Professional Documents
Culture Documents
DAV-DZ270 2 Manual Teatro en Casa
DAV-DZ270 2 Manual Teatro en Casa
Operating Instructions
DAV-DZ270 / HDZ278
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void your
authority to operate this equipment.
2GB
6) Clean only with dry cloth. outlet (mains), even if the unit itself has been turned
7) Do not block any ventilation openings. Install in off.
accordance with the manufacturer’s instructions. • Install this system so that the AC power cord (mains
8) Do not install near any heat sources such as lead) can be unplugged from the wall socket
radiators, heat registers, stoves, or other apparatus immediately in the event of trouble.
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or Note on power cord plug shapes
grounding-type plug. A polarized plug has two (Saudi Arabian model only)
blades with one wider than the other. A grounding For AC 220 V wall sockets
type plug has two blades and a third grounding
prong. The wide blade or the third prong are Make sure that the 13 A 3-pin plug (Type BF)
provided for your safety. If the provided plug does is securely attached to the power cord. (The 13
not fit into your outlet, consult an electrician for A 3-pin plug is attached when shipped from the
replacement of the obsolete outlet. factory.)
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution For AC 127 V wall sockets
when moving the cart/apparatus combination to 1 Remove the 13 A 3-pin plug using a
avoid injury from tip-over. screwdriver.
Precautions
On power sources
• AC power cord (mains lead) must be changed only at
the qualified service shop.
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
3GB
About This Operating
Instructions
• The instructions in this Operating Instructions
describe the controls on the remote. You can
also use the controls on the unit if they have the
same or similar names as those on the remote.
• The instructions in this manual are for DAV-
DZ270 and DAV-HDZ278. DAV-DZ270 is
the model used for illustration purposes. Any
difference in operation is clearly indicated in
the text, for example, “DAV-DZ270 only.”
• The Control Menu items may vary depending
on the area.
• “DVD” may be used as a general term for a
DVD VIDEO, DVD+RW/DVD+R, and DVD-
RW/DVD-R.
• Measurements are expressed in feet (ft) for
North American models.
• The default setting is underlined.
4GB
Table of Contents
About This Operating Instructions..........4 Other Operations
Playable Discs ......................................... 6 Getting Optimal Surround Sound for a
Getting Started Room .............................................. 78
Step 1: Positioning the System... 12 Calibrating the Appropriate Settings
Step 2: Connecting the System... 15 Automatically ................................. 79
Step 3: Performing the Quick Controlling the TV with the Supplied
Setup........................................ 27 Remote ........................................... 80
Step 4: Enjoying Sound from all the Using the Sound Effect......................... 81
Speakers.................................. 30 Using the Sleep Timer .......................... 81
Changing the Brightness of the Front
Sound Adjustment Panel Display.................................. 82
Enjoying Surround Sound by Using Viewing Information About the Disc ... 82
Decoding Mode ..............................32 Returning to the Default Settings ......... 85
Selecting the Sound Mode .................... 34
Additional Information
Enjoying Multiplex Broadcast Sound... 34
Precautions............................................ 86
Disc Notes about the Discs ........................... 87
Playing a Disc ....................................... 35 Troubleshooting.................................... 88
Using Play Mode................................... 40 Self-diagnosis Function ........................ 97
Searching/Selecting a Disc ...................43 Specifications........................................ 98
Playing MP3 Files/JPEG Image Files... 45 Glossary .............................................. 100
Enjoying DivX® Videos.......................48 Language Code List............................ 102
Adjusting the Delay Between the Picture Index to Parts and Control .................. 103
and Sound ....................................... 50 Guide to the Control Menu Display ... 107
Restricting Playback of the Disc........... 50 Index ................................................... 111
Using the Setup Display........................ 52
Tuner
Presetting Radio Stations ...................... 61
Listening to the Radio ........................... 62
Control for HDMI/External
Audio Device
Using the Control for HDMI Function for
“BRAVIA” Sync ............................ 64
Playing Back Audio Files/JPEG Image
Files of a USB Device .................... 67
Storing Songs in a USB Device ............73
Playable USB Devices .......................... 76
Using the DIGITAL MEDIA PORT
Adapter ........................................... 76
5GB
Playable Discs
Type Disc logo Characteristics Icon
DVD VIDEO • DVD VIDEO
• DVD-R/DVD-RW in DVD
VIDEO format or video mode
• DVD+R/DVD+RW in DVD
VIDEO format
DATA CD – • CD-R/CD-RW/CD-ROM in
DATA CD format, containing MP3
files1), JPEG image files2), and
DivX video files3)4)5), and
conforming to ISO 96606) Level 1/
Level 2, or Joliet (extended format)
DATA DVD – • DVD-ROM/DVD-R/DVD-RW/
DVD+R/DVD+RW in DATA
DVD format, containing MP3
files1), JPEG image files2), and
DivX video files3)4)5), and
conforming to UDF (Universal
Disk Format)
1)MP3 (MPEG1 Audio Layer 3) is a standard format defined by ISO/MPEG which compresses audio data. MP3 files
6GB
2)
JPEG image files must conform to the DCF image file format. (DCF “Design rule for Camera File system”: Image
standards for digital cameras regulated by Japan Electronics and Information Technology Industries Association
(JEITA).)
3)
Except for United Kingdom and North American models.
4) DivX® is a video file compression technology, developed by DivX, Inc.
5)
DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.
6)
A logical format of files and folders on CD-ROMs, defined by ISO (International Organization for
Standardization).
“DVD-RW,” “DVD+RW,” “DVD+R,”“DVD VIDEO,” and the “CD” logos are trademarks.
7GB
Note on DualDiscs
A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital
audio material on the other side. However, since the audio material side does not conform to the
Compact Disc (CD) standard, playback on this product is not guaranteed.
Region code
Your system has a region code printed on the rear of the unit and will only play a DVD labeled with
the same region code.
Copyrights
This product incorporates copyright protection technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly is prohibited.
This system incorporates with Dolby* Digital and Dolby Pro Logic (II) adaptive matrix surround
decoder and the DTS** Digital Surround System.
8GB
This system incorporates High-Definition Multimedia Interface (HDMITM) technology.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
9GB
Getting Started
Getting Started
Unpacking
• Front speakers (2) and • FM wire antenna (aerial) (1) • Calibration mic (1)
surround speakers (2)
or
• Operating Instructions
• Speaker and TV connections
• Video cord (1) (card)
• Subwoofer (1)
• Remote commander
(remote) (1)
10GB
Inserting batteries into the remote
Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the batteries to the
markings inside the compartment. To use the remote, point it at the remote sensor on the unit.
Getting Started
Note
• Do not leave the remote in an extremely hot or humid place.
• Do not use a new battery with an old one.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or lighting apparatus. Doing so may cause a malfunction.
• If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
,
Remove the foot pads from
the mount seat.
11GB
Step 1: Positioning the System
Getting Started
For the best possible surround sound, all the speakers other than the subwoofer should be placed at the
same distance from the listening position (A).
However, this system allows you to place the center speaker up to 1.6 meters (5 ft) closer (B) and the
surround speakers up to 5.0 meters (16 ft) closer (C) to the front speakers.
The front speakers can be placed from 1.0 to 7.0 meters (3 to 23 ft) (A) from the listening position.
C F
G Top view
E
A A A
A C B B
A
A A
D A
C C
D E
Note
• Do not set the speakers in an inclined position.
• Do not place the speakers in locations that are:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Subject to vibrations
– Subject to direct sunlight
• Use caution when placing the speakers and/or speaker stands attached to the speakers on a specially treated (waxed,
oiled, polished, etc.) floor, as staining or discoloration may result.
• Do not use any type of abrasive pad, scouring powder, or solvent such as alcohol or benzine.
• Do not lean or hang on the speaker, as the speaker may fall down.
Tip
• When you change the positions of the speakers, Sony recommends that you change the settings. For details, see
“Getting Optimal Surround Sound for a Room” (page 78) and “Calibrating the Appropriate Settings Automatically”
(page 79).
12GB
To install the speakers on a wall
Before installing the speakers on a wall, connect the speaker cord to the speaker.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with
Getting Started
the color tube to 3, and the speaker cord without the color tube to #.
Color tube
Front speaker (L): White
Front speaker (R): Red
Center speaker: Green
Surround speaker (L): Blue
Surround speaker (R): Gray
1 Prepare screws (not supplied) that are suitable for the hole on the back of each speaker.
See the illustrations below.
30 mm (1 3/16 inches) 10 mm
(13/32 inch)
8 to 10 mm
(11/32 to 13/32 inch)
8 to 10 mm
(11/32 to 13/32 inch)
10 mm
(13/32 inch)
13GB
Note
• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach
the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where
Getting Started
reinforcement is applied.
• Contact a screw shop or installer regarding the wall material or screws to be used.
• Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or
improper screw installation, natural calamity, etc.
14GB
Step 2: Connecting the System
Getting Started
See the connection diagram below, and read the additional information from 1 to 5 on the following
pages.
Note
• Be sure to make connections securely to avoid hum and noise.
• When you connect another component with a volume control, turn up the volume of the other components to a level
where sound is not distorted.
1 Center speaker
1 Subwoofer
15GB
1 Connecting the Speakers
Getting Started
The connector and color tube of the speaker cords are the same color as the label of the jacks to be
connected. Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker
cord with the color tube to 3, and the speaker cord without the color tube to #. Do not catch the
speaker cord insulation in the speaker terminals.
Rear of speaker
Color tube
(+)
(–)
Connector
DAV-DZ270
Rear panel
ANTENNA
SPEAKER
FRONT R FRONT L SUR R SUR L
COAXIAL 75
FM AM
SPEAKER
CENTER SUBWOOFER
R R
KE FE
SP
EA
SU
BW
OO
To the surround speaker (L)
ER
CE
NT
(blue)
T L
ON
FR
TR
ON
FR
16GB
DAV-HDZ278
Rear panel
ANTENNA
SPEAKER
Getting Started
FRONT R FRONT L SUR R SUR L
COAXIAL 75
FM AM
SPEAKER
DIGITAL IN
CENTER SUBWOOFER
DC5V
COAXIAL OPTICAL 0.7A MAX Y PB/CB PR/CR R AUDIO IN L
TV/VIDEO HDMI OUT DMPORT COMPONENT VIDEO OUT VIDEO OUT TV/VIDEO
R R
KE FE
SP
EA
SU
BW
OO
To the surround speaker (L)
ER
CE
NT
(blue)
TL
ON
FR
TR
ON
FR
17GB
2 Connecting the TV
Getting Started
To listen to TV sound from the six speakers of the system, connect the TV and the system with the
audio cord (not supplied) (A).
For video output to your TV, check the video input jacks of the TV, and select connection method A,
B, or C. Picture quality improves in order from A (standard) to C (HDMI).
When the TV has the digital optical or coaxial output jack, you can improve sound quality by
connecting with the digital cord (B) (DAV-HDZ278 only).
DAV-DZ270
Audio cord
(not supplied)
White
Red
IN L
R AUDIO
O
TV/VIDE
FRONT R
SPEAKER
FRONT L SUR R SUR L
ANTENNA
Rear panel
COAXIAL 75
FM AM
SPEAKER
CENTER SUBWOOFER
OUT
HDMI PR/CR
PB/CB OUT
Y EO
ENT VID
COMPON
18GB
DAV-HDZ278
Getting Started
(not supplied)
Audio cord
(not supplied)
Digital coaxial cord White
(not supplied) Red
IN L
L IN R AUDIO
DIGITA O
TV/VIDE
OPTICAL
COAXIAL EO
TV/VID
or
DC5V
COAXIAL OPTICAL 0.7A MAX Y PB/CB PR/CR R AUDIO IN L
TV/VIDEO HDMI OUT DMPORT COMPONENT VIDEO OUT VIDEO OUT TV/VIDEO
OUT
HDMI PR/CR
PB/CB OUT
Y EO
ENT VID
COMPON
* If your TV accepts progressive format signals, use this connection and set the output signal of the system to
progressive format (page 29).
** HDMI (High-Definition Multimedia Interface)
If your TV has the HDMI jack, use this connection and select the type of output signal (page 29).
Note
• During the “DMPORT” function, video signal is not output from the HDMI OUT and COMPONENT VIDEO OUT
jacks (DAV-HDZ278 only).
• The system can accept both digital and analog signals. Digital signals have priority over analog signals. (COAXIAL
has priority over OPTICAL.) If the digital signal ceases, the analog signal will be processed after 2 seconds. (DAV-
HDZ278 only.)
Tip
• You can connect another component, such as a VCR, digital satellite receiver, or PlayStation, to the TV/VIDEO
jacks (A or B*) instead of the TV.
* DAV-HDZ278 only.
19GB
To change the color system (PAL or NTSC) (Asian, Australian, and
Middle Eastern models only)
Depending on the TV to be connected, you may be required to select either PAL or NTSC for the color
Getting Started
system.
The initial setting of the system for Australian and Middle Eastern models is PAL.
The initial setting of the system for Asian models is NTSC.
1 Turn off the system by pressing "/1.
2 Turn on the system by pressing "/1 while pressing X on the unit.
Each time you perform this operation, the color system toggles between PAL and NTSC.
“NTSC” lights up in the front panel display when the color system is set to NTSC.
20GB
3 Connecting the other components
Getting Started
You can enjoy the connected component using the six speakers of the system.
• Portable audio source: A
• DIGITAL MEDIA PORT adapter: B (DAV-HDZ278 only)
DAV-DZ270
Stereo mini-plug cord
(not supplied)
Front panel
ANTENNA
FRONT R
SPEAKER
FRONT L SUR R SUR L Rear panel
COAXIAL 75
FM AM
SPEAKER
CENTER SUBWOOFER
Tip
• You can connect another
component, such as VCR,
instead of the TV. For
connection details, see page
18.
21GB
DAV-HDZ278
(not supplied)
Front panel
FRONT R
SPEAKER
FRONT L SUR R SUR L
ANTENNA
Rear panel
COAXIAL 75
FM AM
SPEAKER
DIGITAL IN
CENTER SUBWOOFER
DC5V
COAXIAL OPTICAL 0.7A MAX Y PB/CB PR/CR R AUDIO IN L
TV/VIDEO HDMI OUT DMPORT COMPONENT VIDEO OUT VIDEO OUT TV/VIDEO
DC5V X
Tip 0.7A MA
RT
DMPO
• You can connect another
component, such as VCR,
instead of the TV. For
connection details, see page
18.
DIGITAL MEDIA PORT adapter
(not supplied)
Connect a DIGITAL MEDIA PORT adapter (not supplied) to the DMPORT jack. For details, see
“Using the DIGITAL MEDIA PORT Adapter” (page 76).
Note
• Connect the DIGITAL MEDIA PORT adapter so that the V marks are aligned. When disconnecting, pull out while
pressing A.
22GB
If your TV has multiple audio/video inputs
You can enjoy the sound with the speakers of the system through the connected TV. Connect the
components as follows.
Getting Started
TV VCR, digital satellite receiver
or PlayStation, etc.
System
:Signal flow
Select the component on the TV. For details, refer to the operating instructions of the TV.
If the TV does not have multiple audio/video inputs, a switcher will be necessary to receive the sound
from more than two components.
23GB
4 Connecting the antenna (aerial)
Getting Started
DAV-DZ270
B
Note
• Cord (A) or cord (B) can be connected to either
terminal.
FRONT R
SPEAKER
FRONT L SUR R SUR L
ANTENNA
Rear panel
COAXIAL 75
FM AM
SPEAKER
CENTER SUBWOOFER
NNA
ANTE
FM wire antenna (aerial)
(supplied)
IAL 75
COAX
FM
or
24GB
DAV-HDZ278
Getting Started
(supplied)
Note
• Cord (A) or cord (B) can be connected to either
terminal.
FRONT R
SPEAKER
FRONT L SUR R SUR L
ANTENNA
Rear panel
COAXIAL 75
FM AM
SPEAKER
DIGITAL IN
CENTER SUBWOOFER
DC5V
COAXIAL OPTICAL 0.7A MAX Y PB/CB PR/CR R AUDIO IN L
TV/VIDEO HDMI OUT DMPORT COMPONENT VIDEO OUT VIDEO OUT TV/VIDEO
NNA
ANTE
FM wire antenna (aerial)
(supplied)
IAL 75
COAX
FM
or
Note
• Keep the AM loop antenna (aerial) and cord away from the system or other AV components, as noise may result.
• Be sure to fully extend the FM wire antenna (aerial).
• After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
Tip
• Adjust the direction of the AM loop antenna (aerial) for best AM broadcast sound.
• If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM
antenna (aerial) as shown below.
COAXIAL 75
FM AM
25GB
5 Connecting the AC power cord (mains lead)
Getting Started
Before connecting the AC power cord (mains lead) of the unit to a wall outlet (mains), connect all the
speakers to the unit.
DAV-DZ270
Rear panel
ANTENNA
SPEAKER
FRONT R FRONT L SUR R SUR L
COAXIAL 75
FM AM
SPEAKER
CENTER SUBWOOFER
DAV-HDZ278
Rear panel
ANTENNA
SPEAKER
FRONT R FRONT L SUR R SUR L
COAXIAL 75
FM AM
SPEAKER
DIGITAL IN
CENTER SUBWOOFER
DC5V
COAXIAL OPTICAL 0.7A MAX Y PB/CB PR/CR R AUDIO IN L
TV/VIDEO HDMI OUT DMPORT COMPONENT VIDEO OUT VIDEO OUT TV/VIDEO
After connecting the AC power cord (mains lead), the demonstration appears in the front panel display.
