Brief Operating Instructions Proline Prowirl R 200: Vortex Flowmeter
Brief Operating Instructions Proline Prowirl R 200: Vortex Flowmeter
Serial number
A0023555
2 Endress+Hauser
Proline Prowirl R 200 Table of contents
Table of contents
1 Document information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.1 Installation conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.2 Mounting the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.3 Post-installation check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.1 Connection conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.2 Connecting the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7.3 Hardware settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.4 Ensuring the degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
8 Operation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
8.1 Structure and function of the operating menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
8.2 Access to the operating menu via the local display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
8.3 Access to the operating menu via the operating tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
9 System integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
9.1 FOUNDATION Fieldbus cyclic data transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
9.2 Cyclic data transfer PROFIBUS PA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
10 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
10.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
10.2 Switching on the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
10.3 Setting the operating language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
10.4 Configuring the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
10.5 Defining the tag name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
10.6 Protecting settings from unauthorized access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
11 Diagnostic information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Endress+Hauser 3
Document information Proline Prowirl R 200
1 Document information
1.1 Symbols used
1.1.1 Safety symbols
Symbol Meaning
DANGER!
DANGER This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING!
WARNING This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION!
CAUTION This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTE!
NOTICE This symbol contains information on procedures and other facts which do not result in personal
injury.
Open-ended wrench
4 Endress+Hauser
Proline Prowirl R 200 Basic safety instructions
Permitted Preferred
Procedures, processes or actions that Procedures, processes or actions that
are permitted. are preferred.
Forbidden Tip
Procedures, processes or actions that Indicates additional information.
are forbidden.
Endress+Hauser 5
Basic safety instructions Proline Prowirl R 200
Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage caused
by improper or non-designated use.
LWARNING
Danger of breakage of the sensor due to corrosive or abrasive fluids or from
environmental conditions!
‣ Verify the compatibility of the process fluid with the sensor material.
‣ Ensure the resistance of all fluid-wetted materials in the process.
‣ Keep within the specified pressure and temperature range.
Verification for borderline cases:
‣ For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in
verifying the corrosion resistance of fluid-wetted materials, but does not accept any
warranty or liability as minute changes in the temperature, concentration or level of
contamination in the process can alter the corrosion resistance properties.
Residual risks
Possible burn hazard due to fluid temperatures!
‣ For elevated fluid temperature, ensure protection against contact to prevent burns.
6 Endress+Hauser
Proline Prowirl R 200 Product description
2.6 IT security
We only provide a warranty if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any
inadvertent changes to the device settings.
IT security measures in line with operators' security standards and designed to provide
additional protection for the device and device data transfer must be implemented by the
operators themselves.
3 Product description
The device consists of a transmitter and a sensor.
Two device versions are available:
• Compact version - transmitter and sensor form a mechanical unit.
• Remote version - transmitter and sensor are mounted in separate locations.
For detailed information on the product description, see the Operating Instructions for
the device.
Endress+Hauser 7
Incoming acceptance and product identification Proline Prowirl R 200
• If one of the conditions is not satisfied, contact your Endress+Hauser Sales Center.
• Depending on the device version, the CD-ROM might not be part of the delivery! The
Technical Documentation is available via the Internet or via the Endress+Hauser
Operations App.
8 Endress+Hauser
Proline Prowirl R 200 Storage and transport
Order code:
1 Ser. no.:
Ext. ord. cd.:
Order code:
2 Ser. no.: 4
Ext. ord. cd.:
A0021952
1 Example of a nameplate
1 Order code
2 Serial number (Ser. no.)
3 Extended order code (Ext. ord. cd.)
4 2-D matrix code (QR code)
For detailed information on the breakdown of the specifications on the nameplate, see
the Operating Instructions for the device .
A0015604
Do not remove protective covers or caps installed on process connections. They prevent
mechanical damage to the sealing surfaces and contamination in the measuring tube.
