Masterpact Mtz1: Iec Circuit Breakers and Switch-Disconnectors From 630 To 1600 A User Guide
Masterpact Mtz1: Iec Circuit Breakers and Switch-Disconnectors From 630 To 1600 A User Guide
DOCA0100EN-02 12/2019
MasterPact MTZ1
IEC Circuit Breakers and Switch-Disconnectors
from 630 to 1600 A
User Guide
12/2019
DOCA0100EN-02
www.schneider-electric.com
The information provided in this documentation contains general descriptions and/or technical character-
istics of the performance of the products contained herein. This documentation is not intended as a
substitute for and is not to be used for determining suitability or reliability of these products for specific user
applications. It is the duty of any such user or integrator to perform the appropriate and complete risk
analysis, evaluation and testing of the products with respect to the relevant specific application or use
thereof. Neither Schneider Electric nor any of its affiliates or subsidiaries shall be responsible or liable for
misuse of the information contained herein. If you have any suggestions for improvements or amendments
or have found errors in this publication, please notify us.
You agree not to reproduce, other than for your own personal, noncommercial use, all or part of this
document on any medium whatsoever without permission of Schneider Electric, given in writing. You also
agree not to establish any hypertext links to this document or its content. Schneider Electric does not grant
any right or license for the personal and noncommercial use of the document or its content, except for a
non-exclusive license to consult it on an "as is" basis, at your own risk. All other rights are reserved.
All pertinent state, regional, and local safety regulations must be observed when installing and using this
product. For reasons of safety and to help ensure compliance with documented system data, only the
manufacturer should perform repairs to components.
When devices are used for applications with technical safety requirements, the relevant instructions must
be followed.
Failure to use Schneider Electric software or approved software with our hardware products may result in
injury, harm, or improper operating results.
Failure to observe this information can result in injury or equipment damage.
© 2019 Schneider Electric. All rights reserved.
2 DOCA0100EN-02 12/2019
Table of Contents
Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 1 MasterPact MTZ1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
MasterPact MTZ1 Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Fixed Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Drawout Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Device Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
MicroLogic X Control Unit: Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Go2SE Landing Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Chapter 2 MasterPact MTZ1 Normal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.1 Device Operating Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Operating the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Control Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Opening the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Closing the Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Resetting the Circuit Breaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Engaging the ERMS Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Operating Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
2.2 Drawout Device Racking Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Drawout MasterPact MTZ1 Device Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Disconnecting the Drawout Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Connecting the Drawout Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Removing the Drawout Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Installing the Drawout Device in the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
2.3 Device Locking Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Locking the Pushbuttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Locking the Device in Open Position with Padlocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Locking the Device in Open Position with Keylocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Chassis Locking in Disconnected Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Chassis Locking in Any Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Locking the Safety Shutters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
2.4 Device Interlocking Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Mismatch Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
VPEC Door Interlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
VPOC Open-door Racking Interlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
IPA Cable-type Door Interlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Mechanical Interlocking for Transfer Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Chapter 3 MasterPact MTZ Critical Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Finding the Cause of a Trip or an Alarm in Critical Cases. . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Resetting the Circuit Breaker After a Trip Due to an Electrical Fault . . . . . . . . . . . . . . . . . . 106
Resetting the Circuit Breaker After a Trip Due to an Incident Detected by the MicroLogic X
Self-tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Diagnosing Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Diagnosing Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
DOCA0100EN-02 12/2019 3
Chapter 4 MasterPact MTZ Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Introduction to Commissioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Inspection and MicroLogic X Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Communication Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Final Checks and Reporting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
MasterPact MTZ Test Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Chapter 5 MasterPact MTZ Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Introduction to Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Troubleshooting: Chassis Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Troubleshooting: Unexpected Tripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Troubleshooting: Mechanical Control Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Troubleshooting: Electrical Control Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Troubleshooting: Control Operations from EcoStruxure Power Device App . . . . . . . . . . . . . 143
Troubleshooting: Control Operations from IO Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Troubleshooting: Control Operations from EcoStruxure Power Commission Software . . . . . 146
Troubleshooting: Control Operations from IFE/EIFE Webpages . . . . . . . . . . . . . . . . . . . . . . 148
Troubleshooting: Control Operations from Communication Network. . . . . . . . . . . . . . . . . . . 150
Troubleshooting: Control Operations from FDM128 Display . . . . . . . . . . . . . . . . . . . . . . . . . 152
Chapter 6 Schneider Electric Green Premium™ Ecolabel . . . . . . . . . . . . . . . . . . . . . . 153
Schneider Electric Green Premium™ Ecolabel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
4 DOCA0100EN-02 12/2019
Safety Information
Important Information
NOTICE
Read these instructions carefully, and look at the equipment to become familiar with the device before
trying to install, operate, service, or maintain it. The following special messages may appear throughout
this documentation or on the equipment to warn of potential hazards or to call attention to information that
clarifies or simplifies a procedure.
PLEASE NOTE
Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this
material.
A qualified person is one who has skills and knowledge related to the construction and operation of
electrical equipment and its installation, and has received safety training to recognize and avoid the
hazards involved.
DOCA0100EN-02 12/2019 5
SAFETY NOTICE
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See
NFPA 70E, CSA Z462, NOM 029-STPS or local equivalent.
This equipment must only be installed and serviced by qualified electrical personnel.
Turn off all power supplying this equipment before working on or inside this equipment.
Always use a properly rated voltage sensing device to confirm power is off.
Replace all devices, doors, and covers before turning on power to this equipment.
Beware of potential hazards, and carefully inspect the work area for tools and objects that may have
been left inside the equipment.
Failure to follow these instructions will result in death or serious injury.
WARNING
POTENTIAL COMPROMISE OF SYSTEM AVAILABILITY, INTEGRITY, AND CONFIDENTIALITY
Change default passwords at first use to help prevent unauthorized access to device settings,
controls, and information.
Disable unused ports/services and default accounts to help minimize pathways for malicious
attackers.
Place networked devices behind multiple layers of cyber defenses (such as firewalls, network
segmentation, and network intrusion detection and protection).
Use cybersecurity best practices (for example, least privilege, separation of duties) to help prevent
unauthorized exposure, loss, modification of data and logs, or interruption of services.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
6 DOCA0100EN-02 12/2019
About the Book
At a Glance
Document Scope
The aim of this guide is to provide users, installers, and maintenance personnel with technical information
needed to operate MasterPact™ MTZ1 circuit breakers and switch-disconnectors, in compliance with the
IEC standards.
Validity Note
This guide applies to MasterPact MTZ1 circuit breakers and switch-disconnectors.
This guide applies to MicroLogic™ X control units:
With firmware version 004.000.000 or greater
With hardware version 001.000.000 or greater
Online Information
The information contained in this document is likely to be updated at any time. Schneider Electric strongly
recommends that you have the most recent and up-to-date version available on www.schneider-
electric.com/docs.
The technical characteristics of the devices described in the present document also appear online. To
access the information online:
Step Action
1 Go to the Schneider Electric home page www.schneider-electric.com.
2 In the Search box type the reference of a product or the name of a product range.
Do not include blank spaces in the reference or product range.
To get information on grouping similar modules, use asterisks (*).
3 If you entered a reference, go to the Product Datasheets search results and click on the
reference that interests you.
If you entered the name of a product range, go to the Product Ranges search results and click
on the product range that interests you.
4 If more than one reference appears in the Products search results, click on the reference that
interests you.
5 Depending on the size of your screen, you may need to scroll down to see the datasheet.
6 To save or print a datasheet as a .pdf file, click Download XXX product datasheet.
The characteristics that are described in the present document should be the same as those character-
istics that appear online. In line with our policy of constant improvement, we may revise content over time
to improve clarity and accuracy. If you see a difference between the document and online information, use
the online information as your reference.
DOCA0100EN-02 12/2019 7
Related Documents
You can download these technical publications and other technical information from our website at
https://www.se.com/ww/en/download/ .
Trademark Notice
All trademarks are owned by Schneider Electric Industries SAS or its affiliated companies.
8 DOCA0100EN-02 12/2019
MasterPact MTZ1
MasterPact MTZ1 Description
DOCA0100EN-02 12/2019
Chapter 1
MasterPact MTZ1 Description
DOCA0100EN-02 12/2019 9
MasterPact MTZ1 Description
Description
The MasterPact MTZ1 range of circuit breakers and switch-disconnectors offers current ratings from 630 A
to 1600 A, for AC power systems up to 690 Vac. The range is covered by one frame size.
MasterPact MTZ1 devices are available in the following power systems:
3-pole (3P)
4-pole (4P)
Convention
In this guide, the term MasterPact MTZ device covers circuit breakers and switch-disconnectors.
Circuit Breakers
The following performance levels (Icu at 415 Vac) are available:
H1: standard short-circuit level (42 kA) with total selectivity
H2: high short-circuit level (50 kA) with high selectivity (42 kA)
H3: very high short-circuit level (66 kA) with very high selectivity (50 kA)
L1: extremely high short-circuit level (150 kA) with strong current limitation and selectivity (10 kA)
NOTE: The values above correspond to a 415 Vac network, for higher voltage levels the values can be
different. Refer to LVPED216026EN MasterPact MTZ Catalogue.
NOTE: The arc chutes on the MasterPact MTZ1 H3 are built-in and cannot be removed.
Switch-Disconnectors
The switch-disconnector functions in the HA performance level (Icw = 36 kA/1s).
For information about available switch-disconnector models, refer to LVPED216026EN MasterPact MTZ
Catalogue.
