Professional Documents
Culture Documents
Simplexa™ COVID-19 Direct: Fluorescent Probes Are Used Together With Corresponding Forward and Reverse Primers
Simplexa™ COVID-19 Direct: Fluorescent Probes Are Used Together With Corresponding Forward and Reverse Primers
REF MOL4150
Rev. 05
(English)
INTENDED USE
®
The DiaSorin Molecular Simplexa™ COVID-19 Direct real-time RT-PCR assay is intended for use on the LIAISON MDX instrument
for the in vitro qualitative detection of nucleic acid from severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) in
nasopharyngeal swabs (NPS), nasal swabs (NS), nasal wash/aspirate (NW) or bronchoalveolar lavage (BAL) specimens from
individuals suspected of COVID-19 by their healthcare provider. The Simplexa™ COVID-19 Direct assay is an aid in the diagnosis
of SARS-CoV-2 infection.
Testing is limited to laboratories certified under the Clinical Laboratory Improvement Amendments of 1988 (CLIA), 42 U.S.C. §263a,
to perform high or moderate complexity tests.
Results are for the identification of SARS-CoV-2 RNA. The SARS-CoV-2 RNA is generally detectable in upper respiratory and
bronchoalveolar lavage (BAL) specimens during the acute phase of infection. Positive results are indicative of the presence of
SARS-CoV-2 RNA; clinical correlation with patient history and other diagnostic information is necessary to determine patient
infection status. Positive results do not rule out bacterial infection or co-infection with other viruses. The agent detected may not be
the definite cause of disease. Laboratories within the United States and its territories are required to report all positive results to the
appropriate public health authorities.
Negative results do not preclude SARS-CoV-2 infection and should not be used as the sole basis for patient management decisions.
Negative results must be combined with clinical observations, patient history, and epidemiological information.
The Simplexa™ COVID-19 Direct assay is intended for use by qualified and trained clinical laboratory personnel specifically
instructed and trained in the techniques of real-time PCR and in vitro diagnostic procedures. Simplexa™ COVID-19 Direct is only for
use under the Food and Drug Administration’s Emergency Use Authorization.
MATERIALS PROVIDED
The Simplexa™ COVID-19 Direct assay contains sufficient reagents for 24 reactions. Upon receipt, store at -10 to -30 ºC (do not
use a frost-free freezer). Each vial contains sufficient material for one use. Use within thirty (30) minutes of thawing.
Simplexa™ COVID-19 Direct — Page 2
KIT DESCRIPTION
EC SYMBOL Abbreviated Cap Number Reactions Volume
Component Name REF
ON LABEL Name Color of Vials per Vial/Kit per Vial
Simplexa™ COVID-19 Direct Reaction Mix MOL4151 REAG C Co19 Brown 24 1/24 50 µL
COMPONENT DESCRIPTION
Internal Control
RNA (IC)
Q670 644 670 N/A
RECOMMENDED MATERIALS
1. Universal Transport Media (UTM, Copan) or Universal Viral Transport (UVT, BD) to be used as a No Template Control (NTC).
QUALITY CONTROL
Simplexa™ COVID-19 Positive Control Pack (MOL4160) may be used as an external control for Quality Control (QC) testing,
training or proficiency testing. Each laboratory should establish its own QC ranges and frequency of QC testing based on
applicable local laws, regulations and standard good laboratory practice. Refer to the Simplexa™ COVID-19 Positive Control Pack
(IFUC.US.MOL4160) for instructions on running the positive control.
INTERPRETATION OF RESULTS
Upon completion of the run, the software automatically calculates and displays results.
1. For each accession ID (Sample ID) entered, the software displays a result (“Positive”, “Negative”, “Invalid”, “EC500, EC505 or
EC515”) for SARS-CoV-2 RNA.
Results
SARS-Cov-2 Target Interpretation
ORF1ab S gene
Positive Positive Result indicates the presence of SARS-CoV-2 RNA in the patient sample.
Positive ---- Result indicates the presence of SARS-CoV-2 RNA in the patient sample.*
---- Positive Result indicates the presence of SARS-CoV-2 RNA in the patient sample.*
Negative Negative Result indicates the absence of SARS-CoV-2 RNA in the patient sample.
