Professional Documents
Culture Documents
Ba281 en PDF
Ba281 en PDF
2011 · BA 281-EN
V
V-VTN 16 | 26 | 41
V-Serie
V-Series
Drehschieber
Rotary Vane
Table of contents
Table of contents
1 Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Supplier documentation and accompanying documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5 Directives, standards, laws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.6 Symbols and meaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.7 Technical terms and meaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.8 Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Warning instruction markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4 Unacceptable operating modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5 Personal qualifications and training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.6 Safety-conscious work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.7 Safety notes for the operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.8 Safety instructions for installing, commissioning and maintenance . . . . . . . . . . . . . . . . . . . . . . 9
2.9 Guarantee conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.1 Preparing for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.3 Connecting pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.4 Control and relief valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.5 Connecting the motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
9 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1 Foreword
1.1 Principles
1.4 Abbreviations
Fig. Figure
V-VTN Vacuum pump
3
m /h Pumping capacity
mbar (abs.) Final vacuum, operating vacuum
Symbol Explanation
Condition, pre-requisite
#### Instructions, action
a), b),... Instructions in several steps
Results
[-> 14] Cross reference with page number
Information, note
Safety symbol
Warns of potential risk of injury
Obey all the safety instructions with this symbol in order to avoid injury
and death.
Term Explanation
Machine Pump and motor combination ready to be connected
Motor Pump drive motor
Vacuum pump Machine to create a vacuum
Rotary vane Machine’s design or active principle
Vacuum pump volume flow related to the condition in the suction con-
Pumping capacity
nection
Final pressure (abs.) The maximum vacuum that a pump reaches when the suction opening is
closed. Given as absolute pressure.
Permanent vacuum The vacuum or the suction range at which the pump operates perma-
nently.
The permanent vacuum or intake pressure is ≥ than the final vacuum and
< than the atmospheric pressure..
The noise emitted at a specific loading given as a figure, sound pressure
Noise emission
level dB(A) as per EN ISO 3744.
1.8 Copyright
2 Safety
The manufacturer is not responsible for damage if
you do not follow all of this documentation.
2.2 General
WARNING
WARNING
1 Eyebolt
3.2 Storage
NOTICE
3.3 Disposal
WARNING
V-VTN (01)
C1
B
A
E
F
F
N G
V-VTN (02)
C
O N
G1 G
4.1.1 Datenschild
4.2 Description
The V-VTN model range has a connecting thread on the suction side and an exhaust silencer on the pres-
sure side. The aspirated air is cleaned by an inbuilt fine micro filter.
The motor and the pump have a common shaft.
The vacuum pumps V-VTN are located in a plastic sound cover. Inside the sound cover is also a fan that
provides cooling.
The V-VTN (02) has a vacuum regulating valve fitted as standard (Fig. 2/C) that enables the vacuum to be set
to the required values which have an upper limit.
These dry running rotary vane vacuum pumps V-VTN 16 to V-VTN 41 are suitable for evacuating closed sys-
tems and for a permanent vacuum in the intake pressure range 150 - 1000 mbars (abs.).
The pumping capacity with unrestricted suction is 15, 25 and 40 m3/h at 50 Hz. Data sheet D 281 shows the
dependency of the pumping capacity on the intake pressure
These dry running machines are suitable for conveying air with a relative humidity of 30 - 90%.
If the unit is switched on more frequently (at regular intervals of about 10 times an hour) or at
higher ambient temperatures and intake temperatures, the excess temperature limit of the motor
winding and the bearings may be exceeded.
Please contact the manufacturer should the unit be used under such conditions.
If it is installed in the open air the unit must be protected from environmental influences, (e.g. by a
protective roof).
5 Installation
5.1 Preparing for installation
To remove the outlet grid (Fig. 3/G) and the inlet grating (Fig. 3/G1) at least 30 cm of space must
be available for maintenance work. You must also ensure that the cooling air inlets (Fig. 2/E) and
cooling air outlets (Fig. 2/F) must be at least 10 cm away from the nearest wall (outgoing cooling
air must not be sucked in again).
5.2 Installation
NOTICE
It must be possible to install the machine on a firm foundation without anchoring. When installing
on a substructure we recommend fixing with flexible buffers.
NOTICE
NOTICE
NOTICE
DANGER
NOTICE
Power supply
The conditions at the installation location must match
the information on the motor data plate. Without
derating the following is permissible:
• ± 5% voltage deviation
• ± 2% Frequency deviation
WARNING
Improper use
May lead to severe or fatal injuries. Therefore be
sure to obey the safety instructions.