A0015606
10 Endress+Hauser
Proline Prowirl R 200 Installation
6 Installation
6.1 Installation conditions
6.1.1 Mounting position
Mounting location
A0015543
Orientation
The direction of the arrow on the sensor nameplate helps you to install the sensor according
to the flow direction.
Vortex meters require a fully developed flow profile as a prerequisite for correct volume flow
measurement. Therefore, please note the following:
A0015545
2) 3)
B Horizontal orientation, transmitter head up
A0015589
Endress+Hauser 11
Installation Proline Prowirl R 200
A0015590
4)
D Horizontal orientation, transmitter head at side
A0015592
1) In the case of liquids, there should be upward flow in vertical pipes to avoid partial pipe filling (Fig. A). Disruption
in flow measurement! In the case of vertical orientation and downward flowing liquid, the pipe always needs to
be completely filled to ensure correct liquid flow measurement.
2) Danger of electronics overheating! If the fluid temperature is ≥ 200 °C (392 °F) orientation B is not permitted for
the wafer version (Prowirl D) with nominal diameters DN 100 (4") and DN 150 (6").
3) In the case of hot media (e.g. steam or fluid temperature (TM) ≥ 200 °C (392 °F): orientation C or D
4) In the case of very cold media (e.g. liquid nitrogen): orientation B or D
5) For "wet steam detection/measurement" option: orientation C
L A
A0019211
The following dimensions must be observed to guarantee problem-free access to the device
for service purposes:
• A =100 mm (3.94 in)
• L = L + 150 mm (5.91 in)
Rotating the electronics housing and the display
The electronics housing can be rotated continuously by 360 °° on the housing support. The
display unit can be rotated in 45 ° stages. This means you can read the display comfortably
from all directions.
12 Endress+Hauser
Proline Prowirl R 200 Installation
Endress+Hauser 13
Installation Proline Prowirl R 200
1 2
15 × DN 5 × DN 20 × DN 5 × DN
3 4
25 × DN 5 × DN 40 × DN 5 × DN
5 6
20 × DN 5 × DN
h
17 × DN + 8 × h 5 × DN
7 8 DN ≤ 25 (1"):
50 × DN 5 × DN 5 × DN
9 DN ≥ 40 (1½"):
40 × DN 5 × DN
A0019189
14 Endress+Hauser
Proline Prowirl R 200 Installation
7 Control valve
8 Two measuring devices in a row where DN ≤ 25 (1"): directly flange on flange
9 Two measuring devices in a row where DN ≥ 40 (1½"): for spacing, see graphic
• If there are several flow disturbances present, the longest specified inlet run must be
maintained.
• If the required inlet runs cannot be observed, it is possible to install a specially
designed flow conditioner → 18.
For detailed information about inlet run correction and wet steam detection, see the
Special Documentation for the device
For the dimensions and installation lengths of the device, see the "Technical Information"
document, "Mechanical construction" section
Flow conditioner
If the required inlet runs cannot be observed, it is possible to install a specially designed flow
conditioner which can be ordered from Endress+Hauser. The flow conditioner is fitted
between two pipe flanges and centered by the mounting bolts. Generally this reduces the inlet
run needed to 10 × DN with full accuracy.
2 x DN 8 x DN 5 x DN
1
A0019208
1 Flow conditioner
The pressure loss for flow conditioners is calculated as follows: ∆ p [mbar] = 0.0085 ⋅ ρ
[kg/m3] ⋅ v2 [m/s]
Endress+Hauser 15
Installation Proline Prowirl R 200
abs. = absolute
For the dimensions of the flow conditioner, see the "Technical Information" document,
"Mechanical construction" section
Outlet runs when installing external devices
If installing an external device, observe the specified distance.
PT TT
3...5 x DN
4...8 x DN
A0019205
PT Pressure transmitter
TT Temperature transmitter
Compact version
Measuring device Non-Ex: –40 to +80 °C (–40 to +176 °F) 1)
1) Additionally available as order code for "Test, certificate", option JN "Transmitter ambient temperature –50 °C (–58
°F)".
