Professional Documents
Culture Documents
Aerospace: Maintenance Model of Digital Avionics
Aerospace: Maintenance Model of Digital Avionics
Article
Maintenance Model of Digital Avionics
Ahmed Raza
Department of Electronics, National Aviation University, 03058 Kiev, Ukraine; [email protected];
Tel.: +38-044-406-7130
Received: 20 February 2018; Accepted: 29 March 2018; Published: 2 April 2018
Abstract: The cost of avionics maintenance is extremely high for modern aircraft. It can be as high
as 30% of the aircraft maintenance cost. A great impact on the cost of avionics maintenance is
provided by a high level of No Fault Found events (NFF). Intermittent faults are the leading cause
of the NFF appearance in avionics. The NFF rate for avionics systems is between 20% and 50%.
The practice of avionics operation and maintenance confirms the relevance of assessing the impact
of intermittent faults on the maintenance cost and the choice of such option of the maintenance
management, in which the negative impact of the intermittent faults is minimized. In this paper, a
new mathematical model of digital avionics maintenance is developed. Key maintenance effectiveness
indicators are selected. General mathematical expressions are obtained for the average availability,
mean time between unscheduled removals (MTBUR), and expected maintenance cost of single unit
and redundant avionics systems, which are subject to permanent failures and intermittent faults.
The dependence of the maintenance effectiveness indicators on the rate of permanent failures and
intermittent faults is investigated for the case of exponential distribution of time to failures and faults.
The dependence of average availability on the number of spare units in the airline’s warehouse is also
analyzed. On the base of the proposed maintenance model, different options of avionics maintenance
management are considered. Numerical examples illustrate how to reduce the expected maintenance
cost of avionics systems.
Keywords: availability; avionics maintenance; expected cost; intermittent fault; permanent failure;
redundant system
1. Introduction
Modern aircraft use two types of avionics architecture: federated avionics (FA) and integrated
modular avionics (IMA) [1,2]. In FA architecture, each system has a dedicated processing unit, and
the hardware of the processing unit is not used by any other system. Each processing unit is loosely
associated with the processing units of other functions. FA architecture assumes the use of a separate
line replaceable unit (LRU) for each avionics function and interconnection of each LRU with others
via point-to-point data buses such as ARINC 429. One of the drawbacks of FA architecture is that it
is difficult to expand. Any additional LRUs require additional cable communication with existing
LRUs. FA architecture requires long cable runs to connect far located LRUs that increase weight and
can lead to reliability problems [3]. Until the late 1990s, the digital avionics of most civil aircraft,
including the Boeing and Airbus families, was based on the FA architecture principle. The basis of
the IMA is an open network architecture and a single computing platform. At the same time, system
functions are performed by software applications that share common computing resources. In the
IMA, the computing system represents a set of LRMs such as processor modules, memory modules,
network switch modules, power modules etc. The design of LRM is based on a single standard,
ensuring the principle of unification and interchangeability. Compared to the FA architecture, the
transition to the IMA architecture significantly reduces the weight and cost of aircraft equipment.
In the IMA architecture, much of the functionality of a traditional LRU is performed by a special
application. Standalone applications are located in the common IMA modules called core processing
input/output (I/O) modules (CPIOMs). Each CPIOM integrates hardware and software functions and
places them in the same computing and storage resources as well as providing I/O interface to some
conventional avionics LRUs. In order to connect the traditional avionics LRUs, additional LRMs, called
I/O modules, are also included in the IMA architecture. The dialogue between the LRMs is conducted
via avionics data communication networks (ADCN) over the avionics full-duplex switched Ethernet
(AFDX) compliant with the ARINC 664 standard. The IMA architecture connects all LRMs to the ADCN
network, with all information routed to the appropriate LRM through the AFDX switch. The Boeing 777
was the first commercial aircraft with partially introduced IMA architecture. The Boeing 777 uses the
IMA concept to implement only some of the important functions previously performed by independent
LRUs (flight control, communications control, aircraft condition monitoring). In the A380, the IMA
concept was implemented for the most functions [4]. The A380 avionics comprises 30 LRMs and 22
programming functions, which are located in the CPIOMs [5]. The ADCN communications network
comprises 16 AFDX switches and corresponding cables. The switches perform connection of 8 IOMs,
22 CPIOMs, and 50 LRUs with AFDX interface [4,5]. To reduce the number of connections from the
cockpit control panel to avionics cabin computers, the controller area network (CAN) bus is used for
the A380 avionics [6]. Although Airbus began to make extensive use of the CAN bus to reduce cabling
on the A380, the popular ARINC 429 bus is still used to connect the radio control panels in the cockpit
to the avionics LRUs.
Thus, modern avionics includes a large number of the LRMs and LRUs. In turn, each LRU/LRM
consists of several printed circuit board assemblies, which are called shop replaceable units (SRUs).
Modern LRUs and LRMs usually have built-in test equipment (BITE) for continuous monitoring
during flight. In accordance with the design of modern avionics, the following three maintenance
levels are typically considered: organization maintenance level (O-level), intermediate maintenance
level (I-level), and depot maintenance level (D-level). The O-level is a flight-line maintenance where
the LRU/LRM can be removed and replaced for a short period of time. The spare parts at the
O-level are the LRUs/LRMs. Intermediate maintenance is conducted at a dedicated workshop to
repair the removed LRUs/LRMs by replacing the failed SRUs. The spare parts at this maintenance
level are the SRUs. Automated test equipment (ATE) is commonly used at the I-level maintenance.
The failed SRUs are repaired at the D-level maintenance, where the spare parts are non-repairable
electronic components.
