Professional Documents
Culture Documents
Operating Instructions Micropilot FMR51, FMR52 Hart: Free Space Radar
Operating Instructions Micropilot FMR51, FMR52 Hart: Free Space Radar
Operating Instructions
Micropilot FMR51, FMR52
HART
Free space radar
Order code: XXXXX-XXXXXX
1. Ser. no.: XXXXXXXXXXXX
Ext. ord. cd.: XXX.XXXX.XX
Serial number
3.
A0023555
2 Endress+Hauser
Table of contents
Table of contents
Endress+Hauser 3
Table of contents
13 Maintenance . . . . . . . . . . . . . . . . . . . . . . 82
13.1 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . 82
13.2 Replacing seals . . . . . . . . . . . . . . . . . . . . . . . 82
14 Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
14.1 General information on repairs . . . . . . . . . . . . 83
14.1.1 Repair concept . . . . . . . . . . . . . . . . . 83
4 Endress+Hauser
Micropilot FMR51, FMR52 HART Important document information
1.2 Symbols
Symbol Meaning
DANGER!
DANGER This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING!
WARNING This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION!
CAUTION This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTE!
NOTICE This symbol contains information on procedures and other facts which do not result in
personal injury.
Symbol Meaning
Torx screwdriver
A0013442
A0011220
Endress+Hauser 5
Important document information Micropilot FMR51, FMR52 HART
Symbol Meaning
Cross-head screwdriver
A0011219
Allen key
A0011221
Hexagon wrench
A0011222
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Preferred
Procedures, processes or actions that are preferred.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information.
Reference to documentation
Reference to page
Reference to graphic
, , … Series of steps
Result of a step
Visual inspection
Symbol Meaning
A, B, C, ... Views
Hazardous area
- Indicates a hazardous area.
6 Endress+Hauser
Micropilot FMR51, FMR52 HART Important document information
Symbol Meaning
Safety instructions
Observe the safety instructions contained in the associated Operating Instructions.
Brief Operating Instructions Guide that takes you quickly to the 1st measured value
KA01100F (FMR51/FMR52, The Brief Operating Instructions contain all the essential information
HART) from incoming acceptance to initial commissioning.
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The W@M Device Viewer : Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate
or scan the 2-D matrix code (QR code) on the nameplate.
BB ATEX: II 1/2 G Ex ia IIC T6-T1 Ga/Gb • FMR51 XA00677F XA00677F XA00677F XA00685F -
• FMR52
BC ATEX: II 1/2 G Ex d [ia] IIC T6-T1 Ga/Gb • FMR51 XA00680F XA00680F XA00680F XA00688F XA00680F
• FMR52
BD ATEX: II 1/2/3 G Ex ic [ia Ga] IIC T6-T1 • FMR51 XA00678F XA00678F XA00678F XA00686F XA00678F
Ga/Gb/Gc • FMR52
BL ATEX: II 1/2/3 G Ex nA [ia Ga] IIC T6-T1 • FMR51 XA00678F XA00678F XA00678F XA00686F XA00678F
Ga/Gb/Gc • FMR52
B2 ATEX: II 1/2 G Ex ia IIC T6-T1 Ga/Gb • FMR51 XA00683F XA00683F XA00683F XA00691F -
ATEX: II 1/2 D Ex ia IIIC Txx°C Da/Db • FMR52
Endress+Hauser 7
Important document information Micropilot FMR51, FMR52 HART
B3 ATEX: II 1/2 G Ex d [ia] IIC T6-T1 Ga/Gb • FMR51 XA00684F XA00684F XA00684F XA00692F XA00684F
ATEX: II 1/2 D Ex ta IIIC Txx°C Da/Db • FMR52
B4 ATEX:II 1/2 G Ex ia IIC T6-T1 Ga/Gb • FMR51 XA00681F XA00681F XA00681F XA00689F -
ATEX: II 1/2 G Ex d [ia] IIC T6-T1 Ga/Gb • FMR52
CD CSA C/US DIP Cl.II,III Div.1 Gr.E-G FMR51 XA01113F XA01113F XA01113F XA01115F XA01113F
C2 CSA C/US IS Cl.I,II,III Div.1 Gr.A-G, NI Cl.1 Div. • FMR51 XA01112F XA01112F XA01112F XA01114F -
2, Ex ia • FMR52
C3 CSA C/US XP Cl.I,II,III Div.1 Gr.A-G, NI Cl.1 • FMR51 XA01113F XA01113F XA01113F XA01115F XA01113F
Div.2, Ex d • FMR52
FB FM IS Cl.I,II,III Div.1 Gr.A-G, AEx ia, NI Cl.1 • FMR51 XA01116F XA01116F XA01116F XA01118F -
Div.2 • FMR52
FD FM XP Cl.I,II,III Div.1 Gr.A-G, AEx d, NI Cl.1 • FMR51 XA01117F XA01117F XA01117F XA01119F XA01117F
Div.2 • FMR52
FE FM DIP Cl.II,III Div.1 Gr.E-G FMR51 XA01117F XA01117F XA01117F XA01119F XA01117F
IC IECEx: Ex d [ia] IIC T6-T1 Ga/Gb • FMR51 XA00680F XA00680F XA00680F XA00688F XA00680F
• FMR52
ID IECEx: Ex ic [ia Ga] IIC T6-T1 Ga/Gb/Gc • FMR51 XA00678F XA00678F XA00678F XA00686F XA00678F
• FMR52
IL IECEx: Ex nA [ia Ga] IIC T6-T1 Ga/Gb/Gc • FMR51 XA00678F XA00678F XA00678F XA00686F XA00678F
• FMR52
I3 IECEx: Ex d [ia] IIC T6-T1 Ga/Gb • FMR51 XA00684F XA00684F XA00684F XA00692F XA00684F
IEXEx: Ex ta IIIC Txx°C Da/Db • FMR52
MC INMETRO: Ex d[ia] IIC T6 Ga/Gb • FMR51 XA01292F XA01292F XA01293F XA01298F XA01294F
• FMR52
8 Endress+Hauser
Micropilot FMR51, FMR52 HART Important document information
NC NEPSI Ex d[ia] IIC T6 Ga/Gb • FMR51 XA01202F XA01202F XA01202F XA01211F XA01202F
• FMR52
N2 NEPSI Ex ia IIC T6 Ga/Gb, Ex iaD 20/21 T85… • FMR51 XA01205F XA01205F XA01205F XA01214F -
90oC • FMR52
N3 NEPSI Ex d[ia] IIC T6 Ga/Gb, DIP A20/21 • FMR51 XA01206F XA01206F XA01206F XA01215F XA01206F
T85…90oC IP66 • FMR52
8A FM/CSA IS+XP Cl.I,II,III Div.1 Gr.A-G • FMR51 • XA01112F • XA01112F • XA01112F • XA01114F -
• FMR52 • XA01113F • XA01113F • XA01113F • XA01115F
• XA01116F • XA01116F • XA01116F • XA01118F
• XA01117F • XA01117F • XA01117F • XA01119F
For certified devices the relevant Safety Instructions (XA) are indicated on the
nameplate.
If the device is prepared for the remote display FHX50 (product structure: feature 030:
Display, Operation", option L or M), the Ex marking of some certificates changes according
to the following table 1):
N3 L or M NEPSI Ex d [ia] IIC T6-T1 Ga/Gb, DIP A20/21 [ia D] TA, Txx°C
IP6X
1) The marking of certificates not mentioned in this table are not affected by the FHX50.
Endress+Hauser 9
Basic safety instructions Micropilot FMR51, FMR52 HART
Residual risk
The electronics housing and its built-in components such as display module, main
electronics module and I/O electronics module may heat to 80 °C (176 °F) during operation
through heat transfer from the process as well as power dissipation within the electronics.
During operation the sensor may assume a temperature near the temperature of the
measured material.
10 Endress+Hauser
Micropilot FMR51, FMR52 HART Basic safety instructions
2.5.1 CE mark
The measuring system meets the legal requirements of the applicable EC guidelines. These
are listed in the corresponding EC Declaration of Conformity together with the standards
applied.
Endress+Hauser confirms successful testing of the device by affixing to it the CE mark.
Endress+Hauser 11
Product description Micropilot FMR51, FMR52 HART
3 Product description
1 1 1
2 4 5
3 3 3
A0016818
1 1 1
2 3 5
4 4 4
A0016788
12 Endress+Hauser
Micropilot FMR51, FMR52 HART Product description
1 2 3 5
9
6
7
–
Esc
+
8
E
A0012422
Endress+Hauser 13
Product description Micropilot FMR51, FMR52 HART
14 Endress+Hauser
Micropilot FMR51, FMR52 HART Incoming acceptance and product identification
1=2
A0022480
A0016871
A0015502
A0016872
A0022491
A0022494
If one of these conditions is not satisfied, contact your Endress+Hauser Sales Center.
Endress+Hauser 15
Incoming acceptance and product identification Micropilot FMR51, FMR52 HART
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The W@M Device Viewer: Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate or
scan the 2-D matrix code (QR code) on the nameplate.
4.2.1 Nameplate
92 (3.62)
2
1
Order code: 3 10
Ser. no.: 4
Ext. ord. cd.: 8
5
26
47 (1.85)
25
Tp max = 24 MWP: 6 9
23 LN = 7
Ta: 22 15
Mat.: 21
20
FW: 18 Dev.Rev.: 16 11
if modification
19 17 13 X = see sep. label
12
Date: 14
mm (in)
A0019444
Only 33 digits of the extended order code can be indicated on the nameplate. If the
extended order code exceeds 33 digits, the rest will not be shown. However, the
complete extended order code can be viewed in the operating menu of the device:
Extended order code 1 to 3 parameter
16 Endress+Hauser
Micropilot FMR51, FMR52 HART Storage, Transport
5 Storage, Transport
A0016875
Endress+Hauser 17
Installation Micropilot FMR51, FMR52 HART
6 Installation
A0016882
18 Endress+Hauser
Micropilot FMR51, FMR52 HART Installation
A0018944
A0016890
Endress+Hauser 19
Installation Micropilot FMR51, FMR52 HART
3
1
A0017123
20 Endress+Hauser
Micropilot FMR51, FMR52 HART Installation
a
W = 2 . D . tan _
2
D
a
A0016891
The beam angle is defined as the angle α where the energy density of the radar waves
reaches half the value of the maximum energy density (3-dB-width). Microwaves are also
emitted outside the signal beam and can be reflected off interfering installations.
