fmb920 User Manual v0 23 PDF
fmb920 User Manual v0 23 PDF
V0.23
Table of contents
1 INTRODUCTION ..................................................................................................................... 7
1.1 ATTENTION ............................................................................................................................ 7
1.2 INSTRUCTIONS OF SAFETY ......................................................................................................... 7
1.3 LEGAL NOTICE ........................................................................................................................ 8
1.4 ABOUT DOCUMENT ................................................................................................................. 8
2 BASIC DESCRIPTION ............................................................................................................... 8
2.1 BASIC CHARACTERISTICS ........................................................................................................... 9
2.2 TECHNICAL FEATURES............................................................................................................. 10
2.3 TECHNICAL INFORMATION ABOUT INTERNAL BATTERY................................................................... 11
2.4 ELECTRICAL CHARACTERISTICS .................................................................................................. 12
2.5 ABSOLUTE MAXIMUM RATINGS ............................................................................................... 12
3 CONNECTION, PINOUT, ACCESSORIES .................................................................................. 13
3.1 HOW TO INSERT SIM CARD INTO FMB920 DEVICE: .................................................................... 13
3.2 HOW TO ADD MICROSD CARD INTO FMB9XX DEVICE ................................................................. 13
3.3 INSTALLING FMB920 DRIVERS ................................................................................................ 14
3.4 ACCESSORIES........................................................................................................................ 16
3.5 TERMINAL LOG FOR FMB DEVICES............................................................................................ 18
3.6 NAVIGATE LED..................................................................................................................... 19
3.7 STATUS LED ........................................................................................................................ 19
4 OPERATIONAL BASICS .......................................................................................................... 20
4.1 OPERATIONAL PRINCIPALS....................................................................................................... 20
4.2 SLEEP MODES ....................................................................................................................... 20
4.2.1 Sleep mode ............................................................................................................. 20
4.2.2 Deep Sleep mode .................................................................................................... 20
4.3 VIRTUAL ODOMETER .............................................................................................................. 21
4.4 FEATURES ............................................................................................................................ 22
4.4.1 ECO driving/Green driving Scenarios ...................................................................... 22
4.4.2 Over Speeding Scenario. ......................................................................................... 22
4.4.3 Excessive Idling ....................................................................................................... 23
4.4.4 Jamming detection ................................................................................................. 23
4.4.5 Trip.......................................................................................................................... 23
4.4.6 DOUT Control Via Call ............................................................................................. 23
4.5 GPS FUEL CONSUMPTION ...................................................................................................... 23
4.6 SCENARIOS ACCELEROMETER................................................................................................... 23
4.6.1 Unplug Detection .................................................................................................... 23
4.6.2 Towing Detection.................................................................................................... 23
4.6.3 Crash Detection ...................................................................................................... 23
4.7 BLUETOOTH ......................................................................................................................... 23
5 CONFIGURATION ................................................................................................................. 24
5.1 CONFIGURATOR .................................................................................................................... 24
5.2 SYSTEM SETTINGS.................................................................................................................. 26
5.3 RECORDS SETTINGS................................................................................................................ 28
5.4 GSM SETTINGS, GPRS PART ................................................................................................... 28
5.5 GSM SETTINGS, SMS/CALL PART ............................................................................................ 29
5.6 GSM SETTINGS, OPERATOR LIST .............................................................................................. 31
5.7 DATA ACQUISITION MODE SETTINGS ........................................................................................ 31
5.8 FEATURES SETTINGS............................................................................................................... 35
5.8.1 Eco/Green Driving................................................................................................... 35
5.8.1.1 Data output......................................................................................................................... 36
5.8.1.2 Auto Calibaration ................................................................................................................ 36
5.8.2 Over Speeding......................................................................................................... 37
5.8.3 Excessive Idling ....................................................................................................... 37
5.8.4 Jamming ................................................................................................................. 37
5.8.5 DOUT control via call .............................................................................................. 37
5.8.6 Trip settings ............................................................................................................ 37
5.9 AUTOGEOFENCING SETTINGS .................................................................................................. 38
5.10 GPS FUEL COUNTER.............................................................................................................. 39
5.11 SCENARIOS ACCELEROMETER................................................................................................... 40
5.11.1 Unplug Detection .................................................................................................... 40
5.11.2 Towing Detection.................................................................................................... 41
5.11.3 Crash Detection ...................................................................................................... 41
5.12 BLUETOOTH ......................................................................................................................... 42
5.13 HOW TO CONNECT BLUETOOTH HANDS FREE ADAPTER TO FMB DEVICE .......................................... 45
5.13.1 Bluetooth settings configuration ............................................................................ 45
5.13.2 Connecting Bluetooth Hands Free adapter ............................................................ 47
5.14 DEVICE’S LOG USING YOUR MOBILE PHONE................................................................................. 47
5.15 DEVICE DEBUG OVER ANDROID SMARTPHONE............................................................................. 48
5.16 HOW TO CONNECT OBD II BLUETOOTH DONGLE TO FMB DEVICE.................................................. 50
5.16.1 Bluetooth settings configuration ............................................................................ 50
5.16.2 Connecting to Bluetooth OBD II dongle .................................................................. 52
5.16.3 Supported Bluetooth OBD II dongles ...................................................................... 52
5.17 SMS EVENTS........................................................................................................................ 53
5.18 I/O SETTINGS ....................................................................................................................... 55
6 SMS COMMAND LIST ........................................................................................................... 56
6.1 SMS COMMAND LIST............................................................................................................. 57
6.1.1 getinfo .................................................................................................................... 57
6.1.2 getver ..................................................................................................................... 58
6.1.3 getstatus ................................................................................................................. 58
6.1.4 getgps ..................................................................................................................... 59
6.1.5 ggps ........................................................................................................................ 59
6.1.6 readio # ................................................................................................................... 59
6.1.7 getparam ................................................................................................................ 59
6.1.8 setparam ................................................................................................................ 60
6.1.9 flush #,#,#,#,#,#,# ................................................................................................... 60
6.1.10 setdigout................................................................................................................. 60
6.1.11 countrecs ................................................................................................................ 60
6.1.12 towingreact ............................................................................................................ 60
6.1.13 btgetlist .................................................................................................................. 61
6.2 SYSTEM PARAMETERS ............................................................................................................ 61
6.2.1 Sleep Mode (ID=102) .............................................................................................. 61
6.2.2 Sleep timeout (ID=103) ........................................................................................... 61
6.2.3 Movement Source (ID=100) .................................................................................... 61
6.2.4 Static Navigation (ID=106) ..................................................................................... 62
6.2.5 Saving/Sending without time synchronization (ID=107) ........................................ 62
6.2.6 GNSS Source (ID=109) ............................................................................................. 62
6.2.7 Ignition settings (ID=101) ....................................................................................... 62
6.2.8 High voltage level (ID=104) .................................................................................... 62
6.2.9 Low voltage level (ID=105) ..................................................................................... 63
6.2.10 Led indication (ID=108) ........................................................................................... 63
6.2.11 Synchronization settings (ID=900) .......................................................................... 63
6.2.12 NTP Resync (ID=901)............................................................................................... 63
6.2.13 NTP server 1 (ID=902) ............................................................................................. 63
6.2.14 NTP server 2 (ID=903) ............................................................................................. 63
6.3 RECORDS PARAMETERS .......................................................................................................... 64
6.3.1 Sorting (ID=1002) ................................................................................................... 64
6.3.2 Open Link Timeout (ID=1000) ................................................................................. 64
6.3.3 Server Response Timeout (ID=1001) ....................................................................... 64
6.4 GSM PARAMETERS ............................................................................................................... 64
6.4.1 GPRS content activation (ID=2000) ....................................................................... 64
6.4.2 APN Name (ID=2001) ............................................................................................ 65
6.4.3 APN username (ID=2002) ..................................................................................... 65
6.4.4 APN Password (ID=2003) ...................................................................................... 65
6.4.5 Domain (ID=2004) .................................................................................................. 65
6.4.6 Target Server Port (ID=2005) .................................................................................. 65
6.4.7 Protocol (ID=2006) ................................................................................................ 66
6.5 SMS/CALL SETTINGS ............................................................................................................. 66
6.5.1 SMS data sending settings (ID=3000) ..................................................................... 66
6.5.2 Data send number (ID=3001) ................................................................................. 66
6.5.3 Authorized phone numbers (ID=4000-4009) .......................................................... 66
6.5.4 SMS Event Predefined Numbers (ID=6000-6009) ................................................... 66
6.5.5 SMS Login (ID=3003) .............................................................................................. 66
6.5.6 SMS Password (ID=3004) ........................................................................................ 67
6.5.7 Incoming call action (ID=3005) ............................................................................... 67
6.5.8 Outgoing Call Trigger (ID=3007) ............................................................................. 67
6.5.9 GSM number index (ID=3008) ................................................................................ 67
6.5.10 Operator List (ID=5000-5049) ................................................................................. 67
6.6 DATA ACQUISITION MODES PARAMETERS .................................................................................. 68
6.6.1 Home Network GSM operator code “Vehicle on STOP” parameters ...................... 68
6.6.1.1 Min Period (ID=10000)........................................................................................................ 68
6.6.1.2 Min Saved Records (ID=10004) ........................................................................................... 68
6.6.1.3 Send Period (ID=10005) ...................................................................................................... 68
6.6.2 Home Network GSM operator code “Vehicle MOVING” parameters ..................... 68
6.6.2.1 Min Period (ID=10050)........................................................................................................ 68