Modern avionics systems are redundant systems. Therefore, each LRU/LRM operates up to
a safe failure that is registered by the BITE during flight. The failed LRUs/LRMs are replaced by
spare LRUs/LRMs at the O-level maintenance. This maintenance strategy is called a breakdown
maintenance strategy. In [7] it is stated that “intermittent faults are regarded as the most difficult class
of faults to diagnose and are cited as one of the main root causes of No Fault Found.” Intermittent
faults are mechanical by nature. They occur due to faults of electrical wiring, solder joints, screening
braid, connectors, metal lines of integrated circuits, etc. Modern electronic components are reliable,
so the intermittent discontinuity between printed circuit board components is becoming the main
cost driver [8]. Conventional ATE cannot detect intermittent faults that cause NFF for the following
reasons [8,9]:
(1) Monitored object parameters are usually tested only once for a short period of time, which usually
does not coincide with the intermittent fault event time;
(2) Digital averaging, scanning, and sampling of the test signal miss out intermittent faults;
(3) The removed LRUs/LRMs are tested in the laboratory rather than in the operating environment
where faults occur; the electrical wiring interconnect system is also tested in a static environment;
(4) Conventional ATE are designed to detect permanent failures, faulty components, as well as short
circuits and breaks in electrical circuits, and are not capable of intermittent fault diagnostics;
(5) Intermittent faults that cause NFF do not correspond to any certain failure pattern.
Aerospace 2018, 5, 38 3 of 16
The breakdown maintenance strategy may be inefficient at a high incidence of the NFF events
because traditional ATE cannot detect intermittent faults and the same intermittent fault may occur
again on the next flight. As indicated in [10], the estimated level of NFF for avionics is from 20% to
50%, and, moreover, avionics components account for 80.4% of all unconfirmed failures, which, in
addition, leads to 26.6% of unscheduled removals of avionics LRUs/LRMs [11]. The main reason for
unconfirmed failures of electronic LRUs/LRMs is the occurrence of intermittent faults in flight [12].
The negative impact of unconfirmed failures on airline operations includes increased service time,
disruption of flight regularity, and an increase in spare LRUs and LRMs, which ultimately leads to
an increase in the life cycle cost of avionics systems. Thus, the operational practices in commercial
aviation confirm the relevance of assessing the impact of intermittent faults on the life cycle costs of
avionics systems as well as the option of selecting a maintenance organization that minimizes the
negative impact of intermittent faults.
The growing interest in assessing the cost of avionics maintenance is manifested in a large
number of publications on this topic. A stochastic model evaluating the lifecycle cost associated
with the application of prognostic health management (PHM) to helicopter avionics was considered
in [13]. However, the impact of intermittent faults on the lifecycle cost of helicopter avionics was not
assessed in this model. Mathematical model of a periodically monitored avionic LRU was considered
in [14]. Equations of availability and expected maintenance costs of redundant avionics systems were
derived. However, this model cannot be applied to modern avionics systems, which are continuously
monitored. And, moreover, the proposed model does not consider the impact of intermittent faults
on the maintenance effectiveness indicators. Avionics hardware lifecycle cost model was proposed
in [15]. The model considered such drivers of the life-cycle costs as type of technology, percentage of
new designs, weight, volume, design reliability, and operational reliability in respect to permanent
failures. Intermittent faults were not included into the model. Different maintenance strategies related
to the presence of NFF were considered in [16]. Statistics on NFF is analyzed, according to which
the percentage of NFF in military avionics is about 70%. The proposed cost equations are empirical
and can only be used for a given percentage distribution of the confirmed and unconfirmed failures.
The structural-logical model of the main cost drivers of the total cost of NFF consequences was
considered in [17]. The conducted analysis shows how the most suitable drivers can be selected to
represent aggregate costs due to NFF. This article shows the relevance of the task of quantifying the
cost of the NFF effects, but it does not contain mathematical or other models to solve this problem.
A maintenance model of a continuously tested single-unit digital system subject to revealed and
unrevealed failures, and intermittent faults was considered in [18]. The derived availability expression
is valid only for the systems with continuous operation. Avionics systems are operated with alternation
of flights and landings. Therefore, the proposed mathematical model cannot be used to estimate the
availability of avionics systems. An empirical model to estimate the unit cost per hour depending on
the total flight time, aircraft size, load factor, average flight time, exchange rate, number of passengers
per airline, and gross domestic production was proposed in [19]. The proposed cost equation is purely
economic in nature and cannot be used to select the optimal option of avionics maintenance.
The following references do not relate to mathematical models of avionics maintenance, which
are the subject of this study. However, these references are important to understand the proposed
mathematical model for assessing the operational reliability of avionics LRUs/LRMs. The strategy of
detection of intermittent faults is analyzed, in which testing is carried out at regular intervals in [20].
An exponential time distribution to a permanent failure and intermittent fault is assumed. The optimal
testing frequency is determined, which maximizes the probability of detecting an intermittent fault
upon its first appearance. This model is not suitable for assessing the operational reliability because
avionics systems are monitored continuously in flight, rather than periodically. A Markov model of
general-purpose reliability with three states for fault-tolerant systems with both permanent failures and
intermittent faults was considered in [21]. A comparison is made between the reliability of the duplex
and redundant systems in the presence of permanent failures and intermittent faults. The proposed
Aerospace 2018, 5, 38 4 of 16
model can only be used for the systems with continuous operation. A reliability model for determining
the optimal frequency of testing intermittent faults in the built-in pipelined processor by the criterion
of the minimum cost of testing was considered in [22]. The Markov model with continuous time and
two states is used for probabilistic modeling of intermittent faults. This model can be used only for the
systems with periodic testing of the state, operating in continuous mode. A model for studying the
reliability of digital systems subject to both permanent failures and intermittent faults was considered
in [23]. The reliability evaluation of a digital system is based on the Markov model containing three
states. This model assumes continuous operation of the digital system, and therefore cannot be used
to assess the operational reliability of avionics systems. The strategy of imperfect checks to detect
intermittent faults in a computer system was investigated in [24]. The system is checked at periodic
times and its fault with a certain probability is detected in the next time of checking. The expected cost
to intermittent fault detection is determined. This model can be used only for systems with periodic
testing and continuous operation. The impact of various scenarios for restoring the processor after
the occurrence of intermittent faults on its performance was assessed in [25]. To achieve this goal, the
operation of a fault-tolerant multi-core processor is simulated in the presence of intermittent faults,
subject to exponential and Weibull distribution. The simulation shows that 40% of the processor
faults are intermittent by nature, and 60% are permanent. The results of this study can be used to
select the distribution law of time to intermittent fault in digital LRUs/LRMs of avionics systems.
