FG - ASCQ3109 - Welding and Quality Technician - Final - PKG - 01.08.2019 PDF
FG - ASCQ3109 - Welding and Quality Technician - Final - PKG - 01.08.2019 PDF
Sector
Automotive
Sub-Sector
Manufacturing
Welding
and Quality
Occupation
Welding Technician
Reference ID: ASC/Q3109, Version 1.0
NSQF Level: 3
Published by
ABC Company Ltd.
7,NSDC Marg.
New Delhi - 110002
Email:
Website:
Printed in India at
XYZ Company
New Delhi - 110016
Copyright © 2016
Automotive Skills Development Council
Sector Skill Council Contact Details:
Address: Sat Paul Mittal Building, 1/6, Siri Institutional Area,, Khel Gaon Road, New Delhi, Delhi
110049
Email: [email protected]
Phone: 011 4186 8090
Disclaimer
The information contained herein has been obtained from sources reliable to Automotive Skills Development
Council. Automotive Skills Development Council disclaims all warrantees to the accuracy, completeness or
adequacy of such information. Automotive Skills Development Council shall have no liability for errors,
omissions, or inadequacies, in the information contained herein, or for interpretations thereof. Every effort
has been made to trace the owners of the copyright material included in the book. The publishers would
be grateful for any omissions brought to their notice for acknowledgements in future editions of the book.
No entity in Automotive Skills Development Council shall be responsible for any loss whatsoever, sustained
by any person who relies on this material. The material in this publication is copyrighted. No parts of this
publication may be reproduced, stored or distributed in any form or by any means either on paper or
electronic media, unless authorized by the Automotive Skills Development Council.
iii
iv
Acknowledgements
The content of this guide is aligned to the curriculum of QP/NOS for Welding and Quality Technician.
For the development of this guide, Automotive Skills Development Council (ASDC) would like
to acknowledge the contributions made by Hero MotoCorp, JS Four Wheels, The Federation of
Automobile Dealers Associations (FADA) and Society of Indian Automobile Manufactures (SIAM).
We would also like to acknowledge the contributions of each and every stakeholder/ individual
who have contributed directly or indirectly to the ideas presented in this book.
v
Facilitator Guide
This book is designed for the facilitator help a candidate to acquire skills that are required for employment.
The content of this book is completely aligned to the National Occupation Standards QP/NOS and conform
to the National Skills Qualification Framework (NSQF).
• ASC/N3106 Remove the finished goods and store them in the designated place
• ASC/N0007 Conduct quality checks and inspection of the finished metal cast products
Key Learning Objectives for the specific NOS mark the beginning of the Unit/s for that NOS. The symbols
used in this book are described below.
Happy learning !!
Symbols Used
vi
Welding and Quality
Technician
Table of Contents
S.No. Modules and Units Page No.
1. Introduction 1
Unit 1.1 – Welding: An Introduction 3
Unit 1.2 – Basics of Measurement: An Introduction 15
2. Gas Metal Arc Welding (GMAW) – Before Welding (ASC/N3103) 27
Unit 2.1 – Why GMAW 29
Unit 2.2 – Parts of a GMAW Machine and Accessories 32
Unit 2.3 – Setting Up a GMAW Outfit 35
Unit 2.4 – Operating Parameters of GMAW 40
Unit 2.5 – Process Parameters of GMAW 43
Unit 2.6 – Applications of GMAW 46
3. Shielding Gas (ASC/N3103) 49
Unit 3.1 – Why Shielding Gas? 51
Unit 3.2 – Shielding Gas Selection 53
4. Safety (ASC/N0006, ASC/N0021) 55
Unit 4.1 – Hazards in Welding 57
Unit 4.2 – Personal Protective Equipment (PPE) 60
Unit 4.3 – Fire Safety 63
Unit 4.4 – First Aid for Electric Shock and Burns 72
Unit 4.5 – 5S 75
5. Welding Operation (ASC/N3104, ASC/N3105) 79
Unit 5.1 – Types of Weld – Fillet and Groove 81
Unit 5.2 – Types of Joints 84
Unit 5.3 – Welding Positions 86
Unit 5.4 – Material Preparation 94
Unit 5.5 – Edge Preparation 96
Unit 5.6 – Fit Up 99
Unit 5.7 – Welding Demonstration 101
Unit 5.8 – Welding Practice 121
6. Flux Cored Arc Welding (FCAW) (ASC/N3104) 163
Unit 6.1 – Principles of Flux Cored Arc Welding (FCAW) 165
vii
Facilitator Guide
viii
1. Introduction
Unit 1.1 – Welding: An Introduction
Unit 1.2 – Basics of Measurement: An Introduction
Facilitator Guide
2
Welding and Quality
Technician
Unit Objectives
At the end of this unit, Students will be able to:
1. State the different types of joining processes;
2. Describe the welding process;
3. Explain the importance of welding.
Resources to be Used
• Facilitator can use the available objects such as a marker, duster, pen, notebook etc.
Do
• Take a parcel, mention some details such as student name, hobbies, likes, dislikes etc.
• Make the students stand in a circle, close enough to the person each side of them that they can pass
the parcel quickly.
• Say ‘Stop’ when the students least expect it. The person who has the parcel at that time should get
out from the class.
• Those who get out should introduce themselves by providing the details mentioned in the parcel.
• The winner of the game should stand and introduce himself/herself at the end of the game.
• At last, say thanks to the students for their participation.
• Ask for feedback on the exercise of participation and what they derived out of it.
3
Facilitator Guide
Say
• What they understand by the word welding.
• Welding is a material joining process in which at least two sections are joined by optimum use of heat
as well as force.
• There are many types of joining processes:
Elaborate
Welding Process
4
Welding and Quality
Technician
Ask
• Ask them about their understanding for welding process.
• Ask about different joining processes
5
Facilitator Guide
Resources to be Used
• Facilitator can use the available objects such as a marker, duster, pen, notebook etc.
• PC with LCD Projector or Flip Chart
Do
• Greet and welcome the participants to the next session of the program.
Say
• It is an arc welding process where an electric arc is used to produce the heat required for the welding.
• The electric arc develops when electricity jumps across an air gap between the end of the metallic
electrode and the welding job surface. The metallic electrode is generally coated with the flux which
is consumable.
• The arc created due to the ionization of air between the electrode tip and the base metal generates
an intense arc heat having a temperature between3600C-4000 C.
• The welding current is provided by an AC or DC machine.
• The forceful heat of the arc melts a small portion (Molten pool) on the job directly under the arc and
towards the end of the electrode instantaneously.
• The flux coating on the electrode also melts and provides a gaseous shield around the arc which
secures the molten metal from atmospheric contamination. Hence this is called shielded metal arc
welding (SMAW).
• The welding speed and feed of the electrode is controlled manually by the welder himself. It is also
called manual metal arc welding (MMAW).
Ask
• Ask them about SMAW process
• Ask about difference between SMAW and MMAW process
6
Welding and Quality
Technician
7
Facilitator Guide
Do
• Greet and welcome the participants to the next session of the program.
Say
• GMAW is a wielding process in which there is a formation of an electric arc between a consumable
wire electrode and the work piece metal(s). This electric arc provides heat to the work piece metal(s),
leading them to melt and join.
• Gas metal arc welding (GMAW) is also known as metal inert gas (MIG) welding or metal active gas
(MAG) welding.
• The process can be semi-automatic or automatic.
• A constant voltage, direct current power source is generally used with GMAW; however, constant
current systems, as well as alternating current, can be used.
• There are four main methods of metal transfer in GMAW, such as globular, short-circuit, spray, and
pulsed-spray.
• At present, GMAW is the most preferred industrial welding process due to its speed and ability to
adapt the process of robotic automation. Unlike welding process that do not employ a shielding gas,
such as shielded metal arc welding, it is rarely used outdoors or in other areas of air volatility.
• Flux cored arc welding is an associated process that uses an electrode wire, which is hollow and filled
with flux, however, it avoids the use of a shielding gas.
Ask
• Ask them about GMAW process
• Ask about different methods of metal transfer in GMAW
8
Welding and Quality
Technician
9
Facilitator Guide
Resources to be Used
• Facilitator can use the available objects such as a marker, duster, pen, notebook etc.
• PC with LCD Projector or Flip Chart
Do
• Greet and welcome the participants to the next session of the program.
Say
• Like MMAW, GMAW, there are some other welding methods utilized in industry i.e. electric resistance
welding, spot welding and fusion welding.
• Electric Resistance Welding (ERW)
This welding process produce coalescence of faying surfaces where heat to form the weld is
generated by the electrical resistance of material combined with the time and the force used to hold
the materials together during welding. Some factors influencing heat or welding temperatures are
the proportions of the workpieces, the metal coating or the lack of coating, the electrode materials,
electrode geometry, electrode pressing force, electrical current and length of welding time.
These methods are efficient and cause little pollution, however, their applications are limited to
relatively thin materials and the equipment can be expensive
• Spot Welding
It is a resistance welding method and helpful to weld two or more overlapping metal sheet, studs,
projections, electrical wiring hangers, some heat exchanger fins and some tubing.
In this process, the output of the wielding power source restricts the thickness; as a result, the current
required for each application causes the variation in the equipment. Generally, the metal sheets are
held together by two copper electrodes and to transfer current through the sheets. The intense heat
is produced when the current is transferred from the electrodes to the sheets. As the heat is collected
in the work pieces between the copper electrodes because of the electrical resistance of the material,
the increasing temperature affects a rising resistance, and causes a molten pool contained most of
the time between the electrodes
• Seam Welding
This process generates a weld at the connecting surfaces of two like metals is known as seam welding.
The seam may be referred as a butt joint or an overlap joint and is usually a mechanized process.
However, seam welding varies from butt welding. Similar to spot welding, seam welding depends
10
Welding and Quality
Technician
on two electrodes, usually made from copper, to apply pressure and current. The electrodes are
disc shaped and rotate as the material passes between them. This allows the electrodes to stay in
constant contact with the material to make long continuous welds.
Ask
• Ask them about electric resistance welding
• Ask about seam and spot welding process
11
Facilitator Guide
Resources to be Used
• Available objects such as white Board, white board marker pens, duster.
• PC with LCD Projector or Flip Chart
• Participant Manual
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• GAS-TUNGSTEN ARC WELDING (GTAW), also known as HeliArc and tungsten inert gas (TIG). In the late
1930s, TIG welding process was created when necessity to weld magnesium became obvious.
• GTAW TIG Welding should be possible in any welding position and in manual, semiautomatic and
automatic modes.
• The melting temperature important to weld materials in manual, semiautomatic and (GTAW) process
is acquired by maintaining an arc between a tungsten alloy electrode and the workpiece.
• Weld pool temperatures can approach 25000C (45300F).
• An inert gas maintains the arc and shields the molten metal from atmospheric pollution. The inert gas
is ordinarily argon, helium, or mixture of helium and argon.
• The TIG Welding or GTAW process can be utilized to weld almost all metals and metal alloys i.e.
o Aluminium and aluminium alloys
o Copper and copper alloys
o Nickel and nickel alloys
o Magnesium and magnesium alloys
o Low alloy steel and carbon steels
o Volatile materials (for example, titanium and tantalum)
o Combining carbon and alloy steels
• To guard the welding area from atmospheric gases, for example, nitrogen and oxygen, which cause
12
Welding and Quality
Technician
deficiencies, shielding gases are essential in Gas Tungsten Arc Welding (GTAW).
• Electrodes for gas tungsten arc welding can be either pure tungsten alloys; they are typically shading
coded. The pure tungsten electrode is green in color. The alloyed tungsten electrodes can be brown,
yellow, red or blue depend upon the alloying elements.
• GTAW torches are available in various sizes, shapes, amperage and volumes. Gas Tungsten Arc Welding
(GTAW) torches gives a means for holding and changing the tungsten electrode that conducts the
current to the arc and carry shielding gas, electricity and cooling water.
• There are two main types of GTAW torches; the gas cooled welding torches used for welding thin
metals at currents under 200 amperes, and the water cooled torches used for welding medium and
thick metals
Elaborate
TIG Welding Principle
In the Gas Tungsten Arc Welding (GTAW) metal are intertwined by warming them by an electric arc built
up between a non-consumable (does not dissolve) tungsten electrode and the workpiece. A filler metal
may not be utilized relying upon the plan of the joint. The molten metal, tungsten electrode and welding
zone are protected from the climate (the air around it) by a surge of inert gas through the welding torch.
The subsequent welds have an identical chemical integrity as the first base metal.
Shielding gas
• joint design
Advantages of GTAW
13
Facilitator Guide
Limitations of GTAW
• Generates lesser deposition rates than consumable electrode arc welding methods.
• Needs a little more deftness and welder organization than gas metal arc welding (GMAW) or
shielded metal arc welding (SMAW) for manual welding
• Difficult in draughty surroundings due to trouble in shielding the weld zone correctly
• Adulteration of the weld metal, if appropriate shielding of the filler metal by the gas stream is not
kept
Ask
• Ask about working principle of GTAW.
• Ask about industrial applications of GTAW.
• Ask about components required for TIG welding.
• Ask about advantages and limitations of GTAW process.
14
Welding and Quality
Technician
Unit Objectives
At the end of this unit, students will be able to:
1. Identify and recognize basic measurement systems;
2. Differentiate between various measurement systems;
3. List the various measuring tools and its function;
4. Identify the required measuring instruments and tools for a task.
Resources to be Used
• Facilitator can use the available objects such as a marker, duster, pen, notebook, measuring
instruments etc.
• PC with LCD Projector or Flip Chart
Do
• Greet and welcome the participants to the next session of the program.
Ask
• You could ask the definition of Unit
• You could ask the body parts of a micrometer
• You could ask the different types of rules available
• You could ask the concept of vernier caliper
• You could ask the following concepts
15
Facilitator Guide
Say
• Measurement is the comparison of one quantity with standard quantity
• A unit of measurement is a definite magnitude of a physical quantity (length, Mass and Time).
• A unit of measurement is definite
Ask
• You could ask the definition of Unit.
• Ask about systems of measurement.
• Ask about different types of units.
Elaborate
A unit of measurement is a definite magnitude of a physical quantity (length, Mass and Time). Example:
10 liter, 200 meter, 20 kg
However, now-a-days SI (International System of Units) is used across the globe as a standard system of
measurement. It is an extension of MKS system of measurement.
SI system has 7 fundamental units and 2 supplementary units, there are a number of derived units.
S. No Measuring S I Units
1. Length Meter
2. Mass Kilogram
3. Time Second
4. Intensity of Electric current Ampere
5. Thermodynamic Temperature Kelvin or degree Celsius
6. Quantity of substance Mole
Table 1.2.2: 7 fundamental units of SI system
16
Welding and Quality
Technician
17
Facilitator Guide
Say
• A measuring instrument is a device used for measuring a physical amount. In the physical sciences,
quality confirmation and engineering, estimation is the movement of getting and contrasting physical
amounts of certifiable items and events.
• Measuring instruments are classified into types:
1. Linear Measurement: Linear Measurement includes measurement of lengths, diameters, heights,
depths, thickness etc.
2. Angular Measurement: Angular Measurement includes measurement of angles, tapers etc.
• Some common instruments used in measurement are; steel rule, callipers, surface plate, plug gauge,
micrometer, dial gauge etc.
Do
• Show different precision and non-precision instruments.
• Give the example of least count calculation.
Steel Rule
Say
• Steel Rule is a flat and thin linear measurement instrument. It is the most commonly used measuring
instrument.
• There are different types of rules available. Few commonly used are: Engineer’s rule, Folding rule,
• Flexible rule & Hook rule
Do
• Show different steel rules
• Demonstrate the use of steel rule
18
Welding and Quality
Technician
Elaborate
Steel Rule is a flat and thin linear measurement instrument. It is the
most commonly used measuring instrument. Steel rule is manufactured
from stainless steel. The edges of the rule are accurately ground to form
straight edges. Steel rules are available in different sizes like 150 mm,
300 mm and 600 mm. usually; the reading accuracy is around 0.5 mm.
Calipers
Say
• Calipers are measurement devices used to measure distance between two opposite ends of an ob-
ject.
• A caliper can be as simple as a drafting compass, with inwards or outward facing points. The tips of
the caliper are adjusted to fit across the points to be measured, the caliper is then stretched and the
separation between the tips is measured with a measuring device, such as a ruler.
• Few common types of calipers are:
• Inside Caliper: These calipers are used to measure inside size of an object. The caliper can be
manually adjusted or screw-adjusted.
• Outside Caliper: These calipers are used to measure external size of an object. These are com-
monly used to measure pipe diameters.
• Divider Caliper: In metal working, divider calipers are used for marking work-pieces. The tips are
sharpened to act as scribers, one leg can then be located in the dimple made by a center or prick
punch and the other leg pivoted so that it scribes a line on the work-piece’s surface, thus forming
an arc or circle.
• Odd leg or Jenny Calipers: These calipers have one straight pointed leg and other inward curved
leg. These are generally used for marking lines parallel to straight edges and also for transferring
dimensions. Odd leg or Jenny calipers are also used to find center of a rod.
Do
• Show different types of calipers.
• Demonstrate how to use the caliper.
19
Facilitator Guide
Micrometer
Say
• Micrometers are precision measurement devices that are used to measure small dimensions. There
are two types of micrometers viz. inside and outside.
• Outside micrometers are used to measure shafts, pipe, plate thickness etc.
• Inside micrometers are used to obtain measurement of internal sizes like diameters of holes, pipes
etc.
• Micrometers use the principle of a screw to increase small distances (that are too small to measure
directly) into large rotations of the screw that are big enough to read from a scale.
Do
• Show micrometer.
• Show the parts of micrometer.
• Demonstrate how to take the reading from micrometer.
Elaborate
A micrometer is used to measure very small distances.
Body parts of a Micrometer
20
Welding and Quality
Technician
• Frame: Frame of a micrometer is a C-shaped component that clamps the other parts of the
micrometer. The frame is usually made of drop-forged steel and is heavy with high thermal mass.
The high thermal mass is to prevent heating up and to reduce flexion, expansion and contraction.
• Anvil: The projected portion of the frame, which extends to at least 3mm, is known as anvil.
It is one of the measuring faces. An anvil is manufactured from alloy steel and in finished to a
perfectly flat surface.
• Spindle: The spindle of a micrometer grips the job against the anvil. The movement of the thimble
causes the spindle to move towards the anvil.
• Sleeve: It is also known as barrel or stock. Sleeve is a stationary round part on which datum line
and graduations are marked.
• Thimble: It is a cylindrical cover attached to the spindle and moves with the spindle. It is has a
beveled edge and is divided into 50 equal parts. The divisions are marked as 0, 5, 10, 15…... 45.
• Ratchet Stop: It is an extension to the thimble. Ratchet stop ensures even pressure between the
gauging surfaces.
• Lock Lever or Lock Nut: It is used to lock the spindle at a desired position.
Demonstrate
• Explain the parts of micrometer.
• Demonstrate how to do measurement from micrometer.
21
Facilitator Guide
Activity
• Conduct a skill practice activity.
• Ask the students to assemble together.
• Explain the purpose and duration of the activity.
• Set guidelines pertaining to discipline and expected tasks.
• Do the measurement of given object by using micrometer
Do
• Show different types of calipers.
• Demonstrate how to use the caliper.
Vernier caliper
Say
• A Vernier calliper is a measuring instrument that precisely measures (read) distances more accurately
than a normal scale or rule. It is simply a Vernier scale mounted on a measuring instrument.
• Vernier Calipers are available in both digital and manual versions. This instrument can be used to
measure internal as well as external dimensions.
• The Least Count of a Vernier Caliper can be calculated using the formula LC = 1 MSD - 1 VSD (Value of
one Main Scale Division - Value of one Vernier Scale Division).
Do
• Show vernier caliper.
• Demonstrate how to take the reading from vernier caliper.
22
Welding and Quality
Technician
Elaborate
For using vernier caliper, move the position of the pointer on the scale. At the point where the pointer is
between two markings, take the reading on the scale. This is basic caliper; expansion of vernier scale on
the instrument gives more exact reading; this is the vernier caliper.
Demonstrate
• Explain the parts of vernier caliper.
• Demonstrate how to do measurement from vernier caliper
23
Facilitator Guide
Step2: Close the jaws lightly on the item which you want to
measure (For example a round steel ball).
Step3: The main metric scale is read first and for example
says this shows that there are 13 whole divisions
before the 0 on the hundredths scale. Therefore, the
first number is 13.
Step4: The ‘hundredths of mm’ scale is then read. The most
ideal to check the quantity of divisions until you Fig. 1.2.4: Reading Vernier Caliper
get to the division that lines up with the fundamental metric scale. This is 21 divisions on the
hundredths scale.
Step5: This 21 is multiplied by 0.02 giving 0.42 as the appropriate response (each division on the
hundredths scale is equal to 0.02mm)
Step5: The 13 and the 0.42 are added to give the last result of 13.42mm (the diameter of the piece of
round section steel).
Activity
• Conduct a skill practice activity.
• Ask the students to assemble together.
• Explain the purpose and duration of the activity.
• Set guidelines pertaining to discipline and expected tasks.
• Do the measurement of given object as per drawing by using vernier caliper
Drawing or sketch
Do
• Ask them to practice the activity alone.
• Go around and make sure they are doing it properly.
• Wrap the unit up after summarizing the key points and answering questions.
24
Welding and Quality
Technician
Height gauge
Say
• A digital height gauge is precision measuring device used specifically for measuring height of two
points.
• Advanced electronic (digital) height gauges can be used to carry out different tasks like measuring
step heights, internal/external diameters and centre-line distances.
Do
• Show height gauge.
• Demonstrate how to take the reading from height gauge.
Elaborate
The electronic height gauge has a precision of up to 0.0254 mm and
claims consistency of ±0.00254 mm. The conventional height gauges
are similar to Vernier Callipers, except that the fixed jaw is shaped
like a base. The scale is graduated on both sides, one side being
graduated for internal measurement. The main scale for external
measurement starts at 1 inch. This allows for the combined width of
the base and movable jaw, when the jaws are in contact. The gauge
can be converted into a form of scribing block (to mark the work
piece) by attaching an extension arm, beveled to a sharp edge, to the
movable jaw.
Fig. 1.2.5: Height Gauge
Activity
• Conduct a skill practice activity.
• Ask the students to assemble together.
• Explain the purpose and duration of the activity.
• Set guidelines pertaining to discipline and expected tasks.
25
Facilitator Guide
Drawing or sketch
Do
• Ask them to practice the activity alone.
• Go around and make sure they are doing it properly.
26
2. Gas Metal Arc Welding
(GMAW) – Before Welding
Unit 2.1 – Why GMAW
Unit 2.2 – Parts of a GMAW Machine and Accessories
Unit 2.3 – Setting Up a GMAW Outfit
Unit 2.4 – Operating Parameters of GMAW
Unit 2.5 – Process Parameters of GMAW
Unit 2.6 – Applications of GMAW
ASC/N3103
Facilitator Guide
28
Welding and Quality
Technician
Unit Objectives
At the end of this unit, Students will be able to:
1. List the reasons why GMAW is popular.
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster, participant manual.
• PC with LCD Projector or Flip Chart
Do
• Greet and welcome the participants to the next session of the program.
• Before starting the session ask them do they have any doubts pertaining to the previous unit.
• Capture their responses on board and share them wherever necessary.
Say
• GMAW or Gas Metal Arc Welding was introduced in the late 1940’s and has been the most popular
forms of welding till now.
• It is a mechanised process.
• As compared to other processes, GMAW proves to be more efficient and more reliable in terms of
reducing defects and producing a strong weld.
Elaborate
Merits of GMAW
• Usability: The degree of usability with the GMAW process is very high as compared to other
processes. The GMAW process can be used to weld all metals with appropriate filler metal and
gas. These include carbon steel, alloy steels, stainless steel, aluminium, cast iron, etc.
29
Facilitator Guide
• High Strength: In the GMAW process, due to the small size of electrode, current density is very
high and so is the strength of the weld metal is high.
• High Productivity: Productivity is defined by the rate of metal deposition. Metal deposition is
governed by the current density. Since current density is much higher in GMAW process than
in SMAW, the productivity is also very high.
• Less Distortion: The main reason for lesser distortion is less heat input. Heat input in GMAW is
very less when compared to that in SMAW.
• Savings in Consumables: The consumable which is used in GMAW is considerably far less than
in SMAW, for a job of similar nature.
• Error Reduction: The GMAW process is considerably enhanced and improved over other
methods of welding. This is done by automation of the process. It is a mechanized process and
the quality of the weld does not primarily depend on the skill of the welder.
• Ease of Operation: The basic reason for this is fewer starts and stops during welding by the
GMAW process. This is because the welder needn’t stop the welding process to change the
electrode. The electrode is fed automatically. Therefore, the welder has to only concentrate on
one motion, thus making it easier for him to operate the GMAW process.
• Single Size of Consumable: In GMAW process, we use a single size of consumable, to do welding
on thin to thick plates. Thus, the GMAW process, not only saves the need for changing the
electrodes, but it also saves on inventory.
Ask
• Ask about need of GMAW process
• Ask about advantages and limitations of GMAW process
30
Welding and Quality
Technician
31
Facilitator Guide
Unit Objectives
At the end of this unit, Students will be able to:
1. Identify the parts of a GMAW machine;
2. State the function of each part.
Resources to be Used
• Facilitator can use the available objects such as a marker, duster, pen, notebook, participant manual
etc.
• PC with LCD Projector or Flip Chart
• GMAW machine and its associated parts.
Do
• Greet and welcome the participants to the next session of the program.
Say
• GMAW machine has following parts:
o Accessories,
o return cable with earth clamp,
o torch,
o helmet with shaded glass,
o welding cables,
o wire feeder,
o base plates,
o gas cylinder,
o power source,
o work table,
o interconnection cable and
o PPE.
32
Welding and Quality
Technician
Elaborate
Various parts of a GMAW machine and their functions are:
• Gas: The gas shields the weld metal from atmosphere contamination; thus strengthen the
weld. The selection of gas has to be made on the basis of material and process requirement.
The commonly used shielding gases for GMAW process are carbon dioxide, argon, helium and
their mixtures.
• Power Source: The power source delivers the power to strike an arc for welding. The power
source input supply is 440/220 volts from the Electricity Board.
For welding operation, high current, low voltage is required. The power source converts the
input supply of high voltage, low current to low voltage, high current. All GMAW power sources
are constant potential power sources. The types of power sources are rectifier power source,
thyristor rectifier power source and inverter power source.
• Wire Feeder: Unlike SMAW process, GMAW has a wire feeding mechanism. Current is nothing
but the wire feed rate, which is set on the wire feeder. The wire feeder is a two-roll/ four-roll/
planetary drive mechanism operating on pinch force effect.
• Torch: The torch is the business end of the operation. This is because the torch is where all the
parameters come into action, allowing it to deliver the power to generate the arc.
Torches are available in gas-cooled and water-cooled, as well as in unitised and non-unitised
versions. The appropriate torch is chosen on the basis of the duty cycle of operation. Torch
conveys the wire from the outlet of the wire feeder to the arc zone through a contact tip. The
wire is energised only at the contact tip, just before it arcs and gets deposited as weld metal.
The torch also conveys the gas to the weld zone to provide a protective shield.
Since the torch is directly in the heat area, certain components of it are classified as consumable
spares. These are bound to wear off over a period of usage. Eg., contact tip, nozzle, tip holder,
etc.
• Continuous Filler Wire – Welding Consumable: The continuous filler wire draws the current
to generate the heat on striking an arc. Welding consumable is selected based on the base
material. Normally, for carbon steel, the continuous filler wire is of the grade ER 70S6. For 308
stainless steel grade material, ER308L grade material filler is used.
• Gas Cylinder with Regulator and Flow Meter: The gas cylinder provides the shielding gas,
which is needed to secure the weld metal. The gas is filled in the cylinder under high pressure.
A regulator is used to release the gas at operating low pressure range. The flow of the gas is
further regulated using a flow meter, which is attached to the outlet of the regulator.
• Welding Cables: The welding cable conveys the power from the power source to the torch
which is connected to the wire feeder. Correct size of cables as per recommendation, based on
the current delivered, has to be used.
• Interconnection Cable: The interconnection cable or control cable delivers the power required
for the wire feeder from the power source. It delivers the power required for the function of
33
Facilitator Guide
the wire feeder motor. It also delivers the power for the operation of solenoid valve, which
controls gas flow.
• Gas Hoses: The gas hoses deliver the gas from the cylinder to the welding area through the wire
feeder and torch.
• Helmet with Shaded Glass: The helmet is used to view the arc through the suggested shaded
glass as per the recommendation. It facilitates the use of both hands for effectively controlling
the weld puddle.
• Accessories: Welding accessories include the earth clamp with cable, wire brush and chipping
hammer. The accessories are used to finish the post operations after welding.
• Personal Protective Equipment (PPE): The PPE protects the welder from the ill-effects of heat
and light.
Do
• Show all the parts of GMAW machine.
• Demonstrate the functioning of GMAW machine Parts.
• Allow students to use and operate the GMAW machine Parts.
Activity
• Place all the Parts of GMAW machine on a table.
• Call each student one by one and ask them to identify the Parts you called.
• Tell the student to brief the functioning and required parameter of that Parts.
34
Welding and Quality
Technician
Unit Objectives
At the end of this unit, Students will be able to:
1. Set up a GMAW outfit such that it is ready for the welding process;
2. Implement maintenance of welding equipment.
Resources to be Used
• Facilitator can use the available objects such as a marker, duster, pen, notebook, participant manual
etc.
• PC with LCD Projector or Flip Chart
• Welding accessories, return cable with earth clamp, torch, helmet with shaded glass, welding cables,
wire feeder, base plates, gas cylinder, power source, work table, interconnection cable and PPE.
• Parts to be welded and their drawings.
Do
• Greet and welcome the participants to the next session of the program.
Say
• Different components are required for setting up a GMAW outfit i.e.
o Accessories,
o return cable with earth clamp,
o torch,
o helmet with shaded glass,
o welding cables,
o wire feeder,
o base plates,
o gas cylinder,
o power source,
o work table,
35
Facilitator Guide
Demonstrate
Setting up the Cylinder
1. Attach the cylinder to the stand.
2. Flush out some gas to clear the valve of dust.
3. Connect the regulator to the outlet valve of the cylinder.
4. Open the cylinder slightly so that the regulator registers the cylinder pressure at the inlet gauge.
5. Connect the flow meter to the regulator.
6. Connect the gas hose to the flow meter and power source or wire feeder.
7. Engage the knob in the regulator.
36
Welding and Quality
Technician
2. Ensure that the welding cable from the positive terminal has been connected to the wire feeder
without any loose connection.
3. Ensure that the control cable or interconnection cable from the wire feeder is joined to the power
source rigidly.
4. Connect the return earth cable from the negative terminal of the power source using an earth
clamp onto the work table.
5. Turn on the main switch to enable the power source to be connected with the electricity board
supply.
6. Set the ON/OFF switch in the ‘ON’ position to energise the power source.
Elaborate
Preventive or Self Maintenance of Welding Equipment
1. Drive Rolls Not Cleaned or Adjusted Properly: This can cause the tensioning and hold on the
wire. Knurled rolls used for FCAW wires are more influenced than Smooth rolls used for solid
wire.
Solution: To remove the accumulation of drawings compound, dust and dirt that would cause
the pressure and grip the rolls would have on the wire, clean the drive rolls with a wire brush
occasionally by removing them.
2. Drive Roll Pressure Too High: When a feeding problem arises, to tighten the drive rolls in order to
grip the wire better. Using drive roll pressure, the flux-cored wire can change its shape from round
to oval, which is possible due to its construction. This wire also develops ‘teeth’ when knurled
rolls are used. These teeth wears the liner, guides, and tip like a saw.
Solution: Occasionally, an air nozzle and shop air pressure to blow out the liner can be used
before feeding the wire through the cable/hose assembly. This can be done initially from the
torch end and then, if possible, from the feeder end.
