Professional Documents
Culture Documents
Crown Amplifiers Catalog PDF
Crown Amplifiers Catalog PDF
®
INSTALLED SOUND
CTs 2-Channel Series
CTs Multi-Channel Series
CTs Multi-Channel with CobraNetTM
CDi Series
DSi Series
AMPLIFIERS INSTALLED SOUND
CTs Series: The New Standard
CTs 600, CTs 1200, CTs 2000, CTs 3000
Foundation
`` FEATURES
• High power density. All two channel
models in a 2U chassis.
• New Crown Switching Power Supply
for lighter weight.
• Selectable “Constant-Voltage” or
low-impedance operation per channel.
• 100V direct outputs on all models.
• Fully PIP2-compatible.
POWER OUTPUT*
2-ohm Dual 4-ohm Dual 8-ohm Dual 16-ohm Dual 70V Dual 100V Dual 4-ohm 8-ohm 16-ohm 100V 140V 200V
Models (per channel) (per channel) (per channel) (per channel) (per channel) (per channel) Bridge Bridge Bridge Bridge Bridge Bridge
CTs 600 150W 300W 300W 300W 300W 300W‡ 300W 600W 600W 600W‡ 600W 600W‡
CTs 1200 250W 600W 600W 300W 600W 600W‡ 500W 1,200W 1,200W 1,200W‡ 1,200W 1,200W‡
CTs 2000 1,000W 1,000W 1,000W 625W 1,000W 1,000W 2,000W 2,000W 2,000W 2,000W 2,000W 2,000W
CTs 3000 1,500W 1,500W 1,250W 625W 1,500W 1,500W 3,000W 3,000W 2,500W 3,000W 3,000W 3,000W
*Maximum average power in watts at rated THD, 20 Hz - 20 kHz. ‡With T-170V or TP-170V.
`` SPECIFICATIONS
Frequency Response (at 1 watt, 20 Hz - 20 Ready Indicator: Green LED, one per channel, Highpass Filter: One 3-position switch per
kHz): ±0.25 dB. illuminates when the channel is initialized and channel selects between OFF, 35Hz and 70Hz
Signal to Noise Ratio below rated power (20 ready to produce audio output. Indicator is off 3rd-order filters.
Hz to 20 kHz): 105 dB A-weighted. when PIP puts the amplifier in standby mode via “Y” Input Switch: When set to ON, this switch
the control system. parallels the input signals of the two channels
Total Harmonic Distortion (THD) at full rated
power, from 20 Hz to 20 kHz: CTs 600/1200: Signal Indicators: Three green LEDs per chan- for use when the input signal is mono. Also can
< 0.1%. CTs 2000/3000 < 0.35%. nel indicate the amplifier’s input and output be used to daisy-chain the signal to another
signal levels. amplifier.
Damping Factor: 10 Hz to 100 Hz: > 3000.
Crosstalk (below rated power, 20 Hz to 1 kHz): Signal: input signal is above –40 dBu. Ventilation Grille: Front-to-rear forced airflow.
> 80 dB. –20 dB: amplifier output is 20 dB below clipping.
Common Mode Rejection (CMR) (20 Hz to 1
–10 dB: amplifier output is 10 dB below clipping. Options
kHz): 50 dB. Clip Indicator: Red LED, one per channel, PIP2 modules, including the PIP-Lite, PIP-USP3,
illuminates when the channel’s output signal and PIP-USP3/CN.
DC Output Offset: < ±2 mV.
reaches the onset of audible clipping. The Clip
Input Impedance (nominal): 10 kilohms bal- Indicator also will illuminate during Thermal Protection Systems
anced, 5 kilohms unbalanced. Level Control (TLC) limiting or when the input Thermal Level Control (TLC): If an amplifier
Maximum Input Level: +20 dBu before input compressor/limiter is protecting the amplifier channel starts to overheat, the TLC circuit will
compression, +32 dBu absolute maximum. from input overload. engage the input compressor. By compressing
Load Impedance: (Note: Safe with all types of Thermal Indicator: Red LED, one per channel, the input, the amplifier will not generate as much
loads) illuminates when the channel has shut down, heat and will have a chance to cool down.
CTs 600/1200 or is very near shutting down, due to thermal Junction Temperature Simulation (JTS): In the
Stereo: 2/4/8/16 ohms, 70V, 100V stress or overload. CTs 600/1200, if excess power is demanded,
Bridge Mono: 4/8/16 ohms, 140V. Fault Indicator: Red LED, one per channel, JTS circuitry limits the drive level of the output
CTs 2000/3000 flashes when the amplifier output channel has devices to a safe range, preventing damage.
Stereo: 2/4/8/16 ohms, 70V, 100V stopped operating. Fault: The amplifier will light the Fault LED if the
Bridge Mono: 4/8/16 ohms, 140V, 200V. Data Indicator: Yellow LED indicates control amplifier output stage stops operating.
Voltage Gain (at maximum level setting): data activity (if the amplifier is equipped with AC Under-/Over-Voltage Protection: If the AC
8/4 ohm operation, 1.4V sensitivity an IQ-PIP2 module, and connected to a control line voltage drops below 25% or rises above
CTs 600 35:1 (31 dB) system). 15% of the nominal operating voltage of the
CTs 1200 50:1 (34 dB) Power Indicator: Blue LED indicates amplifier amplifier, the amplifier’s power supply turns
CTs 2000 63.9:1 (36 dB) has been turned on and AC power is available. off and the blue Power LED flashes. The ampli-
CTs 3000 71.4:1 (37 dB). The LED will flash when the AC line voltage is fier will turn back on when the AC line voltage
26 dB: 20:1 (26 dB). 15% above or 25% below the nominal rated returns to safe operating levels.
70V operation, 1.4V sensitivity or 100V value. Circuit Breaker: This breaker protects the ampli-
operation, 2.0V sensitivity: 50:1 (34 dB). Cooling Vents: Front-to-rear forced airflow. fier from excessive AC current draw.
AC Line Voltage and Frequency Configurations Power Switch: Push-on / push-off switch. DC Output Servo: The output servo circuit
Available (±10%): 120VAC/60Hz, 230VAC/50 Hz. protects your drivers by eliminating DC offset,
Power Draw at Idle (120VAC mains): Back Panel Controls and Connectors even in the presence of very large asymmetrical
signals.
CTs 600/1200: 24W (standby mode) Power Cord Connector: Standard 15 amp IEC
CTs 2000/3000: 35W (standby mode). inlet. Voltage is indicated above IEC inlet. In-rush Limiting: A soft-start circuit in the
Cooling: Continuously variable speed forced air, power supply minimizes the amplifier’s current
Reset Switch: Resets the circuit breaker that
front-to-back airflow. draw during power-on.
protects the power supply.
Dimensions: 19 in. (48.3 cm) W x 3.5 in. (8.9 Variable-speed Fan: Two continuously variable
Speaker Connectors: One four-pole touch-proof
cm) H x 14.25 in. (36.2 cm) D. speed fans direct the airflow through the ampli-
terminal strip. Accepts up to 10 AWG terminal
Weight: Net, Shipping forks. fier for cooling.
CTs 600: 22.8 lb (10.3 kg), 27.7 lb (12.6 kg) Input Connectors: Balanced 2-pin terminal block
CTs 1200: 23.4 lb (10.6 kg), 28.3 lb (12.8 kg) Regulatory Certifications
connector, one per channel, on the standard
CTs 2000: 27.0 lb (12.2 kg), 32.0 lb (14.5 kg) PIP2-BBY module.
CTs 3000: 27.7 lb (12.6 kg), 32.7 lb (14.8 kg).
Channel Level Control: One 21-position
Front Panel Controls and Indicators detented rotary attenuator per channel, ranging Other Applications
Bridge Mode Indicator: Yellow LED illuminates from minus infinity (–70 dB) to 0 dB gain.
when the rear-panel Mode Switch is set to the Mode Switch: Two-position switch is used to
“Bridge” position. select the amplifier’s mode of operation: Dual or
Bridge-Mono.
9/07 136317-2B
INSTALLED SOUND
C rown’s CTs Series amplifiers provide exceptional performance, flexibility and value for installed
sound applications. CTs Series amplifiers feature independent selection of high and low impedance
operation for a specific channel, plus power levels and features that were carefully chosen to match
the requirements of fixed install design. Easy integration with HiQnet™ and CobraNet™ allows CTs
amplifiers to deliver a comprehensive lineup of monitoring and control features along with digital audio
transport for an award-winning digital audio solution.
AMPLIFIERS INSTALLED SOUND
CTs Multi-Channel Series: The New Standard
CTs 4200, CTs 8200
Flexibility
`` FEATURES
• High power density: Four-channel model in a 2U chassis,
eight-channel model in a 3U chassis.
• New Crown Switching Power Supply for lighter weight.
• Selectable “Constant-Voltage” or low-impedance (4/8 ohm)
operation per channel-pair.
• 100V direct outputs.
• New “FIT” (Fault Isolation Topology) circuitry isolates fault
conditions without affecting neighboring channels.
• Accept new MC accessory modules.
POWER OUTPUT*
All channels driven 1 channel driven All channel pairs driven 1 channel pair driven
Models 4-ohm Dual 8-ohm Dual 70V Dual 4-ohm Dual 8-ohm Dual 70V Dual 8-ohm Bridge 16-ohm Bridge 100V Bridge 8-ohm Bridge 16-ohm Bridge 100V Bridge
† † † †
CTs 4200 260W 180W 220W 270W 220W 250W 520W 400W 220W 560W 440W 250W
† † † †
CTs 8200 200W 160W 200W 270W 220W 250W 400W 320W 200W 540W 440W 250W
*Maximum average power in watts at 1kHz at 0.1% THD.