26GB
Step 3: Performing the LANGUAGE SETUP
OSD: ENGLISH
MENU: ENGLISH
Quick Setup
Getting Started
AUDIO: FRENCH
SUBTITLE: SPANISH
PORTUGUESE
Follow the Steps below to make the basic
adjustments for using the system.
Note
• When you connect the system and the TV with the
component video cord (not supplied) or HDMI cable
5 Press X/x to select a language.
(not supplied), you need to set the type of video The system displays the menu and subtitles
output for matching your TV. For details, see “Setting in the selected language.
the type of video output to match your TV” (page 29). 6 Press .
The Setup Display for selecting the aspect
"/1 ratio of the TV to be connected appears.
VIDEO SETUP
TV TYPE: 16:9
PROGRESSIVE (COMPONENT OUT): 16:9
4:3 OUTPUT: 4:3 LETTER BOX
BLACK LEVEL: 4:3 PAN SCAN
BLACK LEVEL (COMPONENT OUT): OFF
PAUSE MODE: AUTO
C/X/x/c,
DISPLAY
7 Press X/x to select the setting that
matches your TV type.
x If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
[16:9] (page 54)
1 Turn on the TV.
x If you have a 4:3 standard TV
2 Press [/1. [4:3 LETTER BOX] or [4:3 PAN SCAN]
Note (page 54)
• Make sure that the function is set to “DVD”
(page 30).
8 Press .
The Setup Display for selecting the speaker
3 Switch the input selector on your TV so formation appears.
that the signal from the system
appears on the TV screen. 9 Press C/c to select the speaker
formation image as the speakers are
[Press [ENTER] to run QUICK SETUP.]
actually positioned.
appears at the bottom of the TV screen. If
this message does not appear, recall the For details, see “Getting Optimal Surround
Quick Setup display (page 28) and perform Sound for a Room” (page 78).
again.
4 Press without inserting a disc.
SPEAKER FORMATION
27GB
10 Press . volume down. Give consideration to children
and neighbors.
11 Connect the calibration mic to the • Avoid being in the measurement area and
A.CAL MIC jack on the front panel.
Getting Started
AL M
IC 15 Press .
N/ A.C Quick Setup is finished. All connections
IO I
AUD and setup operations are complete.
28GB
4 Press X/x to select [QUICK], then press • [720 × 480p]**: The system outputs 720 ×
. 480p* video signals.
The Quick Setup display appears. * i: interlace, p: progressive
Getting Started
** Depending on the country model, [720 × 576p]
may appear.
Setting the type of video Note
output to match your TV • When “HDMI” lights up in the front panel display,
images other than [720 × 480p] or [720 × 576p] are
stretched vertically.
Depending on the connection of the TV
(page 18), select the type of video output of the Does your TV accept progressive
system. signals?
Progressive is the method for displaying TV
To select the type of video signal
images which reduces flickering and sharpens
output from the HDMI OUT jack the image. To use this method, you need to
When you connect the unit and the TV with the connect to a TV that accepts progressive signals.
HDMI cable, select the type of video signals
output from the HDMI OUT jack.
1 Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
For details, refer also to the operating
display.
instructions supplied with the TV/projector, etc.
1 Press FUNCTION +/– repeatedly until
2 Press DISPLAY while the system is
in stop mode.
“DVD” appears in the front panel
display. The Control Menu display appears on the
TV screen.
2 Press DISPLAY while the system is
in stop mode. 3 Press X/x to select [SETUP],
then press .
The Control Menu display appears on the
TV screen. The options for [SETUP] appear.
4 Press X/x to select [CUSTOM], then 5 Press X/x to select [VIDEO SETUP],
press . then press .
The Setup Display appears. The options for [VIDEO SETUP] appear.
5 Press X/x to select [HDMI SETUP], then 6 Press X/x to select [PROGRESSIVE
press . (COMPONENT OUT)], then press .
The options for [HDMI SETUP] appear. 7 Press X/x to select the desired setting,
then press .
6 Press X/x to select [HDMI
[OFF]: The system does not output
RESOLUTION], then press .
progressive signals. Select this setting
7 Press X/x to select the desired setting, when:
then press .
– your TV does not accept progressive
• [AUTO (1920 × 1080p)]: The system signals, or,
outputs the optimal video signal for the
– your TV is connected to jacks other than
connected TV.
the COMPONENT VIDEO OUT jacks.
• [1920 × 1080i]: The system outputs 1920
× 1080i* video signals.
• [1280 × 720p]: The system outputs 1280 ×
720p* video signals.
29GB
[ON]: The system outputs progressive
signals. Select this setting when: Step 4: Enjoying Sound
– your TV accepts progressive signals,
from all the Speakers
Getting Started
and,
– the TV is connected to the
COMPONENT VIDEO OUT jacks. You can enjoy DVD, TV, or VCR sound from
When you select [ON], the confirmation all the speakers in this system.
display appears. Follow the Steps below.
8 Press C/c to select [START].
The system outputs the progressive signal FUNCTION
for 5 seconds. Check that the screen is +/–
displayed correctly.
9 Press C/c to select [YES].
The system outputs the progressive signal.
When you select [NO], the system does not SYSTEM
output the progressive signal. MENU
X/x/c,
Function Source
“DVD” Disc that is played by the
system
“TUNER FM”/ FM/AM radio (page 61)
”TUNER AM”
“USB”* USB device (page 67)
“TV/VIDEO” TV (or the component that
is connected to the TV/
VIDEO jacks on the rear
panel)
“DMPORT”** DIGITAL MEDIA PORT
adapter (page 76)
“AUDIO” Portable audio source (that
is connected to the AUDIO
IN jack on the front panel)
30GB
* DAV-DZ270 only To prevent distortion, reduce the input level on
** DAV-HDZ278 only the unit.
Note 1 Press FUNCTION +/– repeatedly until
Getting Started
• When you use both the TV/VIDEO (AUDIO “TV/VIDEO” or “AUDIO” appears in the
IN) jacks (analog connection) and TV/VIDEO front panel display.
(COAXIAL or OPTICAL DIGITAL IN) jack
(digital connection) at the same time, the digital 2 Press SYSTEM MENU.
connection takes priority (DAV-HDZ278 only). 3 Press X/x repeatedly until
2 Press SYSTEM MENU. “ATTENUATE” appears in the front
panel display, then press or c.
3 Press X/x repeatedly until “DEC.
MODE” appears in the front panel 4 Press X/x to select a setting.
display, then press or c. • “ATT ON”: You can attenuate the input
4 Press X/x repeatedly until the level. The output level is changed.
decoding mode you want appears in • “ATT OFF”: Normal input level.
the front panel display. 5 Press .
When you want to output the TV sound or The setting is made.
stereo sound of a 2 channel source from the
six speakers, select the “PRO LOGIC,” 6 Press SYSTEM MENU.
“PLII MOVIE,” or “PLII MUSIC” The system menu turns off.
decoding mode.
For details, see page 32.
5 Press .
The setting is made.
6 Press SYSTEM MENU.
The system menu turns off.
Note
• Depending on your TV, you may need to turn off your
TV’s speaker to enjoy surround sound of the system.
Tip
• When listening to audio files using a portable audio
source, you can enhance the sound.
Press FUNCTION +/– to select “AUDIO.” Connect
the portable audio source. Select “A.F.D. STD” for
“DEC. MODE.”
To cancel, select other than “A.F.D. STD.”
31GB
Sound Adjustment
SYSTEM
MENU
X/x/c,
32GB
Display Decoding mode Effect
“PLII MOVIE” Dolby Pro Logic II Performs Pro Logic II movie mode decoding to the input signal and
MOVIE produces five full-bandwidth output channels from 2 channel sources.
This setting is ideal for watching videos of overdubbed or old movies.
This mode outputs sound from all the speakers and subwoofer. Sound
may not be output from all speakers depending on the source.
Sound Adjustment
“PLII MUSIC” Dolby Pro Logic II Performs Pro Logic II music mode decoding to the input signal and
MUSIC produces five full-bandwidth output channels from 2 channel sources.
This setting is ideal for normal stereo sources such as a CD.
This mode outputs sound from all the speakers and subwoofer. Sound
may not be output from all speakers depending on the source.
“2CH STEREO” 2 CHANNEL Outputs the sound from the front left and right speakers and
STEREO subwoofer. Multi channel surround formats are downmixed to 2
channels.
“HP 2CH” HEADPHONE Outputs the sound from headphone left and right. Multi channel
2 CHANNEL surround formats are downmixed to 2 channels.
STEREO
“HP VIRTUAL” HEADPHONE Outputs the sound as surround from headphone left and right. This
VIRTUAL mode is effective only when a multi channel source is played.
4 Press .
The setting is made.
5 Press SYSTEM MENU.
The system menu turns off.
To turn the surround effect off
Select “A.F.D. STD” or “2CH STEREO” for “DEC. MODE.”
Note
• When the input signal is multi channel source, “PRO LOGIC,” “PLII MOVIE,” and “PLII MUSIC” are canceled
and the multi channel source is output directly.
• When the bilingual broadcast sound is input, “PRO LOGIC,” “PLII MOVIE,” and “PLII MUSIC” are not effective.
• You cannot select the decoding mode when the unit is reading the files in the USB device or recording/copying
songs (DAV-DZ270 only).
• Depending on the input stream, the decoding mode may not by effective.
• When you select “A.F.D. MULTI,” the surround or stereo effect may not be effective. In this case, select “A.F.D.
STD,” “PRO LOGIC,” “PLII MOVIE,” or “PLII MUSIC.”
33GB
Selecting the Sound Enjoying Multiplex
Mode Broadcast Sound
You can select a suitable sound mode for movies (DUAL MONO)
or music. (DAV-HDZ278 only)
You can enjoy multiplex broadcast sound when
the system receives or plays the Dolby Digital
multiplex broadcast signal.
Note
• To receive the Dolby Digital signal, you need to
connect a TV or other component to the unit with an
SOUND optical or coaxial digital cord (page 18) and set the
MODE digital output mode of the TV or other component to
Dolby Digital.
AUDIO
34GB
Place one disc on the tray, and then press A.
Disc
Playing a Disc
Disc
Depending on the DVD VIDEO or VIDEO CD,
some operations may be different or restricted. Note
Refer to the operating instructions supplied with • When you play an 8 cm disc, place it on the
your disc. inner circle of the tray. Be careful that the disc is
not skewed on the inner circle of the tray.
Adjust the volume • Do not forcibly press the disc tray closed with
"/1 A H FUNCTION your finger, as this may cause malfunction.
• Do not place more than one disc on the tray.
6 Press H.
The system starts playback (continuous
play).
Disc tray Connect
headphones 7 Adjust the volume by using VOLUME +/
– on the remote or the VOLUME control
on the unit.
"/1
The volume level appears on the TV screen
FUNCTION and in the front panel display.
+/–
Note
• Depending on the system status, the volume level
may not appear on the TV screen.
• When you set the Control for HDMI function to on,
the TV that is connected to the system with an HDMI
MUTING cable (not supplied) can be sync-operated with the
system. For details, see “Using the Control for HDMI
STEP VOLUME +/–
Function for “BRAVIA” Sync” (page 64).
/ , ./>
/ Tip
H
/m/ • When you connect the system and TV with an HDMI
M/ x cable (not supplied), you can operate them simply,
X using the Control for HDMI function. For details, see
“Using the Control for HDMI Function for
1 Turn on your TV. “BRAVIA” Sync” (page 64).
35GB
– [CONTROL FOR HDMI] is set to [OFF] To Press
(page 64). Replay the previous (instant replay) during
scene (10 seconds playback.
To use the headphones before)7)
Connect the headphones to PHONES jack on the Briefly fast forward the (instant advance)
unit. The sound of the system is muted. current scene (30 during playback.
seconds after)8)
Other operations
1)Except for JPEG image files.
2)Scan speeds may differ with some discs.
To Press
3)
Stop x DVD VIDEO, DVD-R, DVD-RW, VIDEO CD only.
4)
Pause X Except for VIDEO CDs.
5)You cannot search for a still picture on a DVD-VR.
Resume play after pause X or H
6)
Go to the next chapter, > For a DATA CD/DATA DVD, this function works
track, or scene1) only for DivX video files (except for United
Kingdom and North American models).
Go back to the .
7)
preceding chapter, DVD VIDEO/DVD-RW/DVD-R only.
track, or scene1) The button can be used except for DivX video files
Turn off the sound MUTING. (except for United Kingdom and North American
temporarily models).
To cancel, press it again or
8)DVD VIDEO/DVD-RW/DVD-R/DVD+RW/
VOLUME + to adjust the
sound volume. DVD+R only.
The button can be used except for DivX video files
Stop play and remove A on the unit.
(except for United Kingdom and North American
the desired disc
models).
Locate a point quickly M/ or /m while
by playing a disc in fast playing a disc. Each time Note
forward or fast reverse you press M/ or / • You may not be able to use the instant replay or
(Scan)1)2) m during scan, the instant advance function with some scenes.
playback speed changes.
To return to normal speed,
press H. Actual speeds Displaying multi-angles and
may differ with some discs.
Watch frame by frame M/ or /m4)
subtitles
(Slow-motion Play)3) while the system is in pause
mode. Each time you press To change the angles
M/ or /m4)
during Slow-motion Play,
the playback speed If various angles (multi-angles) for a scene are
changes. Two speeds are recorded on a DVD VIDEO, you can change the
available. To return to viewing angle.
normal playback speed,
press H. Press ANGLE during playback to select the
desired angle.
Play one frame at a time STEP to go to the next
(Freeze Frame)3)5)6) frame while the system is in Note
pause mode. Press STEP • Depending on the DVD VIDEO, you may not be able
to go to the preceding to change the angle even if multi-angles are recorded
frame while the system is in on the DVD VIDEO.
pause mode (DVD VIDEO/
DVD-R/DVD-RW only).
To return to normal
playback, press H.
36GB
To display the subtitles When 4 digits are displayed, they indicate a
* * language code. See “Language Code List”
(page 102) to confirm which language the code
* Except for United Kingdom and North American represents. When the same language is
models. displayed two or more times, the DVD VIDEO
If subtitles are recorded on a disc, you can turn is recorded in multiple audio formats.
the subtitles on/off during playback. If
multilingual subtitles are recorded on the disc, x DVD-VR
you can change the subtitle language during The types of sound tracks recorded on a disc are
Disc
playback, or turn the subtitles on/off whenever displayed.
you want. Example:
• [1: MAIN] (main sound)
Press SUBTITLE during playback to select • [1: SUB] (sub sound)
the desired subtitle language.
• [1: MAIN+SUB] (main and sub sound)
Note • [2: MAIN]
• Depending on the DVD VIDEO, you may not be able • [2: SUB]
to change the subtitles even if multilingual subtitles
are recorded on the disc. You also may not be able to
• [2: MAIN+SUB]
turn them off. Note
• You can change the subtitles if the DivX video file • [2: MAIN], [2: SUB], and [2: MAIN+SUB] do not
has an “.AVI” or “.DIVX” extension and contains appear when one audio stream is recorded on the disc.
subtitle information within the same file (except for
United Kingdom and North American models). x VIDEO CD/CD/DATA CD (MP3 file)/DATA
DVD (MP3 file)
• [STEREO]: The standard stereo sound.
Changing the sound • [1/L]: The sound of the left channel
(monaural).
• [2/R]: The sound of the right channel
(monaural).
x DATA CD (DivX video file) /DATA DVD
When the system is playing a DVD VIDEO or
(DivX video file) (Except for United
DATA CD/DATA DVD (DivX video files*) Kingdom and North American models)
recorded in multiple audio formats (PCM, The choice of DATA CD or DATA DVD audio
Dolby Digital, MPEG audio, or DTS), you can signal formats differ, depending on the DivX
change the audio format. If the DVD VIDEO is video file contained on the disc. The format is
recorded with multilingual tracks, you can also shown in the display.
change the language.
With a VIDEO CD, CD, DATA CD, or DATA x Super VCD
DVD, you can select the sound from the right or • [1:STEREO]: The stereo sound of the audio
left channel and listen to the sound of the track 1.
selected channel through both the right and left • [1:1/L]: The sound of the left channel of the
speakers. audio track 1 (monaural).
You cannot change the sound for a Super Audio • [1:2/R]: The sound of the right channel of the
CD. audio track 1 (monaural).
* Except for United Kingdom and North American • [2:STEREO]: The stereo sound of the audio
models. track 2.
Press AUDIO repeatedly during playback to • [2:1/L]: The sound of the left channel of the
select the desired audio signal. audio track 2 (monaural).
x DVD VIDEO • [2:2/R]: The sound of the right channel of the
Depending on the DVD VIDEO, the choice of audio track 2 (monaural).
language varies.
37GB
Note x DATA CD (DivX video file)/DATA DVD
• While the system is playing a Super VCD on which (DivX video file) (Except for United
the audio track 2 is not recorded, no sound will come Kingdom and North American models)
out when you select [2:STEREO], [2:1/L], or [2:2/R].
Example:
MP3 audio
Checking the audio signal
format 1:MP3 128k
Bit rate
* *
38GB
To select a playback layer when 1 Start playing a VIDEO CD with PBC
playing a hybrid Super Audio CD functions.
Some Super Audio CDs consist of an HD layer The menu for your selection appears.
and a CD layer. You can select the playback
layer you want to listen to.
