V23809-K15-C10 V23809-K15-C310: 5 V 3.3 V 1300 NM Single Mode 1.3 GBD Gigabit Ethernet Transceiver 1X9
V23809-K15-C10 V23809-K15-C310: 5 V 3.3 V 1300 NM Single Mode 1.3 GBD Gigabit Ethernet Transceiver 1X9
5V
3.3 V V23809-K15-C310
1300 nm Single Mode 1.3 GBd
Gigabit Ethernet Transceiver 1x9
Preliminary Data Sheet
●
11x
●
0.25 typ. ∅.004 M
●
(1.6±0.1)
●
.020 typ.
.063±.004 (b)
●
Z
8x 2.54=20.32
●
0.25 typ.
8x .100=.800
●
.010 typ.
●
1 2 3 4 5 6 7 8 9
●
Rx
●
(25.4±0.1)
●
●
12.7 (2.54)
∅0.3 M A SC
●
RECEPTACLE 2x
8x .100=.800 (2.54)
●
Tx
20.32 .075±.004
●
.100 .800
●
The transmitter converts electrical PECL compati- Saturation (Average Power) PSAT –3
ble serial data (TD and TDnot) into optical serial Signal Detect Assert Level(4) PSDA TBD
data. It contains a laser driver circuit which drives
Signal Detect Deassert Level(5) PSDD TBD
the modulation and bias current of the laser diode.
The currents are controlled by a power control cir- Signal Detect Hysteresis PSDA–PSDD 1.5 dB
cuit to guarantee a constant output power of the
Output LO Voltage(6) VOL-VCC –1950 –1600 mV
laser over temperature and aging. The power con-
trol uses the output of the monitor pin diode Output HI Voltage(6) VOH-VCC –980 –720
(mechanically built into the laser coupling unit) for Output Data Rise/Fall Time, t ,t 375 ps
the controlling function to prevent the laser power R F
20–80%
from exceeding the operating limits.
Return Loss of Receiver ARL 12 dB
This module assures single fault condition with an
integrated automatic shutdown circuit, which dis- Notes
ables the laser when it detects transmitter failures. 1. Into single mode fiber, 9 µm diameter
A reset is only possible by turning the power off, 2. Laser power is shut down if power supply is below VTH and switched on if power
then on again. supply is above VTH after Tres.
3. Minimum average optical power at which the BER is less than 1x10E-12 or lower.
The transceiver contains a supervisory circuit to
Measured with a 27-1 NRZ PRBS and ER=9 dB.
control the power supply. This circuit makes an
4. An increase in optical power above the specified level will cause the SIGNAL
internal reset signal whenever the supply voltage
DETECT output to switch from a LO state to a HI state.
declines below the reset threshold. It keeps the
5. A decrease in optical power below the specified level will cause the SIGNAL
reset signal active for at least 140 milliseconds
DETECT to change from a HI state to a LO state.
after the voltage has risen above the reset thresh-
6. PECL 10K compatible. Load is 50 Ω into VCC –2 V. Measured under DC conditions.
old. During this time the laser is inactive.
For dynamic measurements a tolerance of 50 mV should be added. VCC=5 V.
LASER SAFETY
This single mode transceiver is a Class 1 laser product. It com-
plies with IEC 825-1 and FDA 21 CFR 1040.10 and 1040.11. Laser Data
The transceiver must be operated under the recommended Wavelength 1300 nm
operating conditions.
Total output power (as defined by
Caution IEC: 50 mm aperture at 10 cm dis- less than 2 mW
The use of optical instruments with this product will tance)
increase eye hazard!
Total output power (as defined by
General Restrictions FDA: 7 mm aperture at 20 cm dis- less than 180 µW
tance)
Classification is only valid if the module is operated within the
specified temperature and voltage limits. The system using the Beam divergence 4°
Figure 3. Schematic
82R
82R
82R
R1 R3 R5 R7
C1 C2
RD
TXD RDN GND GND
VCC–TX
TXDN SD
VCC-TX L2
130R
200R
130R
130R
130R
R1/3/5/7=82 Ohm
R2 R4 R9 R8
R2/4/6/8=130 Ohm C3 C4
VCC-RX
R9=200 Ohm R6
Transceiver GND GNDGND
GNDGND GND GND
The power supply filtering is required for good EMI perfor- The transceiver contains an automatic shutdown circuit. Reset
mance. Use short tracks from the inductor L1/L2 to the module is only possible when the power is turned off, then on again
VCC-RX/VCC-TX. (VCCTX switched below VTH).