Remote version
Transmitter Non-Ex: –40 to +80 °C (–40 to +176 °F) 1)
16 Endress+Hauser
Proline Prowirl R 200 Installation
1) Additionally available as order code for "Test, certificate", option JN "Transmitter ambient temperature –50 °C (–58
°F)".
‣ If operating outdoors:
Avoid direct sunlight, particularly in warm climatic regions.
Thermal insulation
For optimum temperature measurement and mass calculation, heat transfer at the sensor
must be avoided for some fluids. This can be ensured by installing thermal insulation. A wide
range of materials can be used for the required insulation.
This applies for:
• Compact version
• Remote sensor version
A0019212
‣ When insulating, ensure that a sufficiently large area of the housing support remains
exposed.
The uncovered part serves as a radiator and protects the electronics from overheating and
excessive cooling.
Endress+Hauser 17
Installation Proline Prowirl R 200
NOTICE
Electronics overheating on account of thermal insulation!
‣ Observe the maximum permitted insulation height of the transmitter neck so that the
transmitter head and/or the connection housing of the remote version is completely free.
‣ Observe information on the permissible temperature ranges .
‣ Note that a certain orientation might be required, depending on the fluid temperature
→ 11.
For detailed information about the fluid temperature, orientations and permitted
temperature ranges, refer to the Operating Instructions for the device
Vibrations
The correct operation of the measuring system is not affected by plant vibrations up to 1 g,
10 to 500 Hz. Therefore no special measures are needed to secure the sensors.
18 Endress+Hauser
Proline Prowirl R 200 Installation
3
Q
A0019209
For transmitter
• For turning the transmitter housing: Open-ended wrench8 mm
• For opening the securing clamps: Allen key3 mm
For sensor
For flanges and other process connections: Corresponding mounting tools
Endress+Hauser 19
Installation Proline Prowirl R 200
A0013964
LCAUTION
Excessive force can damage the housing!
‣ Avoid excessive mechanical stress.
20 Endress+Hauser
Proline Prowirl R 200 Installation
Wall mounting
! 8.6 (0.39)
80 (3.15)
M8
19 (0.6) 80 (3.15)
A0019864
Post mounting
! 20…70
(! 0.79 to 2.75)
4x SW 13
A0019862
Endress+Hauser 21
Installation Proline Prowirl R 200
max. 350°
8 mm 8 mm
A0013713
–
+
E
3 mm
A0013905
22 Endress+Hauser
Proline Prowirl R 200 Installation
Has the correct orientation for the sensor been selected → 11?
• According to sensor type
• According to medium temperature
• According to medium properties (outgassing, with entrained solids)
Does the arrow on the sensor nameplate match the direction of flow of the fluid through the piping
→ 11?
Are the measuring point identification and labeling correct (visual inspection)?
Is the device adequately protected from precipitation and direct sunlight?
Are the securing screw and securing clamp tightened securely?
Endress+Hauser 23
Electrical connection Proline Prowirl R 200
7 Electrical connection
The measuring device does not have an internal circuit breaker. For this reason, assign
the measuring device a switch or power-circuit breaker so that the power supply line can
be easily disconnected from the mains.
Electrical safety
In accordance with applicable federal/national regulations.
Signal cable
Current output
• For 4-20 mA: standard installation cable is sufficient.
• For 4-20 mA HART: Shielded cable recommended. Observe grounding concept of the plant.
Pulse/frequency/switch output
Standard installation cable is sufficient.
Current input
Standard installation cable is sufficient.
FOUNDATION Fieldbus
Twisted, shielded two-wire cable.
For further information on planning and installing FOUNDATION Fieldbus networks see:
• Operating Instructions for "FOUNDATION Fieldbus Overview" (BA00013S)
• FOUNDATION Fieldbus Guideline
• IEC 61158-2 (MBP)
24 Endress+Hauser
Proline Prowirl R 200 Electrical connection
PROFIBUS PA
Twisted, shielded two-wire cable. Cable type A is recommended.