†Constant Voltage full-bandwidth power ratings support 100 Hz to 20 kHz due to automatic high-pass filters.
`` SPECIFICATIONS
Frequency Response (at 1 watt, 20 Hz - 20 kHz): Signal Indicator: Green LED, one per channel, Protection Systems
±0.5 dB. illuminates to indicate the presence of analog input Thermal Level Control (TLC): If an amplifier chan-
signals above –40 dBu. nel starts to overheat, the TLC circuit will engage
Phase Response (at 1 watt, 10 Hz - 20 kHz): ±35°.
Clip Indicator: Red LED, one per channel, illumi- that channel’s input compressor. By compress-
Signal to Noise Ratio below rated power (20 Hz to nates when the THD of the channel’s output signal ing the input, the amplifier will not generate as
20 kHz): 100 dB unweighted. rises to a level typically considered as the onset of much heat and will have a chance to cool down.
Total Harmonic Distortion (THD) at 1 watt, from audible clipping. The Clip Indicator also will illumi- The degree of compression is proportional to the
20 Hz to 20 kHz: < 0.05%. nate during Thermal Level Control (TLC) or input amount of overheating. If the channel becomes too
overload. hot for safe operation even after full TLC limiting,
Intermodulation Distortion (IMD) 60 Hz and 7 the channel will shut off, and the Thermal Indicator
kHz at 4:1, from 163 milliwatts to full bandwidth Thermal Indicator: Red LED, one per channel, for that channel will flash brightly to alert the user
power: < 0.05% (typical). flashes when a state of thermal stress or overload that a state of thermal stress or overload has cause
Damping Factor: 10 Hz to 400 Hz: >180. has caused the channel to shut down. If the power the channel to shut down.
supply goes into thermal overload, all channel LEDs
Crosstalk (below rated power, 20 Hz to 1 kHz): > will flash. FIT (Fault Isolation Topology): Isolates faults within
80 dB. affected channels.
Fault Indicator: Red LED, one per channel, flashes
Common Mode Rejection (CMR) (20 Hz to 1 kHz): Fault: If an amplifier channel requires service, the
when a fault condition has occurred in the channel.
> 50 dB. corresponding Fault indicator will illuminate to alert
Ventilation Grille: Front-to-rear forced airflow. the user of this condition. If this occurs, return the
DC Output Offset (shorted input): < ±5 mV. amplifier to the Crown factory or to an authorized
Data Indicator: Yellow LED indicates IQ Loop data
Input Impedance (nominal): 20 kilohms balanced, activity (if the amplifier is equipped with an IQ-MC Crown service center.
10 kilohms unbalanced. module, and connected to an IQ Loop). High-Pass Filter: A fixed 35-Hz (70-Hz in CTs 4200)
Maximum Input Level (before input compression): Power Indicator: Blue LED indicates amplifier has high-pass filter per channel pair is automatically
+ 20 dBu. been turned on and AC power is available. Indica- inserted when the mode switch is set to either of
Load Impedance: (Note: Safe with all types of tor also flashes if the amplifier shuts off due to an the constant-voltage settings. The high-pass filter
loads) under-/over-voltage condition on the AC mains. corner frequency in the CTs 8200 can be set to 70
Hz, or bypassed, with a service option.
Stereo: 4/8 and 25 ohms (70V) Power Switch: Amplifier is on when the switch is in
Bridge Mono: 8/16 and 50 ohms (100V) the IN position. AC Under-/Over-Voltage Protection: If the AC
line voltage varies out of an acceptable range, the
Voltage Gain (at maximum level setting), 1.4V Back Panel Controls and Connectors amplifier’s power supply turns off and the blue
sensitivity, AC Power Cord Connector: IEC inlet, type 320; Power LED flashes. The amplifier will turn back on
4/8 Ohm Operation: 20:1 (26 dB); 100/120VAC units: 15A; when the AC line voltage returns to safe operating
70V Operation: 50:1 (34 dB) 220/230/240VAC units: 10A. levels.
100V Operation: 71.4:1 (37 dB) Voltage is indicated above IEC inlet. Under-Voltage Over-Voltage
Models
AC Line Voltage and Frequency Configurations Output Connectors: One four-pole terminal strip Limit Limit
Available (±10%): 120V/60 Hz, 220/230/240V/50 for every two channels with touch-proof cover. 100VAC
Hz. Accepts up to 10 AWG terminal forks. 90VAC 110VAC
(CTs 8200 only)
Power Draw at Idle (120VAC mains, all channels Accessory Panel: CTs 4200 accepts an optional 120 VAC units 108VAC 132VAC
in 4/8 ohm mode): 58W. VCA-MC4A module. CTs 8200 accepts an optional
VCA-MC8 module. 220V/230V/240V
Power Draw at Idle (120VAC mains, all channels 198VAC 264VAC
Channel Level Controls: One 21-position detented units
in 70V mode): 77W.
rotary potentiometer per channel, ranging from
Cooling: Continuously variable speed forced air, Power Fuse: A fuse protects the amplifier from
infinity (–70 dB) to 0 dB attenuation.
front-to-back airflow. excessive AC current draw.
Input Connectors: Removable Phoenix-style barrier
Dimensions (Width, Height, Depth): Inrush Limiting: A soft-start circuit in the power
connectors for balanced input. Also can be used as
CTs 4200: 19 in. (48.3 cm) W x 3.5 in. (8.9 cm) a CobraNet input or a backup for CobraNet. supply minimizes the amplifier’s current draw
H x 16.25 in. (41.3 cm) D. during power-on.
Mode Switch: Used on each consecutive pair of
CTs 8200: 19 in. (48.3 cm) W x 5.25 in. (13.3 channels, this four-position switch is used to select Variable-speed Fan: Continuously variable speed
cm) H x 16.25 in. (41.3 cm) D. the amplifier’s mode of operation: Dual 8/4 ohms, fan directs the airflow through the amplifier for
Dual 70V, Bridge-Mono 16/8 ohms, and Bridge- cooling.
Weight (Net, Shipping):
Mono 100V. Regulatory Certifications
CTs 4200: 27 lb 8 oz (12.5 kg),
32 lb (14.5 kg) Cooling Vents: Front-to-rear forced airflow.
CTs 8200: 36 lb 6 oz (16.5 kg), Options
47 lb (21.3 kg). Control Modules: VCA-MC4A: VCA module for CTs
4200A. VCA-MC8: VCA module for CTs 8200. Other Applications
Front Panel Controls and Indicators Wall-mount level control panels for use with VCA
Bridge Mode Indicator: Yellow LED, one per module: 1-VCAP: Single-gang panel with 1 VCA
channel pair, illuminates when the channel pair’s channel volume control. 4-VCAP: Two-gang panel
Mode Switch is set to the “Bridge” position. If Mode with 4 VCA channel volume controls.
switch is changed while amplifier is powered up,
Bridge LED will flash, indicating that the amplifier T-170V: This is an autoformer that allows 100V
must be powered off and on to reset the Mode. output from the amplifier, and allows other ampli-
fiers without direct constant voltage output to be
Ready Indicator: Green LED, one per channel, easily integrated into distributed systems.
illuminates when the channel is initialized and ready
to produce audio output. TP-170V: This is a rack-mountable panel with four
autoformers as described above.
8/07 136318-1K
INSTALLED SOUND
C rown’s CTs Multi-Channel Series offers wide flexibility for a wide range of installed sound applica-
tions. CTs Multi-Channel Series amplifiers offer independent selection of high- and low-impedance
operation for each channel pair, making these amps ideal for multi-zone installations.
AMPLIFIERS INSTALLED SOUND
CTs Multi-Channel Series: With CobraNet
CTs 4200USP/CN, CTs 8200USP/CN
CobraNet Capable
TM
POWER OUTPUT*
All channels driven 1 channel driven All channel pairs driven 1 channel pair driven
Models 4-ohm Dual 8-ohm Dual 70V Dual 4-ohm Dual 8-ohm Dual 70V Dual 8-ohm Bridge 16-ohm Bridge 100V Bridge 8-ohm Bridge 16-ohm Bridge 100V Bridge
† † † †
CTs 4200USP/CN 260W 180W 220W 270W 220W 250W 520W 400W 220W 560W 440W 250W
† † † †
CTs 8200USP/CN 200W 160W 200W 270W 220W 250W 400W 320W 200W 540W 440W 250W
*Maximum average power in watts at 1kHz at 0.1% THD.
†Constant Voltage full-bandwidth power ratings support 100 Hz to 20 kHz due to automatic high-pass filters.
`` SPECIFICATIONS
USP/CN CobraNet Module Specifications IQ Data Indicator D/A and A/D Conversion: 24 bit.
(for amplifier specifications, see the CTs Multi- Flashes when the module receives a valid Latency:
Channel Series pages) command that is addressed to the CTs 4200 DSP processing: 1 ms or 1000 µs.
USP/CN and CTs 8200USP/CN. Digital-to-analog conversion: 250 µs.
Connectors:
Switches: Analog-to-digital conversion: 250 µs.
AUX Connector
Reset/Preset Switch Amplifier: 100 µs.
Configurable for AUX input, AUX output and
Used to change presets, restore settings to Total: 1.6 ms or 1000 µs.
Listen Bus. Listen Bus is also supported
through CobraNet. factory default or restore all the presets to Dynamic Range: 103 dB typical (A-weighted,
the factory defaults. During operation of the 20Hz–20kHz, audio sourced from muted
Network Connector
switch, the Data indicator flashes as an aid to CobraNet channel).