Mathematical maintenance models of avionics LRUs subject to permanent failures and intermittent
faults were considered in [26,27]. However, in order to determine the operational reliability indicators
in these models, it is necessary to know the conditional probabilities of occurrence and non-occurrence
of intermittent faults during flight. These probabilities are not easy to derive for an arbitrary probability
distribution function (PDF) of time to intermittent fault.
The aim of this article is to develop a convenient for practical calculations mathematical model
of digital avionics’ operation and maintenance, which allows us to choose the optimal option of
maintenance organization. In this article, mathematical models have been developed to evaluate the
operational reliability of continuously monitored LRUs/LRMs and redundant avionics systems over a
finite time interval, which, unlike known models, take into account the influence of both permanent
failures and intermittent faults.
2. Maintenance Model
This section outlines the step by step development of the avionics LRU/LRM maintenance model.
Applying to (1) the formula of complete mathematical expectation, we determine the mean time
of staying the LRU/LRM in the state ∆1
( )
N (k+
R 1)τ k µτ
E[ T∆1 ] = ∑ ∑ µτ
R
f (z)dz+υ[1 − F (kτ)] ω(υ)dυ+
k =0 kτ µ=1 (µ−1)τ
(2)
R∞
( )
N µτ
∑ µτ
R
f (z)dz+ T [1 − F ( T )] ω(υ)dυ
T µ=1 (µ−1)τ
Let us determine E[ T∆2 ]. If an intermittent fault does not occur till moment kτ and a permanent
failure occurs at the time υ, where kτ < υ ≤ (k + 1)τ, then the conditional mathematical expectation
of the time spent by the LRU/LRM in the state ∆2 is equal to
Z∞
E[ T∆2 |υ ] = [(k + 1)τ − υ] f (z)dz (3)
kτ
Applying to (3) the formula of complete mathematical expectation, we determine the time of
staying the LRU/LRM in the state ∆2
(kZ
+1)τ
N
E[ T∆2 ] = ∑ [1 − F(kτ)](k + 1)τ[Ω((k + 1)τ) − Ω(kτ)] − υω(υ)dυ (4)
k =0
kτ
Aerospace 2018, 5, 38 6 of 16
If the duration of the maintenance operations are constant over the interval (0, T), the mean times
spent by the LRU/LRM in the states ∆3 , ∆5 are determined by the following formulas:
where tO−level is the average duration of maintenance operations at the O-level, tspare is the average
time of waiting the spare LRM/LRU from the warehouse, tstop is the average scheduled stop time
of the aircraft at the airport, and tshipping is the average time of shipping the failed LRM/LRU to the
repair and back.
If an intermittent fault occurs during ν-th flight and until this moment there is no permanent
failure, the conditional mathematical expectation of the time spent by the LRU/LRM in the state ∆6 is
equal to
k (ν+ R 1)τ
∑ f (z)dz, if kτ < υ ≤ (k + 1)τ, k = 0, N
E[ T∆6 |υ ] = t IFR ν=1 (νντ +
(8)
N R 1)τ
∑ f (z)dz, if υ > T
ν=0 ντ
where t IFR is the average time of the LRU/LRM repair due to an intermittent fault.
Applying to (12) the formula of complete mathematical expectation, we get
N
(kZ
+1)τ
k
(νZ+1)τ Z∞ N
(νZ+1)τ
E[ T∆6 ] = t IFR ∑ ∑ f (z)dzω(υ)dυ + ∑ f (z)dzω(υ)dυ (9)
k =0 ν=0 ν=0
ντ T ντ
kτ
If a permanent failure occurs during k-th flight and until moment kτ there is no intermittent fault,
the conditional mathematical expectation of the time spent by the LRU/LRM in the state ∆7 is equal to
R∞
(k+
R 1)τ
t
PFR
f ( z ) dz ω(υ)dυ, if kτ < υ ≤ (k + 1)τ, k = 0, N
E[ T∆7 |υ ] = kτ kτ (10)
t PFR [1 − F ( T )], if υ > T
where t PFR is the average time of the LRU/LRM repair due to a permanent failure.
Applying to (10) the formula of complete mathematical expectation gives
( )
N
E[ T∆7 ] = t PFR ∑ [1 − F(kτ)][Ω((k + 1)τ) − Ω(kτ)] + [1 − F(T )][1 − Ω(T )] (11)
k =0
Electronic avionics LRUs/LRMs have complex design and include a large number of components.
Extrinsic and intrinsic failure mechanisms of these components may lead the units to failure.
These failure mechanisms can combine together forming a constant failure rate, which is only possible
with an exponential distribution of time to failure [30]. Therefore, as indicated in [31], the exponential
distribution of time to permanent failure can be used for many avionics LRUs. Let ω( x ) = λ exp(−λx )
and f (z) = η exp(−ηz) represent the PDF of time to permanent failure and intermittent fault,
respectively, where λ and η are, respectively, the rate of permanent failures and intermittent faults.