6.6.2.2 Min Distance (ID=10051) .................................................................................................... 68
6.6.2.3 Min Angle (ID=10052) ......................................................................................................... 69
6.6.2.4 Min Speed delta (ID=10053) ............................................................................................... 69
6.6.2.5 Min Saved Records (ID=10054) ........................................................................................... 69
6.6.2.6 Send Period (ID=10055) ...................................................................................................... 69
6.6.3 Roaming Network GSM operator code “Vehicle on STOP” parameters ................. 69
6.6.3.1 Min Period (ID=10100)........................................................................................................ 69
6.6.3.2 Min Saved Records (ID=10104) ........................................................................................... 70
6.6.3.3 Send Period (ID=10105) ...................................................................................................... 70
6.6.4 Roaming Network GSM operator code “Vehicle MOVING” parameters ................ 70
6.6.4.1 Min Period (ID=10150)........................................................................................................ 70
6.6.4.2 Min Distance (ID=10151) .................................................................................................... 70
6.6.4.3 Min Angle (ID=10152) ......................................................................................................... 70
6.6.4.4 Min Speed (ID=10153) ........................................................................................................ 71
6.6.4.5 Min Saved Records (ID=10154) ........................................................................................... 71
6.6.4.6 Send Period (ID=10155) ...................................................................................................... 71
6.6.5 Unknown Network GSM operator code “Vehicle on STOP” parameters ................ 71
6.6.5.1 Min Period (ID=10200)........................................................................................................ 71
6.6.5.2 Min Saved Records (ID=10204) ........................................................................................... 71
6.6.5.3 Send Period (ID=10205) ...................................................................................................... 71
6.6.6 Unknown Network GSM operator code “Vehicle MOVING” parameters ............... 72
6.6.6.1 Min Period (ID=10250)........................................................................................................ 72
6.6.6.2 Min Distance (ID=10251) .................................................................................................... 72
6.6.6.3 Min Angle (ID=10252) ......................................................................................................... 72
6.6.6.4 Min Speed (ID=10253) ........................................................................................................ 72
6.6.6.5 Min Saved Records (ID=10254) ........................................................................................... 72
6.6.6.6 Send Period (ID=10255) ...................................................................................................... 73
6.7 FEATURES PARAMETERS ......................................................................................................... 73
6.7.1 Green driving priority (ID=11000) ........................................................................... 73
6.7.2 Max Acceleration Force (ID=11004) ....................................................................... 73
6.7.3 Max Braking Force (ID=11005) ............................................................................... 73
6.7.4 Max Cornering (ID=11006) ..................................................................................... 73
6.7.5 Green/Eco driving (ID=11007) ................................................................................ 73
6.7.6 Green driving digital output control settings (ID=11003) ....................................... 74
6.7.7 Green driving Digital output on duration (ID=11001) ............................................ 74
6.7.8 Green driving Digital output off duration (ID=11002) ............................................ 74
6.7.9 Overspeeding priority (ID=11100) .......................................................................... 74
6.7.10 Max allowed Speed (ID=11104) .............................................................................. 74
6.7.11 Overspeeding output control (ID=11103) ............................................................... 74
6.7.12 Overspeeding Digital output on duration (ID=11101) ............................................ 75
6.7.13 Overspeeding Digital output off duration (ID=11102) ............................................ 75
6.7.14 Excessive idling priority (ID=11200) ........................................................................ 75
6.7.15 Eventual records (ID=11203) .................................................................................. 75
6.7.16 Excessive idling minimum stop duration (ID=11205) .............................................. 75
6.7.17 Excessive idling minimum move duration (ID=11206) ............................................ 75
6.7.18 Excessive idling output control (ID=11204) ............................................................ 75
6.7.19 Excessive idling output on duration (ID=11201) ..................................................... 76
6.7.20 Excessive idling output off duration (ID=11202)..................................................... 76
6.7.21 Send sms to (ID=7064) ............................................................................................ 76
6.7.22 SMS Text (ID=8064) ................................................................................................ 76
6.7.23 Jamming (ID=11300) .............................................................................................. 76
6.7.24 Jamming Eventual records (ID=11303) ................................................................... 76
6.7.25 Jamming Output Control (ID=11304) ..................................................................... 77
6.7.26 Jamming DOUT on duration [ms] (ID=11301) ........................................................ 77
6.7.27 Jamming DOUT off duration [ms] (ID=11302) ........................................................ 77
6.7.28 DOUT control via call (ID=12000) ........................................................................... 77
6.7.29 DOUT deactivation settings (ID=12001) ................................................................. 77
6.7.30 DOUT duration timeout [s] (ID=12002) .................................................................. 77
6.7.31 Trip priority priority (ID=11800) ............................................................................. 78
6.7.32 Start Speed (ID=11803) ........................................................................................... 78
6.7.33 Ignition Off Timeout (ID=11804) ............................................................................. 78
6.7.34 Trip mode (ID=11802) ............................................................................................. 78
6.8 AUTOGEOFENCING................................................................................................................ 78
6.8.1.1 AutoGeofencing priority (ID=20000) ................................................................................. 78
6.8.1.2 Eventual Records (ID=20002)............................................................................................. 79
6.8.1.3 Activation Timeout (ID=20003) ......................................................................................... 79
6.8.1.4 Deactivate by (ID=20005) .................................................................................................. 79
6.8.1.5 AutoGeofence event generating (ID=20001) .................................................................... 79
6.8.1.6 Radius (ID=20004) .............................................................................................................. 79
6.8.1.7 Send sms to (ID=7061) ....................................................................................................... 79
6.8.1.8 SMS Text (ID=8061) ............................................................................................................ 80
6.9 GPS FUEL COUNTER .............................................................................................................. 80
6.9.1.1 City Consumption L/100km (ID=11900) ............................................................................ 80
6.9.1.2 Highway Consumption L/100km (ID=11901).................................................................... 80
6.9.1.3 Average Consumption L/100km (ID=11902) .................................................................... 80
6.9.1.4 City Speed [km/h] (ID=11903) ........................................................................................... 80
6.9.1.5 Highway Speed [km/h] (ID=11904) ................................................................................... 80
6.9.1.6 Average Speed [km/h] (ID=11905) .................................................................................... 80
6.9.1.7 Correction coefficient (ID=11906) ..................................................................................... 81
6.9.1.8 Fuel Consumption on Idling [L/h] (ID=11907) ................................................................... 81
6.9.1.9 Higher Speeds Add [%] (ID=11908).................................................................................... 81
6.9.1.10 Highway Consumption every km/h (ID=11909) .............................................................. 81
6.10 SCENARIOS ACCELEROMETER................................................................................................... 81
6.10.1 Unplug Detection .................................................................................................... 81
6.10.1.1 Scenario settings (ID=11500) ............................................................................................ 81
6.10.1.2 Eventual records (ID=11501) ............................................................................................ 81
6.10.1.3 Unplug detection mode (ID=11502) ................................................................................. 81
6.10.1.4 Send sms to (ID=7067) ...................................................................................................... 82
6.10.1.5 SMS Text (ID=8067) .......................................................................................................... 82
6.10.2 Towing Detection.................................................................................................... 82
6.10.2.1 Scenario setting (ID=11600).............................................................................................. 82
6.10.2.2 Eventual Records (ID=11601) ........................................................................................... 82
6.10.2.3 Activation Timeout (min) (ID=11602) ............................................................................... 82
6.10.2.4 Event Timeout (s) (ID=11603) ........................................................................................... 82
6.10.2.5 Make Call(Sms Event Number ID) (ID=11604) .................................................................. 83
6.10.2.6 Treshold (mg) (ID=11605) ................................................................................................. 83
6.10.2.7 Angle (deg) (ID=11606) ..................................................................................................... 83
6.10.2.8 Duration (msec) (ID=11607) ............................................................................................. 83
6.10.2.9 Send SMS (ID=7066) ......................................................................................................... 83
6.10.2.10 SMS Text (ID=8066) ........................................................................................................ 83
6.10.3 Crash Detection ...................................................................................................... 83
6.10.3.1 Scenario settings (ID=11400) ............................................................................................ 83
6.10.3.2 Duration [ms] (ID=11401) ................................................................................................. 84
6.10.3.3 Treshold [mG] (ID=11402) ................................................................................................ 84
6.10.3.4 Crash trace (ID=11406) ..................................................................................................... 84
6.10.3.5 Send sms to (ID=7068) ...................................................................................................... 84
6.10.3.6 SMS Text (ID=8068) .......................................................................................................... 84
6.11 BLUETOOTH ......................................................................................................................... 84
6.11.1.1 BT Radio (ID=800) ............................................................................................................. 84
6.11.1.2 Local name (ID 801) .......................................................................................................... 84
6.11.1.3 Local PIN (ID=802)............................................................................................................. 84
6.11.1.4 Security mode (ID=803) .................................................................................................... 85
6.11.1.5 External MAC (ID=804) ..................................................................................................... 85
6.11.1.6 External name (ID=805) .................................................................................................... 85
6.11.1.7 External PIN (ID=806) ........................................................................................................ 85
6.11.1.8 Connection mode (ID=807) ............................................................................................... 85
6.11.1.9 Authorized devices MAC list (ID=830 - 834) ..................................................................... 85
6.12 I/O PARAMETERS .................................................................................................................. 86
6.12.1 I/O#1 property parameter priority Ignition (ID=50000) ......................................... 86
6.12.2 I/O#1 priority (ID=50001) ....................................................................................... 86
6.12.3 I/O#1 High level (ID=50002) ................................................................................... 86
6.12.4 I/O#1 Low level (ID=50003) .................................................................................... 86
6.12.5 I/O#1 Event only (ID=50004) .................................................................................. 87
6.12.6 I/O#1 averaging length (ID=50005) ........................................................................ 87
6.13 I\O ELEMENTS PARAMETERS AND TYPES. ................................................................................... 87
7 MOUNTING RECOMMENDATIONS ....................................................................................... 92
7.1 CONNECTING WIRES.............................................................................................................. 92
7.2 CONNECTING POWER SOURCE ................................................................................................. 92
7.3 CONNECTING IGNITION WIRE .................................................................................................. 93
7.4 CONNECTING GROUND WIRE .................................................................................................. 93
8 FMB920 INSTALLATION INSTRUCTION ................................................................................. 94
9 CHANGE LOG ....................................................................................................................... 95
1 INTRODUCTION
1.1 Attention
Do not disassemble the device. If the device is
damaged, the power supply cables are not isolated or
the isolation is damaged, before unplugging the power
supply, do not touch the device.