2 Select the item number you want using
the number buttons.
Note
• When the Super Audio CD does not have the HD
3 Press .
layer, you cannot select the playback layer. 4 Follow the instructions in the menu for
Disc
interactive operations.
1 Press DISPLAY while the system is
Refer to the operating instructions supplied
in stop mode.
with the disc, as the operating procedure
The Control Menu display appears on the
may differ depending on the VIDEO CD.
TV screen.
2 Press X/x to select [SUPER To go back to the menu
AUDIO CD/CD LAYER], then press . Press O RETURN.
The options for [SUPER AUDIO CD/CD Note
LAYER] appear. • Depending on the VIDEO CD, [Press ENTER] in
3 Press X/x to select the desired setting Step 3 may appear as [Press SELECT] in the
operating instructions supplied with the disc. In this
and press .
case, press H.
• [SUPER AUDIO CD]: You can play the
HD layer. Tip
When the system is playing a HD layer, • To play without using the PBC function, press ./
“SA-CD” lights up in the front panel > or the number buttons while the system is in stop
mode to select a track, then press H or . The
display
system starts playback. You cannot play still pictures
• [CD]: You can play the CD layer. such as a menu. To return to PBC playback, press x
When the system is playing a CD layer, twice, then press H.
“CD” lights up in the front panel display.
Note
• Each play mode function works only within the Resuming playback from the
selected layer or playback area. point where you stopped the disc
• When you select a CD layer, you cannot change a
playback area. (Resume Play)
• Super Audio CD audio signals are not output from the
HDMI OUT jack.
39GB
Note
• Depending on where you stop the disc, the system
may not resume playback from exactly the same
Using Play Mode
point.
• The point where you stopped playing may be cleared
when:
Creating your own program
– you eject the disc. (Program Play)
– the system enters standby mode (DATA CD/
DATA DVD only).
– you change or reset the settings on the Setup You can play the contents of a disc in the order
Display. you want by arranging the order of the tracks on
– you change the parental control level. the disc to create your own program. You can
– you change the function by pressing FUNCTION program up to 99 tracks.
+/–.
– you disconnect the AC power cord (mains lead). 1 Press DISPLAY.
• For a DVD-VR, VIDEO CD, Super Audio CD, CD, The Control Menu display appears on the
DATA CD, or DATA DVD, the system remembers TV screen.
the resume playback point for the current disc.
• Resume Play does not work during Program Play and
2 Press X/x to select [PROGRAM],
then press .
Shuffle Play.
• This function may not work properly with some The options for [PROGRAM] appear.
discs. 3 Press X/x to select [SET t], then
Tip
press .
• To play from the beginning of the disc, press x twice,
Total time of the programmed tracks
then press H.
PROGRAM 0: 00:00
To enjoy a disc that is played T
ALL CLEAR
before by resume playback 1. TRACK –– ––
2. TRACK –– 01
(Multi-disc Resume) 3. TRACK –– 02
4. TRACK –– 03
5. TRACK –– 04
6. TRACK –– 05
This system recalls the point where you stopped 7. TRACK –– 06
the disc the last time it was played and resumes
Tracks recorded on a disc
playback from that point the next time you insert
the same disc. When the resume playback
memory is full, the resume playback point for
4 Press c.
the earliest disc is deleted. The cursor moves to the track row [T] (in
To activate this function, set [MULTI-DISC this case, [01]).
RESUME] in [SYSTEM SETUP] to [ON]. For
PROGRAM 0: 00:00
details, see “[MULTI-DISC RESUME] (DVD T
VIDEO/VIDEO CD only)” (page 58). ALL CLEAR
1. TRACK –– ––
Note 2. TRACK –– 01
3. TRACK –– 02
• This system can store at least 10 resume playback 4. TRACK –– 03
points. 5. TRACK –– 04
6. TRACK –– 05
• If [MULTI-DISC RESUME] in [SYSTEM SETUP] 7. TRACK –– 06
is set to [OFF] (page 58), the resume point is cleared
when you change the function by pressing
FUNCTION +/–. 5 Select the track you want to program.
For example, select track [02].
Tip
• To play from the beginning of the disc, press x twice, Press X/x to select [02] under [T], then
then press H. press .
40GB
Selected track
To cancel all of the tracks in the
programmed order
PROGRAM 0: 03:51
T 1 Follow Steps 1 to 3 of “Creating your
ALL CLEAR own program.”
1. TRACK 02 ––
2. TRACK
3. TRACK
––
––
01
02
2 Press X and select [ALL CLEAR].
4. TRACK
5. TRACK
––
––
03
04 3 Press .
6. TRACK –– 05
–– 06
Disc
7. TRACK
41GB
4 Press . x DATA CD/DATA DVD
Shuffle Play starts. • [OFF]: Off.
• [DISC]: You can repeat all of the folders
To return to normal play on the disc.
Press CLEAR, or select [OFF] in Step 3. • [FOLDER]: You can repeat the current
folder.
To turn off the Control Menu • [TRACK] (MP3 files only): You can
display repeat the current file.
Press DISPLAY repeatedly until the Control • [FILE] (DivX video files only): You can
Menu display is turned off. repeat the current file (except for United
Note
Kingdom and North American models).
• You cannot use Shuffle Play with a VIDEO CD or 4 Press .
Super VCD with PBC playback.
The item is selected.
42GB
Searching/Selecting a Selecting [ORIGINAL] or [PLAY
LIST] on a DVD-VR
Disc
Using the DVD’s menu This function is only available for DVD-VRs
with a playlist created.
1
Disc
Press DISPLAY while the system is
in stop mode.
A DVD is divided into a lot of sections, which
The Control Menu display appears on the
make up a picture or music feature. These
TV screen.
sections are called “titles.” When you play a
DVD which contains several titles, you can 2 Press X/x to select [ORIGINAL/
select the title you want using DVD TOP PLAY LIST], then press .
MENU. The options for [ORIGINAL/PLAY LIST]
When you play a DVD that allows you to select appear.
items such as the language for the subtitles and
the language for the sound, select these items
3 Press X/x to select a setting.
using DVD MENU. • [PLAY LIST]: You can play the titles
created from [ORIGINAL] for editing.
1 Press DVD TOP MENU or DVD MENU.
• [ORIGINAL]: You can play the titles
The disc’s menu appears on the TV screen. originally recorded.
The contents of the menu vary depending
on the disc.
4 Press .
43GB
The number in parentheses indicates the 3 Input the time code using the number
total number of titles, chapters, tracks, buttons.
indexes, scenes, folders, or files. For example, to find the scene at 2 hours, 10
minutes, and 20 seconds after the
98( 99) beginning. Press 2, 1, 0, 2, 0 ([2:10:20]).
13( 99) DVD VIDEO
T 0: 03: 17
4 Press .
Note
• You cannot search for a scene on a DVD+RW using
the time code.
Selected row
3 Press .
[** (**)] changes to [– – (**)].
98( 99)
13( 99) DVD VIDEO
T 0: 03: 17
44GB
2 Press X/x to select a folder.
Playing MP3 Files/JPEG x To play MP3 files in a folder
Press H to start playing the selected
Image Files folder.
x To select a MP3 file
Press .
You can play the MP3 files or JPEG image files: The list of files contained in the folder
• which have the extension “.MP3” (MP3 file) appears.
Disc
or “.JPG”/“.JPEG” (JPEG image file)
• which conform to the DCF* image file format TRACK LIST
03 In the Middle of Nowher...
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by Japan 01_Geronimo_s_Cadillac
02_Riding_On_A_White_Swan
Electronics and Information Technology Industries 03_Give_Me_Peace_On_Earth
Association (JEITA). 04_Sweet_Little_Shella
05_Ten_Thousand_Lonely_Drums
Note 06_Lonely_Tears_In_Chinatown
07_In_Shaire
• The system will play any data with the extension
“.MP3,” “.JPG,” or “.JPEG” even if they are not in
MP3 or JPEG format. Playing these data may Press X/x to select a file and press .
generate a loud noise which could damage your The system starts playing the selected file.
speaker system. You can turn the file list off by pressing
• The system does not conform to audio in MP3PRO DVD MENU. Pressing DVD MENU again
format. will display the folder list.
• The system can recognize up to 200 folders, and will
not play any folders beyond the 200th. (Depending on To stop playback
the folder configuration, the number of folders that
Press x.
can be recognized by the system may decrease.)
• The system can recognize up to 150 MP3 files/JPEG To play the next or previous MP3
image files in a folder. file
• The system may take longer time to playback, when
progressing to the following folder or jump to other Press >/.. Note that you can select the
folder. next folder by continuing to press > after the
• The system may not play certain types of JPEG image last file on the current folder, but that you cannot
files (ex. a JPEG image file that is less than 8 (width) return to the previous folder by pressing ..
× 8 (height)). To return to the previous folder, select the folder
from the folder list.
45GB
return to the previous folder, select the folder
FOLDER LIST from the folder list.
01 Let's Talk About Love (1985)
02 1st Album (1986) To rotate a JPEG image file
03 In the Middle of Nowhere (1986)
04 Ready for Romance (1986) When a JPEG image file is displayed on the TV
05 In the Garden of Venus (1987)
06 Romantic Warriors (1987) screen, you can rotate the JPEG image file by 90
07 Back for Good (1988) degrees.
08 Alone (1999)
Press X/x while viewing a JPEG image file.
Press CLEAR to return to normal view.
2 Press X/x to select a folder. Note
x To play JPEG image files in a folder • You cannot rotate the JPEG image file when you set
[JPEG RESOLUTION] in [HDMI SETUP] to [(1920
Press H to start playing the selected
× 1080i) HD ] or [(1920 × 1080i) HD] (page 56).
folder.
x To select a JPEG image file by To stop playback
displaying the subscreens Press x.
Press PICTURE NAVI.
Images of JPEG image files in the folder
appear in 16 subscreens. Displaying the list of MP3
files/JPEG image files
1 2 3 4 1 Press DISPLAY during playback.
The Control Menu display appears on the
5 6 7 8
TV screen.
9 10 11 12 2 Press X/x to select
[BROWSING], then press .
13 14 15 16 The options for [BROWSING] appear.
Press C/X/x/c to select the JPEG image
file you want to view, then press .
3 Press X/x to select the desired list,
then press .
To return to normal screen, press O
• [FOLDER LIST]: The list of folders
RETURN.
appears. Follow Step 2 of “Selecting an
Note MP3 file or folder.”
• PICTURE NAVI does not work when you set • [PICTURE LIST]: Images of JPEG image
[MODE (MUSIC, IMAGE)] to [MUSIC]. files in the folder appear in 16 subscreens.
Tip
Follow Step 2 of “Selecting a JPEG image
• A scroll box is displayed at the right side of the file or folder.”
TV screen. To display the additional JPEG
image files, select the bottom JPEG image file
and press x. To return to the previous JPEG Playing MP3 files and JPEG
image file, select the top JPEG image file and
press X. image files as a slide show
To play the next or previous JPEG with sound
image file
You can play a slide show with sound by first
Press c/C when the Control Menu display is not placing both MP3 files and JPEG image files in
displayed. Note that you can select the next the same folder on a DATA CD or DATA DVD.
folder by continuing to press c after the last
image on the current folder, but that you cannot 1 Load a DATA CD or DATA DVD.
return to the previous folder by pressing C. To
46GB
2 Press DISPLAY while the system is The options for [INTERVAL] appear.
in stop mode.
The Control Menu display appears on the
3 Press X/x to select a setting.
• [NORMAL]: You can set to the standard
TV screen.
duration.
3 Press X/x to select [MODE • [FAST]: You can set the duration shorter
(MUSIC, IMAGE)], then press . than [NORMAL].
The options for [MODE (MUSIC, • [SLOW 1]: You can set the duration
IMAGE)] appear. longer than [NORMAL].
Disc
4 Press X/x to select a setting. • [SLOW 2]: You can set the duration
• [AUTO]: You can play both the JPEG longer than [SLOW 1].
image files and MP3 files in the same 4 Press .
folder as a slide show.
Note
• [MUSIC]: You can play only MP3 files • Some JPEG image files may take longer to display
continuously. than the option you selected. Especially progressive
• [IMAGE]: You can play only JPEG JPEG image files or JPEG image files of 3,000,000
image files as a slide show. pixels or more.
5 Press .
• Duration of interval depends on the [JPEG
RESOLUTION] setting in [HDMI SETUP]
6 Press DVD MENU. (page 55).
The list of folders recorded on the DATA
To select an effect for JPEG
CD or DATA DVD appears.
image files in the slide show
7 Press X/x to select the desired folder
1 Press DISPLAY twice.
and press H.
The system starts playing the selected The Control Menu display appears on the
folder. TV screen.
You can turn the folder list on/off by 2 Press X/x to select [EFFECT],
pressing DVD MENU repeatedly. then press .
Note
The options for [EFFECT] appear.
• If you set [MODE (MUSIC, IMAGE)] to [IMAGE] 3 Press X/x to select a setting.
on a disc that contains MP3 files only or [MUSIC] on
• [MODE 1]: The JPEG image file sweeps
a disc that contains JPEG image files only, you may
not be able to change the [MODE (MUSIC, in from top to bottom.
IMAGE)] setting. • [MODE 2]: The JPEG image file stretches
• PICTURE NAVI does not work when [MUSIC] is out from left to right of the TV screen.
selected. • [MODE 3]: The JPEG image file stretches
• If you play large MP3 file and JPEG image file at the out from the center of the TV screen.
same time, the sound may skip. Sony recommends • [MODE 4]: The JPEG image files
that you set the MP3 bit rate to 128 kbps or lower randomly cycle through the effects.
when creating the file. If the sound still skips, reduce
the size of the JPEG image file.
• [MODE 5]: The next JPEG image file
slides over the previous image.
To select the slide show duration • [OFF]: Off.
of JPEG image files 4 Press .
1 Press DISPLAY twice. Note
The Control Menu display appears on the • The [EFFECT] setting is not effective when you set
TV screen. [JPEG RESOLUTION] in [HDMI SETUP] to [(1920
× 1080i) HD ] or [(1920 × 1080i) HD] (page 56).
2 Press X/x to select [INTERVAL],
then press .
47GB
“.AVI,” or “.DIVX.” The system will not play
Enjoying DivX® Videos files with the extension “.AVI” or “.DIVX” if
they do not contain a DivX video.
Tip
(Except for United Kingdom and North • For details about playable MP3 audio tracks or JPEG
image files on a DATA CD or DATA DVD, see
American models)
“Playable Discs” (page 6).
Note
• The system may not play a DivX video file when the
About DivX video files file has been combined from two or more DivX video
files.
DivX® is a video file compression technology,
• The system cannot play a DivX video file of size
developed by DivX, Inc. This product is an more than 720 (width) × 576 (height) or 2GB.
official DivX® Certified product. • Depending on the DivX video file, sound may skip or
You can play a DATA CD or DATA DVD that not match the pictures on the TV screen.
contains DivX® video files. • The system cannot play some DivX video files that
are longer than 3 hours.
A DATA CD or DATA DVD that the
• Depending on the DivX video file, the picture may
system can play pause or be unclear. In which case, it is recommended
Playback of a DATA CD (CD-ROM/CD-R/CD- that you create the file at a lower bit rate. If the sound
RW) or DATA DVD (DVD-ROM/DVD-R/ is still noisy, MP3 is the recommended audio format.
DVD-RW/DVD+R/DVD+RW) on this system Note, however, this system does not conform to
is subject to certain conditions: WMA (Windows Media Audio) format for playing
DivX files.
– With a DATA CD/DATA DVD that contains • Because of the compression technology used for
DivX video files in addition to MP3 audio DivX video files, it may take some time after you
tracks or JPEG image files, the system plays press H for the picture to appear.
only the DivX video files.
However, this system only plays a DATA CD of
format ISO 9660 Level 1/Level 2 or Joliet, and a Selecting a folder
DATA DVD of Universal Disk Format (UDF).
Refer to the operating instructions supplied with 1 Press DVD MENU.
the disc drives and the recording software (not A list of folders on the disc appears. Only
supplied) for details on the recording format. folders that contain DivX video files are
About playback order of data on a listed.
DATA CD or DATA DVD
FOLDER LIST
Note that the playback order may not be
SUMMER 2003
applicable, depending on the software used for NEW YEAR'S DAY
MY FAVOURITES
creating the DivX video file, or if there are more
than 200 folders and 150 DivX video files in
each folder.
Note
• The system may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write 2 Press X/x to select the folder you want
format. to play.
DivX video files that the system 3 Press H.
can play The system starts playing the selected
The system can play data that is recorded in folder.
DivX format, and which has the extension
48GB
To select DivX video files, see “Selecting a .. To return to the previous folder, select it
DivX video file” (page 49). from the folder list.
Disc
– when the disc tray is opened.
To stop playback
Press x.
FILE LIST
MY FAVOURITES
HAWAII 2004
VENUS
49GB
Adjusting the Delay Restricting Playback of
Between the Picture and the Disc
Sound [PARENTAL CONTROL]
[A/V SYNC]
* * Playback of some DVD VIDEOs can be limited
* Except for United Kingdom and North American according to a predetermined level such as the
models age of the users. Scenes may be blocked or
replaced with different scenes.
When the sound does not match the pictures on You can set the playback restriction by
the TV screen, you can adjust the delay between registering a password. When you set the
the picture and sound. [PARENTAL CONTROL] function to on, you
need to enter the password to play restricted
1 Press DISPLAY.
discs.