For further information on planning and installing PROFIBUS PA networks see:
• Operating Instructions "PROFIBUS DP/PA: Guidelines for planning and commissioning"
(BA00034S)
• PNO Directive 2.092 "PROFIBUS PA User and Installation Guideline"
• IEC 61158-2 (MBP)
Standard cable 2 × 2 × 0.34 mm2 (22 AWG) PVC cable with common shield (2 pairs, pair-stranded)
Cable length 5 m (16 ft), 10 m (32 ft), 20 m (65 ft), 30 m (98 ft)
Operating temperature When mounted in a fixed position: –50 to +105 °C (–58 to +221 °F); when cable can
move freely: –25 to +105 °C (–13 to +221 °F)
Cable, reinforced 2 × 2 × 0.34 mm2 (22 AWG) PVC cable with common shield (2 pairs, pair-stranded)
and additional steel-wire braided sheath
Cable length 5 m (16 ft), 10 m (32 ft), 20 m (65 ft), 30 m (98 ft)
Operating temperature When mounted in a fixed position: –50 to +105 °C (–58 to +221 °F); when cable can
move freely: –25 to +105 °C (–13 to +221 °F)
Cable diameter
• Cable glands supplied:
M20 × 1.5 with cable 6 to 12 mm (0.24 to 0.47 in)
• Plug-in spring terminals for device version without integrated overvoltage protection: wire
cross-sections 0.5 to 2.5 mm2 (20 to 14 AWG)
• Screw terminals for device version with integrated overvoltage protection: wire cross-
sections 0.2 to 2.5 mm2 (24 to 14 AWG)
Endress+Hauser 25
Electrical connection Proline Prowirl R 200
Transmitter
Connection versions
3 2 1 4 3 2 1 4
+ – + –
5 6 + – + – 5 6
3 4 1 2 + – + –
3 4 1 2
A0020738 A0020739
Maximum number of terminals Maximum number of terminals for order code for
Terminals 1 to 6: "Accessory mounted", option NA "Overvoltage
Without integrated overvoltage protection protection"
• Terminals 1 to 4:
With integrated overvoltage protection
• Terminals 5 to 6:
Without integrated overvoltage protection
Pulse/frequency/switch
Option B 1) 4-20 mA HART (passive) -
output (passive)
Pulse/frequency/switch
Option E 1) 3) FOUNDATION Fieldbus -
output (passive)
Pulse/frequency/switch
Option G 1) 4) PROFIBUS PA -
output (passive)
26 Endress+Hauser
Proline Prowirl R 200 Electrical connection
Remote version
In the case of the remote version, the sensor and transmitter are mounted separately from
one another and connected by a connecting cable. The sensor is connected via the connection
housing while the transmitter is connected via the connection compartment of the wall holder
unit.
The way the transmitter wall holder is connected depends on the measuring device
approval and the version of the connecting cable used.
Connection is only possible via terminals:
• For approvals Ex n, Ex tb and cCSAus Div. 1
• If a reinforced connecting cable is used
The connection is via an M12 connector:
• For all other approvals
• If the standard connecting cable is used
Connection to the connection housing of the sensor is always via the terminals
(tightening torque for terminals: 1.2 to 1.7 Nm).
+ –
1 2 3 4
A0019335
6 Terminals for connection compartment in the transmitter wall holder and the sensor connection
housing
1 Terminals for connecting cable
2 Grounding via the cable strain relief
2 Grounding White
Endress+Hauser 27
Electrical connection Proline Prowirl R 200
PROFIBUS PA
Device plug for signal transmission (device side)
FOUNDATION Fieldbus
Device plug for signal transmission (device side)
28 Endress+Hauser
Proline Prowirl R 200 Electrical connection
potential equalization, therefore, cable shielding of fieldbus systems should only be grounded
on one side, for example at the fieldbus supply unit or at safety barriers.
NOTICE
In systems without potential matching, the multiple grounding of the cable shield causes
mains frequency equalizing currents!
Damage to the bus cable shield.
