Deep Drawing: Deep Drawing Is A Sheet Metal Forming Process in Which A Sheet Metal Blank Is Radially Drawn
Deep Drawing: Deep Drawing Is A Sheet Metal Forming Process in Which A Sheet Metal Blank Is Radially Drawn
Deep drawing is a sheet metal forming process in which a sheet metal blank is radially drawn
into a forming die by the mechanical action of a punch.[1] It is thus a shape transformation
process with material retention. The process is considered "deep" drawing when the depth of
the drawn part exceeds its diameter. This is achieved by redrawing the part through a series of
dies. The flange region (sheet metal in the die shoulder area) experiences a radial drawing
stress and a tangential compressive stress due to the material retention property. These
compressive stresses (hoop stresses) result in flange wrinkles (wrinkles of the first order).
Wrinkles can be prevented by using a blank holder, the function of which is to facilitate
controlled material flow into the die radius.
Contents
[hide]
1 Process
2 Variations
3 Workpiece materials and power requirements
4 Tool materials
5 Lubrication and cooling
6 See also
7 References
o 7.1 Bibliography
[edit] Process
The total drawing load consists of the ideal forming load and an additional component to
compensate for friction in the contacting areas of the flange region and bending forces at the
die radius. The forming load is transferred from the punch radius through the drawn part wall
into the deformation region (sheet metal flange). Due to tensile forces acting in the part wall,
wall thinning is prominent and results in an uneven part wall thickness. It can be observed that
the part wall thickness is lowest at the point where the part wall loses contact with the punch,
i.e. at the punch radius. The thinnest part thickness determines the maximum stress that can be
transferred to the deformation zone. Due to material volume constancy, the flange thickens
and results in blank holder contact at the outer boundary rather than on the entire surface. The
maximum stress that can be safely transferred from the punch to the blank sets a limit on the
maximum blank size (initial blank diameter in the case of rotationally symmetrical blanks).
An indicator of material formability is the limiting drawing ratio (LDR), defined as the ratio
of the maximum blank diameter that can be safely drawn into a cup without flange to the
punch diameter. Determination of the LDR for complex components is difficult and hence the
part is inspected for critical areas for which an approximation is possible. During severe deep
drawing the material work hardens and it may be necessary to anneal the parts in controlled
atmosphere ovens to restore the original elasticity of the material.
Commercial applications of this metal shaping process often involve complex geometries with
straight sides and radii. In such a case, the term stamping is used in order to distinguish
between the deep drawing (radial tension-tangential compression) and stretch-and-bend
(along the straight sides) components. Deep drawing is always accompanied by other forming
techniques within the press. These other forming methods include trimming, piercing,
bulging, reducing, ironing (wall thickness reduction), rolling or beading (often to create O-
ring seats), threading, sidewall piercing, crimping, date or pattern stamping and many others.It
common use to consider this process as a cost saving alternative to turned parts which require
much more raw material.
For high precision mass productions, it is always advisable to use a transfer press also known
as eyelet press. The advantage of this type of press, in respect to conventional progressive
presses, is that the parts is transferred from one die to the next by means of so called
"fingers". Not only do the fingers transfer the parts but they also guide the component during
the process. This allows parts to be drawn to the deepest depths with the tightest tolerances.
[edit] Variations
Deep drawing has been classified into conventional and unconventional deep drawing. The
main aim of any unconventional deep drawing process is to extend the formability limits of
the process. Some of the unconventional processes include hydromechanical deep drawing,
Hydroform process, Aquadraw process, Guerin process, Marform process and the hydraulic
deep drawing process to name a few.
The Marform process, for example, operates using the principle of rubber pad forming
techniques. Deep-recessed parts with either vertical or slopped walls can be formed. In this
type of forming, the die rig employs a rubber pad as one tool half and a solid tool half, similar
to the die in a conventional die set, to form a component into its final shape. Dies are made of
cast light alloys and the rubber pad is 1.5-2 times thicker than the component to be formed.
For Marforming, single-action presses are equipped with die cushions and blank holders. The
blank is held against the rubber pad by a blank holder, through which a punch is acting as in
conventional deep drawing. It is a double-acting apparatus: at first the ram slides down, then
the blank holder moves: this feature allows it to perform deep drawings (30-40% transverse
dimension) with no wrinkles.[2][3][4][5]
Industrial uses of deep drawing processes include automotive body and structural parts,
aircraft components, utensils and white goods. Complex parts are normally formed using
progressive dies in a single forming press or by using a press line.
1. ^ DIN 8584-3
2. ^ Totten, p. 30.
3. ^ Narayanan, p. 306.
4. ^ Wick, p. 5-78.
5. ^ Sala.
6. ^ Todd & Allen Alting.
7. ^ Manufacturing Processes Reference Guide, Industrial Press Inc., 1994.
[edit] Bibliography
Narayanan, S.; Kumar, K. Gokul; Reddy, K. Janardhan; Kuppan, P. (2006),
CAD/CAM Robotics and Factories of the Future: 22nd International Conference,
Alpha Science International Ltd., ISBN 817319792X, http://books.google.com/?
id=P40DBCGRNOUC.
Sala, Giuseppe (June 2001), "A numerical and experimental approach to optimise
sheet stamping technologies: part II — aluminium alloys rubber-forming", Materials
& Design 22 (4): 299–315, doi:10.1016/S0261-3069(00)00088-1,
http://www.sciencedirect.com/science?_ob=ArticleURL&_udi=B6TX5-4286KX2-
7&_user=10&_rdoc=1&_fmt=&_orig=search&_sort=d&view=c&_acct=C000050221
&_version=1&_urlVersion=0&_userid=10&md5=2e9fb2272a94cad76c5397e19a3dfc
19.
Todd, Robert (1994), Manufacturing Processes Reference Guide, New York:
Industrial Press inc., ISBN 0831130490.
Totten, George E.; Funatani, Kiyoshi; Xie, Lin (2004), Handbook of Metallurgical
Process Design, CRC Press, ISBN 0824741064, http://books.google.com/?
id=3zjfgq8pUvcC.
Wick, Charles; Veilleux, R. (1984), Tool and manufacturing engineers handbook:
Forming, 2, SME, ISBN 0872631354, http://books.google.com/?id=9ty5NPJ0UI4C.