The dual RJ45 CobraNet connectors allow
a Primary & Secondary connection to the the user. Accessible with a straightened paper Distortion: < 0.1% THD+N, 20Hz–20kHz.
100Mb Ethernet network. Should the Primary clip through the rear panel, the switch selects
the next user preset if pressed for less than Frequency Response: ± 0.5 dB, 20Hz–20kHz.
connection lose link activity with the network,
2 seconds, resets the module to preset “0” if Input/Output Monitor Accuracy: Typically ±1dB.
the input module will automatically switch to
the Secondary connection to ensure uninter- pressed for more than 2 seconds. Maximum Input Level: + 20 dBu.
rupted audio and control. The indicators on General:
the RJ45 connectors display network infor- Regulatory Certifications
Memory Backup: Non-volatile FLASH memo-
mation concerning the Ethernet and CobraNet ries for backup of run-time parameters, pre-
connections. sets, and program storage.
Indicators: Communications: 100Mb Fast Ethernet con-
Preset Indicator forming to IEEE 802.3. Other Applications
Signals the number of the current preset, if Overall Audio Performance:
active, by flashing a series of flashes equal to DSP Processing: Two processors, 32 bit,
the current preset number. Floating Point, 724 µs latency.
CTs 8200USP/CN Back Panel (note USP/CN CobraNet™ module at top left)
2/08 139279-2
INSTALLED SOUND
T he Crown® CTs 4200USP/CN and CTs 8200USP/CN power amplifiers have an integrated 3rd genera-
tion, DSP-based input module. It connects the amplifier to a 100 Mbps Ethernet network allowing it
to be remotely controlled and monitored via System Architect™ software. In addition, the input module
allows the transport of real-time digital audio via CobraNet™ over the same Ethernet network. The
amplifiers connect to a HiQnet™ audio control/monitor network using standard 100 Mbps Ethernet
hardware (switches, Network Interface Cards, and cables). CobraNet™ audio is available over the same
100 Mbps Ethernet network, providing a simple-to-install, single-plug solution for audio distribution,
control, and monitoring.
AMPLIFIERS INSTALLED SOUND
CDi Series: 2/4/8 Ohm, 70V/100V per channel
CDi 1000, CDi 2000, CDi 4000, CDi 6000
Versatility
`` FEATURES
• Onboard digital signal processing includes crossovers,
EQ filters, delay, and output limiting.
• Computer connectivity via USB allows fast setup and
configuration with HiQnet™.
• Barrier strip outputs, removable Phoenix-style input.
• Extremely versatile, handling a wide range of speaker
impedances and outputs.
• Switch-mode universal power supply.
• Speaker presets for crossover frequencies, EQ, limiting,
compression, delay, and subharmonic synthesis.
POWER OUTPUT*
2-ohm Dual 4-ohm Dual 8-ohm Dual 70V Dual 4-ohm 100V‡ Dual 140V Bridge
Models (per channel) (per channel) (per channel) (per channel) Bridge (per channel)
5/09 139648-4
INSTALLED SOUND
T he CDi Series of Crown® amplifiers are professional tools designed and built for installed sound
applications. The series includes four models which are identical except for output power: CDi
1000, CDi 2000, CDi 4000 and CDi 6000. All are rugged and lightweight, and offer unmatched value
in their class. CDi-Series amplifiers feature an LCD screen with DSP speaker presets. Other features
include a switch-mode universal power supply, useful function indicators, proportional-speed fan-
assisted cooling, removable Phoenix-style inputs, barrier strip outputs for low-Z or 70V/140V loads,
short-circuit protection and more.
AMPLIFIERS INSTALLED SOUND
DSi Series: 2, 4, 8 ohm
DSi 1000, DSi 2000, DSi 4000, DSi 6000
One-touch
Performance
`` FEATURES
• Intuitive front-panel LCD screen, automatic presets for popular
JBL speaker systems for quick, easy configuration.
• Onboard digital signal processing includes crossovers, EQ filters,
delay, and output limiting.
• Computer connectivity via USB allows fast setup and configura-
tion with HiQnet™.
• Barrier strip outputs, removable Phoenix-style input.
• All models are THX®-approved.
POWER OUTPUT
2-ohm Dual 4-ohm Dual 8-ohm Dual 4-ohm 8-ohm
Models (per channel) (per channel) (per channel) Bridge Bridge
3/09 139622-3
INSTALLED SOUND
Echannel
ngineered from the ground up for unmatched quality and performance, the Crown DSi ®
Series of power amplifiers offers four models of 500W, 800W, 1200W and 2100W per
at 4 ohms. Onboard digital signal processing includes crossovers, EQ filters, delay
and output limiting. Rear panel HD-15 connector provides easy input/output connectivity
between DSi amplifiers and the new DSi-8M System Monitor. At the touch of a button,
Crown’s DSi cinema amplifiers deliver perfectly matched performance with each award-
winning JBL ScreenArray system, making this the ultimate cinema solution.
COMMERCIAL AUDIO
Preamplifier-Mixers
Amplifiers
Mixer-Amplifiers
XM Business Music Systems
COMMERCIAL AUDIO PREAMPLIFIER-MIXERS
14M, 28M
Adaptable
`` FEATURES
• 4 or 8 inputs, 1 or 2 output channels.
• Ideal for commercial and industrial use.
• Balanced Phoenix-type mic/line inputs; RCA inputs.
• Balanced Phoenix-type line outputs.
• Any input can be sent to any output.
• Priority muting.
• Independent bass and treble controls for each input.
Model Inputs System Zones
14M 4 Single-zone
28M 8 Two-zone
`` SPECIFICATIONS
Performance Tone Controls: Bass and Treble non-detented Line Out Connector: One 3-pin balanced Phoe-
Frequency Response (at line out): 20 Hz to 20
potentiometers on each input channel. Bass nix-type connector per output channel. Level
kHz +/- 1 dB.
±10 dB at 100 Hz, Treble ±10 dB at 10 kHz. controlled by master volume control.
Signal to Noise Ratio (master volume at
Power Indicator: Blue LED indicates power on. Input Connectors:
minimum): 100 dB.
Input Signal Presence Indicator: Green LED, Mic/Line Connector: 3-pin Phoenix-type, bal-
THD: 0.05% typical with 800 mV balanced anced, one per input channel.
one for each input channel, illuminates when
input, 1V output.
input signal exceeds –24 dBu (line) or –70 dBu Dual RCA Input Connector: For stereo music
Input Sensitivity (volts RMS for full output at (mic). signals, unbalanced, summed together, two
maximum gain): connectors per input channel.
Output Signal Presence Indicator: Green LED,
Balanced mic inputs: 3 mV. one for each output channel, illuminates when The tone generator has been omitted. Call
Balanced line inputs: 800 mV. output signal level exceeds 100 mV. Crown Tech Support if you have a tone genera-
RCA connectors: 400 mV. tor question.
Clip Indicators: Red LED, one per output
Input Impedance (nominal): channel. Illuminates at threshold of audible Mic/line Switch: Selects mic-level or line-level
Mic: 400 ohms. distortion. signals. One switch for each balanced input
Line: 100 kilohms.
Output Volume Controls: One per output chan-
RCA: 50 kilohms.
nel. Detented potentiometer with knob. Included Accessories
Crosstalk (all controls at “10”): –50 dB at Power cord
1kHz. Back Panel Controls and Connectors Detachable rack ears
Fuse: Protects the power supply. Phoenix-type connectors
Line Output Level (nominal): 1.2 V into 10 Spade lugs
kilohms. AC Power Inlet: Detachable IEC.
Phantom Power: 15 VDC. Auxiliary Power Input: 2-position terminal strip Dimensions
AC Line Voltages Available: for 24 VDC (±10%) backup power. Accepts up EIA Standard 19-inch (48.3-cm) rack mount
100V 50/60 Hz to 10 AWG terminal forks. width (EIA RS-310-B) with rack ears, 1.7-inch
120V 60 Hz Mixer Config Switch: A DIP switch with two (4.3-cm) height and 10.7-inch (27.18-cm) depth
220V 50/60 Hz functions: behind the mounting surface.
230V 50/60 Hz 1. Assigns an input as the priority input for
240V 50/60 Hz Weight
each output, thereby temporarily muting the Net Weight:
Operating Temperature/Humidity: 0° C to 40° remaining inputs. Muting is activated by contact 14M: 8.7 lb (3.9 kg)
C at 95% relative humidity (non-condensing). closure. 28M: 8.7 lb (3.9 kg)
Storage Temperature: –20° C to 85° C. 2. Global enable switch for phantom power. Shipping Weight:
Does not affect RCA inputs. Default position 14M: 14 lb (6.4 kg)
Front Panel Controls and Indicators is off. 28M: 14 lb (6.4 kg)
Power Switch: Pushbutton on-off switch.
Priority Connector: 3-pin Phoenix-type connec- Regulatory Certifications
The power switch does not affect the 24V DC
tor allows Input 1 or Input 5 (28M only) to mute
auxiliary power input.
other input signals by contact closure.
Input Volume Controls: Microphone/line, four
Input Routing Switch (28M only): DIP switches
in 14M, eight in 28M. Detented potentiometers
that assign each input signal to each output.
with knobs.
Two switches per input.
12/07 138119-1D
COMMERCIAL AUDIO
T he Crown® 14M and 28M are high-value mixers for commercial and industrial audio. The mixers
are part of Crown’s Commercial Audio Series, which also includes mixer-amplifiers and power
amplifiers. These low-cost units provide all necessary features in a simple building-block format. Some
applications include schools, hospitals, factories, restaurant/retail, houses of worship, fitness facilities,
A/V boardrooms, correctional facilities, and small offices. Typical uses are paging, background music,
security and evacuation instructions. Input routing allows each input to be assigned to any output. You
can add more mixers for more inputs, or add more power amps (or mixer-amps) to handle more zones.
Other features include priority muting and phantom power.
COMMERCIAL AUDIO AMPLIFIERS
180A, 280A, 1160A
Power Zone
`` FEATURES
• Ideal for commercial and industrial use.
• Balanced Phoenix-type line inputs; touch-proofed screw-terminal
speaker outputs.
• Advanced protection system includes output current limiting,
DC protection, circuit breaker/fuse, and thermal protection.
• 1 or 2 inputs; 1 to 2 amplifier output channels.
POWER OUTPUT*
Models 4-ohm 70V/100V Inputs System Zones
9/07 138118-2A
COMMERCIAL AUDIO
T
®
he Crown 180A, 280A and 1160A are high-value amplifiers for commercial and industrial audio.
They provide 4-ohm and constant-voltage outputs (70V and 100V). The amps are part of Crown’s
Commercial Audio Series, which also includes mixers and mixer-amps. These low-cost units provide
all necessary features in a simple building-block format.
COMMERCIAL AUDIO AMPLIFIERS
660A
6-Channel
`` FEATURES
• 6 inputs; 6 amplifier output channels.
• Balanced Phoenix-type line inputs; touch-proof screw-terminal speaker
outputs.
• Advanced protection system includes output current limiting,
DC protection, circuit breaker/fuse, and thermal protection.
• Ideal for commercial and industrial use.
POWER OUTPUT*
Model 4-ohm 70V/100V Inputs System Zones
THD: Less than 0.5% at rated power at 1 kHz. Volume Controls: One per output channel.
Detented potentiometer with knob. Included Accessories
Input Sensitivity (for full output at maximum Power cord
gain): 800 mV. Tone Controls: Bass and Treble non-detented Detachable rack ears
potentiometers on each channel. Bass ±10 dB Screws for rack ears
Input Impedance (nominal): 100 kilohms.
at 100 Hz, Treble ±10 dB at 10 kHz. Non-touch cover for output connectors
Minimum Load Impedance:
Phoenix-type connectors
100V output: 160 ohms. Back Panel Controls and Connectors
Spade lugs
70V output: 80 ohms. Reset Switch: Resets the circuit breaker that
4-ohm output: 4/8 ohms. protects the power supply. 220/230/240V units
Optional Accessories
Crosstalk (all controls at “10”): –70 dB at have a fuse instead.
1-VCAP remote volume control for one channel.
1kHz. Input Connectors: Detachable 3-pin Phoenix- 4-VCAP remote volume control for four chan-
Load Impedance: type, high-impedance balanced, one per chan- nels.
Ch. 1-4: 4 ohms and 70V/100V. nel.
Ch. 5-6: 4 ohms. AC Power Inlet: Detachable IEC. Dimensions
AC Line Voltages Available: Amplifier Outputs Connectors: One per EIA Standard 19-inch (48.3-cm) rack mount
100V 50/60 Hz channel, 4-position terminal strip with COM width (EIA RS-310-B) with rack ears, 3.5-inch
120V 60 Hz (Common), 4 ohms, 70V and 100V terminals (8.9-cm) height and 12.2-inch (31.0-cm) depth
220V 50/60 Hz for channels 1-4 and one 4-position terminal behind the mounting surface (not including non-
230V 50/60 Hz strip (4 ohms, + and – for each channel) for touch cover). 4.1 inches (10.5 cm) high includ-
240V 50/60 Hz channels 5 and 6. Accepts up to 10 AWG termi- ing feet. 13.9 inches (35.2 cm) deep from front
AC Voltage Tolerance: +10%/–20%. nal forks. Non-touch cover included. of knobs to back of non-touch cover.
Operating Temperature/Humidity: 0° C to 40° VCA Connector: Each pair of channels has a 4-
Weight
C at 95% relative humidity (non-condensing). pin Phoenix-type connector for two VCA control
lines of +10 VDC and ground. Compatible with Net Weight:
Storage Temperature: –20° C to 85° C. 30.3 lb (13.7 kg)
Crown 1-VCAP and 4-VCAP modules.
Shipping Weight:
Front Panel Controls and Indicators 35.3 lb (16.0 kg)
Cooling
Power Switch: Pushbutton on-off switch. Convection cooled.
Power Indicator: Blue LED indicates power on. Regulatory Certifications
11/08 139754-1B
COMMERCIAL AUDIO
T he Crown® 660A is a very flexible, high-value six-channel amplifier for commercial and industrial
audio. It provides 4-ohm and constant-voltage outputs (70V and 100V) on channels 1 through 4,
and 4-ohm outputs on channels 5 and 6. The 660A is a part of Crown’s Commercial Audio Series, which
also includes mixers and mixer-amps. These low-cost units provide all necessary features in a simple
building-block format.
COMMERCIAL AUDIO MIXER-AMPLIFIERS
180MA, 280MA, 1160MA
Practical
`` FEATURES
• 4 to 8 inputs, 1 to 2 amplifier output channels.
• Ideal for commercial and industrial use.
• Balanced Phoenix-type mic/line inputs; touch-proofed
screw-terminal speaker outputs.
• Any input can be sent to any output.
• Priority muting.
POWER OUTPUT*
Models 4-ohm 70V/100V Inputs System Zones
12/07 137964-2B
COMMERCIAL AUDIO
C rown’s Commercial Audio mixer/amplifiers deliver legendary Crown quality to the commercial audio
industry. These high-value mixer-amplifiers provide both 4-ohm and constant-voltage outputs (70V
and 100V) for use in a wide range of commercial applications including schools, hospitals, factories,
restaurant/retail, houses of worship, fitness facilities, A/V boardrooms, correctional facilities, and small
offices. Easily configured for a range of uses such as paging, background music, security, and evacua-
tion instructions, Crown’s Commercial Audio units are the smart choice for commercial sound.
COMMERCIAL AUDIO MIXER-AMPLIFIERS
135MA, 160MA
Practical
`` FEATURES
• 3 inputs and one 35W amplifier output channel in 135MA.
• 4 inputs and one 60W amplifier output channel in 160MA.
• Ideal for paging, background music, and music-on-hold.
• Voice-activated priority muting (VOX).
• Pre-amp outputs.
POWER OUTPUT*
Models 8-ohm 70V/100V Inputs System Zones
2/08 140498-1
COMMERCIAL AUDIO
C rown’s Commercial Audio mixer/amplifiers deliver legendary Crown quality to the commercial audio
industry. These high-value mixer-amplifiers provide both 8-ohm and constant-voltage outputs (70V
and 100V) for use in a wide range of commercial applications including schools, hospitals, factories,
restaurant/retail, houses of worship, fitness facilities, A/V boardrooms, correctional facilities, and small
offices. Easily configured for a range of uses such as paging, background music, security, and evacua-
tion instructions, Crown’s Commercial Audio units are the smart choice for commercial sound.
COMMERCIAL AUDIO MIXER-AMPLIFIERS
140MPA
POWER OUTPUT*
Model 4-ohm 25V/70V Inputs System Zones
140MPA 40W 40W 4 Single-zone
*Minimum guaranteed power in watts at 1 kHz with 0.5% THD.
`` SPECIFICATIONS
Performance Back Panel Controls, Connectors and VOX Threshold: Trim pot controls how loud the
Frequency Reponse (at 1 watt from 4-ohm Indicators voice must be before ducking occurs. Can be
tap): 50 Hz to 15 kHz ± 1 dB. Reset Switch: Resets the circuit breaker that set for no ducking.
Frequency Response (at line out): 50 Hz to 15 protects the power supply. Link In/Out Switch: Slide switch. When set to
kHz ± 1 dB. AC Power Inlet: Detachable IEC. IN, any signal applied to the Amp Input connec-
tor will be mixed with the input signal(s). When
Power Bandwidth (at 4-ohm tap, 2 dB below Amplifier Output Connector: 4-position termi- set to OUT, only the signal from the Amp Input
maxium 1 kHz power): 50 Hz to 20 kHz with nal strip with COM (Common), 4 ohms, 25V Connector will appear at the amplifier output.
< 0.5% THD. and 70V terminals. Accepts up to 10 AWG
terminal forks. Non-touch cover included. Priority Connector: 3-pin Phoenix-type connec-
Signal to Noise Ratio (ref. to rated power,
tor for push-to-talk mic contact closure. Input
master volume at minimum): >90 dB. Output VCA Connector: 4-pin Phoenix-type 1 is the priority input for the amplified output,
DC Output Offset: < ±5 mV. connector for two VCA control lines of +10 VDC so Input 1 ducks the other inputs. Threshold of
and ground. Compatible with Crown 1-VCAP activation depends on input voltage. Ducking
THD: < 0.5% at rated power at 1 kHz.
module. does not affect MOH outputs.
Input Sensitivity (for full output at maximum
Priority Connector: 3-pin Phoenix-type connec- Active Indicator: Illuminates when VOX ducking
gain):
tor for push-to-talk mic contact closure. is active.
Balanced mic inputs: 3 mV.
Preamp Line Out Connector: 3-pin balanced
Balanced line inputs: 800 mV.
Phoenix-type connector. Post master, pre-VCA. Cooling
RCA connectors: 400 mV. Convection cooled.
Level controlled by master volume control.
Input Impedance (nominal): Protection
MOH 1V Level Control: Trim pot adjusts level
Mic: 400 ohms. Current Limit Protection: Included.
for Music-On-Hold 1V output.
