Interactive Schematic: This Document Is Best Viewed at A Screen Resolution of 1024 X 768
Interactive Schematic: This Document Is Best Viewed at A Screen Resolution of 1024 X 768
Bookmarks X
*This document is best viewed at a
Options
screen resolution of 1024 X 768.
Features
Cover Page
To set your screen resolution do the following:
Tables RIGHT CLICK on the DESKTOP.
Component Select PROPERTIES.
Connector
CLICK the SETTINGS TAB.
Schematic
Machine Views
MOVE THE SLIDER under SCREEN RESOLUTION
Chassis View until it shows 1024 X 768.
Cab View CLICK OK to apply the resolution.
Engine View
*Due to different monitor sizes and PDF reader preferences
The Bookmarks panel will allow you to there may be some variance in linked schematic locations
quickly navigate to points of interest.
EC-C1
When only one callout is showing on a
machine view, clicking on this button will
Click on any text that is BLUE and make all of the callouts visible. This
underlined. These are hyperlinks button is located in the top right corner
that can be used to navigate the of every machine view page.
schematic and machine views.
© 2019 Caterpillar. All Rights Reserved. CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, “Caterpillar Yellow,” the “Power Edge”
and Cat “Modern Hex” trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
SCHEMATIC SYMBOLS AND DEFINITIONS
CHECK
ACCUMULATORS Unidirectional Bidirectional Control Line Restriction
Valves (Variable)
VARIABLE DISPLACEMENT
Basic Spring Shuttle NON- COMPENSATED
Pilot
Symbol Loaded Line Restriction
Controlled Spring Loaded Gas Charged Restriction
(Fixed)
Unidirectional Bidirectional
MAIN AUX.
PILOT CONTROL
Line Restriction 2-Section
RELEASED PRESSURE ROTATING SHAFTS Variable and Pressure
Compensated
Pump
Unidirectional Bidirectional
External Return Internal Return
Attachment Pump: Variable and
REMOTE SUPPLY PRESSURE Pressure Compensated
COMBINATION CONTROLS
LINES MEASUREMENT
Solenoid Solenoid Solenoid Solenoid and Servo Thermal Detent Crossing Joining
or Manual and Pilot Pilot or Manual Pressure Temperature Flow
Push-pull Lever Manual Shutoff General Manual Push Button Pedal Spring Vented Pressurized Return Above Fluid Level Return Below Fluid Level
Reed Switch: A switch whose contacts are controlled by a magnet. A magnet closes the contacts of Harness Connector Serialization Code: The "C" stands for
"Connector" and the number indicates which connector in the
a normally open reed switch; it opens the contacts of a normally closed reed switch.
harness (C1, C2, C3, ...)
L-C12
Sender: A component that is used with a temperature or pressure gauge. 3E-5179
The sender measures the temperature or pressure.
T Its resistance changes to give an indication to the gauge of the temperature or pressure. 5A
Component
Relay (Magnetic Switch): A relay is an electrical component that is activated by electricity. Fuse (5 Amps) 9X-1123 Part Number
It has a coil that makes an electromagnet when current flows through it.
The electromagnet can open or close the switch part of the relay. 325-AG135 PK-14
Harness identification code:
This example indicates wire group 325, Wire Gauge
Solenoid: A solenoid is an electrical component that is activated by electricity. wire 135 in harness "AG". Wire Color
It has a coil that makes an electromagnet when current flows through it.
The electromagnet can open or close a valve or move a piece of metal that can do work. 1 Deutsch connector: Typical representation
of a Deutsch connector. The plug contains all
2 sockets and the receptacle contains all pins.
Magnetic Latch Solenoid: An electrical component that is activated by electricity and held latched by a
permanent magnet. It has two coils (latch and unlatch) that make electromagnet 1 Sure-Seal connector: Typical representation
when current flows through them. It also has an internal switch that places of a Sure-Seal connector. The plug and receptacle
2 contain both pins and sockets.
the latch coil circuit open at the time the coil latches.
COMPONENT LOCATION
Part Machine Schematic
Description
Number Location Location
Cooler - Powertrain Oil 246-4988 1 D-1
Cooler - Powertrain Oil 246-4988 2 D-1
Filter Gp - Transmission Charge 346-5574 3 E-4
Final Drive Gp 254-7241 4 A-5, E-5
Manifold - Lube 130-3395 5 B-4
Pump Gp - PTO (4 Section) 295-1072 6 C-4
Screen - Pump Inlet 130-6747 7 C-4
Torque Convertor 121-0030 8 B-2
Transmission Ar 116-9491 9 B-6
Valve Gp - ECB 202-7400 10 C-5
Valve Gp - Priority 112-5326 11 B-6
Valve Gp - T/C Outlet Relief 237-8023 12 C-3
*Motor Gp - Gerotor 254-0148 13 E-7
*Valve Gp - Control 258-8894 14 E-7
Filter Gp - Oil 338-9802 15 E-4
Control Gp - Transmission 145-6480 16 C-6
Torque Convertor - Housing 343-9846 17 B-2
* These items are not shown on the component view.