The Control Menu display appears on the
TV screen. 1 Press FUNCTION +/– repeatedly until
“DVD” appears in the front panel
2 Press X/x to select [A/V SYNC], display.
then press .
The options for [A/V SYNC] appear.
2 Press DISPLAY while the system is
in stop mode.
3 Press X/x to select a setting. The Control Menu display appears on the
• [OFF]: Off. TV screen.
• [ON]: You can adjust the difference
between picture and sound.
3 Press X/x to select [SETUP],
then press .
4 Press . The options for [SETUP] appear.
Note 4 Press X/x to select [CUSTOM], then
• Depending on the input stream, [A/V SYNC] may not press .
be effective. The Setup Display appears.
5 Press X/x to select [SYSTEM SETUP],
then press .
The options for [SYSTEM SETUP] appear.
6 Press X/x to select [PARENTAL
CONTROL t], then press .
x If you have not entered a password
The display for registering a new password
appears.
PARENTAL CONTROL
50GB
Enter a 4-digit password using the number To turn off the [PARENTAL
buttons, then press . CONTROL] function
The display for confirming the password Set [LEVEL] to [OFF] in Step 11.
appears.
To play a disc for which
x When you have already registered a
password [PARENTAL CONTROL] is set
The display for entering the password 1 Load the disc and press H.
appears.
The display for entering your password
Disc
7 Enter or re-enter your 4-digit password appears.
using the number buttons, then press
.
2 Enter your 4-digit password using the
number buttons, then press .
The display for setting the playback
The system starts playback.
limitation level appears.
Note
PARENTAL CONTROL • When you play discs which do not have the
[PARENTAL CONTROL] function, playback
LEVEL: OFF cannot be limited on this system.
STANDARD: USA • Depending on the disc, you may be asked to change
CHANGE PASSWORD:
the parental control level while playing the disc. In
this case, enter your password, then change the level.
If the Resume Play mode is canceled, the level returns
to the previous level.
51GB
5 Press X/x to select [SYSTEM SETUP],
then press .
Using the Setup Display
The options for [SYSTEM SETUP] appear.
6 Press X/x to select [PARENTAL You can make various adjustments of items such
CONTROL t], then press . as picture and sound.
Displayed items vary depending on the country
The display for entering the password
model.
appears.
7 Enter your 4-digit password using the
Note
• Playback settings stored in the disc take priority over
number buttons, then press .
the Setup Display settings and not all the functions
8 Press X/x to select [CHANGE described may work.
PASSWORD t], then press .
1 Press FUNCTION +/– repeatedly until
9 Enter your 4-digit password using the “DVD” appears in the front panel
number buttons, then press . display.
10 Enter a new 4-digit password using the 2 Press DISPLAY while the system is
number buttons, then press . in stop mode.
11 To confirm your password, re-enter it The Control Menu display appears on the
using the number buttons, then press TV screen.
. 3 Press X/x to select [SETUP],
If you make a mistake entering then press .
your password The options for [SETUP] appear.
Press C before you press , then input the 4 Press X/x to select [CUSTOM], then
correct number. press .
The Setup Display appears.
5 Press X/x to select the setup item, then
press .
• [LANGUAGE SETUP] (page 53)
• [VIDEO SETUP] (page 54)
• [HDMI SETUP] (page 55)
• [AUDIO SETUP] (page 57)
• [SYSTEM SETUP] (page 57)
• [SPEAKER SETUP] (page 58)
VIDEO SETUP
TV TYPE: 16:9
PROGRESSIVE (COMPONENT OUT): OFF
4:3 OUTPUT: FULL
BLACK LEVEL: ON
BLACK LEVEL (COMPONENT OUT): OFF
PAUSE MODE: AUTO
Setup items
52GB
6 Press X/x to select an item, then press
. Setting the display or sound
The options for the selected item appear. track language
Example: [TV TYPE]
[LANGUAGE SETUP]
VIDEO SETUP
TV TYPE: 16:9
PROGRESSIVE (COMPONENT OUT): 16:9
OFF Set various languages for the on-screen display
4:3 OUTPUT: 4:3 LETTERFULL
BOX or sound track.
BLACK LEVEL: AUTO
4:3 PAN SCAN
Disc
BLACK LEVEL (COMPONENT OUT): OFF
PAUSE MODE: AUTO LANGUAGE SETUP
OSD: ENGLISH
Options MENU: ENGLISH
AUDIO: ORIGINAL
SUBTITLE: AUDIO FOLLOW
Tip
• If you select [OTHERS t] in [MENU], [AUDIO],
and [SUBTITLE], select and enter a language code
from “Language Code List” (page 102) using the
number buttons.
53GB
Settings for the display x [PROGRESSIVE (COMPONENT OUT)]
You can set the progressive signal that is output
[VIDEO SETUP] from the COMPONENT VIDEO OUT jacks to
on/off. For details, see “Does your TV accept
Select settings according to the TV to be progressive signals?” (page 29).
connected.
[OFF]: The system outputs interlace signals.
VIDEO SETUP [ON]: The system outputs progressive signals.
TV TYPE: 16:9
PROGRESSIVE (COMPONENT OUT): OFF
When you select [ON], follow the Steps below.
4:3 OUTPUT:
BLACK LEVEL:
FULL
ON 1 Select [ON], then press .
BLACK LEVEL (COMPONENT OUT): OFF
PAUSE MODE: AUTO
The confirmation display appears.
2 Press C/c to select [START].
The system outputs the progressive signal
for 5 seconds. Check that the screen is
displayed correctly.
x [TV TYPE]
You can select the aspect ratio of the connected 3 Press C/c to select [YES].
TV. The system outputs the progressive signal.
If you select [NO], the system will not
[16:9]: Select this when you connect a wide- output the progressive signal.
screen TV or a TV with a wide mode function.
Note
• [PROGRESSIVE (COMPONENT OUT)] is
effective only when you connect the unit and TV with
a component video cord (page 18).
x [4:3 OUTPUT]
[4:3 LETTER BOX]: Select this when you
When you use a 16:9 aspect ratio TV, you can
connect a 4:3 screen TV. Displays a wide picture
adjust the aspect ratio to watch 4:3 aspect ratio
with bands on the upper and lower portions of
signals. If you can change the aspect ratio on
the TV screen.
your TV, change the setting on your TV, not the
system.
54GB
[AUTO]: The picture, including subjects that
x [COLOR SYSTEM (VIDEO CD)] move dynamically, is output with no jitter.
(Asian, Australian, and Middle Eastern Normally select this position.
models only) [FRAME]: The picture, including subjects that
You can select the color system when you play a do not move dynamically, is output in high
VIDEO CD. resolution.
Disc
your TV uses a DUAL system, select [AUTO].
[HDMI SETUP]
[PAL]: The system changes the video signal of
an NTSC disc and outputs it in the PAL system.
[NTSC]: The system changes the video signal of
HDMI SETUP
a PAL disc and outputs it in the NTSC system. HDMI RESOLUTION: AUTO(1920x1080P)
CONTROL FOR HDMI: OFF
Note VOLUME LIMIT: LEVEL2
• You cannot change the color system of the disc itself. YCBCR/RGB(HDMI): YCBCR
AUDIO(HDMI): OFF
• You can change the color system of this system JPEG RESOLUTION: HD
according to the connected TV (page 20).
x [BLACK LEVEL]
(North American, Mexican, and Latin
x [HDMI RESOLUTION]
American models only)
You can select the type of video signal that is
You can select the black level (setup level) for
output from the HDMI OUT jack. For details,
the video signals output from the jacks other
see “To select the type of video signal output
than COMPONENT VIDEO OUT/HDMI OUT.
from the HDMI OUT jack” (page 29).
[ON]: The standard level.
[AUTO (1920 × 1080p)]: The system outputs
[OFF]: You can lower the standard black level.
the optimal video signal for the connected TV.
Use this when the picture becomes too white.
[1920 × 1080i]: The system outputs 1920 ×
1080i* video signals.
x [BLACK LEVEL (COMPONENT OUT)] [1280 × 720p]: The system outputs 1280 ×
(North American, Mexican, and Latin 720p* video signals.
American models only) [720 × 480p]**: The system outputs 720 ×
You can select the black level (setup level) for 480p* video signals.
the video signals output from the
COMPONENT VIDEO OUT jacks. * i: interlace, p: progressive
You cannot select this and the setting is not ** Depending on the country model, [720 × 576p] may
effective when the system outputs progressive appear.
signal.
Note
• When “HDMI” lights up in the front panel display,
[OFF]: You can set the black level of the output images other than [720 × 480p] or [720 × 576p] are
signal to the standard level. stretched vertically.
[ON]: You can raise the standard black level.
Use this when the picture becomes too black. x [CONTROL FOR HDMI]
You can set the [CONTROL FOR HDMI]
x [PAUSE MODE] (DVD VIDEO/DVD-R/ function to on/off. This function is available
DVD-RW only) when you connect the system and TV with an
You can select the picture in pause mode. HDMI cable. For details, see “Using the Control
55GB
for HDMI Function for “BRAVIA” Sync” [ON]: The system outputs audio signals by
(page 64). converting Dolby Digital, DTS, or 96 kHz/24 bit
PCM signals to 48 kHz/16 bit PCM.
[OFF]: Off.
Note
[ON]: On. You can operate mutually between • When you connect the unit and TV with an HDMI
components that are connected with an HDMI cable and [ON] is selected, [AUDIO DRC], [A/V
cable. SYNC], DYNAMIC BASS, “DEC. MODE,” and
sound mode are not applied to the sound that is output
Note
from the TV.
• When you set to [ON] without the HDMI connection
of the TV, [Please verify the HDMI connection.] • When you set the function to other than “DVD,” the
appears and you cannot set to [ON]. system does not output the sound from the HDMI
OUT jack even if you set [AUDIO (HDMI)] to [ON].
x [VOLUME LIMIT]
If you change the output method of the TV to the x [JPEG RESOLUTION]
system speaker on the TV menu or by pressing You can select the resolution of JPEG image
THEATER/THEATRE*, the System Audio files output from the HDMI OUT jack.
Control (page 66) is activated and loud sound
may be output depending on the volume level of [SD ]: The system outputs standard
the system. You can prevent this by limiting the resolution with a black frame.
maximum level of the volume. [HD ]: The system outputs HD resolution
* The button name differs depending on the area. with a black frame.
[HD]: The system outputs the HD resolution
[LEVEL3]: Maximum volume level is set to 10. without a black frame.
[LEVEL2]: Maximum volume level is set to 15. [(1920 × 1080i) HD ]: The system outputs
[LEVEL1]: Maximum volume level is set to 20. full size HD resolution with a black frame.
[OFF]: Off. [(1920 × 1080i) HD]: The system outputs full
size HD resolution without a black frame.
Note
Note
• This function is available only when [CONTROL
FOR HDMI] is set to [ON]. • [JPEG RESOLUTION] is effective only when you
set [TV TYPE] in [VIDEO SETUP] to [16:9], and
you set [HDMI RESOLUTION] in [HDMI SETUP]
x [YCBCR/RGB (HDMI)] to other than [720 × 480p] or [720 × 576p].
You can select the type of HDMI signal output • You can select [(1920 × 1080i) HD ] or [(1920 ×
from HDMI OUT jack. 1080i) HD] only when you set [HDMI
RESOLUTION] in [HDMI SETUP] to [1920 ×
[YCBCR]: The system outputs YCBCR signals. 1080i].
[RGB]: The system outputs RGB signals. • If you select [(1920 × 1080i) HD ] or [(1920 ×
1080i) HD], next image appears after black flame.
Note
• HDMI signal will stop momentarily when:
• If the playback picture becomes distorted, set
– The system is loading or unloading a DATA CD or
[YCBCR] to [RGB].
DATA DVD disc.
• If the HDMI OUT jack is connected to a component
– You connect or remove a USB device (DAV-
with a DVI jack, [RGB] signals will be automatically
DZ270 only).
output even when you select [YCBCR].
x [AUDIO (HDMI)]
You can select the audio output status from the
HDMI OUT jack.
56GB
Note
Settings for the audio • When you set the item to [AUTO], the language may
change. The [TRACK SELECTION] setting has
[AUDIO SETUP] higher priority than the [AUDIO] settings in
[LANGUAGE SETUP] (page 53). (Depending on
the disc, this function may not work.)
AUDIO SETUP • If PCM, DTS, Dolby Digital sound, and MPEG audio
SPEAKER FORMATION:
AUTO CALIBRATION: have the same number of channels, the system selects
AUDIO DRC: OFF PCM, DTS, Dolby Digital sound, and MPEG audio in
Disc
TRACK SELECTION: OFF this order.
Other Settings
[SYSTEM SETUP]
x [SPEAKER FORMATION]
You can select the position of the speakers for
the better surround sound. For details, see SYSTEM SETUP
SCREEN SAVER: ON
“Getting Optimal Surround Sound for a Room” BACKGROUND: JACKET PICTURE
PARENTAL CONTROL:
(page 78). DivX: Registration Code
MULTI-DISC RESUME: ON
RESET:
x [AUTO CALIBRATION]
You can calibrate the appropriate settings
automatically. For details, see “Calibrating the
Appropriate Settings Automatically” (page 79).
x [SCREEN SAVER]
x [AUDIO DRC] (DVD VIDEO only) You can reduce the display device damages
You can compress the dynamic range of the (ghosting). Press any button (e.g., H button) to
sound track. [AUDIO DRC] is useful for cancel the screen saver.
watching movies at low volume late at night.
[ON]: The screen saver image appears when you
[OFF]: No compression of dynamic range. leave the system in pause or stop mode for 15
[STANDARD]: The system reproduces the minutes, or when you play back a Super Audio
sound track with the kind of dynamic range that CD, CD, DATA CD (MP3 file), or DATA DVD
the recording engineer intended. (MP3 file) for more than 15 minutes.
[MAX]: The system compresses dynamic range [OFF]: Off.
fully.
Note
x [BACKGROUND]
• [AUDIO DRC] works only for Dolby Digital. You can select the background color or picture
on the TV screen in stop mode or while playing
a CD, DATA CD (MP3 file), or DATA DVD
x [TRACK SELECTION] (DVD VIDEO only)
(MP3 file).
You can give the sound track which contains the
highest number of channels priority when you
[JACKET PICTURE]: The jacket picture (still
play a DVD VIDEO on which multiple audio
picture) appears, but only when the jacket
formats (PCM, DTS, Dolby Digital, or MPEG
picture is already recorded on the disc (CD-
audio) are recorded.
EXTRA, etc.). If the disc does not contain a
jacket picture, the [GRAPHICS] picture
[OFF]: Off.
appears.
[AUTO]: The system selects the sound track
[GRAPHICS]: A preset picture stored in the
automatically according to the priority.
system appears.
57GB
[BLUE]: The background is blue.
[BLACK]: The background is black. SPEAKER SETUP
CONNECTION:
DISTANCE(FRONT):
DISTANCE(SURROUND):
x [PARENTAL CONTROL] LEVEL(FRONT):
You can set the playback restrictions. For LEVEL(SURROUND):
TEST TONE
FRONT: YES
details, see “Restricting Playback of the Disc” CENTER: YES
(page 50). SURROUND: YES
SUBWOOFER: YES
x [DivX]
x [CONNECTION]
(Except for United Kingdom and North
American models)
If you do not connect center or surround
You can display the registration code for this speakers, set the parameters for [CENTER] and
system. [SURROUND]. Since the front speaker and
For more information, go to subwoofer setting is fixed, you cannot change
http://www.divx.com on the Internet. them.
[FRONT]
x [MULTI-DISC RESUME] (DVD VIDEO/ [YES]
VIDEO CD only) [CENTER]
You can set the [MULTI-DISC RESUME] [YES]: Normally select this.
function to on/off. [NONE]: Select this if no center speaker is used.
58GB
[L/R] 3.0 m/10 ft2)3): Set the surround speaker
distance (up to 5.0 meters (16 ft) closer to the
front speakers).
1)0.0 to 6.9 meters for North American models.
2)When you perform the Quick Setup (page 27), the
default settings are changed.
3)
This item appears when you set [SURROUND] to
A [YES] in the [CONNECTION] setting.
Disc
Note
• If all front and surround speakers are not placed at an
equal distance from your listening position, set the
distance according to the closest speaker.
• Do not place the surround speakers farther away from
your listening position than the front speakers.
[L/R] 3.0 m/10 ft3): Set the front speaker • Depending on the input stream, the [DISTANCE]
distance. setting may not be effective.
[CENTER] 3.0 m/10 ft3)4): Set the center speaker
distance (up to 1.6 meters (5 ft) closer to the x [LEVEL (FRONT)]
front speakers). You can adjust the sound level of the front
1)
0.9 to 6.9 meters for North American models.
speakers, center speaker, and subwoofer. Be
2)
sure to set [TEST TONE] to [ON] for easy
0.0 to 6.9 meters for North American models.
adjustment.
3)When you perform the Quick Setup (page 27), the
default settings are changed. [L/R] 0.0 dB: Set the front speaker level.
4)This item appears when you set [CENTER] to [YES] [CENTER] 0.0 dB*: Set the center speaker
in the [CONNECTION] setting. level.
[SUBWOOFER] +2.0 dB: Set the subwoofer
x [DISTANCE (SURROUND)] level.
When you move the surround speakers, be sure * This item appears when you set [CENTER] to
to set the parameters of the distance (B) from [YES] in the [CONNECTION] setting.
the listening position to the speakers.