All wireless data transferring devices produce
interference that may affect other devices which are
placed nearby.
7
1.3 Legal Notice
Copyright © 2016 Teltonika. All rights reserved. Reproduction, transfer, distribution or
storage of part or all of the contents in this document in any form without the prior written
permission of Teltonika is prohibited.
Other products and company names mentioned here may be trademarks or trade names
of their respective owners.
The manufacturer reserves the right to make changes and/or improvements at any time in
design, functionality, parameters and electrical characteristics without any prior notice and
without incurring obligations.
2 BASIC DESCRIPTION
FMB920 is tracking terminal with GNSS and GSM connectivity, which is able to collect
device coordinates and transfer them via GSM network to server. This device is perfectly suitable
for applications, which need location acquirement of remote objects.
Package contents1
The FMB920 device is supplied to the customer in a cardboard box containing all the
equipment that is necessary for operation. The package contains:
Already implemented FMB920 device into case;
Top and bottom device cover parts;
Input and output power supply cable with a 1x5 connection pins, which is already installed
into device.
1
Package content depends on Order Code, and can be customized by customer needs.
8
2.1 Basic characteristics
GSM / GPRS / GNSS features:
Teltonika TM2500 quad band module (GSM 850 / 900 / 1800 / 1900 MHz);
GPRS class 12;
SMS (text, data).
Integrated GNSS receiver
Up to -162 dBm GNSS receiver sensitivity.
Hardware features:
Built-in movement sensor;
Built-in Bluetooth 3.0;
Internal High Gain GNSS antenna;
Internal High Gain GSM antenna;
microSD card reader (up to 32Gb, FAT32);
170 mAh Li-ion rechargeable 3.7 V battery.
Interface features:
Power supply: 10 ÷ 30V;
1 digital input;
1 analog input;
1 open collector digital output (connecting external relays, LED, buzzers etc.);
2 LEDs indicating device status.
Special features:
Fast position fix;
High Quality track even in high density urban canyon;
Ultra small case;
Ready for harsh environment;
Color ribbon non-detachable cable;
Easy to mount in limited access areas;
Firmly fasten;
High gain internal GNSS and GSM antennas;
2 LED status indication;
Real-Time tracking;
Smart data acquisition based on:
o Time;
o Angle;
o Distance;
o Ignition or any other I/O event;
Sending acquired data via GPRS;
GPRS and SMS I/O events;
Virtual odometer;
Jamming detection
Configurable using Secured SMS Commands;
Overvoltage protection.
9
Table 1 FMB920 Supply voltage
Description Voltage Duration
Normal operation 10-30V Unlimited
Protection turns on, device turns off 34V Unlimited
Maximum voltage <70V Unlimited
Maximum voltage impulse 90V 5 milliseconds
2 1
Energy consumption has been tested at 12V voltage with no battery charging.
2
When in Deep Sleep mode no data storing and sending is activated.
10
Figure 1 FMB920 view & dimensions (tolerance ±2mm)
11
2.4 Electrical characteristics
VALUE
Min. Typ. Max. Unit
CHARACTERISTIC DESCRIPTION
Supply Voltage:
Supply Voltage (Recommended Operating Conditions) 10 30 V
Digital Output (Open Drain grade):
Drain current (Digital Output OFF) 120 μA
Drain current (Digital Output ON,
3,3 mA
Recommended Operating Conditions)
Static Drain-Source resistance (Digital
300 mΩ
Output ON)
Digital Input:
Input resistance (DIN1) 47 kΩ
Input Voltage (Recommended Operating Supply
0 V
Conditions) voltage
Input Voltage threshold (DIN1) 2,5 V
Analog Input:
Input Voltage (Recommended Operating
0 30 V
Conditions)
Input resistance 150 kΩ
Measurement error on 12V 0,9 %
Additional error on 12 V 108 mV
Measurement error on 30 V 0,33 %
Additional error on 30 V 88 mV
12
CAUTION: Digital Output (DOUT) is turned ON during every FMB9 device startup
for few seconds, i.e. in case of firmware update, restart with SMS command or
restart by disconnecting power from device. DO NOT connect any sensitive
equipment to DOUT, which could harm driver. For example fuel pump disabled
during driving, even for few second could be fatal for driver.
Note: SIM card insertion/removal must be performed when FMB device is
powered off – external voltage and battery disconnected. Otherwise SIM card
might be damaged or FMB device will not detect it.
13
③Correctly ④ Close microSD
insert microSD card card locker
into slot
`
Drivers:
Please download COM Port drivers from Teltonika website:
http://avl1.teltonika.lt/downloads/FMB9XY/MS_USB_ComPort_Driver_exe_v1.1032.3.zip
Installing drivers:
Extract and run FP_INBOX_InstallDriver_v1.1032.3.exe. This driver is used to detect FMB920
device connected to the computer. Click 'Next' in driver installation window (figures below):
14
Figure 2 Driver installation window
This will launch device driver installation wizard. In the following window click ‘Install’
button:
Setup will continue installing drivers and will display a window about successful process at
the end. Click 'Finish' to complete setup:
15
Figure 4 Driver installation window
3.4 Accessories
Note: Accessories are not included in device package, please order them
separately.
16
Figure 5 Panic button connection
In cases when sensor output signal is negative, an additional relay has to be installed to
convert negative signal to positive.
Immobilizer relay
When connected as shown below, FMB920 disables engine starter when output is ON.
More details about relays can be found below.
17
Relays
An ordinary automotive relay is used to invert input signal or to immobilize engine starter.
Note, that they are available as 12 V or 24 V.
18
3.6 Navigate LED
Behavior Meaning
Permanently switched on GNSS signal is not received
Blinking every second Normal mode, GNSS is working
Off GNSS is turned off because:
Deep sleep mode
Or
GNSS antenna short circuited
19
4 OPERATIONAL BASICS
4.1 Operational principals
FMB920 module is designed to acquire records and send them to the server. Records
contain GNSS data and I/O information. Module uses GNSS receiver to acquire GNSS data and is
powered with three data acquiring methods: time-based, distance-based and angle-based. Note,
that if FMB920 loses connection to GNSS satellites, it continues to make records, however
coordinate in these records remains the same (last known coordinate). All data is stored in flash
memory and later can be sent via GPRS.
GPRS and SMS settings are described in later sections. FMB920 communicates with server
using special data protocol.
FMB920 can be managed by SMS commands. SMS Command list is described in SMS
COMMAND LIST section. Module configuration can be performed only via SMS.
FMB920 can enter sleep mode if ALL of these conditions are met:
FMB920 has to be configured to work in Sleep mode and start sleep timeout is
reached;
Device must have synchronized time with GNSS satellites;
No movement by movement sensor is detected;
Ignition (configured Ignition Source) is off.
FMB920 exits sleep mode when if ONE of following conditions are true:
Movement by movement sensor is detected;
Ignition (configured Ignition Source) is turned on.