3. Worn Spring Liner: The spring liner can be utilized for almost all cable/hose assemblies since it is
detachable and replaceable. Nearly all spring liners have at least two constant bends. One coming
out of the feeder, the other in the torch neck. The wire brushes the same spot and wears a groove
in the liner. This turns out to be a high-friction area as the groove deepens, and the more bends
that are permanent increases the drag on the wire, causing it to “birdnest” at the torch inlet or
just stop feeding.
Solution: A kink in the liner will cause a feeding problem. Blow out the liner guide, turn the liner
90°-180° and reinstall it, this will present a fresh area in the liner to the wear of the moving wire.
4. Diffuser / Tip Problems: The most commonly replaced item in a torch assembly is the tip.
37
Facilitator Guide
Solution: Besides from normal wear that results in the need for replacement, the tip is rarely the
cause of feeding problems. But, it does show the results of the problem. There is a guarantee that
the issue is developed in one of the discussed areas if the tip has been supplanted and feeding
problems continue.
5. Check Your Ground: A bad ground can introduce itself as a stutter and make the wire execute as if
it needs voltage or speed change. A lack of shielding gas coverage, liner or tip grab, or base metal
contamination, will cause porosity.
Solution: Intermittently check the ground at the power source, wire feeder, and work clamp. A tip
with burn-back and spatter can be abolished by a bad ground.
The utilization of commonly available wire lube and cleaner, good for MIG and FCAW is one of the
easiest approaches to keep up feeding characteristics, if everything else is correct. Another good idea
for protecting the consumables (nozzle and tip) is nozzle dip. These products won’t correct for drive rolls
issues, worn liners, or weak grounds, however, when utilized by the manufacturer’s suggestions and the
previously mentioned tips, they will promote much longer component life, fewer feeding problems, and
many more effective working hours than bad ones.
Activity
• Conduct a skill practice activity.
• Ask the students to assemble together.
• Explain the purpose and duration of the activity.
• Set guidelines pertaining to discipline and expected tasks.
38
Welding and Quality
Technician
Do
• Divide the class into pairs.
• Go around and make sure they are doing it properly.
• Wrap the unit up after summarizing the key points and answering questions.
39
Facilitator Guide
Unit Objectives
At the end of this unit, students will be able to:
1. List the parameters of a GMAW process;
2. Identify the part required to set the parameters of a GMAW process.
Resources to be Used
• Facilitator can use the available objects such as a marker, duster, pen, notebook, participant manual
etc.
• PC with LCD Projector or Flip Chart
Do
• Greet and welcome the participants to the next session of the program.
Say
• Current, current density, voltage, stickout, gas flow rate and travel speed are the key operating pa-
rameters of GMAW.
• Current is responsible for melting the wire and the base plate.
• Voltage is the pressure or the force which drives the current.
• Stickout is defined as the length of the wire which is protruding outside from the contact tip.
• Gas flow rate defines the amount of shielding gas flowing through the nozzle to provide effective
shielding for the weld metal from atmospheric contamination.
• Travel Speed is defined as the speed at which the welding progresses. Its unit is normally in millime-
tres per minute (mm/m).
Elaborate
Current
In GMAW, the current is nothing but the wire feed speed. In other words, the more the wire that comes
40
Welding and Quality
Technician
out of the torch, more current is required to melt the wire and deposit it as a weld metal. More wire
requires more current, and less requires less current.
Current is set by the current potentiometer knob, which is usually on the wire feeder. This knob controls
the wire feeder motor speed.
For example, say you are welding two 10 mm plates edge prepared so as to form a single V joint with an
included angle of 60 degrees and with a root face of 2 mm. A fit up for groove welding is made with the
above plates with a root gap of 2 mm. The root run is made on the root face so as to bridge the gap with
full penetration. Hence, the effective thickness for the root run is 2 mm in spite of the plate thickness
being 10 mm. So the welding area thickness for the root run is 2 mm.
The thumb rule for current calculation is 40 A/ mm welding area thickness. So, the required current for
root run is 80 amps.
Voltage
In all forms of welding, voltage digs a pit and current melts the metal to fill the pit. Hence, current and
voltage are related to ensure that the pit dug by the voltage is filled with adequate metal by current.
The voltage is set using a potentiometer or multi-position switch on the power source.
Voltage can be calculated by using an empirical formula from the above calculated current. The empirical
formula varies for different shielding gases.
V = 14 + 0.05I
V = 12 + 0.05I
Stickout
The actual operating voltage is the outcome of the set voltage and stickout. If the stickout increases, the
actual operating voltage will decrease for a set voltage, and vice versa.
The normal stickout range tends to vary from 10 to 15 mm. However, larger stickouts, more than 15 mm
can also be utilized by bringing in corresponding change in the gas flow rate, if needed.
The gas flow rate is set on the flow meter which is fitted onto the regulator. The regulator regulates the
pressure of the gas from the cylinder to operating pressures.
41
Facilitator Guide
The normal range of gas flow rate for a stickout of 15 mm shall be around 12 to 15 litres per minute when
operating in a closed welding shed.
Exposure of the weld metal to atmosphere leads to porosity, which leads to a weak weld. Hence, utmost
precaution has to be taken to avoid direct exposure of the welding area to the wind path.
In case of higher stickout, a small increment in gas flow rate is needed to ensure effective shielding.
Travel Speed
The travel speed depends totally on the welder’s hand movement, which depends on the metal deposition.
In GMAW, the operating travel speed is influenced by technique, current, voltage and stickout. Being a
high productive process, the normal travel speed for semi-automatic operation shall be in the range of
250 to 300 millimetres per minute.
Ask
• You could ask about different operating parameters of GMAW.
• Ask about operating ranges of parameters for different welding thicknesses.
42
Welding and Quality
Technician
Unit Objectives
At the end of this unit, students will be able to:
1. List the modes of metal transfer in a GMAW process;
2. Select the process parameters based on the nature of the job.
Resources to be Used
• Facilitator can use the available objects such as a marker, duster, pen, notebook, participant manual
etc.
• PC with LCD Projector or Flip Chart
Do
• Greet and welcome the participants to the next session of the program.
Say
• The process parameters for GMAW are defined with different types of metal transfers.
• In SMAW, different sizes of electrodes are utilized for different operations. Whereas, in GMAW; single
size of electrode can utilize for all operations in the different types of welding processes.
• There are different modes of metal transfers, depending upon the various operating parameters:
short circuit transfer, globular transfer and spray transfer.
Elaborate
Modes of Metal Transfers
1. Short Circuit Transfer: In this metal is transferred by literally short circuiting the wire and the base
plate. This is also called as ‘dip transfer’. This transfer mode is achievable with all shielding gases
and operates with low currents and low voltages. This mode of transfer is used to bridge gaps, in
sheet metal operations and root runs.
43
Facilitator Guide
Since the main operating parameters are current and voltage, other parameters can be defined
easily with help of these two parameters. The following chart gives a relationship between
current, voltage and wire size.
2. Globular Transfer: In this, the metal is transferred by means of big globules. This is medium
current, medium voltage transfer. Globular transfer is normally used after root welding for higher
productivity. Since metal is transferred in globules, there is possibility of spatter to occur in this
mode of transfer. In globular transfer mode, 100% carbon dioxide is used. It can be used only in
down hand and horizontal positions. The following chart gives a relationship between current,
voltage and wire size.
3. Spray Transfer: In this, the metal is sprayed from the torch to the base plate in the form of fine
droplets. This is a high current, high voltage transfer process. Spray transfer is normally used
after root welding for high productivity. The gases used are argon and its mixture, where the
percentage of argon is more than 80%. This mode is used only in the down hand position. The
following chart gives a relationship between current, voltage and wire size.
Ask
• You could ask about various metal transfer methods used.
• Ask about current and voltage parameters of different metal transfer methods.
44
Welding and Quality
Technician
45
Facilitator Guide
Unit Objectives
At the end of this unit, Students will be able to:
1. Explain applications of GMAW in different industries.
Resources to be Used
• Facilitator can use the available objects such as a marker, duster, pen, notebook, participant manual
etc.
• PC with LCD Projector or Flip Chart
Do
• Greet and welcome the participants to the next session of the program.
Say
• GMAW is popular due to its speed and versatility in various industries.
• GMAW – Applications
46
Welding and Quality
Technician
Ask
• You could ask about industrial use of GMAW.
Field Visit
• Take the trainees to industries.
• Show them the use of GMAW in industries.
47
Facilitator Guide
Notes
48
3. Shielding Gas
Unit 3.1 – Why Shielding Gas
Unit 3.2 – Shielding Gas Selection
ASC/N3103
Facilitator Guide
52
Welding and Quality
Technician
Unit Objectives
At the end of this unit, Students will be able to:
1. Describe the functions of shielding gas;
2. Explain the types of shielding gas.
Resources to be Used
• Available objects such as white board marker pens, duster, participant manual etc.
• PC with LCD Projector or Flip Chart
Do
• Greet and welcome the participants to the next session of the program.
• Before starting the session ask them do they have any doubts pertaining to the previous unit.
• Capture their responses on board and share them wherever necessary.
Say
• Shielding gas provides shielding for liquid metal from atmosphere.
• It also provides
o Ignition of arc;
o Arc stability;
o Wetting between the solid material and the weld pool;
o Penetration – Depth and shape of the weld bead;
o Spatter formation
• Shielding gas is classified into two types: Active Gas and Inert Gas
53
Facilitator Guide
Elaborate
Types of Shielding Gas
1. Active Shielding Gas: e.g.: CO2
CO2 gas at arc zone disassociates into carbon monoxides and oxygen, and immediately
recombines to form CO2 slightly above the arc zone. This reaction produces extra amount of
heat (exothermic reaction) which is utilized for welding operations.
2. Inert Shielding Gas: e.g.: Argon, Helium
Inert gases do not participate in the dynamics of arc welding and restrict themselves only to
the extent of providing shielding to the liquid metal. They also contribute to the arc stability.
Ask
• Ask students about need of shielding gas
• Ask about different types of shielding gases utilized
54
Welding and Quality
Technician
Unit Objectives
At the end of this unit, students will be able to:
1. List the metals that can be welded;
2. Select shielding gas for the identified base material (metal).
Resources to be Used
• Available objects such as white board, marker pens, duster, participant manual etc.
• PC with LCD Projector or Flip Chart
Do
• Greet and welcome the participants to the next session of the program.
• Before starting the session ask them do they have any doubts pertaining to the previous unit.
Say
• All types of material can be welded by right type of filler material and gas combinations.
• List of shielding gases available are:
o CO2
o Argon
o Argon CO2 gas mixer (ACM) in various combinations like: 80/20, 95/5, 90/10 etc.
o Argon oxygen gas mixer – 98/2 (Argon -98/Oxygen-2)
o Argon/Helium
o Argon/Helium/Oxygen
o Argon/Helium/ CO2/H2
55
Facilitator Guide
Elaborate
Selection of Shielding Gas
Ask
• Ask students about need of correct selection of shielding gas
• Ask about selection criteria of shielding gases
56
4. Safety
Unit 4.1 – Hazards in Welding
Unit 4.2 – Personal Protective Equipment (PPE)
Unit 4.3 – Fire Safety
Unit 4.4 – First Aid for Electric Shock and Burns
Unit 4.5 – 5S
ASC/N0006
ASC/N0021
Facilitator Guide
58
Welding and Quality
Technician
Unit Objectives
At the end of this unit, you will be able to:
1. Identify different kinds of hazards that a welder faces;
2. State the ways to avoid these hazards.
Resources to be Used
• Available objects such as a duster, pen, notebook, hazard warning sign etc.
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• A hazard is something that has the potential to cause injury, disease or death in a workplace.
• There are a number of aspects to the development of a safe workplace environment.
o The development of policies
o The development of consultative processes
o Hazard identification, assessment and control.
• A welding shop is full of hazards at every step of its operation. These hazards are to be tackled for the
sake of safety in the workshop.
• Environment protection and hazardous material.
Elaborate
Different Types of Hazards
• Fumes and Gases: Fumes and gases can be hazardous to your health as they contain various
poisonous chemicals.
59
Facilitator Guide
Ask
• You can ask the different types of hazard
• You can pick the students and ask the hazard warning sign.
• You can ask the different ideas to control the hazard.
• You could ask the most common hazard in welding shop.
Activity
• Conduct a skill practice activity.
• Ask the students to assemble together.
60
Welding and Quality
Technician
Do
• Ask them to get into pairs for practice.
• Go around and make sure they are doing it properly.
61
Facilitator Guide
Unit Objectives
At the end of this unit, you will be able to:
1. List the different kinds of protective equipment that a welder must use;
2. Identify the use of each piece of protective equipment.
Resources to be Used
• Available objects such as a duster, pen, notebook, PPE etc.
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• Personal protective equipment serves as the last resort for controlling hazards and is one, but not the
only, ancillary or temporary measure.
• To make full and proper use of personal protective equipment, one should first make sure that the
equipment can fulfill the working requirements, conform to the required standards, fit the body
shape of the user, be user-friendly, and is under regular maintenance and can be replaced if necessary.
Elaborate
Personal Protective Equipment and accessories required
• Welding Helmet: A welding helmet is worn on the head to protect the welder during welding.
• Filter Lens: The filter lens enables the welder to see the weld pool at the same time its dark.
The lens protects the welder’s eye from extreme bright light.
• Leather Apron: Leather is worn to protect the welder from spatters during welding and from
arc rays.
62
Welding and Quality
Technician
• Leather Gloves: They protect the welder from sparks, arc rays and spatters during welding.
Gloves also protect the welder from hot objects.
• Leather Sleeves: Leather sleeves are worn by the welder to protect him from spatter, arc rays
and sparks during welding.
• Leggings: Leggings are worn over the ankle. They stop hot spatter or sparks from entering the
shoe.
• Safety Shoes: Safety shoes serve as an insulator. They also save the foot from spatters; arc rays
and sparks during welding.
• Safety Helmet: A safety helmet is worn on the shop floor during grinding etc. to guard the
wearer from falling objects or flying splinters.
• Clear Glass Goggles: Clear glass goggles are worn during operations like grinding to protect the
eyes from flying splinters.
• Ear Muffs/Plugs: They protect the welder from high noise levels on the shop floor. They also
stop any splinters from entering the ears.
• Dust Mask: A dust mask is worn to protect the wearer from fine dust which is made up mainly
of fine metal particles.
• Gas Mask: A gas mask is a mask put on over the face to protect the welder from inhaling
pollutants and toxic gases.
Ask
• You can pick the students and ask the safe practices for avoiding general shop hazards.
• You can ask the various types of personal protective equipment.
Do
• Show them the PPE
• Demonstrate the use and requirement of PPE
63
Facilitator Guide
64
Welding and Quality
Technician
Unit Objectives
At the end of this unit, You will be able to:
1. Identify the causes of fire at the shop floor;
2. List the dos and don’ts to prevent fire;
3. Explain how to deal with a fire accident;
4. Describe the different safety precautions at workplace.
Resources to be Used
• Available objects such as a duster, pen, notebook, fire extinguisher and fire safety equipments etc.
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• Fire is defined as a self-sustaining combustion process in which a substance (fuel) combines with
oxygen in air to produce immense heat and light.
• Spatter, arc rays and sparks can cause fire during welding if they fall on combustible materials like
petrol, wood, acetylene, hydrogen or oxygen cylinders and electrical fittings.
• Electrical fires are different from regular fires. They cannot be extinguished with water. To put out an
electrical fire, the right type of fire extinguisher must be used.
• A fire extinguisher, or extinguisher, is an active fire protection device used to extinguish or control
small fires, often in emergency situations.
65
Facilitator Guide
• Types of fire extinguisher relevant to welding shop are sand, water, foam, dry chemical powder (DCP)
and CO2.
o the people responsible for health and safety at the work place;
o the name, designation and location of the person responsible to contact at the time of emergency;
o the names and location of the documents that refer to health and safety.
• Efforts should be taken to reduce the scale & probability of hazards. Effective action is required during
emergency situation. For dealing emergencies, effective action is possible with good training and
actual practice on the procedure for dealing such emergencies.
• Mock Drills is a situation in which fake emergency is announced and workmen are asked to follow
emergency evacuation plan. This allows the workman to familiarize with the emergency situation and
act according to plan.
Elaborate
Safety Precautions
In case a fire breaks out, then
• If it is a small fire use a fire extinguisher.
• If the fire is big, call the fire brigade.
• All those on the shop floor should move towards the exit.
Electric Shock
• Make sure the machine is properly grounded.
• Never permit “live” parts of the electric welding machine to touch bare skin or wet clothing.
• Do not cool electrode holders by putting them in water.
• Turn off power supply when the welding machine is not in use.
• Avoid standing on damp areas while welding.
• Wear leather gloves.
• Ensure that the cables are protected and are in good condition.
• Ensure that electrode holders are correctly insulated.
66
Welding and Quality
Technician
Burns
• Guard your eyes and face from flying particles of slag by using safety glasses or face shield.
• Always wear leather gloves.
• Wear safety shoes.
• Avoid touching the electrode or metal where welding has taken place.
• Hold hot metal with pliers or tongs.
• Keep electrode stubs appropriately arranged off.
Radiant Energy
• Protect your head and eyes with a welding helmet and the right shade lens.
• Avoid leaving bare skin exposed to the rays of the arc, wear suitable clothing.
• Never strike the arc without protecting the face and eyes.
• Never look directly at the arc where others are welding without suitable eye protection.
Gases & Fumes
• Work only in well-ventilated areas and work on stations with exhaust systems.
• Be extra careful when working on metals covered with lead or zinc.
• Use respirator or other approved breathing devices if operating in a restricted area.
Combustible Materials
• Keep shop clean in areas where welding is to be done.
• Never weld near inflammable materials of any kind.
• Never weld on shielded containers which may have held inflammable materials without first
taking appropriate safety precautions.
Fire Protection
• Get acquainted with location and types of fire extinguishers.
• Report any risky conditions that may begin a fire.
• Never weld near combustible materials.
• Never weld near electrical fittings or lines.
• Attend training on evacuation procedures during mock practice.
Trips & Falls
• Keep work areas clear of equipment, machines, cables and hoses.
• Always properly maintain and use handrails.
• Always use and maintain safety lines, harnesses and lanyards.
67
Facilitator Guide
Safety Signages
It is important to know the meaning of safety signs. Such signs warn us of danger and allow us to take
precautions to keep safe. There are four main types of safety signs:
• Prohibition signs
• Mandatory signs
• Warning signs
• Information signs
68
Welding and Quality
Technician
69
Facilitator Guide
Demonstrate
Steps for using the fire extinguisher
STEP 1: Pull the Pin at the top of the extinguisher. The pin releases a locking mechanism and will allow
you to discharge the extinguisher.
STEP 2: Aim at the base of the fire, not the flames. This is important - in order to put out the fire, you
must extinguish the fuel.
STEP 3: Squeeze the lever slowly. This will release the extinguishing agent in the extinguisher. If the
handle is released, the discharge will stop.
STEP 4: Sweep from side to side. Using a sweeping motion, move the fire extinguisher back and forth until
the fire is completely out.
STEP 1: Gathering Facts: Collect and note all the facts, including –
• Date, time, and location of accident
• Names, job titles, workers and immediate supervisor involved
• Events leading up to the accident
• Job that a worker was handling at the time of the accident
• Names of workers/supervisor who witnessed the accident
• Surrounding conditions (e.g. greasy floor, insufficient lighting, noise, etc.)
• Circumstances at the time of accident (including tasks, equipment, tools, materials, etc.)
• PPE worn by the worker at the time of the accident
• Injuries that occurred (name of the injured body part and characteristics and extent of inju-
ries)
• Type of treatment for injuries (first aid if given)
• Damage to equipment, materials, and the worker was working on or any other equipment or
material around it.
70
Welding and Quality
Technician
STEP 2: Determining the Sequence: Describe this sequence in events after gathering the facts –
• Events leading up to the accident: Task the worker was performing at the time of ac-
cident. For example: bending over, climbing, lifting operating machinery, etc.
• Events involved in the accident: Was the employee struck/caught in the machine or
caught in the fire? Did the worker fall on the same level or from a height?
• Events immediately following the accident: What did the employee do: started
bleeding? Body caught fire? Complain about back pain? Put Response from other
workers/supervisor. Did they call for help, administer first aid, shut down equipment
etc.?
STEP 3: Analysing: Analyse of the causes of the accident.
• Conducting a job hazard analysis to evaluate the task for any other hazards
• Engineering changes that make the task safer or administrative changes that might include
changing the way the task is performed.
Tips
How to Prevent Fire
Dos Don’ts
Keep welding area clean. Do not wear inflammable materials like nylon etc.
If empty containers contain flammable materials, Never weld near electrical lines.
fill them with water.
Report any unsafe situation that may cause a fire. Never weld near combustible materials.
Watch where the sparks and metals are falling Never leave any cable without insulation.
from your work.
71
Facilitator Guide
Ask
• You could ask the common fire extinguisher.
• You could ask the type of fire extinguisher and their role?
• You could ask what all information contains fire drill report.
Activity
• Conduct a skill practice activity.
• Ask the students to assemble together.
• Explain the purpose and duration of the activity.
• Set guidelines pertaining to discipline and expected tasks.
72
Welding and Quality
Technician
Do
• Ask them to get into pairs for practice.
• Go around and make sure they are doing it properly.
• Wrap the unit up after summarizing the key points and answering questions.
Field Visit
You could visit any of the industry and show the firefighting equipment. With the help of field visit you
could show the where we need to fit various firefighting equipment and its role.
73
Facilitator Guide
Unit Objectives
At the end of this unit, You will be able to:
1. Describe how to give first aid in case of burns and shocks.
Resources to be Used
• Available objects such as a duster, pen, notebook, first aid box etc.
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• Burns are caused by coming in contact with hot objects accidentally. Burns can be minor or major.
• You can get an electric shock if current passes through your body or hair. When a person gets a severe
shock his or her skin turns white or pale blue. The first aid has to be given to the victim
Demonstrate
First aid steps
For Minor Burns
STEP 1: Pour cold water on the burnt area.
STEP 2: Apply a paste of baking soda and water or use a wet compress of baking soda solution in
water.
STEP 3: Cover the burnt area with a thin cloth to keep it free of dust.
74
Welding and Quality
Technician
STEP 2: Do not wrap any blanket around him because that will raise the temperature of the burnt
area.
STEP 3: Call the doctor immediately.
STEP 4: Till the time the doctor arrives, make the victim to lie down in a quiet place but keep the
feet slightly raised.
Activity
• Conduct a skill practice activity.
• Ask the students to assemble together.
• Explain the purpose and duration of the activity.
• Set guidelines pertaining to discipline and expected tasks.
Do
• Ask them to get into pairs for practice.
• Go around and make sure they are doing it properly.
• Wrap the unit up after summarizing the key points and answering questions.
75
Facilitator Guide
76
Welding and Quality
Technician
UNIT 4.5: 5S
Unit Objectives
At the end of this unit, students will be able to:
1. Explain importance of 5S;
2. Describe 5S activities.
Resources to be Used
• Available objects such as white board, marker pens, duster, participant manual etc.
• PC with LCD Projector or Flip Chart
Do
• Greet and welcome the participants to the next session of the program.
• Before starting the session ask them do they have any doubts pertaining to the previous unit.
Say
• 5S is designed as a visually-oriented system of cleanliness, organization and arrangement.
Elaborate
5S Approach: 5S is created by a list of five Japanese words: seiri, seiton, seiso, seiketsu, and shitsuke.
5S system is implemented for organizing the workplace for increasing effectiveness and efficiency by
maintaining the area and items, storing the items used, and sustaining the new practices.
Benefits of 5S are:
• Cleaner and safety work
• Reduced waste of time through more workplace organization
77
Facilitator Guide
• Organised space
• Improved self-discipline
• Improved workplace culture
5S consist of:
• Sorting - Sorting and separating tools removes unnecessary items from the work area and keep
the place clean.
• Simplifying - Tools kept at the appropriate storage area are clean and ready to use.
• Systematic Cleaning - Organized daily cleaning and inspection of the workplace.
• Standardizing - Standardizing makes unusual and out-of-the-ordinary conditions noticeable.
• Sustaining - It is aimed to maintain the improvements from the other 5S activities.
Phases of 5S:
78
Welding and Quality
Technician
Measuring the 5S Level of Achievement: Check the level of 5S from I to V for Simplifying.
79
Facilitator Guide
Ask
• You could ask the objectives and advantages of 5S
• You could ask the 5 levels of checking 5S
Activity
• Conduct a skill practice activity.
• Ask the students to assemble together.
• Do the 5S audit of your training center and check the level of center
Field Visit
You could visit any of the industry and show the firefighting equipment. With the help of field visit you
could show the where we need to fit various firefighting equipment and its role.
80
5. Welding Operation
Unit 5.1 – Types of Weld - Fillet and Groove
Unit 5.2 – Types of Joints
Unit 5.3 – Welding Positions
Unit 5.4 – Material Preparation
Unit 5.5 – Edge Preparation
Unit 5.6 – Fit Up
Unit 5.7 – Welding Demonstration
Unit 5.8 – Welding Practice
ASC/N3104
ASC/N3105
Facilitator Guide
82
Welding and Quality
Technician
Unit Objectives
At the end of this unit, you will be able to:
1. Identify the different types of weld;
2. List the different parts of weld.
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster.
• PC with LCD Projector or Flip Chart
• Participant Manual
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• Welds can be broadly classified into fillet and groove weld
• A fillet weld is the one in which the weld beads are deposited on the edge of the two surfaces to be
joined. These surfaces do not have any groove.
• Groove welds are welds made in the groove between two pieces to be joined.
• A single run of electrode on a metal during welding is called a pass. When the base metal pieces to be
welded are thick, then a single pass is not enough to fill the gap between the two pieces. Therefore
multiple passes are required.
Elaborate
Parts of Weld
• Base Metal: The metal pieces that are being welded are known as “base metal” or “work piece”
83
Facilitator Guide
• Root: The root is the point at which the backside of the weld intersects the base metal surface.
• Root Run: The first run deposited in the root of a joint is the root run.
• Root Gap: The distance between the parts to be joined is called the root gap.
• Toe: The point where the weld face and the base metal are connected is called the toe.
• Leg Length: The space between the junction of the metals and the point where the weld metal
connects the base metal is the leg length.
• Throat Thickness: The space between the junction of the metals and the midpoint of the line
connecting the two toes is called throat thickness.
• Heat Affected Zone: The heat affected zone is the place under the weld or around it which has
not welded but the heat of welding has changed its properties.
• Depth of Penetration: The depth a weld ranges into a joint from the metal surface is called the
depth of penetration.
• Weld Junction: The boundary between the fusion zone and the heat affected zone is the weld
junction.
• Weld Face: The surface of a weld as viewed from the side from which the weld was made is the
weld face.
84
Welding and Quality
Technician
• The Root Pass: The first weld run is known as Root Pass or Root Run.
• Hot Pass: The run above the root run is called hot pass.
• Filler Runs: All the runs above the hot pass, except the top ones are called filler runs.
• Cover Runs: The top layer runs are known as cover runs.
Ask
• You could ask about different types of weld.
• You could ask about multipass welding
85
Facilitator Guide
Unit Objectives
At the end of this unit, Students will be able to:
1. Identify the different types of joints.
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster, Participant Manual.
• PC with LCD Projector or Flip Chart
• Samples of different types of welding joints
Do
• Greet and welcome the participants to the next unit of the program.
Say
• There are five basic types of joints: corner joint, butt joint, lap joint, tee joint and edge joint.
86
Welding and Quality
Technician
Elaborate
Butt Joint: A joint between two members lying almost in the same plane.
Corner Joint: A joint between two members located almost at right angles to each other in the form of
an angle.
Edge Joint: A joint between two edge of two or more parallel or almost parallel members.
Tee Joint: A joint between two members located almost at right angles to each other in the form of a T.
Do
• Explain different types of joints.
87
Facilitator Guide
Unit Objectives
At the end of this unit, you will be able to:
1. Describe the different welding positions;
2. State the norms of position classification
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster, Participant Manual.
• PC with LCD Projector or Flip Chart
Do
• Greet and welcome the participants to the next unit of the program.
Say
• Generally welding is done in four positions
88
Welding and Quality
Technician
Elaborate
The position classification for welding is done as per following rules:
• If the position is flat or down hand it is numbered 1
• If the position is horizontal the number given is 2.
• If the position is vertical the nomenclature given is 3.
• If the position is overhead the nomenclature is given as 4.
Type of Weld
• If the weld is fillet type it is named F.
• If the weld is groove type it is named G.
89
Facilitator Guide
Plate Positions
90
Welding and Quality
Technician
91
Facilitator Guide
92
Welding and Quality
Technician
93
Facilitator Guide
Other Symbols
94
Welding and Quality
Technician
Do
• Explain different welding positions.
95
Facilitator Guide
Unit Objectives
At the end of this unit, you will be able to:
1. Define material preparation;
2. Describe the different methods of cleaning and cutting metals.
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster, Participant manual.
• PC with LCD Projector or Flip chart
Do
• Greet and welcome the participants to the next unit of the program.
Say
• Before welding, the raw material is in the form of metal sheets or blocks and needs to undergo
material preparation process.
• To make components of different sizes and shapes, material need to be cut and cleaned from the raw
sheets or blocks. This process of cutting and cleaning is known as material preparation.
• There are different methods of cutting metal:
o Cold Cutting
– Chisel
– Hacksaw
– Shearing
o Gas Cutting
– Pug Cutting
o Plasma Cutting
• Any material must be free of any foreign material like oil, paint, rust, moisture, scale etc before it
96
Welding and Quality
Technician
can be welded. If these impurities are not removed, the weld will have defects and the weld may be
porous, brittle or weak. Material cleaning is done by different methods depending on the material
and the type of impurity. Cleaning can be done by:
o Wire Brushing
o Grinding
o Rubbing with Emery Paper
o Flaming
o Chemical Cleaning
Do
• Ask about their understanding about the raw material cutting and cleaning for welding.
• Show them the material cutting and cleaning processes follow in industry.
97
Facilitator Guide
Unit Objectives
At the end of this unit, you will be able to:
1. Explain edge preparation;
2. State the methods of edge preparation;
3. List the types of edges.
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster, Participant manual.
• PC with LCD Projector or Flip chart
Do
• Greet and welcome the participants to the next unit of the program.
Say
• Edges of the metal pieces have to be shaped and prepared for welding. This is known as edge
preparation.
• There are many methods of edge preparation i.e. grinding, filing, milling, gas cutting etc.
• There are various types of possible edges i.e. square edge, bevel edge, double bevel edge etc. Type of
edge is determined by the drawing of joint.
Elaborate
There are many methods of edge preparation. The method that is chosen will depend on:
• The shape of the edge to be prepared
• The thickness of the metal to be welded
98
Welding and Quality
Technician
Types of Edges
The choice of edge depends on:
• the thickness of the metal
• the type of joint and
• the type of weld
• requirement of welding strength
The most common types of edge preparation are:
99
Facilitator Guide
Do
• Ask about their understanding about the edge preparation and methods of edge preparation.
100
Welding and Quality
Technician
Unit Objectives
At the end of this unit, you will be able to:
1. Understand purpose and method of fit up;
2. To form the component as per the drawing.
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster, Participant manual.
• PC with LCD Projector or Flip chart
• Workpiece, bend rod and welding setup
Do
• Greet and welcome the participants to the next unit of the program.
Say
• A proper fit up is important if a good weld is to be made.
• Every fit up has edge preparation:
o The joint is brought to the required shape and dimension as per the drawing
o Avoids disturbance of alignment of the joint during welding
Demonstrate
Steps for Actual Fit Up
Step 1: To arrange the components that we need.
Step 2:
• Components are kept side by side on a levelled surface.
101
Facilitator Guide
Activity
• Conduct a skill practice activity.
• Ask the students to assemble together.