You can set the parameters from 0.0 to 7.0 x [LEVEL (SURROUND)]
meters1) (0 to 23 ft). You can adjust the sound level of the surround
speakers. Be sure to set [TEST TONE] to [ON]
for easy adjustment.
B x [TEST TONE]
The speakers will emit a test tone to adjust
[LEVEL (FRONT)] and [LEVEL
(SURROUND)].
59GB
test tone is emitted from each speaker in
sequence.
Adjust the sound level as follows.
1 Set the [TEST TONE] to [ON].
2 Press C/X/x/c repeatedly to select the
desired speaker and the level.
3 Press .
4 Repeat Steps 1 to 3.
5 Press C/X/x/c repeatedly to set [TEST
TONE] to [OFF] after adjusting the
speaker level.
Note
• The test tone signals are not output from the HDMI
OUT jack.
Tip
• To adjust the volume of all the speakers at one time,
turn the VOLUME control on the unit, or press
VOLUME +/– on the remote.
• To return to the default setting when changing a
setting, select the item, then press CLEAR. Note that
only the [CONNECTION] setting does not return to
the default setting.
60GB
Tip
• You can select the preset number directly by
Tuner pressing the number buttons.
7 Press .
Presetting Radio “COMPLETE” appears in the front panel
Stations display, and the station is stored.
8 Repeat Steps 2 to 7 to store other
You can preset 20 FM stations, and 10 AM stations.
stations. Before tuning, make sure to turn down
the volume to minimum.
9 Press SYSTEM MENU.
The system menu turns off.
Tuner
Tip
• You can operate the tuner function by observing the To change the preset number
following display on the TV screen. Restart from Step 2.
Current station To change the AM tuning interval
Current band and preset number (except for Russian and Middle
Eastern models)
FM
The AM tuning interval can be set to either
FM 10 : 88.00 MHz 10 kHz or 9 kHz.
SONY RADIO To change the AM tuning interval, first tune in
any AM station, then turn off the system by
pressing "/1 on the unit. While holding down
Station name
> on the unit, press "/1 on the unit to turn on
1 Press FUNCTION +/– repeatedly until the power. If you change the interval, AM preset
“TUNER FM” or “TUNER AM” appears stations will be erased.
in the front panel display. To reset the interval, repeat the same procedure.
2 Press and hold TUNING +/– until the
auto scanning starts.
Scanning stops when the system tunes in a
station. “TUNED” and “ST” (for stereo
program) appear in the front panel display.
3 Press SYSTEM MENU.
4 Press X/x repeatedly until “MEMORY”
appears in the front panel display.
5 Press or c.
A preset number appears in the front panel
display.
61GB
If an FM program is noisy
Listening to the Radio If an FM program is noisy, you can select
monaural reception. There will be no stereo
Preset radio stations in the system’s memory effect, but reception will improve.
first (see “Presetting Radio Stations” (page 61)).
1 Press SYSTEM MENU.
1 Press FUNCTION +/– repeatedly until
2 Press X/x repeatedly until “FM MODE”
“TUNER FM” or “TUNER AM” appears
appears in the front panel display.
in the front panel display.
The last received station is tuned in.
2 Press PRESET +/– repeatedly to select
the preset station.
3 Press or c.
Each time you press the button, the system
tunes in one preset station. 4 Press X/x to select “MONO.”
• “STEREO”: Stereo reception.
Tip
• You can select the preset station number directly • “MONO”: Monaural reception.
by pressing the number buttons. 5 Press .
3 Adjust the volume by pressing The setting is made.
VOLUME +/–.
6 Press SYSTEM MENU.
To turn off the radio The system menu turns off.
Press "/1.
To listen to radio stations when The last received station is tuned in.
you know the frequencies 2 Press PRESET +/– repeatedly to select
the preset station you want to create an
1 Press FUNCTION +/– repeatedly until index name for.
“TUNER FM” or “TUNER AM” appears
in the front panel display. 3 Press SYSTEM MENU.
62GB
x “TUNER AM”
When the station name is set
1 Station name
You can input letters, numbers, and other
Ex. “SONY RADIO”
symbols for a radio station.
2 Frequency
If you make a mistake Ex. “AM1 576”
Press C/c repeatedly until the character to When the station name is not set:
be changed flashes, then press X/x to select 1 Frequency
the desired character. Ex. “AM1 576”
To erase the character, press C/c
Note
Tuner
repeatedly until the character to be erased • The system returns to the original display when
flashes, then press CLEAR. several seconds has elapsed.
7 Press .
“COMPLETE” appears in the front panel
display, and the station name is stored.
8 Press SYSTEM MENU.
The system menu turns off.
63GB
Note
• Depending on the connected component, the Control
Control for HDMI/External Audio for HDMI function may not work. Refer to the
Device operating instructions supplied with the component.
• The Control for HDMI function may not work if you
connect a component other than Sony, even if the
Using the Control for component is compatible with the Control for HDMI
function.
HDMI Function for
“BRAVIA” Sync Preparing for the Control for
This function is available on TVs with the HDMI function
“BRAVIA” Sync function only.
By connecting Sony components that are (Control for HDMI - Easy Setting)
compatible with the Control for HDMI function The system is compatible with the Control for
with an HDMI cable (not supplied), operation is HDMI - Easy Setting function. If the TV is
simplified as below: compatible with the Control for HDMI - Easy
– Theater/Theatre Mode (page 65) Setting function, you can set the system’s
– One-Touch Play (page 65) [CONTROL FOR HDMI] function
automatically by setting the TV. For details,
– System Power Off (page 66)
refer to the operating instructions of the TV.
– System Audio Control (page 66)
– Volume Limit (page 66) If the TV is not compatible with the Control for
HDMI - Easy Setting function, set the Control
Control for HDMI is a mutual control function for HDMI function of the system and TV
standard used by CEC (Consumer Electronics manually.
Control) for HDMI (High-Definition
Note
Multimedia Interface).
• Displayed items vary depending on the country
model.
The Control for HDMI function will not work in
the following cases: 1 Make sure that the system and the TV
are connected with an HDMI cable.
– When you connect this system to a
component which is not compatible with the 2 Turn on the TV and press [/1 to turn on
Control for HDMI function. the system.
– A component does not have an HDMI jack. 3 Switch the input selector on your TV so
that the signal from the system through
There are convenient buttons on the system’s the HDMI input appears on the TV
remote for operating the TV, such as screen.
THEATER/THEATRE*, ONE-TOUCH
PLAY, TV [/1. For details, see “Controlling the
4 Set the Control for HDMI function of the
system and TV.
TV with the Supplied Remote” (page 80) and
For details of the setting of the system, see
refer to the operating instructions of the TV.
* The button name differs depending on the area. the following Steps. For details of the
setting of the TV, refer to the operating
instructions of the TV (depending on the
ONE-TOUCH TV
THEATER PLAY
TV, the default setting of the Control for
BRAVIA Sync HDMI function is set to off).
64GB
To set the [CONTROL FOR HDMI]
function to on/off Watching DVD by a single
1 Press FUNCTION +/– repeatedly until button press
“DVD” appears in the front panel
display. (One-Touch Play)
By only pressing ONE-TOUCH PLAY, the TV
2 Press DISPLAY while the system is
turns on, the TV is set for DVD input mode, and
in stop mode.
the system starts playing a disc automatically.
The Control Menu display appears on the
TV screen. The One-Touch Play also works when:
3 Press X/x to select [SETUP], – You press A while the disc tray is opened and
then press . H appears in the front panel display.
The options for [SETUP] appear. – You close the disc tray by pressing the disc
(Theater/Theatre Mode)
Note
If your TV is compatible with the Theater/ • Make sure the HDMI connection is correct, and set
Theatre Mode, you can enjoy optimal image the [CONTROL FOR HDMI] to [ON].
suited for movies and the sound is output from • Depending on the TV, the beginning of the content
the system’s speaker automatically by pressing may not be played back.
THEATER/THEATRE*. • Depending on the disc, playback may take a while to
* The button name differs depending on the area. start.
65GB
You can also operate the System Audio Control
Turning the system off in sync function from the TV menu. For details, refer to
the operating instructions of the TV.
with the TV
Note
(System Power Off) • If the TV is turned on before turning on the system,
When you turn the TV off by using the POWER TV sound will not be output for a moment.
button on the TV’s remote or TV [/1 on the • While the TV is in PAP (picture and picture) mode,
system’s remote, the system turns off the System Audio Control function will not work.
When the TV exits PAP mode, the output method of
automatically.
the TV returns to the one before PAP mode.
Note • If you select a TV program during DVD playback
• Before using the System Power Off function, set the with the system, the “TV/VIDEO” function is
function for TV power. For details, refer to the automatically set to output TV sound.
operating instructions of the TV. • When you activate One-Touch Play during watching
• Depending on the status of the system (ex. while TV, the System Audio Control function is activated
other than “DVD” or “TV/VIDEO” function, or and the TV sound is muted.
playing a CD), the system may not turn off • While recording songs on an audio CD into a USB
automatically. device, the System Audio Control function will not
work (DAV-DZ270 only).
66GB
2 Connect a USB device (digital music
Playing Back Audio player or USB storage media) to the
(USB) port.
Files/JPEG Image Files When you connect the USB device,
“READING” appears in the front panel
of a USB Device display until the system reads all data of the
USB device.
(DAV-DZ270 only)
Note
You can play audio files (MP3/WMA/AAC • When you connect the USB device, make sure that
files)/JPEG image files stored in a USB device the direction of the jack is correct.
such as the digital music player or USB storage • Do not forcibly insert the USB device, as this may
media (not supplied) by connecting the USB cause the device to be damaged.
device to the unit. • Do not connect other device or objects besides the
For a list of USB devices that can be connected USB device.
67GB
• Some USB devices cannot be played back on
the system depending on the file format. Selecting an audio file or
• The system can play back to a depth of 8 folder
folders only.
• The system may not be able to play an audio 1 Press FUNCTION +/– repeatedly until
file depending on the kind of file. “USB” appears in the front panel
• When the USB device is inserted, the system display.
reads all the files on the USB device. If there
are many folders or files on the USB device, it
2 Press DISPLAY while the system is
in stop mode.
may take a long time to finish reading the USB
The Control Menu display appears on the
device.
TV screen.
• Do not connect the system and the USB device
through a USB hub. 3 Press X/x to select [MODE
• With some connected USB devices, after an (MUSIC, IMAGE)], then press .
operation is performed, there may be a delay The options for [MODE (MUSIC,
before it is performed by this system. IMAGE)] appear.
• If the system is turned off during Resume Play 4 Press X/x to select [MUSIC].
mode, when the system is turned on again
playback starts from the beginning of the audio 5 Press .
file that was in Resume Play mode. 6 Press DVD MENU.
• This system does not necessarily support all The folders recorded on the USB device
the functions provided in a connected USB appear. When a folder is being played, its
device. title is shaded.
• Files recorded by a device such as a computer
may not be played back in the order in which FOLDER LIST
they were recorded. 01 Let's Talk About Love (1985)
• The playback order for the system may differ 02 1st Album (1986)
03 In the Middle of Nowhere (1986)
from the playback order of the connected USB 04 Ready for Romance (1986)
05 In the Garden of Venus (1987)
device. 06 Romantic Warriors (1987)
07 Back for Good (1988)
• Always turn off the system before removing 08 Alone (1999)
the USB device. Removing the USB device
while the system is on may corrupt the data on
the USB device. 7 Press X/x to select a folder.
• Do not save other types of files or unnecessary
x To play audio files in a folder
folders on a USB device that has audio files or
Press H to start playing the selected
JPEG image files.
folder.
• Folders that have no audio files or JPEG image
files are skipped. x To select an audio file
• Compatibility with all MP3/WMA/AAC Press .
encoding/writing softwares, recording The list of files contained in the folder
devices, and recording media cannot be appears.
guaranteed. Incompatible USB device may
TRACK LIST
produce noise or interrupted audio or may not
03 In the Middle of Nowher...
play at all.
01_Geronimo_s_Cadillac
• Before using the USB device, make sure that 02_Riding_On_A_White_Swan
no virus-ridden files are on the USB device. 03_Give_Me_Peace_On_Earth
04_Sweet_Little_Shella
05_Ten_Thousand_Lonely_Drums
06_Lonely_Tears_In_Chinatown
07_In_Shaire
68GB
Press X/x to select a file and press . The folders recorded on the USB device
The system starts playing the selected file. appear. When a folder is being played, its
You can turn the file list off by pressing title is shaded.
DVD MENU. Pressing DVD MENU again
will display the folder list. FOLDER LIST
folder 9 10 11 12
69GB
To play the next or previous JPEG Note
image file • Some JPEG image files may take longer to display
than the option you selected. Especially progressive
Press c/C when the Control Menu display is not
JPEG image files or JPEG image files of 3,000,000
displayed. Note that you can select the next pixels or more.
folder by continuing to press c after the last
image on the current folder, but that you cannot To select an effect for JPEG
return to the previous folder by pressing C. To image files in the slide show
return to the previous folder, select the folder
from the folder list. 1 Press DISPLAY twice.
The Control Menu display appears on the
To rotate a JPEG image file TV screen.
When a JPEG image file is displayed on the TV
screen, you can rotate the JPEG image file by 90
2 Press X/x to select [EFFECT],
then press .
degrees.
The options for [EFFECT] appear.
Press X/x while viewing a JPEG image file.
Press CLEAR to return to normal view. 3 Press X/x to select a setting.
Note
• [MODE 1]: The JPEG image file sweeps
• You cannot rotate the JPEG image file when you set in from top to bottom.
[JPEG RESOLUTION] in [HDMI SETUP] to [(1920 • [MODE 2]: The JPEG image file stretches
× 1080i) HD ] or [(1920 × 1080i) HD]. out from left to right of the TV screen.
• [MODE 3]: The JPEG image file stretches
To stop playback
out from the center of the TV screen.
Press x. • [MODE 4]: The JPEG image files
randomly cycle through the effects.
Other operations
• [MODE 5]: The next JPEG image file
See “Other operations” (page 36).
slides over the previous image.
To select the slide show duration • [OFF]: Off.
of JPEG image files 4 Press .
1 Press DISPLAY twice. Note
The Control Menu display appears on the • The [EFFECT] setting is not effective when you set
TV screen. [JPEG RESOLUTION] in [HDMI SETUP] to [(1920
× 1080i) HD ] or [(1920 × 1080i) HD] (page 56).
2 Press X/x to select [INTERVAL],
then press .
The options for [INTERVAL] appear. Displaying the list of audio
3 Press X/x to select a setting. files/JPEG image files
• [NORMAL]: You can set the duration to
about 6 to 9 seconds. 1 Press DISPLAY during playback.
• [FAST]: You can set the duration shorter The Control Menu display appears on the
than [NORMAL]. TV screen.
• [SLOW 1]: You can set the duration 2 Press X/x to select
longer than [NORMAL]. [BROWSING], then press .
• [SLOW 2]: You can set the duration The options for [BROWSING] appear.
longer than [SLOW 1].
3 Press X/x to select the desired list,
4 Press . then press .
70GB
• [FOLDER LIST]: The list of folders
appears. Follow Step 2 of “Selecting an Searching for an audio file/
audio file or folder.”
JPEG image file/folder, etc.
• [PICTURE LIST]: Images of JPEG image
files in the folder appear in 16 subscreens. You can search a USB device by audio file,
Follow Step 2 of “Selecting a JPEG image JPEG image file, or folder. As audio files and
file or folder.” JPEG image files are assigned unique numbers
on the USB device, you can select the desired
audio file or JPEG image file by entering its
Playing repeatedly number.
(Repeat Play) 1 Press DISPLAY. (When playing a
JPEG image files, press DISPLAY
You can play the audio files/JPEG image files twice.)
71GB
4 Press X/x or the number buttons to
Bit rate
select the desired number.
If you make a mistake, press CLEAR to T 0: 13 192k MP3
cancel the number.
5 Press .
The system starts playback from the
selected number.
2002_Remixes
Viewing the information of an Soul_Survivor_rap_version
display * If an MP3 file has the ID3 tag, the system will
display a folder name/track (file) name from the ID3
Press DISPLAY repeatedly. tag information.
Each time you press DISPLAY while playing The system can support ID3 ver 1.0/1.1/2.2/2.3.
the disc, the display changes: ID3 ver 2.2/2.3 tag information display has priority
when both ID3 ver 1.0/1.1 and ver 2.2/2.3 tags are
1y2
used for a single MP3 file.
72GB
Tip
• Date information is [MM/DD/YYYY].
MM: Month
Storing Songs in a USB
DD: Day
YYYY: Year
Device
• Date information varies depending on the area. (DAV-DZ270 only)
You can record songs on an audio CD in a USB
device by encoding to MP3 format. You can also
copy the MP3 files on a DATA CD/DATA DVD
into the USB device.
For connecting the USB device, see
“Connecting the USB device” (page 67).
73GB
same name, a sequential number is added after x To cancel the track
the name without overwriting the original Press X/x to select the track, then press .
folder or file. The mark on the track is removed.
• Some USB devices cannot be played back on x To cancel all the track
the system depending on the file format. Press C/X/x/c to select [s ALL], then
press .
74GB
Recordable space of
2 Press X/x to select a folder.
the USB device x To erase all audio files in a folder
Press CLEAR.