20
Movement by accelerometer is not detected;
Ignition (Configured to be detected by Power Voltage, Ignition or
Accelerometer) is off;
Min. Record Saving Period (Data Acquisition Mode settings) must be
bigger than Active Data Link Timeout parameter, that FMB920 could close GPRS
link.
Send period (Data Acquisition Mode settings) minus Active Data Link
Timeout must be more than 90 sec., that FMB920 could close GPRS link for at least
90 sec.
Sleep timeout is reached.
FMB920 exits deep sleep mode when if ONE of following conditions are true:
Movement by accelerometer is detected;
Ignition (Configured to be detected by Power Voltage, Ignition or Accelerometer) is
turned on.
Figure 9 Odometer continuous and Not continuous distance counting parameter example
21
4.4 Features
Using available features can greatly increase FMB920 usability options.
ECO driving or Green driving Scenario? Eco driving is based on accelerometer value and
Green driving based on GPS position.
Helps to prevent from exceeding fixed speed and inspects driver if needed. DOUT1 is
controlled by scenario for user needs, to manage buzzer, LED, etc.
22
4.4.3 Excessive Idling
Informs you if your vehicle is stationary but engine is on for selected period of time
to help you to save fuel
4.4.5 Trip
Trip customizable feature enables user extended monitoring of performed trips (from
engine start at present location to engine stop at arrived location), log their start and stop points,
view driven total distance3. Event will be generated (included into send records) only when trip
starts and finishes.
Note: Scenarios and Trip feature are activated (DOUTs are activated) only if
DIN1=1 (ignition is on).
4.7 Bluetooth
Bluetooth can work in two modes - slave or master.
3
Continuous odometer – total driven distance, works only in TRIP mode. Continues distance is
counted only for ONE trip. If trip is finnished (stop point is detected), odometer resets to 0 (zero). Next trip will start
counting from the begining.
23
While working as master mode - Bluetooth can connect to defined "hand free" or "OBDII"
system.
While working as slave mode - Bluetooth can accept incoming connection from external
device.
FMBXX supports one connection at a time.
5 CONFIGURATION
5.1 Configurator
New FMB920 module has default factory settings. Settings should be changed according to
your application and your GSM operator information.
FMB920 configuration may be performed via SMS commands or configurator.
FMB920 has one user editable profile.
It can be configured to acquire and send data to server. If device is not able to send data to
server, GSM is not available FMB920 will start storing records to flash memory. It is possible to
store up to 122880 data records with 64mb SD memory card. It will send data later when GPRS is
available again. Note that FMB920 can have memory full of records. In such case it will start
deleting oldest records in order to save new ones. Sending all data records to server may take
some time.
FMB920 configuration is performed via FMB920 Configurator program. Contact sales
manager to get the latest FMB920 Configurator version. FMB920 configurator operates on
Microsoft Windows OS and uses MS .NET Framework. For Windows XP you will need MS .NET
Framework 4 (with MS .NET Framework 4 update KB2468871-v2) for Windows Vista, Windows 7,
Windows 8.1, Windows 10 MS .NET Framework 4.6.2 or later. Please ensure that suitable MS
.NET Framework version for your OS is installed on your PC before starting configurator. Latest
MS .Net Framework version can be downloaded from official Microsoft web page.
Module configuration is performed over USB cable. Configuration process starts from
starting FMB920 Configurator program and then connecting to FMB920 device via Connect
button located in Online menu part. FMB920 has one user editable profile, which can be loaded
from device, and saved. User can also revert to default settings, by pressing Reset to defaults
button. After any modification of configuration settings it has to be saved to FMB920 device,
otherwise it will not be written to device.
24
Figure 10 Show home screen of connected device
25
5.2 System settings
System settings 9 configurable parameters:
Sleep settings, where user can choose sleep mode;
Ignition source, where user can choose between power voltage, digital input 1 and
accelerometer ignition sources
Object Motion Detection Settings, where user can configure 3 ways how FMB920
will detect stopped movement, and change its working mode (for working modes,
read section 5.7);
Static navigation settings, where user can turn static navigation on or off;
Records Settings, where user can enable or disable records when GPS is not
available (no time synchronization);
GNSS source Settings, where user can choose satellite system.
LED indication, where user can turn on or off indication leds.
Static Navigation Mode is a filter, which filters out track jumps when the object is
stationary. If Static navigation filter is disabled, it will apply no changes on GPS data. If Static
navigation filter is enabled, it will filter changes in GPS position if no movement is detected
(depends on Object Motion Detection Settings). It allows filtering GPS jumps when object is
parked (is not moving) and GPS position is still traced.
26
Figure 11 System settings configuration
In GNSS source Settings user can configure which GNSS system or systems to use.
User has choice to use only one system of GPS, Glonass, Galileo or Beidou. Also it is able
to chose two or three systems together. One exception is that you can not combine Beidou and
Glonass systems together.
27
5.3 Records settings
Here user can modify if FMB920 device will send newest records first, meaning, that the
most important thing is to know recent position of car, older records are being sent right after
newest records arrive to AVL application.
Activate Data Link Timeout is used to set timeout of link between FMB920 and AVL
application termination. If FMB920 has already sent all records it waits for new records before
closing link. If new records are generated in the period of this timeout, and minimum count to
send is reached, they are sent to AVL application. This option is useful when GSM operator
charge for link activation.
Server Response Timeout is used to set time period waiting for response from server side.
28
‘internet’ with CHAP authentication, it should be entered as ‘chap:internet’. Information
about APN and authentication type should be provided by your GSM operator.
29
Figure 14 SMS configuration
Outgoing Call Trigger parameter determines which event will triggers call. FMBXX supports
four different call triggers:
None selected – disables call trigger functionality.
DIN1 – first digital input event triggers call to user selected GSM number.
Crash Event – crash event triggers call to user selected GSM number.
DIN1 and Crash Event – both events triggers call to user selected GSM number.
SMS Event Time Zones
FMB9XX works with synchronized GPS time which is UTC+0, with this option customer can
configurate his time zone and get SMS with correct time.
30
Note: Please do not set Data Send Number to some cell phone number,
becaues it will not understand binary SMS. When sending a binary SMS to a
phone number, which is a server phone number, the server can interpret and
understand binary code, so the data can be read and you can view it on the
server.
SMS login and password and authorized number list are used to protect
FMB920 module from unauthorized access. Module accepts messages only
from a list of authorized numbers and with proper module login and password.
Numbers must be without “+” or “00” prefix. If no authorized numbers are
entered, module accepts messages from all numbers.
If operator list is left empty, it will allow using GPRS to any GSM operator. Please note that
FMB920 will work in Unknown mode only (make sure it is configured to allow data sending –
GPRS context is enabled).
31
By configuration user defines how records will be saved and sent. There are three different
modes: Home, Roaming and Unknown. All these modes with configured data acquisition and
send frequencies depend on current GSM Operator defined in Operator list (see section 5.6) and
are switched when GSM operator changes (e.g. vehicle passes through country boarder).
If current GSM operator is defined as Home Operator, device will work in Home Data
Acquisition mode, if current operator is defined as Roaming Operator, device will work in
Roaming Data Acquisition mode, and if current operator code is not written in Operator list (but
there is at least one operator code in the operator list), device will work in Unknown Acquisition
mode.
This functionality allows having different AVL records acquire and send parameters values
when object is moving or stands still. Vehicle moving or stop state is defined by Stop Detection
Source parameter. There are 3 ways for FMB920 to switch between Vehicle on Stop and Vehicle
Moving modes see section 5.7.
FMB920 has 6 different modes. Operational logic is shown in Figure 24.
If there are no operator codes entered into operator list, FMB920 will work in
Unknown network mode ONLY.
32
Operator search is performed every 15 minutes. Depending on current GSM operator,
Home, Roaming or Unknown mode can be changed faster than every 15 minutes. This process is
separate from operator search. Movement criteria are checked every second.
‘Min Saved Records’ defines minimum number of coordinates and I/O data that should be
transferred with one connection to server. If FMB920 does not have enough coordinates to send
to server, it will check again after time interval defined in ‘Sending Period’.
Send period – GPRS data sending to server period. Module makes attempts to send
collected data to server every defined period. If it does not have enough records (depends on
parameter Min. Saved Records described above), it tries again after defined time interval.
Note: Keep in mind that FMB920 operates in GMT:0 time zone, without
daylight saving.
FMB920 is able to collect records using four methods at the same time: time, distance,
angle and speed based data acquisition:
33
Min. time period
Distance based data acquiring (Min. distance) – records are being acquired when the distance
between previous coordinate and current position is greater than defined parameter value.
Entering zero disables data acquisition depending on distance.
Min. distance
Angle based data acquiring (Min. angle) – records are being acquired when angle difference
between last recorded coordinate and current position is greater than defined value. Entering
zero disables data acquisition depending on angle.
Min. angle
Speed based data acquiring (Min. Speed Delta) – records are being acquired when speed
difference between last recorded coordinate and current position is greater than defined value.
