Professional Documents
Culture Documents
Packet Tracer - Troubleshoot Enterprise Network: Objectives
Packet Tracer - Troubleshoot Enterprise Network: Objectives
Objectives
Part 1: Verify Switching Technologies
Part 2: Verify DHCP
Part 3: Verify Routing
Part 4: Verify WAN Technologies
Part 5: Verify Connectivity
Scenario
This activity uses a variety of technologies that you have encountered during your CCNA studies, including
IPv4 routing, IPv6 routing, port security, EtherChannel, DHCP, and NAT. Your task is to review the
requirements, isolate and resolve any problems, and then document the s teps you took to verify the
requirements.
The company replaced routers R1 and R3 to accommodate a fiber connection between the locations.
Configurations from the previous routers with serial connections were modified and applied as a starting
configuration. IPv6 is being tested on a small portion of the network and needs to be verified.
Note: Passwords have been removed for ease of troubleshooting in this exercise. The typical password
protections should be reapplied; however, the activity will not grade those items.
Addressing Table
Device Interface IP Address / Prefix Default Gateway
R2 G0/0
2001:db8:b:209::1/64
R2
G0/1 192.168.20.1 /30 N/A
N/A
R2 G0/1
2001:db8:b:20::1/64
R2
S0/0/0 10.1.1.2 /30 N/A
R2
G0/1/0 10.2.2.1 /30 N/A
N/A
R2 G0/1/0
2001:db8:b:10:2::1/64
R3 G0/1.30 192.168.30.1 /24 N/A
R3
G0/1.40 192.168.40.1 /24 N/A
R3
G0/1.50 192.168.50.1 /24 N/A
N/A
R3 G0/1.50
2001:db8:b:50::1/64
© 2017 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 6 www.netacad.com
Packet Tracer - Troubleshoot Enterprise Network
R3
G0/1.99 N/A N/A
R3
G0/1/0 10.3.3.2 /30 N/A
R3
G0/2/0 10.2.2.2 /30 N/A
N/A
R3 G0/2/0
2001:db8:b:10:2::2/64
S1 VLAN10 192.168.10.2 /24 192.168.10.1
Instructions
a. Port security is configured to only allow PC1 to access S1's F0/3 interface. All violations should disable
the interface.
Issue the command on S1 to display the current port security status.
S1# show port-security
b. Enter interface configuration mode for interface F0/3 and set up port security.
S1(config-if)# switchport port-security
S1(config-if)# switchport port-security mac-address sticky
c. Devices in the LAN on S1 should be in VLAN 10. Display the current state of VLAN configuration.
Question:
© 2017 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 6 www.netacad.com
Packet Tracer - Troubleshoot Enterprise Network
© 2017 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 6 www.netacad.com
Packet Tracer - Troubleshoot Enterprise Network
© 2017 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 6 www.netacad.com
Packet Tracer - Troubleshoot Enterprise Network
Question:
Notice the traffic is being sent via the S0/1/0 interface as opposed to the G0/0/0 interface.
b. The original configurations that came from the previous serial WAN connections were transferred to the
new devices. Compare the G0/0/0 interface and Serial0/1/0 interface settings. Notice they both have an
OSPF cost value set. Remove the OSPF cost setting from the G0/0/0 interface. It will also be necessary
to remove the setting on the link on R3 that connects to R1.
R1(config)# int g0/0/0
© 2017 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of 6 www.netacad.com
Packet Tracer - Troubleshoot Enterprise Network
© 2017 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 6 of 6 www.netacad.com