Professional Documents
Culture Documents
8 - Lab8-Potentiometric Titration of Acid Mixture
8 - Lab8-Potentiometric Titration of Acid Mixture
(B) Three or four 1.0 mL aliquots of your acid will be used for potentiometric
titrations. Each titration must be continued through two equivalence points.
II. INTRODUCTION
Strong acids, like hydrochloric acid, are completely dissociated in water, but weak acids,
like acetic acid, are only partially dissociated. The extent of dissociation can be
calculated from the value of the equilibrium constant and the amounts of weak acid and
strong base added to the solution.
The relative acidities of acids and bases are commonly expressed in terms of pKa = -
logKa, where Ka is the dissociation constant for the reaction
HA → H+ + AIn
the following derivation, aA- , [A-] , and A - represent, respectively, the activity, the molar
concentration, and the activity coefficient of the conjugate base, A-.
1
Since pKa ≡ - log Ka
2
Figure 1. Typical Plot of a Potentiometric Titration to Determine the Equivalence point
and pKa value (monoprotic acid).
Note that the pKa is the pH at which the activities of the acid HA and its conjugate base
A- are equal.
For a triprotic acid the successive dissociation constants are defined by:
The normality of an acid solution is the number of equivalents per liter (moles per liter)
of protons that it can dissociate. The normality of a solution of a base is equal to the
number of equivalents of acid it can neutralize. The normality of a solution of a triprotic
acid is three times its molarity. In discussing titrations of acid and base solutions, it is
often convenient to think in terms of milliequivalents.
Provided:
The TAs will prepare a solution of approximately 0.05 M NaOH as follows: Put
2.00 L of distilled water into the one gallon polyethylene bottle.2 Measure out 5.5 mL
of 50% w/w NaOH* in a 10 mL graduate cylinder and pour into the water in the
bottle.3 Both the solution bottle and 50% NaOH bottle should be closed immediately
with their polyethylene screw caps. Mix the dilute sodium hydroxide solution very
thoroughly by vigorous shaking with repeated inversions for at least a minute.
100 mg of reagent grade potassium acid phthalate* (KHP) was placed into a dry
weighing bottle, and placed in a 110 ºC drying oven for 1.5 hour or overnight.5 At the
end of the drying period, remove the weighing bottle from the oven and let cool in a
small desiccator charged with calcium chloride*. Leave the stopper off of the
weighing bottle until the first time the desiccator is opened after the KHP has cooled.
Weigh (to nearest 0.0001 g) by difference at least three samples of KHP into numbered
or otherwise identified 250-mL Erlenmeyer flasks. Sample weights should be 30 mg for
the primary standard.
3
Dissolve the KHP samples by swirling in 7 mL of water. Warming may be necessary. It
is essential that the samples dissolve completely; even a few small particles remaining
can cause a serious titration error.
Add 1 drop of phenolphthalein* indicator and titrate with the sodium hydroxide
solution from a buret.
The titration may be carried out rapidly at first, but the endpoint should be approached
carefully. With low-carbonate NaOH, the endpoint should be sharp and easily located
to within a fraction of a drop.6 Try to obtain the same intensity of pink color at the
endpoint for all your titrations. At the endpoint, the ideal indicator color is a barely
detectable shade of pale pink which persists for 30 seconds or more.
You will be given a mixture of these acids.* Your goal is to report the molarity of the
hydrochloric acid and the molarity of the phosphoric acid in the mixture, with their
uncertainties. You will also determine the value of pK2 for the phosphoric acid.
Using a VOLUMETRIC PIPET, pipet 1.00 mL of the acid mixture into a 30-50 mL
beaker and add 19.0 mL using graduated pipets of distilled H2O.
Rinse the pH electrode with distilled water into an empty beaker. and position the
electrode and 10 mL buret filled with sodium hydroxide as indicated in Figure 3. Be
sure that the pH electrode is not in a position to be damaged by the magnetic stir bar.
No air bubbles should be trapped under the polyethylene shield of the electrode. Also,
make sure that no air bubble is trapped in the tip of your buret.
Insulate the beaker from the magnetic stirrer with a layer of folded paper towel to
prevent warming of the solution by the magnetic stirrer.
4
Figure 3. Titration apparatus
With continuous stirring, add small increments of the approximately 0.05 M standard
solution of NaOH from the buret. Give the solution and pH meter time to equilibrate.
Read and record in the notebook the pH of the solution after addition of each portion of
the NaOH solution. Initially, the change of pH upon the addition of titrant will be
minimal. However, as the first equivalence point is approached, pH increments will
increase more rapidly, and only dropwise increments of NaOH should be added until it
Periodically the inside of the beaker may be washed down with distilled H2O from your
water bottle.
Warning: Be sure no drops are left on the tip of the buret when you are reading the pH.
The drop is part of the measured volume. You will not have good correlation between
volume and pH if part of the volume measured is left out. This is especially
Do not take pH readings above pH 11.5, because high pH damages the glass
electrode.
5
After the first potentiometric titration, remove the electrode from the solution, wash it
with distilled water and allow the electrode to stand in a beaker of distilled water for at
least 15 minutes before proceeding with the second titration. It is a good procedure to
check the calibration of the meter against a standard aqueous buffer of pH 7.0 before
beginning another titration.
While waiting, plot your data by hand or use your PC. Review your titration curve with
your TA. Discuss any changes which should be made for subsequent titrations.
Analyze the data from your titrations with Microsoft Excel as it is described in the lecture
handouts.
1. Plot your experimental data as pH versus volume of standard NaOH added. Use a full
sheet of graph paper for maximum accuracy and draw a smooth curve through the points.
2. For each titration identify the two equivalence points and draw vertical lines to
determine the corresponding volumes of NaOH. The portion of the titration curve
between the two equivalence points should follow the Henderson-Hasselbalch equation.
3. Calculate the pKa2 for H3PO4, and test the validity of the Henderson-Hasselbalch
equation by calculating several other points on this part of the titration curve.
a. How does your pKa2 value compare with the literature value?
b. Your titration does not yield values of pKa1 and pKa3 but something can be said
about these pKa values from your experimental data. What is it?
c. Since the titration will most likely not continue through pKa3, how does its value
depend the shape of the curve at the point where the titration ends if pKa3 is
approximated by extrapolation?
4. From the sample volume and the distances to the first and second equivalence points,
calculate the MOLARITIES of hydrochloric and phosphoric acids in the sample. Give
uncertainties for the calculated molarities. How well do your two or three titrations
agree?