10 DOCA0100EN-02 12/2019
MasterPact MTZ1 Description
Fixed Device
DOCA0100EN-02 12/2019 11
MasterPact MTZ1 Description
The following images zoom in on the accessories for the fixed device:
F Standard SDE1 fault-trip indication contact K MN undervoltage release or MX2 opening voltage release
G Optional SDE2 fault-trip indication contact or RES electrical L XF closing voltage release
remote reset M MX1 opening voltage release
H Microswitch N PF ready-to-close contact
I M2C programmable contacts or ESM ERMS switch module O VSPO OFF-position locking by keylocks (incompatible with BPFE
J Isolation module pushbutton)
P VCPO OFF-position locking by padlocks
Q BPFE electrical closing pushbutton
12 DOCA0100EN-02 12/2019
MasterPact MTZ1 Description
DOCA0100EN-02 12/2019 13
MasterPact MTZ1 Description
Drawout Device
Definition
A drawout device is composed of the moving part (also called the device) and the fixed part (or chassis).
A Carrying grip
B Arc chute
C Blue fault-trip reset button
D Opening pushbutton
E Closing pushbutton
F Disconnectable contact block cover
G Front cover
H Spring charging handle
I VBP pushbutton locking cover (optional)
J Rating plate
K Spring charged and ready-to-close indicator
L Main-contact position indicator
M Window to consult the (optional) CDM mechanical
operation counter
N Control unit
O Control unit transparent cover
14 DOCA0100EN-02 12/2019
MasterPact MTZ1 Description
The following images zoom in on the accessories for the moving part of a drawout device.
F Standard SDE1 fault-trip indication contact K MN undervoltage release or MX2 opening voltage release
G Optional SDE2 fault-trip indication contact or RES electrical L XF closing voltage release
remote reset M MX1 opening voltage release
H Microswitch N PF ready-to-close contact
I M2C programmable contacts or ESM ERMS switch module O VSPO OFF-position locking by keylocks (incompatible with BPFE
J Isolation module pushbutton)
P VCPO OFF-position locking by padlocks
Q BPFE electrical closing pushbutton
DOCA0100EN-02 12/2019 15
MasterPact MTZ1 Description
Chassis Description
The following image shows the standard version of the chassis (no optional accessories).
16 DOCA0100EN-02 12/2019
MasterPact MTZ1 Description
DOCA0100EN-02 12/2019 17
MasterPact MTZ1 Description
18 DOCA0100EN-02 12/2019
MasterPact MTZ1 Description
DOCA0100EN-02 12/2019 19
MasterPact MTZ1 Description
Device Identification
Identification
The MasterPact MTZ1 device can be identified in the following ways:
Rating plate on device
QR code located:
On the front face of the control unit of the circuit breaker
On the front face of the switch-disconnector
20 DOCA0100EN-02 12/2019
MasterPact MTZ1 Description
The accessory voltages label gives the voltage of the accessories which are installed in the device and
which need to be connected to a power supply.
DOCA0100EN-02 12/2019 21
MasterPact MTZ1 Description
Rating Plate
The rating plate with the device information is located on the front cover of the device.
A Device size and rated current x 100 A J Uimp: rated impulse withstand voltage
B Ui: rated insulation voltage K Icu: rated ultimate short-circuit breaking capacity
C Ue: rated operational voltage L Selectivity category as per IEC 60947-2
D Frequency M Place for sticker with IP address of the optional EIFE
E Type of device: circuit breaker or switch-disconnector, interface
suitable for insulation N Icm: rated short-circuit making capacity
F Ics: rated service short-circuit breaking capacity O Ith: conventional free air thermal current
G Icw: rated short-time withstand current P Ie: rated operational current
H Standards
I Performance level
QR Code
When the QR code on the front face of a MasterPact MTZ device is scanned with a smartphone running a
QR code reader and connected to the Internet, the Go2SE landing page is displayed (see page 26). The
landing page displays some information about the device and a list of menus.
22 DOCA0100EN-02 12/2019
MasterPact MTZ1 Description
Introduction
The MicroLogic X control unit includes:
LEDs to monitor the status of the circuit breaker
A local Human Machine Interface comprising a graphic display with colored backlight, contextual
buttons, and dedicated buttons
LEDs to monitor the cause of trips and alarms
A Ready LED
B Service LED
C ERMS LED
D Graphic display screen
E NFC wireless communication zone
F Home button
G Three contextual buttons
H Escape button ESC
I Bluetooth LED
J Bluetooth activation button
K Test button for ground-fault and earth-leakage
protection (MicroLogic 6.0 X and 7.0 X)
L Test/Reset button for trip cause LEDs and alarms
M Mini USB port under rubber cover
N Overload and trip cause LEDs
O Cover for internal battery
P VPS voltage power supply module (optional)
Q VPS LED to indicate that the VPS module is
supplying the control unit
R QR code to access product information
S Control unit identification number
T Control unit type
U Sensor plug with the rated current of the circuit
breaker
V Plastic cover
Status LEDs
LED Description
Ready The Ready LED blinks slowly when the standard protection functions of the control unit are
operational.
The service LED alerts the user to the health state of the circuit breaker.
Orange LED: medium severity detected alarm that requires non-urgent maintenance action.
Red LED: high severity detected alarm that requires immediate maintenance action.
ERMS The ERMS (Energy Reduction Maintenance Setting) LED has the following statuses:
Blue LED: ERMS engaged
Off LED: ERMS disengaged
DOCA0100EN-02 12/2019 23
MasterPact MTZ1 Description
Test Button
The test button is used to test the ground-fault protection for MicroLogic 6.0 X and the earth-leakage
protection for MicroLogic 7.0 X.
LEDs Description
MicroLogic 2.0 X, 5.0 X, 6.0 X, 7.0 X: Overload pre-alarm, the load exceeds 90%
and is lower than 105% of the Ir setting of the long-time protection.
MicroLogic 2.0 X, 5.0 X, 6.0 X, 7.0 X: Overload alarm, the load exceeds 105% of
the Ir setting of the long-time protection.
MicroLogic 2.0 X, 5.0 X, 6.0 X, 7.0 X: MicroLogic control unit invalid result detected
during self test.
NOTE: If the MicroLogic X control unit is not powered, the trip cause LEDs go off after 4 hours. After this
period, press the Test/Reset button to light them again.
24 DOCA0100EN-02 12/2019
MasterPact MTZ1 Description
Test/Reset Button
The Test/Reset button performs the following functions:
Test of the internal battery or check LED functionality: press and hold the Test/Reset button for less than
3 seconds, the four trip cause LEDs switch off for one second. One of the following results:
The four trip cause LEDs switch on for two seconds: the battery is OK.
The four trip cause LEDs flash sequentially for two seconds: the battery is near the end of its life.
Replace the battery.
The four trip cause LEDs do not light: replace the battery.
NOTE: This test must be carried out immediately after the replacement of the internal battery to check
the correct functioning of the new battery. It can then be carried out at any time in the life of the internal
battery.
Reset of the latched events: press and hold the Test/Reset button for more than 3 seconds to reset the
latched events. The trip cause LEDs and the service LED switch off.
NOTE: The MicroLogic X control unit does not support USB keys. Even if a USB key is connected using
an adapter, data is not transferred.
QR Code
When the QR code on the front face of a MicroLogic X control unit is scanned with a smartphone running
a QR code reader and connected to the Internet, the Go2SE landing page is displayed (see page 26). The
landing page displays some information about the device and a list of menus.
Use the identification number to register your MicroLogic X control unit through mySchneider app, the
customer care mobile application.
Registering your MicroLogic X control unit enables you to keep your records up to date and enables
traceability.
Internal Battery
The internal battery powers the trip cause LEDs and the main diagnostic functions in the absence of any
other power supply.
Sensor Plug
The protection ranges depend on the rated current In, defined by the sensor plug present below the
MicroLogic X control unit.
DOCA0100EN-02 12/2019 25
MasterPact MTZ1 Description
Presentation
When the QR code on the front face of a MasterPact MTZ device is scanned with a smartphone running a
QR code reader and connected to the Internet, the Go2SE landing page is displayed.
The landing page displays information about the device and a list of menus.
Characteristics
Selecting this menu gives access to a product datasheet with detailed information about the MicroLogic X
control unit.
Documentation
Selecting this menu gives access to a sub-menu with the following options:
Asset Life Cycle Documents: gives access to Safe Repository.
Safe Repository is a web service allowing documentation linked to assets to be consulted, stored, and
shared in a Schneider Electric environment. Access to Safe Repository is restricted to authorized users.
Safe Repository gives access to the bill of materials of the MasterPact MTZ circuit breaker.
Technical Guidance at Glance: gives access to the MasterPact MTZ technical publications, including:
MasterPact MTZ - MicroLogic X Control Unit - User Guide
MasterPact MTZ1 - Circuit Breakers and Switch-Disconnectors - User Guide
MasterPact MTZ2/MTZ3 - Circuit Breakers and Switch-Disconnectors - User Guide
All the instruction sheets for MasterPact MTZ devices and MicroLogic X control units
Product Documentation: gives access to the MicroLogic X technical publications
26 DOCA0100EN-02 12/2019
MasterPact MTZ1 Description
EcoStruxure Facility Expert enables managers and maintenance personnel to access the maintenance
plan for MasterPact MTZ devices.
EcoStruxure Facility Expert helps maintenance personnel to diagnose issues remotely and manage
maintenance efficiently by:
Providing relevant information on critical assets.
