Professional Documents
Culture Documents
Air Drill 8843914 PDF
Air Drill 8843914 PDF
0 8843914
Please read and understand all instructions before use. Retain this manual for future reference.
8843914 3/8 in. Angled Air Drill V1.0
SPECIFICATIONS
Max. Pressure 90 PSI
Air Consumption @ 90 PSI 3.36 CFM
No Load Speed 1,900 RPM
Chuck Size 3/8 in.
Chuck Type Keyed
Air Inlet 1/4 in. NPT
Min. Hose Size 3/8 in.
Reversible No
Material Die-cast Aluminum Housing
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A notice is
an alert that there is a possibility of property damage, injury or death if certain
instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that will
result in severe personal injury or death if the proper precautions
are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that could
result in severe personal injury or death if the proper precautions
are not taken.
CAUTION! This notice indicates a potentially hazardous situation that may result in
minor or moderate injury if proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will
result in equipment or property damage, but not personal injury.
INTRODUCTION
The 3/8 in. Angled Air Drill is ideal for home improvement projects, autobody work and
general assembly or repairs. The angled barrel fits into narrow and hard-to-reach spaces.
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal
injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection and
maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-lit and
free of distractions. Place lights so you are not working in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from the
work area.
3. Store unused tools properly in a safe and dry location to prevent rust or
damage. Lock tools away and keep out of the reach of children.
4. Do not install or use in the presence of flammable gases, dust or liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the Canadian
Standards Association (CSA) or American National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side protection for
the eyes. Eye protection equipment should comply with CSA Z94.3-07 or
ANSI Z87.1 standards based on the type of work performed.
2. Wear the appropriate type of full-face shield in addition to safety googles, as
the work can create chips, abrasive or particulate matter.
3. Wear gloves that provide protection based on the work materials or to reduce
the effects of tool vibration.
3.1 Do not wear gloves when operating a tool that can snag the material
and pull the hand into the tool.
4. Wear protective clothing designed for the work environment and tool.
5. Non-skid footwear is recommended to maintain footing and balance in the
work environment.
6. This tool can cause hearing damage. Wear hearing protection gear with an
appropriate Noise Reduction Rating to withstand the decibel levels.
7. The tool may contain high pressure. Use safety glasses and gloves for
protection during operation. Keep hands clear of the exposed rubber portions
of the hose.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid personal
injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs, alcohol or
medications.
2. Avoid wearing clothes or jewelry that can become entangled with the moving
parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and balance enables
better control in unexpected situations.
4. Support the workpiece or clamp it to a stable platform. Holding the workpiece
by hand or against your body may lead to personal injury.
5. Keep your fingers away from the trigger/switch while carrying the tool, attaching
an air hose or an accessory. Lock the trigger/switch safety if available.
6. Avoid unintentional starts. Be sure that the regulator/throttle switch is in the neutral
or OFF position when not in use and before connecting it to any air source.
7. Serious injury or death may occur from inhaling compressed air. The air
stream may contain carbon monoxide, toxic vapors or solid particles. Never
inhale compressed air directly from the pump or air tool.
5. After changing the bits and accessories or making adjustments, make sure
the chuck and any other adjustment devices are securely tightened. Loose
adjustment devices will be violently thrown.
6. Always check accessory bits for damage before each use. Damaged
accessories can break during use and cause serious injury.
7. Never use dull or damaged bits. Sharp bits must be handled with care.
Damaged bits can snap during use. Dull bits require more force to push the
tool, possibly causing the bit to break.
8. If devices are used for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of a dust
collection system reduces dust-related hazards.
9. Maintain a firm grip on the tool and position your body and arms to allow you
to resist kickback forces. Kickback will propel the tool in the direction
opposite to the tool’s movement at the time of snagging.
10. Use metal and voltage detectors to locate hidden electric, water or gas lines.
Avoid touching live components or conductors.
11. Before drilling, check that there is sufficient clearance for the drill bit under
the workpiece.
12. If you are interrupted when operating the drill, complete the process and
switch off the tool before looking up.
7. Turn OFF the valve and discharge any remaining air pressure after each use
or before adjusting the tool.
8. Do not leave the air tool unattended with its compressed air supply on. Turn
off the compressed air supply and bleed the air tool of any remaining
compressed air before leaving the air tool unattended.
9. Serious injury may occur from loose debris being propelled at high speeds
from the compressed air stream. Always wear OSHA approved safety
glasses to protect the eyes during operation of the air compressor.
10. Never point the air stream or tools at any point of your body, other people or
animals. Debris and dust may be ejected without warning. Always turn off the
air compressor and drain tank pressure completely before attempting
maintenance or attaching air tools. Release pressure slowly from the system.
AIR HOSE PRECAUTIONS
1. Inspect the tool's air hose for cracks, fraying or other faults before each use.
Discontinue use if the air hose is damaged or hissing is heard from the air
hose or couplers. Replace the defective air hose.
2. Do not allow people, mobile equipment or vehicles to pass over the unprotected air
hose. Position the air hose away from high traffic areas, in a reinforced conduit or
place planks on both sides of the air hose to create a protective trench.
3. Prevent damage to the air hose by observing the following:
3.1 Never carry the tool by the air hose.
3.2 Keep the air hose behind the tool and out of the tool's work path.
3.3 Keep the air hose away from heat, oil, sharp edges or moving parts.
3.4 Do not wrap the air hose around the tool as sharp edges may pierce or
crack the air hose. Gently coil the hose and either hang on a hook or
fasten with a device to keep hose together when storing.