Beam diameter W as a function of beam angle α and measuring distance D:
FMR51
3 m (9.8 ft) 1.22 m (4 ft) 0.95 m (3.1 ft) 0.53 m (1.7 ft) 0.42 m (1.4 ft)
6 m (20 ft) 2.44 m (8 ft) 1.9 m (6.2 ft) 1.05 m (3.4 ft) 0.84 m (2.8 ft)
9 m (30 ft) 3.66 m (12 ft) 2.85 m (9.4 ft) 1.58 m (5.2 ft) 1.26 m (4.1 ft)
12 m (39 ft) 4.88 m (16 ft) 3.80 m (12 ft) 2.1 m (6.9 ft) 1.68 m (5.5 ft)
15 m (49 ft) 6.1 m (20 ft) 4.75 m (16 ft) 2.63 m (8.6 ft) 2.10 m (6.9 ft)
20 m (66 ft) 8.14 m (27 ft) 6.34 m (21 ft) 3.50 m (11 ft) 2.80 m (9.2 ft)
25 m (82 ft) 10.17 m (33 ft) 7.92 m (26 ft) 4.37 m (14 ft) 3.50 m (11 ft)
30 m (98 ft) - 9.50 m (31 ft) 5.25 m (17 ft) 4.20 m (14 ft)
35 m (115 ft) - 11.09 m (36 ft) 6.12 m (20 ft) 4.89 m (16 ft)
40 m (131 ft) - 12.67 m (42 ft) 7.00 m (23 ft) 5.59 m (18 ft)
Endress+Hauser 21
Installation Micropilot FMR51, FMR52 HART
FMR52
22 Endress+Hauser
Micropilot FMR51, FMR52 HART Installation
• When using FMR54 with planar antenna, especially for media with low dielectric
constants, the end of the measuring range should not be closer than A: 1 m (3.28 ft) to
the flange.
• The smallest possible measuring range B depends on the antenna version (see figure).
• The tank height should be at least H (see table).
A
100%
H
B
C
0%
øD
A0018872
FMR51 50(1.97)
> 0.2 (0.7) 50 to 250 (1.97 to 9.84) > 0.3 (1.0)
FMR52 200(7.87)
minimum maximum
EN
DN50/PN16 4 45 65
DN80/PN16 8 40 55
DN100/PN16 8 40 60
DN150/PN16 8 75 115
ASME
2"/150lbs 4 40 55
Endress+Hauser 23
Installation Micropilot FMR51, FMR52 HART
minimum maximum
3"/150lbs 4 65 95
4"/150lbs 8 45 70
6"/150lbs 8 85 125
JIS
10K 50A 4 40 60
10K 80A 8 25 35
10K 100A 8 35 55
Alignment
• Align the antenna vertically to the product surface.
The maximum range may be reduced if the horn antenna is not vertically aligned.
• A marking at the flange (somewhere between the flange holes) or the boss enables
alignment of the antenna. This marking must be aligned towards the tank wall as well
as possible.
A B
°
90
°
90
°
90
° °
°
90 90
90
90 90
° °
90 90
° °
A0018974
Depending on the device version the marking may be a circle or two short parallel
lines.
Nozzle mounting
For optimum measurement, the tip of the antenna should extend below the nozzle.
Depending on the antenna size this is achieved by the following maximum nozzle heights:
24 Endress+Hauser
Micropilot FMR51, FMR52 HART Installation
Hmax
A0016820
Hmax
øD
A0023611
Endress+Hauser 25
Installation Micropilot FMR51, FMR52 HART
If the antenna doesn't extend below the nozzle, observe the following:
• The nozzle end must be smooth and free of burrs. If possible its edge should be
rounded.
• An interference echo suppression must be performed.
• Please contact Endress+Hauser for applications with higher nozzles than those
indicated in the table.
• For mounting in heigh nozzles the device is available in a version with an antenna
extension of up to 1 000 mm (39.4 in) 4)
• The antenna extension may cause interference echoes in the near range. In this
case it may occur that the maximum measurable level is reduced.
Threaded connection
For devices with a threaded connection it may be necessary - depending on the
antenna size - to unmount the horn before fastening the device and to mount it again
afterwards.
• Tighten with the hexagonal nut only.
• Tool : 55 mm hexagonal wrench
• Maximum permissible torque: 60 Nm (44 lbf ft)
Optimum thickness 1) 3.8 mm (0.15 in) 4.0 mm (0.16 in) 3.8 mm (0.15 in) 3.3 mm (0.13 in)
1) Other possible values for the thickness are multiples of the values listed (e.g. for PE: 7,6 mm (0.3 in), 11,4
mm (0.45 in)
26 Endress+Hauser
Micropilot FMR51, FMR52 HART Installation
Alignment
• Align the antenna vertically to the product surface.
The maximum range may be reduced if the horn antenna is not vertically aligned.
• A marking at the flange (somwhere between the flange holes) or the boss enables
alignment of the antenna. This marking must be aligned towards the tank wall as well
as possible.
A B
°
90
°
90
°
90
° °
°
90 90
90
90 90
° °
90 90
° °
A0018974
Depending on the device version the marking may be a circle or two short parallel
lines.
Nozzle mounting
Hmax
A0016819
• For flanges with PTFE cladding: Observe the notes on the mounting of cladded
flanges → 23.
• Usually, the PTFE flange cladding also serves as a seal between the nozzle and the
device flange.
Endress+Hauser 27
Installation Micropilot FMR51, FMR52 HART
°
90
1
A0016841
• For horn antenna: Align the marking towards the slots of the stilling well.
• Measurements can be performed through an open full bore ball valve without any
problems.
• After mounting, the housing can be turned 350° in order to facilitate access to the
display and the terminal compartment → 32.
28 Endress+Hauser
Micropilot FMR51, FMR52 HART Installation
A B A-A
A A 1
1 C
2 3
100%
100%
4
5
(5.91...19.7)
150…500
≤ 1 (0.04)
(5.91...19.7)
150…500
≤ 1 (0.04)
D 6
0%
0%
mm (in)
A0019009
Endress+Hauser 29
Installation Micropilot FMR51, FMR52 HART
°
90
1
°
90
A0019446
9 Installation in bypass
1 Marking for antenna alignment
2 Tank connectors
30 Endress+Hauser
Micropilot FMR51, FMR52 HART Installation
A
A-A
A A
≤ 1 (0.04)
2
C
(7.87) (7.87)
200
100%
200
3
4 B
4
3
(7.87) (7.87)
200
0%
200
mm (in)
A0019010
Endress+Hauser 31
Installation Micropilot FMR51, FMR52 HART
1
2
A0019142
If process temperatures are high, the device must be included in normal tank insulation to
prevent the electronics heating up as a result of heat radiation or convection. The
insulation may not exceed beyond the neck of the housing.
max. 350°
8 mm 8 mm
A0013713
32 Endress+Hauser
Micropilot FMR51, FMR52 HART Installation
–
+
E
3 mm
A0013905
1. If present: Loosen the screw of the securing clamp of the electronics compartment
cover using an Allen key and turn the clamp 90° conterclockwise.
2. Unscrew cover of the electronics compartment from the transmitter housing.
3. Pull out the display module with a gentle rotation movement.
4. Rotate the display module into the desired position: Max. 8 × 45 ° in each direction.
5. Feed the spiral cable into the gap between the housing and main electronics module
and plug the display module into the electronics compartment until it engages.
6. Screw the cover of the electronics compartment firmly back onto the transmitter
housing.
7. Tighten the securing clamp again using the Allen key (Torque: 2.5 Nm).
m Are the measuring point identification and labeling correct (visual inspection)?
Endress+Hauser 33
Electrical connection Micropilot FMR51, FMR52 HART
7 Electrical connection
2- w
4-2 ire le
0 v el
HA mA
[21 RT
4-2
0m
A ]
ope
A
n Sp
a
711 re pa
HA 20mA
08x rt
xx
RT
4...
+
1 -
1 2 4 5 6
mm
2
10
+ +
–
–
! 4...20 mA
3 B
7 +
1-c 1 -
1 2 4 5 han
nel 4-2 2
ove 0m
[16
] rvo A
ltag
ep
rote
ctio
n
+ + 711
286
– 17
–
! 4...20 mA
3
A0011294
34 Endress+Hauser
Micropilot FMR51, FMR52 HART Electrical connection
10
9
8
2- w
4-2 ire
0
H A mA
[02 RT
PF
S
A /03
] ope
n Sp
a
711 re pa
HA 20 mA
08x rt
3+ ++ xx
31 --
RT
4...
42 +
7
1 -
mm
2 6
4-
10
+ +
–
-
³250W 4...20 mA
1 2 3 4 5 B
3+ 11 +
3 -
4-2 4 +
0m
2-c
A/ 1 -
4-
han
nel 4- 2
[17
ove FIE 20mA
] rvo LD /
ltag
ep
B U
ro S
tec
tion
+ + 711
286
– 19
-
³250W 4...20 mA
1 2 3 4 5
A0013759
Endress+Hauser 35
Electrical connection Micropilot FMR51, FMR52 HART
14
13
12
2- w
4-2 ire le
0 v el
HA mA
[04 RT
4-2
0m
A /05
]
A
ope
A
n Sp
20m
a
711 re pa
HA 20mA
08x rt
xx
+
4 ...
3 -
RT
11
4 ...
4 +
1 -
mm
2
+
10
+
1 –
-
4...20 mA
9 8 4
+ +
2 –
-
4...20 mA
3 5 6 7 4
B
+ +
1 –
+
- 3 -
4...20 mA 4-2 4 +
10 0m
9 8 4 2-c
A/ 1 -
han
nel 4- 2
[17
ove FIE 20mA
] rvo LD /
ltag
ep
B US
ro tec
tion
+ + 711
28 6
2 – 19
-
4...20 mA
3 5 6 7 4
A0013923
This version is also suited for single-channel operation. In this case, current output 1
(terminals 1 and 2) must be used.
36 Endress+Hauser
Micropilot FMR51, FMR52 HART Electrical connection
13
12
11
2- w
4-2 ire
0
H A mA
[08 RT
A ]
= V
ope
48
n Sp
4...
a
711 re pa
HA 20 mA
08x rt
10.
L+ xx
1 L-
RT
4...
2 +
10 9
3 -
mm
4 8
10
7
+
-
³250W 4...20 mA
6
1 2 3 4 5
A0011340
Endress+Hauser 37
Electrical connection Micropilot FMR51, FMR52 HART
13
12
11
2- w
4-2 ire
0
HA mA
[09 RT
A ]
~
3V
ope
n
..25
Sp
a
711 re pa
HA 20 mA
9 0.
08x rt
xx
L
1 N
RT
4...
2 +
10 9
3 -
mm
4 8
10
7
+
-
³250W 4...20 mA
6
1 2 3 4 5
A0018965
LCAUTION
To ensure electrical safety:
‣ Do not disconnect the protective connection (6).
‣ Disconnect the supply voltage before disconnecting the protective earth (7).
Connect protective earth to the internal ground terminal (7) before connecting the
supply voltage. If necessary, connect the potential matching line to the external
ground terminal (11).
In order to ensure electromagnetic compatibility (EMC): Do not only ground the device
via the protective earth conductor of the supply cable. Instead, the functional
grounding must also be connected to the process connection (flange or threaded
connection) or to the external ground terminal.
An easily accessible power switch must be installed in the proximity of the device. The
power switch must be marked as a disconnector for the device (IEC/EN61010).
38 Endress+Hauser
Micropilot FMR51, FMR52 HART Electrical connection
+
1
3+ 2
3+
+
-
4-
4-
A0015909 A0015910
HART
• A normal device cable suffices if only the analog signal is used.
• A shielded cable is recommended if using the HART protocol. Observe grounding concept
of the plant.