Result indicates inability to conclusively determine presence or absence of SARS-CoV-
Invalid 2 RNA in the patient sample. This result may be due to 1) Internal Control (IC) failure,
or 2) failure to detect sufficient specimen volume. The sample needs to be retested.
See “Invalid Results” section below.
Simplexa™ COVID-19 Direct — Page 5
Results Interpretation
EC500 Data processing error due to noise, weak or late amplification in the signal. Repeat the
sample. If the problem persists, contact Technical Service.
EC505 Insufficient information to determine whether amplification was present. If the problem
persists, contact Technical Service.
EC515 Internal control amplification is not within specification. Result is invalid, repeat the
sample. If the problem persists, contact Technical Service.
* In the case of one SARS-CoV-2 target positive/one SARS-CoV-2 target negative, result is suggestive of: 1) a sample at concentrations
near or below the limit of detection of the test, 2) a mutation in one of the target regions, or 3) other factors.
INVALID RESULTS
In case of an “Invalid” result, re-test the sample with a new Reaction Mix vial from the same kit or a new kit. If the problem is
unresolved, contact the DiaSorin Molecular Technical Services department. Contact information can be found on the last page of
this document.
LIMITATIONS
1. For Emergency Use Authorization Only use only.
2. For in vitro diagnostic use.
3. For professional use only.
4. Testing of nasal swabs even if collected by a healthcare provider is limited to patients with symptoms of COVID-19.
5. Not for screening.
6. False-negative results may occur if the viruses are present at a level that is below the analytical sensitivity of the assay or if
the virus has genomic mutations, insertions, deletions, or rearrangements or if performed very early in the course of illness.
7. As with other tests, false-positive results may occur. Repeat testing or testing with a different device may be indicated in
some settings.
8. This test is a qualitative test and does not provide the quantitative value of detected organisms present.
®
9. Information on the kit barcode can only be transferred into the LIAISON MDX Studio Software Studio through a bar-code
scanner. If the scanner is not working, or if you are unable to transfer the information for any reason, contact DiaSorin
Molecular Technical Services.
However, to assist clinical laboratories using the Simplexa™ COVID-19 Direct, the relevant Conditions of Authorization are listed
below:
1
A. Authorized laboratories using Simplexa™ COVID-19 Direct will include with result reports of Simplexa™ COVID-19, all
authorized Fact Sheets. Under exigent circumstances, other appropriate methods for disseminating these Fact Sheets may
be used, which may include mass media.
B. Authorized laboratories using Simplexa™ COVID-19 Direct will use Simplexa™ COVID-19 Direct as outlined in the
Instructions for Use. Deviations from the authorized procedures, including the authorized instruments, authorized extraction
methods, authorized clinical specimen types, authorized control materials, authorized other ancillary reagents and authorized
materials required to use Simplexa™ COVID-19 Direct are not permitted.
C. Authorized laboratories that receive Simplexa™ COVID-19 Direct will notify the relevant public health authorities of their intent
to run Simplexa™ COVID-19 Direct prior to initiating testing.
D. Authorized laboratories using Simplexa™ COVID-19 Direct will have a process in place for reporting test results to healthcare
providers and relevant public health authorities, as appropriate.
E. Authorized laboratories will collect information on the performance of Simplexa™ COVID-19 Direct and report to DMD/OHT7-
OIR/OPEQ/CDRH (via email: [email protected]) and DiaSorin Molecular (via phone: (800) 838-4548) any
suspected occurrence of false positive or false negative results and significant deviations from the established performance
characteristics of Simplexa™ COVID-19 Direct of which they become aware.
F. All laboratory personnel using Simplexa™ COVID-19 Direct must be appropriately trained in RT-PCR techniques and use
appropriate laboratory and personal protective equipment when handling this kit, and use Simplexa™ COVID-19 Direct in
accordance with the authorized labeling.
1
The letter of authorization refers to, “United States (U. S.) laboratories certified under the Clinical Laboratory Improvement
Amendments of 1988 (CLIA), 42 U.S.C. §263a, to perform high and moderate complexity tests” as “authorized laboratories.”
Simplexa™ COVID-19 Direct — Page 6
PERFORMANCE CHARACTERISTICS
CLINICAL EVALUATION
The clinical performance of the Simplexa™ COVID-19 Direct assays was established in multi-site clinical evaluation. Fresh clinical
NPS specimens were tested with the Simplexa™ COVID-19 Direct assay at three (3) different clinical sites from February 2020 to
March 2020. For each of the sites, an established comparator was used. Sites 1 and 3 used the same comparator while Site 2 used
a different comparator. Negative individually collected and positive contrived NS or NW specimens were tested internally with the
Simplexa™ COVID-19 Direct assay in April or May 2020. Contrived samples were prepared by spiking heat-inactivated 2019-
nCoV/USA-WA1/2020 strain (ATCC® VR-1986HK™) into individual negative NS or NW specimens. BAL specimens, diluted 1:1 with
Sputasol, were tested with the Simplexa™ COVID-19 Direct assay at one clinical site using an established comparator.
,
Comparator Agreement* **
Simplexa™ COVID-19 Direct
Positive (+) Negative (-) N/N (%)
Positive (+) 1 0 PPA: 1/1 (100%)
Site 1 Negative (-) 0 20 NPA: 20/20 (100%)
Site Total 1 20
Positive (+) 11 0 PPA: 11/11 (100%)
NPS
The final LoD for NPS, according to the assay results interpretation, is 500 copies/mL.
Analytical Sensitivity/Limit of Detection for Viral Genomic RNA in UTM with RNasin
S gene (FAM) ORF1ab (JOE)
COVID-19
genomic RNA Interpretation % Detection % Detection
Mean Ct ± SD Mean Ct ± SD
Copies/mL (# Detected / # (# Detected / #
(%CV) (%CV)
Tested) Tested)
100% (48/48)
2000 Positive 100% (48/48) 31.0 ± 0.64 (2.1%) 100% (48/48) 31.3 ± 0.74 (2.4%)
100% (48/48)
1000 Positive 95.8% (46/48) 32.4 ± 1.01 (3.1%) 93.8% (45/48) 32.7 ± 1.08 (3.3%)
100% (48/48)
500 Positive 95.8% (46/48) 33.4 ± 1.31 (3.9%) 70.8% (34/48) 33.9 ± 0.98 (2.9%)
The Limit of Detection (LoD) for NS was determined to be the lowest detectable concentration of inactivated titered COVID-19 viral
particles, strain 2019-nCoV/USA-WA1/2020, at which ≥ 95% of all replicates tested positive according to the results interpretation
algorithm in pooled negative nasal swab specimens in UTM. Initially, the tentative LoD was identified with serial dilutions of the viral
particles tested in four (4) replicates. The lowest concentration at which all replicates were positive was interpreted as the tentative
LoD. The LoD was then confirmed by testing twenty (20) replicates with concentrations at the tentative limit of detection. The final
LoD was confirmed to be the lowest concentration resulting in positive detection with a minimum 95% positivity.
Simplexa™ COVID-19 Direct — Page 7
The final LoD for NS, according to the assay results interpretation, is 242 copies/mL.
COVID-19
Genome Interpretation % Detection % Detection
Copies / mL (# Detected / # Mean Ct ± SD (# Detected / # Mean Ct ± SD
Tested) (%CV) Tested) (%CV)
100% (20/20)
242 Positive 80% (16/20) 34.0 ± 0.83 (2.4%) 80% (16/20) 32.9 ± 0.75 (2.3%)
The Limit of Detection (LoD) for NW was determined to be the lowest detectable concentration of inactivated titered COVID-19 viral
particles, strain 2019-nCoV/USA-WA1/2020, at which ≥ 95% of all replicates tested positive in pooled negative NW specimen matrix.
Initially, the tentative LoD was identified with serial dilutions of the viral particles tested in four (4) replicates. The lowest
concentration at which all replicates were positive was interpreted as the tentative LoD. The LoD was then confirmed by testing
twenty (20) replicates with concentrations at the tentative limit of detection. The final LoD was confirmed to be the lowest
concentration resulting in positive detection with a minimum 95% positivity.
The final LoD for NW, according to the assay results interpretation, is 500 copies/mL.
Analytical Sensitivity/Limit of Detection for Inactivated Viral Particles in Nasal Wash/Aspirate matrix
S gene (FAM) ORF1ab (JOE)
COVID-19
Genome Interpretation % Detection % Detection
Mean Ct ± SD Mean Ct ± SD
Copies / mL (# Detected / # (# Detected / #
(%CV) (%CV)
Tested) Tested)
100% (20/20)
500 85.0% (17/20) 33.1 ± 1.01 (3.0%) 95.0% (19/20) 32.3 ± 0.89 (2.8%)
Positive
The Limit of Detection (LoD) for BAL was determined to be the lowest detectable concentration of inactivated titered COVID-19 viral
particles, strain 2019-nCoV/USA-WA1/2020, at which ≥ 95% of all replicates tested positive in pooled negative BAL matrix. Initially,
the tentative LoD was identified with serial dilutions of the viral particles tested in four (4) replicates. The lowest concentration at
which all replicates were positive was interpreted as the tentative LoD. The LoD was then confirmed by testing twenty (20) replicates
with concentrations at the tentative limit of detection. The final LoD was confirmed to be the lowest concentration resulting in positive
detection with a minimum 95% positivity.
The final LoD for BAL, according to the assay results interpretation, is 1208 copies/mL.
100% (20/20)
1208 Positive 90.0% (18/20) 32.8 ± 0.99 (3.0%) 95% (19/20) 32.2 ± 0.96 (3.0%)
REACTIVITY/INCLUSIVITY
An in silico inclusivity analysis of the Simplexa™ COVID-19 Direct primers and probes was performed. All primer sets designed for
detection of the ORF1ab and S gene were tested against the complete available SARS-CoV-2 genome sequence. The analysis
demonstrated that the regions recognized by the designed primers and probes have 100% homology with all available SARS-CoV-2
sequences from the National Center for Biotechnology Information (NCBI) and Global Initiative on Sharing Avian Influenza Data
(GISAID) databases/databanks.
CROSS REACTIVITY
Cross-reactivity of the Simplexa™ COVID-19 Direct assay was evaluated using both in silico analysis and by testing whole
organisms or purified nucleic acid from other organisms. Test specimens for laboratory testing were prepared by spiking cultured
6
isolates/inactivated organisms/purified nucleic acids (whole genome) (i.e., a minimum of 10 CFU/mL or higher for bacteria and
5
10 TCID50 /mL or PFU/mL or higher for viruses) into negative matrix (UTM) and determining cross reactivity based on three
®
replicates. RNasin was added to UTM for specimens containing extracted RNA. The results from the cross-reactivity, both in silico
and wet testing, are summarized below.
COVID-19
IC Qualitative
Qualitative %
Potential Interfering Tested % Detection
Active Ingredient Detection
Substance Concentration (# Detected /
(# Detected /
#Tested)
#Tested)
Antibiotic nasal ointment Mupirocin 6.6 mg/mL 100% (3/3) 100% (3/3)
Luffa Opperculata,
Galphimia glauca,
Nasal gel 5% (w/v) 100% (3/3) 100% (3/3)
histaminum
hydrochloricum
Homeopathic allergy
Not Applicable 10% (v/v) 100% (3/3) 100% (3/3)
relief medicine
Nasal spray or drops Oxymetazoline 15% (v/v) 100% (3/3) 100% (3/3)
Bovine submaxillary
Mucin 60 μg/mL 100% (3/3) 100% (3/3)
gland mucin, type I-S
REFERENCES
1. Cui J, Li F, Shi ZL. Nat Rev Microbiol. 2019 Mar;17(3):181-192. doi: 10.1038/s41579-018-0118-9.
2. World Health Organization. Coronavirus. https://www.who.int/health-topics/coronavirus
3. Centers for Disease Control and Prevention. Coronavirus. https://www.cdc.gov/coronavirus/general-information.html
4. Cheng, Z.J., Shan, J. 2019 Novel coronavirus: where we are and what we know. Infection (2020).
https://doi.org/10.1007/s15010-020-01401-y
5. Centers for Disease Control and Prevention. Coronavirus Disease 2019 (COVID-19). https://www.cdc.gov/coronavirus/2019-
ncov/about/index.html
6. US Department of Health and Human Services PHS/CDC/NIH. Biosafety in microbiology and biomedical laboratories,
Washington DC: US Government Printing Office, 2007.
7. MM3-A2 Molecular diagnostic methods for infectious disease; approved guideline, 2nd ed. Wayne, PA: Clinical Laboratory
Standards Institute, 2006.
Simplexa™ COVID-19 Direct — Page 11
GLOSSARY
*ISO 15223-1