USB RECORDING Free:
2002_Remixes x To erase an audio file
01_Back_Seat_O... START Press .
02_One_Nights_...
ALL The list of files contained in the folder
03_Are_You_Ma...
04_I_Can_Lose_... ALL
05_Soul_Survivo...
appears.
06_Strangers_B... Press X/x to select the desired audio file,
07_Stay_maxi_ve...
then press CLEAR.
75GB
Playable USB Devices Using the DIGITAL MEDIA
(DAV-DZ270 only) PORT Adapter
You can use the following Sony USB devices on
the system. (DAV-HDZ278 only)
The DIGITAL MEDIA PORT (DMPORT)
Verified Sony digital music player adapter (not supplied) is for enjoying sound
(as of April 2007) from a portable audio source or computer. By
connecting a DIGITAL MEDIA PORT adapter,
Product name Model name you can enjoy sound from the connected
Walkman® NWD-B103/B105/B103F/B105F component on the system.
NWZ-A815/A816/A818 Available DIGITAL MEDIA PORT adapters
NWZ-S515/S516/S615F/S616F/ vary in each area.
S618F For details on connecting the DIGITAL MEDIA
PORT adapter, see “To connect the DIGITAL
Verified Sony IC recorder (as of MEDIA PORT adapter” (page 22).
April 2007) Note
• Do not connect an adapter other than the DIGITAL
Product name Model name MEDIA PORT adapter.
IC Recorder ICD-U50/U60/U70 • Do not connect or disconnect the DIGITAL MEDIA
ICD-SX57/SX67/SX77 PORT adapter to/from the unit while the system is
turned on.
Verified Sony USB storage media • Depending on the type of DIGITAL MEDIA PORT
adapter, the images are also output. In this case, the
(as of April 2007)
system outputs the composite video signal only,
regardless of the type of video signal.
Product name Model name
MICROVAULT USM 512JX/1GJX/2GJX/4GJX
76GB
• Depending on the type of DIGITAL MEDIA PORT
adapter, you may be able to operate a connected
component using either the buttons on the remote or
the unit. The following illustration shows an example
of buttons that can be used in this case.
H
x
X
77GB
• [NO CENTER]: Select this when you
install the front and surround speakers
Other Operations only.
• [NO SURROUND]: Select this when you
Getting Optimal install the center and front speakers only.
• [FRONT ONLY]: Select this when you
Surround Sound for a install the front speakers only.
“DVD” appears in the front panel The setting is made and the confirmation
display. display appears.
2 Press DISPLAY while the system is 9 Press C/c to select [YES] or [NO], then
in stop mode. press .
The Control Menu display appears on the • [YES]: Continue with [AUTO
TV screen. CALIBRATION]. Follow the procedure
from Step 7 of “Calibrating the
3 Press X/x to select [SETUP], Appropriate Settings Automatically”
then press . (page 79).
The options for [SETUP] appear. • [NO]: Exit [SPEAKER FORMATION].
4 Press X/x to select [CUSTOM], then Note
press . • In order to enjoy the surround sound after you change
The Setup Display appears. the position of the speakers, Sony recommends you
set [SPEAKER FORMATION], and then set [AUTO
5 Press X/x to select [AUDIO SETUP], CALIBRATION] (page 79).
then press . • When you change the [CONNECTION] setting in
The options for [AUDIO SETUP] appear. [SPEAKER SETUP] (page 58), the [SPEAKER
6 Press X/x to select [SPEAKER
FORMATION] setting returns to [STANDARD].
FORMATION], then press .
The options for [SPEAKER
FORMATION] appear.
SPEAKER FORMATION
STANDARD
78GB
obstruction between the speakers and the
Calibrating the calibration mic.
Appropriate Settings
Automatically
IC
AL M
[AUTO CALIBRATION] A.C
I O IN /
D. C. A. C. (Digital Cinema Auto Calibration) AUD
can set the appropriate surround sound
automatically.
Note
• The system outputs a loud test sound when [AUTO
CALIBRATION] starts. You cannot turn the volume
Calibration mic
down. Give consideration to children and neighbors.
• Make sure that the headphones are not connected to
Other Operations
the unit. You cannot operate the following Steps with
the headphones connected.
The options for [AUDIO SETUP] appear. • Avoid being in the measurement area and
making noise during the measurement (about 3
6 Press X/x to select [AUTO minute), to avoid measurement failure. During
CALIBRATION], then press . the measurement, test signals are output from
The options for [AUTO CALIBRATION] the speakers.
appear. • The environment of the room in which the
system is installed may affect measurements.
7 Connect the calibration mic (supplied) • If an error message appears, follow the message,
to the A.CAL MIC jack on the front then select [YES].
panel An error message appears when:
Set up the calibration mic at the ear level – the headphones are connected to the unit.
using a tripod, etc. (not supplied). – the calibration mic is not connected.
The front of each speaker should face the – front speakers are not correctly connected.
calibration mic, and there should be no – surround speakers are not correctly
connected.
79GB
– front and surround speakers are not correctly
connected.
Controlling the TV with
10 Press C/c to select [YES] or [NO], then
press . the Supplied Remote
x The measurement is OK.
You can control the TV (Sony only) by using
Disconnect the calibration mic, then select
following buttons. Use these buttons (other than
[YES]. The result is implemented.
TV [/1, TV INPUT, and TV VOL +/–) while
x The measurement is not OK. pressing the TV button.
Follow the message, then select [YES] to
Note
retry. • Depending on the TV, you may not be able to control
Note your TV or to use some of the buttons.
• While the Auto Calibration function works: • Depending on the area, the name of the button may
– do not turn off the power. differ.
– do not press any button.
By pressing You can
– do not change the volume.
– do not change the function. TV [/1 Turn the TV on/off.
– do not change the disc. TV INPUT Switch the TV’s input source
– do not insert or eject a disc. between the TV and other input
sources.
– do not connect the headphones to the unit.
– do not disconnect the calibration mic. TV VOL +/– Adjust the TV volume.
• The measurement for [SUBWOOFER] is always TV CH +/–* Select the TV channel.
[YES] since the system does not perform subwoofer (PROG +/–*)
calibration. Number Select the TV channel.
buttons*, -*
Tip
ENTER*
• You can check the distance between the listening
position and each speaker. See page 58. TOOLS* Displays the operation menu for
the current display.
RETURN* Return to the previous channel or
layer on the menu of the TV.
MENU* Display the menu of the TV.
MUTING* Turn off the TV sound
temporarily.
C/X/x/c*, * Select the item on the menu.
80GB
Using the Sound Effect Using the Sleep Timer
You can set the system to turn off at a preset
Reinforcing bass frequencies time, so you can fall asleep listening to music.
You can preset the time in 1 or 10-minutes
You can reinforce bass frequencies. increments.
Press DYNAMIC BASS. Press SLEEP.
“D. BASS ON” appears in the front panel Each time you press SLEEP, the minutes display
display and bass frequencies are effectively (the remaining time) changes by 10-minutes.
reinforced. When you set the sleep timer, “SLEEP” flashes
in the front panel display.
To turn off the sound effect
Press DYNAMIC BASS again. To check the remaining time
Press SLEEP once.
Other Operations
Enjoying the sound at low To change the remaining time
Press SLEEP repeatedly to select the desired
volume
time.
You can enjoy sound effects or dialogue, as you To cancel the sleep timer
would in a movie theater, even at low volume. It function
is useful for watching movies at night.
Press SLEEP repeatedly until “SLEEP OFF”
Press NIGHT. appears in the front panel display.
“NIGHT ON” appears in the front panel display
and the sound effect is activated. To set the sleep timer using the
system menu
Note
• This effect does not work for a Super Audio CD. 1 Press SYSTEM MENU.
When you load a Super Audio CD during “NIGHT
ON,” the sound effect turns off automatically.
2 Press X/x repeatedly until “SLEEP”
appears in the front panel display, then
• When sound is output from the center speaker, this
press or c.
effect is more pronounced, as speech (movie dialog,
etc.) is easy to hear. When sound is not output from 3 Press X/x to select a setting.
the center speaker, or you are using the headphones,
The minutes display (the remaining time)
the system optimally adjusts the volume.
changes in 10-minutes.
To turn off the sound effect
Tip
Press NIGHT again. • You can select the remaining time by pressing
the number buttons. In this case, you can preset
the time in 1-minute increments.
4 Press .
The setting is made and “SLEEP” flashes in
the front panel display.
5 Press SYSTEM MENU.
The system menu turns off.
81GB
Changing the Brightness Viewing Information
of the Front Panel About the Disc
Display
The brightness of the front panel display can be
set to either of 2 levels.
1 Press SYSTEM MENU.
Viewing the playing time and
2 Press X/x repeatedly until “DIMMER”
remaining time in the front
appears in the front panel display, then panel display
press or c.
Press DISPLAY repeatedly.
3 Press X/x to select the brightness of
the front panel display. Each time you press DISPLAY while playing
the disc, the display changes:
• “DIMMER OFF”: Bright.
1 t 2 t ... t 1 t ...
• “DIMMER ON”: Dark.
Some displayed items may disappear after a few
4 Press . seconds.
The setting is made. x DVD VIDEO/DVD-VR
5 Press SYSTEM MENU. 1 Playing time of the current title
The system menu turns off. 2 Remaining time of the current title
3 Playing time of the current chapter
4 Remaining time of the current chapter
5 Disc name
6 Title and chapter
x VIDEO CD (without PBC functions)/
Super Audio CD/CD
1 Playing time of the current track
2 Remaining time of the current track
3 Playing time of the disc
4 Remaining time of the disc
5 Track name
6 Track and index*
* VIDEO CD/Super Audio CD only.
x DATA CD (MP3 file)/DATA DVD (MP3 file)
1 Playing time and current track number
2 Track (file) name*
* If an MP3 file has the ID3 tag, the system will
display a folder name/track (file) name from the ID3
tag information.
The system can support ID3 ver 1.0/1.1/2.2/2.3.
ID3 ver 2.2/2.3 tag information display has priority
when both ID3 ver 1.0/1.1 and ver 2.2/2.3 tags are
used for a single MP3 file.
x DATA CD (DivX video file)/DATA DVD
(DivX video file) (Except for United
Kingdom and North American models)
1 Playing time of the current file
82GB
2 Current file name x VIDEO CD (without PBC functions)/
3 Current album and file number Super Audio CD/CD
• T **:**
Note
Playing time of the current track
• The system can only display the first level of the
DVD/CD text, such as the disc name or title. • T-**:**
• If a file name of the MP3 file cannot be displayed, “*” Remaining time of the current track
will appear in the front panel display instead. • D **:**
• The disc name or track name may not be displayed Playing time of the current disc
depending on the text. • D-**:**
• Playing time of MP3 files and DivX video files* may Remaining time of the current disc
not be displayed correctly.
* Except for United Kingdom and North American x DATA CD (MP3 file)/DATA DVD (MP3
models. file)
• T **:**
Tip Playing time of the current track
• When the system is playing a VIDEO CD with PBC
functions, the playing time is displayed. x DATA CD (DivX video file)/DATA
DVD (DivX video file) (Except for United
Other Operations
Kingdom and North American models)
Viewing the playing time and • **:**:**
Playing time of the current file
remaining time on the TV
Note
screen • Characters/marks may not be displayed in some
languages.
1 Press DISPLAY during playback. • Depending on the type of disc being played, the
The following display appears on the TV system can only display a limited number of
screen. characters. Also, depending on the disc, not all text
characters will be displayed.
T 1: 01: 40
Time information
Checking the play information
of the disc
2 Press DISPLAY repeatedly to change
the time information. To check DVD/Super Audio CD/CD
The display and the kinds of time that you text
can check depend on the disc you are
Press DISPLAY repeatedly during playback to
playing.
display text recorded in the DVD/Super Audio
x DVD VIDEO/DVD-VR CD/CD.
• T **:**:** The DVD/Super Audio CD/CD text appears
Playing time of the current title only when text is recorded in the disc. You
• T-**:**:** cannot change the text. If the disc does not
Remaining time of the current title contain text, “NO TEXT” appears.
• C **:**:**
Playing time of the current chapter
• C-**:**:**
Remaining time of the current chapter Dvorak/Tchaikovsky /NedPho/Kreizberg
Adagio - Allegro molto
x VIDEO CD (with PBC functions)
• **:**
Playing time of the current scene
83GB
To check DATA CD/DATA DVD
5( 8)
(MP3 file/DivX video file3)) text 10( 15) DATA CD JPEG
9/18/2002
By pressing DISPLAY while playing MP3 files
or DivX video files3) on a DATA CD/DATA
DVD, you can display the name of the folder/ Date information
MP3 file/DivX video file3), and the audio bit
rate (the amount of data per second of the
current audio) on the TV screen.
* “Exchangeable Image File Format” is a digital
Bit rate1) camera image format defined by the Japan
Electronics and Information Technology Industries
T 0: 13 192k MP3 Association (JEITA).
Tip
• Date information is [MM/DD/YYYY].
MM: Month
DD: Day
YYYY: Year
• Date information varies depending on the area.
2002_Remixes
Soul_Survivor_rap_version
1)Appears when:
– playing an MP3 file on a DATA CD/DATA DVD.
– playing a DivX video file that contains MP3 audio
signals on a DATA CD/DATA DVD (except for
United Kingdom and North American models).
2)
If an MP3 file has the ID3 tag, the system will display
a folder name/track (file) name from the ID3 tag
information.
The system can support ID3 ver 1.0/1.1/2.2/2.3.
ID3 ver 2.2/2.3 tag information display has priority
when both ID3 ver 1.0/1.1 and ver 2.2/2.3 tags are
used for a single MP3 file.
3)
Except for United Kingdom and North American
models.
84GB
5 Press X/x to select [SYSTEM SETUP],
Returning to the Default then press .
The options for [SYSTEM SETUP] appear.
Settings 6 Press X/x to [RESET] and press c.
7 Press C/c to select [YES].
Returning the system You can also quit the process and return to
parameters, such as preset the Control Menu display by selecting [NO]
here.
stations, to the default
8 Press .
settings Do not press [/1 while resetting the system
as it takes a few seconds to complete.
"/1 A x Note
• The [MODE (MUSIC, IMAGE)], [INTERVAL],
[EFFECT], and [MULTI/2CH] settings are also
return to the default settings.
Other Operations
1 Press "/1 to turn on the system.
2 Press x, A, and "/1 on the unit at the
same time.
“COLD RESET” appears in the front panel
display and the system returns to default
settings.
85GB
On adjusting volume
• Do not turn up the volume while listening to a section
Additional Information with very low level inputs or no audio signals. If you
do, the speakers may be damaged when a peak level
Precautions section is suddenly played.
On cleaning
On power sources
• Clean the cabinet, panel, and controls with a soft cloth
• Unplug the unit from the wall outlet (mains) if you do slightly moistened with a mild detergent solution. Do
not intend to use it for an extended period of time. To not use any type of abrasive pad, scouring powder or
disconnect the cord, pull it out by the plug, never by solvent such as alcohol or benzine.
the cord. If you have any questions or problems concerning
On placement your system, please consult your nearest Sony dealer.
86GB
Notes about the Discs
On handling discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
• Do not stick paper or tape on the disc.
Additional Information
On cleaning
• Before playing, clean the disc with a cleaning
cloth.
Wipe the disc from the center out.
87GB
Troubleshooting
If you experience any of the following difficulties while using the system, use this troubleshooting
guide to help remedy the problem before requesting repairs. Should any problem persist, consult your
nearest Sony dealer.
Note that if service personnel changes some parts during repair, these parts may be retained.
Power
Symptom Remedy
The power is not turned on. • Check that the AC power cord (mains lead) is connected securely.
• Press "/1 after “STANDBY” disappears from the front panel display.
If “PROTECTOR” and “PUSH Press "/1 to turn off the system, and check the following items after
POWER” appear alternately in “STANDBY” disappears.
the front panel display. • Are the + and – speaker cords short-circuited?
• Are you using only the specified speakers?
• Is anything blocking the ventilation holes of the system?
• After checking the above items and fixing any problems, turn on the system. If
the cause of the problem cannot be found even after checking all the above
items, consult your nearest Sony dealer.
Picture
Symptom Remedy
There is no picture. • The video connecting cords are not connected securely.
• The video connecting cords are damaged.
• The unit is not connected to the correct TV input jack (page 18).
• The video input on the TV is not set so that you can view pictures from the
system.
• Check the output method on your system (page 18).
• You have set progressive format but your TV cannot accept the signal in
progressive format. In this case, return the setting to interlace format (the
default setting) (page 29).
• Even if your TV is compatible with progressive format (525p/625p) signals, the
image may be affected when you set progressive format. In this case, return the
setting to interlace format (the default setting) (page 29).
• Re-connect the connecting cord securely.
• The unit is connected to an input device that is not HDCP (High-bandwidth
Digital Content Protection) compliant (“HDMI” on the front panel does not
light up) (page 18).
• If the HDMI OUT jack is used for video output, changing the type of video
signal output from the HDMI OUT jack. It may solve the problem (page 29).
Connect the TV and the unit using a video jack other than the HDMI OUT, and
switch the TV’s input to the connected video input so that you can see the on-
screen displays. Change the type of video signal output from the HDMI OUT
jack, and switch the TV’s input back to HDMI. If the picture still does not
appear, repeat the Steps and try other options.
• You have set [PROGRESSIVE (COMPONENT OUT)] in [VIDEO SETUP] to
[ON] (page 54) even though your TV cannot accept the progressive signal. In
this case, disconnect the HDMI cable from the unit and then set to [OFF].