CAUTION
Noise emission
The highest noise pressure levels measured as
per EN ISO 3744 are given in Section 9.
When spending a long time in the vicinity of the
running machine use ear protectors to avoid per-
manent damage to your hearing.
NOTICE
NOTICE
DANGER
WARNING
Regular maintenance work must be carried out in order to ensure operational safety.
Maintenance intervals also depend on the operational demands on the machine.
With any work observe the safety instructions described in Section 2.8 “Safety notes for installation, com-
missioning and maintenance”.
The whole unit should always be kept in a clean condition.
b G s m e
m Knurled knob
s Screw cap
Die Filterpatrone (Fig. 5/e) für Saugluft ist monatlich
oder je nach Verunreinigung öfters durch Ausblasen
von innen nach außen zu reinigen. In spite of clean-
ing the filter its separation efficiency will continue to
deteriorate. Therefore the filters should be replaced
every six months.
Changing filters:
Unscrew the outlet grid (5/G).
Undo the screw cap (Fig. 5/s) and the knurled knob
(Fig. 5/m). Remove and clean or replace filter car-
tridges (Fig. 5/e). Reassemble in reverse order.
WARNING
1 Filterpatrone
2 Druckluft
Z Y
O1
b
NOTICE
NOTICE
Machine is switched Mains voltage/ Frequency Check by qualified electrician Section 5.5
off by the motor pro- does not correspond with the
tection switch motor data
Connection to motor terminal
board is not correct
Motor protection switch is not
set correctly
Motor protection switch is Use a motor protection switch
triggered too quickly with an overload-dependent
delayed switch off that takes
into consideration the short
term excess current at start
up (version with short circuit
and overload trigger as per
VDE 0660 Part 2 orIEC 947-4)
The regulating valve is dirty so Clean or replace the regulat- Section 7.2
that the permissible vacuum ing valve Section 7.4
value is exceeded.
Pumping capacity is The intake filter is dirty Clean or replace the intake Section 7.2.1
insufficient filter Section 7.4
The suction pipe is too long or Check the hose or the pipe Section 5.3
too narrow
Machine or system leaking Check the pipework and Section 7.2
screw connections for leaks
and to ensure that they are
firmly seated.
Blades are damaged Replace blades Section 7.2.2
Section 7.4
Final pressure (max. Machine or system leaking Check the pipework and Section 7.2
vacuum) is not screw connections for leaks
reached and to ensure that they are
firmly seated.
Blades are worn or damaged Replace blades Section 7.2.2
Section 7.4
Machine gets too hot Ambient or intake temperature Ensure it is being used prop- Section 2.3
is too high erly
Cooling air supply is ob- Check environmental condi- Section 5.1
structed tions
Clean ventilation slots Section 7.2
The regulating valve is dirty so Clean or replace the regulat- Section 7.2
that the permissible vacuum ing valve Section 7.4
value is exceeded.
The machine makes The compressor housing is Repair by manufacturer or Elmo Rietschle
an abnormal noise worn (chatter marks) authorised workshop Service
The regulating valve is vibrat- Replace the valve Section 7.4
ing
Blades are damaged Replace blades Section 7.2.2
Section 7.4
Please contact Elmo Rietschle Service for other malfunctions or those that cannot be eliminated.
9 Technical Data
V-VTN 16 26 41
NOTICE
Gardner Denver
Schopfheim GmbH
Roggenbachstraße 58
79650 Schopfheim · Deutschland
Tel. +49 7622 392-0
Fax +49 7622 392-300
The following harmonized and national standards and specifications are applied:
EN 1012-1:1996 Compressors and vacuum pumps — Safety requirements — Part 1: Compressors
These declarations of conformity are invalid when the machine has been modified without prior ap-
proval by us and the approval has been documented in writing.
*) Microbiological, explosive or radioactively contaminated vacuum pumps/ components will only be accepted
with proof that they have been cleaned properly.
Type of toxic substance or process-related, dangerous reaction products with which the vacuum pumps/
components came into contact:
Trade name, manufacturer's Chemical Hazard Action to be taken if toxic First aid in the event of
product name name class substances are released accidents
1
2
3
4
Personal protection measures:
Company:
Street: Post code/ Town:
Phone: Fax:
Name (in capitals) Position: