The Fresnel Equations and Brewster's Law: Equipment
The Fresnel Equations and Brewster's Law: Equipment
Equipment
Optical bench pivot, two 1 meter optical benches, green laser at 543.5 nm, 2 10cm
diameter polarizers, rectangular polarizer, LX-02 photo-detector in optical mount, thick acrylic
block, thick glass block, Phillips multimeter, laser mount, sunglasses.
Purpose
Theory
k = 2π / λ , (2)
λ being the wavelength.
The purpose of this lab is to explore
the properties the electric field in (1) at the
interface between two media with indices of
refraction ni and nt . In general, there will
be an incident, reflected and transmitted
wave (figure 1), which in certain cases
reduce to incident and reflected or incident
and transmitted only. Recall that the angles
of the transmitted and reflected beams are
described by the law of reflection and Snell’s
law. This however tells us nothing about the
amplitudes of the reflected and transmitted Figure 1
electric fields. These latter properties are
defined by the Fresnel equations, which we review below.
First note that any plane wave may be represented as a superposition of two orthogonal
linearly polarized waves. By decomposing the electric field into linearly polarized light parallel and
perpendicular to the plane of incidence, we can apply the boundary conditions at the interface for
each case. The components of the electric and magnetic fields which are tangent to the surface
must be continuous across the boundary.
We begin by concentrating on the case shown in figure 1, i.e. the light wave polarized in
the plane of incidence1. For the electric field the continuity relation becomes
1
By convention, the polarization direction of a light wave that of the electric (not magnetic) field
vector.
− Ei cosθ i + Er cosθ i = − Et cosθ t (3)
Bi Br Bt
+ = (4)
µ1 µ1 µ2
where the law of reflection has been used to set θ r = θ i and we took into account that the
r r r r r r
vectors E , B , k are mutually orthogonal with E × B oriented along k . Here, µ is the permeability
of the material. Further taking into account the fact that in an electromagnetic wave and
nα Eα ∝ Bα (with α = i, r , t and nα being the refraction index of the material through which the
corresponding wave is propagating) we can write equation (4) as:
ni nt
( Ei + Er ) = Et . (5)
µi µt
Combining with equation (3), we arrive at the Fresnel equations for the wave polarized in the
plane of incidence:
nt cos θ i − ni cos θ t
r|| = (6)
nt cos θ i + ni cos θ t
2ni cos θi
t|| = , (7)
nt cosθ i + ni cosθ t
where we’ve supposed that we are in a non-magnetic material ( µ = 1 ) and defined the
amplitude reflection/transmission coefficients:
Er
r= (8)
Ei
E
t= t (9)
Ei
as the ratios of the amplitude of the reflected electric field to the amplitude of the incident electric
field.
In the case that the electric field is parallel to the plane of incidence, in much the same
way, we derive the second pair of Fresnel equations:
ni cos θ i − nt cos θ t
r⊥ = (10)
ni cos θ i + nt cos θ t
2ni cosθ i
t⊥ = (11)
ni cos θ i + nt cos θ t
Equations (6) and (10) may be conveniently expressed using Snell’s law where they become:
sin(θ i − θ t )
r⊥ = − (12)
sin(θ i + θ t )
tan(θ i − θ t )
r|| = (13)
tan(θ i + θ t )
The reflectance (intensity reflection coefficient) is the square of the amplitude reflection
coefficient:
R = r2 . (14)
sin 2 (θ i − θ t )
R⊥ = (15)
sin 2 (θ i + θ t )
tan 2 (θ i − θ t )
R|| = . (16)
tan 2 (θ i + θ t )
Consider now the case in which light is traveling from a medium of lower to higher index
of refraction (say, an air/glass interface). Since in this
case, θ i > θ t , (15) is never zero. However, the right
π
hand side of equation (16) vanishes when θi + θt =
2
in which case the denominator becomes infinite. At this
point, all incident light which is polarized in the plane
tangent to the plane of incidence is transmitted. The
value of θ i at which this occurs is known as Brewster’s
Angle θB .
Writing Snell’s law at Brewster’s angle,
π
ni sin θ B = nt sin θ t = nt sin( − θ B ) = nt cosθ B ,
2
or
nt
tan θ B = (17)
ni
2
Sir David Brewster (1781-1868) is mostly remembered for his invention of the
kaleidoscope and for optical improvements of the microscope. However, his main experiments
were on the theory of light and its uses. His first paper, "Some Properties of Light", was published
in 1813. Brewster's Law was named after him in 1814 when he made measurements on the
angle of maximum polarization using biaxial crystals. He was awarded all three of the principal
medals of the Royal Society for his optical research. These were the Copley medal in 1815, the
Rumford medal in 1818, and the Royal medal in 1830. He was also knighted in 1831.
Brewster’s Law may be understood by the following intuitive argument: the electric field
vector is transverse to the forward direction. However, at the point where the light polarized in the
plane of incidence starts to enter the glass the vibrations in the
transmitted wave happen to be parallel to the OR ray in Figure 3.
Elementary molecular dipoles inside the material also oscillate
along OR, and cannot produce a “reflected” electromagnetic
wave propagating in the same direction.