‣ Only ground the bus cable shield to either the local ground or the protective ground at one
end. Insulate the shield that is not connected.
1 2 3 4
+ +
- - 5
6
6 6
+ 5
-
6
6
8 . - 7
A0019004
Endress+Hauser 29
Electrical connection Proline Prowirl R 200
Supply voltage
Transmitter
Load
Load for current output: 0 to 500 Ω, depending on the external supply voltage of the power
supply unit
Calculation of the maximum load
Depending on the supply voltage of the power supply unit (US), the maximum load (RB)
including line resistance must be observed to ensure adequate terminal voltage at the device.
In doing so, observe the minimum terminal voltage
• RB ≤ (US - Uterm. min): 0.022 A
• RB ≤ 500 Ω
30 Endress+Hauser
Proline Prowirl R 200 Electrical connection
500
400
300
200
100
0
12 14 16 18 20 22 24 26 28 30 32 34 36 Us [V]
35
A0020417
Sample calculation
Supply voltage of the supply unit:
– US = 19 V
– Uterm. min = 12 V (measuring device) + 1 V (local operation without lighting) = 13 V
Maximum load: RB ≤ (19 V - 13 V): 0.022 A = 273 Ω
The minimum terminal voltage (Uterm. min) increases if local operation is used
(Verweisziel existiert nicht, aber @y.link.required='true').
Endress+Hauser 31
Electrical connection Proline Prowirl R 200
The way the transmitter wall holder is connected depends on the measuring device
approval and the version of the connecting cable used.
Connection is only possible via terminals:
• For approvals Ex n, Ex tb and cCSAus Div. 1
• If a reinforced connecting cable is used
The connection is via an M12 connector:
• For all other approvals
• If the standard connecting cable is used
Connection to the connection housing of the sensor is always via the terminals
(tightening torque for terminals: 1.2 to 1.7 Nm).
32 Endress+Hauser
Proline Prowirl R 200 Electrical connection
3 mm
A0020410
A0020411
1. NOTICE
Terminals tightened with an incorrect tightening torque.
Incorrect connection or damaged terminal.
‣ Tighten the terminals with a tightening torque in the 1.2 to 1.7 Nm range.
Wire the connecting cable:
Terminal 1 = brown cable
Terminal 2 = white cable
Terminal 3 = yellow cable
Terminal 4 = green cable
2. Connect the cable shield via the cable strain relief.
Endress+Hauser 33
Electrical connection Proline Prowirl R 200
A0020412
–
+
E
3 mm
A0020404
34 Endress+Hauser
Proline Prowirl R 200 Electrical connection
TX 10
8 mm
A0020405
~15°
A0020406
Endress+Hauser 35
Electrical connection Proline Prowirl R 200
A0020407
A0020409
36 Endress+Hauser
Proline Prowirl R 200 Electrical connection
3 mm 20 mm
10 (0.4)
mm (in)
A0013836
‣ Connect the cable in accordance with the terminal assignment . For HART communication:
when connecting the cable shielding to the ground terminal, observe the grounding
concept of the facility.
A0019147
Endress+Hauser 37
Electrical connection Proline Prowirl R 200
Requirements
Please consider the following to ensure correct measurement:
• Same electrical potential for the fluid and sensor
• Remote version: same electrical potential for the sensor and transmitter
• Company-internal grounding concepts
• Pipe material and grounding
For devices intended for use in hazardous locations, please observe the guidelines in the
Ex documentation (XA).
PROFIBUS PA
The address must always be configured for a PROFIBUS DP/PA device. The valid address
range is between 1 and 126. In a PROFIBUS DP/PA network, each address can only be
assigned once. If an address is not configured correctly, the device is not recognized by the
master. All measuring devices are delivered from the factory with the device address 126 and
with the software addressing method.
DIP
8
7
6
5
4
3
ON
98
2
1
A0015686
Hardware addressing
1. Set switch 8 to the "OFF" position.
2. Using switches 1 to 7, set the address as indicated in the table below.
The change of address takes effect after 10 seconds. The device is restarted.