TAP LOCATION
Tap Schematic
Description
Number Location
C1 Left Hand Clutch Pressure C-5
B1 Left Hand Brake Pressure C-5
C2 Right Hand Clutch Pressure C-5
B2 Right Hand Brake Pressure C-5
P1 Transmission Speed Clutch Pressure C-6
P2 Transmission Direction Clutch Pressure C-6
T Transmission Pump Pressure B-6
M Torque Convertor Inlet Pressure C-7
N Torque Convertor Outlet Pressure C-3
L2 System Lube Pressure B-4
L1 Transmission Lube Pressure C-7
LB1 Left Hand Clutch / Brake Lube Pressure E-5
LB2 Right Hand Clutch / Brake Lube Pressure A-5
SOS1 Transmission Filter Oil Sampling E-4
SOS2 Torque Convertor Filter Oil Sampling E-4
SOS3 Transmission Control Oil Sampling C-7
7 6 5 4 3 2 1
(13) MOTOR GP -
GEROTOR (PRIORITY)
340-2114
CLUTCH
254-7241
BRAKE
LUBE
E E
(14) VALVE GP -
RETURN TO TRANS CONTROL (LADDER)
258-8894
SUPPLY (TRANS)
(1) COOLER
POWERTRAIN OIL
246-4988
LADDER
(2) COOLER
POWERTRAIN OIL
246-4988
D D
FLYWHEEL HOUSING
L1
P1
A B C D E
C (12) VALVE GP
T/C OUTLET RELIEF
C
SOS3
TRANSMISSION B1 237-8023
CONTROL C-32
C2
M VALVE
P2 PTO PUMP
(7) SCREEN - PUMP INLET
130-6747
(16) CONTROLL GP
TRANSMISSION
T
145-6480
B TRANSMISSION
L2 B
A
(9) TRANSMISSION AR (11) VALVE GP
116-9491
PRIORITY (17) TORQUE CONVERTOR - HOUSING (8) TORQUE CONVERTOR
112-5326 343-9846 121-0030 ENGINE
LINE PATTERNS
Pressure Line
HYDRAULIC CIRCUIT COLOR DESCRIPTIONS Pilot / Load Sensing Pressure
(5) MANIFOLD - LUBE
LEFT BRAKE PRESSURE
130-3395 Drain / Return Lines
TRANSMISSION CHARGING PUMP OUTPUT
RIGHT BRAKE PRESSURE
TORQUE CONVERTOR CHARGING PUMP OUTPUT Air Line
RIGHT CLUTCH PRESSURE
SCAVENGE PUMP Component Group
SUPPLY LINE
DRAIN / RETURN LINE CALLOUTS
LEFT CLUTCH PRESSURE
LADDER CIRCUIT
YY Taps (Pressure, Sampling, Sensor - by letter)
BRAKE, LUBE, AND COOLING PUMP AND CIRCUIT
TRANSMISSION SCAVENGE PUMP OUTPUT
DL DL D Connectors (By letter)
BRAKE
(4) FINAL DRIVE GP Do not operate or work on this product unless you have MEDIA NUMBER: KENR5619-03
254-7241 read and understood the instruction and warnings in the
relevant Operation and Maintenance Manuals and SCHEMATIC PART NUMBER: 312-3500, CHANGE: 01, VERSION: -
relevant service literature. Failure to follow the instruc- Components are shown installed on a fully operable machine with the key and engine off, transmission shifter
LB2 tions or heed the warnings could result in injury or in neutral and with parking brake set.
death. Proper care is your responsibility.
Refer to the appropriate Service Manual for Troubleshooting, Specifications and Systems Operations.
Refer to the Parts Manual using a specific serial number prefix in SIS before ordering parts from this schematic.
7 6 5 4 3 2 1
POWER TRAIN
VIEW ALL CALLOUTS
4 LB1 10 7 6 3 SOS1 N 12
P1
2
SOS2
15
16
*inside Housing 8
17
SOS3
L2
L1 5
LB2
M
4
P2 9 T 11 C1 B1 B2 C2
TRANSMISSION
VIEW ALL CALLOUTS
P1 P2
SOS3
M
TRANSMISSION
SYSTEM
TEMPERATURE
L1