Professional Documents
Culture Documents
A Phased Approach To Mine Dewatering PDF
A Phased Approach To Mine Dewatering PDF
net/publication/225897566
CITATIONS READS
22 787
2 authors, including:
20 PUBLICATIONS 49 CITATIONS
SEE PROFILE
Some of the authors of this publication are also working on these related projects:
BACK TO BASICS, THE QUEST FOR GOOD HYDROGEOLOGICAL DATA View project
All content following this page was uploaded by Kym Lesley Morton on 10 June 2016.
27
*Kym L Morton
K L M Consulting Services
P 0 Box 119 Lanseria 1748
South Africa
and
**F A van Mekerk
Hydroseal P 0 Box 3245 Randgate 1763
South Africa
ABSTRACT
The construction of an excavation often means penetrating the local or regional water
table. This causes inflows, which if the country rock is significantly permeable can
become at best a nuisance to operations and at worst a hazard. Dry working conditions
are preferable as they reduce wear and tear on machinery, reduce earth moving costs
and often improve slope stability and therefore safety. Options available to mine
management are dewatering, diversion, sealing or a combination of methods. To
achieve the most effective, least cost method it is essential that the origin of the ground
water is determined. The success of a dewatering exercise is directly linked to an
understanding of the ground water regime. Mines cannot afford to use "blanket
methods" when dealing with ground water. It is essential to target the actual inflows
and not divert or seal off water indiscriminately.
The potential impact of ground water inflow to a mine can often be assessed at the pre
feasibility stage. A hydrogeological investigation is best tackled in three phases. The
first phase is a desk study and borehole census and can be initiated by the mine or
quarry developers. The main objective is to determine water levels and regional
hydrogeology. It is very important that the Phase one hydrogeological investigation is
started at the same time as the geological investigation. All exploration drilling records
should include comment on where water was encountered and in what volume.
The objective of Phase two is to indicate at a first level of confidence the probable
impact of mining on the ground water and vice versa. The level of confidence is
determined by the quality of data collected in Phase one. At the end of Phase one
management will be able to assess if water is going to prove a hazard to mining or not.
If it is going to be a hazard then Phase three will be activated. The objective of Phase
three is to plan how to reduce or remove the hazard and either handle or divert the
probable inflows.
Phase three can be accomplished through ma1 dewatering, computer modelling or
through the application of practical experience. The level of sophistication at Phase
three is determined by the potential costs and risks involved.
INTRODUCTION
The development of a mine often means penetrating the local or regional water table.
This causes inflows of ground water, which if the country rock is significantly
permeable, can become at best a nuisance to operations and at worst a hazard. Dry
working conditions are preferable as they reduce wear and tear on machinery, reduce
earth moving costs and often improve slope stability and therefore safety. Wet working
conditions are to be avoided for the following reasons:
o unsafe working conditions
o difficulty in ore handling
o increased explosives cost
o possible slope instability
o reduced operating life of machinery
o nuisance factor
o possible floor heave
This paper describes the steps necessary to plan an effective dewatering system for a
mine. The approach is a phased investigation that builds up a picture of the potential
problem. The phased approach allows gradual expenditure appropriate to the
confidence level required.
PHASE ONE
The potential impact of ground water inflow to a mine can often be assessed at the pre-
feasibility stage. The pre feasibility stage can be designed to include a preliminary
hydrogeological appraisal of the site. An initial appraisal (or Phase one investigation)
can include a desk study and borehole census of the area to determine local and
regional ground water levels. The main objective is to determine the regional
hydrogeology and assess its potential impact on the mine. It is also important to assess
the potential impact of the mine on the ground water.
In areas where ground water is considered a vulnerable resource a national
government's Department of Water Affairs and Forestry or Department of Mines
usually require an impact assessment and assurance that mining activities will not
damage local aquifers or cause excessive pollution of either ground and surface water.
From experience and from a cost point of view it is very important that, if possible, the
Phase one hydrogeological investigation is started at the same time as the geological
investigation. Any exploration drilling records should include comment on where
water was encountered and in what volume. It is not uncommon for a hydrogeologist
to be asked to review the site and be given borehole logs which have no ground water
information on them at all.