• For 4-wire devices: Standard device cable is sufficient for the power line.
Endress+Hauser 39
Electrical connection Micropilot FMR51, FMR52 HART
4 3 1 Signal +
2 not connected
1 2 3 Signal -
4 Ground
A0011175
1 3 1 Signal -
2 Signal +
2 4 3 Not connected
4 Screen
A0011176
40 Endress+Hauser
Micropilot FMR51, FMR52 HART Electrical connection
"Power Supply, Output" 1) "Approval" 2) Terminal voltage U at the Maximum load R, depending on the supply voltage U0 at the
device supply unit
Ex ia / IS 10.4 to 30 V 3)
0
10 20 30 35 U0 [V]
10.4 21.4
A0017140
4)
• Ex d(ia) / XP 12 to 35 V R [W]
• Ex ic(ia)
• Ex nA(ia) 500
• Ex ta / DIP
Ex ia + Ex d(ia) / IS + XP 12 to 30 V 4)
0
10 20 30 35 U0 [V]
12 23
A0019136
"Power Supply, Output" 1) "Approval" 2) Terminal voltage U Maximum load R, depending on the supply voltage U0 at the
at the device supply unit
• Ex ia / IS 12 to 30 V 3)
0
• Ex ia + Ex d(ia) / IS + XP
10 20 30 35 U0 [V]
12 23
A0019136
Endress+Hauser 41
Electrical connection Micropilot FMR51, FMR52 HART
"Power Supply, Output" 1) "Approval" 2) Terminal voltage U at the Maximum load R, depending on the supply voltage U0 at the
device supply unit
0
10 20 30 U0 [V]
12 23
A0017055
42 Endress+Hauser
Micropilot FMR51, FMR52 HART Electrical connection
Technical data
Endress+Hauser 43
Electrical connection Micropilot FMR51, FMR52 HART
1. 3.
2.
5.
10 (0.4)
4.
5.
10 (0.4)
mm (in)
A0012619
1. Loosen the screw of the securing clamp of the connection compartment cover and
turn the clamp 90° counterclockwise.
2. Unscrew the connection compartment cover.
3. Push the cable through the cable entry. To ensure tight sealing, do not remove the
sealing ring from the cable entry.
4. Strip the cable.
5. Strip the cable ends 10 mm (0.4 in). For stranded cables, also attach wire end
ferrules.
6. Firmly tighten the cable glands.
7.
3
4
1
2
A0013837
44 Endress+Hauser
Micropilot FMR51, FMR52 HART Electrical connection
≤ 3 (0.12)
mm (in)
A0013661
m Are all cable glands installed, firmly tightened and correctly sealed?
m Does the supply voltage match the specifications on the transmitter nameplate?
If supply voltage is present: Is the device ready for operation and do values appear on the display
m
module?
Endress+Hauser 45
Operation options Micropilot FMR51, FMR52 HART
8 Operation options
8.1 Overview
Order code for "Display; Operation", option C "SD02" Order code for "Display; Operation", option E "SD03"
1 1
– –
+ +
E E
A0015544 A0015546
1 2 3
A0013137
46 Endress+Hauser
Micropilot FMR51, FMR52 HART Operation options
6 8
3
2
1 4 5 7
A0013764
3 –
+
E
2 1
A0014019
1 Service interface (CDI) of the measuring device (= Endress+Hauser Common Data Interface)
2 Commubox FXA291
3 Computer with "FieldCare" operating tool
Endress+Hauser 47
Operation options Micropilot FMR51, FMR52 HART
The parameter of the Expert menu are Output • Contains all parameters needed to
described in: configure the current output.
GP01014F (HART) • Contains all parameters neeed to
configure the switch output (PFS).
1) In case of operation via operating tools (e.g. FieldCare), the "Language" parameter is located at "Setup →
Advanced setup → Display"
2) only available with local operation
3) On entering the "Expert" menu, an access code is always requested. If a customer specific access code has
not been defined, "0000" has to be entered.
48 Endress+Hauser
Micropilot FMR51, FMR52 HART Operation options
Without access With access code Without access With access code
code code
(from the factory) (from the factory)
Operator --
Maintenance
If an incorrect access code is entered, the user obtains the access rights of the Operator
role.
The user role with which the user is currently logged on is indicated by the Access
status display parameter (for display operation) or Access status tooling parameter
(for tool operation).
Endress+Hauser 49
Operation options Micropilot FMR51, FMR52 HART
50 Endress+Hauser
Micropilot FMR51, FMR52 HART Operation options
The locking of the write access via local operation can be disabled by entering the device-
specific access code.
1. After you press , the input prompt for the access code appears.
2. Enter the access code.
The -symbol in front of the parameters disappears; all previously write-
protected parameters are now re-enabled.
Endress+Hauser 51
Operation options Micropilot FMR51, FMR52 HART
ON
CDI WP
OFF
XXXXXXXXXXXXX
–
+
E
3 mm
A0026157
A0013909
52 Endress+Hauser
Micropilot FMR51, FMR52 HART Operation options
4. Installing the lock switch (WP) on the main electronics module in the ON position
enables the hardware write protection. Installing the lock switch (WP) on the main
electronics module in the OFF position (factory setting) disables the hardware write
protection.
If the hardware write protection is enabled: The Hardware locked option is
displayed in the Locking status parameter. In addition to this, the -symbol
appears in the header of the measured value display and in the navigation view
in front of the parameters.
XXXXXXXXX
20.50
XX XX
A0015870
Endress+Hauser 53
Operation options Micropilot FMR51, FMR52 HART
When attempting to access the operating menu while the keylock is enabled, the
Keylock on message appears.
54 Endress+Hauser
Micropilot FMR51, FMR52 HART Operation options
2
1 2.1
2.3
2.2
1.1 2.6 2.4
1.3 2.5
OPEN
OPEN
1.2 3
ESC
1.4
3.1
E
3.2
5 4
User 20
ABC_
0 1 2 3 4
DEFG HIJK
LMNO PQRS TUVW 5 6 7 8 9
XYZ Aa1
A0012635
Endress+Hauser 55
Operation options Micropilot FMR51, FMR52 HART
Symbol Meaning
Display/operation
Is displayed:
A0011975
• in the main menu next to the selection "Display/operation"
• in the header, if you are in the "Display/operation" menu
Setup
Is displayed:
A0011974
• in the main menu next to the selection "Setup"
• in the header, if you are in the "Setup" menu
Expert
Is displayed:
• in the main menu next to the selection "Expert"
A0011976
• in the header, if you are in the "Expert" menu
Diagnostics
Is displayed:
• in the main menu next to the selection "Diagnostics"
A0011977
• in the header, if you are in the "Diagnostics" menu
Status signals
"Failure"
A device error is present. The measured value is no longer valid.
A0013956
"Function check"
The device is in service mode (e.g. during a simulation).
A0013959
"Out of specification"
The device is operated:
• Outside of its technical specifications (e.g. during startup or a cleaning)
A0013958
• Outside of the configuration carried out by the user (e.g. level outside configured span)
"Maintenance required"
Maintenance is required. The measured value is still valid.
A0013957
Symbol Meaning
Display parameter
Marks display-only parameters which can not be edited.
A0011978
Device locked
• In front of a parameter name: The device is locked via software and/or hardware.
A0011979 • In the header of the measured value screen: The device is locked via hardware.
56 Endress+Hauser
Micropilot FMR51, FMR52 HART Operation options
Symbol Meaning
Measured values
Level
A0011995
Distance
A0011996
Current output
A0011998
Measured current
A0011999
Terminal voltage
A0012106
A0012104
Measuring channels
Measuring channel 1
A0012000
Measuring channel 2
A0012107
Status "Alarm"
The measurment is interrupted. The output assumes the defined alarm value. A diagnostic
message is generated.
A0012102
Status "Warning"
The device continues measuring. A diagnostic message is generated.
A0012103
Endress+Hauser 57
Operation options Micropilot FMR51, FMR52 HART
Key Meaning
Minus key
For menu, submenu
Moves the selection bar upwards in a picklist.
A0013969
For text and numeric editor
In the input mask, moves the selection bar to the left (backwards).
Plus key
For menu, submenu
Moves the selection bar downwards in a picklist.
A0013970
For text and numeric editor
In the input mask, moves the selection bar to the right (forwards).
Enter key
For measured value display
• Pressing the key briefly opens the operating menu.
• Pressing the key for 2 s opens the context menu.
For menu, submenu
• Pressing the key briefly
Opens the selected menu, submenu or parameter.
A0013952
• Pressing the key for 2 s for parameter:
If present, opens the help text for the function of the parameter.
For text and numeric editor
• Pressing the key briefly
– Opens the selected group.
– Carries out the selected action.
• Pressing the key for 2 s confirms the edited parameter value.
A0013955
For measured value display
Enables or disables the keypad lock.
58 Endress+Hauser
Micropilot FMR51, FMR52 HART Operation options
2 20
0 1 2 3 4
5 6 7 8 9
3
A0013941 A0013999
1 Editing view
2 Display area of the entered values
3 Input mask
4 Operating elements
Input mask
The following input symbols are available in the input mask of the numeric and text editor:
A0016619
Confirms selection.
A0013985
A0016621
A0013986
A0014040
Toggle
Aa1 • Between upper-case and lower-case letters
• For entering numbers
A0013981
• For entering special characters
Endress+Hauser 59
Operation options Micropilot FMR51, FMR52 HART
Confirms selection.
A0013985
A0013987
A0013986
A0014040
A0013989
A0013991
A0013990
A0013988
60 Endress+Hauser
Micropilot FMR51, FMR52 HART Operation options
XXXXXXXXXX
Setup
20.50
Conf.backup disp
Simulation
kg/h
A0014003-EN
2. Press + simultaneously.
The context menu is closed and the operational display appears.
Endress+Hauser 61
Operation options Micropilot FMR51, FMR52 HART
E (2s)
2x +
E -
+ + -
+
+
E
+ + -
A0014277
62 Endress+Hauser
Micropilot FMR51, FMR52 HART System integration via HART protocol
The allocation of the device variables can be changed in the operating menu:
Expert → Communication → Output
In a HART multidrop loog only one device may use the output current for signal
transmission. For all other devices the follwing must be set:
• Current span (→ 138) = Fixed current
• Fixed current (→ 138) = 4 mA
Endress+Hauser 63
Commissioning via wizard Micropilot FMR51, FMR52 HART
A0027720
If the wizard is cancelled before all necessary parameters have been set, the device
may be in an undefined state. A reset to the default settings is recommended in this
case.
64 Endress+Hauser
Micropilot FMR51, FMR52 HART Commissioning via operating menu
XXXXXXXXX
20.50
XX XX
Main menu 0104-1
Language
English
Operation
Setup
Language 0104-1
à English
Deutsch
Español
Français
Language 0104-1
à English
Deutsch
Español
Français
Hauptmenü 0104-1
Sprache
Deutsch
Betrieb
Setup
A0013996
Endress+Hauser 65
Commissioning via operating menu Micropilot FMR51, FMR52 HART
100%
E
F
L 0%
A0016933
5) If, for example, the measuring range covers only an upper part of the tank (E << tank height), it is mandatory to enter the acutal tank height into
the "Setup → Advanced Setup → Level → Tank/silo height" parameter.