Line: 100 kilohms.
RCA: 50 kilohms. MOH 1W Level Control: Trim pot adjusts level Thermal Limit Protection: Over-temperature
for Music-On-Hold 1W output. thermal cutout.
Crosstalk: –70dB at 1kHz.
MOH SPI Indicator: Flashes when MOH signal DC-Fault Load Protection: Included.
Line Output Level (nominal): 1V into 10
is present. Turn On/Turn Off: No thumps or pops.
kilohms.
MOH 1V Phoenix Connector: 3-pin Phoenix
Phantom Power: 15 VDC. Included Accessories
connector for 1V, 600-ohm transformer-isolated
AC Line Voltages Available: Power cord
output.
120V/60Hz. Line voltage tolerance +15%, Detachable rack ears
MOH 1W Phoenix Connector: 3-pin Phoenix Screws for rack ears
–20%.
connector for 1W output. Non-touch cover for output connectors
Operating Temperature/Humidy: 0° C to 40° C Phoenix-type connectors
MOH 1V RCA Connector: Two mono RCA con-
at 95% relative humidity (non-condensing). Spade lugs
nectors for 1V output (in parallel with 600-ohm
Storage Temperature: –20° C to 85° C. connections so they are isolated).
Optional Accessories
Front Panel Controls and Indicators Balanced Input Connector: Detachable 3-pin 1-VCAP remote volume control
Power Switch: Pushbutton on-off switch. Phoenix style connector for balanced line-level
signals, one each for input channels 2-4. Dimensions
Input Volume Controls: Four controls, one per Width (without rack ears): 17.3 in. (43.8 cm).
input. Detented potentiometers with knobs. Balanced Input Connector: Detachable 3-pin Width (with rack ears): EIA Standard 19 in. W
Phoenix style connector for balanced mic-level (EIA RS-310-B).
Tone Controls: Bass and Treble non-detented
line-level signals, for input channel 1. Height (front panel): 3.5 in. (8.9 cm).
recessed potentiometer on each input channel.
Bass ±10 dB at 100 Hz, Treble ±10 dB at 10 Tel Connector: Transformer-isolated 600-ohm Height (including feet): 4.1 in. (10.5 cm).
kHz. input, summed into Input 1 for paging from a Depth (front panel to back panel): 12.2 in. (31.0
telephone system. cm).
Power Indicator: Blue LED indicates power on.
Dual RCA Input Connector: For stereo music Depth (front of knobs to back of non-touch
Input Signal Presence Indicator: Green LED, cover): 13.9 in. (35.2 cm).
signals, unbalanced, summed together, two
one for each input channel, illuminates when
connectors per input channel. Weight
input signal exceeds –40 dBu.
Amp Input Connector: 3-pin Phoenix-type, Net Weight:
Output Signal Presence Indicator: Green LED
high-impedance balanced. Used to link an 17 lb (7.7 kg).
illuminates when output signal level exceeds
additional mixer to the mixer-amplifier. Can be Shipping Weight:
100 mV (45 dB below full power) from the
used to connect an external processor. 22 lb (9.98 kg).
4-ohm tap.
Mic/line Switch: Selects mic-level or line-level
Clip Indicator: Red LED on output illuminates
signal for Input 1.
Regulatory Certifications
at threshold of audible distortion.
Phantom Power Switch: Turns phantom power
Master Output Volume Control: Detented
on or off for Input 1.
potentiometer with knob.
1/06 139430-1
COMMERCIAL AUDIO
T he Crown® 140MPA is a high-value mixer-amplifier for commercial audio. It provides 4-ohm and
constant-voltage outputs (25V and 70V). Typical uses are paging, background music, and music-
on-hold. The unit provides 4 inputs (each with a volume control) and a 40W amplifier output. Other
features include priority ducking, phantom power, and capability for remote volume control. Multiple
units can be linked.
COMMERCIAL AUDIO XM TUNER-MIXER-AMPLIFIERS
180MAx Pack (180MAx tuner-mixer-amplifier also available separately)
XM Enabled
`` FEATURES
• Programmable XM tuner with XM channel data display.
• Independent bass and treble controls for each input.
• Balanced Phoenix-type mic/line inputs; touch-proof screw-
terminal speaker outputs.
• Priority ducking, Music-On-Hold (MOH) outputs.
• 180 MAx Pack includes four JBL Control 1ST 2-way speak-
ers with 70V transformer and mounting brackets, remote
control and XM antenna.
POWER OUTPUT*
Model 4-ohm 25V/70V Inputs System Zones
COMMERCIAL AUDIO
T he Crown® 180MAx Pack is the first tuner-mixer-amplifier and loudspeaker system designed for
commercial use. It is designed for easy installation. Applications include restaurants, retail stores,
coffee shops and other commercial establishments. The system includes the Crown 180MAx tuner-
mixer-amplifier (also available separately), four JBL® Control® 1ST 2-way loudspeakers with built-in
70V transformers, XM antenna and a wireless remote control. Built into the 180MAx is an XM Radio
tuner that receives satellite radio stations with digital sound quality. The unit also accepts signals from
line, telephone, or microphone (phantom power included). Other features include bass and treble
controls, and priority ducking.
PORTABLE PA
XTi Series
XLS Series
AMPLIFIERS PORTABLE PA
XTi Series: World Class
XTi 1000, XTi 2000, XTi 4000, XTi 6000
World-Class
`` FEATURES
• Computer connectivity via USB allows fast setup and configuration
with HiQnet™.
• Integrated speaker presets with LCD front panel display.
• Extremely versatile, handling a wide range of speaker impedances
and outputs.
• Switch-mode universal power supply.
• Speaker presets for Crossover Frequencies, EQ, Limiting, and Delay.
• All products fill 2U rack spaces and set a new standard in
lightweight amps.
• Speakon® and binding post outputs, XLR inputs and loop-thrus.
• Comprehensive LED status per channel.
POWER OUTPUT
2-ohm Dual 4-ohm Dual 8-ohm Dual 4-ohm 8-ohm
Model (per channel) (per channel) (per channel) Bridge Bridge
12/08 139472-3
P O R TA B L E PA
T he XTi Series of Crown® amplifiers are professional tools designed and built for portable PA applica-
tions. The series includes four models which are similar except for output power: XTi 1000, 2000,
4000 and 6000. All are rugged and lightweight, and offer unmatched value in their class. XTi-Series
amplifiers feature an LCD screen with speaker presets for crossover frequencies, EQ, limiting, delay,
and a subharmonic synthesizer. Other features include a switch-mode universal power supply, useful
function indicators, proportional-speed fan-assisted cooling, XLR inputs, Speakon® and binding-post
outputs, short-circuit protection and more.
AMPLIFIERS PORTABLE PA
XLS-III Series: Performance and Flexibility
XLS1000, XLS1500, XLS2000, XLS2500
Innovation
`` FEATURES
• High Performance, Lightweight Class-D amplifier – weighs
less than 11 lbs.
• Integrated PureBand™ Crossover system ensures seamless
transitions from low to high frequency drivers.
• Integrated PeakX™ Limiters provide maximum output while
protecting your speakers.
• XLR, 1/4", RCA Inputs ensure compatibility with any source.
• 1/4" Inputs can be used as loop-thrus to distribute signal to
additional amplifiers.
POWER OUTPUT*
2-ohm Dual 4-ohm Dual 8-ohm Dual 8-ohm 4-ohm
Models (per channel) (per channel) (per channel) Bridge Bridge
Y
XLS1500, XLS2000, XLS2500: > 103 dB. limiter designed to provide maximum output Cooling: Internal heat sinks with forced-air
Total Harmonic Distortion (THD): < 0.5%. while protecting your loudspeakers. cooling for rapid, uniform heat dissipation.
Air Volume Requirements
AR
Intermodulation Distortion (IMD): Indicators
(60 Hz and 7 kHz at 4:1) from full rated Signal Presence Indicators: Two green LEDs, (per minute per unit): 80.15 ft³ (2.27 m³).
output to –30 dB: < 0.3%. one for each channel, illuminate when the Dimensions:EIA Standard 19-inch (48.3-cm)
Damping Factor (8 ohm) 10 Hz to 400 Hz: channel’s input signal exceeds –40 dBu. rack mount width (EIA RS-310-B), 3.5-inch
> 600. –10 Indicator: Green LED flashes when (8.9-cm) height.
Crosstalk (below rated 8 ohm power): output signal exceeds –10 dB below clip. XLS1000/1500: 8.10-inch (20.6-cm) depth.
IN
at 1 kHz: > 85 dB. XLS2000/2500: 10.35-inch (26.3-cm) depth.
–20 Indicator: Green LED flashes when
at 20 kHz: > 60 dB. output signal level exceeds –20 dB below clip. Weight
Input Impedance (nominal): Clip Indicators: Two red LEDs, one for each Net Weight:
20 kilohms balanced, 10 kilohms unbalanced. channel, illuminate when the channel’s output XLS1000: 8.6 lb (3.9 kg)
Load Impedance: 2 to 8 ohms per channel in
IM is being overdriven. XLS1500: 8.6 lb (3.9 kg)
XLS2000: 10.75 lb (4.9 kg)
Stereo, 4 to 8 ohms in Bridge Mono. Thermal Indicator: Two red LEDs, one
XLS2500: 10.75 lb (4.9 kg)
AC Line Voltage and Frequency for each channel, illuminate when thermal
Configurations Available (±10%): 120 VAC compression begins. Shipping Weight:
60 Hz, 100 VAC 50/60 Hz, 220 and 240 VAC XLS1000: 13.6 lb (6.2 kg)
EL
Input/Output XLS1500: 13.6 lb (6.2 kg)
50 Hz. Input Connectors: XLR (one per channel), XLS2000: 15.75 lb (7.1 kg)
Controls 1/4 inch (one per channel), and RCA (one per XLS2500: 15.75 lb (7.1 kg)
Level: Two front-panel rotary level controls, channel). The 1/4 inch inputs can be used
one for each channel. as loop-thrus to distribute signal to multiple Regulatory Certifications
amplifiers.