Sending immediate state of the equipment and detailed information helping for diagnostics.
mySchneider App
Selecting this application gives access to the Schneider Electric customer care mobile application
mySchneider app that can be downloaded on Android and iOS smartphones. For smartphone
compatibility, check on your application store. The customer care application offers self-service
instructions and easy access to expert support and information.
DOCA0100EN-02 12/2019 27
MasterPact MTZ1 Description
Operating Conditions
Introduction
MasterPact MTZ devices are designed and tested for operation in industrial atmospheres. It is
recommended that equipment is cooled or heated to the proper operating temperature and kept free of
excessive vibration and dust.
Ambient Temperature
MasterPact MTZ devices can operate under the following temperature conditions:
Electrical and mechanical characteristics specified for an ambient temperature of -25 °C to +70 °C .
Circuit-breaker closing specified down to -35 °C by manual operation with closing pushbutton.
Standard Title
IEC 60068-2-1 Dry cold, at -40 °C
IEC 60068-2-2 Dry heat, at +85 °C
IEC 60068-2-30 Damp heat (temperature +55 °C, relative humidity 95%)
IEC 60068-2-52 level 2 Salt mist
Industrial Environments
MasterPact MTZ devices can operate in the industrial environments defined by IEC 60947 (pollution
degree up to 3).
It is advisable to check that devices are installed in suitably cooled switchboards without excessive dust.
Conditions Standard
Corrosive industrial atmospheres Category 3C3 compliant with IEC 60721-3-3
Sea salts 0.8 to 8 mg/m² day average over the year Compliant with IEC 60721-2-5
Mechanically active substances Category 3S3 compliant with IEC 60721-3-3
Beyond these conditions, MasterPact MTZ devices must be installed inside switchboards with an IP rating
equal to or greater than IP54.
Vibration
MasterPact MTZ devices have successfully passed tests for the following vibration levels, in compliance
with IEC 60068-2-6 and IEC 60068-2-27:
2 Hz to 13.2 Hz: amplitude +/- 1 mm.
13.2 Hz to 100 Hz: constant acceleration of 0.7 g.
Vibration testing to these levels is required by merchant marine inspection organizations (for example,
Veritas, Lloyd’s).
MasterPact MTZ devices have also been successfully tested according to:
Annex Q - IEC 60947-1: Special tests – damp heat, salt mist, vibration and shock
IEC 60947-1 - Category D: Environment subject to temperature, humidity and vibration
28 DOCA0100EN-02 12/2019
MasterPact MTZ1 Description
Altitude
MasterPact MTZ devices are designed and tested to operate at altitudes below 2,000 m.
At altitudes above 2,000 m, the characteristics of the ambient air (electrical resistance, cooling capacity)
lower product characteristics as follows:
Characteristics Altitude
2,000 m 3,000 m 4,000 m 5,000 m
Impulse withstand voltage Uimp (kV) 12 11 10 8
Rated insulation voltage (Ui) (V) 1,000 900 780 700
Maximum rated operational MasterPact MTZ1 except H3 690 690 630 560
voltage 50/60 Hz Ue (V)
MasterPact MTZ1 H3 440 440 440 440
Rated current (A) at 40 °C 1 x In 0.99 x In 0.96 x In 0.94 x In
Electromagnetic Disturbances
MasterPact MTZ devices have protection against:
Overvoltages caused by devices that generate electromagnetic disturbance.
Overvoltages caused by atmospheric disturbance or by a distribution-system outage (for example, a
lighting system failure).
Devices emitting radio waves (for example, radio transmitters, walkie-talkies, or radar).
Electrostatic discharge produced by users.
MasterPact MTZ devices have successfully passed the electromagnetic-compatibility tests (EMC) defined
by the following international standards:
IEC 60947-2, appendix F.
IEC 60947-2, appendix B (control units with earth-leakage function).
DOCA0100EN-02 12/2019 29
MasterPact MTZ1 Description
30 DOCA0100EN-02 12/2019
MasterPact MTZ1
MasterPact MTZ1 Normal Operation
DOCA0100EN-02 12/2019
Chapter 2
MasterPact MTZ1 Normal Operation
DOCA0100EN-02 12/2019 31
MasterPact MTZ1 Normal Operation
Section 2.1
Device Operating Actions
32 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Device Status
The indicators on the front of the device show the following information:
Reset button:
In: the device is closed or open voluntarily (not tripped)
Out: the device has tripped
A Reset button
B Position indicator of main contacts
C Closing spring and ready-to-close indicator
DOCA0100EN-02 12/2019 33
MasterPact MTZ1 Normal Operation
Anti-Pumping Function
MasterPact MTZ devices provide a mechanical anti-pumping function. In the event of simultaneous
maintained opening and closing orders, the standard mechanism blocks the main contacts in the open
position. After a trip due to an electrical fault or intentional opening using the manual or electrical controls,
the closing order must first be discontinued, then reactivated to close the circuit breaker. This prevents a
cycle of closing and opening.
When remote operation features are used, allow at least four seconds for the MCH gear motor to charge
the device closing spring completely before the XF closing voltage release is actuated.
To prevent the device from closing prematurely, the PF ready-to-close contact can be series connected
with the XF closing voltage release.
Automatic charge: If the optional MCH gear motor is installed, the spring is automatically charged after
closing.
34 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
DOCA0100EN-02 12/2019 35
MasterPact MTZ1 Normal Operation
36 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Control Modes
Presentation
The circuit breaker control mode is a MicroLogic X setting which defines the means to control the opening
and closing functions of the circuit breaker.
Two control modes are available: Manual and Auto.
Manual control mode only accepts orders made using one of the following:
The mechanical buttons on the front of the circuit breaker.
The external pushbutton connected to the MN/MX/XF voltage releases.
The BPFE electrical closing pushbutton.
Auto control mode has two settings: Local or Remote. All orders accepted in Manual control mode are
accepted in Auto control mode, as well as orders from local or remote communication as follows:
Auto Local: the operator needs to be close to the circuit breaker to establish communication and only
orders sent from a local source through communication are accepted:
EcoStruxure Power Commission software through USB connection
EcoStruxure Power Device app with MasterPact Operation Assistant Digital Module through
Bluetooth or USB OTG connection
Auto Remote: the operator does not need to be next to the circuit breaker to establish communication
and orders are accepted only when sent from a remote source through the communication network.
NOTE: EcoStruxure Power Commission software connected through the communication network can be
used to send control orders to the circuit breaker.
The control mode factory setting is Auto Remote.
NOTE: The switch-disconnector control mode corresponds to the Manual control mode of circuit breakers.
To operate a switch-disconnector through communication, it is possible to use an IO module. Refer to
DOCA0055EN Enerlin'X IO - Input/Output Application Module for One IEC Circuit Breaker - User Guide.
DOCA0100EN-02 12/2019 37
MasterPact MTZ1 Normal Operation
38 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
IO: with the Breaker Operation predefined application of the IO module set to local control mode
EcoStruxure Power Commission software: command sent through USB connection
EcoStruxure Power Device app with MasterPact Operation Assistant Digital Module:
Through Bluetooth low energy wireless communication
Through USB OTG connection
DOCA0100EN-02 12/2019 39
MasterPact MTZ1 Normal Operation
IO: with the Breaker Operation predefined application of the IO module set to remote control mode
Communication: remote command through IFE, EIFE, or IFM interface.
NOTE:
The Local or Remote mode cannot be set on the MicroLogic X display screen.
When Auto control mode is set, the control mode is Auto Local or Auto Remote, depending on the last
setting.
40 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Predefined Events
Changing the control mode settings generates the following events:
Recommended Actions
DOCA0100EN-02 12/2019 41
MasterPact MTZ1 Normal Operation
Opening Conditions
To open the device, the device must be closed (I).
NOTE: An opening order always takes priority over a closing order.
Automatic Manual, MN undervoltage release, The MN undervoltage release opens the device
Auto: with or without MN delay automatically in the case of voltage drop.
Local, or unit
Auto:
Remote
By external Manual, External pushbutton Press the external pushbutton which is connected to the MX
pushbutton Auto: wired by customer opening voltage release or to the MN undervoltage release
Local, or One of the following via the customer terminal block.
Auto: accessories: When the MN undervoltage release is connected to the MN
Remote MX standard or delay unit, the device opens with the corresponding time
communicating delay.
opening voltage
release
MN undervoltage
release, with or
without MN delay
unit
42 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
In addition, the circuit breaker can be opened in the following ways when Auto control mode is configured.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Do not operate the circuit breaker without confirming that doing so will not create a hazardous
situation.
Do not allow any person to work on the electrical network without physically validating the successful
execution of the local or remote software actions for opening the circuit breaker or switching off the
electrical circuit.
Failure to follow these instructions will result in death or serious injury.
DOCA0100EN-02 12/2019 43
MasterPact MTZ1 Normal Operation
Through Auto: MX communicating opening voltage Send a command to open the circuit
IFE/EIFE Remote release breaker from the IFE/EIFE control
webpages Isolation module webpage.
ULP port module This opening action is password-
IFE or EIFE interface, or IFE server protected.
Refer to the relevant document:
DOCA0084EN Enerlin'X IFE -
Ethernet Switchboard Server - User
Guide
DOCA0142EN Enerlin'X IFE -
Ethernet Interface for One IEC Circuit
Breaker - User Guide
DOCA0106EN Enerlin'X EIFE -
Embedded Ethernet Interface for One
MasterPact MTZ Drawout Circuit
Breaker - User Guide
If the device does not open, refer to the troubleshooting chapter (see page 136).