• Explain the purpose and duration of the activity.
• Set guidelines pertaining to discipline and expected tasks.
Do
• Divide the class into pairs.
• Go around and make sure they are doing it properly.
102
Welding and Quality
Technician
Unit Objectives
At the end of this unit, you will be able to:
1. Run a bead along a pre-defined path in different positions in different modes of transfer.
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Welding tools and equipment
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• In this session we are going to run welding beads on workpiece in different positions and metal
transfer modes.
• We will learn about different parameters settings need to done during the welding of different size
workpiece.
103
Facilitator Guide
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Mild Steel Plate
• MIG wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Carbon dioxide (CO2)
• Regulator
• Flow meter
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
104
Welding and Quality
Technician
Say
For short circuit mode of transfer parameters are:
Voltage 20 volts
Gas flow rate 16 litres /minute
Stick-out 12 to 15 mm
Welding /Travel speed 250 mm/min
Joint position 1F
Torch (angle and technique) Push or Pull technique
Torch weaving Yes/No
Base material 3 mm MS Plate
Demonstrate
Procedure to Run a Bead
1. Wear the PPE.
2. Set the machine for striking a GMAW arc.
3. Set up the parameters for laying a bead in 1F position.
4. Take a level plate and place it in down hand 1F position.
5. Draw a straight line using a chalk and a scale.
6. Strike an arc from one end of the straight line and start a running bead.
7. Complete the running bead till you reach the end of the straight line.
8. Release the torch switch to bring all functions to a stop.
105
Facilitator Guide
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Mild Steel Plate
• MIG wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Carbon dioxide (CO2)
• Regulator
• Flow meter
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
For globular mode of transfer parameters are:
Voltage 25 volts
Gas flow rate 16 litres /minute
106
Welding and Quality
Technician
Stick-out 12 to 15 mm
Welding /Travel speed 250 - 300 mm/min
Joint position 1F
Torch (angle and technique) Push or Pull technique
Torch weaving Yes/No
Wire consumable ER 70S6 diameter 1.2 mm
Base material 3 mm MS Plate
Demonstrate
Procedure to Run a Bead
1. Wear the PPE.
2. Set the machine for striking a GMAW arc.
3. Set up the parameters for laying a bead in 1F position.
4. Take a level plate and place it in down hand 1F position.
5. Draw a straight line using a chalk and a scale.
6. Strike an arc from one end of the straight line and start a running bead.
7. Complete the running bead till you reach the end of the straight line.
8. Release the torch switch to bring all functions to a stop.
107
Facilitator Guide
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Mild Steel Plate
• MIG wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Argon CO2 mixed gas
• Regulator
• Flow meter
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
For globular mode of transfer parameters are:
Filler wire 1.2 mm
Gas 80/20, Argon CO2 mixed gas
Current 260 amps
Wire feed speed 260 inches/min (6.6 meters)
Voltage 27 volts
Gas flow rate 16 litres /minute
108
Welding and Quality
Technician
Stick-out 15 to 18 mm
Welding /Travel speed 250 - 300 mm/min
Joint position 1F
Torch (angle and technique) Push or Pull technique
Torch weaving Yes/No
Wire consumable ER 70S6 diameter 1.2 mm
Base material 8 mm – 10 mm MS Plate
Demonstrate
Procedure to Run a Bead
1. Wear the PPE.
2. Set the machine for striking a GMAW arc.
3. Set up the parameters for laying a bead in 1F position.
4. Take a level plate and place it in down hand 1F position.
5. Draw a straight line using a chalk and a scale.
6. Strike an arc from one end of the straight line and start a running bead.
7. Complete the running bead till you reach the end of the straight line.
8. Release the torch switch to bring all functions to a stop.
109
Facilitator Guide
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Mild Steel Plate
• MIG filler wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Argon CO2 mixed gas
• Regulator
• Flow meter
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
For spray transfer mode parameters are:
110
Welding and Quality
Technician
Joint position 2F
Torch (angle and technique) Push or Pull technique
Torch weaving Yes/No
Wire consumable ER 70S6 diameter 1.2 mm
Base material 8 mm – 10 mm MS Plate
Demonstrate
Procedure to Run a Bead
1. Wear the PPE.
2. Set the machine for striking a GMAW arc.
3. Set the parameters for striking a GMAW arc in 2F position.
4. Using a chalk, draw a line parallel to the length of a plate at 25 mm from the sides.
5. Place another plate vertically on the line so drawn to form a ‘T’. Hold the plate.
6. Tack the plate which is formed as a ‘T’ at one corner that is at the start and remove your hand.
7. Use a try square to ensure 90 degree position. Run the try square through the length of the joint
to ensure the verticality.
8. Tack the plate which is formed as a ‘T’ at the end of the joint.
9. Now the fit up is ready to do the fillet weld in 2F position.
10. Place the fit up plate on a table in 2F position.
11. Orient the torch at 45 degrees focusing on the root. The aim is to do the welding by fusing the
root using push technique.
12. Start the welding.
13. Complete the running bead till you reach the end of the plate.
14. Check penetration by macro section.
111
Facilitator Guide
112
Welding and Quality
Technician
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Mild Steel Plate
• MIG wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Carbon dioxide (CO2)
• Regulator
• Flow meter
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
For spray transfer mode parameters are:
Filler wire 0.8 mm
Gas CO2
Current 160 amps
113
Facilitator Guide
Voltage 20 volts
Gas flow rate 16 litres /minute
Stick-out 12 to 15 mm
Welding /Travel speed 250 mm/min
Joint position 1F
Torch (angle and technique) Push or Pull technique
Torch weaving Yes/No
Wire consumable ER 70S6 diameter 1.2 mm
Base material 3 mm MS Plate
Tips
• The width of the running bead on both runs should be uniform from start to finish. This signifies that
your hand is steady.
• The 2nd run should be absolutely parallel to the first run. This signifies that you are able to bring out
the output exactly the way you visualised.
• The height or reinforcement of the bead should be uniform from start to finish. This signifies good
hand-eye coordination and synchronisation of feeding of filler material.
Demonstrate
Procedure to run a parallel bead in 1F position
1. Wear the PPE.
2. Set the machine for striking a GMAW arc.
3. Set up the parameters for striking a GMAW arc.
4. Take a level plate and place it in down hand 1F position.
5. Draw a straight line using a chalk and a scale.
6. Strike an arc from one end of the straight line and start a running bead.
7. Complete the running bead till you reach the end of the straight line.
114
Welding and Quality
Technician
115
Facilitator Guide
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Mild Steel Plate
• MIG wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Carbon dioxide (CO2)
• Regulator
• Flow meter
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Elaborate
Weld is classified into Fillet Weld and Groove Weld.
• Face: The face represents the insides of the weld. If the face is good, the weld can be expected to
be sound.
• Toe: Toe of the weld takes the entire load of the weld. A well done toe doesn’t have any undercuts.
• Throat: The throat, also called penetration, is normally defined by the leg length.
116
Welding and Quality
Technician
• Reinforcement: The height to which the bead is protruding from the surface of the plate is the
reinforcement.
• Leg Length: The distance from the root to the toe of the fillet weld. Leg length determines the size
of fillet weld. The leg length should be uniform.
Say
For short circuit mode of transfer parameters are:
Filler wire 0.8 mm
Gas CO2
Current 160 amps
Wire feed speed 320 inches/min (8.13 meters)
Voltage 20 volts
Gas flow rate 16 litres /minute
Stick-out 12 to 15 mm
Welding /Travel speed 250 mm/min
Joint position 1F
Torch (angle and technique) Push or Pull technique
Torch weaving Yes/No
Wire consumable ER 70S6 diameter 1.2 mm
Base material 3 mm MS Plate
Tips
• The merged pad should have a uniform height of deposit of weld metal.
• There should not be any deep grooves. To find this out, run a sharp tool on the beads. If the tool is
stuck in the beads, it means the groove is deep, which is not preferable.
• Voids are under filled pockets. There should not be any voids.
117
Facilitator Guide
Demonstrate
Procedure to merge a bead is
1. Wear the PPE.
2. Set the machine for striking a GMAW arc.
3. Set up the parameters for laying a bead in 1F position.
4. Take a level plate and place it in downhand 1F position.
5. Draw a straight line using a chalk and a scale.
6. Strike an arc from one end of the straight line and start a running bead.
7. Complete the running bead till you reach the end of the straight line.
8. Release the torch switch to bring all functions to a stop.
9. Start the second run. Focus the arc on the toe of the 1st run. Form a bead in such a way that 50%
of it is over the 1st bead and rest 50% is on the base plate.
10. Continue in the same way till you complete the pad of defined size.
118
Welding and Quality
Technician
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Mild Steel Plates (2 numbers)
• MS rod
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Carbon dioxide (CO2)
• Regulator
• Flow meter
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
For short circuit mode of transfer parameters are:
119
Facilitator Guide
Joint position 1G
Torch (angle and technique) Push or Pull technique
Torch weaving Yes/No
Wire consumable ER 70S6 diameter 1.2 mm
Base material 3 mm MS Plate
Demonstrate
Procedure to run a bead is
1. Wear the PPE.
2. Set the machine for striking a GMAW arc.
3. Place both the plates on a levelled surface in the down hand – 1G position.
4. Check the level of the plate using a try square.
5. Keep a gap of 2 mm at the start and 3.15 mm at the finish between the two plates. Ensure the
same by inserting the correct size rods at the respective ends.
6. Tack weld at the start, middle and the end while maintaining a gap of 2 mm at start and 3.15 mm
at the finishing end.
7. Remove the rods and start welding from the start point to the finish point using keyhole technique.
120
Welding and Quality
Technician
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Mild Steel Plate
• MIG filler wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Gas cylinder
• Regulator
• Flow meter
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
For short circuit mode of transfer parameters are:
121
Facilitator Guide
Voltage 20 volts
Gas flow rate 16 litres /minute
Stick-out 12 to 15 mm
Welding /Travel speed 250 mm/min
Demonstrate
Procedure to Lap Joint on 3 mm Plate in Inclined Position
1. The procedure for making this weld is similar to that used for making fillet welds in T joints.
2. The electrode should be held to form an angle approximately 30° from the vertical and tilted 15°
in the direction of welding.
3. The position of the electrode in relation to the plates is shown in the given figure.
4. The aim is to do the welding by using push or pull technique.
5. Start the welding.
6. Complete the running bead till you reach the end of the plate.
7. Repeat the same exercise by keeping the plates in an inclined position.
122
Welding and Quality
Technician
Unit Objectives
At the end of this unit, you will be able to:
1. Practice running a bead in different positions in different modes of transfer.
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Welding tools and equipment
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• In this session we are going to do practice of running welding beads on workpiece in different positions
and metal transfer modes.
• We will practice different parameters settings need to done during the welding of different size
workpiece.
123
Facilitator Guide
Resources to be Used
• Available objects such as pen, notebook,
• Mild Steel Plate
• MIG wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Shielding gas
• Regulator
• Flow meter
• Personal Protective Equipment
Practical
• Group the participants for the activity.
• Explain the purpose and duration of the activity.
• Activities they have to perform are:
o Practice to run a bead on plate in 1F position in short circuit mode of transfer;
o Practice to run a parallel bead on plate in 1F position in short circuit mode of transfer;
o Practice to merge a bead on plate in 1F position in short circuit mode of transfer;
o Practice to lay a root run on plate in 1F position in short circuit mode of transfer.
124
Welding and Quality
Technician
Say
• Today they are going to perform the practical.
• They have to run a bead on plate in 1F position in short circuit mode of transfer.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for short circuit mode of transfer
• Now they have to start the welding procedure on workpiece.
• They have to move the torch from right to left i.e. they should use the leftward technique/forward
technique/push technique along the chalk line to form a continuous, smooth, reinforced, liquid bead
of uniform height and width exhibiting a smooth ripple.
• They have to complete atleast 25 meters on workpiece.
Resources to be Used
• Group the participants for the activity.
• Explain the purpose and duration of the activity.
• Activities they have to perform are:
o Practice to run a bead on plate in 1F position in short circuit mode of transfer;
o Practice to run a parallel bead on plate in 1F position in short circuit mode of transfer;
o Practice to merge a bead on plate in 1F position in short circuit mode of transfer;
o Practice to lay a root run on plate in 1F position in short circuit mode of transfer.
125
Facilitator Guide
• The participant themselves should be conditioned to consider these minute details and make sure
everything is in place.
• Trainer has to evaluate the trainee work on following parameters and format:
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
126
Welding and Quality
Technician
Say
• Now they have to perform another welding activity.
• They have to run a parallel bead on plate in 1F position in short circuit mode of transfer.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for short circuit mode of transfer
• Now they have to start the welding procedure on workpiece.
• They have to move the torch along the chalk line using the push technique to form a continuous,
smooth, reinforced, liquid bead of uniform height and width exhibiting a smooth ripple.
• The beads need to be laid keeping a spacing of 5 to 10 mm in such a way that the second bead shall
run parallel to the first one.
• They have to complete atleast 25 meters on workpiece.
127
Facilitator Guide
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
128
Welding and Quality
Technician
Say
• Now they have to perform another welding activity.
• They have to merge a bead on plate in 1F position in short circuit mode of transfer.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for short circuit mode of transfer
• Now they have to start the welding procedure on workpiece.
• They have to use push technique along the chalk line to form a continuous, smooth, reinforced, liquid
bead of uniform height and width exhibiting a smooth ripple. They should focus on the toe of the first
bead to have a smooth overlap/merging of bead.
• They have to complete atleast 25 meters on workpiece.
129
Facilitator Guide
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
130
Welding and Quality
Technician
Say
• Now they have to perform another welding activity.
• They have to root run a bead in 1F position in short circuit mode of transfer.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for short circuit mode of transfer
• Now they have to start the welding procedure on workpiece.
• They have to make the fit-up which consists of the following procedure:
I. Take the two base plates.
II. Have a gap of 2.5 mm at the start and 3.15 mm at the end by inserting suitable inserts.
III. Make a bridge using the filler material at the start and at the end between the two individual
plates to be joined.
IV. Place a bridge after every inch so that the plate remains in position for the activity to be performed.
• Follow keyhole technique to lay a running bead using filler material to have a full penetration weld.
• They have to complete atleast 25 meters on workpiece.
131
Facilitator Guide
Fit-up
1 and more inconsistencies 0
No inconsistencies 2
Uniform root bead ensuring full penetration. No visible edges of the individual plates to be sighted
from beneath after welding.
2 and more inconsistencies 0
1 inconsistency 1
Full penetration 2
Uniformity of the width and the height of the bead along the run
More than 2 inconsistencies 0
0-2 inconsistencies 1
No inconsistencies 2
Defects: Undercut and overlap for each line
0 defects 2
Up to 2 defects 1
More than 2 0
Total 10
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
132
Welding and Quality
Technician
Resources to be Used
• Available objects such as pen, notebook,
• Mild Steel Plate
• MIG wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Shielding gas
• Regulator
• Flow meter
• Personal Protective Equipment
Practical
• Group the participants for the activity.
• Explain the purpose and duration of the activity.
• Activities they have to perform are:
o Practice to run a bead on plate in 1G position in short circuit mode of transfer;
o Practice to run a parallel bead on plate in 1G position in short circuit mode of transfer;
o Practice to merge a bead on plate in 1G position in short circuit mode of transfer;
o Practice to lay a root run on plate in 1G position in short circuit mode of transfer.
133
Facilitator Guide
Say
• Today they are going to perform the practical.
• They have to run a bead on plate in 1G position in short circuit mode of transfer.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for short circuit mode of transfer
• Now they have to start the welding procedure on workpiece.
• They have to move the torch from right to left i.e. they should use the leftward technique/forward
technique/push technique along the chalk line to form a continuous, smooth, reinforced, liquid bead
of uniform height and width exhibiting a smooth ripple.
• They have to complete atleast 25 meters on workpiece.
134
Welding and Quality
Technician
Not uniform 0
Stops and restart quality for each line
0-1 stop and restart (smooth finish) 2
2 or 3 stops and restart (smooth finish) 1
More than 3 stops and restarts 0
Defects: Undercut and overlap for each line
Up to 2 defects 2
3 or 4 defects 1
More than 4 0
Total 10
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
135
Facilitator Guide
Say
• Now they have to perform another welding activity.
• They have to run a parallel bead on plate in 1G position in short circuit mode of transfer.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for short circuit mode of transfer
• Now they have to start the welding procedure on workpiece.
• They have to move the torch along the chalk line using the push technique to form a continuous,
smooth, reinforced, liquid bead of uniform height and width exhibiting a smooth ripple.
• The beads need to be laid keeping a spacing of 5 to 10 mm in such a way that the second bead shall
run parallel to the first one.
• They have to complete atleast 25 meters on workpiece.
136
Welding and Quality
Technician
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
137
Facilitator Guide
Say
• Now they have to perform another welding activity.
• They have to merge a bead on plate in 1G position in short circuit mode of transfer.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for short circuit mode of transfer
• Now they have to start the welding procedure on workpiece.
• They have to use push technique along the chalk line to form a continuous, smooth, reinforced, liquid
bead of uniform height and width exhibiting a smooth ripple. They should focus on the toe of the first
bead to have a smooth overlap/merging of bead.
• They have to complete atleast 25 meters on workpiece.
138
Welding and Quality
Technician
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
139
Facilitator Guide
Say
• Now they have to perform another welding activity.
• They have to root run a bead in 1G position in short circuit mode of transfer.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for short circuit mode of transfer
• Now they have to start the welding procedure on workpiece.
• They have to make the fit-up which consists of the following procedure:
I. Take the two base plates.
II. Have a gap of 2.5 mm at the start and 3.15 mm at the end by inserting suitable inserts.
III. Make a bridge using the filler material at the start and at the end between the two individual
plates to be joined.
IV. Place a bridge after every inch so that the plate remains in position for the activity to be performed.
• Follow keyhole technique to lay a running bead using filler material to have a full penetration weld.
• They have to complete atleast 25 meters on workpiece.
140
Welding and Quality
Technician
Fit-up
1 and more inconsistencies 0
No inconsistencies 2
Uniform root bead ensuring full penetration. No visible edges of the individual plates to be sighted
from beneath after welding.
2 and more inconsistencies 0
1 inconsistency 1
Full penetration 2
Uniformity of the width and the height of the bead along the run
More than 2 inconsistencies 0
0-2 inconsistencies 1
No inconsistencies 2
Defects: Undercut and overlap for each line
0 defects 2
Up to 2 defects 1
More than 2 0
Total 10
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
141
Facilitator Guide
Resources to be Used
• Available objects such as pen, notebook,
• Mild Steel Plate
• MIG wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Shielding gas
• Regulator
• Flow meter
• Personal Protective Equipment
Practical
• Group the participants for the activity.
• Explain the purpose and duration of the activity.
• Activities they have to perform are:
o Practice lap joint on 3 mm plate in inclined position using open arc, 0.8 mm wire and CO2.
142
Welding and Quality
Technician
Say
• Today they are going to perform the practical.
• They have to make lap joint on 3 mm plate in inclined position using open arc, 0.8 mm wire and CO2.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for short circuit mode of transfer
• Now they have to start the welding procedure on workpiece.
• They have to make the fit-up which consists of the following procedure:
I. Take the two base plates.
II. Have a gap of 2.5 mm at the start and 3.15 mm at the end by inserting suitable inserts.
III. Make a bridge using the filler material at the start and at the end between the two individual
plates to be joined.
IV. Place a bridge after every inch so that the plate remains in position for the activity to be performed.
• Follow keyhole technique to lay a running bead using filler material to have a full penetration weld.
• They have to complete atleast 25 meters on workpiece.
143
Facilitator Guide
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
144
Welding and Quality
Technician
Resources to be Used
• Available objects such as pen, notebook,
• Mild Steel Plate
• MIG wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Shielding gas
• Regulator
• Flow meter
• Personal Protective Equipment
Practical
• Group the participants for the activity.
• Activities they have to perform are:
o Practice to run a bead on plate in 1G position in spray transfer mode;
o Practice to run a parallel bead on plate in 1G position in spray transfer mode;
o Practice to merge a bead on plate in 1G position in spray transfer mode;
o Practice to lay a root run on plate in 1G position in spray transfer mode.
145
Facilitator Guide
Say
• Today they are going to perform the practical.
• They have to run a bead on plate in 1G position in spray transfer mode.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for spray transfer mode
• Now they have to start the welding procedure on workpiece.
• They have to move the torch from right to left i.e. they should use the leftward technique/forward
technique/push technique along the chalk line to form a continuous, smooth, reinforced, liquid bead
of uniform height and width exhibiting a smooth ripple.
• They have to complete atleast 25 meters on workpiece.
146
Welding and Quality
Technician
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
147
Facilitator Guide
Say
• Now they have to perform another welding activity.
• They have to run a parallel bead on plate in 1G position in spray transfer mode.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for spray transfer mode
• Now they have to start the welding procedure on workpiece.
• They have to move the torch along the chalk line using the push technique to form a continuous,
smooth, reinforced, liquid bead of uniform height and width exhibiting a smooth ripple.
• The beads need to be laid keeping a spacing of 5 to 10 mm in such a way that the second bead shall
run parallel to the first one.
• They have to complete atleast 25 meters on workpiece.
148
Welding and Quality
Technician
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
149
Facilitator Guide
Say
• Now they have to perform another welding activity.
• They have to merge a bead on plate in 1G position in spray transfer mode.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for spray transfer mode
• Now they have to start the welding procedure on workpiece.
• They have to use push technique along the chalk line to form a continuous, smooth, reinforced, liquid
bead of uniform height and width exhibiting a smooth ripple. They should focus on the toe of the first
bead to have a smooth overlap/merging of bead.
• They have to complete atleast 25 meters on workpiece.
150
Welding and Quality
Technician
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
151
Facilitator Guide
Say
• Now they have to perform another welding activity.
• They have to root run a bead in 1G position in spray transfer mode.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for spray transfer mode
• Now they have to start the welding procedure on workpiece.
• They have to make the fit-up which consists of the following procedure:
I. Take the two base plates.
II. Have a gap of 2.5 mm at the start and 3.15 mm at the end by inserting suitable inserts.
III. Make a bridge using the filler material at the start and at the end between the two individual
plates to be joined.
IV. Place a bridge after every inch so that the plate remains in position for the activity to be performed.
• Follow keyhole technique to lay a running bead using filler material to have a full penetration weld.
• They have to complete atleast 25 meters on workpiece.
152
Welding and Quality
Technician
Fit-up
1 and more inconsistencies 0
No inconsistencies 2
Uniform root bead ensuring full penetration. No visible edges of the individual plates to be sighted
from beneath after welding.
2 and more inconsistencies 0
1 inconsistency 1
Full penetration 2
Uniformity of the width and the height of the bead along the run
More than 2 inconsistencies 0
0-2 inconsistencies 1
No inconsistencies 2
Defects: Undercut and overlap for each line
0 defects 2
Up to 2 defects 1
More than 2 0
Total 10
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
153
Facilitator Guide
Resources to be Used
• Available objects such as pen, notebook,
• Mild Steel Plate
• MIG wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Shielding gas
• Regulator
• Flow meter
• Personal Protective Equipment
Practical
• Group the participants for the activity.
• Explain the purpose and duration of the activity.
• Activities they have to perform are:
o Practice fillet weld on 8 mm plate in 2F position using 1.2 mm wire using spray transfer mode.
154
Welding and Quality
Technician
Say
• Today they are going to perform the practical.
• They have to make fillet weld on 8 mm plate in 2F position using 1.2 mm wire using spray transfer
mode.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for spray transfer mode
• Now they have to start the welding procedure on workpiece.
• They have to follow the following procedure:
1. Striking the GMAW arc.
2. Preparation of the fit up.
i. Take a base plate of size 8 mm and draw a line in the centre.
ii. Take the other base plate and place it vertically over the line ensuring the perpendicular
position.
iii. Hold it in the above position and place a tack weld at the intersection at one end of the plate
and run a tri-square to ensure the perpendicular position. Ensure no gap between the two
plates.
iv. Place a tack weld on the other end of the plate intersection.
3. Place the plate in 2F position - horizontal position.
4. Locate the torch so that it focuses the root of the T joint making an angle of 45 degrees either to the
base plate or the vertical plate.
5. Orient the torch at 45 degrees focusing on the root. The aim is to do the welding by fusing the
root using the leftward technique, forward technique or push technique. Alignment of the torch is
complete.
6. Strike a GMAW arc and form weld bead so that it has equal leg length and progress the bead all
through the length of the joint.
7. Check penetration by macro section.
155
Facilitator Guide
• The participant themselves should be conditioned to consider these minute details and make sure
everything is in place.
• Trainer has to evaluate the trainee work on following parameters and format:
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
156
Welding and Quality
Technician
Resources to be Used
• Available objects such as pen, notebook,
• Mild Steel Plate
• MIG wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Shielding gas
• Regulator
• Flow meter
• Personal Protective Equipment
Practical
• Group the participants for the activity.
• Explain the purpose and duration of the activity.
• Activities they have to perform are:
o Practice lap joints on 3 mm plate in inclined position using an open arc, 0.8 mm wire and CO2
using short circuit mode of transfer;
o Prepare a square butt joint on 3 mm sheet using short circuit mode of transfer with 0.8 mm wire
and CO2.
157
Facilitator Guide
Say
• Today they are going to perform the practical.
• They have to make lap joints on 3 mm plate in inclined position using an open arc, 0.8 mm wire and
CO2 using short circuit mode of transfer.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for short circuit mode of transfer
• Now they have to start the welding procedure on workpiece.
• They have to follow the following procedure:
1. Striking the GMAW arc.
2. Preparation of the fit up.
3. Place the plate in inclined position.
4. Locate the torch so that it focuses the root of the joint making an angle of 30 degrees from the
vertical and tilted 15 degrees in the direction of welding. The aim is to do the welding by fusing
the root using the push or pull technique.
5. Strike an arc and form weld bead so that it has equal leg length and progress the bead all through
the length of the joint.
158
Welding and Quality
Technician
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
159
Facilitator Guide
Say
• Today they are going to perform the practical.
• They have to make a square butt joint on 3 mm sheet using short circuit mode of transfer with 0.8 mm
wire and CO2.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for short circuit mode of transfer
• Now they have to start the welding procedure on workpiece.
160
Welding and Quality
Technician
Uniformity of the width and the height of the bead along the run
More than 2 inconsistencies 0
0-2 inconsistencies 1
No inconsistencies 2
Defects: Undercut and overlap for each line
0 defects 2
Up to 2 defects 1
More than 2 0
Total 10
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
161
Facilitator Guide
Resources to be Used
• Available objects such as pen, notebook,
• Mild Steel Plate
• MIG wire
• Chipping hammer
• Work table connected to earth
• Bucket of water
• Ruler
• Complete MIG welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Shielding gas
• Regulator
• Flow meter
• Personal Protective Equipment
Practical
• Group the participants for the activity.
• Explain the purpose and duration of the activity.
• Activities they have to perform are:
o Practice fillet weld on 8 mm plate in 2F position using 1.2 mm wire with spray transfer mode.
162
Welding and Quality
Technician
Say
• Today they are going to perform the practical.
• They have to make fillet weld on 8 mm plate in 2F position using 1.2 mm wire using spray transfer
mode.
• First they have to make the notes in their notebook:
o Material required
o Procedure
o Parameters for spray transfer mode
• Now they have to start the welding procedure on workpiece.
• They have to follow the following procedure:
1. Striking the GMAW arc.
2. Preparation of the fit up.
i. Take a base plate of size 8 mm and draw a line in the centre.
ii. Take the other base plate and place it vertically over the line ensuring the perpendicular
position.
iii. Hold it in the above position and place a tack weld at the intersection at one end of the plate
and run a tri-square to ensure the perpendicular position. Ensure no gap between the two
plates.
iv. Place a tack weld on the other end of the plate intersection.
3. Place the plate in 2F position - horizontal position.
4. Locate the torch so that it focuses the root of the T joint making an angle of 45 degrees either to the
base plate or the vertical plate.
5. Orient the torch at 45 degrees focusing on the root. The aim is to do the welding by fusing the
root using the leftward technique, forward technique or push technique. Alignment of the torch is
complete.
6. Strike a GMAW arc and form weld bead so that it has equal leg length and progress the bead all
through the length of the joint.
7. Check penetration by macro section.
163
Facilitator Guide
• Trainer has to evaluate the trainee work on following parameters and format:
Summarize
• Summarize the main points.
• Ask participants if they have any doubts.
164
6. Flux Cored Arc
Welding (FCAW)
Unit 6.1 – Principles of Flux Cored Arc Welding (FCAW)
ASC/N3104
Facilitator Guide
166
Welding and Quality
Technician
Unit Objectives
At the end of this unit, you will be able to:
1. Explain why FCAW;
2. List the materials required for FCAW;
3. Name the types of FCAW – filler wire;
4. List the process parameters for FCAW.
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster, Participant manual.
• PC with LCD Projector or Flip Chart
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• FCAW process is used for various reasons:
o For high strength requirement;
o High productivity;
o Better shielding - shielding provided by gas as well as slag;
o Suitable for varieties of materials;
o Can tolerate abuses - weld even on rusted plates;
o Hard surfacing applications.
• Material required for FCAW:
o Helmet with shaded glass;
o Gas cylinder;
167
Facilitator Guide
o Power source;
o Gas hoses;
o Continuous filler wire - flux cored wire;
o Gas;
o Interconnection cables;
o Torch;
o PPE;
o Welding cables;
o Wire feeder;
o Accessories.
• Different types of FCAW - filler wire are:
o Self shielding flux cored filler wire;
o Gas shielded flux cored filler wire;
o Hard surfacing flux cored filler wire either self shielding or gas shielding.
• Classification of filler wires: AWS classification – E70T1, E70T2, E71T1 etc.
• Process parameters of FCAW: Similar to globular transfer mode
Ask
• You could ask about FCAW process.
• You could ask about materials required for FCAW process.
• You could ask about different types of filler wire used in FCAW process.
• Ask about parameters setting in FACW process.
168
Welding and Quality
Technician
Unit Objectives
At the end of this unit, you will be able to:
1. Run a bead along a pre-defined path in different positions in different modes of transfer.
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Welding tools and equipment
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• In this session we are going to run FCAW weld beads on workpiece in different positions and metal
transfer modes.
• We will learn about different parameters settings need to done during the welding of different size
workpiece.
169
Facilitator Guide
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Mild steel plates of size 8 mm X 50 mm X 200 mm
• Flux cored filler wire of size 1.2 mm specification E 70 – T1
• MS rod of size 2.5 and 3.15 mm
• Chipping hammer
• Tri-square
• Table connected to the ground
• Bucket of water
• Chalk piece
• Ruler
• FCAW welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Gas cylinder
• Regulator
• Flow meter
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
Required parameters are:
170
Welding and Quality
Technician
Voltage 28 - 30 volts
Gas flow rate 16 – 18 litres /minute
Stick-out 22 to 25 mm
Welding /Travel speed 280 - 300 mm/min
Joint position 2G
Torch (angle and technique) Push or Pull technique
Torch weaving No
Wire consumable E 70 T-1 diameter 1.2 mm
Base material 8 mm MS Plate
Demonstrate
Procedure to do butt weld on 8 mm plate in 2G position
1. Wear the PPE.
2. Set the machine for striking a FCAW arc.
3. Set the parameters for striking a FCAW arc in 2G position.
4. Do a fit up in 2G position.
5. Maintain a gap of 2 mm at the start and 3.15 mm at the finish between the two plates, by inserting
the appropriate rods.
6. Tack weld at the start, middle and the end. Ensure that the gaps at the start and finishing end are
maintained.
