . . . 7
Design case . . . . . . . . . . . . . . . . . . . . . . . . . 30, 37
Design ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 O
Detail category . . . . . . . . . . . . . . . . . . . . . . . . . 18 Open RF-STEEL Fatigue Members . . . . . . . . . . 4
Detail settings . . . . . . . . . . . . . . . . . . . . . . . . . . 19 OpenOffice . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Display navigator . . . . . . . . . . . . . . . . . . . . 30, 33 Optimization . . . . . . . . . . . . . . . . . . . . 15, 38, 39
E P
Excel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 31, 33
Exit RF-STEEL EC3 . . . . . . . . . . . . . . . . . . . . . . . 10 Parametrized cross-section . . . . . . . . . . . . . . 39
Export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Exporting cross-section . . . . . . . . . . . . . . . . . 39 Partial safety factor . . . . . . . . . . . . . . . . . . . 6, 19
Exporting material . . . . . . . . . . . . . . . . . . . . . . 41 Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27, 28
Print graphic . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
F Printout report . . . . . . . . . . . . . . . . . . . . . . 35, 36
Fatigue design . . . . . . . . . . . . . . . . . . . . . . . 7, 24 Program start . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Fatigue strength . . . . . . . . . . . . . . . . . . . . . . 6, 18
Favorite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 R
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29, 32 Remark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Filtering members . . . . . . . . . . . . . . . . . . . . . . 33 Result combination . . . . . . . . . . . . . . . . . . . . . 11
Result diagram . . . . . . . . . . . . . . . . . . . . . . 31, 35
G Result display . . . . . . . . . . . . . . . . . . . . . . . . . . 30
General data . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Result values . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Graphic printout . . . . . . . . . . . . . . . . . . . . . . . . 35 Result windows . . . . . . . . . . . . . . . . . . . . . . . . 22
Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Results evaluation . . . . . . . . . . . . . . . . . . . . . . 29
Results navigator . . . . . . . . . . . . . . . . . . . . . . . 30
51
B Index B
RF-DYNAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Top stress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
RFEM graphic . . . . . . . . . . . . . . . . . . . . . . . . . . 35
RFEM work window . . . . . . . . . . . . . . . . . . . . . 29 U
Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 41
S User profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Safe life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Scrolling in windows . . . . . . . . . . . . . . . . . . . . 10 V
Set of members . . . . . . . . . . . . . . . . . . 11, 24, 28 View mode . . . . . . . . . . . . . . . . . . . . . . . . . 29, 30
Shear stress range . . . . . . . . . . . . . . . . . . . . . . . 7 Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Stainless steel . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 11
Stress cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 X
Stress point . . . . . . . . . . . . . . . . . . . . . . 17, 18, 24 x-Location . . . . . . . . . . . . . . . . . . . . . . . . . . 23, 26
Stress range . . . . . . . . . . . . . . . . . . . . 7, 9, 18, 30
Sum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 W
Surface area . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
T
Taper . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 25, 40
52