Substituting ω( x ) and f (z) into (2), (4), (9), and (11), we obtain
1 − e−(λ+η)T
E[ T∆2 ] = λτ + e−λτ − 1 (13)
λ 1 − e−(λ+η)τ
1 − e−(λ+η)T
E[ T∆6 ] = t IFR 1 − e−ητ (14)
1 − e−(λ+η)τ
h i
1 − e−(λ+η)T 1 − e−λτ
−(λ+η) T
E[ T∆7 ] = t PFR + e (15)
1 − e−(λ+η)τ
E[ T∆1 ]
AA = (16)
7
∑ E T∆ j
j =1
Figure 1a,b show a 3D dependence of the average availability on the rate of intermittent faults
and permanent failures under exponential distribution when T = 5000 h, τ = 4 h, tO−level = 0.5 h,
tshipping = 24 h, and E[ T∆4 ] = 0. The difference between plots is that t IFR = 8 h and t PFR = 16 h for
Figure 1a, and t IFR = 80 h and t PFR = 160 h for Figure 1b. As can be seen in Figure 1a,b, availability
decreases with increasing the rate of both permanent failures and intermittent faults. However, the
rate of the permanent failures has slightly greater impact on the average availability than the rate
of the intermittent faults. From Figure 1a follows that the average availability begins to decrease
significantly when η > 3 × 10−4 h−1 . For η < 4 × 10−5 h−1 , the average availability does not depend
on the rate of intermittent faults. The dependence of the average availability on the rate of permanent
failures and intermittent faults in Figure 1b is similar. However, the average availability begins to
decrease significantly when η > 1 × 10−4 h−1 and does not depend on the rate of intermittent faults
for η < 2 × 10−5 h−1 . Thus, intermittent faults have a significant negative impact on the availability of
avionics LRUs/LRMs and this impact becomes stronger when the repair time t IFR is longer.
Figure 1. (a) A 3D plot of the dependence of the line replaceable unit (LRU)/line replaceable module
(LRM) availability on the rates of permanent failures and intermittent faults when t IFR = 8 h and
t PFR = 16 h; (b) A 3D plot of the dependence of the LRU/LRM availability on the rates of permanent
failures and intermittent faults when t IFR = 80 h and t PFR = 160 h.
Modern avionics systems are redundant systems. Usually, active redundancy is used [32]. Using the
method of structural functions [33], it is easy to prove that, for a parallel structure of avionics system with
n identical LRUs/LRMs, the average unavailability is calculated by the following formula:
Equation (17) does not include the mean times of staying the LRU/LRM in the states ∆3 , ∆5 , ∆7
since it is not used in these states on the aircraft board.
For the m-out-of-n structure of the avionics system, the average unavailability is given by
! i n −i
n
n E( T∆1 ) E( T∆1 )
AA = 1 − ∑ i E( T∆1 ) + E( T∆2 ) + E( T∆4 )
1−
E( T∆1 ) + E( T∆2 ) + E( T∆4 )
(18)
i =m
Figure 2a,b show the dependence of unavailability of the duplicated avionics system on the rate of
intermittent faults (a) and permanent failures (b) for T = 10, 000 h, τ = 5 h, and E[ T∆4 ] = 1 h. As can
be seen from the comparison of Figure 2a,b, the rate of permanent failures has a greater impact on the
unavailability than the rate of the intermittent faults. It should be also noted that the unavailability
begins to increase significantly when η > 2 × 10−4 h−1 .
Figure 3a shows the dependence of unavailability of the duplicated avionics system on the number
of spare LRUs/LRMs (r) in the airline’s warehouse for the case of 20 aircraft when T = 10,000 h, τ = 5 h,
and λ = η = 2 × 10−4 h−1 .
Figure 2. (a) Dependence of unavailability of the duplicated avionics system on the rate of intermittent
faults when λ = 2 × 10−4 h−1 ; (b) Dependence of unavailability of the duplicated avionics system on
the rate of permanent failures when η = 2 × 10−4 h−1 .
Figure 3. (a) Dependence of unavailability of the duplicated avionics system on the number of spare
LRUs/LRMs when λ = η = 2 × 10−4 h−1 ; (b) Dependence of unavailability of the duplicated avionics
system on the number of spare LRUs/LRMs when λ = 2 × 10−4 h−1 and η = 0.
Aerospace 2018, 5, 38 9 of 16
As can be seen from Figure 3a, the unavailability decreases by a factor of 3300 with an increase in
the number of spare LRUs/LRMs from 0 to 5, and at r ≥ 5 the unavailability reaches constant value.
Therefore, any further increase in the number of spare LRUs/LRMs is not practical.
Figure 3b shows the dependence of the unavailability on the number of spare LRUs/LRMs for
the case when the rate of intermittent faults is zero. As can be seen from Figure 3b, with η = 0, the
unavailability reaches a constant value with less number of spare LRUs/LRMs than when η > 0.
Thus, intermittent faults lead to an increase in the number of spare LRUs/LRMs necessary to provide
the required value of the unavailability for the redundant avionics systems.
In Figure 4a,b, 3D plots of the MTBUR dependence on the rates of permanent failures and
intermittent faults are shown for different values of T. As can be seen from Figure 4, MTBUR decreases
when λ and η increase. It should be also noted that MTBUR depends strongly on T for small values of
the rate of permanent failures and intermittent faults. For large values of λ and η, MTBUR almost does
not depend on T.
Aerospace 2018, 5, 38 10 of 16
Figure 4. (a) A 3D plot of the dependence of the mean time between unscheduled removals (MTBUR) on
the rates of permanent failures and intermittent faults when T = 5000 h; (b) A 3D plot of the dependence
of the MTBUR on the rates of permanent failures and intermittent faults when T = 10, 000 h.
where n is the number of identical LRUs/LRMs in the avionics system, M is the number of aircraft
in the airline, Crepair,κ is the average cost of one unscheduled removal of the LRU/LRM and further
repair for the κ-th maintenance option, NR ( T ) is the mathematical expectation of the LRU/LRM
removals in the interval (0, T), and CEκ is the capital expenditures required to organize the κ-th
maintenance option.