7. Remove the rods and place the plate in the 2G position.
8. Start welding from the start point to the finish point using keyhole technique.
9. Check for full penetration.
171
Facilitator Guide
Resources to be Used
• Available objects such as a duster, pen, notebook,
• Mild steel plates of size 8 mm X 50 mm X 200 mm
• Flux cored filler wire of size 1.2 mm specification E 70 – T1
• MS rod of size 2.5 and 3.15 mm
• Chipping hammer
• Tri-square
• Table connected to the ground
• Bucket of water
• Chalk piece
• Ruler
• FCAW welding outfit
• Earth cable with clamp
• Helmet with shaded glass
• Gas cylinder
• Regulator
• Flow meter
• Personal Protective Equipment
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
172
Welding and Quality
Technician
Say
Required parameters are:
Voltage 28 - 30 volts
Gas flow rate 16 – 18 litres /minute
Stick-out 22 to 25 mm
Welding /Travel speed 280 - 300 mm/min
Joint position 2F
Torch (angle and technique) Push or Pull technique
Torch weaving No
Wire consumable E 70 T-1 diameter 1.2 mm
Base material 8 mm MS Plate
Demonstrate
Procedure to do fillet weld on 8 mm plate in 2F position
1. Wear the PPE.
2. Set the machine for striking a FCAW arc.
3. Set the parameters for striking a FCAW arc in 2F position.
4. Using a chalk, draw a line parallel to the length of a plate at 25 mm from the sides.
5. Place another plate vertically on the line so drawn to form a ‘T’. Hold the plate.
6. Tack the plate which is formed as a ‘T’ at one corner that is at the start and remove your hand.
7. Use a try square to ensure 90 degree position. Run the try square through the length of the joint
to ensure the verticality.
8. Tack the plate which is formed as a ‘T’ at the end of the joint.
9. Now the fit up is ready to do the fillet weld in 2F position.
10. Place the fit up plate on a table in 2F position.
11. Orient the torch at 45 degrees focusing on the root. The aim is to do the welding by fusing the
root using push technique.
12. Start the welding.
13. Complete the running bead till you reach the end of the plate.
173
Facilitator Guide
174
7. Gas Metal Arc Welding
(GMAW) – After Welding
Unit 7.1 – Defects: Definition, Causes and Remedy
Unit 7.2 – Methods of Inspection
ASC/N0007
ASC/N0008
Facilitator Guide
176
Welding and Quality
Technician
Unit Objectives
At the end of this unit, you will be able to:
1. List the common defects that occur during welding and their causes;
2. State the ways to prevent defects.
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster, Participant manual.
• PC with LCD Projector or Flip Chart
• Welding defects samples
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• A welding defect is a discontinuity which does not allow the finished joint to withstand or carry the
required load.
• All defects are discontinuities but all discontinuities shall not be defects.
• Common defects found in welding are undercut, overlap, slag inclusion, porosity etc.
Elaborate
A defective welded joint will have the following common defects
1. Undercut: A groove at the toe or at the root of the weld on the weld face is called an undercut.
The causes of undercut are:
• Excessive amperage - meaning too high current
177
Facilitator Guide
178
Welding and Quality
Technician
• Impurities on the surface of the base metal or too high travel speed.
Ways to prevent defect
• Dry the electrodes; reduce the arc length and remove all grease, dirt etc.
• Weld at slower speed to allow gases to escape
• Grinding down and re-welding.
5. Lack of Fusion: When the weld metal fails to blend completely with the base metal or a weld bead
before it, the defect is called lack of fusion or incomplete fusion.
The causes of lack of fusion are:
• Small electrodes used on thick and cold steel
• Not enough heat and so base metal does not melt properly
• Wrong electrode angle and weaving
• Travel speed is too high and there is no enough time for fusion
• Surface of metal not clean
Ways to prevent defect
• Use larger size electrodes, increase amperage, and follow correct welding techniques.
6. Incomplete Penetration: When the weld metal does not penetrate to the root of the joint it is called
incomplete penetration.
Causes of incomplete penetration are:
• Current being too low
• Not enough root gap
• Electrode size is too big
• Improper technique, keyhole technique not followed completely
Ways to prevent defect
• The joint preparation and design must be such that the groove can be reached. Increase the
current and select proper electrode size.
7. Excessive Penetration: When the weld metal melts through the base metal and hangs underneath
the weld, it is a defect and it is called excessive penetration.
The possible causes of excessive penetration are:
• Current being too high
• Electrode very big
• Incorrect travel speed
179
Facilitator Guide
180
Welding and Quality
Technician
11. Distortion: Distortion cannot be eliminated in any form of welding, though it can be controlled. If the
weld metal contracts during welding forcing the base metal to move, it is a defect called distortion.
Possible causes of distortion can be:
• Non uniform heating and cooling of the joint or
• Excessive heat input
• Incorrect welding technique and travel speed
Ways to prevent defect
• Avoid over welding - The bigger the weld, the greater the shrinkage.
• Use a clamp to hold base metal in position.
• Weld in small segments to distribute the heat uniformly over the plates.
12. Excessive Spatter: When there is a lot of scattering of molten metal particles that cool to solid form,
near the weld bead it is called excessive spatter.
Causes of excess spatter are:
• The amperage or current is too high for the electrode
• Arc length is too long or voltage is too high
• Low travel speed
• Too much heat – higher current
Ways to prevent defect
• Decrease amperage or select larger electrode and
• Reduce arc length or voltage.
13. Arc Strike: If the electrode joins the base metal off from the weld accidentally it is called arc striking.
Cause of arc strike:
• Due to operator error
Ways to prevent defect
• The operator has to be careful and not touch the electrode on the metal plate at unintended
places when the machine is on.
14. Tungsten Inclusion: Tungsten inclusion is a defect which is due to tungsten melting and contaminating
the base metal.
This occurs due to:
• Polarity change which leads to melting of the tungsten electrode
• Excessive current for the given diameter of the electrode
181
Facilitator Guide
Do
• Ask the causes and its remedies of the welding defects.
• Ask what defects are usually found along the toe of a weld?
• Show the welding defects samples
182
Welding and Quality
Technician
Unit Objectives
At the end of this unit, you will be able to:
1. Know the classification of inspection methods;
2. Learn about the methods of Non Destructive Examination (NDE).
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster, Participant manual.
• PC with LCD Projector or Flip Chart
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• Methods of inspection can be classified into destructive and non destructive examination.
• Destructive testing is carried out on test specimens or on a specimen taken as a representative of
several similar ones.
• Destructive tests are costlier because they damage or break the weld.
• Non destructive examination can be done by different methods depending on the requirement.
• In non–destructive testing the weld is not broken or damaged and is therefore a cheaper method of
testing.
• Non destructive examination methods are visual examination, dye penetrant test, ultrasonic test and
X-Ray test.
183
Facilitator Guide
Elaborate
Methods of non-destructive examination
1. Visual Inspection: In visual inspection the finished weld should be examined for defects such as
undercut, overlap, surface irregularities, cracks, porosity and spatter.
2. Dye Penetrant Test: In dye penetrant test the weld is inspected for cracks, porosity or any other
surface defect.
3. Ultrasonic Test: Ultrasonic inspection is used to detect and locate internal defects such as cracks,
porosity, inclusions, lack of fusion and incomplete penetration. Wall thickness can be measured
in close vessels or in cases where such measurement cannot otherwise be made.
4. X-ray Test: X-rays are used to view a cross sectional area of a weld and locate defects. This process
is called radiography. Radiographs are used to assess the quality of welded joints
Do
• Ask the defects inspection process.
• Ask methods of defects inspection.
• Demonstrate the non-destructive examination methods
184
8. Inspect and Maintain
Product Quality
Unit 8.1 – Introduction to Quality Control
Unit 8.2 – Inspections
Unit 8.3 – Inspections of the final product
Unit 8.4 – CAPA and its implementation
Unit 8.5 – PPAP - PSW
Unit 8.6 – ISO/TS 16949
Unit 8.7 – 8ds
Unit 8.8 – FMEA
Unit 8.9 – The 5 Whys
ASC/N6301
Facilitator Guide
186
Welding and Quality
Technician
Unit Objectives
At the end of this unit, Students will be able to:
1. Understand Quality Control & Pre-delivery (PDI)
2. Understand the importance of Pre-delivery (PDI)
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster.
• PC with LCD Projector or Flip Chart
• Participant Manual
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts
Say
• The term “inspection” generally refers to the activity of checking products, whereas “audit” applies
to analyzing a manufacturing organization.
• The ISO 2859 standard defines an inspection as an “activity such as measuring, examining, testing or
gauging one or more characteristics of a product or service, and comparing the results with specified
requirements”.
• The inspected products can be the components used for production, work -in-process inventory, or
finished goods.
• Quality control in the automobile industry forms an important aspect of the production process,
because of the complexity of the mechanical parts involved and the necessity of their lending
themselves to proper assembly with other portions of the engine.
• Combinations of tools and techniques work together in the quality control process within the
automobile industry.
• A pre-delivery inspection is a standard procedure carried out or a finished component/subassebly/
aggregate by quality team. A pre-delivery inspection ensures that any remark that has to be done is
carried out prior to the product reaching the customer. The product should then be conferming to the
product drawing specifications.
187
Facilitator Guide
• The pre-delivery inspection will give you one last chance to make sure the finished components/
subassembly/aggregate have been manufactured as specified, and will provide the opportunity to do
a final quality control check before the goods are shipped.
Elaborate
Pre-delivery inspection (PDI)
Example of a finished vehicle-In a pre-delivery inspection, the vehicle is checked over to ensure
that everything is working properly and safely. Often a checklist is worked through. The items on the
checklist include such things as the exterior of the vehicle which is inspected for its condition and the
installation of panels and attachments. Any defects identified have to be noted.
The interior of the vehicle is also inspected in a pre delivery inspection. This includes the interior
condition and installation of any of the panels and items. Defects are identified and noted on the check
list. Simple repairs are done on the spot.
In the next part of a pre delivery inspection, the engine is checked over for tightness and leakages.
Any simple adjustments can be made, and any simple defects can be rectified. Fluid levels under the
bonnet are checked with the engine off.
The engine is also started and brought up to normal operating temperature, and again checks are
carried out on fluid levels, leaks and tightness of the engine components. Simple adjustments can be
made according to vehicle manufacturer’s specifications. During a pre -delivery inspection, the vehicle
will be taken for a run and operated in compliance with the Road Code to test its operation.
188
Welding and Quality
Technician
Ask
• Ask about importance of inspection and quality control.
• Ask about pre-delivery inspection (PDI).
• Ask about things have to check in PDI.
189
Facilitator Guide
Unit Objectives
At the end of this unit, Students will be able to:
1. Explain objectives & purpose of inspection.
2. Carry out inspection of final product.
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster, participant manual.
• PC with LCD Projector or Flip Chart
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• Inspection is the most common method of attaining standardisation, uniformity and quality of
workmanship. It is the cost of controlling the product quality after comparison with the established
standards and specifications. It is the function of quality control.
• Inspection is an indispensable tool of modern manufacturing process. It helps to control quality,
reduces manufacturing costs, eliminate scrap losses and assignable causes of defective work.
• Purpose of Inspection
o To distinguish good lots from bad lots
o To distinguish good pieces from bad pieces.
o To determine if the process is changing.
o To determine if the process is approaching the specification limits.
o To rate quality of product.
o To rate accuracy of inspectors.
o To measure the precision of the measuring instrument.
190
Welding and Quality
Technician
Elaborate
Objectives of Inspection
1. To collect information regarding the performance of the product with established standards for
the use of engineering production, purchasing and quality control etc.
2. To sort out poor quality of manufactured product and thus to maintain standards.
3. To establish and increase the reputation by protecting customers from receiving poor quality
products.
4. Detect source of weakness and failure in the finished products and thus check the work of
designer.
Stages of Inspection
1. Inspection of incoming material
2. Inspection of production process
3. Inspection of finished goods.
Inspection Procedures
1. Inprocess/Inspection: It suggests the checking of materials in process at the machine or in
the production time by patrolling inspectors. This method of inspection minimise the material
handling, does not disrupt the line layout of machinery and quickly locate the defect and readily
offers field and correction.
Advantages of floor inspection
(1) Encourage co-operation of inspector and foreman.
(2) Random checking may be more successful than batch checking.
(3) Does not delay in production.
(4) Saves time and expense of having to more batches of work for inspection.
(5) Inspectors may see and be able to report on reason of faulty work.
Disadvantages of floor inspection
(1) Difficult in inspection due to vibration.
191
Facilitator Guide
Methods of Inspection
1. 100% Inspection: This type will involve careful inspection in detail of quality at each strategic
point or stage of manufacture where the test involved is non-destructive and every piece is
separately inspected. It requires more number of inspectors and hence it is a costly method.
192
Welding and Quality
Technician
There is no sampling error. This is subjected to inspection error arising out of fatigue, negligence,
difficulty of supervision etc. It is suitable only when a small number of pieces are there or a
very high degree of quality is required. Example: Jet engines, Aircraft, Medical and Scientific
equipment.
2. Sampling Inspection: In this method randomly selected samples are inspected as per the
aplicable IS standards. Samples taken from different batches of products are representatives.
If the sample proved defective, the entire lot is to be rejected or revoked. Sampling inspection
is cheaper and quicker. It requires less number of Inspectors. It is subjected to sampling errors
but the magnitude of sampling error can be estimated. In the case of destructive test, random
or sampling inspection is desirable. It is suitable for inspection of products which have less
precision importance and are less costly. Example: Electrical bulbs, radio bulbs, washing
machine etc.
Drawbacks of Inspection
1. Inspection adds to the cost of the product but not for its value.
2. It is partially subjective, often the inspector has to judge whether a product passes or not.
3. Fatigue and Monotony may affect any inspection judgement.
4. Inspection merely separates good and bad items. It is no way to prevent the production of bad
Ask
• Ask about inspection process.
• Ask about stages and methods of inspection.
• Ask about inspection procedure.
193
Facilitator Guide
Unit Objectives
At the end of this unit, Students will be able to:
1. Understand different types of Inspection methods (Dimensional / Layout Inspection) & Inspection
Tools (Micrometer, Vernier Calipers & Height Gauge).
Resources to be Used
• Available objects such as white board marker pens, duster, participant manual.
• PC with LCD Projector or Flip Chart
• Inspection Tools: Micrometer, Vernier Caliper & Height Gauge.
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• Dimensional Inspection is performed to compare the actual condition of a manufactured part or
component to the nominal condition as defined by engineering drawings and blueprints, metal or
film templates (decreasingly), digital files and 3D CAD models (increasingly), or even a master tool or
part.
• Layout Inspection is the complete measurement of all part dimensions show n on the design record.
A layout inspection may be required by some customers for all products annually unless another
frequency is established in a customer approved control plan.
• Inspection tools like micrometer, vernier caliper & height Gauge are utilized for these inspections.
• The Vernier Caliper is a precision instrument that can be used to measure internal and external
distances extremely accurately. Measurements are interpreted from the scale by the user. This is
more difficult than using a digital vernier caliper which has an LCD digital display on which the reading
appears. The manual version has both an imperial and metric scale.
• The micrometer is a precision measuring instrument used by engineers. The object to be measured
is placed between the anvil face and the spindle face. The ratchet is turned clockwise until the object
is ‘trapped’ between these two surfaces and the ratchet makes a ‘clicking’ noise. This means that the
194
Welding and Quality
Technician
Demonstrate
Reading the measurement on a Vernier Calipers
Mathematical method:
Step1: The main metric scale is read first and this shows that there are 13 whole divisions before the 0
on the hundredths scale. Therefore, the first number is 13.
Step2: The’ hundredths of mm’ scale is then read. The best way to do this is to count the number of
divisions until you get to the division that lines up with the main metric scale. This is 21 divisions
on the hundredths scale.
Step3: This 21 is multiplied by 0.02 giving 0.42 as the answer (each division on the hundredths scale is
equivalent to 0.02mm).
Step4: The 13 and the 0.42 are added together to give the final measurement of 13.42mm (the diameter
of the piece of round section steel)
Common Method:
• Alternatively, it is just as easy to read the 13 on the main scale and 42 on the hundredths scale.
The correct measurement being 13.42mm.
195
Facilitator Guide
Activity
• Conduct a skill practice activity.
• Ask the students to assemble together.
• Explain the purpose and duration of the activity.
• Set guidelines pertaining to discipline and expected tasks.
• Do the measurement of given object by using micrometer
196
Welding and Quality
Technician
Do
• Ask them to get practice the activity alone.
• Go around and make sure they are doing it properly.
197
Facilitator Guide
Unit Objectives
At the end of this unit, students will be able to:
1. Understand CAPA.
2. Coordinate with R&D / Quality Manager CAPA C1.
Resources to be Used
• Available objects such as white board marker pens, duster, participant manual.
• PC with LCD Projector or Flip Chart
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• Corrective and preventive actions (CAPA ) are improvements to an organization’s processes taken to
eliminate causes of non-conformities or other undesirable situations.
• CAPA is a concept within good manufacturing practice (GMP), and numerous ISO business standards.
It focuses on the systematic investigation of the root causes of identified problems or identified risks
in an attempt to prevent their recurrence (for corrective action) or to prevent occurrence (for preven-
tive action).
• Corrective actions are implemented in response to customer complaints, unacceptable levels of
product non-conformance, issues identified during an internal audit, or adverse or unstable trends in
product and process monitoring such as would be identified by statistical process control (SPC).
• Preventive actions are implemented in response to the identification of potential sources of noncon-
formity.
• CAPA is part of the overall quality management system (QMS).
198
Welding and Quality
Technician
Elaborate
CAPA Inputs
Inputs such as Complaints, Quality Records, Servicing, Nonconforming Product Supply Chain, Process
Monitoring, Audits and Concessions (Deviations) give specific information to design and deploy CAPA
actions.
• Risk assessment and prioritization - Risks associated with the above identified inputs are analysed
and prioritized as per the SOP/requirement of the organization.
• Investigation disciplines - A detailed investigation of the risks are then conducted through various
inspection methods.
• Verification / validation – The results of the above investigations are validated against desired
outcomes and verified for conformity of standards.
• Well defined action plan – A CAPA action plan is prepared where all the action items and
modifications are defined to the last element.
• Documentation rules – All the standard rules of documenting the CAPA process is carried out as
an ongoing activity and checked for conformity.
• Effectiveness checks - The CAPA which is set in motion will be checked for its completeness,
effectiveness and confirmation to the set timelines.
• Management escalation – The problems identified, if any, after determining their severity, are
escalated to the management for review
Ask
• Ask about CAPA.
• Ask about CAPA Inputs.
199
Facilitator Guide
Unit Objectives
At the end of this unit, students will be able to:
1. Understand the objectives of PPAP-PSW.
Resources to be Used
• Available objects such as white board marker pens, duster, participant manual.
• PC with LCD Projector or Flip Chart
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• The Part Submission Warrant or PSW is a document that summaries the whole ‘PPAP Package’.
Elaborate
PSW document include following details:
1) Part Information
• Part Name - The part name is the parts official name for example Pedal Box or Bonnet Locking
Platform. This benefits the manufacturer by giving the part a more human name and decreasing
the chance of errors for example calling the part QNCA0001450002N could easily be mixed up if
multiple PPAPs were being discussed.
• Part Name on Drawing - The part name on the drawing is the part ID written or stamped onto the
drawing for example QNCA0001450002N.
• Engineering Change Level - Will be specified by the manufacturer and could include any
manufacturing change such as tool modifications.
200
Welding and Quality
Technician
• Additional Engineering Changes - Will be specified by the manufacturer and could include any
manufacturing change such as tool modifications.
• Safety and/or Government Regulation - Are there any safety and/or government regulation that
the manufacturer need to be aware of. These should be listed and relevant documents included
or referred to.
• Checking Aid Number - ID of any special tools used while completing the PPAP.
• Checking Aid Engineering Change Level - What is the level of the checking equipment you use to
check this part are there any special tools used?
• Customer Part Number - The number the customer uses on their system to identify the part. This
is very helpful to know when speaking to different department in the manufacturers company as
not everyone will know the suppliers part number.
• Organization Part Number - The number the organization uses on their system to identify the
part.
• Suppliers Address
4) Materials Reporting
• In what format will you submit IMDS or IMDS like information? IMDS ID.
I. Initial Submission
201
Facilitator Guide
X. Other (Specify)
5. Level 5 – Warrant with product samples and complete and complete supporting data reviewed at
suppliers manufacturing location.
7) Submission Results
i. Dimensional measurements
Do all the results meet all the design requirements with any concerns noted Mold / Cavity /Production
Process ID
8) Declaration
9) Explanations or Comments
• Comments / Explanations
• Printed name
202
Welding and Quality
Technician
• Job Title
10) Status
Ask
• Ask about PSW.
• Ask about details required in a PSW.
203
Facilitator Guide
Unit Objectives
At the end of this unit, Students will be able to:
1. Understand the importance of ISO/TS 16949
Resources to be Used
• Available objects such as white board marker pens, duster, participant manual.
• PC with LCD Projector or Flip Chart
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• ISO/TS 16949 was prepared by the International Automotive Task Force (IATF), with support from
ISO/TC 176, Quality management and quality assurance.
• ISO/TS 16949 specifies the requirements of ISO 9001 for automotive production.
• This technical specification combines all previous and published national automotive quality standards
such as QS-9000, VDA 6.1, EAQF 94, and AVSQ.
Elaborate
Why is ISO/TS 16949 important?
ISO/TS 16949 certification demonstrates that your company has met the quality management system
requirements to create a process of continuous improvement with an emphasis on defect prevention
and reduction of variation and waste in the supply chain. The technical specification is implemented
for all branches of manufacturers and suppliers of products or production materials, services such
as heat treatment or galvanizing, and other products specified by automotive customers such as the
constituent parts of vehicles.
204
Welding and Quality
Technician
Ask
• Ask about ISO/TS 16949 certification.
• Ask about benefits of ISO/TS 16949 certification.
205
Facilitator Guide
Unit Objectives
At the end of this unit, Students will be able to:
1. Understand the discipline 8ds.
Resources to be Used
• Available objects such as white board marker pens, duster, participant manual.
• PC with LCD Projector or Flip Chart
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• Eight Disciplines (8Ds) is a problem solving method developed at Ford Motor Company used to
approach and resolve problems, typically employed by engineers or other professionals.
• Focused on product and process improvement, its purpose is to identify, correct, and eliminate
recurring problems.
• It establishes a permanent corrective action based on statistical analysis of the problem and on the
origin of the problem by determining the root causes.
• 8D follows the logic of the PDCA cycle.
• 8Ds has become a standard in the automotive, assembly and other industries that require a thorough
structured problem solving process using a team approach.
Elaborate
8D are:
• D0: Plan: Plan for solving the problem and determine the prerequisites.
206
Welding and Quality
Technician
Ask
• Ask about what is 8D?
• Ask about 8D’s.
207
Facilitator Guide
Unit Objectives
At the end of this unit, Students will be able to:
1. Explain what is FMEA.
2. Understand the relation between 8D & FMEA.
Resources to be Used
• Available objects such as white board marker pens, duster, participant manual.
• PC with LCD Projector or Flip Chart
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• FMEA is called failure modes and effects analysis.
• Failure modes and effects analysis (FMEA) is a step -by-step approach for identifying all possible
failures in a design, a manufacturing or assembly process, or a product or service.
• “Failure modes” means the ways, or modes, in which something might fail. Failures are any errors
or defects, especially ones that affect the customer, and can be potential or actual. “Effects analysis”
refers to studying the consequences of those failures.
• The purpose of the FMEA is to take actions to eliminate or reduce failures, starting with the highest-
priority ones.
• When to Use FMEA
o When a process, product or service is being designed or redesigned, after quality function
deployment.
o When an existing process, product or service is being applied in a new way.
o Before developing control plans for a new or modified process.
o When improvement goals are planned for an existing process, product or service.
208
Welding and Quality
Technician
Elaborate
FMEA Procedure
• Assemble a cross-functional team of people with diverse knowledge about the process, product
or service and customer needs. Functions often included are: design, manufacturing, quality,
testing, reliability, maintenance, purchasing (and suppliers), sales, marketing (and customers)
and customer service.
• Identify the scope of the FMEA. Is it for concept, system, design, process or service? What are
the boundaries? How detailed should we be?
• Fill in the identifying information at the top of FMEA form.
• Identify the functions of scope. Ask, “What is the purpose of this system, design, process or
service? What do our customers expect it to do?”
• For each function, identify all the ways failure could happen.
• For each failure mode, identify all the consequences on the system, related systems, process,
related processes, product, service, customer or regulations. These are potential effects of
failure.
• Determine how serious each effect is. This is the severity rating or S and it is usually rated on
a scale from 1 to 10, where 1 is insignificant and 10 is catastrophic. If a failure mode has more
than one effect, write on the FMEA table only the highest severity rating for that failure mode.
• For each failure mode, determine all the potential root causes. Use tools classified as cause
analysis tool, as well as the best knowledge and experience of the team. List all possible causes
for each failure mode on the FMEA form.
• For each cause, determine the occurrence rating, or O. This rating estimates the probability of
failure occurring for that reason during the lifetime of your scope. Occurrence is usually rated
on a scale from 1 to 10, where 1 is extremely unlikely and 10 is inevitable.
• For each cause, identify current process controls. These are tests, procedures or mechanisms
that you now have in place to keep failures from reaching the customer.
• For each control, determine the detection rating, or D. This rating estimates how well the
controls can detect either the cause or its failure mode after they have happened but before
209
Facilitator Guide
the customer is affected. Detection is usually rated on a scale from 1 to 10, where 1 means the
control is absolutely certain to detect the problem and 10 means the control is certain not to
detect the problem (or no control exists).
• (Optional for most industries) Is this failure mode associated with a critical characteristic?
(Critical characteristics are measurements or indicators that reflect safety or compliance with
government regulations and need special controls.) If so, a column labelled “Classification”
receives a Y or N to show whether special controls are needed. Usually, critical characteristics
have a severity of 9 or 10 and occurrence and detection ratings above 3.
• Calculate the risk priority number, or RPN, which equals S × O × D. Also calculate Criticality by
multiplying severity by occurrence, S × O. These numbers provide guidance for ranking potential
failures in the order they should be addressed.
• Identify recommended actions. These actions may be design or process changes to lower
severity or occurrence.
• As actions are completed, note results and the date on the FMEA form. Also, note new S, O or
D ratings and new RPNs.
210
Welding and Quality
Technician
Ask
• Ask about what is FMEA?
• Ask about FMEA procedure.
• Ask about relationship between FMEA and 8D.
211
Facilitator Guide
Unit Objectives
At the end of this unit, Students will be able to:
1. Explain what is 5 Whys.
Resources to be Used
• Available objects such as white board marker pens, duster, participant manual.
• PC with LCD Projector or Flip Chart
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• A discussion of the unexpected event or challenge that follows one train of thought to its logical
conclusion by asking “Why?” five times to get to the root of what happened.
• The 5 Whys technique was developed and fine-tuned within the Toyota Motor Corporation as a
critical component of its problem-solving training.
Elaborate
5 Why process
• Invite anyone affected by the issue: As soon as the problem or situation is identified (and
all immediate concerns are dealt with), invite anyone at all on the team who was affected or
noticed the issue to be involved in a 5 whys meeting.
• Select a 5 Whys master for the meeting: The 5 Whys master will lead the discussion, ask the
5 whys and assign responsibility for the solutions the group comes up with. The rest of those
involved will answer those questions and discuss.
212
Welding and Quality
Technician
• Ask “why” 5 times: Dig at least 5 levels deep into the issue with 5 levels of “whys.” This seems
like the simplest part, but can in fact get a bit difficult in getting the right question to start with,
the first why, seems to be the key.
• Assign responsibility for solutions: At the end of the exercise, go through each why question
and- answer pairing and come up with 5 related “corrective actions” that everyone agree on.
The master assigns responsibility for the solutions to various participants in the discussion.
• Share the results: After each 5 Whys process, someone involved in the meeting will write down
what was discussed in the clearest, plainest language as possible and shares the result with all
concerned.
Ask
• Ask about what is 5 Whys?
• Ask about 5 Whys procedure.
• Ask about need of 5 Whys.
213
Facilitator Guide
Notes
214
9. Maintaining a safe,
Clean and secure working
environment
Unit 9.1 – Health and Safety
Unit 9.2 – Personal Protective Equipment of Workers
Unit 9.3 – Hazards
ASC/N0006
Facilitator Guide
216
Welding and Quality
Technician
Unit Objectives
At the end of this unit, you will be able to:
1. Understand health, safety and security procedure
Resources to be Used
• Available objects such as white Board, white board marker pens, duster.
• PC with LCD Projector or Flip Chart
• Participant Manual
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• Health, safety and security procedures refer to the guidelines and rules that make sure that people in
the workplace, whether they are employers, employees or other visitors are safe and secure.
• These procedures tell employees or employers how they should carry out their tasks around the
workplace in a way that ensures a minimization in accidents, incidents, contraction of diseases and
security breaches.
Elaborate
Preventative procedures may include:
• Educating staff on manual handling, i.e.: how to lift and move objects properly to avoid an injury
• Educating staff on how to minimize back and neck pain by using ergonomic furniture in an
appropriate fashion
• Giving detailed instructions on how to use equipment
217
Facilitator Guide
• Educating staff on the importance of wearing appropriate protective gear to handle certain pieces
of equipment
• Instructing staff on how to keep the workplace secure, by teaching them about the security
systems in place and how to use them so that cash, equipment and people are safe and secure
• Educating staff on potential hazards in the workplace.
• Health, safety and security procedures also refer to what you should do when accidents or
incidents do occur.
Ask
• Ask about organization safe operating procedures
• Ask about need of safe operating procedures
218
Welding and Quality
Technician
Unit Objectives
At the end of this unit, you will be able to:
1. Identify the Safety Equipment required
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster, participant manual.
• PC with LCD Projector or Flip Chart.
• PPE
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• PPE refers to the equipment worn by staff to reduce the exposure to hazards.
• PPE include such items as: gloves, safety boots, earplugs, safety hat, face mask, welding shield etc.
• There are two things to consider in regards to PPE:
o PPE protects only the wearer, whereas measures controlling the risk at source can protect
everyone in the workplace.
o The specified level of protection in reality may not be achieved with PPE and the actual level of
protection provided is difficult to assess
219
Facilitator Guide
Elaborate
PPE items may include:
• Gloves – Always wear gloves when you are working with any sharp tools, knives or materials. You
should also wear gloves when working with some cleaning agents, glues, etc.
• Foot protection (safety boots) - Safety boots are necessary if you are working in a building site or
in an area where heavy objects can fall on you.
• Body protection – aprons, gowns - Additional protective clothing may be necessary when cleaning
duties require the use of various chemicals and/or disinfectants.
• Hearing protection – ear muffs, ear plugs - Ear muffs should be used when working in an
environment to protect your ears if there is regular noise or occasional sounds that are louder.
• Face masks – Use face masks to get the protection from gases, poisonous fumes, dust, vapours
etc. Face mask protect our self from flying particles and harmful radiation.
• Head protection – hard hats - If you are working in an area where tradesmen are working above
you, you should wear a hard hat.
• Eye protection – goggles, glasses - When working outside you should wear protection glasses to
protect you from the sun ultra -violet rays.
Ask
• Ask about PPE
• Ask about need of PPE
Do
• Show the PPE to trainees.
• Demonstrate them how to wear the PPE properly.
• Explain the functioning of every item of PPE.
220
Welding and Quality
Technician
Unit Objectives
At the end of this unit, you will be able to:
1. Identify activities causing potential hazards.
2. Explain safe practises for avoiding hazards.
Resources to be Used
• Available objects such as whiteboard, white board marker pens, duster, participant manual.
• PC with LCD Projector or Flip Chart.
Do
• Welcome and greet the participants. Revise the learnings of the previous sessions and ask them if
they have any doubts.
Say
• A hazard is a situation that poses a level of threat to life, health, property, or environment.
• The main hazards can happen during work are:
o Fire caused by heat, sparks, molten metal or direct contact with the flame.
o Explosion when cutting up or repairing tanks or drums which contain or may have contained
flammable materials.
o Fire/explosion caused by gas leaks, backfires and Flashbacks.
o Fumes created during flame cutting.
o Fire/burns resulting from misuse of oxygen.
o Burns from contact with the flame or hot metal.
o Crushing or impact injuries when handling and transporting cylinders.
