Professional Documents
Culture Documents
FM Global Property Loss Prevention Data Sheets: List of Figures
FM Global Property Loss Prevention Data Sheets: List of Figures
Table of Contents
Page
List of Figures
Fig. 1. Automatic hinged damper at junction of branch duct with main vertical duct. .................................. 4
Fig. 2. Fire damper requirements at duct shafts and other fire separations. ................................................ 4
Fig. 3. Typical smoke control arrangement by using pressurization-exhaust method. ................................ 5
Fig. 4. Automatic fire door in duct at major fire separation. ......................................................................... 6
©2001 Factory Mutual Insurance Company. All rights reserved. No part of this document may be reproduced,
stored in a retrieval system, or transmitted, in whole or in part, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without written permission of Factory Mutual Insurance Company.
1-45 Air Conditioning and Ventilating Systems
Page 2 FM Global Property Loss Prevention Data Sheets
1.0 SCOPE
This data sheet examines the hazards associated with air conditioning and ventilating systems. The standard
provides guidelines to prevent or restrict the spread of fire, smoke, and heat through the air conditioning
system.
This data sheet is particularly applicable to occupancies most susceptible to smoke damage. These include:
large commercial and public buildings, stores and shopping centers, health facilities, data processing areas,
clean areas, printing operations, textile processing, photographic material processing, food processing, and
electronic and semi-conductor industries.
Guidelines also are provided to prevent moisture from contaminating hospital operating and surgical supply
rooms caused by the air conditioning chillers. Contamination of clean rooms also is an important issue; refer
to Data Sheet 7-7/17-12, Semiconductor Fabrication Facilities.
1.1 Changes
January 2001. This revision of the document has been reorganized to provide a consistent format.
2.1.1 Ducts
2.1.1.1 Use ducts constructed of steel, aluminum, concrete, masonry, or Factory Mutual Research Approved
(see Appendix A, for definition) materials.
2.1.1.2 Duct linings and coverings should be of noncombustible material, or of material Approved by Fac-
tory Mutual Research. The lining should be interrupted at fire dampers so as not to interfere with their
operation. Lining and coverings also should be interrupted at the heat source area in a duct system containing
electric resistance or fuel burning heaters.
2.1.1.3 Duct coverings should not extend through walls or floors that need a fire-resistive rating.
2.1.1.4 An attic, basement, or concealed space may be an integral part of a duct system, but it should be
protected from fire hazards.
2.1.1.5 Do not use hallways as plenums.
2.1.1.6 The clearance between metal ducts and stored combustible material should be at least 6 in. (150
mm). The clearance between metal ducts and combustible construction should be at least 2 in. (50 mm).
2.1.1.7 Where ducts pass through walls and floors serving as fire subdivision, the opening in the construc-
tion around the duct should not exceed 1⁄2 in. (13 mm) average clearance on all sides, and should be
firestopped by packing with mineral wool or other noncombustible material to prevent the passage of flame
and smoke.
2.1.1.8 Ducts that pass through concealed spaces of combustible construction or that are located inside com-
bustible partitions or walls should be protected with 1⁄4 in. (6 mm) noncombustible insulating material, or a
clearance of 2 in. (50 mm) should be maintained between ducts and all combustible construction. Fill the
spaces between the ducts and the combustible construction solidly with brick, mineral wool, or other
noncombustible material. The integrity of firestopping at penetrations should be maintained.
2.1.1.9 Ducts that pass through more than one floor needing protection of vertical openings should be
enclosed with walls of fire rating equal to that of the floors. A fire-resistive shaft used as a duct need not be
additionally enclosed (Figs. 1, 2 & 3).
a) The enclosure of ducts is not required for branches that are cut off from the main portion of the duct
by fire dampers (Fig. 2).
b) When ducts extend through only one floor, and fire dampers are installed at each point where the floor
is penetrated, the fire dampers may be accepted in lieu of the enclosure.
c) Two or more ducts serving separate floors should not be located within the same fire-resistive enclosure
unless fire dampers are installed where each branch extends from the enclosure.