66 Endress+Hauser
Micropilot FMR51, FMR52 HART Commissioning via operating menu
The response time of the device is preset by the Tank type parameter (→ 105).
More detailed settings are possible in the Advanced setup submenu.
Endress+Hauser 67
Commissioning via operating menu Micropilot FMR51, FMR52 HART
68 Endress+Hauser
Micropilot FMR51, FMR52 HART Commissioning via operating menu
Endress+Hauser 69
Commissioning via operating menu Micropilot FMR51, FMR52 HART
70 Endress+Hauser
Micropilot FMR51, FMR52 HART Commissioning via operating menu
Endress+Hauser 71
Diagnostics and troubleshooting Micropilot FMR51, FMR52 HART
Device does not respond. Supply voltage does not match the Connect the correct voltage.
value indicated on the nameplate.
The cables do not contact the Ensure electrical contact between the
terminals properly. cable and the terminal.
Values on the display Contrast setting is too weak or too • Increase contrast by pressing and
invisible strong. simultaneously.
• Decrease contrast by pressing and
simultaneously.
The plug of the display cable is not Connect the plug correctly.
connected correctly.
Output current < 3.6 mA Signal cable connection incorrect. Check connection.
HART communication does Communication resistor missing or Install the communication resistor (
not function. incorrectly installed. 250 Ω) correctly → 34.
CDI communication does not Wrong setting of the COM port on Check the setting of the COM port on
work. the computer. the computer and change it if necessary.
72 Endress+Hauser
Micropilot FMR51, FMR52 HART Diagnostics and troubleshooting
No change of measured value Interference echo from installations, • Carry out tank mapping (Confirm
on filling / emptying nozzle or build-up on the antenna. distance parameter (→ 109)).
• If necessary, clean antenna
• If necessary, selet better mopunting
position
If the surface is not calm (e.g. Signal is weakened by the rough • Carry out tank mapping (Confirm
filling, emptying, agitator surface - the interference echoes are distance parameter (→ 109)).
running), the measured value sometimes stronger. • Select Tank type (→ 105) =
jumps sporadically to a Process vessel with agitator.
higher level • Increase integration time (Expert
→ Sensor → Distance → Integration
time)
• Optimize orientation of the antenna
• If necessary, select a better mounting
position and/or larger antenna.
Error message F941 or S941 Level echo is too weak. • Check Medium group parameter
"Echo lost" (→ 106).
• If necessary, select a more detailed
setting in Medium property
parameter (→ 117).
• Optimize alignment of antenna
• If necessary, select a better
installation position and/or larger
antenna.
Device displays a level when Interference echo Carry out mapping over entire
the tank is empty. measuring range when the tank is
empty (Confirm distance parameter
(→ 109)).
Wrong slope of the level in Wrong tank type selected. Set Tank type parameter (→ 105)
the entire measuring range correctly.
Endress+Hauser 73
Diagnostics and troubleshooting Micropilot FMR51, FMR52 HART
2 1
XXXXXXXXX S XXXXXXXXX S
20.50 S801
Supply voltage
3
4
X XX i Menu
5
A0013939-EN
1 Status signal
2 Status symbol (symbol for event level)
3 Status symbol with diagnostics event
4 Event text
5 Operating elements
Status signals
"Failure"
A device error is present. The measured value is no longer valid.
A0013956
"Function check"
The device is in service mode (e.g. during a simulation).
A0013959
"Out of specification"
The device is operated:
• Outside of its technical specifications (e.g. during startup or a cleaning)
A0013958
• Outside of the configuration carried out by the user (e.g. level outside configured span)
"Maintenance required"
Maintenance is required. The measured value is still valid.
A0013957
"Alarm" status
The measurement is interrupted. The signal outputs take on the defined alarm condition.
A0013961 A diagnostic message is generated.
"Warning" status
The device continues to measure. A diagnostic message is generated.
A0013962
74 Endress+Hauser
Micropilot FMR51, FMR52 HART Diagnostics and troubleshooting
Diagnostics event
↓ ↓ ↓
3-digit number
If two or more diagnostic messages are pending simultaneously, only the message with the
highest priority is shown. Additional pending diagnostic messages can be shown in
Diagnostic list submenu (→ 160).
Past diagnostic messages that are no longer pending are shown as follows:
• On the local display:
in Event logbook submenu (→ 161)
• In FieldCare:
via the "Event List /HistoROM" function.
Operating elements
Plus key
Opens the message about the remedial measures.
A0013970
Enter key
Opens the operating menu.
A0013952
Endress+Hauser 75
Diagnostics and troubleshooting Micropilot FMR51, FMR52 HART
XXXXXXXXX S XXXXXXXXX S
20.50 S801
Supply voltage
X XX i Menu
Diagnostic list S
Diagnostics 1
1 S801 Supply voltage
Diagnostics 2
Diagnostics 3
A0013940-EN
The user is in the Diagnostics menu at an entry for a diagnostics event, e.g. in Diagnostic
list submenu or in Previous diagnostics.
1. Press .
The message for the remedial measures for the selected diagnostic event opens.
2. Press + simultaneously.
The message for the remedial measures closes.
76 Endress+Hauser
Micropilot FMR51, FMR52 HART Diagnostics and troubleshooting
Endress+Hauser 77
Diagnostics and troubleshooting Micropilot FMR51, FMR52 HART
Diagnostic of electronic
Diagnostic of configuration
78 Endress+Hauser
Micropilot FMR51, FMR52 HART Diagnostics and troubleshooting
Diagnostic of process
6) This submenu is only available for operation via local display. In the case of operation via FieldCare, the event list can be displayed with the "Event
List / HistoROM" functionality of FieldCare.
Endress+Hauser 79
Diagnostics and troubleshooting Micropilot FMR51, FMR52 HART
In addition to the operation time of its occurrence, each event is also assigned a symbol
that indicates whether the event has occurred or is ended:
• Diagnostic event
– : Event has occurred
– : Event has ended
• Information event
: Event has occurred
I1089 Power on
80 Endress+Hauser
Micropilot FMR51, FMR52 HART Diagnostics and troubleshooting
The firmware version can explicitly be ordered via the product structure. In this way it
is possible to ensure compatibility of the firmware version with an existing or planned
system integration.
Endress+Hauser 81
Maintenance Micropilot FMR51, FMR52 HART
13 Maintenance
The measuring device requires no special maintenance.
82 Endress+Hauser
Micropilot FMR51, FMR52 HART Repairs
14 Repairs
Endress+Hauser 83
Repairs Micropilot FMR51, FMR52 HART
002847-A
6 3
4 1 5
Additional information: www.endress.com/deviceviewer
A0014979
14.3 Return
The measuring device must be returned if it is need of repair or a factory calibration, or if
the wrong measuring device has been delivered or ordered. Legal specifications require
Endress+Hauser, as an ISO-certified company, to follow certain procedures when handling
products that are in contact with the medium.
To ensure safe, swift and professional device returns, please refer to the procedure and
conditions for returning devices provided on the Endress+Hauser website at
http://www.endress.com/support/return-material
14.4 Disposal
Observe the following notes during disposal:
• Observe valid federal/national regulations.
• Ensure proper separation and reuse of the device components.
84 Endress+Hauser
Micropilot FMR51, FMR52 HART Accessories
15 Accessories
Accessory Description
222 (8.74)
A0015466
4)
65°
35°
(6.1
156
A0015472
Enclosed",
The weather protection cover can be ordered together with the device (product structure, feature 620 "Accessory
option PB "Weather Protection Cover").
Alternatively, it can be separately ordered as an accessory; order code 71162242.
Endress+Hauser 85
Accessories Micropilot FMR51, FMR52 HART
Accessory Description
A0019128
• Material:
– Plastics PBT
– CF3M (similar to 316L/1.4404)
– Aluminum (in preparation)
• Ingress protection: IP68 / NEMA 6P and IP66 / NEMA 4x
• Suitable for the display modules:
– SD02 (push buttons)
– SD03 (touch control)
• Connection cable:
– Cable with M12 plug; supplied with the FHX50; up to 30 m (98 ft)
– Customer supplied standard cable; up to 60 m (196 ft)
• Ambient temperature: –40 to 80 °C (–40 to 176 °F)
• If(feature
the remote display is to be used, the device must be ordered in the version "Prepared for display FHX50"
030, option L or M). For the FHX50, on the other hand, the option A: "Prepared for display FHX50" has
to be selected in feature 050: "Option Measurement Device".
• If a device has not been ordered in the version "Prepared for display FHX50", but is nevertheless to be equipped
with an FHX50, it is essential to select the option B: "Not prepared for display FHX50" in feature 050: "Option
Measurement Device" of the FHX50. In this case, a retrofit kit, needed to prepare the device for the remote
display, is supplied together with the FHX50.
the
For transmitters with approval, application of the FHX50 may be restricted. A device may only be retrofitted with
FHX50 if option L or M ("Prepared for FHX50") is quoted under Basic specifications, position 4 "Display,
operation" in the associated Safety Instructions (XA).
In addition to this, observe the Safety Instructions (XA) of the FHX50.
86 Endress+Hauser
Micropilot FMR51, FMR52 HART Accessories
Accessory Description
Hornschutz für
Hornantenne
80 mm (3 in) oder
100 mm (4 in) A
L
ød
øD
A0019143
A Horn antenna of the Micropilot (not supplied with the horn protection)
B Horn protection
⌀d Diameter of horn protection (see table below)
⌀D Minimum nozzle diameter (see table below)
L Length of antenna with horn protection (see table below)
Danger of explosion
Avoid electrostatic charging of the horn protection.
BC: Horn 80mm/3" 71105890 238 mm (9.4 in) 96 mm (3.78 in) ≥ DN100
BD: Horn 100mm/4" 71105889 302 mm (11.9 in) 116 mm (4.57 in) ≥ DN150
The horn protection can also be ordered together with the device. Product structure:
Feature 610 "Accessory Mounted", option OW "Horn protection, PTFE".
Endress+Hauser 87
Accessories Micropilot FMR51, FMR52 HART
Accessory Description
B
L
ød
øD
A0027190
BD: Horn 100mm/4" 71105889 267 mm (10.5 in) 116 mm (4.57 in) ≥ DN150
88 Endress+Hauser
Micropilot FMR51, FMR52 HART Accessories
Accessory Description
A0021734
Technical data
• Resistance per channel: 2 * 0.5 Ωmax
• Threshold DC voltage: 400 to 700 V
• Threshold impulse voltage: < 800 V
• Capacitance at 1 MHz: < 1.5 pF
• Nominal arrest impulse voltage (8/20 μs): 10 kA
• Suited for wire cross-sections: 0.2 to 2.5 mm2 (24 to 14 AWG)
Accessory Description
Gas-tight feedthrough Chemically inert glass feedthrough; prevents migration of gases into the electronics housing.
To be ordered with the device: product structure, feature 610 "Accessory Mounted", option NC "Gas-tight feedthrough"
Endress+Hauser 89
Accessories Micropilot FMR51, FMR52 HART
Commubox FXA195 For intrinsically safe HART communication with FieldCare via the USB interface.