PR
P O R TA B L E PA
T ake command of center stage with Crown's new XLS amplifiers. The high-
performance class-D amplifier combined with its integrated PureBand™ Crossover
System deliver unmatched performance and sound; while its multiple inputs let
you plug in anything you want. PeakX™ Limiters effortlessly protect your speaker
investment, and at 11 pounds moving from show to show is nearly effortless.
Powerful, flexible, portable, and reliable – RUN THE SHOW with a power amplifier
designed to play hard all night long.
AMPLIFIERS PORTABLE PA
XLS Series: Affordable and Reliable
XLS 5000
Evolution
`` FEATURES
• Housed in a rugged, all-steel 3U chassis.
• Efficient forced-air fan prevents excessive thermal buildup.
• Electronically balanced XLR inputs; touchproof binding
post and Speakon outputs.
• Precision detented level controls, power switch, and four
LEDs, which indicate clip for each channel, power and fault
conditions.
POWER OUTPUT*
2-ohm Dual 4-ohm Dual 8-ohm Dual 8-ohm 4-ohm
Models (per channel) (per channel) (per channel) Bridge Bridge
3/08 139436-3B
P O R TA B L E PA
Macro-Tech i Series
AMPLIFIERS TOURING
I-Tech Series: Excellence Without Compromise
I-T4000, I-T6000, I-T8000
POWER OUTPUT*
20 mS BURST 2-ohm Dual 2-ohm Dual 4-ohm Dual 8-ohm Dual 4-ohm 8-ohm
Model 2-ohm Dual (per ch.) ( per channel) (per channel, 1 kHz) (per channel) (per channel) Bridge Bridge
MA-5000i 3,000W 2,000W 2,000W 2,500W 1,250W 4,000W 5,000W
MA-9000i 4,700W 2,800W 3,500W 3,500W 1,500W 5,600W 7,000W
MA-12000i 6,000W 3,750W 4,500W 4,500W 2,100W 7,500W 9,000W
*Guaranteed minimum power in watts at 20 Hz-20 kHz with 0.1% THD
`` SPECIFICATIONS
Summary Specifications Input Sensitivity (referenced to 8 ohm rated Back Panel Connectors, Controls,
Frequency Response (at 1 watt, 20 Hz - 20 output): Adjustable in 0.1V steps from 1.4V to and Indicators
kHz): ±0.25dB. 7.75V.
Connectors: Balanced XLR analog inputs, bal-
Signal to Noise Ratio below rated full-band- Required AC Mains: Universal AC input, 100- anced analog XLR loop-thru outputs, AES/EBU
width power, A-weighted: > 112 dB. 240VAC, 50/60 Hz (±15%). Maximum AC mains digital input, AES/EBU digital loop-thru output,
Total Harmonic Distortion (THD) at full rated voltage 277VAC. 4-Pole Speakon output connectors, binding
power: < 0.1%. AC Line Connector: Five cordsets supplied with post output connectors, power cord, EtherCon®
amplifier (USA, UK, European, Australia, India). Ethernet connector for networking via HiQnet or
Intermodulation Distortion (IMD) 60 Hz and CobraNet.
7 kHz at 4:1, from full rated output to –35 dB:
< 0.2%. Front Panel Indicators, Controls and Reset Switch/Circuit Breaker: If the current
Connectors draw of the amplifier exceeds safe limits, this
Damping Factor (20 Hz to 100 Hz at 8 ohms): breaker automatically disconnects the power
> 5000. Indicators: Bridge mode, Ready, Signal level,
supply from the AC mains. The switch resets the
Crosstalk (below rated power, 20 Hz to 1 kHz): Clip, Thermal error, Fault, Network data, Power,
circuit breaker.
> 80 dB. AC mains.
Preset Indicator: LED flashes to signal the
Common Mode Rejection (CMR) (20 Hz to 1 LCD Control Screen and Controls: These let
number of the current preset if active. LED is
kHz): > 70 dB typical. the user adjust the amplifier’s attenuation and
green if the preset values have not been changed
muting, configure the amp, set up and view
Latency (analog, digital inputs): 1.13 mS analog, once loaded. LED is yellow if the preset values
error monitoring (such as temperature and load
1.81 mS digital (96 kHz). have been changed since they were loaded.
supervision), set IP and HiQnet addresses from
A/D, D/A Converters: 24-bit 192 kHz Cirrus the front panel, and recall DSP presets. The
Logic. presets allow the user to quickly reconfigure the Construction
amp for various applications. Cooling: Dual-zone, microprocessor controlled,
Digital Input: AES/EBU, 24-bit, 32-96 kHz.
Onboard sample-rate converter. Level Controls (Encoders): Speed-sensitive continuously variable speed fans, front-to-back
rotary encoders, 0.5 dB steps, range 0 to –100 airflow.
Network: Onboard TCP/IQ and HiQnet, compat-
dB. These two knobs affect the Channel-1 and Dimensions: 19 in. (48.3 cm) W x 3.5 in. (8.9
ible with standard 100 Mb Ethernet hardware.
Channel-2 output levels. They also select Menu cm) H x 16.2 in. (41.1 cm) D.
DSP: 24-bit conversion with 32-bit, floating- items and adjust parameter values that are
point DSP processing. World-class IIR and Weight: 28 lbs (12.7 kg) net, 36 lbs (16.3 kg)
displayed on the LCD Control Screen.
linear phase FIR filters. Has 64 assignable filters shipping.
Power Switch: Push-on/push-off switch with
with 9 different filter types. Includes all-pass Included Accessories: Rear rack ears, rack
built-in green AC mains present indicator.
filters, over 2 seconds of delay available per screws, operation manual, power cords, foam
channel, and dual uncorrelated-noise and sine- USB 2.0 Connector: Accepts a USB drive to air filter.
wave generators. transfer presets from the drive to the amplifier
DSP, and vice versa.
Load Impedance: (Note: Safe with all types of Regulatory Certifications
loads) Stereo: 1/2/4/8/16 ohms. Bridge Mono:
2/4/8 ohms.
Other Applications
12/08 141259-1
T O U R I N G
C rown continues the tradition of excellence and innovation with the Crown® I-Tech HD Series,
delivering unmatched versatility, power and performance for touring sound applications. Featuring
onboard high-definition BSS OMNIDRIVEHD™ DSP with 24-bit, 192 kHz Cirrus Logic SHARC A/D and
D/A converters, the I-Tech HD Series also offers a new software interface that provides easier system-
level changes, and includes a configuration wizard. Providing up to 9 kW continuous power in a 2U rack
space and delivering the highest output voltage in the industry, the I-Tech HD Series outperforms all the
competition, even our own.
AMPLIFIERS TOURING
Macro-Tech i Series: The Legend Continues
Macro-Tech i Series
POWER OUTPUT*
20 mS BURST 2-ohm Dual 2-ohm Dual 4-ohm Dual 8-ohm Dual 4-ohm 8-ohm
Model 2-ohm Dual (per ch.) ( per channel) (per channel, 1 kHz) (per channel) (per channel) Bridge Bridge
MA-5000i 3,000W 2,000W 2,000W 2,500W 1,250W 4,000W 5,000W
MA-9000i 4,700W 2,800W 3,500W 3,500W 1,500W 5,600W 7,000W
MA-12000i 6,000W 3,750W 4,500W 4,500W 2,100W 7,500W 9,000W
*Guaranteed minimum power in watts at 20 Hz-20 kHz with 0.1% THD
`` SPECIFICATIONS
Performance Power Indicator: Blue LED indicates amplifier Preset Indicator: Green/yellow LED flashes to
Frequency Response has been turned on and AC power is available. signal the number of the current preset. LED is
(at 1 watt, 20 Hz - 20 kHz into 8 ohms): The LED will flash when the AC line voltage is green if current preset is active, or is yellow if
±0.25 dB. 10% above or below the nominal rated value. current preset is modified.
Signal to Noise Ratio Data Indicator: Yellow LED on front panel Input Sensitivity Switch: Three-position switch
(below rated full-bandwidth power, A-weighted): indicates network data activity. Data indicator providing 1.4V, 32 dB, and 26 dB settings for
>112 dB. flashes only when the amplifier is polled for both channels.
Total Harmonic Distortion (THD) data, or is polled to see whether it is online
(at 2 watts into 8 ohms): < 0.1%.
Firmware/Software
Power Switch: Push-on/push-off switch with
Firmware can be updated at www.crownaudio.
Total Harmonic Distortion (THD) built-in green AC mains present indicator.
com > Support > Downloads.
Plus Noise (at full rated power): Volume Control: Precision detented attenuator
Software features: Same as PIP-Lite module
< 0.35%, 20 Hz to 20 kHz. with 31 steps, press-and-hold mute function.