Fig. 1. Automatic hinged damper at junction of branch duct with main vertical duct.
Fig. 2. Fire damper requirements at duct shafts and other fire separations.
2.1.1.10 Ducts should not be installed adjacent to unprotected structural members. To be effective, tructural
members should be fireproofed before adjacent ductwork is installed.
2.1.1.11 Design and install ducts in accordance with national trade association specifications.
Note: The Sheet Metal and Air Conditioning Contractors National Association Inc. (SMACNA) publishes
design and installation specifications for metal and fibrous glass ducts.
Fig. 3. Typical smoke control arrangement by using pressurization-exhaust method. Fire is in Floor No. 3. Dampers SD1,
SD2, SD4, SD5, and ED3 remain open. Dampers SD3, ED1, ED2, ED4, and ED5 will close. (section view)
Fig. 4. Automatic fire door in duct at major fire separation. Duct to be independent of fire separation.
2.1.2.3 a) Factory Mutual Research does not presently approve fire dampers. Equip walls that have less than
three hours fire resistance with automatic fire dampers of either the solid or louvered type (Figs. 1,
5 & 6).
b) Install automatic fire dampers either at the outlet and inlet openings in the main vertical duct, or
at the duct penetration in walls or floors serving as fire subdivisions (Fig. 2).
c) For solid type dampers, use No. 16 U.S. ga (1.6 mm) steel on ducts up to 18 in. (455 mm) in diam-
eter or longest dimension, No. 12 U.S. ga (2 mm) for ducts up to 36 in. (910 mm) in diameter or longest
dimension, and No. 7 U.S. ga (4 mm) for ducts above 36 in. (910 mm) in diameter or longest
dimension.
d) Louvered-type automatic dampers should be constructed of No. 18 (1.3 mm) U.S. ga steel provided
the individual louvers are not over 6 in. (150 mm) wide and stiffened by formed edges.
2.1.2.4 Arrange fire doors and fire dampers to close automatically, in the direction of the air movement when-
ever possible, and to remain tightly closed upon operation of a fusible link, other Approved heat-actuated
devices, or Approved smoke detectors. Fusible links should have a temperature approximately 50°F (28°C)
above the maximum temperature that would normally be encountered within the system, but not less than
165°F (74°C).
2.1.2.5 Hinged fire doors and dampers should be equipped with spring catches to hold them closed, and
pins of hinges should be made of corrosion-resistant material.
2.1.2.6 When the damper is intended for both fire-stopping and smoke-stopping, use combination smoke
detectors (sensitive to both heat and smoke) for activation.
2.1.2.7 When fire dampers and doors are designed to serve the dual function of fire-stopping and smoke-
stopping, special features such as gaskets should be furnished to provide adequate sealing against any
smoke leakage.
2.1.2.8 Design fire doors and dampers at duct openings in fire walls or at floor levels so that the destruc-
tion of the duct will not affect the operation of fire walls or dampers. This can be accomplished by mounting
the units in the fire wall or floor opening by a collar held in place with perimeter angles on each side of the
opening. Then the ductwork is brought into the collar but not through the opening (Figs. 1, 4, 5, 6 & 7).
Fig. 7. Combination fire and smoke dampers. Operation: (A) Fire damper mode: high temperature
melts fusible link closing fire damper. (B) Smoke damper mode: smoke detector upon sens-
ing heat/smoke actuates damper motor to close damper. (Sheet Metal and Air Conditioning
Contractors National Association, Inc.)
2.2 Protection
2.2.1 In cases where there is the possibility of accumulation of combustible contaminants in the
noncombustible filtering system, the following should be done:
a) Provide sprinkler protection in filter systems with capacities of 10,000 ft3/min (283 m3/min) and above.