• To assure a high degree of safety, no machine-tool is to be used unless the risk management process
applied on it.
221
Facilitator Guide
• While working in workplace you have to follow personal safety procedures when dealing with tools
and equipments. You have to follow Standard Operating Procedures (SOP’s) must be maintained for
each piece of machinery in the shop.
• The Hazardous Material can be: Flammable, Reactive, Toxic and Corrosive.
Elaborate
Risk management process
1. Identify the potential hazard(s) that the machine tool can generate.
2. Assess the probability and severity of the hazard(s) by utilizing the Risk Assessment Matrix. Risk
acceptance decision authority for the risk levels is as follows:
3. Determine the risk control measures that will eliminate the hazard(s) or reduce the risk.
4. Supervise and evaluate the process. Enforce the established standards and risk control measures.
Probability of hazard
• Frequent - Occurs often in the career/equipment service life. Continuously experienced during
operation.
• Likely - Occurs several times in career/equipment service life. Occurs frequently during operation.
• Unlikely - Can assume will not occur in career/ equipment/ service life. Possible, but improbable;
occurs only very rarely during operation.
Severity of hazard
• Catastrophic - Death or permanent total disability, system loss or major property damage.
222
Welding and Quality
Technician
• Critical - Permanent partial disability, temporary total disability in excess of 3 months, major
system damage or significant property damage.
• Marginal - Minor injury, lost workday accident with compensable injury/illness, mirror system
damage or minor property damage.
1. If you find any problem or hazard situation, remedial action should be completed as soon as
possible.
2. Give remedial action priority to hazards with more severe loss potential.
3. Obtain target dates for correction. Use hazard classification to motivate correction.
4. Write a detailed explanation of the hazard and its potential loss severity as justification for any
action requiring a major expenditure and forward it to the person most responsible for corrective
action.
5. Encourage responsible persons to take permanent corrective action (repetitive remedy is costly).
6. Make sure intermediate (temporary) safety measures are taken whenever permanent or complete
remedy will require additional time.
7. At a reasonable time after the inspection is conducted and necessary action is submitted, do a
follow-up walk through to ensure that the corrective action has been completed.
8. Make sure all reports are properly filed and maintained for record purposes.
• Hot Work: Hot work is defined as any work producing an arc, flame, or spark. The only exception
to this are those areas specifically designed and or built for welding, cutting or brazing.
• Confined Space Entry: Entry to confined spaces is very dangerous and requires special precautions
in addition to a permit issued by a supervisor. Confined spaces are defined as tanks, vessels,
sewers, pits, boilers, manholes, etc.
• High Voltage Electricity: Only specially trained maintenance employees/electricians are permitted
to work with high voltage equipment.
223
Facilitator Guide
• Fire caused by heat, sparks, molten metal or direct contact with the flame.
• Explosion when cutting up or repairing tanks or drums which contain or may have contained
flammable materials
2. Keep the floor clear of stock and tools, and clean spilled oils or coolants
2. What are the potential hazards involved with using this machine?
6. Have I made all the proper adjustments and tightened all locking mechanisms?
224
Welding and Quality
Technician
Ask
• You can ask the different ideas to control the hazard.
• You could ask the common causes of hazard.
• You can pick the students and ask the safe practices for avoiding general shop hazards.
Team Activity
• Conduct a skill practice activity.
• Ask the students to assemble together.
• Explain the purpose and duration of the activity.
• Make the 5 teams.
• Divide the complete training center area into five different areas like cafeteria, workshop, classroom,
training center admin block, washrooms etc.
• Assign one area to each team.
• Tell them to go their area and identify the reasons of hazards in that area.
• Once they back, they have to present what type of hazards they identified and what precautions have
to be taken to control those hazards.
• Go around and make sure they are doing it properly.
• Wrap the unit up after summarizing the key points and answering questions.
225
Facilitator Guide
Notes
226
Welding and Quality
Technician
227
Facilitator Guide
Facilitator Guide
This Facilitator's guide includes various activities which will help you as a facilitator to make the sessions
participative and interactive.
Ice breaker
You can begin the module with the following ice breaker:
Five of Anything Ice Breaker Steps:
Divide the participants into groups of four or five by having them number off. (You do this because people
generally begin a meeting by sitting with the people they already know best.)
Tell the newly formed groups that their assignment is to share their five favourite movies of all time, their five
favourite novels or their five least liked films. The topic can be five of anything ‐ most liked or disliked.
This ice breaker helps the group explore shared interests more broadly and sparks lots of discussion about
why each person likes or dislikes their selected five.
Tell the groups that one person must take notes and be ready to share the highlights of their group discussion
with the class upon completion of the assignment.
Expectation Mapping
1. During the first session and after ice breaker session, ask the participants to answer the following question:
"What do I expect to learn from this training?"
2. Have one of the participants write their contributions on a flip chart sheet.
3. Write down your own list of covered material in the training on another flip chart sheet.
4. Compare the two sheets, commenting on what will and what will not be covered during the training.
5. Set some ground rules for the training sessions. Ask the participants to put these rules on a flipchart and
display it in the class.
6. You may get back to those sheets once again at the end of the last session of the training.
7. Benefits of doing this activity:
Participants feel better as their opinions are heard.
Participants get to know what they should expect from the training.
The facilitator gets to know which points to emphasize, which to leave out, and which to add during the
training.
8. Expectations from the participants:
• Must sign the attendance sheet when they arrive for class.
• Conduct themselves in a positive manner
• Be punctual, attentive, and participative
9. Explain the contents that are going to get covered one by one and connect it with the expectation mapping
done earlier.
10. By the end of this exercise, the participants should have a clear understanding of what to expect from the
session and what are the areas that will not get covered.
Defining Objectives
1. Defining the objectives in the beginning of the units sets the mood for the unit.
2. To begin with the end in mind sets the expectations of the participants as what could be the important
takeaways from the session.
3. It is also a way of making participants take responsibility of their own learning process.
4. For the facilitator, the objectives decide a designed path to progress on so that the learning stays aligned and
on track.
2228
Welding and Quality
Employability & Entrepreneurship Skills
Technician
5. Read the objectives slowly, one by one, and ask the participants to explain what they think it means.
6. At the end of the session, you could again revisit the objectives to find out from the participants about how
many objectives have been achieved.
In order to effectively facilitate this workshop:
1. You must have thorough knowledge of the material in the Participant Handbook, and be prepared to answer
questions about it.
2. You may also wish to read other material to enhance your knowledge of the subject.
3. There may be issues raised with which you are not able to deal, either because of lack of time or knowledge.
You can either state that you will obtain answers and get back to the participants with the information.
Incase the query can be turned to an assignment to the class, do so. You can work with the the participants
on the assignement.
4. You must have a very clear understanding of what the participants want to accomplish by the end of the
workshop and the means to guide the participants.
5. As the facilitator, it is your responsibility to make sure that all logistical arrangements are made for the
workshop. This may involve doing it yourself or confirming that someone else has made all necessary
arrangements associated with the workshop. Assume nothing and check everything before the workshop
begins.
6. To break the monotony and boredom during sessions, introduce mini breaks in the form of stretching
exercises, jokes, some group songs or games.
7. Invite discussion from the participants.
8. Probe the participants further and lead them to come to affirmative conclusions.
9. Let the participants answer. No answer is incorrect.
10. Ask one participant to write all the points on the whiteboard.
11. Build the sessions from the answers provided by the class.
12. Prepare for the sessions in advance so that the resources like flipcharts, handouts, blank sheets of paper,
marker pens, etc. can be kept ready.
13. Ensure that resources like board, markers, duster etc. is available before your session starts.
General instructions for role playing:
1. You are not being asked to be an actor or to entertain. The purpose of the role play is to provide a situation in
which you can practice certain skills.
2. When you read the brief, try to imagine yourself in the situation described and behave in a way you feel to be
natural – but be conscious of the fact that your role may require a different approach from that which you
might normally use.
3. You (and others) may benefit from the change in approach and behaviour. Therefore, try to use the approach
you feel to be most appropriate for the circumstances described in your brief.
4. The brief is just the starting point. It simply sets the scene and the tone of session or activity. Try not to keep
referring to the brief as this will affect the spontaneity of the meeting. Allow the role play to develop as you
think it might in real life and change your reactions in line with the behaviour and responses of others
involved.
5. If you find that you have too little information to answer questions or to describe what has happened in the
situation, do feel free to add your own thoughts and ideas. Try to keep these within the framework of the
role you are taking and try to make your improvisations as realistic as possible.
3229
Facilitator Guide
Facilitator Guide
4230
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Unit Objectives
At the end of this unit, participants will be able to:
Explain the meaning of health
List common health issues
Discuss tips to prevent common health issues
Explain the meaning of hygiene
Discuss the purpose of Swachh Bharat Abhiyan
Explain the meaning of habit
Resources to be Used
Participant Handbook
Ask
What do you understand by the term “Health?”
According to you, who is a healthy person?
Say
Discuss the meaning of health and a healthy person as given in the Participant Handbook.
Ask
When did you visit the doctor last? Was it for you or for a family member?
Say
Discuss the common health issues like common cold, allergies etc. Refer to the Participant Handbook.
Let us do a small activity. I will need some volunteers.
Role Play
Conduct a small skit with volunteers from the class. Consider one of the villagers has been appointed as a
health representative of the village, what measures will you as a health representative suggest to the
common villagers to prevent common health issues discussed.
You will need at least 4 volunteers (Narrator, Health Representative, Head of the Village, Doctor).
Explain the health concerns of the village to the Narrator. The Narrator will brief the class about the skit.
Give the group of volunteers, 5 minutes to do discuss.
At the end of 5 minutes, ask the group to present the skit to the class assuming them as the villagers.
The class can ask questions to the group as a common villager.
Summarize
Through this activity we got some tips on how can we prevent these common health issues.
5231
Facilitator Guide
Facilitator Guide
Say
Let us now see how many of these health standards we follow in our daily life.
Activity
Health Standard Checklist from the Participant Handbook.
Ask
How many of you think that you are healthy? How many of you follow healthy habits?
Say
Let's do an exercise to find out how healthy you are.
Open your Participant Handbook section ‘Health, Habits, Hygiene: What is Health?’, and read through the
health standards given.
Tick the points which you think are true for you.
Try to be as honest as possible as this test is for your own learning.
Do
Ensure that all the participants have opened the right page in the Participant Handbook.
Read aloud the points for the participants and explain if required.
Give them 5 minutes to do the exercise.
At the end of 5 minutes, ask the participants to check how many ticks have they got.
Summarize
Tell them that they need to follow all the tips given in this checklist regularly in order to remain healthy and fit.
Ask
Discuss:
Is it necessary to practice personal hygiene every day? Why?
How does a person feel when they do not practice good personal hygiene? Why?
Can good personal hygiene help a person feel good about his/her self? How?
Say
Discuss the meaning of hygiene as given in the Participant Handbook.
Activity
Health Standard Checklist: Hygiene
6232
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Say
Let's do an exercise to find out if we maintain good hygiene habits or not.
Open the Participant Handbook and read through the Health Standard checklist given.
Tick the points which you think are true for you.
Try to be as honest as possible as this test is for your own learning.
Do
Ensure that all the participants have opened the right page in the Participant Handbook.
Read aloud the points for the participants and explain if required.
Give them 5 minutes to do the exercise. .
At the end of 5 minutes, ask the participants to check how many ticks have they got.
Ask them to calculate their score.
Tell them what each score indicates by reading aloud what has been mentioned in the Participant Handbook.
Ask
How many of you have heard about “Swachh Bharat Abhiyan”?
Can you tell the class what it is about?
Summarize
Tell them about Swachh Bharat Abhiyan as given in the Participant Handbook and request them to take a
pledge to keep our country clean.
Ask
What is a habit?
Say
Discuss some good habits which can become a way of life.
Summarize
Tell them about good and bad habits and the reasons to make good habits a way of life.
7233
Facilitator Guide
Facilitator Guide
Unit Objectives
At the end of this unit, participants will be able to:
Discuss ways to set up a safe work environment
Discuss critical safety habits to be followed by employees
Resources to be Used
Participant Handbook
Safety signs and symbols
Safety equipments
Blank papers
Pens
Say
There are many common safety hazards present in most workplaces at one time or another. They include
unsafe conditions that can cause injury, illness and death.
Safety Hazards include:
Spills on floors or tripping hazards, such as blocked aisles or cords running across the floor.
Working from heights, including ladders, scaffolds, roofs, or any raised work area.
Unguarded machinery and moving machinery parts; guards removed or moving parts that a worker can
accidentally touch.
Electrical hazards like cords, missing ground pins, improper wiring.
Machinery‐related hazards (lockout/tag out, boiler safety, forklifts, etc.)
Team Activity
Safety Hazards
There are two parts to this activity.
First part will cover the potential safety hazards at work place.
Second part will cover a few safety signs, symbols and equipments at work place.
Use this format for the first part of the activity.
PART 1
Ask
How could you or your employees get hurt at work?
8234
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Say
Let's understand it better with the help of an activity. You will be given a handout within your groups. You
have to think about the possible hazards of your workplace, what damage these hazards could cause and
about the corrective action.
Do
Divide the class into five to six groups of four participants each.
Put the format on the board for the activity.
Give blank papers and pens to each group.
The group is expected to think and discuss the potential safety hazards in the workplace.
Ask the group to discuss and fill the format using the blank sheet.
Give the groups 5 minutes for the activity.
For the second part of the activity, show the class some pictures of safety signs, symbols and equipments.
Now they will put down a few safety symbols, signs or equipment against the safety hazards identified.
Give them 5 to 10 minutes to discuss and draw/note it.
At the end of 10 minutes the groups will present their answers to the class.
Say
Now, let's discuss the answers with the class.
All the groups will briefly present their answers.
Do
Ask the audience to applaud for the group presentation.
Ask de‐brief questions to cull out the information from each group.
Keep a check on time.
Tell the group to wind up the discussion quickly if they go beyond the given time limit.
Ask
De‐briefing
What did you learn from the exercise?
As an entrepreneur, is it important to ensure the safety of your employees from possible hazards? Why?
Summarize
Ask the participants what they have learnt so far.
Ask if they have any questions related to what they have talked about so far.
Close the discussion by summarizing the tips to design a safe workplace and non‐negotiable employee safety
habits.
9235
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Old newspapers
Blank papers
Pencils/ pens
Activity
This is a paper pencil activity.
What are the three sentences that describe you the best?
Do
Write the three questions on the board/ flipchart before the session begins.
Give plain papers and pencils/ pens to each participant.
Tell participants to write the answer for the three questions on the paper.
Tell them the purpose of this activity is not to judge anyone but to understand more about self.
Say
Discuss the concept of Self Analysis and motivation with reference to Maslow's Hierarchy of Needs as
discussed in the Participant Handbook.
Team Activity
Tower building
Each group which will create tower using the old newspapers.
236
10
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Do
Divide the class into groups.
Give them some old newspapers.
The task is to create a tower out of the newspapers.
The group which will create the highest tower standing on its own will be considered the winning group.
Groups can use as many newspapers as they want to and in any way they want.
Ask
What did the winning group do differently?
If you were given a chance, how would you have made the tower differently?
How did you feel while making the tower?
Did you feel motivated?
Say
Discuss the concept of achievement motivation and characteristics of entrepreneurs with achievement
motivation as discussed in the Participant Handbook.
Ask
Is your attitude positive or negative?
Say
Let me tell you a story :
It's Little Things that Make a Big Difference.
There was a man taking a morning walk at the beach. He saw that along with the morning tide came hundreds of
starfish and when the tide receded, they were left behind and with the morning sun rays, they would die. The
tide was fresh and the starfish were alive. The man took a few steps, picked one and threw it into the water. He
did that repeatedly. Right behind him there was another person who couldn't understand what this man was
doing. He caught up with him and asked, “What are you doing? There are hundreds of starfish. How many can
you help? What difference does it make?” This man did not reply, took two more steps, picked up another one,
threw it into the water, and said, “It makes a difference to this one.” What difference are we making? Big or small,
it does not matter. If everyone made a small difference, we'd end up with a big difference, wouldn't we?
Ask
What did you learn from this story?
Activity
What Motivates You?
This is an individual activity.
It is an exercise given in the Participant Handbook.
Do
Ask the class to open their Participant Handbook and complete the exercise given in the section What
Motivates You?
Ensure that the participants have opened the correct page for the activity.
Give the class 5 minutes to complete the activity.
237
11
Facilitator Guide
Facilitator Guide
Say
Discuss the concept of attitude and how to cultivate a positive attitude as discussed in the Participant
Handbook.
Summarize
Close the discussion by summarizing how self‐analysis, knowledge about what motivates you and your
positive attitude can help in your business as well in life.
238
12
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Resources to be Used
Participant Handbook
Ask
What do you understand by honesty?
Why is it important for entrepreneurs to be honest?
Do you remember any incident where your honesty helped you in gaining confidence?
Do you remember any incident where someone lost business due to dishonesty?
Say
Talk about honesty, qualities of an honest person, and the importance of honesty in entrepreneurs as
discussed in the Participant Handbook.
“Let's understand it better with the help of some case scenarios. You will be given some cases within your
groups. You have to analyse the case scenario that has been given to you and then find an appropriate
solution to the problem.
Keep your discussion focussed around the following:
What went wrong?
Who was at fault?
Whom did it impact‐ the customer or the businessman?
How would it impact the business immediately? What would be the long term impact?
What could be done?
What did you learn from the exercise?
Do
Divide the class into four groups of maximum six participants depending on the batch size.
Give one case study to each group.
Instruct them to read the case carefully.
Put down the de‐brief questions on the board and ask the groups to focus their discussion around these questions.
The group is expected to analyse and discuss the case amongst them and find a solution to the given problem.
Give the class5‐10 minutes to discuss the case and note down their solutions.
At the end of 10 minutes the team should present their case solution to the class. The presentation can be a
narration or a role play.
Ask the group to select a group leader for their group. The group leader to discuss and assign roles to the
group members for the presentation.
239
13
Facilitator Guide
Facilitator Guide
Team Activity
Case Study Analysis
Scenario 1
Aakash has a small mobile retail sales and repair shop in Allahabad. He has one of the most popular outlets
and has great rapport with his customers.
It's around 11 AM when a customer barges in to the shop and starts shouting at Aakash for giving her a faulty
instrument. The screen of her mobile is cracked from one side. Aakash remembered thoroughly checking the
handset before handing it over to the customer. The customer threatens to sue him and to go to Consumer
Court for cheating her. Now, the problem occurred somewhere outside the shop but as other customers
were listening to the conversation, it might impact his business. The situation needs to be managed very
sensitively. What would you do if you were in Aakash's place?
Scenario 2
Rajni does beautiful Phulkari embroidery on suits and sarees. She has a small home‐based business. She has
a huge list of customers on Facebook and WhatsApp who give her orders regularly. Smita is one of her old and
regular customers. As her sister‐in‐law's weddingwas around the corner, Smita wanted to buy few
handcrafted Phulkari duppatta. She placed an order for three duppattas via WhatsApp and requested Rajni
to send them as soon as possible. When the parcel reached Smita through courier she found that out of the
three duppatas, only one was hand embroidered and the other two had machine embroidery on them. Even
the length and the quality of the material was not as desired. Smita was heartbroken. It was a complete
waste of money and moreover she couldn't wear what she had planned to during the wedding functions. She
sent a message to Rajni on WhatsApp, expressing her anger and disappointment.
Smita has also sent a feedback and expressed her disappointment on the social media… this will directly
affect Rajni's business. What would you do if you were in Rajni's place?
Scenario 3
Shankar is a tattoo artist who has a small tattoo showroom in a big, reputed mall in New Delhi. Mr Saksham had
an appointment for today, at 11:00 am but he reached at 11:50 am. Meanwhile, Shankar had to reschedule his
next appointment. After availing Shankar's services, Mr Saksham started yelling in an abusive language, refusing
to pay the requisite amount, and finding faults in the services provided by him. Who was at fault in this case?
What should Shankar do? Should he confront Saksham or give in to the demands of the client?
Scenario 4
Shailender is an online cloth reseller who does business through social networking sites such as Facebook
and WhatsApp. Priyanka made online payment for a dress to Shailander. But she did not receive the dress for
a month. When she asked for a cancellation, Shailander started misleading her. For almost 45 days, he kept
promising her that he will pay the amount today, tomorrow, day after etc. Even after repeated calls and
messages when she did not receive the payment or the dress, she decided to write a post against him on a
popular social media platform. As a result, Shailender lost lots of customers and his flourishing business
faced a major crisis. How could this situation have been managed?
Say
Now, let's discuss the problem and solution with the larger group.
The group will first briefly describe the case to the class.
Then discuss the issue identified and the proposed solution.
Once the presentation is over, the class can ask their questions.
240
14
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Do
Congratulate each group for the group presentation.
Ask the audience to applaud for them.
Ask de‐brief questions to cull out the information from each group.
Keep a check on time. Tell the group to wind up the discussion quickly if they go beyond the given time limit.
Summarize
Ask the participants what they have learnt from the exercise/ activity.
Ask if they have any questions related to what they have talked about so far.
Close the discussion by summarizing the importance of honesty and work ethics for entrepreneurs.
241
15
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Chart papers
Marker pens
Ask
You must be aware of the term 'Rags to riches' and heard stories related to the term.
What do these stories tell us?
What was so special about these people?
Say
Let's have a look at these stories.
There are some inspiring stories about people which I would like to share with you.
Narrate these stories to the class.
A.P.J. Abdul Kalam
Who has not heard of A.P.J. Abdul Kalam: Avul Pakir Jainulabdeen Abdul Kalam hailed from a very humble
background. His father was a boat owner. To help his family, Kalam would work as a newspaper vendor. With
limited resources, he graduated in Physics and studied aerospace engineering. He was instrumental in India's
step towards nuclear energy. In 2002, he became the 11th President of India.
Solar seeder
This is a story of a innovative solar seeder and developed by Subash Chandra Bose, a class 8, student from St
Sebasthiyar Matriculation School, Pudukkottai, Tamil Nadu. Subash has developed a solar powered seed drill,
which can undertake plantation for different size of seeds at variable depth and space between two seeds.
Source: http://www.rediff.com/getahead/report/achievers‐top‐31‐amazing‐innovations‐from‐young‐
indians/20151208.htm
242
16
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Ask
If they can, why can't you?
Discuss concepts related to 'Creativity and Innovation' with the participants as given in the Participant
Handbook.
Say
Recall the stories on motivation.
What is the inner drive that motivates people to succeed?
Let's learn more about such creative and innovative entrepreneurs with the help of an activity.
Team Activity
This is a group activity.
Think of any one famous entrepreneur and write a few lines about him or her.
Activity De‐brief
Why did you choose this particular entrepreneur?
What is his/her brand name?
What creativity does he/she possess?
What was innovative about their ideas?
Do
Instruct the participants that this is group work.
Divide the class into small groups of 4 or 6 depending on the batch size.
Give each group a chart paper.
Tell the participants they have to write a few lines about any one famous entrepreneur.
Give the participants 10 minutes to discuss and write.
Keep a check on time. Tell the group to wind up quickly if they go beyond the given time limit.
Ask each group to read out what they have written.
Ask the de‐brief questions.
243
17
Facilitator Guide
Facilitator Guide
Summarize
Summarize the unit by asking participants if they know of some people who are highly creative and innovative
in their approach.
Ask them to share some experiences about these people with the class.
244
18
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Resources to be Used
Participant Handbook
Ask
Does this sound like you?
I can never get enough time to finish what I am doing in a day.
I have so many things to do that I get confused.
I want to go for a walk and exercise, but I just do not have the time.
I had so much to do, so I could not deliver that order on time.
I would love to start my dream business; but, I just do not have the time.
Example Example
Example 1:
Ankita works from home as a freelance writer. She says she can easily put in 8 hours of dedicated work in a
day. Because she works from home, she saves money on travel and has a comfortable work routine. But
there is a challenge and it is distraction. As she works from home, she can easily just get up and sit down on
the sofa to watch TV, wasting valuable time. She may have chores to do, errands to run and bills to pay. She
ends up working only two to three hours a day and the result is, her work gets piled up. She is unable to take
on more work due to this. Even though her quality of work is appreciated her clients are not very happy about
the delay in submission.
Example 2:
Javed has started a successful online selling company from home and makes a good living from his sales. He
has set up a small office space in his living room. As both his parents are working full‐time, he also has the role
of taking care of his two younger siblings. He almost spends half of his day with the younger kids. He does not
mind it but it means taking time away from the work. He is still able to manage his online business with these
commitments. He wants to spend some more dedicated hours so as to increase his profits. He also wants to
look into new business avenues. What should he be doing.
Ask
Does this happen with you too?
Do you find it difficult to prioritize your work?
Are you able to manage your time effectively?
245
19
Facilitator Guide
Facilitator Guide
Activity
Conduct a group discussion based on the above examples.
Direct the discussion on how to prioritize work and manage time effectively.
Say
Time management is not only about how hard you work but also about how smart you work.
Discuss “What is Time Management” with the participants as given in the Participant Handbook.
Ask
Why is it important to manage time? How does it help?
What happens when you don't manage your time effectively?
Do you find it difficult to prioritize your work?
Say
Discuss the benefits of time management given in the Participant Handbook.
Let's learn effective time management with the help of an activity.
Activity
Effective Time Management
This activity has two parts:
PART 1
TO‐DO LIST
You have to make a to‐do list.
List all of the activities/ tasks that you have to do.
Try to include everything that takes up your time, however unimportant it may be.
If they are large tasks, break them into action steps, and write this down with the larger task.
You can make one list for all your tasks or have separate to‐do lists for personal and professional tasks.
PART 2
URGENT‐IMPORTANT GRID
You have to make a grid as shown on the board here. .
This grid has four boxes. As you can see, each box has a different heading.
At the heart of the urgent‐important grid, are these two questions:
Is this task important?
Is this task urgent?
Now, you have to think about each activity that you have written in your to‐do list and put it into one of the
four categories.
What do these categories depict?
Category 1: Urgent/Important
This category is for the highest priority tasks. They need to get done now.
246
20
Welding and Quality
Employability & Entrepreneurship Skills
Technician
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
247
21
Facilitator Guide
Facilitator Guide
URGENT‐IMPORTANT GRID
1 2
3 4
1 2
3 4
248
22
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Do
Put down the formats for the to‐do list and the urgent/ important grid on the board.
Instruct the participants to prepare their to‐do list first.
Give the participants 10 minutes to prepare the list.
Once done, instruct them to divide the tasks in to‐do list into the four categories.
Explain the four categories to the participants giving examples specific to their context.
As you explain the categories fill the grid with the type of tasks.
Give the participants 40 minutes to fill the grid.
Then explain how to balance the tasks between the four categories.
Keep a check on time. Tell the group to wind up quickly if they go beyond the given time limit.
Say
Activity De‐brief:
How can we balance tasks between the four categories?
How to manage time through this grid?
Category 1: Urgent/Important
Try to keep as few tasks as possible here, with the aim to eliminate.
If you spend too much of your time in this category, you are working solely as a trouble shooter, and never
finding time to work on longer‐term plans.
Category 2: Not Urgent/Important
Plan these tasks carefully and efficiently as they are most crucial ones for success.
If necessary, also plan where you will do these tasks, so that you're free from interruptions.
Include strategic thinking, deciding on goals or general direction and planning in your planning process.
Category 3: Urgent/Not Important
Ask yourself whether you can reschedule or delegate them.
A common source of such activities is other people. Sometimes it's appropriate to say "no" to people
politely, or to encourage them to solve the problem themselves.
Category 4: Not Important and Not Urgent
You also want to minimize the tasks that you have in this category.
These activities are just a distraction – avoid them if possible.
You can simply ignore or cancel many of them.
Politely say "no" to work assigned by others, if you can, and explain why you cannot do it.
Schedule your leisure activities carefully so that they don't have an impact on other important tasks.
Discuss the traits of effective time managers and effective time management techniques as given in the
Participant Handbook.
Summarize
Discuss the traits of effective time managers and effective time management techniques as given in the
Participant Handbook.
249
23
Facilitator Guide
Facilitator Guide
250
24
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Resources to be Used
Participant Handbook
Ask
What is anger? Is anger good or bad?
Is anger normal or an abnormal behaviour? How can anger harm you?
Why is it important for entrepreneurs to manage their anger?
Say
Talk about anger and the importance of anger management in entrepreneurs as discussed in the Participant
Handbook.
Let us do a small activity. This is an individual activity.
Think of the incidents and situations that angered you and hurt you.
Do
Instruct them to note down these situations under different categories (as given in the Activity).
Give the class 3‐5 minutes to think and note down their answers.
At the end of 5 minutes, ask some participants to volunteer and present their answers.
They can also share these situations with their fellow participants if they do not wish to share it with the
entire class.
Activity
Do you remember any incident which has hurt
you physically
you mentally
your career
your relationships.
Ask
Do you ever get angry?
What are the things that make you angry?
Do you remember any incident where your anger management helped you in maintaining healthy relationship?
Do you remember any incident where someone lost business/ friend/ relationship due to temper (anger)?
251
25
Facilitator Guide
Facilitator Guide
Say
There are a few strategies which can help in controlling your anger. Let's do an activity to understand the
anger management process better.
This is an individual activity.
Think of the incidents/ situations which trigger your anger (the cause).
Then think what happened as a result of your anger (the effect).
You need to come up with some techniques to manage your anger.
Do
Give the class the anger triggers (the cause) as listed in the activity.
Put down the activity format (Anger Triggers, Result of your Anger, Anger Management Techniques) on the
board and instruct the class to write the answers under different categories.
Give the class 3‐5 minutes to think and note down their answers.
At the end of 5 minutes, ask the participants who wish to volunteer and present their answers.
Activity
Trigger points and Anger Management Techniques Activity
Anger Triggers
List of triggers that make you angry:
You get caught doing something you shouldn't have been doing.
252
26
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Say
Now, let's discuss the problems and solution with all.
The individual will first briefly describe trigger points to the class.
Then discuss the result of the anger. Other participants are requested to remain quiet while one is making the
presentation.
Post presentation, other participants may ask questions.
Do
Congratulate each individual for sharing their points.
Ask the audience to applaud for them.
Ask de‐brief questions after the presentation to the class.
Keep a check on the time. Ask the participants to wind up the activity quickly if they go beyond the given time
limit.
Ask
De‐brief questions:
In the situation described by the presenter, who was at fault?
How could you have handled this situation alternatively?
Summarize
Close the discussion by summarizing the strategies and tips of anger management for entrepreneurs.
Ask the participants what have they learnt from this exercise/ activity.
Ask if they have any questions related to what they have talked about so far.
253
27
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Ask
You are waiting in the reception for an interview or a very important meeting, suddenly your legs are shaky,
your hands are cold, you are feeling nervous. Have you ever been in this kind of situation?
Have you had days when you had trouble sleeping?
Have you ever been so worried about something that you ended up with a terrible headache?
Say
You've probably heard people say, I'm really stressed out" or "This is making me totally stressed."
Ask
What do you understand by stress?
What gives you stress?
How do you feel when you are stressed or what are the symptoms of stress?
How can stress harm you?
Why is it important for entrepreneurs to manage stress?
Say
When we feel overloaded or unsure of our ability to deal with certain challenges, we feel stressed.
Discuss about stress, causes of stress, and symptoms of stress as discussed in the Participant Handbook.
Let's understand the causes of stress and how to deal with them with the help of some case scenarios.
You will be given some cases.
You have to analyse the case scenario and then find an appropriate solution to the problem.
This will be a group activity.
Do
Divide the class into four groups of 5‐ 6 participants (depending on the batch size).
Assign one case scenario to each group.
Instruct them to read the case carefully.