44 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Closing Conditions
To close the device, the following conditions must be met:
Device is open (O).
Closing spring is charged.
The device is ready to close, OK is displayed.
NOTE: An opening order always takes priority over a closing order. The device cannot be closed while an
opening order is being received. If OK is crossed-out on the ready-to-close indicator, an order to open is
being received (either electrically or mechanically) and must be ended before OK can be displayed.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Do not re-close the device on an electrical fault.
First inspect and, if necessary, repair the downstream equipment.
Failure to follow these instructions will result in death or serious injury.
DOCA0100EN-02 12/2019 45
MasterPact MTZ1 Normal Operation
In addition, the circuit breaker can be closed in the following ways when Auto control mode is configured.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Do not operate the circuit breaker without confirming that doing so will not create a hazardous
situation.
Do not allow any person to work on the electrical network without physically validating the successful
execution of the local or remote software actions for closing the circuit breaker or switching on the
electrical circuit.
Failure to follow these instructions will result in death or serious injury.
46 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
If the device does not close, refer to the troubleshooting chapter (see page 136).
NOTE: Using EcoStruxure Power Commission software, you can determine whether the closing inhibition
can be controlled using the IO module. For more information, refer to EcoStruxure Power Commission
Online Help.
WARNING
RESTRICTED CLOSING INHIBITION
Do not use the inhibit closing order to lock the circuit breaker in open position.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
The inhibit close order inhibits only the closing orders allowed in Auto control mode. The closing orders
issued from the mechanical closing pushbutton or BPFE, or from the pushbutton directly connected to the
XF voltage release are not inhibited.
DOCA0100EN-02 12/2019 47
MasterPact MTZ1 Normal Operation
Resetting Conditions
After a trip, the circuit breaker must be reset before closing it.
Resetting is possible in all control modes.
Automatic (RAR XF communicating or After a trip, RAR automatic reset allows the circuit breaker to be
automatic reset standard closing voltage closed without the blue fault-trip reset button being pushed in. The
option) release use of XF closing voltage release is compulsory with this option.
Isolation module The mechanical indicator and the SDE fault-trip indication contact
MCH gear motor remain in detected fault position.
To reset the SDE fault-trip indication contact and the mechanical
indicator, push in the blue fault-trip reset button.
Electrical with External pushbutton Press the external pushbutton which is connected to the RES
external wired by customer electrical remote reset via the customer terminal block.
pushbutton RES electrical remote The use of XF closing voltage release is compulsory with this option.
reset The RES electrical remote reset resets the SDE fault-trip indication
XF communicating or contact and the mechanical indicator, and allows the circuit breaker
standard closing voltage to be closed.
release NOTE: The RES electrical remote reset is not compatible with the
Isolation module SDE2 option.
MCH gear motor
48 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Presentation
Engage the ERMS function to reduce protection settings so that the circuit breaker trips as soon as
possible when an internal arc fault occurs. Minimizing the time between fault and trip helps to reduce the
risk of injury when qualified electrical personnel are near energized equipment.
Operating Principle
The ERMS function can be engaged with both the EcoStruxure Power Device app (password-protected)
and an external selector switch.
The ERMS function must be disengaged by the interface that engaged it:
If it is engaged on a smartphone, it must be disengaged by the same smartphone.
If it is engaged by the external ERMS switch connected to the ESM module, it must be disengaged by
the ERMS switch.
If it is engaged by both smartphone and ERMS switch, it must be disengaged by both smartphone and
ERMS switch.
For more information, refer to DOCA0102EN MasterPact MTZ - MicroLogic X Control Unit - User Guide.
DOCA0100EN-02 12/2019 49
MasterPact MTZ1 Normal Operation
NOTICE
HAZARD OF LOSS OF POWER
Ensure that the ERMS protection settings are properly configured prior to engagement.
Failure to follow these instructions can result in loss of service due to power loss.
The ERMS can be engaged in different ways, according to the circuit breaker configuration and its
accessories:
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Prior to disengaging ERMS:
Carefully inspect your work area, and remove any tools and objects left inside the equipment.
Ensure that all personnel are away from the equipment, and devices, doors, and covers are in place.
A digital lock function establishes a digital lock between a smartphone running the EcoStruxure Power
Device app and the MicroLogic X control unit when ERMS is engaged by the smartphone. The digital lock
function ensures that when the ERMS function is engaged by a smartphone, it must be disengaged by the
same smartphone.
The way to disengage the ERMS function depends on how it was engaged:
50 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Operating Accessories
For information on installation, consult the instruction sheet on the Schneider Electric website:
XF standard closing voltage release: NVE40749
XF communicating closing voltage release: NVE40766
For information on installation, consult the instruction sheet on the Schneider Electric website:
MX standard opening voltage release: NVE40749
MX communicating opening voltage release: NVE40766
DOCA0100EN-02 12/2019 51
MasterPact MTZ1 Normal Operation
For information on installation, consult the instruction sheet on the Schneider Electric website:
MN standard undervoltage release: NVE40749
MN undervoltage release with diagnostic function: NVE40766
For information on installation, consult the instruction sheet on the Schneider Electric website: NVE40748.
For information on installation, consult the instruction sheet on the Schneider Electric website: NVE40771.
52 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
PF Ready-to-close Contact
This is an optional accessory that is mounted inside the device.
The PF ready-to-close contact delivers remotely, the indication delivered locally by the ready-to-close
indicator.
It consists of a changeover contact indicating remotely that the circuit breaker is ready to close, that is:
The circuit breaker is in the open position.
The spring mechanism is charged.
There is no maintained opening order.
For information on installation, consult the instruction sheet on the Schneider Electric website: NVE35466.
For information on installation, consult the instruction sheet on the Schneider Electric website: NVE35514.
DOCA0100EN-02 12/2019 53
MasterPact MTZ1 Normal Operation
For installation of the ESM ERMS switch module, contact your Schneider Electric field service
representative.
For information on installation, consult the instruction sheet on the Schneider Electric website: NVE35516.
For information on installation, consult the instruction sheet on the Schneider Electric website:
ULP port module for fixed MasterPact MTZ1: NVE40791
ULP port module for drawout MasterPact MTZ1: NVE40796
54 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
It provides digital access to all the data delivered by the MicroLogic X control unit. In addition, it monitors
the position of the device in the chassis: connected, test, and disconnected.
For information on installation, consult the instruction sheet on the Schneider Electric website: NVE23550.
For information on usage, refer to DOCA0106EN Enerlin'X EIFE - Embedded Ethernet Interface for One
MasterPact MTZ Drawout Circuit Breaker - User Guide.
The circuit breaker is connected to the IFE interface through the ULP port module and a prefabricated ULP
cord.
For information on installation, consult the instruction sheet on the Schneider Electric website: HRB49218.
For information on usage, refer to DOCA0142EN Enerlin'X IFE - Ethernet Interface for One IEC Circuit
Breaker - User Guide.
For information on installation, consult the instruction sheet on the Schneider Electric website: HRB49218.
For information on usage, refer to DOCA0084EN Enerlin'X IFE - Ethernet Switchboard Server - User
Guide.
DOCA0100EN-02 12/2019 55
MasterPact MTZ1 Normal Operation
For information on installation, consult the instruction sheet on the Schneider Electric website: NVE85393.
For information on installation, consult the instruction sheet on the Schneider Electric website: HRB49217.
For information on usage, refer to DOCA0055EN Enerlin'X IO - Input/Output Application Module for One
IEC Circuit Breaker - User Guide.
56 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Section 2.2
Drawout Device Racking Actions
DOCA0100EN-02 12/2019 57
MasterPact MTZ1 Normal Operation
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See
NFPA 70E or CSA Z462 or local equivalent.
This equipment must only be installed and serviced by qualified electrical personnel.
Failure to follow these instructions will result in death or serious injury.
58 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
DOCA0100EN-02 12/2019 59
MasterPact MTZ1 Normal Operation
The state of the position contacts changes according to the device position during racking-in and racking-
out operations, as shown in the diagram below.
60 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
DOCA0100EN-02 12/2019 61
MasterPact MTZ1 Normal Operation
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See
NFPA 70E or CSA Z462 or local equivalent.
This equipment must only be installed and serviced by qualified electrical personnel.
Failure to follow these instructions will result in death or serious injury.
NOTICE
HAZARD OF EQUIPMENT DAMAGE
Use the provided racking handle to rack the device into or out of chassis.
Do not use power tools for racking.
Do not turn the handle after position release button has popped out.
Failure to follow these instructions can result in equipment damage.
Step Action
1 Press the opening pushbutton to open
the device.
2 Remove the racking handle from its
storage space.
3 Insert the racking handle into the
racking handle socket.
62 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Step Action
1 Push in the position release button.
2 Turn the racking handle
counterclockwise.
Result: The device moves forward in
the chassis.
3 When the disconnected position is
reached, the position release button
pops out and the mechanism blocks the
racking handle.
Result: The device is in the
disconnected position.
DOCA0100EN-02 12/2019 63
MasterPact MTZ1 Normal Operation
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See
NFPA 70E or CSA Z462 or local equivalent.
This equipment must only be installed and serviced by qualified electrical personnel.
Failure to follow these instructions will result in death or serious injury.
NOTICE
HAZARD OF EQUIPMENT DAMAGE
Use the provided racking handle to rack the device into or out of chassis.