Arrange the sprinklers to wet the entire surface of the filters upon operation. Sprinklers should be on a del-
uge system using ordinary hazard pipe schedule. Activation should be by combination smoke detectors
(sensitive to heat and smoke) arranged in accordance with Data Sheet 5-48, Automatic Fire Detectors.
b) To prevent smoke spread from the filters to the conditioned areas, the following should be done:
i) Provide a one-hour rated fire door or damper downstream from the filters (Fig. 8). The door or damper
should be arranged for closing by the activation of combination smoke detectors. Arrange the smoke
detectors in accordance with Data Sheet 5-48. The system should not be cross-zoned. (The same
detection system can be used to activate the deluge system.)
ii) Install an exhaust fan to exhaust the smoke to the outside in case of a fire in the filters. The exhaust
fan should be activated by combination smoke detectors (Fig. 8).
iii) Arrange the supply and return fans of the air conditioning system to shut down on activation of
combination smoke detectors.
c) Filters with capacity less than 10,000 ft3/min (283 m3/min) should be protected in accordance with
Recommendation No. 2.2.1 b above.
2.2.2 Combustible filters in an air conditioning system should be protected as follows:
a) Provide sprinkler protection in filtering systems with capacity over 5000 ft3/min (142 m3/min) in
accordance with Recommendation No. 2.2.1 a.
b) To prevent smoke spread from the filters to the conditioned areas, protection should be provided in
accordance with Recommendation No. 2.2.1 b.
Fig. 8. Typical smoke control arrangement for filter fires. (plan view)
c) Filters with capacity less than 5000 ft3/min (142 m3/min) should be protected in accordance with
Recommendation No. 2.2.1 b.
2.2.3 As an alternative to Recommendation No. 2.2.1 b, the return-exhaust fan and other equipment (damp-
ers, etc.) of the air conditioning system should be designed to exhaust the smoke from a filter fire as shown
by Figure 9.
2.2.4 Provide adequate drainage in the filter assembly when sprinklers are installed. (Refer to Data Sheet
7-78, Industrial Exhaust Systems.)
2.2.5 Combustible environments and electrical wiring or combustible pneumatic tubing should preferably
not be present in air conditioning ducts. However, when the presence of combustible materials in the air con-
ditioning system is absolutely necessary, or when the ducts themselves are combustible, provide sprinkler
protection as recommended in Data Sheet 7-78, Industrial Exhaust Systems.
Fig. 9. Mode of operation of the air conditioning system in case of fire in the filters.
f) When mounting equipment, dampers, control motors, etc., the fibrous glass duct system should be
adequately reinforced and supported to accommodate the additional weight of material and equipment
without damage to the duct material.
g) Do not use fibrous glass ducts outdoors.
h) Use fibrous glass ducts only in areas of noncombustible construction and occupancy. In areas of com-
bustible construction or combustible loading, fibrous glass ducts may be used if sprinkler protection is
provided in these areas, and the ducts are not used for smoke control.
2.4.2 Ducts should be made reasonably tight throughout and should have no openings other than those
required for proper operation and maintenance of the system. Wired glass may be used for inspection
windows in ducts.
2.4.3 Construct plenums and ducts, other than vertical ducts, so that the interior is accessible for cleaning
accumulations of dust and combustible material. Provide cleanout openings at approximately 20 ft (6 m) inter-
vals and at changes of direction. Removable grills are acceptable as cleanout openings. When plenums
pose fire and smoke hazards, protection should be provided as recommended in Recommendation No. 2.4.6
under Section 2.4 ‘‘Operation and Maintenance’’ and Recommendation No. 2.2.5 under Section 2.2
‘‘Protection.’’
2.4.4 Provide suitable hand-hole openings with tightly fitted covers near the fire doors or dampers to make
them accessible for inspection and maintenance.
2.4.5 Install fans to be readily accessible for inspection and maintenance. They should be secured to
substantial supports.