88GB
Symptom Remedy
Picture noise appears. • The disc is dirty or flawed.
• If the picture output from your system goes through your VCR to get to your
TV, the copy-protection signal applied to some DVD programs could affect
picture quality. If you still experience problems even when you connect your
unit directly to your TV, try connecting your unit to your TV’s video input
(page 18).
* Depending on the country model, [720 × 576p] may appear.
Even though you set the aspect • The aspect ratio on the disc is fixed.
ratio in [TV TYPE] of [VIDEO
SETUP], the picture does not fill
the TV screen.
Color irregularity occurs on the The subwoofer and the front speakers in this system are magnetically shielded to
TV screen. prevent magnetic leakage. However, some leakage may occur, as a high-strength
magnet is employed. If this happens, check the following items:
• If the speakers are used with a CRT-based TV or projector, install the speakers
at least 0.3 meters (1.0 ft) from the TV set.
• If the color irregularity persists, turn off the TV set once, then turn it on after 15
to 30 minutes.
• If howling occurs, reposition the speakers farther away from the TV set.
Additional Information
• Make sure that no magnetic object (magnetic latch on a TV stand, health care
device, toy, etc.) is placed near the speakers.
Sound
Symptom Remedy
There is no sound. • The speaker cord is not connected securely.
• Press MUTING on the remote if “MUTING ON” is displayed in the front panel
display.
• The system is in pause mode or in Slow-motion Play mode. Press H to return
to normal play mode.
• Fast forward or fast reverse is performed. Press H to return to normal play
mode.
• Check the speaker settings (page 58).
• Super Audio CD audio signals are not output from the HDMI OUT jack.
• The component connected to the HDMI OUT jack does not conform to the
audio signal format, in this case set [AUDIO (HDMI)] in [HDMI SETUP] to
[ON] (page 56).
No sound is output from the • Set [AUDIO (HDMI)] in [HDMI SETUP] to [ON] (page 56).
HDMI OUT jack. • The HDMI OUT jack is connected to a DVI (Digital Visual Interface) device
(DVI (Digital Visual Interface) jacks do not accept audio signals).
• The HDMI OUT jack does not output Super Audio CD sound.
• Try the following: 1 Turn the system off and on again. 2 Turn the connected
component off and on again. 3 Disconnect and then connect the HDMI cable
again.
The left and right sounds are • Check that the speakers and components are connected correctly and securely.
unbalanced or reversed.
There is no sound from the • Check the speaker connections and settings (pages 16, 58).
subwoofer. • Select “A.F.D. STD” for “DEC. MODE” (page 32).
89GB
Symptom Remedy
Severe hum or noise is heard. • Check that the speakers and components are connected securely.
• Check that the connecting cords are away from a transformer or motor, and at
least 3 meters (10 ft) away from your TV set or a fluorescent light.
• Move your TV away from the audio components.
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with
alcohol.
• Clean the disc.
The sound loses stereo effect • Set [AUDIO] to [STEREO] by pressing AUDIO (page 37).
when you play a VIDEO CD, a • Make sure the unit is connected properly.
CD, or an MP3 file.
The surround effect is difficult to • Make sure the “DEC. MODE” setting (page 32).
hear when you are playing a • Check the speaker connections and settings (pages 16, 58).
sound track of Dolby Digital, • Depending on the DVD, the output signal may not be the entire 5.1 channel. It
DTS, or MPEG audio. may be monaural or stereo even if the sound track is recorded in Dolby Digital
or MPEG audio format.
The sound comes from the center • Depending on the disc, the sound may come from the center speaker only.
speaker only.
No sound is heard from the • Check the speaker connections and settings (pages 16, 58).
center speaker. • Make sure the “DEC. MODE” setting (page 32).
• Depending on the source, the effect of the center speaker may be less
noticeable.
• A 2 channel source is being played.
No sound or only a very low- • Check the speaker connections and settings (pages 16, 58).
level sound is heard from the • Make sure the “DEC. MODE” setting (page 32).
surround speakers. • Depending on the source, the effect of the surround speakers may be less
noticeable.
• A 2 channel source is being played.
There is no sound from the • The sampling frequency of the input signal is more than 48 kHz.
DIGITAL IN COAXIAL/
OPTICAL jack (DAV-HDZ278
only).
Operation
Symptom Remedy
Radio stations cannot be tuned • Check that the antenna (aerial) is connected securely. Adjust the antenna
in. (aerial) or connect an external antenna (aerial) if necessary.
• The signal strength of the stations is too weak (when tuning in with automatic
tuning). Use direct tuning.
• No stations have been preset or the preset stations have been cleared (when
tuning by scanning preset stations). Preset the stations (page 61).
• Press DISPLAY so that the frequency appears in the front panel display.
The remote does not function. • There are obstacles between the remote and the unit.
• The distance between the remote and the unit is too far.
• The remote is not pointed at the remote sensor on the unit.
• The batteries in the remote are weak.
90GB
Symptom Remedy
The disc does not play. • There is no disc inserted.
• The disc is upside down.
Insert the disc with the playback side facing down.
• The disc is skewed on the disc tray.
• The system cannot play CD-ROMs, etc. (page 6).
• The region code on the DVD does not match the system.
• Moisture has condensed inside the unit and may cause damage to the lenses.
Remove the disc and leave the unit turned on for about half an hour.
The MP3 file cannot be played. • The DATA CD is not recorded in the MP3 format that conforms to ISO 9660
Level 1/Level 2, or Joliet.
• The DATA DVD is not recorded in an MP3 format that conforms to UDF
(Universal Disk Format).
• The MP3 file does not have the extension “.MP3.”
• The data is not formatted in MP3 even though it has the extension “.MP3.”
• The data is not MPEG1 Audio Layer 3 data.
• The system cannot play audio tracks in MP3PRO format.
• The [MODE (MUSIC, IMAGE)] setting has been set to [IMAGE] (page 46).
• If you cannot change the [MODE (MUSIC, IMAGE)] setting, re-load the disc
Additional Information
or turn the system off, then on.
• The DATA CD/DATA DVD contains a DivX video file (except for United
Kingdom and North American models).
The JPEG image file cannot be • The DATA CD is not recorded in a JPEG format that conforms to ISO 9660
played. Level 1/Level 2, or Joliet.
• The DATA DVD is not recorded in a JPEG format that conforms to UDF
(Universal Disk Format).
• It has an extension other than “.JPEG” or “.JPG.”
• It is larger than 3,072 (width) × 2,048 (height) in normal mode, or more than
2,000,000 pixels in Progressive JPEG image file which is mainly used on the
Internet WEB site.
• It does not fit the TV screen (those images are reduced).
• The [MODE (MUSIC, IMAGE)] setting has been set to [MUSIC] (page 46).
• If you cannot change the [MODE (MUSIC, IMAGE)] setting, re-load the disc
or turn the system off, then on.
• The DATA CD/DATA DVD contains a DivX video file (except for United
Kingdom and North American models).
The MP3 files and JPEG image • [AUTO] has been selected in [MODE (MUSIC, IMAGE)] (page 46).
files starts playing
simultaneously.
The DivX video file cannot be • The file is not created in DivX format.
played (except for United • The file has an extension other than “.AVI” or “.DIVX.”
Kingdom and North American • The DATA CD/DATA DVD is not created in a DivX format that conforms to
models). ISO 9660 Level 1/Level 2 or, Joliet/UDF.
• The DivX video file is larger than 720 (width) × 576 (height).
The titles of folder/file/file name • The system can only display numbers and letters of the alphabets. Other
are not displayed correctly. characters are displayed as [*].
91GB
Symptom Remedy
A disc does not start playing • Program Play, Shuffle Play, or Repeat Play has been selected.
from the beginning. Press CLEAR to cancel these functions before playing a disc.
• Resume Play has been selected.
During stop, press x on the unit or the remote and then start playback
(page 39).
• The title, DVD or PBC menu automatically appears on the TV screen.
The system starts playing the • The DVD features an auto playback function.
disc automatically.
Playback stops automatically. • Some discs may contain an auto pause signal. While playing such a disc, the
system stops playback at the auto pause signal.
You cannot perform some • Depending on the disc, you may not be able to perform some of the operations
functions such as stop, search, above. Refer to the operating instructions supplied with the disc.
Slow-motion Play, or Repeat
Play.
Messages do not appear on the • In the Setup Display, select the desired language for the on-screen display in
TV screen in the language you [OSD] under [LANGUAGE SETUP] (page 53).
want.
The language for the sound track • Multilingual tracks are not recorded on the DVD being played.
cannot be changed. • The DVD prohibits changing the language for the sound track.
The subtitle language cannot be • Multilingual subtitles are not recorded on the DVD being played.
changed. • The DVD prohibits changing the subtitles.
The subtitle cannot be turned off. • The DVD prohibits turning off subtitles.
The angles cannot be changed. • Multi-angles are not recorded on the DVD being played (page 36).
• The DVD prohibits changing the angles.
A disc cannot be ejected and • Contact your Sony dealer or local authorized Sony service facility.
“LOCKED” appears in the front
panel display.
[Data error] appears on the TV • The MP3 file/JPEG image file/DivX video file you want to play is broken
screen when playing a DATA (except for United Kingdom and North American models).
CD or DATA DVD. • The data is not MPEG1 Audio Layer 3 data.
• The JPEG image file format does not conform to DCF.
• The JPEG image file has the extension “.JPG” or “.JPEG,” but is not in JPEG
format.
• The file you want to play has the extension “.AVI” or “.DIVX” but is not in
DivX format, or is in DivX format but does not conform to a DivX Certified
profiles (except for United Kingdom and North American models).
The system does not work • Disconnect the AC power cord (mains lead) from the wall outlet (mains), then
normally. reconnect after several minutes.
92GB
Symptom Remedy
The Control for HDMI function • When “HDMI” does not light up in the front panel display, check the HDMI
does not work. connection (page 18).
• Set the [CONTROL FOR HDMI] setting in [HDMI SETUP] to [ON] (page 55).
• Make sure that the connected component is compatible with the [CONTROL
FOR HDMI] function.
• Check that the AC power cord (mains lead) of the connected component is
connected securely.
• Check the connected component’s setting for the Control for HDMI function.
Refer to the operating instructions supplied with the component.
• If you change the HDMI connection, connect and disconnect the AC power
cord (mains lead), or have a power failure, set the [CONTROL FOR HDMI]
setting in [HDMI SETUP] to [OFF], then set the [CONTROL FOR HDMI]
setting in [HDMI SETUP] to [ON] (page 55).
• For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
(page 64).
No sound is output from the • Set the [AUDIO (HDMI)] setting in [CUSTOM SETUP] to [ON] (page 56).
system and TV while using the • Make sure that the connected TV is compatible with the System Audio Control
System Audio Control function. function.
• For details, see “Using the Control for HDMI Function for “BRAVIA” Sync”
Additional Information
(page 64).
USB device
(DAV-DZ270 only)
Symptom Remedy
“OVERLOAD” appears in the • A problem has been detected with the level of electrical current from the
front panel display. (USB) port. Turn off the system and remove the USB device from the
(USB) port. Make sure there is no problem with the USB device. If this display
pattern persists, contact your nearest Sony dealer.
Are you using a supported USB • If you connect an unsupported USB device, the following problems may occur.
device? See “Playable USB Devices” (page 76) for the supported device types.
– The USB device is not recognized.
– File or folder names are not displayed on this system.
– Playback is not possible.
– The sound skips.
– There is noise.
– A distorted sound is output.
– Recording stops before it is finished.
There is no sound. • The USB device is not connected correctly. Turn off the system, then reconnect
the USB device.
The sound is distorted. • The bit rate used when encoding the audio files was low. Send audio files
encoded with higher bit rates to the USB device.
There is noise or the sound skips. • Turn off the system, then reconnect the USB device.
• Noise may have entered during the recording or copying process. Delete the
file, and try recording or copying again.
• Copy the files to your computer, format the USB device in FAT12, FAT16, or
FAT32 format, and copy the files to the USB device again.*
* This system supports FAT12, FAT16, and FAT32, but some USB device may
not support all of these FAT. For details, refer to the operating instructions of
each USB device or contact the manufacturer.
93GB
Symptom Remedy
The USB device cannot be The USB device is being connected backwards. Connect the USB device in the
connected into the (USB) correct orientation.
port.
The USB device which has been • It may be recorded in an unsupported format. If so, first take the precaution of
used on another device does not backing up important files on the USB device by copying them to your
work. computer hard disk. Next, format the USB device with a FAT12, FAT16, or
FAT32 file system and transfer the backed-up audio files onto the USB device
again.*
* This system supports FAT12, FAT16, and FAT32, but some USB device may
not support all of these FAT. For details, refer to the operating instructions of
each USB device or contact the manufacturer.
“READING” is displayed for a • The reading process can take a long time in the following cases.
long time. – There are many folders or files on the USB device.
– The file structure is extremely complex.
– The memory capacity is excessive.
– The internal memory is fragmented.
• Sony recommends following these guidelines.
– Total folders on the USB device: 200 or less
– Total files per folder: 150 or less
Erroneous display. • Send the music data to the USB device again, as the data stored in the USB
device may have been corrupted.
• The character codes that can be displayed by this system are numbers and
alphabet only. Other characters are not displayed correctly.
“DATA ERROR” appears in the • The audio file/JPEG image file you want to play is broken.
front panel display during • The data is not MPEG1 Audio Layer 3 data.
playback of an USB device. • The JPEG image file format does not conform to DCF.
• The JPEG image file has the extension “.JPG” or “.JPEG,” but is not in JPEG
format.
Playback does not start. • Turn off the system, then reconnect the USB device.
• Connect the USB device that this system can play (page 76).
• Press H to start play.
Playback does not start from the • Cancel Repeat Play (page 71).
first track.
94GB
Symptom Remedy
The USB device (audio file/ • USB device formatted with file systems other than FAT12, FAT16, or FAT32
JPEG image file) cannot be are unsupported.*
played back. • Files that are encrypted or protected by passwords, etc. cannot be played back.
• The MP3 file does not have the extension “.MP3.”
• The WMA file does not have the extension “.wma.”
• The AAC file does not have the extension “.m4a.”
• The data is not stored in the desired format.
• The MP3 files in format other than MPEG 1 Audio Layer 3 cannot be played
back.
• If you use partitioned USB device, only audio files on the first partition can be
played.
• The system can playback to a depth of 8 folders only.
• For audio files/JPEG image files, check the [MODE (MUSIC, IMAGE)] setting
(pages 68, 69).
• The number of folders has exceeded 200.
• The number of files has exceeded 150.
• For audio files/JPEG image files, the folder contains more than 150 files.
• The JPEG image file does not have the extension “.JPG” or “.JPEG.”
Additional Information
• The JPEG image file is larger than 3,072 (width) × 2,048 (height) in normal
mode, or more than 2,000,000 pixels in Progressive JPEG mode which is
mainly used on the Internet website.
• JPEG image files with a high width to length ratio cannot be played back.
• A WMA file that is the WMA DRM, WMA Lossless, or WMA PRO format
cannot be played back.
• An AAC file that is the AAC DRM or AAC Lossless format cannot be played
back.
* This system supports FAT12, FAT16, and FAT32, but some USB device may
not support all of these FAT. For details, refer to the operating instructions of
each USB device or contact the manufacturer.
Audio files or JPEG image files • After the system reads all files on the USB device, playback may take more
take longer to play back than time than usual if:
others. – the number of folders or files is very large.
– the folder or file organization structure is very complex.
– the memory capacity is very large.
– the file size is extremely large.
– the physical structure within the memory is fragmented.
• Sony recommends following these guidelines.
– Total folders on the USB device: 200 or less
– Total files per folder: 150 or less
You cannot start recording/ • The following problems may have occurred.
copying to an USB device. – The USB device is full.
– The number of MP3 files and folders on the USB device has reached the
upper limit.
– The USB device is write-protected.
Recording/copying is stopped • The communication speed of the USB device is extremely slow. Connect the
before it is finished. USB device that this system can play.
• If the recording, copying, and erase operations are repeated multiple times, the
file structure within the USB device becomes complex. Follow the procedure
in the operating instructions of the USB device to format the USB device. If the
problem persists, contact your nearest Sony dealer.
95GB
Symptom Remedy
Recording to an USB device • You are using an unsupported USB device. See “Playable USB Devices”
results in an error. (page 76).
• The USB device was disconnected or the power was turned off during
recording/copying. Delete the partially-recorded file, and record/copy again. If
this does not fix the problem, the USB device may be broken. Follow the
procedure in the operating instructions of the USB device to format the USB
device. If the problem persists, contact your nearest Sony dealer.
Audio files or folders on the • Check if the USB device is write-protected.
USB device cannot be erased. • The USB device was disconnected or the power was turned off during erasing.
Delete the partially-erased file. If this does not fix the problem, the USB device
may be broken. Follow the procedure in the operating instructions of the USB
device to format the USB device. If the problem persists, contact your nearest
Sony dealer.
96GB
When displaying the version
Self-diagnosis Function number on the TV screen
When you turn on the system, the version
(When letters/numbers appear in the number [VER.X.XX] (X is a number) may
display) appear on the TV screen. Although this is not a
malfunction and for Sony service use only,
When the self-diagnosis function is activated to normal system operation will not be possible.
prevent the system from malfunctioning, a 5- Turn off the system, and then turn on the system
character service number (e.g., C 13 50) with a again to operate.
combination of a letter and 4 digits appears on
the TV screen or front panel display. In this case,
VER.X.XX
check the following table.