HART
For details refer to Technical Information TI00404F
Accessory Description
Commubox FXA291 Connects Endress+Hauser field devices with CDI interface (= Endress+Hauser
Common Data Interface) to the USB interface of a computer.
Order code: 51516983
Accessory Description
HART Loop Converter Evaluates the dynamic HART variables and converts them to analog current signals
HMX50 or limit values.
Order code: 71063562
Accessory Description
Accessory Description
Fieldgate FXA320 Gateway for remote monitoring of connected 4-20mA measuring devices via web
browser.
Accessory Description
Fieldgate FXA520 Gateway for remote diagnosis and parametrization of connected HART measuring
devices via web browser.
Accessory Description
Field Xpert SFX350 Field Xpert SFX350 is a mobile computer for commissioning and maintenance. It
enables efficient device configuration and diagnostics for HART and FOUNDATION
fieldbus devices in the non-Ex area.
90 Endress+Hauser
Micropilot FMR51, FMR52 HART Accessories
Accessory Description
Field Xpert SFX370 Field Xpert SFX370 is a mobile computer for commissioning and maintenance. It
enables efficient device configuration and diagnostics for HART and FOUNDATION
fieldbus devices in the non-Ex area and the Ex area.
Graphic Data Manager The graphic data manager Memograph M provides information on all the relevant
Memograph M process variables. Measured values are recorded correctly, limit values are
monitored and measuring points analyzed. The data are stored in the 256 MB
internal memory and also on an SD card or USB stick.
RN221N Active barrier with power supply for safe separation of 4 to 20 mA current circuits.
Provides bi-directional HART transmission.
RNS221 Transmitter supply for 2-wire sensors or transmitters exclusively for non-Ex areas.
Provides bi-directional communication using the HART communication sockets.
Endress+Hauser 91
Operating menu Micropilot FMR51, FMR52 HART
16 Operating menu
Language → 146
Setup → 105
Level → 108
Distance → 108
‣ Mapping → 113
Distance → 113
92 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
‣ Level → 117
‣ Linearization → 123
Diameter → 128
‣ Edit table
Level → 130
Endress+Hauser 93
Operating menu Micropilot FMR51, FMR52 HART
94 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
‣ Display → 146
Language → 146
Header → 149
Separator → 150
Backlight → 151
Endress+Hauser 95
Operating menu Micropilot FMR51, FMR52 HART
‣ Administration → 155
Diagnostics → 158
Diagnostics 1 to 5 → 160
96 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Device ID → 163
Manufacturer ID → 164
Distance → 108
‣ Simulation → 171
Endress+Hauser 97
Operating menu Micropilot FMR51, FMR52 HART
98 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Setup → 105
Level → 108
Distance → 108
‣ Level → 117
Endress+Hauser 99
Operating menu Micropilot FMR51, FMR52 HART
‣ Linearization → 123
Diameter → 128
Level → 130
Level → 131
100 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Endress+Hauser 101
Operating menu Micropilot FMR51, FMR52 HART
‣ Display → 146
Language → 146
Header → 149
Separator → 150
Backlight → 151
‣ Administration → 155
Diagnostics → 158
102 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Timestamp → 158
Timestamp → 159
Diagnostics 1 to 5 → 160
Timestamp 1 to 5 → 160
Device ID → 163
Manufacturer ID → 164
Distance → 108
Endress+Hauser 103
Operating menu Micropilot FMR51, FMR52 HART
‣ Simulation → 171
104 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Navigation Setup
Device tag
Description Enter a unique name for the measuring point to identify the device quickly within the
plant.
Distance unit
Factory setting m
Tank type
Endress+Hauser 105
Operating menu Micropilot FMR51, FMR52 HART
Additional information Depending on the antenna some of the options mentioned above may not be available or
there may be additional options.
Tube diameter
Factory setting 0m
Medium group
Selection • Others
• Water based (DC >= 4)
Additional information This parameter roughly specifies the dielectric constant (DC) of the medium. For a more
detailed definition of the DC use the Medium property parameter (→ 117).
The Medium group parameter presets the Medium property parameter (→ 117) as
follows:
Others Unknown
The Medium property parameter can be changed at a later point of time. However,
when doing so, the Medium group parameter retains its value. Only the Medium
property parameter is relevant for the signal evaluation.
The measuring range may be reduced for small dielectric constants. For details refer
to the Technical Information (TI) of the respective device.
106 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Empty calibration
Description Specify the distance E between the process connection and the minimum level (0%). This
defines the starting point of the measuring range.
Additional information
0%
A0019486
The measuring range starts at the point at which the radar beam hits the tank or silo
bottom. In the case of dished boiler ends or conical outlets levels below this point can
not be measured.
Full calibration
Description Specify the distance F between the minimum level (0%) and the maximum level (100%).
Endress+Hauser 107
Operating menu Micropilot FMR51, FMR52 HART
Additional information
100%
0%
A0019487
Level
Additional information
0%
A0019482
Distance
Description Displays the measured distance D between the reference point (lower edge of the flange or
threaded connection) and the level.
108 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Additional information
A0019483
Signal quality
Confirm distance
Description Specify, whether the measured distance matches the real distance.
Depending on the selection the device automatically sets the range of mapping.
Endress+Hauser 109
Operating menu Micropilot FMR51, FMR52 HART
110 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Present mapping
Additional information This parameter defines up to which distance the new mapping is to be recorded. The
distance is measured from the reference point, i.e. from the lower edge of the mounting
flange or the threaded connection.
For reference purposes the Present mapping parameter (→ 111) is displayed
together with this parameter. It indicates up to which distance a mapping has already
been recorded.
Record map
Selection • No
• Record map
• Overlay map
• Factory map
• Delete partial map
Factory setting No
Endress+Hauser 111
Operating menu Micropilot FMR51, FMR52 HART
112 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Confirm distance
Description → 109
Description → 111
Record map
Description → 111
Distance
Description → 108
Endress+Hauser 113
Operating menu Micropilot FMR51, FMR52 HART
114 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Locking status
Description Indicates the write protection with the highest priority that is currently active.
Description Indicates access authorization to parameters via operating tool (e.g. FieldCare).
Additional information The access authorization can be changed via the Enter access code parameter
(→ 116).
If additional write protection is active, this restricts the current access authorization
even further. The write protection status can be viewed via the Locking status
parameter (→ 115).
Endress+Hauser 115
Operating menu Micropilot FMR51, FMR52 HART
Additional information If a symbol appears in front of a parameter, the parameter cannot be changed via
the local display with the current access authorization.
The access authorization can be changed via the Enter access code parameter
(→ 116).
If additional write protection is active, this restricts the current access authorization
even further. The write protection status can be viewed via the Locking status
parameter (→ 115).
Additional information • For local operation, the customer-specific access code, which has been defined in the
Define access code parameter (→ 155), has to be entered.
• If an incorrect access code is entered, the user retains his current access authorization.
• The write protection affects all parameters marked with the -symbol in this document.
On the local display, the -symbol in front of a parameter indicates that the parameter
is write-protected.
• If no key is pressed for 10 min, or the user switches from the navigation and editing
mode back to the measured value display mode, the device automatically locks the write-
protected parameters after another 60 s.
Please contact your Endress+Hauser Sales Center if you lose your access code.
116 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
"Level" submenu
Medium type
Additional information This parameter determines the value of several other parameters and strongly
influences the complete signal evaluation. Therefore, it is strongly recommended not
to change the factory setting.
Medium property
Selection • Unknown
• DC 1.4 ... 1.6
• DC 1.6 ... 1.9
• DC 1.9 ... 2.5
• DC 2.5 ... 4
• DC 4 ... 7
• DC 7 ... 15
• DC > 15
Factory setting Dependent on Medium type (→ 117) and Medium group (→ 106).
Solid Unknown
Others Unknown
For dielectric constants (DC values) of many media commonly used in various
industries refer to:
• the Endress+Hauser DC manual (CP01076F)
• the Endress+Hauser "DC Values App" (available for Android and iOS)
Endress+Hauser 117
Operating menu Micropilot FMR51, FMR52 HART
Additional information Max. filling speed liquid is preset by Tank type (→ 105). It can, however, be adjusted
to the process in the vessel at any time. If Tank type (→ 105) is changed again at a
later point of time, it may be necessary to repeat the fine adjustment.
Additional information Max. draining speed liquid (→ 118) is preset by Tank type (→ 105). It can,
however, be adjusted to the process in the vessel at any time. If Tank type (→ 105) is
changed again at a later point of time, it may be necessary to repeat the fine adjustment.
118 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Level unit
Factory setting %
Additional information The level unit may differ from the distance unit defined in the Distance unit parameter
(→ 105):
• The unit defined in the Distance unit parameter is used for the basic calibration (Empty
calibration (→ 107) and Full calibration (→ 107)).
• The unit defined in the Level unit parameter is used to display the (unlinearized) level.
Endress+Hauser 119
Operating menu Micropilot FMR51, FMR52 HART
Blocking distance
Additional information Signals in the blocking distance are only evaluated if they have been outside the blocking
distance when the device was switched on and move into the blocking distance due to a
level change during operation. Signals which are already in the blocking distance when the
device is switched on, are ignored.
This behavior is only valid if the following two conditions are met:
• Expert → Sensor → Echo tracking → Evaluation mode = Short time history or Long
time history)
• Expert → Sensor → Gas phase comp. → GPC mode= On, Without correction or
External correction
If one of these conditions is not met, signals in the blocking distance will always be
ignored.
If required, a different behavior for signals in the blocking distance can be defined by
the Endress+Hauser service.
BD
A0019492
Level correction
120 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Additional information The value specified in this parameter is added to the measured level (before linearization).
Tank/silo height
Description Specify total height of the tank or silo as measured from the process connection.
Additional information If the parametrized measuring range (Empty calibration (→ 107)) differs significantly
from the tank or silo height, it is recommended to enter the tank or silo height. Example:
Continuous level monitoring in the upper third of a tank or silo.
E
0%
1
A0019867
For tanks with conical outlet, Tank/silo height should not be changed as in this type
of applications Empty calibration (→ 107) is usually not << the tank or silo
height.
Endress+Hauser 121
Operating menu Micropilot FMR51, FMR52 HART
"Linearization" submenu
2
A
L
100%
L 1 B L‘
0%
M L‘
L
100%
C L2
L1
0% L‘1L‘2 L‘
L
100%
H
D
0% M L‘
L
100%
h
E
0% M L‘
L
100%
F
h 0% M L‘
L
100%
G d
0%
M L‘
L
100%
H d
0%
M L‘
A0019648
32 Linearization: Transformation of the level and (if relevant) the interface height into a volume or weight;
the transformation is dependent on the shape of the vessel.