Do not use power tools for racking.
Do not turn the handle after position release button has popped out.
Failure to follow these instructions can result in equipment damage.
Step Action
1 Remove the racking handle from its
storage space.
2 Insert the racking handle into the
racking handle socket.
64 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Step Action
1 Push the position release button.
2 Turn the racking handle clockwise.
Result: The device moves back in the
chassis.
3 When the connected position is
reached, the position release button
pops out and the mechanism blocks the
racking handle.
Result: The device is in the connected
position.
DOCA0100EN-02 12/2019 65
MasterPact MTZ1 Normal Operation
Device Removal
NOTICE
HAZARD OF EQUIPMENT DAMAGE
The chassis must be securely fastened when installing or removing the device.
Failure to follow these instructions can result in equipment damage.
Step Action
1 With the device in the disconnected
position (see page 62), discharge the
closing spring by pressing the closing
pushbutton. If the closing spring is
charged, the device closes.
66 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
DANGER
HAZARD OF DEVICE FALLING
Be sure that lifting equipment has lifting capacity for the device being lifted.
Follow manufacturer’s instructions for use of lifting equipment.
Wear hard hat, safety shoes, and heavy gloves.
Failure to follow these instructions will result in death or serious injury.
Lift the device from the chassis rails by using the carrying grip located on the sides of the device.
Device Weights
The following table shows the weights of the different devices available.
DOCA0100EN-02 12/2019 67
MasterPact MTZ1 Normal Operation
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See
NFPA 70E or CSA Z462 or local equivalent.
This equipment must only be installed and serviced by qualified electrical personnel.
Failure to follow these instructions will result in death or serious injury.
NOTICE
HAZARD OF EQUIPMENT DAMAGE
Use the provided racking handle to rack the device into or out of chassis.
Do not use power tools for racking.
Do not turn the handle after position release button has popped out.
Failure to follow these instructions can result in equipment damage.
68 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
DANGER
HAZARD OF DEVICE FALLING
Be sure that lifting equipment has lifting capacity for the device being lifted.
Follow manufacturer’s instructions for use of lifting equipment.
Wear hard hat, safety shoes, and heavy gloves.
Failure to follow these instructions will result in death or serious injury.
NOTICE
HAZARD OF EQUIPMENT DAMAGE
Chassis must be securely fastened when installing or removing the device.
Before mounting the device, make sure that it matches the chassis.
Failure to follow these instructions can result in equipment damage.
Step Action
1 If the chassis is not installed yet in a switchboard or panelboard, securely fasten the chassis on a pallet.
2 Remove the racking handle from its storage space.
3 Check that the chassis indicator is in the disconnected position:
If the chassis indicator is not in the disconnected position, follow the steps on disconnecting the drawout
device (see page 62).
4 Pull out the drawout grips until the
extension rails are fully extended.
DOCA0100EN-02 12/2019 69
MasterPact MTZ1 Normal Operation
Step Action
8 Using both hands, push in the device to
the maximum in the chassis. Take care
not to push the control unit. The rails
stay extended.
70 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Section 2.3
Device Locking Actions
DOCA0100EN-02 12/2019 71
MasterPact MTZ1 Normal Operation
Description
The pushbutton locking cover is an optional accessory for the MasterPact MTZ1 device that forbids access
to the closing and opening pushbuttons:
Together or separately.
By using a padlock (shackle diameter 5–8 mm).
By using a lead seal.
By using screws.
For information on the accessory installation, consult the instruction sheet on the Schneider Electric
website: NVE56769.
72 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Step Action
1 Close the transparent covers of the locking accessory.
NOTE: One or both transparent covers of the locking accessory can be
closed and locked.
2 Lock the transparent covers in place by using a padlock, lead seal, or Padlock
screws.
Lead seal
Screws
DOCA0100EN-02 12/2019 73
MasterPact MTZ1 Normal Operation
Description
Optional padlocks can be used to lock the MasterPact MTZ1 in the open position. When locked the device
cannot be closed either locally with the closing pushbutton or remotely.
To use padlocks to lock the device in the open position, an optional OFF-position locking accessory is
necessary. This accessory allows the use of up to three padlocks with shackle diameter 5–8 mm.
This accessory is not compatible with VSPO OFF-position keylocking accessory, the two accessories
cannot be used at the same time.
For information on the accessory installation, consult the instruction sheet on the Schneider Electric
website: NVE56770.
Step Action
1 Press and hold down the opening pushbutton.
2 With the opening button pressed, pull out the tab of the
off-position padlocking accessory.
74 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Step Action
1 Remove the padlock.
DOCA0100EN-02 12/2019 75
MasterPact MTZ1 Normal Operation
Description
Optional keylocks can be used:
To lock one MasterPact MTZ1 in the open position. When locked the device cannot be closed either
locally with the closing pushbutton or remotely.
To interlock several MasterPact MTZ1 devices locked with the same key.
To use keylocks to lock the device in the open position, an optional OFF-position locking accessory is
necessary.
This accessory is not compatible with the VCPO OFF-position padlocking accessory, the two accessories
cannot be used at the same time.
This accessory is not compatible with the BPFE closing pushbutton.
Ronis keylock Profalux keylock Castell keylock (keylock not Kirk keylock (keylock not
provided) provided)
For information on the accessory installation, consult the instruction sheet on the Schneider Electric
website: NVE56770.
76 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Step Action
1 Press and hold the opening pushbutton.
2 With the opening pushbutton pressed, turn the key clockwise to
lock the device.
5 Check that the device is locked in the open position and cannot
be closed either locally with the closing pushbutton or remotely.
DOCA0100EN-02 12/2019 77
MasterPact MTZ1 Normal Operation
Step Action
1 Put the key in the keylock.
78 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Description
The chassis can be locked in the disconnected position. When the chassis is locked in the disconnected
position, the racking handle cannot be inserted.
The chassis can be locked in the disconnected position:
By up to three padlocks with shackle diameter 5–8 mm.
By optional keylocks.
Ronis keylock Profalux keylock Castell keylock (keylock not Kirk keylock (keylock not
provided) provided)
For information on the accessory installation, consult the instruction sheet on the Schneider Electric
website: NVE56768.
DOCA0100EN-02 12/2019 79
MasterPact MTZ1 Normal Operation
Step Action
1 Check that the chassis indicator is in the
disconnected position.
80 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Step Action
1 Remove the padlocks.
The tab retracts.
DOCA0100EN-02 12/2019 81
MasterPact MTZ1 Normal Operation
Step Action
1 Check that the chassis indicator is in the
disconnected position.
82 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Step Action
1 Put the key in the lock.
DOCA0100EN-02 12/2019 83
MasterPact MTZ1 Normal Operation
Description
The chassis can be locked in any position (connected, test, or disconnected position).
This locking function requires a mechanical adaptation of the chassis, explained in the following procedure.
When the chassis is locked, the racking handle cannot be inserted in the racking handle socket.
The chassis can be locked in any position:
By up to three padlocks with shackle diameter 5-8 mm as standard.
By one or two optional keylocks.
Keylocks can be used in addition to padlocks.
DANGER
HAZARD OF DEVICE FALLING
Be sure that lifting equipment has lifting capacity for the device being lifted.
Follow manufacturer’s instructions for use of lifting equipment.
Wear hard hat, safety shoes, and heavy gloves.
Failure to follow these instructions will result in death or serious injury.
NOTICE
HAZARD OF EQUIPMENT DAMAGE
The chassis must be securely fastened when installing or removing the device.
Failure to follow these instructions can result in equipment damage.
Follow this procedure to adapt the chassis locking mechanism so that the chassis can be locked in any
position.
Stage Description
1 Removing the terminal block identification plate and the chassis front cover. (Refer to the following
procedure)
2 Changing the position of the lock (see page 86).
3 Reinstalling the chassis front cover and the terminal block identification plate (see page 88).
84 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Removing the Terminal Block Identification Plate and the Chassis Front Cover
Before starting the procedure, check that the device is in the disconnected position (see page 62) and
remove the device from the chassis (see page 66).
Step Action
1 Remove the two screws holding
the terminal block identification
plate in place, by using a PZ2
screwdriver.
2 Carefully pull out the terminal
block identification plate.
DOCA0100EN-02 12/2019 85
MasterPact MTZ1 Normal Operation
Step Action
1 Identify the position of the plastic cover
of the lock.
86 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Step Action
6 Use your finger to press down the tab
behind the lock slot.
7 Insert the lock, making sure that the
notch is on the left side.
DOCA0100EN-02 12/2019 87
MasterPact MTZ1 Normal Operation
Reinstalling the Chassis Front Cover and the Terminal Block Identification Plate
Step Action
1 Reinstall the chassis front cover.
2 Screw the front cover into position
with the two screws, by using a
PZ2 screwdriver.
88 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Description
A shutter lock locks the safety shutter in closed position so that a drawout MasterPact MTZ1 device cannot
be connected in its chassis.
The top and bottom safety shutters can be locked independently.
DOCA0100EN-02 12/2019 89
MasterPact MTZ1 Normal Operation
Section 2.4
Device Interlocking Actions
90 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Mismatch Protection
Description
Mismatch protection allows the installation of a MasterPact MTZ1 device only in a chassis with compatible
characteristics.
Mismatch protection offers 35 different combinations that can be selected so that a device can only be
mounted on a chassis with the matching combination.
Accessory
The use of mismatch protection is optional. One mismatch protection accessory is required for each
device.