C:13:50
Additional Information
characters of
the service
number
C 13 The disc is dirty.
,Clean the disc with a soft cloth
(page 87).
C 31 The disc is not inserted correctly.
,Restart the system, then re-insert
the disc correctly.
E XX To prevent a malfunction, the
(XX is a system has performed the self-
number) diagnosis function.
,Contact your nearest Sony
dealer or local authorized Sony
service facility and give the 5-
character service number.
Example: E 61 10
97GB
Super Audio CD/DVD System
Specifications Laser Semiconductor laser
(Super Audio CD/DVD: λ
= 650 nm)
AUDIO POWER SPECIFICATIONS
(CD: λ = 790 nm)
for the US model Emission duration:
POWER OUTPUT AND TOTAL HARMONIC continuous
DISTORTION: Signal format system
With 3 ohms loads, both North American, Mexican, and Latin American
channels driven, from 180 models:
- 20,000 Hz; rated 84 watts NTSC
per channel minimum Other models: NTSC/PAL
RMS power, with no more
than 0.7% total harmonic USB Section (DAV-DZ270 only)
distortion from 250 milli Supported bit rate
watts to rated output. MP3 (MPEG 1 Audio Layer-3):
32 kbps - 320 kbps
Amplifier Section
WMA: 48 kbps - 192 kbps
US models:
AAC: 48 kbps - 320 kbps
Surround mode (reference) RMS output power
Sampling frequencies
FL/FR/C/SL/SR*: 142 watts
MP3 (MPEG 1 Audio Layer-3):
(per channel at 3 ohms, 1
32/44.1/48 kHz
kHz, 10% THD)
WMA: 44.1 kHz
Subwoofer*: 140 watts (at
AAC: 44.1 kHz
3 ohms, 80 Hz, 10% THD)
(USB) port:
Chinese models:
Maximum current: 500 mA
Surround mode (reference) RMS output power
FL/FR/C/SL/SR*: 100 Tuner Section
watts (per channel at 3 System PLL quartz-locked digital
ohms, 1 kHz) synthesizer
Subwoofer*: 100 watts (at FM tuner section
3 ohms, 80 Hz) Tuning range
Other models: North American models: 87.5 MHz - 108.0 MHz
Stereo mode (rated) 108 W + 108 W (at 3 ohms, (100 kHz step)
1 kHz, 1% THD) Other models: 87.5 MHz - 108.0 MHz (50
Surround mode (reference) RMS output power kHz step)
FL/FR/C/SL/SR*: 142 Antenna (aerial) FM wire antenna (aerial)
watts (per channel at 3 Antenna (aerial) terminals 75 ohms, unbalanced
ohms, 1 kHz, 10% THD) Intermediate frequency 10.7 MHz
Subwoofer*: 140 watts (at AM tuner section
3 ohms, 80 Hz, 10% THD) Tuning range
* Depending on the decoding mode settings and the North American, Mexican, and Latin American
source, there may be no sound output. models:
530 kHz - 1,710 kHz (with
Inputs (Analog) the interval set at 10 kHz)
TV/VIDEO (AUDIO IN) Sensitivity: 450/250 mV 531 kHz - 1,710 kHz (with
AUDIO IN Sensitivity: 250/125 mV the interval set at 9 kHz)
Inputs (Digital) (DAV-HDZ278 only) European, Russian, and Middle Eastern models:
TV/VIDEO (COAXIAL IN/OPTICAL IN) 531 kHz - 1,602 kHz (with
Impedance: 75 ohms/- the interval set at 9 kHz)
Outputs (Analog) Australian and New Zealand models:
Phones Accepts low- and high- 531 kHz - 1,710 kHz (with
impedance headphones. the interval set at 9 kHz)
530 kHz - 1,710 kHz (with
the interval set at 10 kHz)
Other models: 531 kHz - 1,602 kHz (with
the interval set at 9 kHz)
98GB
530 kHz - 1,610 kHz (with Taiwan models: 120 V AC, 50/60 Hz
the interval set at 10 kHz) Argentine models: 220 V - 240 V AC,
Antenna (aerial) AM loop antenna (aerial) 50/60 Hz
Intermediate frequency 450 kHz Latin American models: 110 V - 240 V AC,
50/60 Hz
Video Section
Saudi Arabian models: 127 V - 240 V AC,
Outputs VIDEO: 1 Vp-p 75 ohms
50/60 Hz
COMPONENT:
Chinese models: 220 V - 240 V AC,
Y: 1 Vp-p 75 ohms
50/60 Hz
PB/CB, PR/CR: 0.7 Vp-p
Other models: 220 V - 240 V AC,
75 ohms
50/60 Hz
HDMI OUT: Type A (19
Power consumption
pin)
DAV-HDZ278: On: 155 W
Speakers Standby: 0.3 W (at the
Front/Surround (SS-TS80) Power Saving mode)
Speaker system Full range Bass reflex, DAV-DZ270: On: 160 W
Magnetically Shielded Standby: 0.3 W (at the
Speaker unit 65 mm (2 5/8 in) cone type Power Saving mode)
Rated impedance 3 ohms Output voltage (DIGITAL MEDIA PORT)
Dimensions (approx.) 103 mm × 164 mm × 82 (DAV-HDZ278 only) DC 5 V
mm (4 1/8 in × 6 1/2 in × Output current (DIGITAL MEDIA PORT)
Additional Information
3 1/4 in) (w/h/d) (DAV-HDZ278 only) 700 mA
Mass (approx.) 0.6 kg (1 lb 6 oz) Dimensions (approx.) 430 mm × 66 mm × 385
mm (17 in × 2 5/8 in ×
Center (SS-CT80)
15 1/4 in) (w/h/d) incl.
Speaker system Full range Bass reflex,
projecting parts
Magnetically Shielded
Mass (approx.) 4.2 kg (9 lb 5 oz)
Speaker unit 65 mm (2 5/8 in) cone type
Rated impedance 3 ohms
Design and specifications are subject to change
Dimensions (approx.) 265 mm × 93 mm × 71 mm
without notice.
(10 1/2 in × 3 3/4 in × 2 7/8 in)
(w/h/d)
Mass (approx.) 0.7 kg (1 lb 9 oz) • Standby power consumption 0.3 W.
• Halogenated flame retardants are not
Subwoofer (DAV-HDZ278) (SS-WS80) used in the printed wiring boards.
Speaker system Subwoofer Bass reflex • Over 85% power efficiency of
Speaker unit 160 mm (6 3/8 in) cone type amplifier block is achieved with the
Rated impedance 3 ohms full digital amplifier, S-master.
Dimensions (approx.) 205 mm × 325 mm × 325
mm (8 1/8 in × 12 7/8 in ×
12 7/8 in) (w/h/d)
Mass (approx.) 5.2 kg (11 lb 8 oz)
99GB
surround speakers and a center speaker. The
Glossary surround speakers output monaural sound.
DTS
Digital Cinema Auto Calibration Digital audio compression technology
Digital Cinema Auto Calibration was developed developed by DTS, Inc. This technology
by Sony to automatically measure and adjusts conforms to 5.1-channel surround. This format
the speaker settings to your listening comprises of stereo rear channel and there is
environment in a short period of time. discrete subwoofer channel in this format. DTS
Dolby Digital provides the same 5.1 discrete channels of high
This movie theater sound format is more quality digital audio. The good channel
advanced than Dolby Surround Pro Logic. In separation is realized due to the all channel data
this format, the surround speakers output stereo being recorded discretely and processed in
sound with an expanded frequency range, and a digitally.
subwoofer channel for deep bass is HDMI (High-Definition Multimedia
independently provided. This format is also Interface)
called “5.1” with the subwoofer channel HDMI is an interface that supports both video
designed as the 0.1 channel (since it functions and audio on a single digital connection,
only when a deep bass effect is needed). All six allowing you to enjoy high quality digital
channels in this format are recorded separately picture and sound. The HDMI specification
for superior channel separation. Furthermore, supports HDCP (High-bandwidth Digital
since all the signals are processed digitally, less Content Protection), a copy protection
signal degradation occurs. technology that incorporates coding technology
Dolby Pro Logic II for digital video signals.
Dolby Pro Logic II creates five full-bandwidth Interlace format
output channels from 2 channel sources. This is (Interlaced scanning)
done using an advanced, high-purity matrix The Interlace format is the NTSC standard
surround decoder that extracts the spatial method for displaying TV images at 30 frames
properties of the original recording without per second. Each frame is scanned twice -
adding any new sounds or tonal colorations. alternately between the even numbered scanning
x Movie mode lines and then odd numbered scanning lines, at
The Movie mode is for use with stereo television 60 times per second.
shows and all programs encoded in Dolby Parental Control
Surround. The result is enhanced sound field A function of the DVD to limit playback of the
directionality that approaches the quality of disc by the age of the users according to the
discrete 5.1-channel sound. limitation level in each country. The limitation
x Music mode varies from disc to disc; when it is activated,
The Music mode is for use with any stereo music playback is completely prohibited, violent
recordings, and provides a wide and deep sound scenes are skipped or replaced with other scenes
space. and so on.
100GB
is compatible with the 525 or 625 progressive
format.
Super Audio CD
Super Audio CD is a new high-quality audio 2 channel area4)
disc standard where music is recorded in the
DSD (Direct Stream Digital) format
(conventional CD is recorded in the PCM
format). The DSD format, using a sampling
frequency 64 times higher than that of a Multi channel area4) Super Audio CD
conventional CD, and with 1-bit quantization, layer
achieves both a wide frequency range and a wide
dynamic range across the audible frequency
range, and so provides music reproduction 1)You can play the CD layer on a conventional CD
extremely faithful to the original sound.
player.
x Super Audio CD types 2)
Since both layers are on one side, it is not necessary
There are two types of discs, depending on the to turn the disc over.
Super Audio CD layer and CD layer 3)To select a layer, see “To select a playback layer
combination. when playing a hybrid Super Audio CD” (page 39).
Additional Information
4)To
• Super Audio CD layer: A high-density select an area, see “To select a playback area on a
signal layer for Super Audio CD 2 channel + Multi-channel Super Audio CD”
• CD layer1): A layer that is readable by a (page 38).
conventional CD player
Super Audio CD
layer
Hybrid disc2)
(a disc with a Super Audio CD layer and a CD layer)
CD layer3)
Super Audio CD
layer3)
101GB
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
102GB
Index to Parts and Control
For more information, refer to the pages indicated in parentheses.
Front panel
Additional Information
A "/1 (on/standby) (27, 85) G VOLUME control (35)
B A (open/close) (35) H PHONES jack (35)
C Front panel display (105) I AUDIO IN/A.CAL MIC jack (21, 27, 79)
D Play operation buttons (35) J (USB) port (DAV-DZ270 only) (67)
E (remote sensor) (11) K Disc tray (35)
F FUNCTION (30)
103GB
Rear panel
DAV-DZ270
ANTENNA
SPEAKER
FRONT R FRONT L SUR R SUR L
COAXIAL 75
FM AM
SPEAKER
CENTER SUBWOOFER
DAV-HDZ278
ANTENNA
SPEAKER
FRONT R FRONT L SUR R SUR L
COAXIAL 75
FM AM
SPEAKER
DIGITAL IN
CENTER SUBWOOFER
DC5V
COAXIAL OPTICAL 0.7A MAX Y PB/CB PR/CR R AUDIO IN L
TV/VIDEO HDMI OUT DMPORT COMPONENT VIDEO OUT VIDEO OUT TV/VIDEO
104GB
Front panel display
Additional Information
chapter, title, or track number, time
information, radio frequency, playing I Lights up during USB recording/
status, decoding mode, etc. copying. (DAV-DZ270 only) (73)
D Lights up when a station is received. J Lights up when Super Audio CD/CD is
(Radio only) (61) loaded. (38)
E Stereo/Monaural effect (Radio only)
(62)
F Lights up when the HDMI OUT jack is
correctly connected to HDCP (High-
bandwidth Digital Content Protection)
compliant device with HDMI or DVI
(Digital Visual Interface) input. (18)
105GB
Remote control
1)
This button is not available
for this model.
2)The ENTER button has the
same function as the
button. When you operate
the TV, the ENTER button is
used for selecting a channel,
and the button is used for
selecting menu items
(page 80).
3)Except for North American
models.
4)
The button name differs
depending on the area.
5)North American models
only.
6)Thisbutton is only available
for the “DVD” or “USB*”
function.
* DAV-DZ270 only
106GB
Guide to the Control Menu Display
You can use the Control Menu display to select a function and to view related information.
DISPLAY
Additional Information
Press DISPLAY repeatedly.
Each time you press DISPLAY, the Control Menu display changes:
1 t 2 t ... t 1 t ...
The Control Menu display 1 and 2 will show different items depending on the disc type. For details,
see the pages in parentheses.
107GB
Example: Control Menu display 1 when playing a DVD VIDEO.
Currently playing title number1)
Playback status
Total number of chapters2)
Control Menu items (N Playback,
X Pause,
x Stop, etc.)
Options
Function name of selected REPEAT
Control Menu item ENTER Quit: DISPLAY
Operation message
1)
The scene number for a VIDEO CD (PBC is on), track number for a VIDEO CD/Super Audio CD/CD, folder
number for a DATA CD/DATA DVD. DivX video folder number for a DATA CD/DATA DVD (Except for United
Kingdom and North American models).
2)
The index number for a VIDEO CD/Super Audio CD, MP3 file number or JPEG image file number for a DATA
CD/DATA DVD. DivX video file number for a DATA CD/DATA DVD (Except for United Kingdom and North
American models).
3)
Super VCD as “SVCD.”
“MP3” in the Control Menu display 1 or “JPEG” in the Control Menu display 2 for a DATA CD/DATA DVD.
4)
The date is displayed for JPEG image files.
108GB
[TIME] (page 44)
You can check the elapsed time and the remaining playback time.
Input the time code for picture and music searching.
The system displays the DVD/Super Audio CD/CD text or the MP3 file name.
Additional Information
1) 1)
109GB
List of Control Menu Items for USB device
(DAV-DZ270 only)
Tip
• The Control Menu icon indicator lights up in yellow t when you select any item except [OFF]
([PROGRAM], [SHUFFLE], [REPEAT], and [A/V SYNC] only). The [ORIGINAL/PLAY LIST] indicator lights
up in yellow when you select [PLAY LIST] (default setting).
110GB
Index
Numerics F Playable discs 6
Program Play 40
4:3 OUTPUT 54 FM MODE 62
PROGRESSIVE
5.1 Channel Surround 38 Front panel 103
(COMPONENT OUT) 54
Front panel display 82, 105
A Progressive format 29, 100
A/V SYNC 50 H Q
AAC file 67 HDMI
Quick Setup 27
ANGLE 36 YCBCR/RGB (HDMI) 56
ATTENUATE 31 HDMI (High-Definition R
AUDIO 53 Multimedia Interface) 100
AUDIO (HDMI) 56 HDMI RESOLUTION 55 Rear panel 104
AUDIO DRC 57 HDMI SETUP 55 Region Code 8
AUDIO SETUP 57 Remote 11
AUTO CALIBRATION 57, 79, I Repeat Play 42
100 RESET 58, 85
Instant Advance 36
Resume Play 39
Instant Replay 36
B Interlace format 100 S
BACKGROUND 57 INTERVAL 47, 70
BLACK LEVEL 55 SCREEN SAVER 57
BLACK LEVEL J SETUP 52, 85
(COMPONENT OUT) 55 Shuffle Play 41
JPEG image file 45, 67
SLEEP 81
JPEG RESOLUTION 56
C Slide Show 46
L Sound Mode 34
COLD RESET 85
SPEAKER FORMATION 57,
COLOR SYSTEM (VIDEO Language Code List 102
78
CD) 55 LANGUAGE SETUP 53
SPEAKER SETUP 58
CONTROL FOR HDMI 55
M CONNECTION 58
Control Menu Display 107
DISTANCE 58, 59
CUSTOM 52, 85 MENU 53 LEVEL 59
MODE (MUSIC, IMAGE) 47, SUBTITLE 37, 53
D 68, 69 Super Audio CD 38, 101
D. C. A. C. (Digital Cinema MP3 file 45, 67 SYSTEM MENU 26, 31, 32,
Auto Calibration) 79, 100 Multi Session CD 8 62, 81, 82
DATA CD 48 MULTI-DISC RESUME 58 SYSTEM SETUP 57
DATA DVD 48 Multiplex broadcast sound 34
DEC. MODE 32 T
DEMO 26 N
TEST TONE 59
DIGITAL MEDIA PORT 76 Naming preset stations 62 TIME 44
DIMMER 82 NIGHT 81 TRACK SELECTION 57
DISPLAY 63
TV TYPE 54
DivX® 48, 58 O
Dolby Digital 37, 100 ORIGINAL 43 U
Dolby Pro Logic II 100 OSD 53
Dolby Surround Pro Logic 100 USB device 67
DTS 37, 100 P V
DUAL MONO 34 PARENTAL CONTROL 50,
DVD’s menu 43 VIDEO SETUP 54
58, 100 VOLUME LIMIT 56
DYNAMIC BASS 81 PAUSE MODE 55
E PBC Playback 39 W
PICTURE NAVI 46, 69 WMA file 67
EFFECT 47, 70 PLAY LIST 43
111GB
(1)