Entering zero disables data acquisition depending on speed.
34
5.8 Features settings
35
Table 27 ECO driving/Green driving parameters description
ECO driving/Green
driving configuration Description
parameter name
ECO driving/Green
Enable/Disable ECO driving/Green driving functionality
driving
Value which can be reached while accelerating without triggering harsh
Max Acceleration Force
acceleration event.
Value which can be reached while braking without triggering harsh
Max Braking Force
braking event.
Value which can be reached while cornering without triggering harsh
Max Cornering Force
cornering event.
*Example. If acceleration harsh event of 3.55 m/s2 detected. Record with value 3.55*10 = 35.5
≈ 36 will be saved ant sent to server.
36
5.8.2 Over Speeding
Scenario is activated and DOUT1 is ON, when vehicle speed exceeds parameter value.
Scenario is activated until current speed decreases below parameter value.
5.8.4 Jamming
Scenario is activated and DOUT1 IS ON, then jamming is detected.
37
stops. If later all Odometer values are summed up manually, the user gets the distance driven
during the whole period of the Trip.
38
parameters. It is possibility to state whether entering in or out of the geofence triggers an
asynchronous message.
AutoGeofencing option can be configured by following parameters visible in figure 28
below.
Activation TMO – Time period before Geofence is activated after vehicle stops.
Deactivate By:
Ignition – If ignition becomes high it will disable AutoGeofenze Zone;
Power Voltage – if power voltage enters entered value it will disable AutoGeofenze
Zone.
Digital input 1 – if digital input is triggered it will disable AutoGeofenze Zone.
Feature – Priority of generated event, which will be applied to saved record.
Enter Event – Event generation on Geofence entrance.
Exit Event – Event generation on Geofence exit.
On Both - Event generation on Geofence entrance Or exit
Eventual Records – Enable or Disable Eventual Records functionality.
Note that AutoGeofencing does not require entering coordinates, instead it requires GPS
visibility. If vehicle stopped and activation timeout has passed, an AutoGeofence will be created
around vehicle’s last position with set Radius value.
39
Configuration of Fuel Consumption
To configure this parameters use fuel consumption norm which are presented in your car
technical documentation. By default speeds for this fuel consumption norms are: City –
30 km/h, Average - 60km/h, Highway - 90 km/h. If you want, you can change it.
When speed are higher than highway fuel consumption speed, we add for highway fuel
consumption x % of highway fuel consumption every y km/h, by default FMB920 add
20% every 50 km/h. It means that fuel consumption is (1.2 * Highway Fuel Consumption)
on 140 km/h speed, (1.4 * Highway Fuel Consumption) on 190 km/h speed.
Correction coefficient is use for correction every value of fuel consumption which is send
to server (Used Fuel * Correction coefficient). By default it is 1, min 0.01 and max 2. For
example when correction coefficient is 1 and FMB920 calculate that used fuel of 35 m
distance is 20 ml, to server will be sent value: 20 ml, if correction coefficient is 1.2 to
server will be sent value: 20 * 1.2 = 24 ml.
Fuel consumption on idling used to calculate fuel consumption when ignition is on, but
vehicle speed is 0 km/h. By default it is 1 l/h, min 0 and max 5 l/h. Almost in all diesel
cars this parameter is less than 1.0 l/h. In gasoline cars this parameter is about 1.5 – 2.0
l/h.
40
Fig.5.11.1. Configuration window in configurator.
41
If trace is enabled FMB will collect acceleration data every 40 msec., аnd in the deep-sleep mode
too. Buffer is big enough to hold data for 5 seconds and on Crash Event detection, records will be
generated from this buffer, following these conditions:
Every second,
Acceleration changed more then > 50mG,
Data will be collected and records generated 5 seconds after the event using the same conditions.
Every generated record will have accelerometer X Y Z values included. Each record will have accurate
timestamps in milliseconds.
Usually between 20 to 30 records is generated on crash event detection.
5.12 Bluetooth
General functionality
42
Figure 24 Bluetooth general functionality
General functionality configures Bluetooth to work in slave mode. This mode allows any
external device to connect to FMBXX.
Parameter BT Radio allows user to select if he wants to enable or disable Bluetooth. There
is three different scenarios:
Disabled – Bluetooth functionality will be disabled.
Enable (hidden) – Bluetooth functionality will be enabled, but none of external
devices will be able to detect FMBXX but will be able to connect.
Enable (visible) – Bluetooth functionality will be enabled and any external device
will be able to detect and connect to FMBXX.
Local Name parameter lets user to declare visible name of FMBXX to external devices.
Local PIN parameter lets user to configure Bluetooth PIN of FMBXX device.
NOTE: FMBXX supports ONE connection at a time.
43
FMBXX Bluetooth has several different security modes:
PIN only – while external device trying to connect to FMBXX only Local PIN will
be recquired to complete connection.
PIN + MAC list – while external device trying to connect to FMBXX Local PIN
and Authorized Devices MAC List will be checked. If external device MAC ID is
in the list and correct Local PIN is entered then connection will be established,
else FMBXX will reject connection.
MAC list only – while external device trying to connect to FMBXX only
Authorized Devices MAC List will be checked. If external device MAC ID is in
the list then connection will be established, else FMBXX will reject connection.
None – while external device trying to connect to FMBXX neither Local PIN or Authorized
Device MAC list will be checked.
44
External Name parameter works as substring, this allows user to enter part of the full
external device name. For example, if external device name is "HandsFreeHeadset" and user
enters "HandsFree" in External Name parameter window then FMBXX will be allowed to connect
to external device named "HandsFreeHeadset".
3. After successful connection to device press “Load from device” button to load device
current configuration visible at Figure 2.1
45
Figure 2.1 Load configuration from device;
2.2 Bluetooth settings; 2.3 Enable Bluetooth; 2.4
Bluetooth local name; 2.5 Bluetooth security mode
2.6 Hands Free connection mode; 2.7
External Bluetooth device name; 2.8 Authorized
Devices MAC List; 2.9 Save device configuration
46
Figure 3. Incomming Call Action settings.
10. After all these steps press „Save to device“ to save configuration (Figure 2.9).
11. Now you can disconnect FMB device from a PC or stay connected if you want to make
further changes to configuration.
4
Hands Free device Bluetooth connection pairing instructions depends on specific model.
5
Hands Free device notification about paired Bluetooth connection depends on specific model.
47
5.15 Device debug over Android smartphone
1. Scan for visible BT devices using your Android smartphone
and connect to your FMB device.
4. Wait ~10 minutes and press “Save” button in menu. You will find saved log file in device
48
folder (My Files/BluetoothTerminal), select log files and press button Share via Email and
send them to the Teltonika support.
49
5.16 How to connect OBD II Bluetooth Dongle to FMB device
3. After successful connection to device press “Load from device” button to load device
current configuration visible at Figure 2.1
50
Figure 2.1 Load
configuration from device; 2.2
Bluetooth settings; 2.3 Enable
Bluetooth; 2.4 Bluetooth local
name; 2.5 Bluetooth security
mode 2.6 OBD II connection mode;
2.7 External OBD II Bluetooth
device name; 2.8 Authorized
Devices MAC List; 2.9 Save device
configuration
51
Figure 3. OBD II Bluetooth settings.
10. After all these steps press „Save to device“ to save configuration (Figure 2.9).
11. Now you can disconnect FMB device from a PC or stay connected if you want to make
further changes to configuration.
6
OBD II dongle Bluetooth connection pairing instructions depends on specific model.
52
Comparison of these chips is presented in Figure 4.
53
Figure 22 SMS Events PreDefined Numbers list
For example, if FMB920 is configured to send an SMS, when Ignition reaches High level,
with priority High and configured to generate event on both range enter and exit (figure 23),
then the sent SMS is:
54
Figure 23 Configured Ignition SMS event
The SMS Text field can be altered and any text can be entered. Maximum message length is
90 symbols (numbers, letters and symbols in ASCII, except for comma “,”).
ATTENTION!
If FMB920 is in Deep Sleep mode and SMS event occurs with LOW priority
(which does not wake up FMB920), then the device does not send the message.
It is saved in device memory until it wakes up from Deep Sleep mode and GSM
modem starts working normally. After it wakes up, all the messages that are
saved in memory will be sent, but keep in mind that only 10 messages can be
saved in memory – all other messages will not be saved, until there is room in
device memory.
55
(are always sent to server if enabled)
Nr. Property Name Description
1 Ignition Logic: 0 / 1
2 Movement Logic: 0 / 1
0 – home on stop, 1 – home on move, 2 –
3 Data mode roaming on stop, 3 – roaming on move, 4 –
unknown on stop, 5 – unknown on move
4 GSM signal GSM signal level value in scale 1 – 5
5 Deep sleep Logic: 0 / 1
States: 0 – short circ., 1 – connected.
Parameter defines if GPS antenna is short circuit.