Switch 1 2 3 4 5 6 7
38 Endress+Hauser
Proline Prowirl R 200 Electrical connection
ON DIP
98
1 2 3 4 5 6 7 8
2 + 8 = 10
A0015902
9 Example of hardware addressing; switch 8 is set to the "OFF" position; switches 1 to 7 define the
address.
Software addressing
1. Set switch 8 to "ON".
The device restarts automatically and reports the current address (factory setting:
126).
2. Configure the address via the operating menu: Setup menu→Communication
submenu→Device address parameter
ON DIP
98
1 2 3 4 5 6 7 8
A0015903
10 Example of software addressing; switch 8 is set to the "ON" position; the address is defined in the
operating menu ("Setup" menu→"Communication" submenu→"Device address" parameter).
To guarantee IP66/67 degree of protection, Type 4X enclosure, carry out the following steps
after the electrical connection:
1. Check that the housing seals are clean and fitted correctly. Dry, clean or replace the
seals if necessary.
2. Tighten all housing screws and screw covers.
3. Firmly tighten the cable glands.
Endress+Hauser 39
Electrical connection Proline Prowirl R 200
4. To ensure that moisture does not enter the cable entry, route the cable so that it loops
down before the cable entry ("water trap").
A0013960
40 Endress+Hauser
Proline Prowirl R 200 Operation options
8 Operation options
8.1 Structure and function of the operating menu
8.1.1 Structure of the operating menu
Operation
task-oriented
Setup
Diagnostics
Expert function-oriented
A0014058-EN
Endress+Hauser 41
Operation options Proline Prowirl R 200
1 2 XXXXXXX 2.1
2.3 19.184 mA
2.2
12.5 2.4
2.6 l/s
2.5
E 4 User
ABC_ DEFG HIJK
LMNO PQRS TUVW
XYZ Aa1
1.7 5 30
0 1 2 3 4
5 6 7 8 9
A0014013
1 Operational display with measured value shown as "1 value, max." (example)
1.1 Device tag
1.2 Display area for measured values (4-line)
1.3 Explanatory symbols for measured value: Measured value type, measuring channel number, symbol
for diagnostic behavior
1.4 Status area
1.5 Measured value
1.6 Unit for the measured value
1.7 Operating elements
2 Operational display with measured value shown as "1 bar graph + 1 value" (example)
2.1 Bar graph display for measured value 1
2.2 Measured value 1 with unit
2.3 Explanatory symbols for measured value 1: measured value type, measuring channel number
2.4 Measured value 2
2.5 Unit for measured value 2
2.6 Explanatory symbols for measured value 2: measured value type, measuring channel number
3 Navigation view: picklist of a parameter
3.1 Navigation path and status area
3.2 Display area for navigation: designates the current parameter value
4 Editing view: text editor with input mask
5 Editing view: numeric editor with input mask
42 Endress+Hauser
Proline Prowirl R 200 Operation options
Status area
The following symbols appear in the status area of the operational display at the top right:
• Status signals
– F: Failure
– C: Function check
– S: Out of specification
– M: Maintenance required
• Diagnostic behavior
– : Alarm
– : Warning
• : Locking (the device is locked via the hardware)
• : Communication (communication via remote operation is active)
Display area
• Measured variables (depending on the device version), e.g.:
– : Volume flow
– : Mass flow
– : Density
– G: Conductivity
– : Temperature
• : Totalizer (the measurement channel number indicates which totalizer is displayed)
• : Output (the measurement channel number indicates which output is displayed)
• : Input
• : Measurement channel number (if more than one channel is present for the same
measured variable type)
• Diagnostic behavior (for a diagnostic event that concerns the displayed measured variable)
– : Alarm
– : Warning
Status area
The following appears in the status area of the navigation view in the top right corner:
• Of the submenu
– The direct access code for the parameter you are navigating to (e.g. 0022-1)
– If a diagnostic event is present, the diagnostic behavior and status signal
• In the wizard
If a diagnostic event is present, the diagnostic behavior and status signal
Endress+Hauser 43
Operation options Proline Prowirl R 200
Display area
• Icons for menus
– : Operation
– : Setup
– : Diagnostics
– : Expert
• : Submenus
• : Wizards
• : Parameters within a wizard
• : Parameter locked
Input mask
Exits the input without applying the Inserts decimal separator at the input
changes. position.