The mathematical expectation of the LRU/LRM removals in the interval (0, T) can be expressed
through the MTBUR and T as follows:
Let us consider possible maintenance options during the post warranty period. Small or budget
airlines may not have enough money to organize O-, I- and D-level maintenance. Therefore, some
of these airlines may use only O-level maintenance. In this case κ = 1 and cost function Crepair,1 is
given by
Crepair,1 = CO-level + Coutsourcing + Cshipping,LRU (24)
where CO-level is the average cost of the O-level maintenance, Coutsourcing is the average cost of repairing
the LRU/LRM outside the airline, i.e., in a repair station or at the manufacturer, Cshipping,LRU is the
average cost of shipping the LRU/LRM to the repair and back to the warehouse.
For this option of maintenance, capital expenditures CE1 include only the cost of spare
LRUs/LRMs used in the O-level maintenance. Therefore,
where S LRU is the number of spare LRUs/LRMs in the airline warehouse and CLRU is the cost of one
spare LRU/LRM.
Let us now consider the second (κ = 2) maintenance option, which includes O- and I-Level
maintenance. The third maintenance level is outsourced. At the I-level maintenance ATE is usually
used to test the suspicious LRUs/LRMs and detect the faulty SRUs. Traditional ATE cannot diagnose
intermittent faults in dismantled LRUs/LRMs for a variety of reasons [9]. Intermittent faults registered
on-board cannot be confirmed by ATE in this maintenance option. Therefore, only SRUs with
Aerospace 2018, 5, 38 11 of 16
permanent failures are shipped to the manufacturer or repair station for repairing. The spare parts in
this maintenance option are LRUs/LRMs and SRUs.
The average repair cost of the LRU/LRM for the κ = 2 maintenance option is determined
as follows:
A
Crepair,2 = CO-level + C I-level + Cshipping,SRU + Crepair,SRU PPF (26)
where C I-level is the average cost of I-level maintenance, Cshipping,SRU is the average cost of shipping the
SRU to the place of repair and back to the airline warehouse, Crepair,SRU is the average cost of the SRU
repair at the manufacturer or repair station, and PPF A is the a posteriori probability that the dismantled
Capital expenditures CE2 include the cost of spare LRUs/LRMs used in the O-level maintenance,
the cost of spare SRUs used in the I-level maintenance, and the relative cost of ATE, i.e.,
L
CE2 = S LRU CLRU + ∑ Cl χl + CATE /W (29)
l =1
where Cl is the cost of the l-th l = 1, L type of spare SRU, χl is the number of spare SRUs of the l-th
type, C ATE is the cost of ATE, which is used at the I-level, and W is the number of different LRUs/LRMs
that ATE can test at the I-level.
Let us consider one of the possible options to implement a three-level maintenance system,
including O-, I-, and D-levels. As already noted, maintenance at the D-level is carried out in the
specialized repair shops equipped with diagnostic tools capable of detecting a failed non-recoverable
electronic component or a group of components in the SRU that is rejected at the I-level. The spare
parts at this maintenance level are assemblies and electronic components. Due to the disadvantages
of traditional ATE in detecting intermittent faults, specialized intermittent fault detector (IFD) and
intermittent fault detection and isolation system (IFDIS) have recently been developed [35,36]. IFD and
IFDS can be used as in the I-level as well as in the D-level maintenance.
The average repair cost of the LRU/LRM for the κ = 3 maintenance option is determined
as follows:
PF PF A IF IF A
Crepair,3 = CO-level + CI-level + CD-level PPF + CI-level + CD-level PIF (30)
PF
where C I-level IF
and C I-level are, respectively, the average cost of the I-level maintenance for an LRU/LRM
with a permanent failure and intermittent fault, CD-levelPF IF
and CD-level are, respectively, the average cost
of the D-level maintenance for an SRU with a permanent failure and intermittent fault.
Capital expenditures CE3 include the cost of spare LRUs/LRMs used in the O-level, the cost of
spare SRUs used in the I-level, the cost of spare assemblies and electronic components used in the
D-level, the relative cost of ATE used in the I-level, the relative cost of IFD used in the I- and D-level,
and the cost of repair tools used in the D-level maintenance. So,
L
∑ l l D-level
spares R
CE3 = S LRU CLRU + C χ + C + C ATE + C IFD + C D-level /W (31)
l =1
spares R
where CD-level is the cost of spare parts in the D-level maintenance, C IFD is the cost of IFD, and CD-level
is the cost of repair tools used in the D-level maintenance.
Aerospace 2018, 5, 38 12 of 16
3. Results
In this section, we consider an example of using the mathematical model developed in Section 2
to choose the best maintenance option for a redundant avionics system.
Let us calculate the ETMC for the air data inertial reference system (ADIRS). The ADIRS provides
traffic data (airspeed, angle of attack and altitude) and information on inertial control (position and
altitude) on the displays to pilots, as well as to other aircraft systems such as engines, autopilot, flight
control system and chassis. The ADIRS consists of n = 3 fault-tolerant air data inertial reference units
(ADIRUs) located in the aircraft electronics rack. Typical ADIRU comprises the following SRUs: an air
data computer, multimode receiver, 3 digital ring laser gyros, 3 quartz accelerometers, and power
supply module.