6 GNSS power All the time value will be sent 1. The only
condition to get value 0, then antenna is damaged
and short circuit.
7 GNSS PDOP Probability * 10; 0-500
8 GNSS HDOP Probability * 10; 0-500
9 External Voltage Voltage: mV, 0 – 30 V
10 Speed Value in km/h, 0 – xxx km/h
11 GSM Cell ID GSM base station ID
Location Area code (LAC), it depends on GSM
operator. It provides unique number which
12 GSM Area Code
assigned to a set of base GSM stations. Max
value: 65536
13 Battery Voltage Shows battery Voltage in mV
14 Battery Current Shows battery Current in mA
15 Active GSM operator Currently used GSM Operator code
16 Trip odometer Distance between two records: m
17 Total odometer Total odometer count: m
18 Cell ID GSM base station ID
19 Digital Input 1 Logic: 0 / 1
20 Analog Input 1 Voltage: mV, 0 – 30 V
21 Digital output 1 Logic: 0 / 1
22 Fuel Used GPS Fuel used (ml) by GPS
23 Fuel Rate GPS Fuel Consumption by average speed (l/100km)
24 Axis X Accelerometer axis x value
25 Axis Y Accelerometer axis y value
26 Axis Z Accelerometer axis z value
56
6.1 SMS command list
Table 4 SMS commands
Command Description Response
getinfo Device runtime system information Yes
getver Returns code version, device IMEI, modem app Yes
version, RTC time
getstatus Returns Data Link:0 GPRS:0 Phone:0 SIM:0 OP:24602 Yes
Signal:5 NewSMS:0 Roaming:0 SMSFull:0 LAC:0 Cell ID:
0
getgps Returns GPS status, Satellite number, Latitude, Yes
Longitude, Altitude, Speed, Date, Time
ggps Returns location information with Google maps link Yes
readio Returns IO status Yes
cpureset Resets device No
getparam Returns selected parameter value Yes
setparam Sets selected parameter value Yes
flush Redirects device to other server Yes
countrecs Returns record number Yes
setdigout X Y Set digital output Yes
X – 0 or 1
(0 - OFF or 1 – ON)
Y – timeout value if needed (in seconds)
fc_reset Resets fuel consumption parameters Yes
towingreact Towing reactivation Yes
btgetlist Returns requested Bluetooth list(values:0, 1, 2) Yes
btgscan Starts Bluetooth scan(values: none, 1) Yes
btvisible Sets Bluetooth to visible with TMO Yes
btrelease Disconnects from current device and pauses auto connect Yes
functionality for TMO
btunpair Unpair Bluetooth device Yes
6.1.1 getinfo
57
PWR Start-up / restart reason
RST Restart Counter
GPS GPS receiver state. 0 – OFF, 1 – restarting, 2 – ON but no fix, 3 –
ON and operational, 4 – sleep mode
SAT Average satellites
TTFF Time to first fix
NOGPS No GPS Timer
SR Number of Sent Records
FG Failed GPRS counter
FL Failed link counter
SMS Sent SMS Counter
REC Records Found – number of records in the memory.
MD Data Mode state. 0 – Home and Stop, 1 – Home and Moving, 2 –
Roaming and Stop, 3 – Roaming and Moving, 4 – Unknown and
Stop, 5 – Unknown and Moving
Example: RTC:2017/5/23 12:49 Init:2017/5/23 11:18 UpTime:5446s PWR:PwrVoltage RST:0
GPS:1 SAT:0 TTFF:3939 NOGPS:1:24 SR:0 FG:229 FL:0 SMS:2 REC:15 MD:0
6.1.2 getver
Response details Description
App Ver Firmware version
Modem Ver Version of modem application
GPS Ver Version of GPS module
Hw Ver Version of hardware
Device IMEI IMEI
Example: App Ver:01.00.17 Rev:01 Modem Ver:TM25Q_D_01.00.00.00_010 GPS
Ver:AXN_3.82_3333_1Hw Ver:FMB9_MOD2_A0:B0:C1:D0 Device IMEI:352094080000950
6.1.3 getstatus
Response details Description
Data Link Indicate module connection to server at the moment: 0 – Not connected, 1
– connected
GPRS Indicate if GPRS is available at the moment
Phone Voice Call status: 0 – ready, 1 – unavailable, 2 – unknown, 3 –ringing, 4 –
call in progress, 5 – asleep
SIM SIM Status: 0-ready, 1-pin, 2-puk, 3-pin2, 4-puk2
OP Connected to GSM Operator: numerical id of operator
Signal GSM Signal Quality [0-5]
NewSMS Indicate if new message received
Roaming 0 – Home Network, 1 – roaming
SMSFull SMS storage is full? 0 – ok, 1 – SMS storage full
LAC GSM Tower Location Area Code
Cell ID GSM Tower Cell ID Code
58
Example: Data Link: 0 GPRS: 1 Phone: 0 SIM: 0 OP: 24602 Signal: 5 NewSMS: 0 Roaming: 0
SMSFull: 0 LAC: 1 Cell ID: 3055
6.1.4 getgps
Response details Description
GPS Indicates valid (1) or invalid (0) Gps data
Sat Count of currently available satellites
Lat Latitude (Last good Latitude)
Long Longitude (Last good Longitude)
Alt Altitude
Speed Ground speed, km/h
Dir Ground direction, degrees
Date Current date
Time Current GMT time
Example: GPS:1 Sat:0 Lat:54.666042 Long:25.225031 Alt:0 Speed:0 Dir:0 Date: 17/1/9 Time:
12:52:30
6.1.5 ggps
Response details Description
D Date
T Time
S Actual Speed
C Latitude (Last good Latitude), Longitude (Last good Longitude)
Url Google Maps Link
Example: D:17/1/9 T:12:52:30 S:0.00 C:54.666042, 25.225032 Url:
http://maps.google.com/?q=54.666042,25.225032&om=1speed:0
6.1.6 readio #
Response details Description
ID I/O element ID
Value I/O Element value
Example: Param ID:3 Value:0
6.1.7 getparam
Read parameter value. ID consists of 3 or 4 digits. A detailed list of parameters and
identifiers can be found in this chapter next later.
Example: ‚getparam 2001‘ command will request APN name
Answer: Param ID:2001 Value:wap
59
6.1.8 setparam
Read parameter value. ID consists of 3 or 4 digits. A detailed list of parameters and
identifiers can be found in this chapter next later.
Example: ‚setparam 2001:wap‘ will change configured APN name
Answer: Param ID:2001 Value:wap2
Example: ‘setparam 2001:wap;2002:user;2003:pass’ will change configured APN name, APN
username and APN password. SMS command of limited to 160 characters.
6.1.10 setdigout
Sets digital output to ON or OFF state (timeout for output is controllable)
Example: ‘setdigout 1 60’ will set OUT to high level for 60 seconds,
‘setdigout 1’ will set OUT to high level for infinite time.
6.1.11 countrecs
Returns the number of records save in the Micro SD card.
6.1.12 towingreact
Reactivates Towing Detection to initial state (does not wait for ignition to be OFF). Useful
60
when generated false Towing event and needs reactivation.
6.1.13 btgetlist
btgetlist command needs argument what list should be printed!
61
6.2.4 Static Navigation (ID=106)
When static navigation is enabled, FMB920 filters out GPS jumps, when it is not moving.
When it is disabled, it does not make any changes to collected GPS data.
Minimum Maximum Recommended Goes with (depends on) Value
value value value parameters type
0 1 1 U8
62
value value value parameters type
0 30000 30000 U8
63
6.3 Records parameters
ATTENTION! Some GSM operators may disconnect the device from an active
data link if the device doesn’t send any data for a very long time, even if active
data link timeout is set to maximum value. The amount of time that an operator
keeps the link open depends solely on the operator. For example, if active data
link timeout is set to maximum, 259200 seconds (72 hours), and the device
sends data to server every 86400 seconds (24 hours), the operator might
disconnect the link earlier and the device will have to connect to the server
anew. This may cost extra, depending on the operator GPRS data charge. It is
strongly recommended, when using active data link timeout, that data sending
to the server should not be very rare (24 hours or more). If data sending is more
frequent, then the operator will not disconnect the device form the server.
64
APN Password (ID=2003)
65
GPRS content activation
Empty 65535 - U16
(ID=2000)
6.5.5
SMS Login (ID=3003)
User login is used to ensure module security. Used in every SMS that is sent to device.
Example: ba321
66
Minimum Maximum Recommended Goes with (depends on) Value
value value value parameters type
Empty 5 char - SMS Password (ID=3004) S8[5]
67
6.6 Data Acquisition Modes parameters
68
6.6.2.3 Min Angle (ID=10052)
This parameter indicates angle in degrees in order to acquire new record. If angle
difference between last recorded coordinate and current position is greater than defined value,
new record is stored. This parameter is operational, when speed is higher than 10km/h. If value
is 0 it means no records by min angle will be saved.