The group is expected to analyse and discuss the case amongst them and find a solution to the given problem.
Explain their discussion should result in getting answers for the following questions:
254
28
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Team Activity
Case Study Analysis
Scenario 1
Akash's alarm doesn't go off and he gets late getting out of the house. He hits traffic and ends up 15 minutes
late to work, which his boss notices. He gets to his desk and finds he has to complete 2 reports in next one
hour. Just when he is about to begin work, a message pops up “Telecon with the client begins in 10 minutes.
Please be in the conference room in 5 minutes.”
His is not prepared for the call. He is stressed. He does not want to speak to his boss about this. He is stressed,
feeling uncomfortable and sick. Not in a position to attend the call or finish the reports on time.
Scenario 2
While paying his overdue bills, Rahul realised that it's the middle of the month and he has only Rs 500 left in
his account. He has already asked all of his friends, and family for loans, which he hasn't paid back yet. He is
still contemplating over the issue when his phone rings. His sister's birthday is due next week and she has
seen a beautiful dress which she wants to buy but cannot tell the parents as it is a bit expensive. She wishes if
Rahul could buy the dress for her. Rahul has promised to buy her the dress for her birthday.
Rahul is stressed, does not understand what to do. He is unable to concentrate on his work and unable to
complete the tasks assigned. His team leader has already warned him of the delay.
Scenario 3
Sheela calls the cable company as she has unknown charges on her bill. She has to go through the automated
voice mail menu three times and still can't get through to a customer care executive. After 15 minutes of
repeated efforts, her call is answered. She explains the entire issue to the customer care executive but before
the person could suggest a way out, the call drops.
Now Sheela has to call back and repeat the whole process all over again with a new customer care executive.
She is very angry and calls again but cannot connect this time.
She has to leave to office so she decides to call from office and check. When she connects this time she is
angry and argues with the executive on the call. All her co‐workers around are looking at her as her volume
has suddenly increased. She bangs the phone and ends the call.
Her co‐worker Neelam enquires what has happened to her. She ignores her and just walks off. She has
become irritable and her behaviour and tone with other co‐workers is not acceptable.
255
29
Facilitator Guide
Facilitator Guide
Scenario 4
Arpit is a young entrepreneur who started doing business through Facebook few weeks back. He had always
been into a job. Although Arpit has very few financial liabilities, it wasn't an easy decision to leave a
comfortable job at once and look for newer pastures. Arpit's boss warned him of the consequences and the
challenges of starting a business when nobody ever in his family had been in business.
He has not been able to get a good deal till now. This is an important life shift for him which comes with
unknown variables. Arpit is nervous and is wondering if he has what it takes to fulfill the requirement of his
new role, or the new experiences he's likely to face.
Ask
De‐brief questions:
What was/ were the cause(s) of stress?
Was the stress avoidable or manageable under the given circumstances?
If yes, how do you think that the stress could be avoided (managed)?
If no, then why not?
Say
Now, let's discuss the problem and solution with the larger group.
The group will first briefly describe the case to the class.
Then discuss the issue identified and the proposed solution.
Post presentation, the other groups may ask questions to the group that has presented.
Do
Congratulate each group for sharing their points.
Ask the audience to applaud for them.
Ask de‐brief questions to cull out the information from each group.
Keep a check on time. Tell participants to wind up the discussion quickly if they go beyond the given time limit.
Say
While it is common and normal to feel some tension. This feeling nervous and tensed can interfere with your
thinking process and can have a negative impact on your performance.
Stress can deplete the most vibrant of souls. It can have a negative effect on every aspect of a person's life
including their health, emotional well‐being, relationships, and career. However, one needs to understand
the causes and types of stress before looking for ways to manage it.
De‐brief:
Scenario 1
The cause of stress was lack of time management and the habit of procrastinating. If Akash would have
managed his time well, planned alternate ways to get up on time, finished prior tasks on time and planned for
client meetings in advance then he wouldn't have faced stress.
256
30
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Scenario 2
The cause of stress was lack of financial planning. Rahul should have planned his financial resources well in
advance and saved some money for the rainy day. Also, differentiating between needs and wants and
keeping a check on non‐essential expenditure would have saved Rahul from this situation.
Scenario 3
Sometimes, stress is caused due to external factors instead of internal ones. In this case, the stress was
unavoidable because we have no control over this customer care system. Every time, you will get in touch
with a new executive and will have to explain all over again. This might cause stress but despite being
frustrated and angry there is little that we can do about it. All Sheela could do was to find ways to calm herself
down through some breathing exercises and meditation, reading some good book or listening to music and
then start afresh.
Scenario 4
A positive, major life change can be a source of good stress. Regardless of how good the change is, it can be
stressful. Stress caused by a positive and major life change can be beneficial because it causes a person to
step out of their comfort zone and learn new skills. Here, Arpit may become a successful entrepreneur or
learn new ways to do things differently.
Now let us see this scenario, can I have a volunteer to read out this case to the class.
Do
Ask one of the participant who can volunteer and read out this scenario to the class.
Scenario 5
Rakesh lives in Kathmandu with his wife and two beautiful daughters Sarah and Sanya. Nepal was hit by a
massive earthquake and Rakesh's building collapsed during the earthquake. During evacuation, Rakesh
realised that though his wife and Sarah were fine and suffered only minor bruises, Sanya was nowhere in the
scene. Panic stricken, he started calling her name and searching her frantically. A little later, he heard a meek
voice from beneath the debris. He quickly removed the rubble to find a huge bed. Rakesh was pretty sure
that Sanya was trapped underneath. Though he was badly bruised, he gathered all his courage and with all
his might, he lifted the several‐ton bed to save Sanya's life. Everyone was relieved to see Sanya alive and also
extremely surprised to see this father's ability to access superhuman strength.
Ask the audience to applaud for the participant after the scenario is read completely.
Discuss the scenario, ask de‐brief questions:
What kind of stress was Rakesh undergoing in this case?
Was the stress avoidable or manageable under the given circumstances?
What was the result of the stress?
Say
De‐brief:
Not all stress is harmful; good stress is actually energizing. This was a case of lifesaving stress, or hero stress,
which is an important example of good stress. You may have heard stories in which a person performs an
impossible feat of physical strength in order to save their life or the life of someone they love. This type of
stress causing a surge of adrenaline is good for us.
257
31
Facilitator Guide
Facilitator Guide
Summarize
Close the discussion by summarizing the tips to manage stress as given in the Participant Handbook.
Ask the participants what they have learnt from this exercise/ activity.
Ask if they have any questions related to what they have talked about so far.
258
32
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Notes
259
33
Facilitator Guide
Facilitator Guide
260
34
Welding and Quality
Employability & Entrepreneurship Skills
Technician
261
35
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Computer Systems with the required applications
Say
Let's take a quick recap of the basic computer parts.
Discuss 'Basic Parts of Computer' and 'Basic Parts of a Keyboard' with the class as given in the Participant
Handbook.
Explain
Explain all the parts of the computer and the keyboard by demonstrating on the real system.
Ask
Do you know about internet?
Have you ever used internet?
Why do you think internet is useful?
What was the last task you performed on internet?
Say
Let's look at some basic internet terms.
Discuss 'Basic Internet Terms' with the participants as given in the Participant Handbook.
Summarize
Ask the participants what they have learnt from this exercise/ activity.
Ask if they have any questions related to what they have talked about so far.
Close the discussion by summarizing the importance of computer and internet for entrepreneurs.
262
36
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Practical
Conduct a practical session.
Ask the participants to assemble in the computer lab.
Give some hands on practice exercises.
Do
Group the participants for the activity depending on the batch size and the number of computer systems
available in the lab.
Explain the purpose and duration of the activity.
Ensure the participants complete the practical exercises assigned.
263
37
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Computer Systems with MS Office
Ask
What is the most frequent activity that you do on the computer?
Do you know how to make presentations on the computer?
Say
Give a brief introduction of MS Office as given in the Participant Handbook.
Discuss the most popular office products. Explain in brief their application, benefits and working.
Microsoft Word is a word processing program that allows for the creation of documents. The program is
equipped with templates for quick formatting. There are also features that allow you to add graphics, tables,
etc.
Microsoft Excel is a tool for accounting and managing large sets of data. It can also simplify analysing data. It is
also used to create charts based from data, and perform complex calculations. A Cell is an individual data box
which will have a corresponding Column and Row heading. This gives the cell a name, referred to as the Cell
Reference. There can be multiple pages in each workbook. Each page, or sheet, is called a Worksheet. When
you open a new Excel file, it automatically starts you with three worksheets, but you can add more.
Explain
Explain the working and frequently used features of Office on a real system.
Ask
What do you know about e‐mails?
Do you have an email id?
How often do you check your e‐mails?
Say
Communication is vital for every business. The fastest and the safest way to communicate these days are
through emails. MS Outlook helps to manage your emails in a better way and also offers a host of other
benefits.
Discuss “Why Choose Microsoft Outlook?” with the participants as given in the Participant Handbook.
264
38
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Do
Ask the participants to assemble in the computer lab.
Explain the working of Outlook on a real system..
Demonstrate
Demonstrate how to create email id.
Demonstrate how to write new mails, send mails.
Demonstrate how to use MS Office application to create a letter and send it as attachment in an email.
Demonstrate how to use other MS Office applications.
Practical
Give some hands on practice exercises
Group the participants for the activity depending on the batch size and the number of computer systems
available in the lab.
Explain the purpose and duration of the activity.
Summarize
Ask the participants what they have learnt from this exercise/ activity.
Ask if they have any questions related to what they have talked about so far.
265
39
Facilitator Guide
Facilitator Guide
Resources to be Used
Computer System with internet connection
Participant Handbook
Ask
How many of you have done shopping online?
Can you name at least five shopping websites?
What is the product that you most frequently buy online?
Why do you do shopping online instead of going to the market?
Say
Give a brief introduction of “What is E‐commerce”. Refer to the Participant Handbook.
E‐ commerce emerged in the early 1990s, and its use has increased at a rapid rate. Today, many companies
sell their products online. Everything from food, clothes, entertainment, furnitureand many other items
can be purchased online.
Ask
What other types of transactions have you performed on the internet other than buying products?
Say
Give examples of e‐commerce activities from Participant Handbook.
Team Activity
E‐commerce examples
Instruct the participants to list some of the payment gateways that they have used for e‐commerce activities.
Give them 5 minutes to make this list.
Discuss payment gateways and transaction through payment gateways.
Conclude the discussion by mentioning how important e‐commerce has become in our day to day
transactions.
266
40
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Say
E‐commerce activities can be classified based on the types of participants in the transaction.
Discuss “Types of E‐commerce” from the Participant Handbook.
Do
Discuss all types of E‐commerce by giving examples and names of some popular websites which use them.
Make the discussion interactive by asking the class to share some popular e‐commerce sites of each type.
Say
E‐commerce activities bring a host of benefits for both, retailers and customers.
Discuss benefits of E‐commerce from the Participant Handbook.
Explain
The majority of the population that uses E‐commerce activities lives in tier‐1 and tier‐2 cities. To encourage
the use of digital money in tier‐3 and 4 areas, PM Mr. Modi launched the “Digital India Campaign”.
Discuss “Digital India Campaign” from the Participant Handbook.
By Digital India project the government will deliver services via mobile connectivity and in doing so, is
expected to bring the internet and broadband to remote corners of the country. This connectivity will in turn
enhance e‐commerce activities also. Furthermore, the Indian Government is also modernizing India Post and
aims to develop it as a distribution channel for e‐commerce related services.
Say
Now let us discuss how to sell a product using E‐commerce.
Every product has to be sold on a platform on the internet. Think of it as a shop that you have to sell your
product. Now this shop can be your own or shared or rented. If the shop is your own or rented there will be
only your products in that shop. If the shop is shared, there will be products of multiple sellers in that shop. A
common example is a departmental store which has products from multiple brands in the shop.
Similarly, in E‐commerce the shop is the website where your products are displayed. If it is your own website it
will exclusively showcase your products. In this case the cost that you will incur will be:
Developing the website
Hosting the website
Maintenance of the website
If you rent a website it will also showcase your own products but the development, hosting and maintenance
parts goes to the owner. This saves time and the cost to manage these activities.
Smaller companies usually go for renting a website and the bigger ones develop their own website.
The concept of shared platforms has become very popular in recent times. In this platform the sellers have to
register and then they can sell their goods on a common platform. Among the most popular of these are
Amazon, Myntra, Flipkart, etc.
Role Play
Tell the participants to choose a product or service that they want to sell online.
Tell them to write a brief note explaining how they will use existing e‐commerce platforms, or create a new e‐
commerce platform to sell their product or service.
267
41
Facilitator Guide
Facilitator Guide
Ask
How much money are you carrying in your wallet?
Do you have a credit/debit card?
How do you make payments while doing online shopping?
Say
Demonetization has made carrying cash in the wallet very difficult. People either shop through cards or some
other form of digital money.
So what do you think is digital money?
In this form the money is both paid and received digitally. There is no hard cash involved. It is an instant and
convenient way to make payments.
There are various types of digital payments. Let us discuss some of them in brief here.
The first one is the most commonly used system i.e. the cards. Debit card, credit card, prepaid card, all fall
under this category.
Then is the e‐wallet or the mobile wallet. This has become the most used form of digital money after
demonetization. Examples are Paytm, state bank buddy, Freecharge, etc.
Many other forms of digital money are also coming up in market like mobile apps, Aadhar card based
payment, etc.
Do
Demonstrate how to make and receive payments through digital models like Paytm and state bank buddy.
Ask
Why do you think people have started using digital money instead of hard cash? Is demonetization the
only reason?
Say
Digital money gives a lot of advantages over the conventional hard cash. Some of them are:
Digital payments are easy and convenient. You do not need to take loads of cash with you, a mobile
phone or a card will suffice.
With digital payment modes, you can pay from anywhere anytime.
Digital payments have less risk.
Summarize
Ask the participants what they have learnt from this exercise/ activity.
Ask if they have any questions related to what they have talked about so far.
Close the discussion by summarizing the importance of e‐commerce and digital money.
268
42
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Notes
269
43
Facilitator Guide
Facilitator Guide
270
44
Welding and Quality
Employability & Entrepreneurship Skills
Technician
271
45
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Ask
How many of you save money?
Why do you feel the need to save it?
Do you plan your savings?
Where do you keep the money you save?
How do you use the money that you have saved?
Example Example
Example 1:
Suhani works in a good company and earns Rs.30, 000 month. She always saves 5000 per month and keeps it
aside as a personal saving. She keeps the money at home and has saved quite a lot. One day her mother has a
medical emergency and has to be taken to the hospital. Her family is worried about the amount they have to
spend for the treatment. It will cost them atleast 40,000.
Suhani says tells her family not to worry and that she has about 50,000, which she has saved over the months.
Example 2:
Jasmeet works in the same company and earns the same as Suhani. She is very fond of shopping and spends
most of her money on buying new clothes. At the end of the month, she is always asking her father for money
as her pay is finished.
Ask
Who do you identify with –Suhani or Jasmeet ?
How do you think Suhani manages to save money which Jasmeet is unable to do?
Say
We should always set aside some and save some money from our monthly pay. The future is unpredictable.
Saving money not only gives you a sense of financial security but it can be used in case of emergencies.
Discuss “Importance of Saving” with the participants as given in the Participant Handbook.
Ask
What are the benefits of saving money?
What does being financially independent mean to you?
272
46
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Say
Discuss “Benefits of Saving” with the participants as given in the Participant Handbook.
Now let us continue with Suhani's story. Suhani has told her family not to worry and that she has about
50,000, which she has saved over the months. The family is happy about Suhani's decision of saving money,
which will be of great help for them now.
Suhani is going to the hospital today to pay the first instalment for the treatment. Suddenly finds only 35,000 in
her cash box when she counts and does not remember using it. She has not kept any record and now she is upset.
Ask
Was it a good decision by Suhani to save a part of her earnings every month?
Was it a wise decision to keep all her savings as cash in a cash box?
Could she have managed to save money in a better and more effective manner?
Do you want to learn how to save money and use it effectively?
Say
Let's learn personal saving with the help of a group activity.
Team Activity
Personal Finance‐ Why to save
This activity has two parts:
PART 1
WAYS TO SAVE MONEY
You are earning 30,000/‐ per month. You have recently changed your job and have to move to a
metropolitan city. You are now living as a paying guest paying 10,000/‐ per month. Your other estimated
expenditures like travel, food, recreation would be around Rs. 17, 000 per month.
Make a list of different ways to save money.
PART 2
HOW WILL YOU USE THE MONEY
After a year how much have you been able to save?
How will you use the money that you have saved?
Do
Divide the class into groups of four.
Instruct the participants to think and prepare a list of the various ways they can save money.
Give the participants 10 minutes to prepare the list.
Once done, instruct them to think of how they could use the money they have saved.
Give the participants 10 minutes to prepare the list.
Keep a check on time. Tell the group to wind up quickly if they go beyond the given time limit.
Activity De‐brief
What were the different ways you could save money?
How much money were you able to save?
How will you use the money you have saved in one year?
273
47
Facilitator Guide
Facilitator Guide
Say
Discuss the importance of personal finance and why it is important to save money.
Summarize
You can summarize the session by discussing:
The importance of saving money.
Ways to save money.
How the money saved can be used for different purposes.
274
48
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Resources to be Used
Account opening sample forms
Participant Handbook
Ask
How many of you save money?
Where do you keep the money you save?
How many of you have a bank account?
What type of account do you have?
Example Example
Reena is in the third year of college but in the evening she gives tuitions for children living in her colony. She
earns 15,000/‐ per month. As her students stay in different parts of the city, she has to walk a lot.
To save time, she decides to buy a second hand scooter for herself. But she has to save money for it. Her class
mate advises her to open a recurring deposit account in the bank.
She goes to the bank close to her home. The personal manager gives her some forms to fill. She is confused
as she has never done this before. Her elder sister has an account in the same bank. She asks for help from her
sister. She goes to the bank the next day with her sister. The personal banker gives her a list of documents that
she will need to submit with the form for opening an account. The banker advises her to open a 6 months
recurring deposit.
Ask
Do you try to save money monthly but have to spend it on unforeseen expenditure?
Have you ever thought of depositing your savings in a bank?
Say
Before opening a bank account, you need to know the types of accounts we have in India.
Discuss “Types of Bank Accounts” with the participants as given in the Participant Handbook.
Ask
Can someone say what are the different types of bank accounts?
275
49
Facilitator Guide
Facilitator Guide
Say
Let's learn about the different types of bank accounts through an activity.
Team Activity
Divide the class in four groups.
Label the groups as savings account, current account, recurring account and fixed deposit.
On a chart paper, ask them to write the key points of their account.
Activity De‐brief
Ask each group to present the key points of their account.
Say
Now that you know about the four different types of accounts, let's learn how to open a bank account.
Discuss “Opening a Bank Account” with the participants as given in the Participant Handbook.
Discuss “Tips” that the participants should keep in mind while opening a bank account as given in the
Participant Handbook.
Ask
What are the main documents required for opening a bank account?
What are some important points to ask the bank personnel while opening an account?
Say
Mention officially valid KYC documents (refer to the Participant Handbook)
Now, let's understand the procedure of opening a bank account through an activity.
Team Activity
Opening a Bank Account
This activity is done in groups.
Divide the class in groups of four or six.
PART 1
FILLING A BANK ACCOUNT OPENING FORM
You have to fill a bank opening form.
You can refer to the section “Opening a Bank Account” of your Handbook for reference.
List all the steps that you will be required to fill in the form.
List the documents that you needs for filling the form.
Now fill in the form.
Activity De‐brief
How did you design the form?
What all details did you fill in the form?
What were your KYC documents?
How would this activity help you in future?
276
50
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Do
Instruct the participants to read the section “Opening a Bank Account' of the Participant Handbook.
Give each group one sample account opening form.
Give the participants 5 minutes to read the form.
Give them 15 minutes to fill it.
Assist them by explaining each category and how to fill it.
Keep a check on time.
Tell the group to wind up quickly if they go beyond the given time limit.
Summarize
Note:
You can summarize the unit through a role play.
A person wanting to open an account in the bank.
What is the procedure that he will go through?
Discuss the key points of different types of bank accounts.
How to select the type of account
How to fill the account opening form.
A sample account opening form is given in the following page for reference. Use it for the activity in the class.
Sample Bank Account Opening form.
XXX Bank
Photograph
277
51
Facilitator Guide
Facilitator Guide
278
52
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Resources to be Used
Participant Handbook
Blank sheets of paper
Pens
Ask
What is cost?
Will a telephone bill fall under the category of a fixed or variable cost?
Say
Discuss: Fixed and Variable cost with examples.Let us do a small activity.
Team Activity
Identify the type of cost
1. Rent
2. Telephone bill
3. Electricity bill
4. Machinery
5. Insurance
6. Office supplies/ Raw materials
7. Employee salaries
8. Commision percentage given to sales person for every unit sold
9. Credit card fees
10. Vendor bills
Do
Divide the class into two groups. Read out the list of costs given in the activity.
Read out each item from the cost list and ask the groups in turns to identify whether it is a fixed or variable
cost.
279
53
Facilitator Guide
Facilitator Guide
Say
We saw that your utility bills like rent, electricity, telephone etc. are all fixed costs because you have to pay it
every month.
Variable costs is an expense which varies with production output or volume. For example commission, raw
material etc.
Discuss “Cost: Fixed vs. variables” with the participants as given in the Participant Handbook.
Illustrate the relation between the costs with a graph.
Total Costs
`
Variable Costs
Fixed Costs
Units
Let's learn the difference between fixed and variable cost with the help of an activity.
Team Activity
Fixed vs. Variable Costs
This is a group activity.
Activity De‐brief
What is the total cost of your business?
What are the fixed costs?
What are the variable costs?
How did you differentiate between the fixed and variable costs?
Do
Instruct the participants that this is group work.
Divide the class into small groups of 4 or 6.
Give each group a sheet of paper.
Tell the participants that they have to start their own entrepreneur business.
Ask them the type of business they want to start.
Instruct them to differentiate between the fixed and the variable costs of the business they want to start.
Give the participants 15 minutes to discuss and write.
Keep a check on time. Tell the group to wind up quickly if they go beyond the given time limit.
280
54
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Summarize
Note: You can summarize the unit either by having a role play between a consultant and a budding
entrepreneur explaining the differences between fixed and variable costs or by discussing the key points of
the unit.
281
55
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Ask
Ask the participants‐ “What do you see first thing in when you get your mobile bill? Apart from the amount
and due date do you have a look at the taxes you are being billed for?
Why do you think people get their cars insured or have a medical insurance?
You have saved money and want to invest it, how would you decide what is the best investment for your money?
Example Example
Ranbir has sold his house and deposited the money in his bank. His Chartered Accountant tells him that he
will have to re‐invest the money otherwise he will have to pay capital tax. What is capital tax and how is it
different from income tax?
Jasmeet and Anup are blessed with a baby girl. They decide to have an insurance policy that will mature
when their daughter is ready to higher education.
Shivani is working in a corporate office and getting good pay. She will have to pay income tax so she decides to
invest her money in tax saving schemes. She goes to the bank manager to discuss the best products in which
she can invest.
Say
Discuss the Investment, Insurance and Taxes as given in the Participant Handbook.
Ask
How do investments, insurances and taxes differ from each other?
Say
Let's learn the differences between the three by having an activity.
Say
We will have a quiz today.
282
56
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Team Activity
The activity is a quiz.
Do
Divide the class into groups of three and give a name to each group
Explain the rules of the quiz. For each correct answer the group gets 1 mark. If the group is unable to answer
the question is rolled over to the next group.
Explain the purpose and duration of the activity.
On the blackboard write the names of the groups.
Ask the questions of the quiz.
Keep a score for the groups.
Set guidelines pertaining to discipline and expected tasks.
Summarize
Summarize the unit by discussing the key points and answering question
283
57
Facilitator Guide
Facilitator Guide
284
58
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Resources to be Used
Participant Handbook
Computer System with internet connection
Debit card
Ask
When was the last time you visited a bank?
How do you pay your bill for electricity and telephone?
Have you ever tried to transfer money from one bank account to another bank account using the online
banking facility?
Say
Most of us lead a busy life. Time has become more important than money. In this busy schedule no one has
time to stand in bank queues. That's where Online Banking comes in. Online banking or internet banking
means accessing your bank account and carrying out financial transactions through the internet.
Discuss “What is online banking?” from the Participant Handbook.
There are various advantages of online banking:
It saves time, as you need to visit the branch. .
You can conduct your banking transactions safely and securely without leaving the comfort of your
home.
Online Banking also gives you round the clock access.
Online Banking makes it possible for you to pay your bills electronically.
Do
Show them how they can use the internet banking.
Use the computer system and show the demo videos on how to use internet banking provided on most
banking sites. the computer system.
Tell the class the various features of online banking:
Through their website set‐up your online account.
Choose a secure username and password.
Set‐up your contact information.
Once your information is verified, you are good to go.
Once you enter the portal explore all the features and learn your way through the portal.
Discuss about maintaining the security of the online account.
285
59
Facilitator Guide
Facilitator Guide
Say
One of the biggest advantage that online banking offers, as discussed earlier, is transferring money from one
account to another. This transaction is called electronic funds transfer. Electronic transfers are processed
immediately with the transferred amount being deducted from one account and credited to the other in real
time, thus saving time andeffort involved in physically transferring a sum of money.
Discuss “Electronic Funds Transfer” from the Participant Handbook.
Do
Discuss how to transfer money from one account to another using online banking (NEFT/ RTGS, etc.).
Illustrate with an example.
Summarize
Close the discussion by summarizing the about online banking.
Ask the participants if they have any questions related to what they have talked about so far.
286
60
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Notes
287
61
Facilitator Guide
Facilitator Guide
288
62
Welding and Quality
Employability & Entrepreneurship Skills
Technician
289
63
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Ask
Have you ever attended an interview?
How did you prepare before going for an interview?
Say
An interview is a conversation between two or more people (the interviewer(s) and interviewee) where
questions are asked by the interviewer to obtain information from the interviewee.
It provides the employer with an opportunity to gather sufficient information about a candidate and help
them select the ideal candidate.
It also provides the interviewee with an opportunity to present their true potential to the employer, build
confidence and help make a decision about the job by asking questions regarding designation, salary, perks,
benefits, promotions, transfers, etc.
Let's do an activity to understand how to prepare for interviews better.
Activity 1
Introducing Yourself
Do
Select a participant and ask him/her to answer the following questions: “What can you tell me about yourself.”
Give the participant at least one minute to speak.
Once he/she is done, ask the rest of the participant what they gathered about the participant who was
providing information.
Now repeat the exercise with five other participants.
Ask
What information you should include when you are describing or introducing yourself in an interview?
What information you should not include when you are describing or introducing yourself in an interview?
290
64
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Say
Tell the participants that when an interviewer asks you to say something about yourself, he/she is not asking
you to present your life history.
Introduction should be short and crisp, and should present you in a positive light. It should include the
following points:
Any work experience that you might have
A brief summary of your educational qualifications
Your strengths and achievements
Any special projects that you might have been part of
The following topics should be avoided during an introduction:
Detailed description of your family (unless you are specifically asked to do so)
Too much information about your weaknesses
Information that is not true
Do
Congratulate each participant for sharing their points.
Ask the audience to applaud for them.
Ask de‐brief questions to cull out the information from each group.
Keep a check on time.
Activity 2
Planning the right attire
Do
Describe 2 individuals to the participants. One is wearing a casual t‐shirt, jeans, and slippers. He has not
combed his hair and neither has he trimmed or shaved his beard. The other individual is dressed formally with
a shirt and pant, and is well‐groomed. He has also worn formal shoes and a belt. Ask the participants which
person would they prefer to hire in their organization and why?
Summarize
Close the discussion by discussing 'how to prepare for an interview' as discussed in the Participant Handbook.
You can add the following points to it:
Tell the participants to create a positive and good impression in an interview. It is important for them to
prepare for an interview beforehand.
The interviewer analyses not only your technical knowledge in relation to the job, but also whether or
not you are a fit for the organization.
Every employer looks at the whole package and not just one or two things in isolation. Therefore, the way
you dress and the way you present yourself is also important along with your skills and talents.
The participants will get only one chance to create a good first impression.
291
65
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Blank papers
Pens
Ask
When preparing for an interview, what are the most important things that you need to do?
What documents do you carry with you, when you go for an interview?
What is a resume?
Why do you need a resume?
Say
Resume is not just a sheet of paper with your qualifications printed on it.
It is a selling tool that will help the employer to see how and what you can contribute for company.
Talk about the steps involved in creating an effective/attractive resumes discussed in the Participant Handbook.
Now let's prepare a resume to understand the process in a better way.
Do
This is an individual activity.
Give the details of the activity.
Instruct them to read the activity carefully.
The participant is expected to make an attractive resume based on the information provided.
Give the class 25‐30 minutes to study the case and create a resume.
At the end of 30 minutes, the participants should exchange the resume with the person sitting next to him or her.
Every participant will evaluate the resume prepared with their fellow participants.
Say
Do you think the candidate should apply for the job posting described in the advertisement?
We have already discussed the steps involved in creating an effective/attractive resumes.
Now let's prepare a resume for the candidate details given in the activity.
292
66
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Activity
Case Study Analysis
In the first section of the activity, you are being given the information about a candidate who is applying
for a particular job.
In the second section, you are being given the detailed description of the job posting. Create a resume for
the candidate to apply for the job posting.
Use the information that has been provided about the candidate to create this resume.
Candidate Details
Nipesh Singla was born on 20th April, 1988 in Chandigarh, India. He currently resides at 1XX7, Sector XX D,
Chandigarh –160018. His mobile number is 988XXXXX01, and e‐mail address is [email protected].
Nipesh attended middle and senior school at Government Boys Senior Secondary School, Sector 15,
Chandigarh. He has been a very talented boy since school. He was fond of painting and watching old Hindi
movies. As part of a school charity program, he volunteered at the children's hospital during his senior years.
In July 2007, he joined Westwood School of Hotel Management, Zirakpur to pursue a diploma course in Hotel
Management and Catering. After completing this course, he joined XYZ Group of Hotels as a Housekeeping
intern in June 2010 for six months. In this role, he was responsible for cleanliness and maintenance of one
floor in the hotel. Taking advantage of his strong interpersonal skills, he also got opportunities to make
housekeeping arrangements for corporate meetings. While pursuing education, he gained working
knowledge of Microsoft Word, Excel, Access and PowerPoint.
Nipesh is detail‐oriented, flexible and adaptable. He has successfully worked with a diverse work force. He
gelled well with his peers, both in college and during his internship. After completing the internship, his
objective has been to find a job opportunity where he can use his skills and experience. Backed by
experience, he is confident about his skills as housekeeping assistant.
Job Posting
* Do you see yourself as a HOUSEKEEPING SUPERVISOR?
What's your passion? Whether you're into cricket, reading or hiking, at IHG we are interested in YOU. At IHG,
we employ people who apply the same amount of care and passion to their jobs as they do in their hobbies ‐
people who put our guests at the heart of everything they do. And we're looking for more people like this to
join our friendly and professional team.
THE LOCATION:
At the moment, we are looking for HOUSEKEEPING SUPERVISOR to join our youthful and dynamic team at
Holiday Inn Amritsar, Ranjit Avenue in Amritsar, Punjab (India). Holiday Inn Amritsar is ideally located in
Amritsar's commercial district on Ranjit Avenue with the world famous Golden Temple located only a short
distance away. Sparkling chandeliers mark an incomparable arrival experience as you escape to the
welcoming environment that is, Holiday Inn Amritsar. The fresh international brand to celebrate and explore
Amritsar.
Salary: Negotiable
Industry: Travel / Hotels / Restaurants / Airlines / Railways
Functional Area: Hotels , Restaurants
Role Category: Housekeeping
Role: Housekeeping Executive/Assistant.
Desired Candidate Profile
Friendly, pleasant personality, Service ‐ oriented.