(except no Listen Bus): User Presets, Clip Event
Intermodulation Distortion (IMD) Volume Control LED Ring: A ring of green LEDs Monitor, Input Signal Level Monitor, Output
(60 Hz and 7 kHz at 4:1, around each volume control show the position Signal Level Monitor, Thermal Headroom Level
from full rated output to –30 dB): < 0.35%. of the control. Entire ring flashes when channel Monitor, Power/Standby Control, Signal Mute,
Damping Factor (20 Hz to 100 Hz at 8 ohms): is muted. Can be converted to be a level meter. Polarity Inverter, Input Signal Fader, Dynamic
> 5000. Back Panel Controls, Indicators and Gain Monitors (Ghost Faders), Amplifier
Crosstalk (below rated power, 20 Hz to 1 kHz): Information, User and Channel Labels, Amplifier
Connectors Mode, Amplifier Output Mode, Line Voltage
> 80 dB.
Power Cord Connector: Detachable 20 amp IEC Monitor, Error Reporting, Auto Standby, Input
Common Mode Rejection (CMR) inlet. Cord locks with suppliled cord retention
(20 Hz to 1 kHz): 55 dB, typically >70 dB. Signal Compressor/Limiter, Peak Voltage
clip. Voltage range is indicated above IEC inlet. Limiter, Average Power Limiter, Clip Eliminator,
DC Output Offset (shorted input): < ± 3 mV. Reset Switch/Circuit Breaker: If the current Thermal Limiter, Limiter Tie, Load Supervision.
Input Impedance (nominal): draw of the amplifier exceeds safe limits, this
10 kilohms balanced, 5 kilohms unbalanced. breaker automatically disconnects the power Construction
Maximum Input Level: +20 dBu typical. supply from the AC mains. The switch resets Cooling: Dual-zone, microprocessor controlled,
the circuit breaker. continuously variable speed fans, front-to-back
Network: Onboard HiQnet™, compatible with
Output Connectors: Two high-current, 50A airflow.
standard 100 Mb Ethercom hardware.
Neutrik® Speakon® NL4MLP (mates with Front Panel: Cast aluminum with integrated
Load Impedance: (Note: Safe with all types of
NL4FC or NL4), one per channel. Ch 1 handles.
loads)
Speakon® is wired with Ch 1 and Ch 2 outputs Dimensions: 19 in. (48.3 cm) W x 3.5 in. (8.9
Stereo: 1/2/4/8/16 ohms.
for use with single 4-conductor cable. Two pairs cm) H x 16.2 in. (41.1 cm) D.
Bridge Mono: 2/4/8 ohms.
of high-current, 60A color-coded 5-way binding Weight: 28 lbs (12.7 kg) net, 36 lbs (16.3 kg)
Input Sensitivity (referenced to 8 ohm rated posts (for banana plugs, spade lugs or bare
output): 1.4V, 32 dB gain, and 26 dB gain. shipping.
wire).
Voltage Gain (referenced to 8 ohm rated Protection: Amplifier is protected against
Analog Input Connectors: A 3-pin female XLR reactive loads, faults and shorts. If one channel
output): connector for each channel.
MA-5000i: 37.1 dB to 22.2 dB experiences a catastrophic failure, the entire
Analog Loop Thru Connectors: Two male XLR amplifier will shut down.
MA-9000i: 37.9 dB to 23.0 dB
passive analog loop through. Included Accessories: Rear rack ears, rack
MA-12000i: 39.3 dB to 24.5 dB
Mode Switch/Indicator: Sets amplifier to screws, operation manual, power cords, foam
Required AC Mains: Universal AC input, 100-
Stereo, Bridge, or Input Y mode. OFF=Stereo, air filter.
240VAC, 50/60 Hz (±10%). Maximum AC mains
YEL=Bridge, GRN=Y.
voltage 264VAC. Regulatory Certifications
Network Connectors: Two Neutrik® Ethercon
AC Line Connector: Five cordsets supplied with
connector accepts RJ-45 type connectors for
amplifier (USA, UK, European, Australia, India).
HiQnet™ networking. Next to each connector is
Front Panel Controls and Indicators a yellow LINK ACT indicator that shows network
Bridge Mode Indicator: Amber LED illuminates activity, and a green 100Mb indicator that shows
a 100Mb network connection. Other Applications
when the amplifier is set to Bridge-Mono mode.
Ready Indicator: Green LED, one per channel. Data Indicator: Yellow LED on back panel
On (bright): Ready. indicates network data activity. Data indicator
On (dim): Onset of compression. flashes only when the amplifier is polled for
Off: Thermal failure. data, or is polled to see whether it is online.
Signal Indicators: One green LED per channel.
Solid green: Input signal is above –40 dBu.
Bright green: Channel’s output signal has
reached the onset of audible clipping.
4/08 140535-2
T O U R I N G
T he Crown Macro-Tech i Series amplifiers continue the Macro-Tech legacy of unparalleled sonic accu-
racy and detail, putting sound quality above all else. Their patented, cutting-edge Class-I circuitry gets
more power out of an amplifier with less waste. Each model features a Global Power Supply designed
to deliver maximum power in any country. The i Series offers studio-quality analog signal processing
with built-in load, line voltage, input and output monitoring. Standard Ethernet networking via System
Architect provides integrated monitoring and control to give system operators access to the system from
any location.
RECORDING &
BROADCAST
D Series
AMPLIFIERS RECORDING & BROADCAST
D Series: Long-Term Favorites
D-45, D-75A
POWER OUTPUT*
4-ohm Dual 8-ohm Dual 16-ohm Dual 8-ohm 16-ohm
Models (per channel) (per channel) (per channel) Bridge Bridge
8/06 136711-1C
T he D-45 and D-75A are long-term standards. They are perfect for moderate power applications
such as recording or broadcast studio near-field monitoring, video suite audio monitoring, a
recording/broadcast headphone amp or a small paging system. Convection cooled, the highly reli-
able D Series is protected against shorted, open, mismatched or low-impedance loads.
CINEMA
DSi Series
One-Touch
Performance
`` FEATURES
• Intuitive front-panel LCD screen, automatic presets for popular JBL cinema
speaker systems for quick, easy configuration.
• Onboard digital signal processing includes crossovers, EQ filters, delay, and
output limiting.
• Computer connectivity via USB allows fast setup and configuration with
HiQnet™ System Architect® software.
• Rear-panel HD-15 connector provides easy input/output connectivity
between DSi amplifiers and new DSi-8M System Monitor.
• Barrier strip outputs, removable Phoenix-style input.
• All models are THX®-approved.
POWER OUTPUT
2-ohm Dual 4-ohm Dual 8-ohm Dual 4-ohm 8-ohm
Models (per channel) (per channel) (per channel) Bridge Bridge
C I N E M A
T he Crown® DSi Series of power amplifiers provides onboard digital signal processing
including crossovers, EQ filters, delay and output limiting. A rear panel HD-15 connec-
tor provides easy input/output connectivity between DSi amplifiers and the new DSi-8M
System Monitor. The intuitive front panel LCD screen guides installers through a setup pro-
cess—featuring presets for the industry-standard JBL cinema loudspeaker systems—to make
configuration quick and easy. At the touch of a button, Crown’s DSi cinema amplifiers deliver
perfectly matched performance with each award-winning JBL ScreenArray® system, making
this the ultimate cinema solution.
AMPLIFIERS CINEMA
DSi-8M: Convenient Monitoring
DSi-8M
Performance
Monitor
`` FEATURES
• Compact 2-rack unit.
• 8 channels for monitoring processor or amplifier inputs.
• All inputs and outputs are balanced to interface with new cinema processors.
• No level jumps when switching between processor and amplifiers.
• 25-pin D-sub connectors, plus removable terminal blocks and HD-15 for
quick, hassle-free connections.
• Designed to work with bi-amplified sound systems to monitor the high- and
low-frequency outputs from the left, center and right channels.
`` SPECIFICATIONS
Performance
Rear Panel Controls and Connectors HD-15 Connector 4: Connects to Sw ampli-
Input Impedance (processor inputs): 10 kilohms.
IEC AC Power Receptacle: Connects to an fier.
Input Impedance (Processor Inputs): 10 k
IEC AC power cord. HD-15 Connector 5: Connects to Ll/Lh
ohms.
Input Connector 1: 10-pin Phoenix terminal amplifier.
Input Impedance (Power Amplifiers Inputs): block connects to the power amplifier speaker
> 50 k ohms. HD-15 Connector 6: Connects to Cl/Ch
outputs for the Left Surround, Right Sur- amplifier.
Power Requirements: 100-240V , 50-60 round, Back Surround Left, Back Surround
Hz, 32 watts. Right and Subwoofer channels. This connec- Optional Input Connector: 25-pin D-sub
tor lets you monitor the output of amplifiers connector connects to the EX output of the
Front Panel Controls and Indicators that do not include HD-15 connector options. processor.
Channel Select Buttons and LEDs: Eight Input Connector 2: 10-pin Phoenix terminal Bargraph Level: Trimpot adjusts the sensitiv-
pushbutton switches, one for each input block connects to the power amplifier speaker ity of the front-panel VU Bargraph Meter.
channel. Pressing a button monitors the output for the Left High, Left Low, Center
signal from that channel, and lights the cor- Main Input Connector: 25-pin D-sub con-
High, Center Low, Right High and Right Low nector connects to the main outputs of the
responding LED. Any combination of eight channels. This connector lets you monitor the
channels can be selected. processor.
output of amplifiers that do not include HD-15
Volume Control: Rotary potentiometer with connector options. “EX” Selector Switch: 8-position DIP switch.
knob controls the volume of the internal or Turn on switches 1-4 if system is without EX.
Amplifier Level Control: Trimpot adjusts
external speaker. Has no effect on the VU Turn on switches 5-8 if system is with EX.
the level of the input signals from the power
Bargraph Meter display. This routes the correct Ls/Rs inputs to the
amplifiers.
DSi-8M circuitry.