2.4.6 To control smoke, do the following:
2.4.6.1 The air conditioning system can be designed to control smoke and thus lessen smoke damage by
using any one of the following methods.
a) Pressurization-Exhaust Method. The air conditioning system in this method is designed to switch to
a smoke control mode upon detection of smoke in the fire area (Fig. 3). This operation automatically puts
the fire area under exhaust, and areas adjacent to the fire into supply. To accomplish this, the return-
exhaust damper(s) in the fire area should remain open, and the supply damper(s) should close on smoke
detection. In all other areas adjacent to the fire, the supply dampers should remain open and the exhaust-
return dampers should close on smoke detection. The intent is to prevent smoke spread to the adjacent
areas of the fire and purge the smoke from the fire area via exhaust (Fig. 3).
b) Pressurization Method. The pressurization method can be used to protect a property against smoke
damage from exposure fires. This can be accomplished by designing the air conditioning system of the
exposed property to pressurize it by maintaining the supply damper(s) on the open position and closing the
exhaust damper(s) on smoke detection (Fig. 10).
Fig. 10. Typical smoke control arrangement by pressurizing the protected area. (plan view)
2.4.6.2 Design the smoke-control system to maintain the areas adjacent to the fire area with a pressure of at
least 0.20 in. water gauge (50 Pa) higher than the fire area.
2.4.6.3 Activation of the smoke-control system should be by Approved smoke detectors located within the
zone covered by the specific smoke-control system. Arrange the type, location and spacing of detectors in
accordance with Data Sheet 5-48, Automatic Fire Detectors.
2.4.6.4 Evaluate duct materials and other air conditioning equipment for their fire hazards, their ability to con-
vey smoke and gases, their ability to withstand additional pressure (both positive and negative) by the supply
and exhaust systems, and their ability to maintain structural integrity under fire exposure conditions.
Guidelines for suitable materials can be found in Data Sheet 7-78, Industrial Exhaust Systems.
2.4.6.5 Dampers used for the smoke control arrangement should have the dual function of stopping both
fire and smoke, and should be equivalent to the fire resistance rating of the assembly (Fig. 7).
2.4.6.6 Supply and exhaust ducts serving one smoke zone should not pass through another smoke zone,
unless they are enclosed in a fire-smoke resistant enclosure (Fig. 3).
2.4.7 Examine the fresh-air intake when ducts are inspected. Items to be noted are accumulations of com-
bustible material near the intake, presence of buildings or structures that may present an exposure to the
intake allowing smoke and fire to be drawn in, and the operating condition of any automatic damper designed
to protect the opening against exposure fire.
2.4.8 If accumulations of combustible material are noted, remove them immediately, and make arrange-
ments to avoid further accumulations. Inspections should thereafter be made more frequently. If newly erected
exposures are present, provide adequate protection at the intake.
2.4.9 Make quarterly inspections to determine the amount of dust and waste material in the ducts (both dis-
charge and return). If after several inspections such frequent inspection is found unnecessary, adjust the
interval between inspections to suit the conditions.
2.4.10 Clean ducts whenever inspection indicates the need. Cleaning may be by vacuum or hand brushing.
2.4.11 Clean cooling and heating coils, if necessary, at the time the ducts are cleaned.
2.4.12 Inspect plenum chambers monthly. If after several inspections such frequent inspection is found
unnecessary, adjust the interval between inspections to suit the conditions.
2.4.13 Plenum chambers should be cleaned whenever inspection indicates the need. Do not use plenum
chambers for storage.
2.4.14 Keep all air filters free of excess dust and combustible material. Unit filters should be renewed or
cleaned when the resistance to air flow has increased to two times the original resistance, or when the resis-
tance has reached a value of recommended replacement by the manufacturer. A suitable draft gauge is
advised for the purpose. Draft gauges of a type that will operate a warning light or produce an audible sig-
nal when excessive dust loads have accumulated, are recommended. If the filters are of the automatic
liquid-adhesive type, sludge should be regularly removed from the liquid-adhesive reservoir.
2.4.15 Filters designed to be thrown away after use, should never be cleaned and re-used.
2.4.16 Check the system activating devices, such as fusible links, heat and smoke detectors, and electric
thermostats to see that they are not loaded with residue or otherwise impaired.
2.4.17 Adequately trained personnel should inspect and test heat and smoke detector systems.
Manufacturer’s or installer’s recommendations should be followed in maintaining, inspecting, and testing
the equipment.