You should ideally be Graduate/ Diploma holder in HM and at least 2 years of experience as a supervisor in
good brand with good communication skills, English is a must.
293
67
Facilitator Guide
Facilitator Guide
In return we'll give you a competitive financial and benefits package. Hotel discounts worldwide are available
as well as access to wide variety of discount schemes and the chance to work with a great team of people.
Most importantly, we'll give you the room to be yourself.
*Please get in touch and tell us how you could bring your individual skills to IHG.
Education‐
UG: Any Graduate/ Diploma holder
PG: Post Graduation Not Required
Say
Now, let's share the resume with the fellow participant sitting next to you and evaluate each other's effort.
Do
Congratulate each participant for making their first attempt towards creating an effective resume.
As a follow up activity, you can suggest them to prepare their own resume and show it to you the next day.
Summarize
Close the discussion by showing some effective resume samples to the candidates.
Ask the participants what they have learnt from this activity.
Ask if they have any questions related to what they have talked about so far.
Nipesh Singla
#1XX7, Sector XX‐D
Chandigarh‐160018
Mobile No: 91‐988XXXXX01
E‐mail: [email protected]
Objective: Seeking an opportunity to use my interpersonal skills and experience to contribute to your
company's growth, profitability and objectives.
Professional strengths:
Proficient in housekeeping
Experienced in and capable of working with a diverse work force
Team player and friendly in nature
Successful working in a multi‐cultural environment
294
68
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Educational background:
Diploma in Hotel Management and Catering, Westwood School of Hotel Management, Zirakpur
High School, Government Boys Senior Secondary School, Sector 15, Chandigarh
Professional internships:
Housekeeping Intern, XYZ Group of Hotels, New Delhi (June 2010 – August 2010)
Responsible for cleanliness and maintenance of one floor in the hotel.
Got opportunities to make housekeeping arrangements for corporate meetings.
Volunteer Work:
Student volunteer at children's hospital in Chandigarh.
Nipesh Singla
295
69
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Say
Tell the participants you will provide them with interview situation and questions and they have to try to
answer them.
Tell them you will also explain the different ways to approach these questions.
Do
Divide the class in pairs and ask the participants to perform a role play.
One partner will play the role of the interviewer while the other will play the role of the interviewee.
Tell them the interviewer can start the interview by asking the interviewee to introduce himself/herself.
Call all the pairs one by one in front of the class to enact the role play.
Follow the same pattern for all other situations.
Time allotted for each situation is 8‐10 minutes.
Congratulate each participant for giving their input.
Ask the class to applaud each time a team has completed their role play.
Keep a check on time.
Role Play
Conduct a role play for the situation given.
Situation 1
The interviewer will start by asking the interviewee a few generic questions such as:
What is your name?
Tell me something about yourself?
Can you tell me something about your family?
Then, the interviewer will bluntly ask the following questions:
How do you explain this huge time gap in your resume?
What is the reason for this?
Weren't you looking for a job or is it that no one selected you?
296
70
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Say
De‐brief:
When you put information on your resume, you should be prepared to answer any questions about it.
Be present and focused on the questions being asked to you.
One way of tackling the blunt questions is to tell the interviewer you did not come across an opportunity
where you were sufficiently satisfied with both the remuneration offered as well as the profile. Therefore,
you waited for the right opportunity to come along while looking for an ideal job.
Role Play
Conduct a role play for the situation given.
Role Play – Situation 2
The interviewer will start by asking the interviewee a few generic questions such as:
What is your name?
Tell me something about yourself?
Can you tell me something about your family?
Then, at the end of the interview, ask the interviewee:
There are over 200 people who have applied for this job, some with excellent work experience. Why
should I hire you?
Say
De‐brief:
There is nothing wrong with stating your strengths and achievements. However, do not come across as
arrogant or too boastful.
You need show the interviewee that you have unique skills or talents to contribute to the company. The
interviewer needs to know how you stand apart from the rest of the crowd.
Tell the interviewer you are looking forward to working with the company and that you are a hard‐working
individual.
Role Play
Conduct a role play for the situation given.
Role Play – Situation 3
The interviewer will start by asking the interviewee a few generic questions such as:
What is your name?
Tell me something about yourself?
Can you tell me something about your family?
Then, lean forward, clasp your hands on the table and in a soft voice ask the interviewee:
Did you ever experience any neglect or disregard from your previous office? In other words, did you ever
suffer because your office or team displayed favouritism?
Say
De‐brief:
Keep this in mind: Do not criticize anyone during an interview.
You are free to express your opinion, however, your language, answers, body language, and the tone of your
voice should remain constructive and neutral.
Since criticism will show you in negative light, you should keep your answers honest yet diplomatic.
You can tackle such questions by saying, “I got along well with most of my faculty and peers.”
297
71
Facilitator Guide
Facilitator Guide
Role Play
Conduct a role play for the situation given.
Role Play – Situation 4
The interviewer will start by asking the interviewee a few generic questions such as:
What is your name?
Tell me something about yourself?
Can you tell me something about your family?
Then very bluntly ask the interviewee:
How long do you plan to stay with this company if you are selected?
After the candidate responds, ask sarcastically:
Do you seriously mean that?
Say
De‐brief:
Don't provide unreal and idealistic answers.
Your answers should be honest yet diplomatic. In a situation like this, the interviewer does not expect you to
provide a specific timeline.
You can say something like, “I would like to stay with the company as long as I can contribute constructively
and develop as an employee, within the organization, professionally and financially.”
Role Play
Conduct a role play for the situation given.
Role Play – Situation 5
The interviewer will start by asking the interviewee a few generic questions such as:
What is your name?
Tell me something about yourself?
Can you tell me something about your family?
Ask him/her how important he/she thinks it is to be punctual in the corporate world.
After he/she answers, look up sternly at the interviewee and in a crisp voice, say:
You were late for this interview by 10 minutes. That surely does not seem to be in line with what you just
said?
Say
De‐brief:
Politely apologize for being late.
You can add something such as, “I assure you this is not a habit”. All your future actions should be in line with
this statement.
Avoid giving any excuses.
You might feel obligated to provide a justification for your tardiness, but the interviewer is not interested in
that.
Do not over apologize. Once this response is out of the way, turn your focus back to the interview.
298
72
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Role Play
Conduct a role play for the situation given.
Role Play – Situation 6
The interviewer will start by asking the interviewee a few generic questions such as:
What is your name?
Tell me something about yourself?
Can you tell me something about your family?
After asking a few academic or job‐related questions, ask the interviewee:
If you get this job, what salary package do you expect us to give you?
Say
De‐brief:
If there is no way for you to avoid this question, respond to the interviewer by providing a reasonable and
well‐thought out salary range.
Role Play
Conduct a role play for the situation given.
Role Play – Situation 7
The interviewer will start by asking the interviewee a few generic questions such as:
What is your name?
Tell me something about yourself?
Can you tell me something about your family?
Then, bringing the interview to a close, ask the interviewee:
Do you have any questions for me?
Say
De‐brief:
Ask relevant questions.
Don't bombard the interviewer with questions.
If you have questions about the result of the interview, you can limit your questions to 1 or 2. Keep them short
and relevant like:
When will I be informed about the results of the interview?
What are the working hours?
Will the job require me to travel?
Explain
Tell the participants to be prepared for answering different types of questions in an interview.
Stay calm and focused, and take a moment to think about how you should respond. Always maintain a
confident tone.
Even if you don't intend to, your body language conveys your level of discomfort with a particular question.
Try to keep your actions, tone, and gestures neutral.
Maintain your composure while answering personal question.
299
73
Facilitator Guide
Facilitator Guide
Do
Tell all the participants to form pairs again.
Tell them to use the following list of frequently asked interview questions to conduct mock interviews.
They will use all or some of these questions to conduct mock interviews with their partners.
One partner will play the role of the interviewer while the other will play the role of the interviewee.
After they are through asking and answering the questions, the roles will be reversed.
The same list of questions will be used again.
After each mock interview ask the interviewer to provide feedback and clear any doubts that may arise.
Time allotted for each situation is 30‐35 minutes.
Activity
Mock Interview Questions
Mock Interview Questions
Summarize
Close the discussion by discussing the questions in the both activities.
Ask the participants what they have learned from this activity.
Ask if they have any questions related to what they have talked about so far.
300
74
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Resources to be Used
Participant Handbook
Chart papers
Blank sheets of paper
Pens
Ask
What do you understand by workplace terminology?
Are offer letter and contract of employment the same?
Say
Let's start this unit with an activity.
Team Activity
Workplace terminology
This is a group activity conducted in three parts.
Part 1
Sheila received a call from the recruiter of MND Company. Before she is recruited by the company, think of
the recruitment process she will have to go through. Start from the telephone call to signing her letter of
acceptance. Write down all the words that come to your mind.
Activity De‐brief
Have the participants read out the words they have written
Encourage all the participants to participate in the activity
Do
Divide the class into small groups of 4 or 6.
Instruct the participants that they will be doing a brainstorming activity.
Give them one chart paper each. Tell them to divide the chart in two parts.
Instruct them that they have to use one half of the chart paper now. The other half will be used later.
The participants have to write all the words that come to their mind related to the recruitment process.
Give them 10 minutes to do the activity.
Tell them that there are no right or wrong answers.
Keep a track of the time.
301
75
Facilitator Guide
Facilitator Guide
Say
You all know quite a few words related to the terms used in the office.
Let us talk about some new terms that have been missed out.
Discuss “Work Readiness – Terms and Terminology” with the participants as given in the Participant Handbook.
Ask
Why is it important to know the workplace terms?
How do they help?
Can the words be categorised further?
Say
Let's now continue the activity.
Team Activity
Terms and Terminology
This is again a group activity. The members of the group remain the same as in Activity 1.
Part 2
With the help of the new terms you have learned, make a flow chart of the hiring process of MND Company.
Activity De‐brief
Ask the groups to share the flow charts and the new terms they added while preparing the flow chart.
Do
Instruct the participants that they have to use the 2nd half of the same chart they had used before.
Using the new terminology and the terms they had previously written on the chart, they have to make a flow
chart of the hiring process of the MND Company.
Give them 10 minutes for this activity.
Keep a check on time. Tell the group to wind up quickly if they go beyond the given time limit.
Say
Let's go ahead with the activity.
Team Activity
Terms and Terminology
The activity continues with the same group members.
Part 3
Sheila now works for the MND Company. She is not aware of the company culture and policies. She goes to
the HR Department to get her doubts clarified. Can you think of the terms for which she wants clarity? Make
a list of those words.
Activity De‐brief
Ask the groups to share their list of words. Some of the words are benefits, comp. time, deduction, employee
training, holidays, lay‐off, leave, maternity leave, mentor, notice, paternity leave, and time sheet.
302
76
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Do
Instruct the participants to identify the key terms an employee of a company should know. They can use the
same chart paper for this activity.
Give them 5 minutes for this activity.
Keep a check on time. Tell the group to wind up quickly if they go beyond the given time limit.
Summarize
Note: You can either summarize the key points of the unit or have a role play where an employee has just
joined a company and the HR Manager explains the terms of employment.
303
77
Facilitator Guide
Facilitator Guide
304
78
Welding and Quality
Employability & Entrepreneurship Skills
Technician
305
79
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Say
Let's start this session with some interesting questions about Indian entrepreneurs.
Team Activity
Quiz Questions
1. Who is the founder of Reliance Industries?
Dhirubhai Ambani
2. Who is the Chairman of Wipro Limited?
Azim Premji
3. Who launched e‐commerce website Flipkart?
Sachin Bansal and Binny Bansal
4. Who is the founder of Paytm?
Vijay Shekhar Sharma
5. Who is CEO of OLA Cabs?
Bhavish Aggarwal
6. Who is the founder of Jugnoo?
Samar Singla (autorickshaw aggregator)
7. Who is the founder of OYO Rooms?
Bhavish Aggarwal
Do
Tell them that you will ask them few questions about a few entrepreneurs.
Divide the class in to two groups.
In turns ask the quiz questions to the groups.
If the answer is incorrect pass the question to the other group.
Share the answer if the groups are not able to answer.
Congratulate the participants who answered correctly.
306
80
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Ask
What do you understand by entrepreneurs?
What is the importance of entrepreneurship in today's scenario?
What do you think are the characteristics of successful entrepreneurs?
What are different types of enterprises that an entrepreneur in India can own and run?
Say
Talk about entrepreneurs, importance of entrepreneurship, characteristics of successful entrepreneurs, and
different types of enterprises in India as discussed in the Participant Handbook.
Tell the participants, stories of successful Indian entrepreneurs‐ their struggles, the moments of heartbreak,
the perseverance and triumph.
Ask them if they know of any such entrepreneur.
Summarize
Close the discussion by summarizing about the opportunities for entrepreneurs in India.
307
81
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Blank sheets of paper
Pens
Do
Show the picture given below to the class.
Ask them to quickly write on a piece of paper what comes to their mind after seeing the picture.
Now ask them, “What do you understand from this picture?”
Encourage participants to share their thoughts.
Say
This picture depicts the qualities of a leader and the difference between a leader and a boss.
A boss focuses on structure and inspires fear whereas a leader follows vision and generates enthusiasm.
A boss blames employees for the breakdown whereas a leader fixes breakdowns.
A boss depends on authority whereas a leader depends on goodwill.
A boss says “I” and a leader says “We.”
A boss drives employees whereas a leader coaches them.
A boss takes credit whereas a leader gives credit.
Say
Talk about leadership and leadership qualities for an entrepreneur as discussed in the Participant Handbook.
Ask
Why is it important for a leader to be effective? How does it help the organization?
308
82
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Say
Let us discuss benefits of effective leadership as discussed in the Participant Handbook.
“Out‐of‐the‐box thinking” is one of the new leadership styles. It means thinking differently and from a new
perspective.
Ask
Do you consider yourself a team player?
Team Activity
Long Chain
This is a group activity.
Do
Divide the class into 2 teams.
Ask each team to create a chain using materials they have in class such as shoe laces, belts, paper,
handkerchief, ribbons, etc.
The team that creates the longest chain wins the game.
Observe if the participants are interacting with their team or working in isolation.
Share your observations with the class.
Say
De‐brief:
What did the winning team do differently?
Who was responsible for the winning team's success?
How does this activity explain the role of teamwork in entrepreneurial success?
Say
Tell the class that both the teams performed well.
Discuss that the objective of this activity was to open communication channels and how this has been
achieved.
The participants should aim to keep the communication channels open when interacting with their peers and
team members.
It will set the pace and enthusiasm required for all the ensuing teamwork activities.
Talk about teamwork and importance of teamwork in entrepreneurial success as discussed in the Participant
Handbook.
Summarize
Close the discussion by summarizing about the importance of teamwork for employees.
Teamwork helps in reducing stress for the employees.
Teamwork helps employers in generating more number of solutions to a problem and developing
improved communication amongst employees.
Ask the participants what they have learned from these exercises.
Ask if they have any questions related to what they have talked about so far.
309
83
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Activity 1
Activity – Chinese Whisper
Step 1: Form a circle.
Step 2: Start a whisper chain. Any one participant will whisper a message into his/her neighbour's ear. No one
else must hear the message. The message can be serious or downright silly.
Step 3: The next person who first heard the message should whisper the message very quickly to the person
sitting next to them.
Step 4: The game goes on until the last person says whatever they heard out loud and the first person reveals
the real message.
Compare them and have a great laugh!
Ask
De‐brief questions:
Was the original message the same as the message that is communicated at the end of the game?
Why do you think there was a difference in the messages?
Say
No, the original message was not same at the end of game.
The barriers to communication like language, disturbance and noise, poor listening skills, boredom, poor
speaking skills, etc. are the potential reasons this happens.
There are various aspects to communication. Speaking skills and listening skills are two major components to
any communication. There is always some room for improvement in the way we communicate.
It is important to accept the reality of miscommunication and work to minimise its negative impacts.
310
84
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Say
Communication is a two‐way process where people exchange information or express their thoughts and
feelings
It involves effective speaking and effective listening.
If I go to the store to get bread, I exchange money for the bread. I give something and get something in return.
Communication takes place in the same manner. You have to provide and receive information for
communication to take place.
Ask
How often do you hear these statements?
“You're not listening to me!”
“Why don't you let me finish what I'm saying?”
“You just don't understand!”
What do you think the other person is trying to convey to you through these sentences?
We will not talk about the importance of listening effectively as discussed in the Participant Handbook.
Say
Let's play a game to understand effective listening process better.
Do
This is a class activity.
The participants need to answer the questions they hear.
Instruct them to listen carefully.
You will read it at a stretch and if need be repeat it once more.
Tell the participants to raise their hand if they know the answer to the question asked.
Keep a check on time.
Activity 2
Riddles:
Is there any law against a man marrying his widow's sister?
If you went to bed at eight o'clock at night and set the clock's alarm to ring at nine o'clock, how many hours of
sleep would you get?
Do they have a 26th of January in England?
If you had only one match and entered a dark room that had a kerosene lamp, oil heater, and a wood stove,
what would you light first?
The Delhi Daredevils and the Chennai Super Kings play five IPL matches. Each wins three matches. No match
was a tie or dispute. How is this possible?
There was an airplane crash. Every single person died, but two people survived. How is this possible?
If an airplane crashes on the border of two countries, would unidentified survivors be buried in the country
they were travelling to or the country they were travelling from?
A man builds an ordinary house with four sides except that each side has a southern exposure. A bear comes
to the door and rings the doorbell. What is the colour of the bear?
311
85
Facilitator Guide
Facilitator Guide
Answers:
There's no law against a man marrying his widow's sister, but it would be the neatest trick in the book since to
have a widow, the man would have to be dead.
You'd get one hour's sleep since alarm clocks do not know the difference between morning and night.
Oh, yes. They have a 26th of January in England. They also have a 27th, a 28th, and so on.
Who said the Delhi Daredevils and the Chennai Super Kings were playing against each other in those games?
You can't bury survivors under any law especially if they still have enough strength to object.
The bear that rang the doorbell would have to be a white bear. The only place you could build a house with
four southern exposures is at the North Pole where every direction is in South.
Ask
De‐brief question:
What were the barriers that came into your way of listening?
How can you overcome barriers to listening?
Say
There is a difference between hearing and listening.
If you don't listen properly, the message may be misunderstood.
Be open‐minded while listening to someone.
It is important to listen effectively and carefully without making assumptions.
Activity 3
Elevator Pitch:
You are in the lift of a hotel and you bumped into your former client who is a famous businessman. He has
financed a lot of small business ventures and can finance your new start‐up too. After exchanging pleasantries,
he asks you what your new company does. You open your mouth, and then pause. Where do you even begin?
Then, as you try to organize your thoughts, his meeting is called, and he is on his way. If you would been better
prepared, you're sure that he would have stayed long enough to schedule a meeting with you too.
If you were given another chance, what would you have said to this person?
Do
Start off the task by providing a beginning sentence to get the story started, and then go around the
classroom getting each one to add a new sentence to keep the story going.
This task should be done spontaneously allowing only a little time to think (30 seconds).
For example: There was once a student who was looking for a job after graduation.
312
86
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Summarize
Close the discussion by summarizing how to speak effectively as discussed in the Participant Handbook.
313
87
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Ask
What is a 'problem'?
What do you think are the problems you may face in the process of becoming a successful entrepreneur?
Say
Discuss the definition of problem as given in the Participant Handbook.
In a hurdle race the hurdles are the obstacles on the way to reach your goal.
Similarly, obstacles are the hurdles you may face while reaching your goal i.e. to set‐up your own business.
Your goal will be to reach the finishing line after crossing these hurdles.
Ask
What do you do when you face a problem?
How do you resolve it? You can pick examples from the question asked previously 'the problems they are
likely to face in the process of becoming a successful entrepreneur'.
Say
Discuss how to solve problems as given in the Participant Handbook.
Team Activity
This is a group activity.
The groups will solve the problem and come up with the best solution in each case.
1. Unable to arrange for some extra finance for setting up a beauty parlour. The loan sanctioned and disbursed is
not enough. You have tried all your contacts, friends and relatives. But unable to manage the extra amount.
Bank will not sanction more amount as you have used up the complete sanction limit.
2. You have rented a space for your business and all arrangements are done. You will be operating from the
office space rented in two days. Now the owner comes up to you and says he wants to sell the place and wants
you to vacate in 15 days.
3. You have just set up your business and need extra human resource. You have tried invieing a few also tied up
with an agency for getting the right candidate. But you are unable to get the right candidate. If the candidate is
good, you cannot offer the salary demanded. If the candidate agrees to the salary, he/she has other demands
like working hours to be reduced, leaves etc. which may not work for your set up.
314
88
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Do
Divide the class into three groups. Give one scenario to each group.
Explain the purpose and duration of the activity.
Ask the groups to build on the scenario and present their solution as a role play.
Say
De‐brief questions:
1. What was the problem?
2. Is there any other alternative solution?
3. Is this the best solution presented?
Ask
Try to think of some people around you who are able to solve problems very easily. Even you or your friends
might be approaching them when there is a problem. What qualities do they have? What personality traits do
such people possess?
Say
Discuss the important traits for problem‐ solving as given in the Participant Handbook.
Ask
In order to build a successful organization, you need to hire people who possess good problem solving skills.
How would you assess the level of problem solving skills of potential candidates before hiring them?
Say
Discuss how to assess for problem‐ solving skills as given in the Participant Handbook.
Summarize
Ask the participants the things that they have learnt so far.
Ask if they have any questions related to what they have talked about so far.
Summarize the discussion on problem solving.
Activity
The activity is to organise an election event. Select three volunteers from the group. They have to give a
speech on their election manifesto to the class. They have to negotiate with the fellow participants and
convince them to vote for them. The best negotiator will win the election.
Do
Ask three participants to volunteer for the activity.
Explain the purpose and duration of the activity.
Set guidelines pertaining to discipline and expected tasks.
315
89
Facilitator Guide
Facilitator Guide
Ask
Out of the three contestants, whom would you support? Why? What did they say or do which convinced you
to make your decision?
Have you ever tried to negotiate in your personal or professional life?
Ask the class to share some of their experiences where they have been able to strike a deal by negotiating.
Say
Discuss “What is Negotiation?” as given in the Participant Handbook.
Ask
Why is it important to negotiate? As an entrepreneur, where do you think that negotiation skills will be
needed?
Say
Discuss the importance of negotiation while starting a business as given in the Participant Handbook.
Say
Discuss the important steps to negotiate as given in the Participant Handbook.
Role Play
Conduct a role play activity.
Ask the participants to assemble together.
Explain the purpose and duration of the activity.
Set guidelines pertaining to discipline and expected tasks.
Do
Divide them into groups of four (4) (depending on the batch size).
Give them the hand‐outs for role play scenarios.
Two groups to be given scenarios on problem solving.
Other two groups to be given scenarios on negotiation.
The groups will build on the scenarios and prepare for the role play.
Give the groups atleast 5 mins to discuss and be ready with the role play.
Invite each group one by one to come and present their role play.
Problem solving Scenario 1
Avinash has a Mobile Repair Store in Allahabad. His outlet is one of the most popular one in the vicinity and
he has great rapport with his customers. He is always well‐dressed, jovial and full of energy.
It's around 11 AM, when a customer barges in to the shop and starts shouting at Avinash for giving her back
the instrument which is still not working. The screen of her mobile is also cracked from one side. Avinash
remembered thoroughly checking the handset before handing it over to the customer. The customer
threatens to sue the company and to go to Consumer Court for cheating her.
316
90
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Negotiation Scenario 1
You have interviewed a prospective new employee who could be a key member of your new entrepreneurial
venture. The new person is demanding a salary that is 20% higher than you thought based on your business
plan. Finances are tight, yet you believe this person could make a significant impact on future profits. If you
paid the required salary for the new person, then you would have to restructure your entire business plan.
You've been searching for an individual with this skill level for three months. to the candidate is waiting for
your response. Now you have to call him in to make the final negotiations.
Negotiation Scenario 2
You are a young entrepreneur who has just registered his start up project and applied for a bank loan
accordingly. You receive a letter saying that your loan application has been rejected as your start up idea did
not appeal to the bank and they think that it is not a revenue generating model. You have taken an
appointment to meet the manager and show your negotiation skills to get your loan approved.
Summarize
Wrap the unit up after summarizing the key points and answering questions.
317
91
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Blank sheets of paper
Pens
Ask
How does an entrepreneur identify an opportunity?
What do you think are the common queries or concerns faced by entrepreneurs?
How can you identify new business opportunity?
Say
Let's talk about opportunity, common queries or concerns faced by entrepreneurs, idea as an opportunity,
factors to consider when looking for opportunities, ways to identify new business, and opportunity analysis
as discussed in Participant Handbook.
Let's do an activity to understand ways to identify business opportunities within your business.
Do
Tell the class that this is an individual activity.
Tell the participants to create a matrix on their notebooks.
There will be four boxes in your matrix.
Strength, Weakness, Opportunity and Threats will be the four headings of the matrix. This is called the SWOT matrix.
Read out the questions to them and tell the participants they need to answer the questions asked in each matrix.
Tell them they can also use their own understanding of themselves to fill the SWOT matrix.
Activity
Do your SWOT analysis
Strength Weakness
What are your strengths? What are your weaknesses?
What unique capabilities do you possess? What do your competitors do better than you?
What do you do better than others?
What do others perceive as your strengths?
Opportunity Threat
What trends may positively impact you? Do you have solid financial support?
What opportunities are available to you? What trends may negatively impact you?
318
92
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Do
Congratulate everyone for the class activity.
Ask the audience to applaud for themselves.
Allot the participants sufficient time to complete this activity, but do keep a check on time.
Ask de‐brief questions to cull out information from the participants.
Ask
De‐brief questions:
What are your weaknesses according to your SWOT analysis?
Do you think you can change your weakness into strength? How?
Do you think you can work on your threats? How?
Summarize
Close the discussion by summarizing ways to identify business opportunities within your business.
Ask the participants what they have learned from this exercise.
Ask if they have any questions related to what they have talked about so far.
319
93
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Chart papers
Marker pens
Pencils
Colour pencils
Scale
Eraser
Other requisite stationery material
Ask
Do you think that entrepreneurs need support?
What do you think is an eco‐system?
What do you think 'entrepreneurship support eco‐system' means?
Say
Let's learn what entrepreneurship support eco‐system means.
Discuss 'Entrepreneurship Support Eco‐System' as given in the Participant Handbook.
Ask
Can you define entrepreneurship support eco‐system?
What are the key domains of the support eco‐system?
Say
Let's learn more about these domains by conducting an activity.
You have to make a poster showing the components of the six main domains of entrepreneurship support
eco‐system.
Team Activity
Making a poster showing the entrepreneurship support eco‐system.
320
94
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Do
Divide the class into groups of four or six.
Hand out chart paper and coloured pens.
Explain the purpose and duration of the activity.
Go around checking the progress of each group.
Set guidelines pertaining to discipline and expected tasks.
Activity De‐brief
Ask each group to display their poster and explain the key domains of entrepreneurship support eco‐system.
Policy
Market Finance
Entrepreneurship
Human
Capital Culture
Supports
Ask
What kind of government support eco‐system is available for entrepreneurs in India?
Say
Discuss 'Make in India' campaign as given in the Participant Handbook.
Team Activity
Presentation on key schemes to promote entrepreneurs
Do
Divide the class into pairs.
Number each pair from 1‐15.
Assign a scheme, same as their group number, to each group.
Ask them to read the scheme carefully and present it to the class.
Explain the purpose and duration of the activity.
Go around checking the progress of each group.
Set guidelines pertaining to discipline and expected tasks.
Activity De‐brief
Ask each group to explain the scheme offered by government to promote entrepreneurs.
Summarize
Summarize the unit by discussing the key points and answering questions the participants may have.
321
95
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Chart papers
Blank sheets of paper
Pens
Marker pens
Ask
Can you define risk or explain what constitutes a risk?
What do you people mean when they say, “This may be a risky proposition”?
What risks are they talking about?
Example Example
Suresh and his family too were travelling by car from Delhi to Nainital. It was their second trip there. His
friends too advised him to take a shortcut and turn left from Moradabad and take the Kaladhungi road as this
road was in a better condition.
Suresh too decided to take the Kaladhungi road but he left Delhi in the afternoon. It was dark by the time he
reached Kaladhungi, and he was sure that he was taking the correct turn. As it was late, he could not find
anyone to give him directions. He ended up being in an unknown place that was scarcely inhabited.
Say
Let's see what type of risks Rohit and Suresh took.
Discuss 'Risk Appetite and Resilience' with the participants as given in the Participant Handbook.
Say
Let's learn more about risk appetite and resilience with the help of an activity.
322
96
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Team Activity
Risk Appetite
This is a group activity.
In the previous unit, you read success stories of Mr Dhirubhai Ambani and Dr Karsanbhai Patel.
Mr Ambani left his job and started his company Reliance with just Rs. 50,000/‐.
Dr Patel kept his job, went door‐to‐door to sell Nirma, and only when the brand started gaining popularity
did he start his own company.
What types of risk did both of them take?
What risk factors, do you think, did they keep in mind before launching their company?
Write the Risk Appetite Statement of both the companies.
Activity De‐brief
Who took a greater risk?
What are the differences between the Risk Appetite Statement of both the companies?
Do
Instruct the participants that this is group work.
Divide the class into small groups of 4.
Give each group a chart paper.
Tell the participants that they have to evaluate the risks taken by Mr Dhirubhai Ambani and Dr Karsanbhai
Patel.
Give the participants 15 minutes to discuss and write.
Keep a check on time. Tell the group to wind up quickly if they go beyond the given time limit.
Ask
Do you think all entrepreneurial ventures are successful?
What happens if the first venture is not successful?
Should the entrepreneur stop when faced with challenges or face them?
Example Example
323
97
Facilitator Guide
Facilitator Guide
Say
Let's see what qualities made Vijay Shekhar Sharma a resilient entrepreneur.
Discuss Entrepreneurship and Resilience with the participants as given in the Participant Handbook.
Say
Let's learn more about entrepreneurship and resilience with the help of an activity.
Team Activity
Entrepreneurship and Resilience
This is a group activity.
Think of some entrepreneurship ventures that faced challenging times, but later resulted in success
stories.
Who is the founder of that company?
What challenging times did it face?
How did it overcome those challenges?
List the resilient characteristics of the entrepreneur.
Activity De‐brief
Each group to give their presentation.
Why did you choose this company?
What is the success story of the company?
Do
Instruct the participants that this is group work.
Divide the class into small groups of 4.
Give each group a chart paper.
Tell the participants that they have to think of an entrepreneur who faced challenging times, but eventually
succeeded.
Give the participants 15 minutes to discuss and write.
Keep a check on time. Tell the group to wind up quickly if they go beyond the given time limit.
Summarize
You can summarize the key points of the unit.
Ask the participants what they learned from the activities.
Clarify any questions or doubts they might have.
324
98
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Resources to be Used
Participant Handbook
Ask
Have you heard the quote 'nothing is impossible'?
What do you think it means?
Do you think that all successful entrepreneurs became famous overnight or did they have to struggle or face
failure before succeeding?
Example Example
Say
How do you define success and failure?
What is fear?
Discuss “success and failure” with the participants as given in the Participant Handbook.
Ask
Have you felt or experienced fear?
What led you to feel that emotion?
How did you handle it?
Say
Let's learn the about success and failure with the help of an activity.
325
99
Facilitator Guide
Facilitator Guide
Team Activity
Divide the class into groups of four.
Instruct them to think of one scenario where they have to interview a successful entrepreneur.
Explain the purpose and duration of the activity.
Set guidelines pertaining to discipline and expected tasks.
They have to choose one person from the group as the interviewee and one as the interviewer.
Go around and make sure they have understood what is to be done and are discussing the roles properly.
Check that everyone understands their role. Give clarifications if needed. Give the participants about
5 minutes to discuss and decide their roles.
Ask the groups to stop the discussion as soon as the time is over.
Invite each group one by one to come and present their interview as a role play.