Processor/Amplifier Selector Switch and Processor Level: Trimpot adjusts the level of
LEDs: Pushbutton switch with corresponding the input signals from the processor. Construction
LEDs selects inputs from cinema procesor or Outputs to Power Amplifier Inputs: The six Chassis: Steel.
power amplfiers for monitoring. HD-15 connectors in this section connect Dimensions: EIA Standard 19-inch rack
VU Bargraph Meter: 12-segment meter to DSi amplifiers for both input and output mount width (EIA RS-310-B), 3.5 inches (8.9
displays input level of selected channels from signals. The HD-15 connectors have two cm) high and 9.625 inches (24.4 cm) deep
–40 VU to +3 VU. May be calibrated by the functions: behind front mounting surface.
rear-panel trim adjustment. Operates inde- 1. Connect DSi 8M outputs to DSi amplifier Net Weight:
pendently of the Volume Control. inputs. 10 lb 2 oz (4.63 kg).
Test Jack: 1/4" phone jack lets the user moni- 2. Connect DSi amplifier outputs to DSi 8M Shipping Weight:
tor the audio output of the DSi-8M. Insert- inputs for monitoring. 16 lb (7.26 kg).
ing a mono or stereo 1/4" phone plug here
disables the internal speaker and routes the Using VGA cables, the HD-15 connectors can
audio output to the Test Jack. be connected to Crown DSi power amplifier Regulatory Certifications
HD-15 connectors as described below.
Internal Speaker: For convenenient monitor-
ing at the monitor panel. HD-15 Connector 1: For cinema I/O compat-
ibility. Connects to Ls/Rs amplifier.
Power Switch and Power LED: Rocker switch
turns power on or off. LED illuminates when HD-15 Connector 2: Connects to Bsl/Bsr
power is on. amplifier.
HD-15 Connector 3: Connects to Rl/Rh
amplifier.
5/07 139623-2
C I N E M A
T he Crown® DSi-8M is a projection booth monitor designed to work with bi-amplified cinema
systems using the Crown DSi Series amplifiers. All controls necessary for daily operation of
the DSi-8M are easily accessible on the front panel. 8-channel monitoring allows you to moni-
tor either the processor or the power amplifier’s outputs: L, C, R, Ls, Rs, Bsl, Bsr, and Sub in
any combination. Input levels from the processor and power amplifier can be adjusted indepen-
dently. There are no huge level jumps when switching between processor and power amplifiers.
The bargraph display can be calibrated to the reference level for your theater. The projectionist
can see auditorium levels instantly.
AMPLIFIERS CINEMA
Other Cinema Products
CTs 2-Channel
`` FEATURES
• High power density. All two channel models in a
2U chassis.
• New Crown Switching Power Supply for lighter
weight.
• Selectable “Constant-Voltage” or low-impedance
operation per channel.
• 100V direct outputs on all models.
• Fully PIP2™-compatible.
POWER OUTPUT*
2-ohm Dual 4-ohm Dual 70V Dual 4-ohm
Models (per channel) (per channel) (per channel) Bridge
C rown Cinema Systems employ quality Crown professional amplifiers along with optional amplifier
accessories for the best in cinema sound. Crown’s Digital B-Chain system, which provides the first all-
digital cinema solution, employs Crown’s CTs Series amplifiers, IQ Networking amplifier modules,
and Crown’s DBC® Network Bridge for the first all-digital cinema solution.
AMPLIFIERS CINEMA
Other Cinema Products
CTs Multi-Channel
`` FEATURES
• High power density: Four-channel model in a 2U
chassis, eight-channel model in a 3U chassis.
• New Crown Switching Power Supply for lighter
weight.
• Selectable “Constant-Voltage” or low-impedance (4/8
ohm) operation per channel-pair.
• 100V direct outputs.
• New “FIT” (Fault Isolation Topology) circuitry isolates
fault conditions without affecting neighboring
channels.
• Accept VCA-MC accessory modules.
POWER OUTPUT*
All channels driven All channel pairs driven
Models 4-ohm Dual 8-ohm Dual 70V Dual 8-ohm Bridge
C I N E M A
Note: For more information about the products featured in this section, please refer to the following Crown
sections: CTs 2-Channel, CTs Multi-Channel, XLS Series.
NETWORKED PRODUCTS
& ACCESSORIES
PIPs
Accessories
NETWORKED PRODUCTS PIPS
TCP / IQ
PIP LITE
SmartAmp Automation for Networked Audio
PIP USP3/CN
SmartAmp Automation for TCP/IQ
NETWORKED PRODUCTS
ACCESSORIES & APPLICATIONS ACCESSORIES
Accessories
tiometer that provides remote volume control module already factory-installed, or your choice of
for one or more CTs amplifier channels. The MC modules can be easily added to the amplifier
potentiometer on the panel is wired directly by any authorized Crown Service Center.
to the VCA connectors on the VCA-MC.
4-VCAP: This is a 2-gang panel with four poten- Choosing the Right Module
tiometers that provide remote volume control To order accessory modules for your amplifier, please
for four or more CTs amplifier channels. The refer to the model tag (located on the back panel of the
potentiometers on the panel are wired directly amplifier) for your amplifier’s specific model number. TP-170V Constant-Voltage
to the VCA connectors on the VCA-MC. Then refer to the information below to select the correct Transformer Panel
accessory for your requirements. The Crown® TP-170V is a rack-mountable panel
CTs4200: VCA-MC4 or IQ-MC4 with four autoformers to provide impedance match-
CTs 4200A: VCA-MC4A or IQ-MC4A ing between amplifier outputs and “constant volt-
CTs 8200 or CTs 8200A: VCA-MC8 or IQ-MC8 age” loudspeakers. This unit allows amplifiers with-
out direct 70V or 100V output capability to drive
Regulatory Certifications distributed speaker systems designed to operate
For all CTs Multi-Channel Amp Accessories: at those voltages. The TP-170V is constructed of
sturdy steel, and hinged on one side to allow easy
access to the inside connections.
ACCESSORIES & APPLICATIONS ACCESSORIES
Accessories
cya
(cover your amp)
P.I.P.-CLP
The P.I.P.-C.L.P. is designed to detect and prevent overload. The same error 3PLUS3 3+3 Extended Warranty
detecting circuit that is used to signal the IOC indicator is used to activate this Crown’s No-Fault, 3+3 Extended Warranty pack-
error-driven compressor. It is not a typical signal-driven compressor but a age extends the terms of your original full war-
circuit to prevent an overload. It can yield up to 13 dB of additional signal safety ranty for an additional three years, thus covering
margin without noticeable program change. years four through six. Available for Crown
amplifiers only.
ACCESSORIES
PRODUCT
APPLICATIONS
& WARRANTY
Installed Sound Product Applications
SUMMARY OF WARRANTY
Crown International, 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A. warrants to you, the ORIGINAL PURCHASER and ANY SUBSEQUENT OWNER
of each NEW Crown product, for a period of three (3) years from the date of purchase by the original purchaser (the “warranty period”) that the new Crown product
is free of defects in materials and workmanship. We further warrant the new Crown product regardless of the reason for failure, except as excluded in this Warranty
Warranty is only valid within the country in which the product is purchased.
WARRANTY ALTERATIONS
No person has the authority to enlarge, amend, or modify this Crown Warranty. This Crown Warranty is not extended by the length of time which you are
deprived of the use of the new Crown product. Repairs and replacement parts provided under the terms of this Crown Warranty shall carry only the unex-
pired portion of this Crown Warranty.
DESIGN CHANGES
We reserve the right to change the design of any product from time to time without notice and with no obligation to make corresponding changes in prod-
ucts previously manufactured.
SUMMARY OF WARRANTY
Crown International, 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A. warrants to you, the ORIGINAL PURCHASER and ANY SUBSEQUENT OWNER
of each NEW Crown product, for a period of three (3) years from the date of purchase by the original purchaser (the “warranty period”) that the new Crown prod-
uct is free of defects in materials and workmanship, and we further warrant the new Crown product regardless of the reason for failure, except as excluded in this
Warranty.
Warranty is only valid within the country in which the product is purchased.
1 Note: If your unit bears the name “Amcron,” please substitute it for the name “Crown” in this warranty.
WARRANTY ALTERATIONS
No person has the authority to enlarge, amend, or modify this Crown Warranty. This Crown Warranty is not extended by the length of time which you are
deprived of the use of the new Crown product. Repairs and replacement parts provided under the terms of this Crown Warranty shall carry only the unex-
pired portion of this Crown Warranty.
DESIGN CHANGES
We reserve the right to change the design of any product from time to time without notice and with no obligation to make corresponding changes in prod-
ucts previously manufactured.
TRADEMARKS NOTICE: Crown, Crown Audio, Amcron, BCA, IQ, Differoid, DBC, IOC, IQ System, Macro-Tech, ODEP, P.I.P., and VZ are registered trademarks; Digital
B-Chain, Grounded Bridge, Power-Tech, PIP, PIP2, TCP/IQ, IQwic, SmartAmp, IQ2 and XTi are trademarks of Crown International.
Neutrik, Speakon, Windows, Dolby, DTS, HiQnet, CobraNet, ScreenArray, dbx, System Architect, Phoenix and JBL are used for information only and are the property of
their respective companies.
Crown Audio, Inc. reserves the right to make changes in specifications, software, or products without prior notice. Crown Audio, Inc. also assumes no responsibil-
ity for any error in type or print reproduction of the features or specifications in this literature. The information provided in this manual was deemed accurate as of
the publication date. However, updates to this information may have occurred. To obtain the latest version of this manual, please visit the Crown website at www.
crownaudio.com.
Some models may be exported under the name Amcron.