The following data are used in calculation of the ETMC for different maintenance options:
T = 50,000 h, M = 97, τ = 8 h, λ = 2.5 × 10−5 h−1 , η = 1.76 × 10−5 h−1 , CLRU = 50,000$,
CO-level = 20$, Coutsourcing = 7500$, Cshipping,LRU = 300$, C I-level = 30$, Cshipping,SRU = 100$,
PF
Crepair,SRU = 1000$, L = 9, Cl = 5000$ l = 1, 9 , C ATE = 2,000,000$, W = 120, C I-level = 15$,
IF PF IF spares
C I-level = 25$, CD-level = 40$, CD-level = 60$, C IFD = 100,000$, CD-level = 30,000$, and
R
CD-level = 200,000$.
The results of calculation are shown in Table 1. Since in the third option of maintenance the IFD is
used, the rate of intermittent faults in repaired ADIRUs should be significantly reduced. As described
in [37], after repairing the AN/APG-68 airborne radar of the F-16 using IFDIS, MTBUR increased more
than threefold. Therefore, it was assumed in the calculations that for the third maintenance option, the
rate of intermittent faults is 3 times less, i.e., η = 0.6 × 10−5 h−1 . To determine the optimal number
of spare ADIRUs, a mathematical model for the operation of the warehouse of spare LRUs based on
Markov chains with continuous time was developed. The optimum number of spare LRUs ensured
the absence of delays in scheduled flights of aircraft.
Table 1. Calculation results for three options of air data inertial reference system (ADIRS) maintenance.
The number of spare SRUs χl l = 1, 9 was calculated for confidence probability of 0.99 for each
type of SRU. According to the calculations, in the second maintenance option there should be two
spare SRUs of each type in the warehouse, and in the second maintenance option only one spare SRU.
As can be seen from Table 1, the third maintenance option, which uses IFD at the I- and D-level
maintenance, has the lowest maintenance cost and is therefore the best. Indeed, the maintenance cost
in the third maintenance option is 8.3 times smaller than in the first option and more than 3.5 times
smaller than for the second option.
It should also be noted that the unavailability of ADIRS is the same for all maintenance options.
This means that unavailability (or availability) of the redundant avionics systems cannot be used to
select the best maintenance option of avionics systems because it does not depend on the characteristics
of the I- and D-level maintenance.
The results of Table 1 convincingly show the preference of using the third maintenance option in
airlines. The question of the stability of the obtained results to the change in the rate of intermittent
faults is also topical. Figure 5 shows the dependence of ETMC on the rate of intermittent faults for each
maintenance option. As can be seen in Figure 5, the first maintenance option is very sensitive to the
rate of intermittent faults, since EMTC is increased from $4.23 × 106 to $118 × 106 (i.e., almost 28 times
increase) when η is changed from 10−6 h−1 to 10−3 h−1 . However, when using the third maintenance
option and the same change in the rate of intermittent faults, the ETMC increases from $1.83 × 105 to
Aerospace 2018, 5, 38 13 of 16
$7.3 × 105 , i.e., only four times increase. The second maintenance option also has the stability to the
change of the intermittent fault rate, however, when using it, the ETMC is 2–3 times greater than in the
third option.
Figure 6 shows the dependence of the optimal number of spare ADIRUs on the rate of intermittent
faults for the first, second, and third maintenance options.
Figure 5. Expected total maintenance cost as a function of the intermittent fault rate for the first
maintenance option (black squares), second maintenance option (blue rhombus), and third maintenance
option (red circles).
Figure 6. Optimal number of spare ADIRUs as a function of the intermittent fault rate for the first
maintenance option (black squares), second maintenance option (blue rhombus), and third maintenance
option (red circles).
As can be seen from Figure 6, first, to ensure the regularity of flights, a significantly larger number
of spare ADIRUs is required for the first maintenance option compared to the second and third options
and, second, the optimal number of spare ADIRUs is very strongly depends on the rate of intermittent
faults for the first maintenance option and weakly depends for the second and third options.
4. Discussion
In this study, a mathematical model has been developed to evaluate the availability and expected
maintenance cost of continuously tested LRMs/LRUs and redundant avionics systems over a finite
interval of time, taking into account the effect of both permanent failures and intermittent faults.
Unlike most published studies, such as [20–25], the developed mathematical model considers the
specifics of the architecture and application of modern avionics systems and can be used for any law
of distribution of the operating time to permanent failure and intermittent fault. The described model
Aerospace 2018, 5, 38 14 of 16
might be further developed in order to divide the NFF events to intermittent faults and false alarms
of the BITE. The need for separate consideration of false alarms is due to the fact that the level of
false alarms is high enough in the aviation industry, reaching 28% of all events associated with alarm
signals [38].
A number of publications point to the topical need for a cost assessment of the consequences of
NFF events in electronic systems [12,17]. This problem is indeed topical because according to [39],
the average cost of losses due to NFF per aircraft in the US civil aviation was about $200,000 in 2013.
Similar losses exist in military aviation [40,41]. So, according to the US Department of Defense, three
out of four (75%) weapon systems are subject to NFF-type failures [41]. NFF costs the US Department
of Defense $2 billion to $10 billion in losses per year [8]. As indicated in [8,9], the main cause of NFF
events are the intermittent faults that occur in flight. Therefore, the developed mathematical model
for evaluating the average cost of avionics systems maintenance with taking into account the effect
of intermittent faults is of undoubted interest for developers of maintenance programs for avionics
systems of civil and military aircraft. The proposed cost model allows not only to assess the impact of
intermittent faults, but also to choose the maintenance option that is practically independent on the
rate of intermittent faults, thus ensuring the minimum cost of maintenance. The ideas in this paper are
illustrated by an example that describes three maintenance options for the redundant avionics system
ADIRS. Among these maintenance options, the option of a three-level maintenance with IFD at the
second and third maintenance levels is of particular interest. Despite additional capital expenditures,
this option provides the lowest average maintenance cost, which is 8.3 times less than in a single-level
and 3.5 times less than in a two-level maintenance system without using IFD. This result is explained
by the fact that the application of the IFD allows the identification of SRUs with intermittent faults at
the I-level maintenance and, subsequently, at the D-level maintenance to eliminate the causes of such
faults. At the same time the rate of intermittent faults decreases and, hence, the MTBUR increases.