4. A damaged or disconnected air hose under pressure may whip around and
inflict personal injury or damage the work area. Secure the compressor's air
hose to a fixed or permanent structure with clamps or cable ties.
COMPRESSOR/TANK PRECAUTIONS
DANGER! Do not use an air tank beyond its expiration date. A tank rupture
or explosion may kill or cause a serious injury to yourself or a bystander.
Disable and discard the air tank according to the your municipality by-laws.
1. Never drill into, weld, patch or modify the air tank. Immediately replace the tank
or compressor if an air leak develops. The leak may lead to a rupture.
DRILLING PRECAUTIONS
CAUTION! Immediately release the trigger if the drill bit becomes stuck or
jammed. The tool’s torque can twist your arm and cause an injury. The tool
may twist out of your grip and cause an injury to yourself or a bystander.
The term bit refers to any drill bits, router bits or tool accessories that penetrate a
material and creates a cavity through a rotary motion.
1. Verify the drill’s rotation before starting the drill.
2. A loose or mismatched bit may be ejected by the tool, causing an injury to
the user or a bystander. It may also fail to penetrate the material as the point
may move around under pressure, damaging the workpiece.
2.1 Ensure the bit shank size matches the tool’s chuck or collet size.
2.2 Tighten the chuck or collet so the shank is tightly held with no room to
move.
3. Always hold the tool firmly in your hands before switching the tool ON. The
reaction to the motor’s torque may cause the tool to twist, as it accelerates to
full speed.
4. Do not use drill as a router or try to elongate or enlarge holes by twisting the
drill. Drill bits can break and can cause injury.
5. Do not apply side pressure on the bit unless it is designed for such a
purpose. The bit may bind or break.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a
malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
Make sure that all items in the contents are included.
Contents: • Air Drill • Chuck Key
IDENTIFICATION KEY
A Chuck Jaws
B Chuck
C Angle Head
D Trigger Lever Safety
E Air Regulator
F Trigger Lever
G Air Inlet
OPERATION
PRESSURE DROP
Apply the air consumption and pressure rate numbers to the tool’s air inlet, not the
compressor’s outlet. Calculate the pressure drop for your air supply set-up and
increase the compressor outlet pressure to compensate. Make sure you do not
exceed the maximum pressure for any part of your air supply system.
Installing a pressure gauge at the tool inlet is the best way to measure the air
pressure and adjust the compressor’s output.
TOOL OPERATION
1. Clean the air drill of packing grease before first use. See the Air Tool
Lubrication section for instructions.
2. Install a drill bit into the chuck jaws (A) and hand-tighten. Make sure the bit’s
shaft is straight. Tighten using the chuck key. Remove the chuck key.
3. Connect the air drill to the end of the air hose.
4. Set the compressor to the correct air pressure and flow (see Specifications).
Start the compressor.
5. Test the drill under no load to confirm the bit is installed correctly.
5.1 Push the trigger safety lever (D) forward.
5.2 Rotate the air regulator (E) to adjust the drill speed.
5.3 Release the trigger lever and the safety will spring back into place.
6. Place the drill bit point onto the workpiece surface.
6.1 Use a center punch to mark the spot to prevent the drill bit from
skittering across the surface.
6.2 A larger drill bit may require a pilot hole. Use a narrower bit to drill the
pilot hole first, then install the larger bit.
6.3 Apply a drop of cutting oil to the drill bit and surface before cutting metal.
7. Squeeze the trigger and lightly push the drill against the workpiece. Allow the
bit to cut the material. Continue to apply gentle pressure until the proper
depth is reached.
8. Hold the trigger until the drill bit is removed from the hole, then release the trigger.
9. Shut the compressor off once the task is completed. Squeeze the trigger to
release residual compressed air from the hose and tool. Disconnect the tool.
10. Remove the bit and store both the bit and the drill.
STORAGE
When not in use for an extended period, apply a thin coat of lubricant to the steel
parts to avoid rust. Remove the lubricant before using the tool again.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.
IMPORTANT! DO NOT pollute the environment by allowing uncontrolled
discharge of waste oil.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function
properly or parts are missing. If unable to do so, have a qualified technician
service the tool.
PARTS BREAKDOWN
PARTS LIST
# DESCRIPTION QTY ASSY 12 Throttle Lever 1
1 Housing 1 13 O-Ring 1 D
2 Valve Stem 1 14 O-Ring 1 D
3 O-Ring 1 A, E 15 Exhaust Block 1 D
4 O-Ring 1 A 16 Exhaust Deflector 1 D
5 O-Ring 2 A.E 17 Muffler cover 1 D
6 Screw 1 E 18 Air Inlet Bushing 1
7 O-Ring 1 E 19 Handle Grip Ass'y 1
8 Spring 1 E 21 Ball Bearing 1 B
9 O-Ring 1 A.E 22 Rear End Plate 1 B
10 Throttle Lever Pin 1 23 Cylinder 1
11 Speed button 1 E 24 Spring Pin 2 B, C
ASSEMBLIES
# DESCRIPTION QTY
A Consumable parts repair kits 1
B Rear End Plate Assembly 1
C Front End Plate Assembly 1
D Exhaust Deflector Assembly 1
E Switch Group 1
F Idle Gear Seat Assembly 1
G Gear Assembly 1