For information on the accessory installation, consult the instruction sheet available at Schneider Electric
website: NVE35465.
The pin combination selected on the chassis must correspond to the pin combination selected on the
device (see following table). For example, the combination 12 on the chassis corresponds to the
combination CDE on the device.
Pins on the chassis are labeled 1, 2, 3, 4, 5.
Pins on the device are labeled A, B, C, D, E.
DOCA0100EN-02 12/2019 91
MasterPact MTZ1 Normal Operation
92 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Description
With the door interlock:
The equipment door is locked and cannot be opened when the drawout device is in connected or test
position.
The equipment door can be opened when the drawout device is in disconnected position.
The equipment door can be closed with the drawout device in any position.
Accessory
The VPEC door interlock accessory is an optional accessory that is mounted on the left side or on the right
side of the chassis. One door interlock is necessary for each chassis.
For information on the accessory installation, consult the instruction sheet available at Schneider Electric
website: NVE35519.
DOCA0100EN-02 12/2019 93
MasterPact MTZ1 Normal Operation
Step Action
1 Close the equipment door.
94 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Step Action
1 Put the device into the disconnected position
(see page 62).
DOCA0100EN-02 12/2019 95
MasterPact MTZ1 Normal Operation
Description
With the racking interlock installed, a drawout MasterPact MTZ1 device cannot be racked in or out when
the equipment door is open because the racking handle cannot be inserted.
Accessory
The optional VPOC racking interlock can be installed on the right side of the chassis.
For information on the accessory installation, consult the instruction sheet on the Schneider Electric
website: NVE35520.
Step Action
1 Remove the door.
96 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Step Action
4 Replace the door.
DOCA0100EN-02 12/2019 97
MasterPact MTZ1 Normal Operation
Step Action
1 Pull out the racking interlock.
98 DOCA0100EN-02 12/2019
MasterPact MTZ1 Normal Operation
Description
When the cable-type door interlock is installed, the door cannot be opened when the device is closed and
the device cannot be closed when the door is open.
The cable-type door interlock comprises a plate, a lock, and a cable. It is mounted on the right-hand side
of the device.
When the interlock is installed, the mechanical interlock for transfer switches cannot be implemented.
Accessory
The IPA cable-type door interlock is an optional accessory.
For information on the accessory installation, consult the instruction sheet available on the Schneider
Electric website: NVE35521.
DOCA0100EN-02 12/2019 99
MasterPact MTZ1 Normal Operation
Description
The mechanical interlocking for transfer switches between two MasterPact MTZ1 devices prevents the two
interlocked devices from closing at the same time.
For information on the accessory installation, consult the instruction sheet on the Schneider Electric
website:
For Interlocking by cables: NVE35522
For Interlocking by rods: NVE35523
For information on the accessory installation, consult the instruction sheet on the Schneider Electric
website: 51201201AA
Chapter 3
MasterPact MTZ Critical Cases
Definitions
While operating the device, the user may face two critical cases:
The circuit breaker has tripped automatically, interrupting the power supply.
The circuit breaker has not tripped, but the MicroLogic X control unit has detected an alarm:
For a high severity alarm, the service LED is red, indicating that urgent corrective action is required.
For a medium severity alarm, the service LED is orange, indicating that corrective action needs to be
scheduled.
Identifying the Cause of a Trip or Alarm Using the MicroLogic X Control Unit
In critical situations, the cause of a trip or an alarm can be identified locally by using one of the following:
The blue fault-trip reset button on the circuit breaker (A). When the trip button is popped out, the trip has
occurred.
The indicators on the MicroLogic X control unit (see page 105):
The Ready LED (B)
The service LED (C)
The MicroLogic X display screen (D)
The trip cause LEDs (E)
A smartphone with EcoStruxure Power Device app installed to get the trip cause, the trip or alarm
context, and the device ID:
Through NFC
Through Bluetooth
Through USB OTG connection
NOTE: The optional Power Restoration Assistant Digital Module provides assistance with restoring power
after a trip. For more information, refer to DOCA0102EN MasterPact MTZ - MicroLogic X Control Unit -
User Guide.
Using the Display Screen and LEDs to Find the Cause of a Trip
The circuit breaker has tripped automatically, interrupting the power supply, and the blue fault-trip reset
button has popped out.
Ready LED off. Service LED on All LEDs are on. Major MicroLogic X
red. control unit incident
detected during self-test
(see page 109)
Using the Display Screen and LEDs to Find the Cause of an Alarm
The circuit breaker has not tripped, but the MicroLogic X control unit service LED is on.
Ready LED flashing Service LED on All LEDs are off. Medium severity alarm
green. orange. (see page 112)
Reset Sequence
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Do not re-close the device on an electrical fault.
First inspect and, if necessary, repair the downstream equipment.
Failure to follow these instructions will result in death or serious injury.
The table shows the sequence of actions to follow after a trip due to an electrical fault. Further explanation
of each action is given in the following paragraphs.
Step Action
1 Identify the trip cause.
2 Press OK to view details of the trip cause on the display screen.
3 Consult the two trip cause context screens:
Screen 1: Name and settings of the tripping protection, date and time of the trip.
Screen 2: Current values recorded before the trip.
NOTE: You may use the EcoStruxure Power Device app with the Power Restoration Assistant Digital
Module to get support while resetting after a trip due to an electrical fault.
Ready LED Service LED MicroLogic X display Trip cause LEDs Description
screen
Ready LED Service LED MicroLogic 2.0 X,
flashing green. off. 5.0 X, 6.0 X, 7.0 X:
trip due to the long-
time protection.
NOTE: Diagnostic assistance can be obtained by using a smartphone running the EcoStruxure Power
Device app.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See
NFPA 70E or CSA Z462 or local equivalent.
This equipment must be installed and serviced by qualified electrical personnel.
Turn off all power supplying this equipment before performing maintenance inspections.
Assume that all circuits are live until they are de-energized, tested, grounded, and tagged. Consider
all sources of power, including the possibility of backfeeding and control power.
Always use a properly rated voltage sensing device to confirm that power is off.
Replace all devices, doors, and covers before turning on power to this equipment.
Beware of potential hazards and carefully inspect the work area for tools and objects that may have
been left inside the equipment.
Failure to follow these instructions will result in death or serious injury.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Do not re-close the device on an electrical fault.
First inspect and, if necessary, repair the downstream equipment.
Failure to follow these instructions will result in death or serious injury.
The feed must be isolated before inspecting the electrical equipment downstream of the protection.
The fact that a circuit breaker has tripped does not remedy the cause of the electrical fault detected on the
downstream electrical equipment.
Inspecting the Circuit Breaker and Switchboard After a Trip on Short Circuit
After a trip on short circuit due to short-time or instantaneous protection, the circuit breaker and
switchboard must be inspected for smoke deposits or cracks in the device casing.
Refer to DOCA0099EN MasterPact MTZ - IEC Circuit Breakers and Switch-Disconnectors - Maintenance
Guide and contact your field service representative.
Resetting the Circuit Breaker After a Trip Due to an Incident Detected by the MicroLogic X Self-tests
Reset Sequence
The following table shows the sequence of actions to take after a trip due to an incident detected by the
MicroLogic X control unit. Further explanation of each action is given in the following paragraphs.
Step Action
1 Identify the trip cause.
2 Press OK to view details of the trip cause on the display screen:
A code that identifies the trip cause.
A trip message describing the cause of the incident.
The date and time that the incident occurred.
3 Consult the list of possible detected incidents (see page 109) and perform the actions recommended to
restart after the trip.
4 Press OK to acknowledge the trip and return to the Home menu.
5 Reset the circuit breaker (see page 48).
6 Press the Test/Reset button for 3 seconds to reset the latched events and switch off the trip cause LEDs
and the service LED.
7 When the circuit breaker is ready to close, re-close it (see page 45).
Diagnosing Alarms
Diagnosis Sequence
The following table shows the sequence of actions to take after an alarm is detected by the MicroLogic X
control unit. Further explanation of each action is given in the following paragraphs.
Step Action
1 Identify the alarm detected.
2 Press OK to view details of the alarm detected on the display screen:
An alarm message.
The date and time that the alarm occurred.
3 Consult the list of alarm messages in the following tables and perform the actions recommended.
4 Press OK to acknowledge the alarm and return to the Home menu.
5 Press the Test/Reset button for 3 seconds to reset the latched events and switch off the trip cause LEDs
and the service LED.
Two levels of alarm are detected and indicated by the color of the service LED:
Red for high-severity detected alarms.
Orange for medium-severity detected alarms.
Ready LED Service LED on All LEDs are off. Medium severity alarm
flashing green. orange. (see page 112)
For more information about the maximum number of operations for individual parts, refer to DOCA0099EN
MasterPact MTZ - IEC Circuit Breakers and Switch-Disconnectors - Maintenance Guide.
Contact your Schneider Electric field service representative for more information about who can carry out
the recommended actions.
Diagnosis Sequence
The following table shows the sequence of actions to take after an error is detected by the MicroLogic X
control unit. Further explanation of each action is given in the following paragraphs.
Step Action
1 Identify the error detected.
2 Consult the list of error messages (see page 119) and perform the actions recommended.
3 Press OK to acknowledge the error and return to the Home menu.
4 Press the Test/Reset button for 3 seconds to reset the latched events.
Contact your Schneider Electric field service representative for more information about who can carry out
the recommended actions.