The performed calculations fully confirm the statistical data given in [37].
Future research directions may include the development of cost models for maintenance options
with different combinations of O-, I-, and D-levels of maintenance with the involvement of outsourcing
service companies.
5. Conclusions
This study has focused on developing a maintenance model of digital avionics systems.
The proposed mathematical model can be used for both federated and integrated modular avionics
architecture of modern aircraft. The derived analytical expressions for the calculation of the availability,
MTBUR and expected total maintenance cost can be used for any law of time distribution to permanent
failure and intermittent fault, including both cases of sudden failures and faults and cases of gradual
failures and faults, which are typical for deteriorating systems. Since many avionics systems have an
exponential time-to-failure distribution, the mathematical expressions have been derived to calculate
the mean times spent by the LRU/LRM in different operation and maintenance states for the case
of an exponential distribution of the operating time to permanent failure and intermittent fault.
On illustrative numerical examples it has been shown that the average availability of the LRU/LRM
and redundant avionics system begins to decrease significantly when the rate of intermittent faults is
greater than 1 × 10−4 h−1 and MTBUR decreases five times with increasing the rate of intermittent
faults from 10−5 to 5 × 10−4 h−1 . It has also been shown that the presence of the intermittent faults
increases the number of spare LRUs/LRMs required to ensure the regularity of flights. Thus, numerical
results obtained on the basis of the proposed maintenance model confirm statistical data on the
consequences of unconfirmed failures [10–12]. The generalized equations have been developed to
calculate the expected total maintenance cost during finite horizon of operation for three alternative
maintenance options that differ by existence of I- and D-levels of maintenance; the numerical example
shows that a three-level post-warranty maintenance system is optimal for the selected source data,
since it results in a minimum number of spare LRUs and SRUs, as well as minimum operating costs
Aerospace 2018, 5, 38 15 of 16
being 8.3 times less than for a single-level system and 3.5 times less than in a two-level maintenance
system. The practical significance of the obtained results is that the proposed maintenance models
allow one to compare the various options for organizing the maintenance of avionics and to choose
the option that provides the lowest cost of maintenance. As shown by numerical calculations, the cost
of different maintenance options can differ by several times, which cannot be predicted in the absence
of the proposed mathematical models.
References
1. Bieber, P.; Boniol, F.; Boyer, M. New challenges for future avionic architectures. AerospaceLab 2012, 4, 1–10.
2. Gaska, T.; Watkin, C.; Chen, Y. Integrated modular avionics—Past, present, and future. IEEE Aerosp. Electron.
Syst. Mag. 2015, 30, 12–23. [CrossRef]
3. Alena, R.L.; Ossenfort, J.; Laws, K.I. Communications for integrated modular avionics. In Proceedings of the
2007 IEEE Aerospace Conference, Big Sky, MT, USA, 3–10 March 2007.
4. Module 11.19 integrated modular avionics (ATA 42). AFAQ Inst. Aviat. Technol. 2012, 2, 1–64.
5. A380 Technical Training Manual. LEVEL I—ATA 42 Integrated Modular Avionics & Avionics Data Communication
Network; Airbus: Toulouse, France, 2006; pp. 1–20.
6. ARINC Specification 825: General Standardization of CAN (Controller Area Network) Bus Protocol for
Airborne Use. Available online: http://www.arinc-825.com/arinc825-standard (accessed on 1 July 2015).
7. Syed, W.A.; Khan, S.; Phillips, P.; Perinpanayagam, S. Intermittent fault finding strategies. Procedia CIRP
2013, 11, 74–79. [CrossRef]
8. Anderson, K. Intermittent Fault Detection and Isolation Reduces NFF and Enables Cost Effective
Readiness. Available online: http://www.ncms.org/wp-content/uploads/3-Steadman-CTMA-Briefing-
2017.pdf (accessed on 4 April 2017).
9. Steadman, B.; Berghout, F.; Olsen, N. Intermittent fault detection and isolation system. In Proceedings of the
2008 IEEE AUTOTESCON, Salt Lake City, UT, USA, 8–11 September 2008; pp. 37–40.
10. Soderholm, P. A system view of the no fault found (NFF) phenomenon. Reliab. Eng. Syst. Saf. 2007, 92, 1–14.
[CrossRef]
11. Hockley, C.; Phillips, P. The impact of no fault found on through-life engineering services. J. Qual. Maint. Eng.
2012, 18, 141–153. [CrossRef]
12. Khan, S.; Phillips, P.; Jennions, I.; Hockley, C. No Fault Found events in maintenance engineering Part 1:
Current trends, implications and organizational practices. Reliab. Eng. Syst. Saf. 2014, 123, 183–195. [CrossRef]
13. Sandborn, P.; Feldman, K.L.; Ghelam, S. Life cycle cost impact of using prognostic health management
(PHM) for helicopter avionics. Microelectron. Reliab. 2007, 47, 1857–1864.
14. Ulansky, V.V.; Machalin, I.A. Optimization of post warranty maintenance of avionics systems. In Proceedings
of the 2007 International Conference on Aeronautical Science and Air Transportation (ICASAT2007), Tripoli,
Libya, 23–25 April 2007; pp. 619–628.
15. Curry, E.E. FALCCM-H: Functional avionics life cycle model for hardware. In Proceedings of the 1993
IEEE National Aerospace and Electronics Conference (NAECON 1993), Dayton, OH, USA, 24–28 May 1993;
Volume 2, pp. 950–953.