1 Selection of linearization type and unit
2 Configuration of the linearization
A Linearization type (→ 125) = None
B Linearization type (→ 125) = Linear
C Linearization type (→ 125) = Table
D Linearization type (→ 125) = Pyramid bottom
E Linearization type (→ 125) = Conical bottom
F Linearization type (→ 125) = Angled bottom
G Linearization type (→ 125) = Horizontal cylinder
H Linearization type (→ 125) = Sphere
L Level before linearization (measured in distance units)
L' Level linearized (→ 127) (corresponds to volume or weight)
M Maximum value (→ 128)
d Diameter (→ 128)
h Intermediate height (→ 128)
122 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
‣ Linearization
Diameter → 128
‣ Edit table
Level → 130
Endress+Hauser 123
Operating menu Micropilot FMR51, FMR52 HART
‣ Linearization
Diameter → 128
Level → 130
Level → 131
124 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Description of parameters
Linearization type
Selection • None
• Linear
• Table
• Pyramid bottom
• Conical bottom
• Angled bottom
• Horizontal cylinder
• Sphere
Additional information
A B
100%
100%
0% 0%
C/D E
100% 100%
0% 0%
F/G
100%
0%
A0021476
33 Linearization types
A None
B Table
C Pyramid bottom
D Conical bottom
E Angled bottom
F Sphere
G Horizontal cylinder
Endress+Hauser 125
Operating menu Micropilot FMR51, FMR52 HART
126 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Custom-specific units
Free text
Factory setting %
Additional information The selected unit is only used to be indicated on the display. The measured value is not
transformed according to the selected unit.
It is also possible to configure a distance-to-distance linearization, i.e. a
transformation from the level unit to a different distance unit. To do so, select the
Linear linearization mode. In order to define the new level unit, select the Free text
option in the Unit after linearization parameter and enter the required unit into the
Free text parameter (→ 127).
Free text
Level linearized
Additional information The unit is defined by the Unit after linearization parameter → 126.
Endress+Hauser 127
Operating menu Micropilot FMR51, FMR52 HART
Maximum value
Description Specify the maximum content of the vessel (100%) measured in the units after
linearization.
Diameter
Factory setting 2m
Additional information The unit is defined in the Distance unit parameter (→ 105).
Intermediate height
Factory setting 0m
128 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Additional information
H
0%
A0013264
H Intermediate height
Table mode
Selection • Manual
• Semiautomatic
• Clear table
• Sort table
Before entering a linearization table, the values for Empty calibration (→ 107)
and Full calibration (→ 107) must be set correctly.
If values of the table need to be changed after the full or empty calibration have been
changed, a correct evaluation is only ensured if the existing table is deleted and the
complete table is entered again. To do so delete the existing table (Table mode
(→ 129) = Clear table). Then enter a new table.
Endress+Hauser 129
Operating menu Micropilot FMR51, FMR52 HART
The factory setting for the level unit is "%". If you want to enter the linearization table
in physical units, you must select the appropriate unit in the Level unit parameter
(→ 119) beforehand.
If a decreasing table is entered, the values for 20 mA and 4 mA of the current output
are interchanged. That means: 20 mA refers to the lowest level, whereas 4 mA refers
to the highest level. If required, the current output can be inverted in the Measuring
mode parameter.
Table number
User entry 1 to 32
Factory setting 1
Level (Manual)
Description Enter level value of the table point (value before linearization).
Factory setting 0%
130 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Level (Semiautomatic)
Description Displays measured level (value before linearization). This value is transmitted to the table.
Customer value
Factory setting 0%
Activate table
Selection • Disable
• Enable
Endress+Hauser 131
Operating menu Micropilot FMR51, FMR52 HART
Description Define the behavior of the output signal in case of a lost echo.
Additional information Use the unit which has been defined for the measured value output:
• without linearization: Level unit (→ 119)
• with linearization: Unit after linearization (→ 126)
132 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Description Define the slope of the ramp in the case of a lost echo.
Additional information
100%
B
A
C
0%
t
min
A0013269
• The unit for the slope of the ramp is "percentage of the measuring range per minute" (%/
min).
• For a negative slope of the ramp: The measured value is continuously decreased until it
reaches 0%.
• For a positive slope of the ramp: The measured value is continuosly increased until it
reaches 100%.
Blocking distance
Additional information Signals in the blocking distance are only evaluated if they have been outside the blocking
distance when the device was switched on and move into the blocking distance due to a
Endress+Hauser 133
Operating menu Micropilot FMR51, FMR52 HART
level change during operation. Signals which are already in the blocking distance when the
device is switched on, are ignored.
This behavior is only valid if the following two conditions are met:
• Expert → Sensor → Echo tracking → Evaluation mode = Short time history or Long
time history)
• Expert → Sensor → Gas phase comp. → GPC mode= On, Without correction or
External correction
If one of these conditions is not met, signals in the blocking distance will always be
ignored.
If required, a different behavior for signals in the blocking distance can be defined by
the Endress+Hauser service.
BD
A0019492
134 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Endress+Hauser 135
Operating menu Micropilot FMR51, FMR52 HART
Factory setting 0
Code incorrect
Description Indicates that a wrong unlocking code has been entered. Select procedure.
136 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Additional information Definition of the current range for the process variables
Process variable 4 mA value 20 mA value
1)
Level linearized 0 % or the associated 100 % 2) or the associated linearized value
linearized value
Distance 0 (i.e. level is at the reference Empty calibration (→ 107) (i.e. level is at
point) 0 %)
It may be necessary to adjust the 4mA and 20mA values to the application (especially
in the case of the Analog output adv. diagnostics 1/2 and Area of incoupling
options).
This can be done by the following parameters:
• Expert → Output → Curr.output 1 to 2 → Turn down
• Expert → Output → Curr.output 1 to 2 → 4 mA value
• Expert → Output → Curr.output 1 to 2 → 20 mA value
Endress+Hauser 137
Operating menu Micropilot FMR51, FMR52 HART
Current span
Description Select current range for process variable and alarm signal.
Selection • 4...20 mA
• 4...20 mA NAMUR
• 4...20 mA US
• Fixed current
Fixed current Constant current, defined in the Fixed current parameter (→ 138).
• In the case of an error, the output current assumes the value defined in the Failure
mode parameter (→ 139).
• If the meausred value is out of the measuring range, diagnostic message Current
output is issued.
In a HART multidrop loop only one device can use the analog current to transmit a
signal. For all other devices one must set:
• Current span = Fixed current
• Fixed current (→ 138) = 4 mA
Fixed current
Factory setting 4 mA
138 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Damping output
Description Define time constant τ for the damping of the output current.
Additional information Fluctuations of the measured value affect the output current with an exponential delay,
the time constant τ of which is defined in this parameter. With a small time constant the
output reacts immediately to changes of the measrued value. With a big time constant the
reaction of the output is more delayed. For τ = 0 (factory setting) there is no damping.
Failure mode
Selection • Min.
• Max.
• Last valid value
• Actual value
• Defined value
Endress+Hauser 139
Operating menu Micropilot FMR51, FMR52 HART
Failure current
Output current 1 to 2
140 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Selection • Off
• On
• Diagnostic behavior
• Limit
• Digital Output
Assign status
Selection • Off
• Digital output AD 1
• Digital output AD 2
Endress+Hauser 141
Operating menu Micropilot FMR51, FMR52 HART
Additional information The Digital output AD 1 and Digital output AD 2 options refer to the Advanced
Diagnostic Blocks. A switch signal generated in these blocks can be transmitted via the
switch output.
Assign limit
Selection • Off
• Level linearized
• Distance
• Terminal voltage
• Electronic temperature
• Relative echo amplitude
• Area of incoupling
Selection • Alarm
• Alarm or warning
• Warning
Switch-on value
142 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Factory setting 0
Additional information The switching behavior depends on the relative position of the Switch-on value and
Switch-off value parameters:
Switch-on value > Switch-off value
– The output is closed if the measured value is larger than Switch-on value.
– The output is opened if the measured value is smaller than Switch-off value.
B
t
D
t
A0015585
A Switch-on value
B Switch-off value
C Output closed (conductive)
D Output opened (non-conductive)
A
t
D
t
A0015586
A Switch-on value
B Switch-off value
C Output closed (conductive)
D Output opened (non-conductive)
Endress+Hauser 143
Operating menu Micropilot FMR51, FMR52 HART
Switch-on delay
Switch-off value
Factory setting 0
Additional information The switching behavior depends on the relative position of the Switch-on value and
Switch-off value parameters; description: see the Switch-on value parameter
(→ 142).
Switch-off delay
144 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Failure mode
Switch status
Selection • No
• Yes
Factory setting No
Endress+Hauser 145
Operating menu Micropilot FMR51, FMR52 HART
"Display" submenu
The Display submenu is only visible if a display module is connected to the device.
Language
Selection • English
• Deutsch *
• Français *
• Español *
• Italiano *
• Nederlands *
• Portuguesa *
• Polski *
• русский язык (Russian) *
• Svenska *
• Türkçe *
• 中文 (Chinese) *
• 日本語 (Japanese) *
• 한국어 (Korean) *
• Bahasa Indonesia *
• tiếng Việt (Vietnamese) *
• čeština (Czech) *
Factory setting The language selected in feature 500 of the product structure.
If no language has been selected: English
Format display
146 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Additional information
4841.000
1 Â mm
A0019963
1 Â
93.5 %
1 Â 159.0
mm
A0019964
1 Â 93.5
%
1 Â 159.0
mm
A0019965
1 Â 159.0 mm
V 1 Â 23.5 V
1 Â 93.5
%
A0019966
1 Â 93.5 %
1 Â 159.0 mm
V 1 Â 93.5 V
1 Â 26.3 °C
A0019968
• The Value 1 to 4 display → 148 parameters specify which measured values are
shown on the display and in which order.
• If more measured values are specified than the current display mode permits, the
values alternate on the device display. The display time until the next change is
configured in the Display interval parameter (→ 148).
Endress+Hauser 147
Operating menu Micropilot FMR51, FMR52 HART
Value 1 to 4 display
Description Select the measured value that is shown on the local display.
Selection • None 9)
• Level linearized
• Distance
• Current output 1 10)
• Measured current
• Current output 2
• Terminal voltage
• Electronic temperature
• Absolute echo amplitude
• Relative echo amplitude
• Analog output adv. diagnostics 1
• Analog output adv. diagnostics 2
• Area of incoupling
Decimal places 1 to 4
Description Select the number of decimal places for the display value.
Selection •x
• x.x
• x.xx
• x.xxx
• x.xxxx
Additional information The setting does not affect the measuring or computational accuracy of the device.
Display interval
Description Set time measured values are shown on display if display alternates between values.
148 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
User entry 1 to 10 s
Factory setting 5s
Additional information This parameter is only relevant if the number of selected measuring values exceeds the
number of values the selected display format can display simultaneously.
Display damping
Header
Additional information
1 XXXXXXXXX
A0013375
Endress+Hauser 149
Operating menu Micropilot FMR51, FMR52 HART
Header text
Additional information The number of characters which can be displayed depends on the characters used.
Separator
Selection •.
•,
Factory setting .
Number format
Selection • Decimal
• ft-in-1/16''
Additional information The ft-in-1/16'' option is only valid for distance units.
Description Select number of decimal places for the representation of numbers within the operating
menu.