Chapter 4
MasterPact MTZ Commissioning
Introduction to Commissioning
Overview
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See
NFPA 70E, CSA Z462, NOM 029-STPS, or local equivalent.
This equipment must only be installed and serviced by qualified electrical personnel.
Unless specified otherwise in the commissioning procedures, all operations (inspection, test, and
preventive maintenance) must be carried out with the device, the chassis, and the auxiliary circuits de-
energized.
Check that the device and the chassis are de-energized on the upstream and downstream terminals.
Always use a properly rated voltage sensing device to confirm that the device, the chassis, and the
auxiliary circuits are de-energized.
Install safety barriers and display a danger sign.
During the tests, it is strictly forbidden for anyone to touch the device, the chassis, or the conductors
while voltage is applied.
Before putting the equipment back into operation, it is mandatory to check that all connections are
made with the correct tightening torque, there are no tools or objects inside the equipment, all devices,
doors, and protective covers are in position, and the device is off (open position).
Failure to follow these instructions will result in death or serious injury.
This chapter details the testing and commissioning procedure for MasterPact MTZ devices that must be
done before the device can be accepted as fit for service and connected to a power supply.
The commissioning procedure must be done by an authorized commissioning engineer with appropriate
training and experience:
Only qualified electrical personnel with training and experience on low voltage circuits must perform the
work described in this chapter.
Personnel must understand the hazards involved in working with or near low-voltage equipment. Such
work must be performed only after reading the complete set of instructions.
Some inspections or procedures require that certain parts of the electrical system remain energized at
hazardous voltage during the procedure. Observe all safety messages (Danger, Warning, Caution)
throughout this chapter and the corresponding instruction notices.
Wear personal protective equipment, recognize potential hazards, and take adequate safety
precautions when performing the procedures outlined in this chapter and the corresponding instruction
notices.
The commissioning procedure assumes that the following conditions are met at the start of the procedure:
The device is not connected to a power system or a control system.
A drawout device is in the disconnected position.
The device is not connected to a communication network.
The results of all observations, tests, adjustments, together with any relevant comments must be recorded
on the appropriate form, if applicable.
Wherever possible, testing must be done without disconnecting or disturbing existing wiring.
Scope
The commissioning procedure applies to the MasterPact MTZ intelligent modular unit (IMU), made up of:
MasterPact MTZ circuit breaker with its MicroLogic X control unit and optional ULP modules:
One IFE, EIFE, or IFM communication interface
One or two IO modules
Equipment
The following equipment is required to do the tests detailed in the commissioning procedure:
Insulation resistance tester
Multimeter
A PC equipped with the latest version of EcoStruxure Power Commission software
A USB to mini USB cable (LV850067SP) to connect the PC to the MicroLogic X control unit
Test Form
A test form (see page 131) is proposed to guide you through the commissioning procedure and to record
the results of the commissioning tests. Each test is described in detail in the Commissioning chapter.
Only do the tests required, depending on the MasterPact MTZ type and the functions in use.
Visual Inspection
Step Action
1 Record the equipment identification, including substation name, switchboard name, MasterPact MTZ
device type, MicroLogic X model type and serial number, MicroLogic X type, and protection settings.
2 Check that the device is undamaged, correctly mounted, and securely fastened in the switchboard.
3 Check the 3-phase clearance at terminal blocks.
4 Check that there is no debris remaining at the back of the device housing/enclosure.
5 Check that the ground terminals of the device are securely connected with the correct grounding cables.
6 Check that all external surfaces are undamaged.
7 Rectify any non-conformities, if possible. All equipment non-conformities must be referred to asset
management.
Step Action
1 Connect a PC running EcoStruxure Power Commission software by using a cable connected to the mini
USB port on the front face of the MicroLogic X control unit.
2 Establish a connection. EcoStruxure Power Commission software reads the parameters of the control
unit.
3 On EcoStruxure Power Commission, use the Overall System firmware status/compatibility matrix to
display:
The installed firmware version of the IMU devices (MicroLogic X control unit and ULP modules).
The latest firmware version of the devices that are available on the Schneider Electric System
Updates Internet site.
The recommended actions to get a compatible system.
MicroLogic X Settings
NOTICE
RISK OF UNINTENDED OPERATION
The device must only be configured and set by qualified personnel, using the results of the installation
protection system study.
During commissioning of the installation and following any modification, check that the MicroLogic X
configuration and protection function settings are consistent with the results of this study.
MicroLogic X protection functions are set by default to the minimum value, except for the long time
protection function which is set to the maximum value, by default.
Failure to follow these instructions can result in equipment damage.
Check the settings with EcoStruxure Power Commission software connected to the MicroLogic X control
unit.
Step Action
1 Connect a PC running EcoStruxure Power Commission software by using a cable connected to the mini
USB port on the front face of the MicroLogic X control unit.
2 Establish a connection. EcoStruxure Power Commission software reads the parameters of the control
unit.
3 Check that the settings read in the control unit match the requirements of the application. If necessary,
correct the settings with EcoStruxure Power Commission software:
The protection settings must be defined according to the installation protection system study.
Other settings must be defined according to the application.
NOTE: The protection functions available depend on the type of MicroLogic X control unit and its
associated optional Digital Modules.
Tests
Overview
The tests to do while commissioning an MTZ device are described in this section:
Functional checks
Check of MCH gear motor (if fitted)
Check of M2C programmable contacts and IO module (if fitted)
Check of ESM ERMS switch module (if fitted)
Check of electrical continuity
Check of high-voltage insulation
Check of MicroLogic X Ready LED status
Test of the tripping mechanism with EcoStruxure Power Commission software
Test of the tripping mechanism with the test button (MicroLogic 6.0 X or 7.0 X control units)
Only do the tests required, depending on the MasterPact MTZ type and the functions in use, and record
the results on the test form (see page 131). In the event of non-conformance, the result must be recorded
and the MasterPact MTZ device must not be accepted into service.
Functional Checks
Follow this procedure to check the operation of the MasterPact MTZ device and record the results on the
test form.
Step Action
1 Manually charge the mechanism by pulling the spring charging handle down.
2 Close the device. Check the closing of the device in the different control modes and means designed for
the application.
3 Open the device. Check the opening of the device in the different control modes and means designed for
the application.
Step Action
1 Remove the MCH gear motor power supply.
2 Do an opening/closing/opening cycle to discharge the mechanism.
3 With the device in the open position and the mechanism discharged, check electrical continuity between
terminals B1 and B2, and electrical non-continuity between terminals B1 and B3.
4 Manually charge the mechanism.
5 Reconnect the MCH gear motor power supply. The device closes and the mechanism is automatically
charged.
6 Check electrical continuity between terminals B1 and B3.
7 Operate the device several times to check that the spring mechanism automatically recharges after every
closing operation.
Step Action
1 Connect a PC running EcoStruxure Power Commission software by using a cable to the mini USB port
on the front face of the MicroLogic X control unit.
2 Force the state of both inputs of the M2C programmable contacts and check that the operation is
correct.
3 Force the state of the six digital inputs and three outputs of the one or two IO modules in the IMU to
check the wiring to the circuit breaker. Check that the operation is correct.
Step Action
1 Make sure that the MicroLogic X control unit is powered permanently with a 24 Vdc power supply.
2 Connect the ESM ERMS switch module to an external switch with a 24 Vdc or 24—120 Vac power
supply.
3 Activate the ERMS function by moving the external switch to the Engage position. Check that:
The ERMS LED on the front face of the MicroLogic X control unit lights blue.
The MicroLogic X control unit display screen is lit with a blue backlight.
The message ERMS Engaged is displayed on the MicroLogic X control unit display screen.
4 Disengage the ERMS function by moving the external switch to the Disengage position, and check after
3 s that the MicroLogic X control unit returns to its original state.
Step Action
1 Close the device.
2 Check electrical continuity, for each of the phases, between the upper and lower power terminals:
For fixed device: on the power terminals
For the drawout device: on the chassis power terminals, with the device in the connected position
CAUTION
DETERIORATION OF VPS MODULE
Disconnect the VPS module by pulling it out to the disconnected position before running a dielectric test
on the equipment.
Failure to follow these instructions can result in injury or equipment damage.
Follow this procedure to check insulation resistance and record the results on the test form.
Step Action
1 Disconnect the VPS module and unplug any cables from the mini USB port on the front face of the
MicroLogic X control unit.
2 Close the MasterPact MTZ device.
3 Measure the insulation resistance using a 500 Vdc insulation resistance tester between one of the
phases and the other two phases grounded. Repeat for each phase.
4 Open the MasterPact MTZ device by pressing the opening pushbutton.
5 Measure the insulation resistance using a 500 Vdc insulation resistance tester between one of the
phases and ground, with all other phases grounded. Repeat for each phase.
6 Check that the insulation resistance is above 5 MΩ in each case. If this result is not obtained, contact
your field service representative.
Step Action
1 Provide power to the MicroLogic X control unit, for example, by connecting a PC or Mobile Power Pack
to the mini USB port on the front face.
2 Check that the MicroLogic X Ready LED is flashing green.
The Ready LED flashes green to indicate that:
The sensors are correctly wired.
The tripping mechanism is functioning correctly.
The MicroLogic X control unit is functioning correctly.
3 If the Ready LED is not flashing green, refer to chapter Critical Cases (see page 101).
Step Action
1 Close the circuit breaker.
2 Connect a PC running EcoStruxure Power Commission software by using a cable to the mini USB port
on the front face of the MicroLogic X control unit.