2.4.18 Arrange the overall system so that it can be adequately tested every six months by simulating
emergency mode conditions.
2.4.19 All equipment requiring servicing and testing should be readily accessible. Provide practical means
for adequate cleaning.
2.4.20 Exercise care in the use of liquid adhesives. Use of an adhesive of low flash point would create a
serious hazard.
2.4.21 Inspect electrical equipment of automatic filters monthly, observing the operation cycle to see that
the motor, relays, and other controls function as intended. Drive motors and gear reductions should be
inspected at least semiannually, and lubricated when necessary.
2.4.22 Inspect fans and fan motors at least quarterly, and clean and lubricate when necessary. Avoid allowing
oil to run onto the fan blades. Check fans for alignment, and to see that they are running freely.
2.4.23 Examine automatic fan controls at least once a year to see that they are in operable condition.
2.4.24 Examine each fire door and fire damper once a year to see that it is in good operating condition, giving
attention to hinges and other moving parts.
2.4.25 Never perform cutting and welding operations on ductwork containing combustible deposits except
as a last resort, and then only after a thorough cleaning. The FM Global Hot Work Permit System for cutting
and welding should be used.
2.4.26 The use of an inspection form to obtain a thorough inspection is recommended. The form should apply
to the system or systems involved, listing the items needing attention.
2.4.27 To control moisture in the system, do the following:
2.4.27.1 The air handler supply fans serving hospital surgical areas should preferably be interlocked with
air handler cooling coil temperature, or with chilled water flow and temperature at the chiller. If the coil tem-
perature is high (about 10% over setpoint), or if either chilled water flow is low or chilled water temperature
is high, the fan should shut down and not start until chilled water conditions are within an acceptable range.
Note that paddle- or sail-type flow switches are commonly used and are not as reliable as other types of flow
sensors such as differential pressure transmitters; a broken paddle can shut down the chiller.
An alternative would be to interlock the chiller unit to shut down the fan. However, the supply fan should
not start (by operating procedure or startup permissive) until the chilled water temperature has reached its set-
point. If two chillers are used, shutdown (safety control shutdown) of either one should cause a fan trip (since
one chiller might not carry the load) unless there is also a chilled water temperature shutdown interlock in
series with the chiller interlocks which can then be in parallel. Shutdown of both chillers, manual or automatic,
should cause a fan trip.
If there is a backup system such as a direct expansion (refrigerant) coil that can be put on line quickly and
automatically, the chilled water interlocks need not shut down the fan. They will be needed to initiate startup
of the backup cooling system, however, and also can be used as a startup permissive for the air handler supply
fan(s).
The chilled water interlocks can be bypassed during winter months if there is no danger of hot, humid out-
side air (depending upon geographic location). If an outside dewpoint transmitter is installed, this device can
be used in parallel with the chilled water interlocks; if the outside dewpoint remains below the lowest
anticipated indoor room temperature, the fan can operate.
2.4.27.2 Provide reheat to control humidity, using either local coils or a central reheat coil. Reheat should
be kept in service. Never mix humid outside air with conditioned air. See Figure 11. Develop a contingency
plan for repair/replacement of reheat coils.
2.4.27.3 Protect the chilled water system with a relief valve to prevent overpressurization caused by a faulty
makeup water valve. Overpressurizing the pipes has caused underground pipe cracking and an unexpected
shutdown of the chillers.
This subject is also covered in NFPA 90A. This data sheet covers the problems posed by fire, heat, and
smoke spread through the air conditioning system in more detail than the NFPA standard. It also recommends
methods for control of these problems.
2.5 Utilities
2.5.1 Install electrical wiring and equipment in accordance with the National Electrical Code (current NFPA
70).