150 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Selection •x
• x.x
• x.xx
• x.xxx
• x.xxxx
Additional information • Is only valid for numbers in the operating menu (e.g. Empty calibration, Full
calibration), but not for the measured value display. The number of decimal places for
the measured value display is defined in the Decimal places 1 to 4 → 148
parameters.
• The setting does not affect the accuracy of the measurement or the calculations.
Backlight
Prerequisite The device has the SD03 local display (with optical keys).
Selection • Disable
• Enable
Contrast display
Description Adjust local display contrast setting to ambient conditions (e.g. lighting or reading angle).
User entry 20 to 80 %
Endress+Hauser 151
Operating menu Micropilot FMR51, FMR52 HART
The configuration of the device can be saved to the display module at a certain point of
time (backup). The saved configurateion can be restored to the device if required, e.g. in
order to bring the device back into a defined state. The configuration can also be
transferred to a different device of the same type using the display module.
Operating time
User interface Days (d), hours (h), minutes (m), seconds (s)
Last backup
Description Indicates when the last data backup was saved to the display module.
User interface Days (d), hours (h), minutes (m), seconds (s)
Configuration management
Description Select action for managing the device data in the display module.
Selection • Cancel
• Execute backup
• Restore
• Duplicate
• Compare
• Clear backup data
152 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Backup state
Comparison result
Description Displays the comparison result between the device and the display.
Endress+Hauser 153
Operating menu Micropilot FMR51, FMR52 HART
154 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
"Administration" submenu
Factory setting 0
Additional information If the factory setting is not changed or 0 is defined as the access code, the parameters
are not write-protected and the configuration data of the device can then always be
modified. The user is logged on in the Maintenance role.
The write protection affects all parameters marked with the symbol in this
document. On the local display, the symbol in front of a parameter indicates that
the parameter is write-protected.
Once the access code has been defined, write-protected parameters can only be
modified if the access code is entered in the Enter access code parameter
(→ 116).
Please contact your Endress+Hauser Sales Center if you lose your access code.
For display operation: The new access code is only valid after it has been confirmed in
the Confirm access code parameter (→ 157).
Device reset
Selection • Cancel
• To factory defaults
• To delivery settings
• Of customer settings
• To transducer defaults
• Restart device
Endress+Hauser 155
Operating menu Micropilot FMR51, FMR52 HART
156 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Navigation Setup → Advanced setup → Administration → Def. access code → Def. access code
Description → 155
Navigation Setup → Advanced setup → Administration → Def. access code → Confirm code
Factory setting 0
Endress+Hauser 157
Operating menu Micropilot FMR51, FMR52 HART
Actual diagnostics
Timestamp
User interface Days (d), hours (h), minutes (m), seconds (s)
Previous diagnostics
Description Displays the last diagnostic message which has been active before the current message.
158 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Timestamp
User interface Days (d), hours (h), minutes (m), seconds (s)
Description Displays the time the device has been in operation since the last device restart.
User interface Days (d), hours (h), minutes (m), seconds (s)
Operating time
User interface Days (d), hours (h), minutes (m), seconds (s)
Endress+Hauser 159
Operating menu Micropilot FMR51, FMR52 HART
Diagnostics 1 to 5
Description Display the current diagnostics messages with the highest to fifth-highest priority.
Timestamp 1 to 5
User interface Days (d), hours (h), minutes (m), seconds (s)
160 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Filter options
Description Select category (status signal) whose event messages are displayed in the events list.
Selection • All
• Failure (F)
• Function check (C)
• Out of specification (S)
• Maintenance required (M)
• Information (I)
Additional information • This parameter is only used for operation via the local display.
• The status signals are categorized according to NAMUR NE 107.
Endress+Hauser 161
Operating menu Micropilot FMR51, FMR52 HART
Device tag
Serial number
Firmware version
Additional information For firmware versions differing only in the last two digits ("zz") there is no difference
concerning functionality or operation.
Device name
162 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Order code
Additional information The order code is generated from the extended roder code, which defines all device
features of the product structure. In contrast, the device features can not be read directly
from the order code.
Additional information The extended order code indicates the version of all the features of the product structure
and thus uniquely identifies the device.
Device revision
Description Displays the device revision registered for this device at the HART Communication
Foundation.
Additional information The device revision is used to allocate the correct Device Description file (DD) to the device.
Device ID
Additional information In addition to the Device type and Manufacturer ID, the Device ID is part of the unique
device identification (Unique ID) which characterizes each HART device unambiguously.
Endress+Hauser 163
Operating menu Micropilot FMR51, FMR52 HART
Device type
Description Displays the device type with which the device is registered with the the HART
Communication Foundation.
Additional information The device type is needed to allocate the correct Device Description file (DD) to the device.
Manufacturer ID
Description Displays the manufactured ID with which the device is registered with the HART
Communication Foundation.
164 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Distance
Description Displays the measured distance D between the reference point (lower edge of the flange or
threaded connection) and the level.
Additional information
A0019483
Level linearized
Additional information The unit is defined by the Unit after linearization parameter → 126.
Output current 1 to 2
Endress+Hauser 165
Operating menu Micropilot FMR51, FMR52 HART
Measured current 1
Terminal voltage 1
Electronic temperature
166 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Assign channel 1 to 4
Selection • Off
• Level linearized
• Distance
• Current output 1
• Measured current
• Current output 2 *
• Terminal voltage
• Electronic temperature
• Absolute echo amplitude
• Relative echo amplitude
• Area of incoupling
• Analog output adv. diagnostics 1
• Analog output adv. diagnostics 2
Additional information A total of 1000 measured values can be logged. This means:
• 1000 data points if 1 logging channel is used
• 500 data points if 2 logging channels are used
• 333 data points if 3 logging channels are used
• 250 data points if 4 logging channels are used
If the maximum number of data points is reached, the oldest data points in the data log
are cyclically overwritten in such a way that the last 1000, 500, 333 or 250 measured
values are always in the log (ring memory principle).
The logged data are deleted if a new option is selected in this parameter.
Logging interval
Endress+Hauser 167
Operating menu Micropilot FMR51, FMR52 HART
Additional information This parameter defines the interval between the individual data points in the data log, and
thus the maximum loggable process time T log :
• If 1 logging channel is used: T log = 1000 ⋅ t log
• If 2 logging channels are used: T log = 500 ⋅ t log
• If 3 logging channels are used: T log = 333 ⋅ t log
• If 4 logging channels are used: T log = 250 ⋅ t log
Once this time elapses, the oldest data points in the data log are cyclically overwritten such
that a time of T log always remains in the memory (ring memory principle).
The logged data are deleted if this parameter is changed.
Example
When using 1 logging channel
• Tlog = 1000 ⋅ 1 s = 1 000 s ≈ 16.5 min
• Tlog = 1000 ⋅ 10 s = 1 000 s ≈ 2.75 h
• Tlog = 1000 ⋅ 80 s = 80 000 s ≈ 22 h
• Tlog = 1000 ⋅ 3 600 s = 3 600 000 s ≈ 41 d
Selection • Cancel
• Clear data
168 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
• x-axis: depending on the number of selected channels, 250 to 1000 measured values of
a process variable are displayed.
• y-axis: covers the approximate measured value span and constantly adapts this to the
measurement.
To return to the operating menu, press and simultaneaously.
Endress+Hauser 169
Operating menu Micropilot FMR51, FMR52 HART
170 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
‣ Simulation
Endress+Hauser 171
Operating menu Micropilot FMR51, FMR52 HART
Description of parameters
Selection • Off
• Level
• Level linearized
Additional information • The value of the variable to be simulated is defined in the Process variable value
parameter (→ 172).
• If Assign measurement variable ≠ Off, a simulation is active. This is indicated by a
diagnotic message of the Function check (C) category.
Factory setting 0
Additional information Downstream measured value processing and the signal output use this simulation value. In
this way, users can verify whether the measuring device has been configured correctly.
Selection • Off
• On
172 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Additional information An active simulation is indicated by a diagnostic message of the Function check (C)
category.
Additional information The current output assumes the value specified in this parameter. In this way, users can
verify the correct adjustment of the current output and the correct function of connected
control units.
Selection • Off
• On
Switch status
Selection • Open
• Closed
Additional information The switch status assumes the value defined in this parameter. This helps to check correct
operation of connected control units.
Endress+Hauser 173
Operating menu Micropilot FMR51, FMR52 HART
Selection • Off
• On
Additional information When selecting the On option, the device generates an alarm. This helps to check the
correct output behavior of the device in the case of an alarm.
An active simulation is indicated by the diagnostic message C484 Failure mode
simulation.
174 Endress+Hauser
Micropilot FMR51, FMR52 HART Operating menu
Selection • No
• Yes
Factory setting No
Additional information In the case of a lost echo a device check can not be performed.
Description Displays the operating time at which the last device check has been performed.
Endress+Hauser 175
Operating menu Micropilot FMR51, FMR52 HART
Level signal
Description Displays result of the device check for the level signal.
Additional information For Level signal = Check not OK: Check the mounting position of the device and the
dielectric constant of the medium.