.
Inserts minus sign at the input Clears all entered characters.
– position.
Exits the input without applying the Clears all entered characters.
changes.
Toggle
• Between upper-case and lower-case letters
Aa1 • For entering numbers
• For entering special characters
Clears all entered characters. Moves the input position one position
to the left.
Moves the input position one position Deletes one character immediately to
to the right. the left of the input position.
44 Endress+Hauser
Proline Prowirl R 200 Operation options
Minus key
Plus key
Enter key
In a menu, submenu
• Pressing the key briefly:
– Exits the current menu level and takes you to the next higher level.
– If help text is open, closes the help text of the parameter.
• Pressing the key for 2 s for the parameter: Returns you to the operational display ("home position").
With a wizard: Exits the wizard and takes you to the next higher level.
With a text and numeric editor: Closes the text or numeric editor without applying changes.
+ Plus/Enter key combination (press and hold down the keys simultaneously)
For operational display: Enables or disables the keypad lock (only SD02 display module).
Endress+Hauser 45
Operation options Proline Prowirl R 200
1 1 2
3
4
5
6 6
7 8 9 8 9 7 8 9 8 9
A0023460
46 Endress+Hauser
Proline Prowirl R 200 Operation options
1 2 3
7 6 7 6 7 6
A0019013
Endress+Hauser 47
Operation options Proline Prowirl R 200
3 –
+
E
2 1
A0020545
1 Service interface (CDI = Endress+Hauser Common Data Interface) of the measuring device
2 Commubox FXA291
3 Computer with "FieldCare" operating tool with COM DTM "CDI Communication FXA291"
8.3.2 FieldCare
Function scope
FDT-based plant asset management tool from Endress+Hauser. It can configure all smart field
devices in a system and helps you manage them. By using the status information, it is also a
simple but effective way of checking their status and condition.
Typical functions:
• Configuring parameters of transmitters
• Loading and saving device data (upload/download)
• Documentation of the measuring point
• Visualization of the measured value memory (line recorder) and event logbook
For additional information about FieldCare, see Operating Instructions BA00027S and
BA00059S
48 Endress+Hauser
Proline Prowirl R 200 Operation options
Establishing a connection
For additional information, see Operating Instructions BA00027S and BA00059S
User interface
2 3 4 5 6 7
Xxxxxx/…/…/
Device name: Xxxxxxx Mass flow: 12.34 kg/h
Device tag: Xxxxxxx
1 Volume flow: 12.34 m³/h
Status: Good
10 11
A0021051-EN
1 Header
2 Picture of device
3 Device name
4 Tag name
5 Status area with status signal
6 Display area for current measured values
7 Edit toolbar with additional functions such as save/restore, event list and create documentation
8 Navigation area with operating menu structure
9 Working area
10 Range of action
11 Status area
Endress+Hauser 49
System integration Proline Prowirl R 200
9 System integration
For detailed information on system integration, see the Operating Instructions for the
device.
Block model
The block model shows which input and output data the measuring device makes available for
cyclic data exchange. Cyclic data exchange takes place with a FOUNDATION Fieldbus master
(Class 1), e.g. a control system etc.