16. Ilarslan, M.; Ungar, L.Y.; Ilarslan, K. An economic analysis of false alarms and no fault found events in air
vehicles. In Proceedings of the 2016 IEEE AUTOTESTCON, Anaheim, CA, USA, 12–15 September 2016;
pp. 1–7.
17. Erkoyuncu, J.A.; Khan, S.; Hussain, S.M.; Roy, R. A framework to estimate the cost of no-fault found events.
Int. J. Prod. Econ. 2016, 173, 207–222. [CrossRef]
18. Ulansky, V.; Terentyeva, I. Availability modeling of a digital electronic system with intermittent failures and
continuous testing. Eng. Lett. 2017, 25, 104–111.
19. Vega, D.J.G.; Pamplona, D.A.; Oliveira, A.V.M. Assessing the influence of the scale of operations on
maintenance costs in the airline industry. J. Trans. Lit. 2016, 10, 10–14. [CrossRef]
20. Nakagava, T. Maintenance Theory of Reliability; Springer: London, UK, 2005; pp. 220–224.
Aerospace 2018, 5, 38 16 of 16
21. Hsu, Y.T.; Hsu, C.F. Novel model of intermittent faults for reliability and safety measures in long-life
computer systems. Int. J. Electron. 1991, 71, 917–937. [CrossRef]
22. Kranitis, N.; Merentitis, A.; Laoutaris, N. Optimal periodic testing of intermittent faults in embedded pipeline
processor applications. In Proceedings of the 2006 Design, Automation and Test in Europe Conference,
Munich, Germany, 6–10 March 2006; pp. 65–70.
23. Prasad, V.B. Digital systems with intermittent faults and Markovian models. In Proceedings of the 1992 IEEE
35th Midwest Symposium on Circuits and Systems, Washington, DC, USA, 9–12 August 1992; pp. 195–198.
24. Zhao, X.; Chen, M.; Nakagawa, T. Optimal time and random inspection policies for computer systems.
Appl. Math. Inf. Sci. 2014, 8, 413–417.
25. Rashid, L.; Pattabiraman, K.; Gopalakrishnan, S. Intermittent hardware errors recovery: Modeling and
evaluation. In Proceedings of the 2012 Ninth International Conference on Quantitative Evaluation of Systems
(QEST), London, UK, 17–20 September 2012; pp. 1–10. [CrossRef]
26. Raza, A.; Ulansky, V. Assessing the impact of intermittent failures on the cost of digital avionics’ maintenance.
In Proceedings of the 2016 IEEE Aerospace Conference, Big Sky, MT, USA, 5–12 March 2016; pp. 1–16.
27. Raza, A.; Ulansky, V. Minimizing total lifecycle expected costs of digital avionics’ maintenance. Procedia CIRP
2015, 38, 118–123. [CrossRef]
28. MIL-HDBK-338B. In Military Handbook; Electronic Reliability Design Handbook; Department of Defense:
Arlington County, VA, USA, 1998; pp. 5.72–5.74.
29. Elsayed, E.A. Reliability Engineering, 2nd ed.; Wiley: Hoboken, NJ, USA, 2012; pp. 198–206.
30. Drenick, R.F. The failure law of complex equipment. J. Soc. Ind. Appl. Math. 1960, 8, 680–690. [CrossRef]
31. Qin, J.; Huang, B.; Walter, J. Reliability analysis in the commercial aerospace industry. J. Reliab. Anal. Center
2005, 1, 1–5.
32. Yeh, Y.C. Safety critical avionics for the 777 primary flight controls system. In Proceedings of the 2001 IEEE
Digital Avionics Systems Conference (DASC), Daytona Beach, FL, USA, 14–18 October 2001; pp. 1–9.
33. Rausand, M.; Hoyland, A. System Reliability Theory: Models, Statistical Methods, and Applications, 2nd ed.;
Wiley: New York, NY, USA, 2003; pp. 147–152.
34. Kayton, M.; Fried, W.R. Avionics Navigation Systems, 2nd ed.; Wiley: New York, NY, USA, 1997; p. 700.
35. Voyager Intermittent Fault Detector (VIFDT ). Available online: http://www.usynaptics.com/index.php/
products/ncompass-voyager (accessed on 1 January 2017).
36. Intermittent Fault Detection & Isolation System (IFDS). Available online: http://www.usynaptics.com/
index.php/products/ifdis (accessed on 1 January 2017).
37. Anderson, K. IFDIS—Expanding role across the DoD maintenance enterprise. In Proceedings of the 2012
Department of Defense Maintenance Symposium, Grand Rapids, MI, USA, 13–16 November 2012; pp. 1–29.
38. Bliss, J.P. Investigation of alarm-related accidents and incidents in aviation. Int. J. Aviat. Psychol. 2003,
13, 249–268. [CrossRef]
39. NFF—No Fault Found. American Institute of Aeronautics and Astronautics. Available online: https://info.aiaa.
org/tac/AASG/PSTC/Lists/Calendar/Attachments/1/NFF%20Subcommittee.pdf (accessed on 22 April 2013).
40. Hockley, C.; Laceya, L. A research study of no fault found (NFF) in the Royal Air Force. Procedia CIRP 2017,
59, 263–267. [CrossRef]
41. Hockley, C.J.; Lacey, L.; Pelham, J.G. Report for Air Command on the Impact of no Fault Found (NFF) on a Selection
of RAF Aircraft Fleets; Technical Report TES 02-01-2015; EPSRC Through-Life Engineering Services Centre,
Cranfield University: Bedford, UK, 2015.
© 2018 by the author. Licensee MDPI, Basel, Switzerland. This article is an open access
article distributed under the terms and conditions of the Creative Commons Attribution
(CC BY) license (http://creativecommons.org/licenses/by/4.0/).