176 Endress+Hauser
Index
Index
A Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . 11
Access authorization to parameters Define access code . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Read access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Define access code (Parameter) . . . . . . . . . . . . 155, 157
Write access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Define access code (Wizard) . . . . . . . . . . . . . . . . . . 157
Access code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Incorrect input . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Device alarm simulation (Parameter) . . . . . . . . . . . . 174
Access status display (Parameter) . . . . . . . . . . . . . . 116 Device check (Submenu) . . . . . . . . . . . . . . . . . . . . . 175
Access status tooling (Parameter) . . . . . . . . . . . . . . 115 Device Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Accessories Device ID (Parameter) . . . . . . . . . . . . . . . . . . . . . . . 163
Communication specific . . . . . . . . . . . . . . . . . . . . 90 Device information (Submenu) . . . . . . . . . . . . . . . . 162
Device specific . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Device name (Parameter) . . . . . . . . . . . . . . . . . . . . 162
Service specific . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Device replacement . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Activate table (Parameter) . . . . . . . . . . . . . . . . . . . . 131 Device reset (Parameter) . . . . . . . . . . . . . . . . . . . . . 155
Actual diagnostics (Parameter) . . . . . . . . . . . . . . . . 158 Device revision (Parameter) . . . . . . . . . . . . . . . . . . . 163
Administration (Submenu) . . . . . . . . . . . . . . . . . . . 155 Device tag (Parameter) . . . . . . . . . . . . . . . . . . 105, 162
Advanced process conditions (Parameter) . . . . . . . . 118 Device type (Parameter) . . . . . . . . . . . . . . . . . . . . . 164
Advanced setup (Submenu) . . . . . . . . . . . . . . . . . . . 115 Diagnostic event
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 In the operating tool . . . . . . . . . . . . . . . . . . . . . . . 77
Residual risk . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Diagnostic events . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Assign channel 1 to 4 (Parameter) . . . . . . . . . . . . . . 167 Diagnostic list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Assign current output (Parameter) . . . . . . . . . . . . . . 137 Diagnostic list (Submenu) . . . . . . . . . . . . . . . . . . . . 160
Assign diagnostic behavior (Parameter) . . . . . . . . . . 142 Diagnostic message . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Assign limit (Parameter) . . . . . . . . . . . . . . . . . . . . . 142 Diagnostics
Assign measurement variable (Parameter) . . . . . . . . 172 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Assign status (Parameter) . . . . . . . . . . . . . . . . . . . . 141 Diagnostics (Menu) . . . . . . . . . . . . . . . . . . . . . . . . . 158
Diagnostics 1 to 5 (Parameter) . . . . . . . . . . . . . . . . . 160
B Diagnostics event . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Backlight (Parameter) . . . . . . . . . . . . . . . . . . . . . . . 151 Diameter (Parameter) . . . . . . . . . . . . . . . . . . . . . . . 128
Backup state (Parameter) . . . . . . . . . . . . . . . . . . . . 153 DIP switch
Blocking distance (Parameter) . . . . . . . . . . . . . 120, 133 see Write protection switch
Display (Submenu) . . . . . . . . . . . . . . . . . . . . . . . . . 146
C Display and operating module FHX50 . . . . . . . . . . . . 46
CE mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Display channel 1 to 4 (Submenu) . . . . . . . . . . . . . . 169
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Display damping (Parameter) . . . . . . . . . . . . . . . . . 149
Clear logging data (Parameter) . . . . . . . . . . . . . . . . 168 Display interval (Parameter) . . . . . . . . . . . . . . . . . . 148
Code incorrect (Parameter) . . . . . . . . . . . . . . . . . . . 136 Display module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Comparison result (Parameter) . . . . . . . . . . . . . . . . 153 Display symbols for submenus . . . . . . . . . . . . . . . . . . 56
Configuration backup display (Submenu) . . . . . . . . . 152 Display symbols for the locking state . . . . . . . . . . . . . 56
Configuration management (Parameter) . . . . . . . . . 152 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Configuration of a level measurement . . . . . . . . . . . . 66 Distance (Parameter) . . . . . . . . . . . . . . . . 108, 113, 165
Confirm access code (Parameter) . . . . . . . . . . . . . . . 157 Distance unit (Parameter) . . . . . . . . . . . . . . . . . . . . 105
Confirm distance (Parameter) . . . . . . . . . . . . . 109, 113 Document
Context menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Contrast display (Parameter) . . . . . . . . . . . . . . . . . . 151 Document function . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Current output 1 to 2 (Submenu) . . . . . . . . . . . . . . . 137
Current output 1 to 2 simulation (Parameter) . . . . . . 172 E
Current span (Parameter) . . . . . . . . . . . . . . . . . . . . 138 Electrical connection
Customer value (Parameter) . . . . . . . . . . . . . . . . . . 131 Commubox FXA291 . . . . . . . . . . . . . . . . . . . . . . . 47
Operating tools
D Via service interface (CDI) . . . . . . . . . . . . . . . . 47
Damping output (Parameter) . . . . . . . . . . . . . . . . . . 139 Electronic temperature (Parameter) . . . . . . . . . . . . . 166
Data logging (Submenu) . . . . . . . . . . . . . . . . . . . . . 167 Electronics housing
DD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Deactivate SIL/WHG (Wizard) . . . . . . . . . . . . . . . . . 136 Turning
Decimal places 1 (Parameter) . . . . . . . . . . . . . . . . . 148 see Turning the transmitter housing
Decimal places menu (Parameter) . . . . . . . . . . . . . . 150 Empty calibration (Parameter) . . . . . . . . . . . . . . . . . 107
Endress+Hauser 177
Index
H N
Hardware write protection . . . . . . . . . . . . . . . . . . . . . 52 Number format (Parameter) . . . . . . . . . . . . . . . . . . 150
HART device variables . . . . . . . . . . . . . . . . . . . . . . . . 63
HART integration . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 O
HART protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Operating elements
Header (Parameter) . . . . . . . . . . . . . . . . . . . . . . . . 149 Diagnostics message . . . . . . . . . . . . . . . . . . . . . . . 75
Header text (Parameter) . . . . . . . . . . . . . . . . . . . . . 150 Operating module . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Housing Operating time (Parameter) . . . . . . . . . . . . . . . 152, 159
Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Operating time from restart (Parameter) . . . . . . . . . 159
Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
I Order code (Parameter) . . . . . . . . . . . . . . . . . . . . . . 163
Input mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Output current 1 to 2 (Parameter) . . . . . . . . . . 140, 165
Intermediate height (Parameter) . . . . . . . . . . . . . . . 128 Output echo lost (Parameter) . . . . . . . . . . . . . . . . . . 132
Invert output signal (Parameter) . . . . . . . . . . . . . . . 145 Overvoltage protection
General information . . . . . . . . . . . . . . . . . . . . . . . 43
K
Keypad lock P
Disabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Prepare recording map (Parameter) . . . . . . . . . . . . . 113
Switch-on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Present mapping (Parameter) . . . . . . . . . . . . . . . . . 111
Previous diagnostics (Parameter) . . . . . . . . . . . . . . . 158
L Process variable value (Parameter) . . . . . . . . . . . . . . 172
Language (Parameter) . . . . . . . . . . . . . . . . . . . . . . . 146 Product safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Last backup (Parameter) . . . . . . . . . . . . . . . . . . . . . 152 PV (HART device variable) . . . . . . . . . . . . . . . . . . . . . 63
Last check time (Parameter) . . . . . . . . . . . . . . . . . . 175
Level (Parameter) . . . . . . . . . . . . . . . . . . 108, 130, 131 R
Level (Submenu) . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Ramp at echo lost (Parameter) . . . . . . . . . . . . . . . . . 133
Level correction (Parameter) . . . . . . . . . . . . . . . . . . 120 Read access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Level linearized (Parameter) . . . . . . . . . . . . . . 127, 165 Record map (Parameter) . . . . . . . . . . . . . . . . . 111, 113
Level measurement configuration . . . . . . . . . . . . . . . 66 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . . 14
Level signal (Parameter) . . . . . . . . . . . . . . . . . . . . . 176 Remedial measures
Level unit (Parameter) . . . . . . . . . . . . . . . . . . . . . . . 119 Calling up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Linearization (Submenu) . . . . . . . . . . . . . 123, 124, 125 Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Linearization type (Parameter) . . . . . . . . . . . . . . . . 125 Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Repair concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
178 Endress+Hauser
Index
Replacing a device . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 T
Requirements for personnel . . . . . . . . . . . . . . . . . . . . 10 Table mode (Parameter) . . . . . . . . . . . . . . . . . . . . . 129
Reset write protection (Parameter) . . . . . . . . . . . . . 136 Table number (Parameter) . . . . . . . . . . . . . . . . . . . . 130
Result device check (Parameter) . . . . . . . . . . . . . . . . 175 Tank type (Parameter) . . . . . . . . . . . . . . . . . . . . . . 105
Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Tank/silo height (Parameter) . . . . . . . . . . . . . . . . . 121
Terminal voltage 1 (Parameter) . . . . . . . . . . . . . . . . 166
S Timestamp (Parameter) . . . . . . . . . . . . . . 158, 159, 160
Safety instructions Transmitter
Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Turning the display module . . . . . . . . . . . . . . . . . 33
Safety Instructions (XA) . . . . . . . . . . . . . . . . . . . . . . . . 7 Turning the housing . . . . . . . . . . . . . . . . . . . . . . . 32
Safety settings (Submenu) . . . . . . . . . . . . . . . . . . . . 132 Transmitter housing
Separator (Parameter) . . . . . . . . . . . . . . . . . . . . . . . 150 Turning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Serial number (Parameter) . . . . . . . . . . . . . . . . . . . 162 Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Setting the operating language . . . . . . . . . . . . . . . . . 65 Tube diameter (Parameter) . . . . . . . . . . . . . . . . . . . 106
Settings Turning the display module . . . . . . . . . . . . . . . . . . . . 33
Manage device configuration . . . . . . . . . . . . . . . . 70 TV (HART device variable) . . . . . . . . . . . . . . . . . . . . . 63
Operating language . . . . . . . . . . . . . . . . . . . . . . . 65
Setup (Menu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 U
Signal quality (Parameter) . . . . . . . . . . . . . . . . . . . . 109 Unit after linearization (Parameter) . . . . . . . . . . . . . 126
SIL/WHG confirmation (Wizard) . . . . . . . . . . . . . . . 135
Simulation (Submenu) . . . . . . . . . . . . . . . . . . . 171, 172 V
Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Value 1 display (Parameter) . . . . . . . . . . . . . . . . . . 148
Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Value current output 1 to 2 (Parameter) . . . . . . . . . . 173
Start device check (Parameter) . . . . . . . . . . . . . . . . . 175 Value echo lost (Parameter) . . . . . . . . . . . . . . . . . . . 132
Status signals . . . . . . . . . . . . . . . . . . . . . . . . . . . 56, 74
Submenu W
Administration . . . . . . . . . . . . . . . . . . . . . . . . . . 155 W@M Device Viewer . . . . . . . . . . . . . . . . . . . . . . . . . 84
Advanced setup . . . . . . . . . . . . . . . . . . . . . . . . . 115 Wizard
Configuration backup display . . . . . . . . . . . . . . . 152 Deactivate SIL/WHG . . . . . . . . . . . . . . . . . . . . . . 136
Current output 1 to 2 . . . . . . . . . . . . . . . . . . . . . 137 Define access code . . . . . . . . . . . . . . . . . . . . . . . 157
Data logging . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Device check . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 SIL/WHG confirmation . . . . . . . . . . . . . . . . . . . . 135
Device information . . . . . . . . . . . . . . . . . . . . . . . 162 Workplace safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Diagnostic list . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Write access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 Write protection
Display channel 1 to 4 . . . . . . . . . . . . . . . . . . . . 169 Via access code . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Event list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 Via write protection switch . . . . . . . . . . . . . . . . . . 52
Event logbook . . . . . . . . . . . . . . . . . . . . . . . . . . 161 Write protection switch . . . . . . . . . . . . . . . . . . . . . . . 52
Events list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Linearization . . . . . . . . . . . . . . . . . . . 123, 124, 125
Measured values . . . . . . . . . . . . . . . . . . . . . . . . 165
Safety settings . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Simulation . . . . . . . . . . . . . . . . . . . . . . . . . 171, 172
Switch output . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
SV (HART device variable) . . . . . . . . . . . . . . . . . . . . . 63
Switch output (Submenu) . . . . . . . . . . . . . . . . . . . . 141
Switch output function (Parameter) . . . . . . . . . . . . . 141
Switch output simulation (Parameter) . . . . . . . . . . . 173
Switch status (Parameter) . . . . . . . . . . . . . . . . 145, 173
Switch-off delay (Parameter) . . . . . . . . . . . . . . . . . . 144
Switch-off value (Parameter) . . . . . . . . . . . . . . . . . . 144
Switch-on delay (Parameter) . . . . . . . . . . . . . . . . . . 144
Switch-on value (Parameter) . . . . . . . . . . . . . . . . . . 142
Symbols
For correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
In the text and numeric editor . . . . . . . . . . . . . . . . 59
System components . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Endress+Hauser 179
*71320530*
71320530
www.addresses.endress.com