Minimum Maximum Recommended Goes with (depends on) Value
value value value parameters type
Min Period (ID=10050)
0 180 - U16
Min Distance (ID=10051)
69
6.6.3.2 Min Saved Records (ID=10104)
This parameter defines minimum number of records in one data packet that can be sent to
server. It has higher priority than Data Send Period (ID=10105).
Minimum Maximum Recommended Goes with (depends on) Value
value value value parameters type
1 255 1 U8
70
6.6.4.4 Min Speed (ID=10153)
This parameter indicates speed difference in order to acquire new record. If speed
difference between last recorded coordinate and current position is greater than defined value,
new record is stored. If value is 0 it means no records by min distance will be saved.
Minimum Maximum Recommended Goes with (depends on) Value
value value value parameters type
Min Period (ID=10150)
0 255 10 Min Distance (ID=10151) U16
Min Angle (ID=10152)
71
(ID=10204)
72
6.6.6.6 Send Period (ID=10255)
This parameter indicates frequency (time interval in seconds) of sending data to server.
Minimum Maximum Recommended Goes with (depends on) Value
value value value parameters type
Min Saved Records
0 2592000 - U32
(ID=10254)
73
6.7.6 Green driving digital output control settings (ID=11003)
Sets digital output off (0) or on (1)
74
6.7.12 Overspeeding Digital output on duration (ID=11101)
Output ON duration in mili-seconds
Minimum Maximum Default value Goes with (depends on) Value
value value parameters type
21474836
0 200 U8
47
75
Minimum Maximum Recommended Goes with (depends on) Value
value value value parameters type
0 1 0 U16
76
Minimum Maximum Default value Goes with (depends on) Value
value value parameters type
0 1 1 U8
77
21474836
0 5 U8
47
6.8 AutoGeofencing
6.8.1.1 AutoGeofencing priority (ID=20000)
Defines priority of trip scenario:
0 – disabled, 1 – low, 2 – high, 3 – panic
Minimum Maximum Recommended Goes with (depends on) Value
value value value parameters type
0 3 0 U8
78
6.8.1.2 Eventual Records (ID=20002)
0 – disable, include parameter to all records, 1 – enable, include parameter to record only
if event was generated.
Minimum Maximum Recommended Goes with (depends on) Value
value value value parameters type
0 1 1 U8
79
6.8.1.8 SMS Text (ID=8061)
Configure uplug sms event text here.
Minimum Maximum default value Goes with (depends on) Value
value value parameters type
0 160 0 U64
80
6.9.1.7 Correction coefficient (ID=11906)
Sets the correction coefficient
Minimum Maximum Default value Goes with (depends on) Value
value value parameters type
0.01 2 1 Double
81
6.10.1.4 Send sms to (ID=7067)
Enable/disable sms event sending. 0 – Disable, 1-10 – sms will be sent to configured GSM
number. (SMS \ Call Settings -> GSM Predefined Numbers list.)
Minimum Maximum default value Goes with (depends on) Value
value value parameters type
0 10 0 U64
Note: „Unplug Detection“ work just in device with battery. FMB900 doesn‘t have this.
6.10.2 Towing Detection
6.10.2.1 Scenario setting (ID=11600)
0 – disabled, 1 – low, 2 – high, 3 – panic
Minimum Maximum default value Goes with (depends on) Value
value value parameters type
0 3 0 U64
82
6.10.2.5 Make Call(Sms Event Number ID) (ID=11604)
If function enabled makes call to specified phone number (configured in pre defined
numbers).
Minimum Maximum default value Goes with (depends on) Value
value value parameters type
0 - - U64
83
6.10.3.2 Duration [ms] (ID=11401)
Minimum Maximum default value Goes with (depends on) Value
value value parameters type
0 1000 5 U64
6.11 Bluetooth
6.11.1.1 BT Radio (ID=800)
Enables or disable Bluetooth feature. 0 – Disabled, 1 – Enable hidden, 2 – Enable visible
Minimum Maximum default value Goes with (depends on) Value
value value parameters type
0 2 0 U64
84
Minimum Maximum default value Goes with (depends on) Value
value value parameters type
0
4 Symbols 5555 String
Symbols
85
6.12 I/O parameters
I/O properties are additional data sources which are recorded along with usual GPS data.
86
Minimum Maximum Recommended Goes with (depends on) Value
value value value parameters type
I/O#1 property parameter priority
Ignition (ID=50000)
-
214748364 I/O#1 priority (ID=50001)
21474836 0 S32
7 I/O#1 High level (ID=50002)
47
I/O#1 Event only (ID=50004)
I/O#1 averaging length (ID=50005)
87
50003 Uint8 0 0 1 Ignition Low level
50004 Uint8 0 0 1 Ignition Event only
50005 Uint16 10 0 65535 Ignition Average
7000 Uint8 0 0 10 Send SMS
8000 String 0 0 160 SMS Text
50010 Uint8 1 0 3 Movement Priority
50011 Uint8 5 0 6 Movement Operand
50012 Uint8 0 0 1 Movement High level
50013 Uint8 0 0 1 Movement Low level
50014 Uint8 0 0 1 Movement Event only
50015 Uint16 1 0 65535 Movement Average
7001 Uint8 0 0 10 Send SMS
8001 String 0 0 160 SMS Text
50020 Uint8 1 0 3 Data Mode Priority
50021 Uint8 5 0 6 Data Mode Operand
50022 Uint8 0 0 5 Data Mode Hight level
50023 Uint8 0 0 5 Data Mode Low level
50024 Uint8 0 0 1 Data Mode Event only
7002 Uint8 0 0 10 Send SMS
8002 String 0 0 160 SMS Text
50030 Uint8 1 0 3 GSM Signal Priority
50031 Uint8 5 0 6 GSM Signal Operand
50032 Uint8 0 0 5 GSM Signal Hight level
50033 Uint8 0 0 5 GSM Signal Low level
50034 Uint8 0 0 1 GSM Signal Event only
50035 Uint16 1 0 65535 GSM Signal Average
7003 Uint8 0 0 10 Send SMS
8003 String 0 0 160 SMS Text
50040 Uint8 1 0 3 Deep Sleep Priority
50041 Uint8 3 0 6 Deep Sleep Operand
50042 Uint8 0 0 2 Deep Sleep Hight level
50043 Uint8 0 0 2 Deep Sleep Low level
50044 Uint8 0 0 1 Deep Sleep Event only
7004 Uint8 0 0 10 Send SMS
8004 String 0 0 160 SMS Text
50050 Uint8 1 0 3 GNSS Status Priority
50051 Uint8 5 0 6 GNSS Status Operand
50052 Uint8 0 0 1 GNSS Status Hight level
50053 Uint8 0 0 5 GNSS Status Low level
50053 Uint8 0 0 1 GNSS Status Event only
7005 Uint8 0 0 10 Send SMS
8005 String 0 0 160 SMS Text
50060 Uint8 0 0 3 GNSS PDOP Priority
50061 Uint8 3 0 6 GNSS PDOP Operand
50062 Uint16 0 0 1000 GNSS PDOP Hight level
50063 Uint16 0 0 1000 GNSS PDOP Low level
50064 Uint8 0 0 1 GNSS PDOP Event only
50065 Uint16 10 0 65535 GNSS PDOP Average
88
7006 Uint8 0 0 10 Send SMS
8006 String 0 0 160 SMS Text
50070 Uint8 1 0 3 GNSS HDOP Priority
50071 Uint8 3 0 6 GNSS HDOP Operand
50072 Uint16 0 0 1000 GNSS HDOP Hight level
50073 Uint16 0 0 1000 GNSS HDOP Low level
50074 Uint8 0 0 1 GNSS HDOP Event only
50075 Uint16 10 0 65535 GNSS HDOP Average
7007 Uint8 0 0 10 Send SMS
8007 String 0 0 160 SMS Text
50080 Uint8 1 0 3 External Voltage Priority
50081 Uint8 6 0 6 External Voltage
50082 Uint16 1000 0 60000 Operand
External Voltage Hight
50083 Uint16 0 0 60000 Externallevel
Voltage Low
50084 Uint8 0 0 1 level Event
External Voltage
50085 Uint16 10 0 65535 only Average
External Voltage
7008 Uint8 0 0 10 Send SMS
8008 String 0 0 160 SMS Text
50090 Uint8 1 0 3 Speed Priority
50091 Uint8 3 0 6 Speed Operand
50092 Uint16 0 0 300 Speed Hight level
50093 Uint16 0 0 300 Speed Low level
50094 Uint8 0 0 1 Speed Event only
50095 Uint16 1 0 65535 Speed Average
7009 Uint8 0 0 10 Send SMS