3 On EcoStruxure Power Commission software, select the circuit breaker and connect to it.
4 Force the circuit breaker to trip by clicking the Force Trip button on the EcoStruxure Power Commission
screen. This action is password-protected.
5 Check that the circuit breaker is open.
6 Check that the blue fault-trip reset button has popped out.
7 Check that the Isd/Ii LED is on.
8 Check that the SDE contacts have switched.
9 After the test, reset the circuit breaker.
Test of the Tripping Mechanism with the Test Button (MicroLogic 6.0 X and 7.0 X Control Units)
Follow this procedure to test the tripping mechanism of the circuit breaker when fitted with a
MicroLogic 6.0 X or 7.0 X control unit, and record the results on the test form.
Step Action
1 Close the circuit breaker.
2 Use a thin screwdriver to briefly push in (<1 s) the test button on the control unit.
3 Check that the circuit breaker is open.
4 Check that the blue fault-trip reset button has popped out.
5 Check that the Ig/IΔn LED is on.
6 Check that the SDE contacts have switched.
7 After the test, reset the circuit breaker.
Communication Tests
Step Action
1 Connect a PC running EcoStruxure Power Commission software by using an RJ45 cable to a
communication network, on the IFE or EIFE Ethernet interface, or IFM interface, for example.
2 In EcoStruxure Power Commission software, at Create report → Communication test & report, select
devices to be tested from the list of communicating devices defined in the project.
3 Click Run test. All selected devices are tested.
4 Results are displayed at the end of the test.
5 Generate the communication test report with EcoStruxure Power Commission software, and save or
print the project report as needed.
Step Action
1 Connect a PC running EcoStruxure Power Commission software by using an RJ45 cable to a
communication network, on the IFE or EIFE Ethernet interface, or IFM interface, for example.
2 Check that the control mode is set to Auto: Remote.
3 In EcoStruxure Power Commission software, select the circuit breaker and connect to it.
4 Click the Device tab to access the Open and Close buttons.
5 Check that it is possible to open and close the MasterPact MTZ device remotely. These actions are
password-protected.
Final Checks
After completing the commissioning tests, check the following:
Step Action
1 Check that connections are made with the correct tightening torque, that there are no tools or objects
inside the equipment, and that all devices, doors, and protective covers are in position.
2 Check that the device is off (open position) and the closing spring is charged.
Identification
Signature:
Preliminary Checks
Test of the Tripping Mechanism for MicroLogic 6.0 X and 7.0 X Control Units
Communication Tests
Final Checks
Chapter 5
MasterPact MTZ Troubleshooting
Introduction to Troubleshooting
Presentation
This chapter contains information for troubleshooting problems in a working system. It assumes that the
system is correctly installed and that all the commissioning tests (see page 121) have been completed
successfully. The troubleshooting operations are described under the following headings:
Chassis operation
Unexpected tripping
Mechanical control operations
Electrical control operations
Control operations from EcoStruxure Power Device app
Control operations from IO module
Control operations from EcoStruxure Power Commission software
Control operations from IFE/EIFE webpages
Control operations from communication network
Control operations from FDM128 display
Layer Model
When troubleshooting the device, it is useful to consider a layer model. There are four layers:
Communication network
Direct connection
Electrical
Mechanical
Communication network
Direct communication
Electrical
Mechanical
If the troubleshooting actions for a layer are not successful, go to the next layer until you reach the
Mechanical layer. If you cannot solve the problem after troubleshooting the Mechanical layer, contact your
field service representative.
Definition
Chassis operation includes the following:
Racking in and racking out the drawout device
Locking and unlocking the chassis
Troubleshooting
Definition
Unexpected tripping is tripping that is not caused by a protection function during normal operation or by
tests.
Troubleshooting
Definition
Mechanical control operations are operations that are made using the opening or closing pushbuttons.
Definition
Electrical control operations are operations that are made by an electrical order through a voltage release
or by an external pushbutton that is directly connected to a voltage release.
Additional Checks
If the troubleshooting actions described above do not work, refer to the troubleshooting information for
Mechanical Control Operations (see page 140).
Definition
Control operations include commands to open and close the device from the EcoStruxure Power Device
app.
Device Cannot be Controlled from the EcoStruxure Power Device App Connected Through Bluetooth
Additional Checks
If the troubleshooting actions described above do not work, the problem might be in the mechanical or
electrical operations of the device. Refer to the troubleshooting information for Mechanical Control
Operations (see page 140) and Electrical Control Operations (see page 141).
Definition
Control operations include commands to open and close the device from the IO module with the Breaker
Operation predefined application.
For information about control operations from the IO module, refer to DOCA0055EN Enerlin'X IO -
Input/Output Application Module for One IEC Circuit Breaker - User Guide.
Additional Checks
If the troubleshooting actions described above do not work, the problem might be in the mechanical or
electrical operations of the device. Refer to the troubleshooting information for Mechanical Control
Operations (see page 140) and Electrical Control Operations (see page 141).
Definition
Control operations include commands to open and close the device from EcoStruxure Power Commission
software.
Device Cannot be Controlled from EcoStruxure Power Commission Software Connected to a Mini USB Port
Device Cannot be Controlled from EcoStruxure Power Commission Software Connected by IFE, EIFE, or IFM Interface
Additional Checks
If the troubleshooting actions described above do not work, the problem might be in the mechanical or
electrical operations of the device. Refer to the troubleshooting information for Mechanical Control
Operations (see page 140) and Electrical Control Operations (see page 141).
Definition
Control operations include commands to open and close the device from IFE or EIFE webpages.
For information about control operations from IFE or EIFE webpages, refer to the following guides:
DOCA0084EN Enerlin'X IFE - Ethernet Switchboard Server - User Guide
DOCA0142EN Enerlin'X IFE - Ethernet Interface for One IEC Circuit Breaker - User Guide
DOCA0106EN Enerlin'X EIFE - Embedded Ethernet Interface for One MasterPact MTZ Drawout Circuit
Breaker - User Guide
Additional Checks
If the troubleshooting actions described above do not work, the problem might be in the mechanical or
electrical operations of the device. Refer to the troubleshooting information for Mechanical Control
Operations (see page 140) and Electrical Control Operations (see page 141).
Definition
Control operations include commands to open and close the device from the communication network.
For information about control operations from the communication network, refer to the following guides:
DOCA0105EN MasterPact MTZ - Modbus Communication Guide
DOCA0162EN MasterPact MTZ - IEC 61850 Communication Guide
Device Cannot be Controlled with a Remote Controller Connected from IFE, EIFE, or IFM Interface
Additional Checks
If the troubleshooting actions described above do not work, the problem might be in the mechanical or
electrical operations of the device. Refer to the troubleshooting information for Mechanical Control
Operations (see page 140) and Electrical Control Operations (see page 141).
Definition
Control operations include commands to open and close the device from the FDM128 display.
For information about control operations from the FDM128 display, refer to DOCA0037EN
Enerlin’X FDM128 - Ethernet Display for Eight Devices - User Guide.
Additional Checks
If the troubleshooting actions described above do not work, the problem might be linked to the
communication network. Refer to the troubleshooting information for the communication network
(see page 150).
Chapter 6
Schneider Electric Green Premium™ Ecolabel
Description
Green Premium by Schneider Electric is a label that allows you to develop and promote an environmental
policy while preserving your business efficiency. This ecolabel is compliant with up-to-date environmental
regulations.
Step Action
1 From www.se.com, select Support → Additional Links → Green Premium Eco Label.
2 Click Find Green Premium Products to open the search tool webpage.
3 Fill in the fields:
Enter the commercial reference or product range of the product to search for.
Optional: Enter the manufacturing date code of the product with format YYWW. By default, this field is
filled with the date of the search.
4 To search for several products simultaneously, click the Add product button, and then fill in the fields.
5 Click Check product(s) to generate a report of the environmental criteria available for the products with
the entered commercial references.
Environmental Criteria
The Green Premium ecolabel provides documentation on the following criteria about the environmental
impact of the products:
RoHs: European Union Restriction of Hazardous Substances (RoHS) directive.
REACh: European Union Registration, Evaluation, Authorization, and Restriction of Chemicals
regulation.
PEP: Product Environmental Profile.
EoLI: End of Life Instructions.
RoHs
Schneider Electric products are subject to RoHS requirements at a worldwide level, even for the many
products that are not required to comply with the terms of the regulation. Compliance certificates are
available for products that fulfill the criteria of this European initiative, which aims to eliminate hazardous
substances.
REACh
Schneider Electric applies the strict REACh regulation on its products at a worldwide level, and discloses
extensive information concerning the presence of SVHC (Substances of Very High Concern) in all of these
products.
PEP
Schneider Electric publishes complete set of environmental data, including carbon footprint and energy
consumption data for each of the life cycle phases on all of its products, in compliance with the
ISO 14025 PEP ecopassport program. PEP is especially useful for monitoring, controlling, saving energy,
and/or reducing carbon emissions.
EoLI
These instructions provide:
Recyclability rates for Schneider Electric products.
Guidance to mitigate personnel hazards during the dismantling of products and before recycling
operations.
Part identification for recycling or for selective treatment, to mitigate environmental hazards/incompati-
bility with standard recycling processes.
Schneider Electric Industries SAS As standards, specifications and designs change from time to time, please ask for confirmation
35, rue Joseph Monier of the information given in this publication.
CS30323
F - 92506 Rueil Malmaison Cedex
www.schneider-electric.com 12/2019