One potential mine site in Natal, South Africa had 146 boreholes drilled on it, there
were no records of water strikes and not one borehole had been cased or left open so
no water levels could be measured. To obtain information on the site another 11
boreholes had to be drilled at a cost of R 55 000 (in 1984). This expenditure would
have been totally unnecessary if only some of the boreholes had been correctly logged
for water data.In essence a Phase one investigation is a desk study of all readily
available information without the expense of drilling and test pumping of the aquifer.
The objective of a Phase one study is to determine at a preliminary level if ground
water is likely to prove a significant problem. If the first phase indicated that ground
water would prove to be a problem and therefore incur additional operating costs a
second phase can be initiated. The Phase one study for an operating mine that
encounters ground water inflows would be a borehole census and desk study to
establish a preliminary assessment of the ground water regime for the area ie a fvst
level assessment of the problem using readily available data.
PHASE TWO
The objective of Phase two is to indicate at a higher level of confidence the probable
impact of mining on the ground water and vice versa. The level of confidence is
determined by the quality and quantity of data collected. At the Phase two level
information collected during the desk study would be augmented with new information
collected from a few strategically placed boreholes on and around the proposed site.
Phase two would aim to determine a preliminary estimate of aquifer parameters such as
the volume of ground water in storage, flow characteristics and the dimensions of the
aquifer or aquifers.
Phase two for an operating mine would take into account all information available on
ground water strikes and inflow occurrence. Operating mines can offer a lot of
information on the local aquifer by installing pressure gauges to measure ground water
heads and flow gauges to measure the volume of water made on each level or in
specific sections. Mapping of inflows underground, coupled with structural mapping
of the geology, gives very valuable information for determining the structures which
control the volume and occurrence of inflows. Information essential to the
understanding of the ground water regime at a mine is the regular monitoring of
ground water levels in boreholes sited around the mine and water pressure gauges
located at key positions underground. Phase two would identify the water levels and
pressures which should be monitored by the mine. The amount of monitoring data
required would be determined by the cost implications of ground water inflows and the
amount of data already collected in Phase one. The result of Phase two would be to
estimate the volume of water the mine or quany can expect to encounter over the initial
operating, development years or life of mine.
PHASE THREE
The objective of Phase three is to plan an initial design to divert or dewater the planned
excavation. Once the required information is available Phase three can be accomplished
through computer modelling. Where necessaty a trial dewatering system can be set up.
The application of practical experience throughout phase three is essential to it's
success. The level of sophistication at Phase three is determined by the potential costs
and risks involved. If ground water is shown to be a significant problem there are
basically two ways of dealing with it. The ground water can be either removed or
divened. Ground water that cannot be moved or divened, cost effectively, can be
sealed off from the workings.
o grout injection,
o cover drilling, and
o grouting piling.
The success of a grout curtain of grout injection is dependent on the penetration made
by the grout. It is most effective when diverting ground water that flows along
geological structure. Phalaborwa copper mine and Northam platinum mine are
examples of sites where ground water is diverted by grouting.
Cover drilling and grouting is typically used for underground mining in the
development of new haulages. The problem with diversion underground is that often
inflows are merely delayed and that the diverted water may build up ahead of the
development causing a greater potential hazard. It is therefore important to measure
water pressures and monitor any build up of pressures.
Diversion may be a suitable method for a mine in which the bulk of the ground water
flows through known underground channels. In other cases where the ground water
movement is more diffuse a dewatering and grouting system may be a more effective
option.
The main considerations for ground water diversions at a mine are cost and
effectiveness.
DEWATERING
Dewatering means the removal of ground water from an area through the lowering of
the water table. Methods of removal are:
o wellpoints
o deep boreholes
o dewatering galleries
o drains
o sump pumping
o a combination of some of the above
Wellpoints and boreholes dewater through the principle of pumping interference.As a
borehole is pumped a cone of depression in the water table develops. When pumping
boreholes are placed close to each other the individual cones of depression combine to
produce an interference effect and therefore lower the water table between them more
effectively than if only one borehole was used.
The use of several pumping boreholes increases the effectiveness of this method and
can dewater significant areas. Letlhakane diamond mine in Northern Botswana is one
example of the successful use of this method.