8009 String 0 0 160 SMS Text
50100 Uint8 0 0 3 GSM Cell ID Priority
50101 Uint8 3 0 6 GSM Cell ID Operand
50102 Uint32 0 0 999999 GSM Cell ID Hight level
50103 Uint32 0 0 999999 GSM Cell ID Low level
50104 Uint8 0 0 1 GSM Cell ID Event only
7010 Uint8 0 0 10 Send SMS
8010 String 0 0 160 SMS Text
50110 Uint8 0 0 3 GSM Area Code Priority
50111 Uint8 3 0 6 GSM Area Code Operand
50112 Uint32 0 0 999999 GSM Area Code Hight
50113 Uint32 0 0 999999 GSM Arealevel
Code Low
50114 Uint8 0 0 1 GSM Area level
Code Event
7011 Uint8 0 0 10 only
Send SMS
8011 String 0 0 160 SMS Text
50120 Uint8 1 0 3 Battery Voltage Priority
50121 Uint8 3 0 6 Battery Voltage Operand
50122 Uint16 0 0 5000 Battery Voltage Hight
50123 Uint16 0 0 5000 Battery level
Voltage Low
50124 Uint8 0 0 1 level Event
Battery Voltage
50125 Uint8 0 0 10 only Average
Battery Voltage
7012 Uint8 0 0 10 Send SMS
8012 String 0 0 160 SMS Text
89
50130 Uint8 1 0 3 Battery Current Priority
50131 Uint8 3 0 6 Battery Current Operand
50132 Uint16 0 0 5000 Battery Current Hight
50133 Uint16 0 0 5000 Battery level
Current Low
50134 Uint8 0 0 1 level
Battery Current Event
50135 Uint8 0 0 10 only Average
Battery Current
7013 Uint8 0 0 10 Send SMS
8013 String 0 0 160 SMS Text
50140 Uint8 0 0 3 Active GSM Operator
50141 Uint8 5 0 6 Priority
Active GSM Operator
50142 Uint32 0 0 999999 ActiveOperand
GSM Operator
50143 Uint32 0 0 999999 Active GSMlevel
Hight Operator
50144 Uint8 0 0 1 ActiveLowGSMlevel
Operator
7014 Uint8 0 0 10 Event only
Send SMS
8014 String 0 0 160 SMS Text
50150 Uint8 0 0 3 Trip Odometer Priority
50151 Uint8 3 0 6 Trip Odometer Operand
50152 Uint32 0 0 1000000 Trip Odometer Hight
50153 Uint32 0 0 1000000 level Low level
Trip Odometer
50154 Uint8 0 0 1 Trip Odometer Event
7015 Uint8 0 0 10 only
Send SMS
8015 String 0 0 160 SMS Text
50160 Uint8 0 0 3 Total Odometer Priority
50161 Uint8 3 0 6 Total Odometer
50162 Uint32 0 0 10000000 Operand Hight
Total Odometer
50163 Uint32 0 0 10000000 level
Total Odometer Low
50164 Uint8 0 0 1 level Event
Total Odometer
7016 Uint8 0 0 10 only
Send SMS
8016 String 0 0 160 SMS Text
50170 Uint8 0 0 3 Digital Input 1 Priority
50171 Uint8 0 0 6 Digital Input 1 Operand
50172 Uint8 0 0 1 Digital Input 1 Hight
50173 Uint8 0 0 1 level
Digital Input 1 Low level
50174 Uint8 0 0 1 Digital Input 1 Event only
50175 Uint16 1 0 65535 Digital Input 1 Average
7017 Uint8 0 0 10 Send SMS
8017 String 0 0 160 SMS Text
50180 Uint8 0 0 3 Analog Input 1 Priority
50181 Uint8 6 0 6 Analog Input 1 Operand
50182 Uint16 1000 0 30000 Analog Input 1 Hight
50183 Uint16 0 0 30000 Analog Inputlevel
1 Low level
50184 Uint8 0 0 1 Analog Input 1 Event
50185 Uint16 10 0 65535 only1 Average
Analog Input
7018 Uint8 0 0 10 Send SMS
8018 String 0 0 160 SMS Text
50190 Uint8 0 0 3 Digital Output 1 Priority
50191 Uint8 0 0 6 Digital Output 1
50192 Uint8 0 0 1 Digital Operand
Output 1 Hight
level
90
50193 Uint8 0 0 1 Digital Output 1 Low
50194 Uint8 0 0 1 level 1 Event
Digital Output
50195 Uint16 1 0 65535 only 1 Average
Digital Output
7019 Uint8 0 0 10 Send SMS
8019 String 0 0 160 SMS Text
50200 Uint8 0 0 3 Fuel Used GPS Priority
50201 Uint8 3 0 6 Fuel Used GPS Operand
50202 Uint32 0 0 1000000 Fuel Used GPS Hight
50203 Uint32 0 0 1000000 Fuel Usedlevel
GPS Low level
50204 Uint8 0 0 1 Fuel Used GPS Event
50205 Uint16 1 0 65535 Fuel UsedonlyGPS Average
7020 Uint8 0 0 10 Send SMS
8020 String 0 0 160 SMS Text
50210 Uint8 0 0 3 Fuel Rate GPS Priority
50211 Uint8 3 0 6 Fuel Rate GPS Operand
50212 Uint32 0 0 1000000 Fuel Rate GPS Hight level
50213 Uint32 0 0 1000000 Fuel Rate GPS Low level
50214 Uint8 0 0 1 Fuel Rate GPS Event only
50215 Uint16 1 0 65535 Fuel Rate GPS Average
7021 Uint8 0 0 10 Send SMS
8021 String 0 0 160 SMS Text
50220 Uint8 0 0 3 Axis X Priority
50221 Uint8 3 0 6 Axis X Operand
50222 Uint16 0 -8000 8000 Axis X Hight level
50223 Uint16 0 -8000 8000 Axis X Low level
50224 Uint8 0 0 1 Axis X Event only
50225 Uint16 1 0 65535 Axis X Average
7022 Uint8 0 0 10 Send SMS
8022 String 0 0 160 SMS Text
50230 Uint8 0 0 3 Axis Y Priority
50231 Uint8 3 0 6 Axis Y Operand
50232 Uint16 0 -8000 8000 Axis Y Hight level
50233 Uint16 0 -8000 8000 Axis Y Low level
50234 Uint8 0 0 1 Axis Y Event only
50235 Uint16 1 0 65535 Axis Y Average
7023 Uint8 0 0 10 Send SMS
8023 String 0 0 160 SMS Text
50240 Uint8 0 0 3 Axis Z Priority
50241 Uint8 3 0 6 Axis Z Operand
50242 Uint16 0 -8000 8000 Axis Z Hight level
50243 Uint16 0 -8000 8000 Axis Z Low level
50244 Uint8 0 0 1 Axis Z Event only
50245 Uint16 1 0 65535 Axis Z Average
7024 Uint8 0 0 10 Send SMS
8024 String 0 0 160 SMS Text
50250 Uint8 0 0 3 ICCID Priority
50251 Uint8 3 0 6 ICCID Operand
50252 Uint16 0 0 8000 ICCID Hight level
91
50253 Uint16 0 0 8000 ICCID Low level
50254 Uint8 0 0 1 ICCID Event only
7069 Uint8 0 0 10 Send SMS
8069 String 0 0 160 SMS Text
50260 Uint8 0 0 3 SD Status Priority
50261 Uint8 3 0 6 SD Status Operand
50262 Uint16 0 0 8000 SD Status Hight level
50263 Uint16 0 0 8000 SD Status Low level
50264 Uint8 0 0 1 SD Status Event only
7069 Uint8 0 0 10 Send SMS
8069 String 0 0 160 SMS Text
7 MOUNTING RECOMMENDATIONS
7.1 Connecting Wires
Wires should be fastened to the other wires or non-moving parts. Try to avoid heat
emitting and moving objects near the wires.
The connections should not be seen very clearly. If factory isolation was removed while
connecting wires, it should be applied again.
If the wires are placed in the exterior or in places where they can be damaged or exposed
to heat, humidity, dirt, etc., additional isolation should be applied.
Wires cannot be connected to the board computers or control units.
92
When module is connected, measure voltage again to make sure it did not decrease.
It is recommended to connect to the main power cable in the fuse box.
Use 3A, 125V external fuse.
93
8 FMB920 installation instruction
FMB920 is the device that has internal GNSS and GSM antenna.
Device should be mounted with the sticker view to the open sky (metal free). FMB920 area
with sticker and GNSS antenna is shown in figure 25.
Most light vehicles has oblique front window that opens most part of interior front panel.
FMB920 can be mounted under the plastic panel behind the front window, with the sticker
direction to a window (sky). It is recommended to place FMB920 behind dashboard as close to
the window as possible. A good example of GNSS antenna placement is displayed in a picture
below (area colored green).
94
9 CHANGE LOG
95
Added “Synchronization settings” parameters values.
Minor changes
22 2017-04-27 0.22 Correction “AutoGeofencing” parameters values.
Added SMS ID “Towing Detection”
Added Note: Firmware downgrade.
Added Note: Operand On Delta Change
Minor changes Battery description.
Correction “Green driving” parameters values.
23 2017-05-25 0.23
Correction “Green driving” description.
Added BT “Data Link” description.
Correction Value “GSM number index”
Correction “getinfo” SMS command description.
96