This means that only the component polarized normal to
the incident plane, SOR, or parallel to the surface, will be
reflected. At this point, even if the incident wave has both
polarization components (or its polarization its random), ray OR
is completely horizontally polarized and the electric field vector is
restricted to the plane that is parallel to the reflected surface.
This 100% linear polarization can only occur at one angle,
because this circumstance is restricted by the fact that the angle between the reflected ray, OR,
and the refracted ray, OT, has to be 90o.
A graph of the reflectivity (15)-(16) for the air-glass
interface as a function of the angle of incidence is shown in
Figure 4. At normal incidence, the parallel and perpendicular
polarization waves are physically identical, and have the
same reflectivity. Notice that even though the glass is
transparent, 4% of the light is still reflected. However, as θ i
increases, the parallel component drops and the
perpendicular component rises, until at the Brewster's angle
their values are approximately 0% and 15% of the initial
intensity of the light respectively. At an incident angle of 90o,
all of the incident light is reflected, so the substance acts as
a mirror.
The Fresnel equations can be tested by using a
pivoting lab bench to vary the incident angle of laser light
onto a reflecting surface and measuring the reflected
intensity. A photodetector is used in this lab to measure the
light intensity. The photodetector is calibrated to generate a
voltage proportional to the light intensity, which is then
measured with a multimeter. A polarizer between the
dielectric surface and the photodetector is used to select the parallel and perpendicular
components of the reflected light.
Experimental Procedure
1. The theoretical index of refraction for the crown glass and acrylic used in this lab are 1.61 and
1.49 respectively. With these values, use Snell’s Law for θ t , in equations (15) and (16) to make a
theoretical plot of the Fresnel Equations similar to figure 4.
2. Throughout this experiment ensure that the apparatus is aligned so that both the reflected and
transmitted laser beams are pointed away from the other students, and always keep track of
where the beams are. The laser you will be using for this experiment will itself produce polarized
light. Place the laser, polarizer, and detector onto the same optical bench. Turn on the laser,
voltmeter and the photodetector. Make sure the voltmeter is set to mV setting, and that the
detector is set to the 0.1mV = 1Lux setting.
3. The first task is to calibrate the polarizers spatially, and with respect to one another. Since in
this experiment, you will need to measure light parallel and perpendicular to the plane of
incidence which is determined by your set-up, it is important to know what value on the polarizers
correspond to the ⊥ (vertical) and || (horizontal) planes. The rectangular polarizer has its plane
of transmission along the
longer side. Send the laser
through one of the “round”
polarizers and the rectangular
sheet polarizer oriented
vertically. Place a paper card
behind both polarizers. Rotate
the round polarizer until the
transmission through both
polarizers is minimized. Make
a note of the rotation angle of
your polarizer. This angle
corresponds to a horizontally
polarized wave. Repeat this
procedure with the second
“round” polarizer.
4. Set up the bench as in figure 4 with the glass slider in the holder. Rotate polarizer 1 to transmit
45° polarization. This will ensure that the light incident onto your glass block has both parallel and
perpendicular components. If there is little or no light transmitted through the polarizer at 45°,
rotate the laser until a sufficient amount of light is showing.
5. Set Polarizer 2 to transmit horizontally polarized light. Measure the dependence of the reflected
intensity on the angle of incidence for this angle varied between 20o to 160o. Take at least 20
data points. Note that the protractor on the pivoting bench reads twice the actual value of θ i as
seen in figure 5. Note as well that the height of the beam may change because of the lab desks
being uneven. If this occurs, change the height of the detector so that the beam is hitting the
center of the face of the photodetector. This is necessary because the photodetector does not
have uniform sensitivity across its face.
6. Set Polarizer 2 and the detector on the first optical bench. Measure the intensity transmitted
through both polarizers. Use this value to normalize the data obtained in step 5. Plot the
normalized data on top of the theoretical curve obtained in step 1.
8. By means of direct observation with a naked eye, find the angle at which the reflection of the
parallel polarization wave is minimized. This is your Brewster angle. Determine the index of
refraction from equation (17).
9. At the experimental Brewster's angle, take the polarizer off the optical bench. Rotate the
sunglasses provided between the block and the detector (as if it were taking the place of the
polarizer). Record observations made.
10. Repeat steps 5-7 with the other material (acrylic vs. glass).
11. In step five, the polarizer was placed after the reflecting slide, for analysis. However, the
polarizations in question are independent of one another and so the transmission or reflection of
a given component does not affect its orthogonal polarization component. Due to this linearity of
the optics, a post-selection of the polarization should be equivalent to a pre-selection. Verify this
by placing the polarizer before the slide and repeating some of the measurements.
12. After measurements are completed, remember to turn off the photodetector or else the
batteries will run out.
Error Analysis
3. A table of values obtained in step 5 for both polarizations and both materials. Show both the
raw data and that normalized to the maximum intensity found in step 6.
4. On the theoretical plot of the Fresnel equations plot the data points taken in the experiment
with error bars.
5. A value for Brewster’s angle from step 8 with errors. A value for the index of refraction for each
plate with error.
6. Discuss the observations made with the sunglasses. Are the sunglasses polarized? What is
the purpose of making polarized sunglasses? Explain the significance of which axis the
sunglasses are polarized at.