Professional Documents
Culture Documents
Templifier
Templifier
McQuay offers two innovative methods of saving energy by • Elevating water temperatures from a ground source to higher
obtaining hot water from the cooling cycle or other waste heat temperatures for space heating
source: the Templifier™ product and Centrifugal Chillers with
• Applications where fossil fuel is not economical, available or
Heat Recovery Condensers. Both products save significant energy
desirable for emission reasons
by converting readily available or usually discarded heat to more
useful, higher temperatures for efficiently heating the building or
domestic hot water. Economic Considerations
For heat recovery chillers to be effective, a sufficient
The Coefficient of Performance (COP) concept is what quantity of chilled water load is required when heating is
makes these systems economically practical. They offer COPs required. Templifiers require a continuous source of lower
ranging up to 8 or higher; meaning that when one unit of temperature waste heat when higher temperature heating is
purchased electric power is combined with seven units of waste needed.
heat, the result is 8 units of useful heat.
For example, a hospital is an excellent candidate where
continuous simultaneous heating and cooling occur. Hospitals
A Cost-Effective Investment for Your
have large domestic hot water needs and large amounts of
Application conditioned outside air. Conversely, a department store is not a
In the right applications, the savings from waste heat
candidate for heat recovery or a Templifier unit. The store is
recovery can have a payback of less than two years. In addition,
either heating or cooling (rarely simultaneously) with small
ASHRAE 90.1-1999 Energy Standard (6.3.6.2 Heat Recovery for
domestic water heating loads.
Water Heating) requires that recovered heat be used for service
hot water heating and reheat in many buildings.
2
McQuay Templifier Water Heaters
A unique solution for efficient hot water heating
Templifier Water Heaters remove heat in their evaporator from a waste heat source. By using the mechanical refrigeration
cycle, the low-grade heat in the evaporator is increased to a higher, more useful temperature in the condenser and delivered to
the heat load. A common application is to use the leaving condenser water from a traditional chiller at 95°F (35°C) as the heat
source. The Templifier unit can then elevate the waste heat temperature and supply heat up to 160°F (71°C), efficiently making
this hot water available for many practical uses, while reducing energy costs.
• Heats water more economically than fossil fuel fired boilers or electric resistance heaters.
• Can off-load overloaded boilers and/or cooling towers, thereby delaying or eliminating a capital expenditure required to
increase their capacity.
3
Templifier Water Heater System Operation
The system above is typical of a Templifier Water Heater recovering cooling load heat rejection from a conventional chiller’s
condenser water on the way to the cooling tower. The unit is sized to meet the heating load and often takes only a small part of the
condenser water flow; consequently, the bypass line around it. The cooling tower rejects any leftover heat to the atmosphere.
Templifier Water Heaters are controlled by the heating load and cool the warm source water in the evaporator as required by the
heating load. They generally do not make “chilled water”, but extract heat from sources such as cooling tower water, ground water,
solar heated water or industrial waste streams. Unlike a heat recovery chiller, they are controlled by the heating load and therefore only
use the amount of energy required to meet the load.
Templifier Water Heaters can be justified in new construction or retrofits, paying for themselves out of energy cost savings,
compared to fossil fuel boilers or electric resistance heaters.
4
Typical Templifier Applications
5
McQuay Heat Recovery Chillers
The useful heating output of these units can vary from zero (all heat
to the tower) to all of the heat (cooling load plus the compressor power),
converted to useful heat.
Tower
Heat Recovery Connections All of the heat rejection of the chiller is at the elevated heating water
Connections
temperature. These units are optimized economically when most of the
total heat rejection is utilized for useful heating, most of the time.
The electric cost of the heat is all the incremental compressor input power required to make the hot water; i.e., the power at
the high water temperature, minus the power that would be required for a conventional chiller operating at a lower, optimized tower
water temperature. Remember that all the compressor power is at the higher kW per ton.
• Reduced fossil fuel use. A Btu of energy from natural gas or oil
produces much more useful heat when used to generate 20
COP of electricity than when used in a boiler. Often the electric
energy is nuclear or hydroelectric sourced, meaning no fossil
fuel at all is used for heating.
6
Heat Recovery Centrifugal Chiller System Operation
The temperature of the heating water is controlled indirectly by controlling the tower water temperature. The temperature
controller positions the tower bypass valve to establish the desired hot water temperature. Since both condenser bundles are in
the same refrigerant gas stream, they will both leave the condenser at the same temperature.
type, and let the program do the system simulation. The following operating
conditions improve the economic feasibility:
• As warm as possible source water for Templifier units or chilled water for
heat recovery chillers.
• Output hot water temperature as low as possible.
• Constant availability of a cooling load for heat recovery chillers or heat
©2 m
co
source for Templifier units. 00
2M
c Q ua
y Inter national, www.m
cqu
ay.
7
Technical Specifications