2.5.2 Install electric lights located within the equipment enclosure of the system in jacketed globes.
2.5.3 Motors should be readily accessible for inspection, lubrication, and maintenance.
Outside air at point 1 (80°F, 80% RH) is cooled to point 2 (70°F, 100% RH). The air is further cooled to the cooling coil tempera-
ture at point 3 (50°F, 100% RH). The dewpoint of the outside air at point 1 is 70°F. If the air is not reheated (points 3 to 4), the
inside air will be saturated. Fogging will occur if the outside air is admitted to the saturated room when the inside temperature is
below 70°F.
2.6.2 Air should not be recirculated from any space in which noticeable quantities of flammable vapors or
combustible dust are given off. This does not consider industrial exhaust systems covered by other FM Global
data sheets.
2.6.3 The outside air intake should be screened and located to avoid drawing in combustible or other foreign
materials and to lessen the hazard from exposure fires.
2.6.4 Protect open motors having commutators or sliding contacts so that sparks from the motors cannot
reach adjacent combustible material.
back to occupied spaces to provide comfort to occupants or to provide a specific set of environmental con-
ditions established within the conditioned space. The air conditioning system provides the simultaneous
control of temperature, humidity, air motion, noise level, air cleanliness, and quality of ventilation.
In recent years, the characteristics of air-handling systems have changed. While separate steel duct sys-
tems have not been abandoned, many air-handling systems are using new methods to accomplish air
distribution. Air is moved through cells integral with the structural load-bearing elements of the floor slabs,
through ceiling voids, through shafts that act simultaneously as air ducts and enclosures for air ducts, and
through various other means. Discharges are made through light fixtures, slits, and perforations. Air may
be induced, recirculated, or exhausted. Steel ducts are frequently insulated externally or internally for ther-
mal, vapor, or sound control. There are also new materials. Aluminum and glass fiber boards are commonly
used for ducts, and frequent proposals are made for the use of plastics or paper-based ducts or channels.
Flexible connectors, used in great numbers, frequently employ various plastics. The use of plastic ducts
should be discouraged because they pose serious fire and smoke hazards.
One important function of many air conditioning systems is to control relative humidity. Primary and second-
ary cooling coils are often provided to cool the air as much as possible. The air is then reheated to a specified
temperature which lowers the relative humidity. Without reheat, room air could become saturated (100% rela-
tive humidity). This increases the chance that room air fogging (condensation of water vapor into moisture)
and condensation on surfaces will occur.
This exposes a large area of the property to smoke damage and hampers manual fire fighting. For this rea-
son, the system is sometimes shut down during fires. The ducts interconnecting various floors or areas may
still provide significant paths for smoke migration, even though the system is shut down.
These ducts and other components of the system provide a ready means of spreading fire, smoke, and toxic
gases throughout a building.
3.2.3.1 Plenums
A plenum is an air compartment or chamber in which one or more ducts are connected, and which forms
part of an air distribution system.
Plenums are generally constructed of galvanized steel or aluminum. However, the space above suspended
ceilings or below raised floors is frequently used as a supply, return, or exhaust plenum to reduce the amount
of sheet metal work. The plenum chamber is connected with the conditioned area by openings through either
the floor or ceiling. These spaces may be insulated and they are generally used to run electrical wiring and
other auxiliary services. When this occupancy poses a fire hazard, fire and smoke may spread to the
conditioned area. Therefore, proper precautions need to be taken to prevent this occurrence.
3.2.3.4 Filters
Noncombustible filters can collect combustible dust and lint during normal air conditioning operation. There-
fore, the combustibility and smoke generation of a filter after a period of service partly depends on the nature
and quantity of contaminants collected. Consequently, each case must be evaluated individually.
The most common types of filters used in modern air conditioning systems are panel filters (Fig. 12), dry-
type extended surface filters (bag type) (Fig. 13), automatic moving-curtain viscous or dry impingement filters
(Fig. 14), automatic self-cleaning viscous air filters (Fig. 15), and electronic air filters (Figs. 16, 17 & 18).
Fig. 13. Dry-type extended surface filters (bag type). (American Air Filter Co.)
