Professional Documents
Culture Documents
Experiment 3 Fajans Determination of Chloride
Experiment 3 Fajans Determination of Chloride
The volume in mL of AgNO3 solution required to reach the equivalence point is symbolized by v*.
Thus, v*C is the number of millimoles of AgNO3 required to react with all of the chloride present in
the titration sample and because 1 mmole of AgNO3 reacts with 1 mmole of chloride, v*C is also
equal to the number of millimoles of chloride present. The weight of chloride present is then mmole
Cl- x 35.453 mg/mmole =( v*C x 35.453) mg.
How will we establish the equivalence point volume of AgNO3 in the titration of chloride?
We will not. The equivalence point is a quantity that exists only in theory and in text books. In the
world we must satisfy ourselves with the "endpoint" which is an experimental estimate of the
equivalence point. Our objective in a titration analysis is to match the experimental endpoint as
closely as possible with the theoretical equivalence point. Just how this is to be accomplished
depends on the amounts and nature of the substances involved in the analysis as well as the amounts
and nature of other substances present in the sample. In any case we will assume that the
experimental endpoint is an accurate approximation to v*.
The Fajans analysis for chloride employs a color-change indicator, dichlorofluorescein, to
signal the endpoint of a titration of chloride ions with a "standard" AgNO3 solution. We will
assume that the visual endpoint of this titration is also the equivalence point and use this assumption
to calculate the quantity of chloride present in an unknown sample. In other words, the analysis
depends on two quantities: the concentration of "standard" AgNO3 solution and the endpoint
volume v*, as follows.
The AgNO3 Standard
In the experiment that follows we will use a AgNO3 solution of known concentration - a
standard AgNO3 solution. This has been prepared in one of two ways. The first involves weighing
out an appropriate amount of very pure solid AgNO3 then dissolving and diluting to an accurately
known volume. The resulting solution is said to employ AgNO3 as a "primary standard". A
second and preferable procedure involves analyzing a AgNO3 solution by titrating carefully weighed
samples of pure NaCl whose chloride content is known. From the measured endpoint volume and
known amount of chloride, C is calculated. In this case the AgNO3 solution is said to have been
"standardized against a primary standard of NaCl" or, more simply, "standardized against NaCl".
The first of these methods is certainly simpler but it is not widely applicable because it
depends on the availability of the titration reagent in very pure form. Additionally, this approach
relies heavily on the assumption that the experimental endpoint volume really does accurately
approximate the equivalence point volume.
The second approach of standardizing against a standard sample is more commonly used and
has the advantage of allowing for some "cancellation" of errors. This method is essential with
complex analyses.
We continue with a brief description of the dichlorofluorescein indicator to be used to signal
the titration endpoint.
The Indicator Reaction
Consider the process of adding AgNO3 solution to a sample solution held in a flask and
containing chloride ions. At the start, when only a small amount of AgNO3 has been added, the
solution contains some AgCl precipitate, a very small concentration of Ag+ ions and an excess of Cl-
ions. (Cl- ions are just floating around "waiting" for the addition of more AgNO3.) When we have
added just enough AgNO3 to reach the equivalence point the solution in the flask contains AgCl and
very small and equal concentrations of Ag+ and Cl- ions. If we continue to add more AgNO3 to the
flask very little additional AgCl is produced but the mixture now contains an excess of Ag+ ions.
That is, the Ag+ ion concentration is now greater than the Cl- concentration in the solution. Thus, the
solution in the flask, the "analyte solution", is fundamentally different before and after the
equivalence point. Before the equivalence point [Cl-]>[Ag+], but after the equivalence point
[Ag+]>[Cl-]. We may take advantage of this change in the environment of the analyte solution.
It is a general property of ionic precipitates like AgCl to adsorb their own ions from solution.
Thus, a silver chloride precipitate standing in a solution containing excess chloride ions causes a
layer of chloride ions to adhere to its surface. Likewise, AgCl in the presence of a solution
containing excess Ag+ ions forms an adsorbed layer of Ag+. If the solution contains
dichlorofluorescein anion, some of this material will be adsorbed onto the layer of Ag+ ions present
at the precipitate surface and form the red color of silver dichlorofluoresceinate. This silver salt
would not ordinarily form in very dilute solutions of Ag+ and dichlorofluorescein anion. However,
adsorption of Ag+ at the silver chloride precipitate surface results in a locally high concentration of
Ag+ which is capable of precipitating red silver dichlorofluoresceinate onto the precipitate surface.
The dichlorofluorescein is termed an adsorption indicator and here signals the first presence of
excess Ag+ in the solution. This occurs immediately after the equivalence point as AgNO3 is added
to the Cl- solution. Consequently, the appearance of the first persistent reddish color in the mixture
indicates the endpoint in this titration.
2. Zero (tare) the analytical balance with a clean dry, capped weighing bottle. Add 1.1 to 1.3 g. of
your chloride sample to the bottle; replace the cap and weigh as accurately as possible. Record on
your data sheet.
3. Rinse a 250 mL volumetric flask with distilled water and quantitatively transfer the chloride
sample to the flask. (The instructor will demonstrate.) Dissolve the sample and dilute to the mark.
Mix thoroughly.
4. Into each of five 200 - 250 mL erlenmeyer flasks carefully pipet 20.00 mL of your chloride
sample. (Remember to rinse the pipet with the sample solution before the first transfer.) Use a
graduated cylinder to add about 10 mL of 1% dextrin solution and about 20 mL of distilled water to
each flask.
5. Rinse and fill a 50 mL buret with 0.04 F AgNO3 solution. This solution is not exactly 0.04 F in
AgNO3. Its concentration is labeled on the bottle. Record the value on the data sheet. Tap to
remove bubbles and make certain that the buret tip is filled with solution. Adjust the solution level
between 0 and 2 mL; read the buret to the nearest 0.01 mL. (Do not try to set 0.00 mL!) Record the
initial reading.
6. Add 3 - 4 drops of dichlorofluorescein indicator solution to the first sample flask and titrate to the
first appearance of a persistent faint pink color. Read the buret to the nearest 0.01 mL and record
the value on your data sheet. Repeat the procedure with the other samples. You should have three
endpoint volumes within a range of 0.1 - 0.2 mL. If this is not the case, prepare a few more sample
solutions and repeat the titrations.
7. Empty the contents of the titration flasks as well as any excess AgNO3 solution into a waste
container. (There are large bottles in the fume hoods for this purpose.)
8. Rinse the buret, pipet and volumetric flask with several portions of distilled water and put them
away. Use a brush and soapy water to wash the erlenmeyer flasks. (SCRUB!)
4. Suppose that you made a very, very large number of titrations with the same sample. Within
what range would the mean percentage chloride lie with 90% probability? (That is, what is the 90%
C.I. for the mean % Cl? From what % to what %?)
6. A silver nitrate solution is standardized by titrating a known weight of pure NaCl. Exactly 31.20
mL of the solution titrates a 0.1550 g sample of NaCl (FW = 58.44 g/mL). The same silver nitrate
solution is used to titrate a sample that contains only NaCl and KCl (FW = 74.56 g/mol). A 0.1400
g sample of the NaCl, KCl mixture is titrated by 24.70 mL of the AgNO3 solution.
a. What is the concentration of the AgNO3 solution?
b. What percentage by weight of NaCl is present in the NaCl, KCl mixture? (Note: The
weight of the sample is the sum of weights of NaCl and KCl. The number of moles of chloride
present is the sum of the number of moles of NaCl and KCl.).