50 Endress+Hauser
Proline Prowirl R 200 System integration
7 Temperature
9 Volume flow
11 Mass flow
16 Totalizer 1
17 Totalizer 2
18 Totalizer 3
37 Flow velocity
38 Energy flow
48 Steam quality
50 Reynolds number
Channel Name
121 Channel_0
Endress+Hauser 51
System integration Proline Prowirl R 200
Structure
Channel_0
Value 3 Density
Value 4 Temperature
1) The compensation variables must be transmitted to the device in the SI basic unit
Uninitialized (factory
0 –
setting)
Channel Name
122 Channel_DO
52 Endress+Hauser
Proline Prowirl R 200 System integration
Structure
Channel_DO
Start heartbeat
Value 5 0 = off, 1 = start
verification 1)
Endress+Hauser 53
System integration Proline Prowirl R 200
Block model
The block model shows which input and output data the measuring device makes available for
cyclic data exchange. Cyclic data exchange takes place with a PROFIBUS master (Class 1), e.g.
a control system etc.
5 Totalizer block 1
TOTAL or
6 SETTOT_TOTAL or Totalizer block 2
SETOT_MODETOT_TOTAL
7 Totalizer block 3
To optimize the data throughput rate of the PROFIBUS network, it is advisable to only
configure modules that are processed in the PROFIBUS master system. If this results in gaps
between the configured modules, these gaps must be assigned to the EMPTY_MODULE.
54 Endress+Hauser
Proline Prowirl R 200 System integration
Factory setting
TOTAL module
Transmit a totalizer value from the measuring device to the PROFIBUS master (Class 1).
Selection: totalizer value
The totalizer value can be specified using the CHANNEL parameter.
Endress+Hauser 55
System integration Proline Prowirl R 200
Factory setting
SETTOT_TOTAL module
The module combination consists of the SETTOT and TOTAL functions:
• SETTOT: Control the totalizers via the PROFIBUS master.
• TOTAL: Transmit totalizer value, along with the status, to the PROFIBUS master.
Selection: control totalizer
33310 0 Totalize
33046 1 Resetting
Factory setting
SETTOT_MODETOT_TOTAL module
The module combination consists of the SETTOT, MODETOT and TOTAL functions:
• SETTOT: Control the totalizers via the PROFIBUS master.
• MODETOT: Configure the totalizers via the PROFIBUS master.
• TOTAL: Transmit totalizer value, along with the status, to the PROFIBUS master.
Selection: totalizer configuration
33306 0 Balancing
Factory setting
56 Endress+Hauser
Proline Prowirl R 200 System integration
Factory setting
Endress+Hauser 57
Commissioning Proline Prowirl R 200
EMPTY_MODULE module
This module is used to assign empty spaces arising from modules not being used in the slots
→ 54.
10 Commissioning
10.1 Function check
Before commissioning the measuring device:
‣ Make sure that the post-installation and post-connection checks have been performed.
• "Post-installation check" checklist → 22
• "Post-connection check" checklist → 40
If nothing appears on the local display or a diagnostic message is displayed, refer to the
Operating Instructions for the device
58 Endress+Hauser
Proline Prowirl R 200 Commissioning
XXXXXXXXX
20.50
XX XX
Main menu 0104-1
Language
English
Operation
Setup
Language 0104-1
à English
Deutsch
Español
Français
Language 0104-1
à English
Deutsch
Español
Français
Hauptmenü 0104-1
Sprache
Deutsch
Betrieb
Setup
A0013996
Wizard Meaning
Endress+Hauser 59
Diagnostic information Proline Prowirl R 200
Wizard Meaning
Low flow cut off Set the low flow cut off
Navigation
"Setup" menu → Device tag
Device tag Enter the name for the Max. 32 characters such as Prowirl
measuring point. letters, numbers or special
characters (e.g. @, %, /).
11 Diagnostic information
Faults detected by the self-monitoring system of the measuring device are displayed as a
diagnostic message in alternation with the operational display. The message on remedial
measures can be called up from the diagnostic message, and contains important information
on the fault.
60 Endress+Hauser
Proline Prowirl R 200 Diagnostic information
XXXXXXXXX S XXXXXXXXX S
20.50 S801
Supply voltage
X XX i Menu
Diagnostic list S
Diagnostics 1
1 S801 Supply voltage
Diagnostics 2
Diagnostics 3
A0013940-EN
Endress+Hauser 61
www.addresses.endress.com