Fig. 14. Moving-curtain viscous or dry impingement automatic roll filters. (American Air Filter Co.)
but a smoke detector should be used if it is important to sense cool smoke. Fire dampers or doors can be
arranged to have a dual function of stopping fire and/or smoke. To perform dual functions it is necessary
to provide a release mechanism that is both thermally responsive and sensitive to signals from smoke
detectors (Fig. 7).
The air-conditioning system can spread smoke rapidly, and is normally shut down in the event of fire. How-
ever, special operating modes, other than shutdown, may be devised in particular situations to help restrict
the spread of fire and smoke (Figs. 3 & 10). Such systems must be designed with a knowledge of the fire and
smoke situations that may occur, of the dominant mechanisms of smoke movement, delineation of smoke
control objectives, and building air leakage characteristics. (See Recommendation Nos. 2.4.6 through 2.4.6.7
under Section 2.4 ‘‘Operation and Maintenance’’.)
The sprinkler alarm may be interconnected with the smoke control system to activate this system in case
of failure of the smoke and heat detectors.
Fig. 15. Automatic self-cleaning viscous air filters. (American Air Filter Co.)
form of pockets or V-shaped pleats. In other designs, the medium may be self-supporting because of inher-
ent rigidity or because air flow inflates it into extended form (Fig. 13). When the filters are filled with dirt,
they are discarded and replaced with clean media.
Fig. 17. Electronic air filters with extended surface filter storage section. (American Air Filter Co.)
Fig. 18. Electronic air filters with automatic roll filter storage section. (American Air Filter Co.)
3.7.2 Electronic Air Filters with Extended Surface Filter Storage Section
The filter consists of a close-coupled agglomerator section and a storage section (Fig. 17). The agglom-
erator section contains the all-aluminum plates. The ionizer voltage is 12.0 KV and the plate voltage 5.8 KV.
All insulators are shielded from the dirty air stream.
The storage section consists of 2 by 2 ft (0.6 by 0.6 m), high-efficiency, dry-type replaceable cartridges. The
cartridge is made of fiberglass fibers, supported on the air-leaving side by flexible scrim. This prevents the
metal boxes from closing the grid. The replaceable cartridges are collapsible and do not require storage space
of more than 2 by 2 by 4 ft (0.6 by 0.6 by 1.2 m) per cartridge.
Minute dust particles are electronically attracted and adhere to each other on the dry plates of the agglom-
erator section. As the trapped dust particles build up (agglomerate) on the collector plates, the mass
increases until the accumulation is swept off the plates by the air stream. Dirt is then carried onto the media
in the storage section.
3.7.3 Electronic Air Filters with Automatic Roll Filter Storage Section
The unit consists of an agglomerator section and storage section combined into one integral filter (Fig. 18).
The electronic precipitation principle employed in the agglomerator section is a method of removing dust
and smoke from the air by electrical attraction. This is accomplished by imposing an electrostatic charge of
definite polarity on the dust particle through ionization, and collecting the charged particles on metal plates
of opposite polarity.
Minute dust particles are electrostatically attracted and adhere to each other on the dry plates of the agglom-
erator section. As the trapped dust particles build up on the collector plates, the mass increases until the
accumulation is swept off the plates by the air stream. This accumulation is then carried onto the bonded glass
fiber media of the storage section.
The glass fiber blanket is fed automatically in small increments down the face of the storage section from
a roll at the top. The used media and accumulated dirt are wound tightly into a compact roll at the bottom.
The used roll is discarded and replaced with a new one.
Though the filtering medium itself may be noncombustible, in some cases, combustible dust and lint may
accumulate in the filters during normal operations. This may cause substantial increase of the fire hazard in
the air conditioning system. Consequently, proper protection measures should be considered when warranted.
4.0 REFERENCES
4.1 FM Global
Data Sheet 1-22, Criteria for Maximum Foreseeable Loss Fire Walls and Space Separation.
Data Sheet 1-23, Protection of Openings in Fire Subdivisions.
Data Sheet 5-48, Automatic Fire Detectors.
Data Sheet 7-7/17-12, Semiconductor Fabrication Facilities.
Data Sheet 7-78, Industrial Exhaust Systems.