Wellpoints utilise the same principle. They are small diameter screens that can be
driven or jetted into unconsolidated sediments. The water is usually abstracted with a
vacuum pump. The effectiveness of a wellpoint is determined by the permeability of
the material and controlled by atmospheric pressure.
The maximum drawdown which can be achieved is the difference between the suction
head and the static water level. In practice the greatest suction head that can be
developed is about 6,l to 6,7 m. Wellpoint dewatering is therefore used to dewater
near surface saturated sediments. It is often used in combination with deep borehole
dewatering to effectively dewater a multi layered aquifer. Wellpoints have been used to
dewater alluvial aquifers adjacent to some coal mines along the Vaal river channel in
the Northern Free State.
A dewatering gallery can be described as a ring tunnel, often completely encircling the
excavation. This effectively intercepts all ground water flowing towards the quarry or
open pit. The ground water is then pumped to surface. This method was more popular
when the cost of ground breaking was not as high as today.
Drains are a shallow aquifer solution but may be used in combination with deep well
watering to provide a cumulative dewatering effect.
Sump pumping is the most often used method in the low permeability formations
encountered in the bulk of Southern Africa. Very simply, any ground water seeping
into the excavation gravitates to a low point and from there is pumped to surface.
One disadvantage of sump pumping is that the water can become polluted during either
it's travel time in the pit or it's residence time in the sump. A typical example would be
the creation of acid water from water in contact with coal in an open cast mine. The
water then has to be treated prior to disposal at a very high cost.
Another disadvantage is the cost of the power required to lift the water from the lowest
point in the mine or quarry to it's disposal point. Sump pumping, because of a lack of
information on the volumes of water to be moved, is often poorly managed and can
result in unnecessary production losses. However because of the ease of set up often
sump pumping is often the most obvious and cost effective method of dealing with
ground water inflows. In the long run it may often be the most expensive method.
making best use of management and mine engineers. This requires the collation of
important information on the mine or quarry including:
o Dimensions of the area to be dewatered
o Depth to which the water levels must be lowered
o Plans for disposal of the water removed
o Whether the installation will be permanent or temporary
o Quality of the water that has to be removed
Once all the criteria have been assembled a scenario for dewatering can be designed.
The effectiveness of the method chosen can be predicted through the use of a computer
model.
COMPUTER MODELLING
A computer model can be set up to simulate inflows to the excavation over time as the
quarry or mine enlarges. It can also be used to model the effect of say a ring of
dewatering wells. More importantly it can be used to determine the number and depth
of dewatering boreholes or wellpoints or a combination of both needed to draw water
levels down below the planned base of the excavation. Modelling is usually done in
three stages. At stage one the initial model is set up and used to plan the initial
dewatering of the excavation. A trial dewatering system is set up and monitored as the
initial cuts are made. At stage two the model is calibrated with real data and it's
accuracy enhanced. Stage three is the interactive use of the model throughout the life of
the quarry or mine.
The interactive model can be used to predict water levels for subsequent enlargement of
the underground excavation. The basis to the interactive use of the model is the regular
monitoring of water levels and volumes pumped. These figures are used to re calibrate
the model to meet every stage of the mine's life.
The degree of sophistication of the model can range from very simplistic through to a
complete finite element based model which itemises the ground water flow from each
aquifer. The bottom line is cost effectiveness and it's usefulness to planners and
management. Often the most simplistic 'black box' model is all that is required. In
some cases computer modelling is not required but in all cases it is important to
determine a water balance for the operation. One essential part of the water balance is
the ground water flow into the mine or quarry. Only by understanding the source and
volume of flows involved can the ground water be effectively managed.
with any soluble minerals. This requires careful planning of the movement and storage
of water but can be done with additional cost benefits.
CONCLUSION
The dewatering of an excavation is best approached with a phased investigation. The
investigation starts as a low cost exercise to determine if ground water is going to be a
problem or not. If a problem is anticipated the investigation can be advanced to the next
phase. At all times the emphasis is on the cost effectiveness of data collection and the
use of realistic confidence levels. The final phase is the design and implementation of a
dewatering scheme. Where inflows are predicted to be a significant problem computer
modelling is recommended. This will enable management to determine the optimal
method of dewatering and to decide on the most cost effective design.