Summarize
Wrap the unit up after summarizing the key points and answering questions.
326
100
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Notes
327
101
Facilitator Guide
Facilitator Guide
328
102
Welding and Quality
Employability & Entrepreneurship Skills
Technician
329
103
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Chart papers
Markers pens
Blank sheets of paper
Ask
Suppose, you want to open a restaurant, what are the factors you will consider?
How will you promote your restaurant?
Example Example
Say
Discuss “Market Study” with the participants. Refer to the Participant Handbook.
Let's learn about market study and research with the help of an activity.
Team Activity
Market Study
This is a group activity.
You want to start your own tuition centre.
What type of research will you do?
Activity De‐brief
Ask each group to come forward and give a brief presentation.
Encourage other groups to be interactive and ask questions.
What factors did you keep in mind while doing your research?
Based on our research would you go ahead and open a tuition centre?
330
104
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Do
Instruct the participants that this is group work.
Divide the class into small groups of 4 or 6.
Give each group a chart paper.
Tell the participants that they have to start their own tuition centre.
Give the participants 10 minutes to discuss and write the research work they need to do.
Keep a check on time. Tell the group to wind up quickly if they go beyond the given time limit.
Say
By opening a tuition centre you are offering a service.
Ask
What factors will you keep in mind before opening it?
Say
Discuss “The 4Ps of Marketing” with the participants as given in the Participant Handbook.
Say
Let's learn about the 4Ps of Marketing with the help of an activity.
Team Activity
4 Ps of Marketing
This is a group activity.
You have to sell a pen to four different segments:
1. Rural villagers
2. Rural middle class
3. Urban middle class
4. Upper end rich people (Niche market)
Keeping the 4Ps of Marketing in mind, what marketing strategy will you design to sell the pen?
Activity De‐brief
Ask each group to to present their strategy.
Encourage other groups to be interactive and ask questions.
Do
Instruct the participants that this is group work.
Divide the class into four groups.
Give each group a chart paper.
Assign each group a target audience for selling the pens:
1. Rural villagers
2. Rural middle class
3. Urban middle class
331
105
Facilitator Guide
Facilitator Guide
Say
Each entrepreneur has an idea of wants he wants to sell. It may be a service or a product.
Discuss “Importance of an IDEA” as given in the Participant Handbook.
Summarize
Summarize the key points of the unit.
Ask the participants what they learnt from the activities.
Encourage them to ask if they have any doubts.
332
106
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Resources to be Used
Participant Handbook
Say
Let's recall some basic business terminology.
Discuss the Business Entity Concepts as given in the Participant Handbook.
Let's learn some basic business terminology by having an activity.
We will have a quiz today.
Activity
The activity is a quiz.
Do
Divide the class in two groups and give a name to each group.
Explain the rules of the quiz. For each correct answer the group gets 1 mark.
If the group is unable to answer the question is passed to the next group.
Explain the purpose and duration of the activity.
Ask the questions of the quiz.
Keep a score of the groups.
Set guidelines pertaining to discipline and expected tasks.
Summarize
Summarize the unit by discussing the key points.
333
107
Facilitator Guide
Facilitator Guide
334
108
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Resources to be Used
Participant Handbook
Ask
Can your business run without customers/buyers?
Who is the most important entity in any business?
Say
The key to every success business lies on understanding the customer's expectations and providing excellent
customer service.
Discuss about CRM and its benefits. Refer to the Participant Handbook.
Providing excellent customer service entails:
Treating your customers with respect.
Be available as per their need/ schedule.
Handling complaints effectively.
Building long lasting relationships.
Collecting regular feedback.
Handle customer complaints proactively. Ask “what happened”, “why it happened”, “how can it be avoided
next time”, etc.
Collecting feedback from the customers regularly will enable you to improve your good/service.
“Let's understand it better with the help of some case scenarios. You will be given some cases within your
groups. You have to analyse the case scenario that has been given to you and then find an appropriate
solution to the problem.”
Do
Divide the class into four groups of maximum six participants depending on the batch size.
Give one case study to each group.
Instruct them to read the case carefully.
The group is expected to analyse and discuss the case amongst them and find a solution to the given problem.
Put down the discussion points (de‐brief questions) on the board. Give the class 5‐10 minutes to discuss the
case and note down their solutions.
At the end of 10 minutes, the team should present their case solution to the class.
335
109
Facilitator Guide
Facilitator Guide
Team Activity
Case Study Analysis
Raju runs a business of wooden furniture. He has a huge list of customers on Facebook and WhatsApp who give
him orders regularly. Ankita is one of his old and regular customers. She placed an order for a new chester and TV
cabinet via WhatsApp and requested Raju to send them as soon as possible. When the parcel reached Ankita
through courier she found that chester was broken and the TV unit was chipped from the bottom. Ankita was
heartbroken. It was a complete waste of money. She sent a message to Raju on WhatsApp, expressing her anger
and disappointment. Raju might lose an old customer forever if he doesn't satisfy the customer. What should
Raju do to retain his customer?
Scenario 2
Rajni runs a boutique shop. She sells suits and sarees. She is one of the most successful designer in her city. Rajni
swears that all the clothes in her boutique have unique designs. Smita has to attend her cousin's wedding; she
goes to Rajni's boutique to buy a saree. Smita wanted a unique designer saree. Rajni customized a saree for her
and sent it over the courier. When Smita had a look at the saree she realised her two friends had the same design
sarees. She sent a message to Rajni on WhatsApp, expressing her anger and disappointment. Did Rajni make a
false promise? Were her designs copied? What could happen to Rajni's image after this incident? What would
you do if you were in Rajni's place?
Scenario 3
Shama is a beautician who offers parlour services to ladies by making home visits. Recently, Shama got her name
registered on an e‐ commerce website. Two days earlier, she got a message from Mrs Sushma. The appointment
was fixed for next day, 11:00 am and the remuneration for the services was decided beforehand. When Shama
reached there at 10:50 am, Mrs Sushma was not at home. When Shama called her, she asked her to wait for a
while. Mrs Sushma reached home at 11:45 am. Meanwhile, Shama had to reschedule her next appointment.
After availing Shama’s services, Mrs Sushma refused to pay the requisite amount and started finding faults in the
services provided by her. Who was at fault in this scenario? What should you do in case the customer behaves
unreasonably? What would you do if you were in Shama’s place?
Scenario 4
Shailender is the manager of a car showroom. He proactively takes part in all the transactions that happen in his
showroom. Vinita wants to buy a new car. She has chosen a car from Shailender’s showroom. The salesperson
has given her a very good discount and has also promised free service for one year. Vinita goes to the showroom
and asks to complete all the formalities to purchase the car. When she sees the final bill she realize that she has
not received the promised discount neither was there any mention of the free services. She immediately
demands to see the Shailender. When Shailender’s head asks how much discount Vinita was promised, he
realised the discount will make the sale in loss. The car showroom owner might lose a customer and deal due to
false commitments made by his manager. Besides, the customer might tell this to other people, creating a bad
name and image for the showroom. If you owned that showroom, how would you have convinced your
customer?
Say
Now, let's discuss the problem and solution with the class.
The group will first briefly describe the case to the class.
Then discuss the issue identified and the proposed solution.
Present the solution as a role play.
Post presentation, the other groups may ask questions from the group that has presented.
336
110
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Do
Congratulate each group for the presentation/ role play.
Ask the audience to applaud for them.
Keep a check on time. Tell the group to wind up the discussion quickly if they go beyond the given time limit.
Say
If your customers are happy with you they will give referrals which will help to grow your business.
One more way of growing business is 'Networking'.
Discuss Networking and its benefits. Refer to the Participant Handbook.
Activity
Group Discussion
Conduct a group discussion in the class on how they can do networking for their business.
Summarize
Ask the participants what they have learnt from this exercise/ activity.
Ask if they have any questions related to what they have talked about so far.
Close the discussion by summarizing the importance of CRM and Networking for entrepreneurs.
Close the discussion by summarizing the importance of CRM and Networking for entrepreneurs.
337
111
Facilitator Guide
Facilitator Guide
Resources to be Used
Participant Handbook
Chart papers
Blank papers
Marker pens
Ruler
Ask
Remember we had written SMART Goals in a previous session? Let's try and recall why it is important to set
goals?
While framing SMART goals, we talked about 'T' in SMART, which was 'Time Bound'? What do we mean by
time bound goals?
What time limit did you set for your goal‐ 3 weeks, 3 years, 10 years?
Say
Talk about short term, long term and medium term goals, as discussed in the Participant Handbook.
Ask
As you are planning to become an entrepreneur, you must have thought of an idea for a start‐up. What is your
business idea?
Do
Ask few participants to share their business ideas.
Ask
Have you created a business plan for your business idea?
Do you think it is important to have a business plan in place? Why/ why not?
Say
Talk about 'Why Create a Business Plan' as discussed in the Participant Handbook.
Let's understand it better with the help of an activity.
338
112
Welding and Quality
Employability & Entrepreneurship Skills
Technician
Team Activity
Writing a business Plan
This is a group activity.
Give the groups the required resources such as chart paper and markers.
This activity is divided into two parts:
1. Create a business idea
2. Develop a business plan
The group will discuss and come up with a new business idea and present their idea to the class.
In the second part of the activity the group will develop a business plan for the business idea.
The business plan prepared will be presented by the groups to the class.
MY BUSINESS PLAN
Executive Summary: What is your Mission Statement?
Marketing and Sales: How will you advertise and sell your products?
Say
Teams will need to brainstorm for this part of the activity.
Use the blank papers for the second part of this activity
Make your business plan on a chart paper based on the following parameters:
1. Executive Summary
2. Business Description
3. Market Analysis
4. Organization and Management
5. Service or Product Line
6. Marketing and Sales
Explain each parameter in detail as done in the Participant Handbook.
Discuss each parameter with the business idea examples of the groups.
Groups will discuss and develop the business plan for their business idea.
339
113
Facilitator Guide
Facilitator Guide
Say
Now, let's share our plan with the class.
Each group will briefly describe the plan to the class.
Post presentation, the other groups may ask questions to the group who have presented their plan.
Do
Congratulate each group for sharing their points.
Ask the audience to applaud for them.
Keep a check on time. Tell group to wind up the discussion quickly if they go beyond the given time limit.
Say
Along with a business plan, you need to create a financial plan and evaluate the risk involved with your start
up.
Discuss 'Financial Planning' and 'Risk Management' in detail as given in the Participant Handbook.
Summarize
Ask the participants what they have learnt from this exercise/ activity.
Ask if they have any questions related to what they have talked about so far.
340
114
Welding and Quality
Employability & Entrepreneurship Skills
Technician
UNIT 13.6.5:
0 Procedures and Formalities for Bank Finance
Unit Objectives
At the end of this unit, participants will be able to:
Describe the procedure and formalities for applying for bank finance
Resources to be Used
Participant Handbook
Bank loan/finance form sample
Ask
While preparing a business plan in the last session, we discussed financial planning to arrange financial
resources for your start‐up. Therefore, how will you collect funds to start your business?
Say
While most entrepreneurs think 'product' is the most difficult thing to decide for a business, start‐up capital
poses an even a bigger obstacle. Though there are various ways of funding the business, to convince investors
to invest money is the most challenging.
Some of the funding options available in India are:
Bootstrapping: Also called self‐financing is the easiest way of financing
Crowd funding: Funds are collected by consumers pre‐ordering or donating for starting the business.
Angel investors: Individual or group of investors investing in the company
Venture capitalists: Venture capitals are professionally managed funds who invest in companies that have
huge potential. They usually invest in a business against equity.
Bank loans: The most popular method in India.
Microfinance Providers or NBFCs
Government programmes
Let us know discuss the most popular method i.e. bank finance in detail here.
Do
Discuss the list of documents that are required to apply for a loan like letter of introduction, business
brochure, references of other banks, and financial statements.
Explain the details to be filled in a loan application form.
Divide the class into groups. Give each group a loan application form.
Ask the groups to discuss and fill the form.
Summarize
Close the discussion by summarizing the important documents needed for bank loan.
Ask the participants if they have any questions related to what they have talked about so far.
341
115
Facilitator Guide
Facilitator Guide
1. Audited financial statements of the business concern for the last three years
3. Audited financial statements of associate concern/s for the last three years
6. CMA data for the last three years, estimates for current year and projection for the next year
11. Copies of ITAO of the company for the last three years
12. Copies of certificate from banks and financial institutions certifying the latest liability with them
14. Copy of board resolution authorizing the company to apply to your bank for the credit facilities
mentioned in application
15. Copy of memorandum and article of association (in case of limited company)/partnership deed
(in case of partnership firm)
16. Cash budget for the current year and next year in case of contractors and seasonal industries
342
116
Welding and Quality
Employability & Entrepreneurship Skills
Technician
UNIT 13.6.6:
0 Enterprise Management – An Overview: How to
Manage Your Enterprise?
Unit Objectives
At the end of this unit, participants will be able to:
Discuss how to manage their own enterprise
Resources to be Used
Participant Handbook
Ask
Having set‐up a business, do you think it is possible to do everything on your own?
Does one require trained persons for help?
What does management mean?
Say
Let's have a look at this example:
Kapil had a small business that was beginning to pick up pace. He wanted to expand his business, and
therefore employed few more people. One day, as he was walking past Ramesh, one of his new employees, he
overheard Ramesh talking rudely to a customer on the phone. This set him thinking. Kapil realised that he
should have regular team meetings to motivate his employees and speak with them about any problems they
might be facing during work. He should also conduct training sessions on new practices, soft skills, and
technology, and develop work ethics manual for managing his enterprise.
Say
Was Kapil correct in his approach or he should have scolded Ramesh instantly in front of his other employees?
Discuss “Enterprise Management – An Overview” with the participants as given in the Participant Handbook.
Say
Let's learn how to effectively manage an enterprise or business through an activity.
Team Activity
Enterprise Management
This is a group activity.
Design a matrix listing the topics and key words that are needed to run an enterprise effectively and smoothly.
Activity De‐brief
Have each group present their matrix.
Encourage participants of the other groups to ask question about each other's presentation.
343
117
Facilitator Guide
Facilitator Guide
Do
Instruct the participants that this is group work.
Divide the class into small groups of 4.
Give each group a chart paper and coloured pen.
Tell the participants that they have make a matrix they need to fill.
They have to write the main topics and key words that will them effectively manage their enterprise.
Give the participants 15 minutes to discuss and write.
Keep a check on time. Tell the group to wind up quickly if they go beyond the given time limit.
Summarize
Ask the participants what they have learned from this exercise/activity.
Ask if they have any questions related to what they have talked about so far.
Close the discussion by summarizing the importance of effective management to run an enterprise as
given in the Participant Handbook.
344
118
Welding and Quality
Employability & Entrepreneurship Skills
Technician
UNIT 13.6.7:
0 20 Questions to Ask Yourself before Considering
Entrepreneurship
Unit Objectives
At the end of this unit, participants will be able to:
List the important questions that every entrepreneur should ask before starting an enterprise
Resources to be Used
Participant Handbook
Blank sheets of paper
Pens
Ask
Why do you want to become an entrepreneur?
Say
It is very important to know why you want to become an entrepreneur. Your personal goals for becoming an
entrepreneur play a key role in the success of your business. Your goals should be clear well before you start
your business.
Apart from the goals, the other aspects of business that you need to bear in mind are the potential problems
that you may face to set‐up, your areas of interest, and all the other dimensions of the business.
Let's understand it better with the help of some questions that every entrepreneur should ask before starting
their own business.
Open the Participant Handbook section named '20 Questions to Ask Yourself Before Considering
Entrepreneurship'. You have to answer the questions individually.
Then, we will have a class discussion on all the questions.
Do
Read out the questions one by one in front of all the participants.
Participants have to answer all the one by one questions.
Give the class 10‐15 minutes to note down their answers.
At the end of 15 minutes, open the discussion for all the questions.
Moderate the discussion by focusing on the relevant points.
Keep a check on time and don't let the discussion get sabotaged or lose track of time. Ensure all the questions
are covered and discussed.
Summarize
Ask the participants what they have learned from this exercise/activity.
Ask if they have any questions related to what they have talked about so far.
345
119
Facilitator Guide
Facilitator Guide
Notes
Notes
346
120
11. Annexures
Annexure I: Training Delivery Plan
Annexure II: Assessment Criteria
Facilitator Guide
Annexure I
Training Delivery Plan
Training Delivery Plan
Program Name: Certificate Course in Welding and Quality Technician
Qualification Pack Welding and Quality Technician - ACS/Q3109
Name & Ref. ID
Version No. 1.0 Version Update Date 05-04-2019
Pre-requisites to Class 10th Standard Pass
Training (if any)
Training Outcomes By the end of this program, the participants will be able to:
1. Identify the component requirements and the equipment to be used.
2. Perform operation of welding machine as per the work instructions/ guidance
from the supervisor.
3. Support the operator/supervisor in various kinds of welding operations.
4. Perform minor machine maintenance activities.
5. Perform complete dimensional, layout inspection and visual check as per product
drawing.
6. Perform unloading of finished goods from the production line and store them
properly in the designated area.
7. Record the observations in the inspection check sheet.
8. Use inspection equipment and instruments such as Vernier Micrometer, height
gauge and air gauges and similar other items.
9. Carry out dock audit consisting of visual, labelling and packaging checks.
10. Conduct regular cleaning and maintenance of equipment.
11. Maintain a safe and healthy work place by adhering to the safety guidelines in
the working area of the organization and following the practices which are not
impacting the environment in a negative manner.
12. Maintain 5S in the work premises by sorting, streamlining & organizing, storage
and documentation, cleaning, standardization and sustenance across the plant
and office premises of the organization.
Sl. Module Session Session Objectives NOS Methodology Training Tools/Aids Duration
No Name Name Reference
1 Introduction Icebreaker • General Discipline Group • Class Room Size 8 hour
in the class room Activity: • Chairs/Tables
• General Safety Passing the
• Computer with
Rules Parcel
Internet
348
Welding and Quality
Technician
349
Facilitator Guide
350
Welding and Quality
Technician
• Height Gauge
• Straight Edge &
Squares
• Abrasive Cutter
for Samples
• Polishing
machine
• HNo3 Acid for
Penetration
check
• Hardness
Tester
• Sample parts
from small
to big for
practicing
welding
in various
thickness
• Goggles
• Protective
Gloves
• Shields
• Ear Plugs
• Aprons
• Safety Shoes
• Fire Fighting
Equipment
• First Aid Box
• Maintenance
Manuals
and Welding
handbooks
• Necessary
spares of
machines
voltage &
current meters
• Standards
for welding
symbols
• Standards of
GD & T BIS,
ASME & ASTM
• Welding
Simulators
351
Facilitator Guide
3 Prepare the Welding • Understand the ASC/ • Facilitator- • Different types 8 hrs
welding positions, right welding N3104 led- of joints
machine welding methodology and discussion • Bench Drill
PC1, PC2,
for the process, process to be ad- PC3, PC4, • Skill • Drills & Taps
welding welding opted for complet- Practice
PC5, PC6, • Bench Grinder
process parameter, ing the work order (Activity)
PC7, PC8, • AC/DC Arc
material and from the supervi-
sor. PC9, PC10, welder
accessories PC11, • Electrode
require PC12,
• Understand the Holder 8 hrs
right welding PC13
• Electrodes
methodology and KB1, KB2, (M.S)
process to be ad- KB3, KB4, • Welding booth
opted for complet- KB5, KB6, with Exhaust
ing the work order KB7 (3’ x 2.5’ x 3.5’)
from the supervi-
SA1, SA2, • Metal Inert Gas
sor.
• Understand the SA3, SA4, welding (MIG)
SA5, SA6, Set (Single
various welding
SA7, SA8 phase)
parameter like
electrode type, SB1, SB2, • Wire feeder
electrode distance SB3, SB4, and Roll
(gaps) welding cur- SB5, SB6, • CO2 gas
rent, voltage, pro- SB7, SB8, cylinder +
cess time before SB9, SB10, Regulator + gas
starting welding SB11, heater & flow
process meter
SB12, SB13
• Torch with
• Understand the Nozzle 8 hrs
various welding • Tungsten Inert
parameter like gas Welding
electrode type, (TIG) set with
electrode distance Electrode
(gaps) welding cur-
• Argon gas
rent, voltage, pro-
cylinder
cess time before
starting welding • Hammer/
process Chipping
• Understand the • Wire Brush
material required • Spot/Projection
and the equip- Welding
ment availability machine with
for executing the tips
activity. • Equipment
352
Welding and Quality
Technician
353
Facilitator Guide
• Hardness
Tester
• Sample parts
from small
to big for
practicing
welding
in various
thickness
• Goggles
• Protective
Gloves
• Shields
• Ear Plugs
• Aprons
• Safety Shoes
• Fire Fighting
Equipment
• First Aid Box
• Maintenance
Manuals
and Welding
handbooks
• Necessary
spares of
machines
voltage &
current
meters
• Standards
for welding
symbols
• Standards of
GD & T BIS,
ASME & ASTM
• Welding
Simulators
4 Support the Installation • Install the work ASC/ • Facilitator- • Different types 8 hrs
welder in of welding pieces on the N3105 led- of joints
the welding machine, welding appa- discussion • Bench Drill
PC1, PC2,
process parameter ratus keeping in PC3, PC4, • Skill Practice • Drills & Taps
setting, mind the elec- (Activity)
PC5, PC6, • Bench Grinder
welding trode distance,
PC7, PC8, • AC/DC Arc
operation, contact area,
pressure, temper- PC9, PC10 welder
measuring
ature, application KB1, KB2,
material
as per welding KB3, KB4,
SOP/control plan KB5, KB6
354
Welding and Quality
Technician
355
Facilitator Guide
356
Welding and Quality
Technician
5 Remove Post welding • Understand the ASC/ • Facilitator- • Different types 8 hrs
the finished operations, output product N3106 led- of joints
goods and clamping shape and de- discussion • Bench Drill
PC1, PC2,
store them material, cide the suitable PC3, PC4, • Skill • Drills & Taps
in the checking output mechanism to Practice
PC5, PC6, • Bench Grinder
designated and quality lift the output (Activity
PC7 • AC/DC Arc
place 8 hrs
• Understand the KB1, KB2 welder
output product SA1, SA2, • Electrode
shape and de- SA3, SA4, Holder
cide the suitable SA5, SA6,
mechanism to
SA7
lift the output
357
Facilitator Guide
358
Welding and Quality
Technician
• Hydraulic &
lubricating oil
• Consumables
like
electrodes
gas cylinder &
similar item
• Fixtures
for holding
components
• Defective &
good samples
of weld
• Control plan,
operation
std & work
Instructions
• Vernier
• Micrometer
• Surface plate
• V Block
(magnetic)
• Height Gauge
• Straight Edge
& Squares
• Abrasive
Cutter for
Samples
• Polishing
machine
• HNo3 Acid for
Penetration
check
• Hardness
Tester
• Sample parts
from small
to big for
practicing
welding
in various
thickness
359
Facilitator Guide
• Goggles
• Protective
Gloves
• Shields
• Ear Plugs
• Aprons
• Safety Shoes
• Fire Fighting
Equipment
• First Aid Box
• Maintenance
Manuals
and Welding
handbooks
• Necessary
spares of
machines
voltage &
current
meters
• Standards
for welding
symbols
• Standards of
GD & T BIS,
ASME & ASTM
• Welding
Simulators
6 Conduct Doing quality • Measure the ASC/ • Facilitator- • Different types 8 hrs
quality checks, using specifications of N0007 led- of joints
checks and measuring the finished prod- discussion • Bench Drill
PC1, PC2,
inspection of instruments, uct using devices PC3, PC4, • Skill • Drills & Taps
the finished removing like micrometers, Practice
PC5, PC6 • Bench Grinder
metal cast damage vernier calipers, (Activity
gauges, rulers, KB1, KB2, • AC/DC Arc
products material and
weighing scales and KB3 welder
repairing
any other inspec- SA1, SA2, • Electrode
work
tion equipment and SA3, SA4, Holder
compare with the SA5, SA6 • Electrodes
parameters given in (M.S)
SB1, SB2,
the work order
SB3, SB4, • Welding booth
• Compare texture, with Exhaust
color, surface prop- SB5,
SB6, SB7, (3’ x 2.5’ x
erties, hardness 3.5’)
and strength with SB8, SB9,
the given product SB10, • Metal Inert
SB11 Gas welding
specifications
(MIG) Set
360
Welding and Quality
Technician
361
Facilitator Guide
• Defective &
good samples
of weld
• Control plan,
operation
std & work
Instructions
• Vernier
• Micrometer
• Surface plate
• V Block
(magnetic)
• Height Gauge
• Straight Edge
& Squares
• Abrasive
Cutter for
Samples
• Polishing
machine
• HNo3 Acid for
Penetration
check
• Hardness
Tester
• Sample parts
from small
to big for
practicing
welding
in various
thickness
• Goggles
• Protective
Gloves
• Shields
• Ear Plugs
• Aprons
• Safety Shoes
• Fire Fighting
Equipment
362
Welding and Quality
Technician
363
Facilitator Guide
364
Welding and Quality
Technician
• Coordination with
the respective
process owners/
seniors in QA and
implement CAPA for
discrepancies in the
parameters identi-
fied in the report on
immediate basis.
365
Facilitator Guide
8. Conduct Housekeeping • Arrange all equip- ASC/ • Facilitator- • Different types 8 hrs
regular of workshop, ment in a proper N0008 led- of joints
cleaning and maintenance order as indicat- discussion • Bench Drill
PC1, PC2,
maintenance of tools and ed in the equip- PC3, PC4, • Skill • Drills & Taps
of the equipment, ment manual Practice
PC5, PC6, • Bench Grinder
equipment checking and • Store equipment (Activity)
PC7, PC8, • AC/DC Arc
inspection auxiliaries and
spare parts in PC9, PC10, welder
of tools and PC11
proper designat- • Electrode
machines
ed areas KB1, KB2, Holder
KB3, KB4 • Electrodes
• tag process re- 8 hrs
SA1, SA2, (M.S)
lated equipment SA3, SA4, • Welding booth
parts/ spare SA5, SA6, with Exhaust
parts as per part (3’ x 2.5’ x 3.5’)
SA7
number or serial
number so that SB1, SB2, • Metal Inert Gas
sorting of equip- SB3, SB4, welding (MIG)
SB5, SB6, Set (Single
ment becomes
SB7, SB8, phase)
easy
• Check the work- SB9, SB10, • Wire feeder
ing of all bearing, SB11 and Roll
rollers, shafts etc. • CO2 gas
and oil all mov- cylinder +
ing parts of the Regulator + gas
equipment on a heater & flow
periodic basis meter
• Torch with
• Check the work- Nozzle 8 hrs
ing of non- • Tungsten Inert
moving parts and gas Welding
periodically con- (TIG) set with
duct preventive Electrode
maintenance to
• Argon gas
prevent machine
cylinder
failure
• Periodically check • Hammer/
the equipment Chipping
calibration and • Wire Brush
report any errors • Spot/Projection
to the mainte- Welding
nance teams for machine with
rectification tips
366
Welding and Quality
Technician
367
Facilitator Guide
• Hardness
Tester
• Sample parts
from small
to big for
practicing
welding
in various
thickness
• Goggles
• Protective
Gloves
• Shields
• Ear Plugs
• Aprons
• Safety Shoes
• Fire Fighting
Equipment
• First Aid Box
• Maintenance
Manuals
and Welding
handbooks
• Necessary
spares of
machines
voltage &
current
meters
• Standards
for welding
symbols
• Standards
of GD & T
BIS, ASME &
ASTM
• Welding
Simulators
368
Welding and Quality
Technician
369
Facilitator Guide
10 Maintain 5S 5S safety • Follow the sorting ASC/N0021 • Facilitator- • Tools, fixtures 8 hrs
at the work system, waste process and check PC1, PC2, led- & jigs
premises management, that the tools, discussion
PC3, PC4, • Personal
waste fixtures & jigs PC5, PC6, • Skill Practice Protection
management that are lying on (Activity
PC7, PC8, Equipment:
methods, workstations are
PC9, PC10, Gloves,
storing and the ones in use and
un-necessary items PC11, Safety Shoes,
stacking of PC12, goggles, ear
are not cluttering
material PC13, plugs
the work benches
or work surfaces. PC14, • SOP
PC15, document
• Ensure segregation PC16, and charts on 8 hrs
of waste in hazard- PC17, segregation
ous/ non Hazard- PC18, and disposal
ous waste as per PC19, of waste
the sorting work PC20,
instructions • SOP on health
PC21,
safety and
PC22,
• Segregate the environment 8 hrs
PC23,
items which are PC24, • Safety sign
labelled as red tag boards/signs
PC25, PC26
items for the pro- • Risk
cess area and keep KB1, KB2, mitigation
them in the correct KB3, KB4,
KB5, KB6, plan
places
KB7, KB8, • SOP on safety
• Properly stack the KB9, KB10, and fire drills 8 hrs
various types of KB11, • Bins,
boxes and contain- KB12, containers,
ers as per the size/ KB13, KB14 drums, trays,
utility to avoid cabinets,
SA1, SA2,
any fall of items/ lockers, boxes
SA3, SA4,
breakage and also etc
SA5,
enable easy sorting
when required SB1, SB2, • Cleaning
SB3, SB4, material and
• Make sure that all SB5, SB6, equipment 8 hrs
material and tools SB7, SB8,
are stored in the SB9, SB10
designated places
and in the manner
indicated in the 5S
instructions
370
Welding and Quality
Technician
• Participate active- 1 hr
ly in employee
work groups on
5S and encourage
team members
for active partici-
pation
371
Facilitator Guide
Annexure II
Assessment Criteria
CRITERIA FOR ASSESSMENT OF TRAINEES
Assessment Criteria
Job Role Welding and Quality Technician
Qualification Pack ASC/Q3109, Version 1.0
Sector Skill Council Automotive
1 Criteria for assessment for each Qualification Pack will be created by the Sector Skill Council. Each
Performance Criteria (PC) will be assigned marks proportional to its importance in NOS. SSC will also
lay down proportion of marks for Theory and Skills Practical for each PC.
2 The assessment for the theory part will be based on knowledge bank of questions created by the SSC.
3 Individual assessment agencies will create unique question papers for theory part for each candidate
at each examination/training centre (as per assessment criteria below).
4 Individual assessment agencies will create unique evaluations for skill practical for every student at
each examination/training canter based on this criteria.
5 To pass the Qualification Pack, every trainee should score a minimum of 70% in each NOS.
6 The marks are allocated PC wise; however, every NOS will carry a weight age in the total marks allocated
to the specific QP.
Marks Allocation
Assessment Assessment criteria (PC) Total Marks Out Of Theory Skills
outcome Practical
(NOS Code and
Description)
372
Welding and Quality
Technician
373
Facilitator Guide
374
Welding and Quality
Technician
375
Facilitator Guide
376
Welding and Quality
Technician
377
Facilitator Guide
378
Welding and Quality
Technician
379
Facilitator Guide
380
Welding and Quality
Technician
381
Facilitator Guide
382
Welding and Quality
Technician
Do
• Explain each Guideline for Assessment in detail
• Explain the score that each trainee needs to obtain
• Recapitulate each NOS one-by-one and take participants through the allocation of marks for Theory
and Skills Practical.
• Explain the Allocation of Marks. Explain that they will be assessed on Theory and Skills Practical.
• Explain that for the first NOS, 25 marks are allotted for Theory and & 75 for Skills Practical.
Notes
383
Address: Sat Paul Mittal Building, 1/6, Siri Institutional Area, Khel Gaon Road,
New Delhi, Delhi 110049
Email: [email protected]
Address: 204, Aashirwad Complex, D-1, Green Park, New Delhi – 110016
E-mail: www.asdc.org.in
Web: [email protected]
Web: www.csdcindia.org
Phone:
Phone: 011 4186 8090
+91-11-46584466
CIN No.: 00000000000000000
978-1-111-22222-45-7
Price: