Professional Documents
Culture Documents
Mil HDBK 1025 10
Mil HDBK 1025 10
MIL-HDBK-1025/10
1 DECEMBER 1998
_________________
SUPERSEDING
NAVFAC P-1060
DATED JULY 1990
DEPARTMENT OF DEFENSE
HANDBOOK
SAFETY OF ELECTRICAL
TRANSMISSION AND DISTRIBUTION SYSTEMS
FOREWORD
This handbook is approved for use by the Department of the Navy and is available for use by all
Departments and Agencies of the Department of Defense.
This handbook has been developed from selection of the best safety practices of the Naval
Facilities Engineering Command (NAVFACENGCOM), other Government agencies, and the
private sector. This handbook was prepared using, to the maximum extent feasible, national
professional society, association, and institute standards. Deviations from this criteria cannot be
made without prior approval of NAVFACENGCOM Criteria Office. This handbook is for
guidance only. This handbook cannot be cited as a requirement. If it is, the Contractor does not
have to comply.
Beneficial comments (recommendations, additions, deletions) and any pertinent data that may be
of use in improving this document should be addressed to: Commander, Attention NAVFAC
Criteria Office, Naval Facilities Engineering Command, 1510 Gilbert Street, Norfolk, VA 23511-
2699.
ii
MIL-HDBK-1025/10
CONTENTS
PAGE
Section 1 INTRODUCTION
1.1 Scope...................................................................................................... 1
1.2 Cancellation ............................................................................................ 1
1.3 Handbook Presentation ........................................................................... 1
1.3.1 Tabular Method ...................................................................................... 1
1.3.2 Nontabular Method................................................................................. 1
1.3.3 Warnings, Cautions, and Notes ............................................................... 1
1.4 Handbook Content.................................................................................. 2
1.4.1 Applicable Documents ............................................................................ 2
1.4.2 Definitions .............................................................................................. 2
1.4.3 General Safety Practices.......................................................................... 2
1.4.4 Work on De-energized or Energized Line Safety Requirements............... 2
1.4.5 Substations and Switchgear..................................................................... 2
1.4.6 Overhead Lines and Associated Electrical Components ........................... 2
1.4.7 Underground Cables, Structures, and Associated Electrical Components. 2
1.4.8 Shore-to-Ship Electrical Power Connections ........................................... 2
Section 3 DEFINITIONS
3.1 Abbreviations and Acronyms Used in This Handbook.............................. 5
3.2 Definitions .............................................................................................. 6
PAGE
4.2.2 Work Area Protection ............................................................................. 8
4.2.3 Normal Environmental Impacts ............................................................... 8
4.2.3.1 Work in Elevated Positions or Near Waterways ...................................... 8
4.2.3.2 Work in Confined or Enclosed Spaces..................................................... 8
4.2.3.3 Noise Control ......................................................................................... 8
4.2.3.4 Lighting .................................................................................................. 8
4.2.4 Hazardous Environmental Impacts .......................................................... 8
4.2.4.1 Asbestos ................................................................................................. 9
4.2.4.2 Polychlorinated Biphenyls (PCB) ............................................................ 9
4.2.4.3 Sulfur Hexafluoride (SF6)........................................................................ 9
4.2.4.4 Wood Product Preservative Treatments .................................................. 9
4.2.5 Explosive or Hazardous Vapors .............................................................. 9
4.3 Reminder of Electrical Hazards in the Field ........................................... 10
4.3.1 Dangers From Electric Shock................................................................ 10
4.3.2 Danger From Arcs and Blasts................................................................ 11
4.4 Protection Against Hazards................................................................... 11
4.4.1 General Body Protection ....................................................................... 11
4.4.2 Safety Equipment and Tools.................................................................. 14
4.4.2.1 Rubber Protective Equipment................................................................ 14
4.4.2.2 Plastic Guard Equipment....................................................................... 14
4.4.2.3 Live-Line Tools .................................................................................... 14
4.4.2.4 Other Safety Requirements.................................................................... 15
4.5 General Safety Observances .................................................................. 15
4.6 Worker/Crew Responsibilities ............................................................... 15
4.6.1 Levels of Responsibility......................................................................... 15
4.6.2 Qualifications ........................................................................................ 15
4.6.2.1 Qualified Workers................................................................................. 15
4.6.2.2 Unqualified Workers ............................................................................. 15
4.6.3 Mishap Handling ................................................................................... 16
4.6.3.1 Knowing What To Do........................................................................... 16
4.6.3.2 Work Injuries and Mishap Reports ........................................................ 18
4.6.3.3 Rescue Operations ................................................................................ 18
4.7 Lockout/Tagout/Tryout of Hazardous Energy Sources.......................... 18
4.8 Training ................................................................................................ 19
4.8.1 Programs .............................................................................................. 20
4.8.2 Standard Operating Procedures/Job Hazard Analysis............................. 22
iv
MIL-HDBK-1025/10
...................................................................................................... PAGE
5.1.1 Safe Working Distances ........................................................................ 23
5.1.2 Work Methods in Relation To Worker’s Safety..................................... 25
5.1.2.1 De-energized Electrical Line Work........................................................ 25
5.1.2.2 Energized Electrical Line Work............................................................. 25
5.1.2.3 Number of Qualified Workers Per Hazard Exposure.............................. 26
5.1.3 Verifying Electrical Systems and Equipment Provisions......................... 27
5.1.4 Safety Hazard Detection Devices .......................................................... 27
5.1.4.1 Potential Differences ............................................................................. 28
5.1.4.2 Phasing Testers ..................................................................................... 28
5.1.4.3 Combustible Gas/Oxygen Detectors ...................................................... 28
5.1.4.4 Aerial-Lift Bucket Truck Leakage-Current Monitoring.......................... 28
5.2 De-energized Line Work Prescheduling................................................. 28
5.2.1 Preparation Responsibility ..................................................................... 29
5.2.2 Safety Basics......................................................................................... 29
5.2.2.1 Hazardous Energy Elimination .............................................................. 29
5.2.2.2 Lockout/Tagout/Tryout Instructions ..................................................... 30
5.2.2.3 Lock and Tag Color Coding.................................................................. 31
5.3 Grounding Provisions............................................................................ 31
5.3.1 Why Temporary Grounds are Necessary................................................ 32
5.3.2 Equipotential (Single Point) Grounding ................................................. 32
5.3.3 Placement of Grounds ........................................................................... 33
5.3.3.1 Approach Distances .............................................................................. 33
5.3.3.2 Potential Differences ............................................................................. 33
5.3.4 Temporary Grounding System Components .......................................... 34
5.3.4.1 Grounding Clamps ................................................................................ 34
5.3.4.2 Grounding Cable................................................................................... 34
5.3.4.3 Grounding Ferrules ............................................................................... 35
5.3.4.4 Grounding Cluster Bars......................................................................... 35
5.3.5 Temporary Grounding of Aerial Lines ................................................... 36
5.3.6 Temporary Grounding of Substation Current-Carrying Equipment
Components........................................................................................ 36
5.3.7 Aerial Lift Truck Vehicle Grounding ..................................................... 39
5.3.8 Temporary Grounding of Underground Lines........................................ 40
5.3.9 Opening or Splicing De-energized Conductors ...................................... 40
5.3.10 Grounding for Stringing and Removing Lines........................................ 41
5.4 Energized Electrical Line Work............................................................. 43
5.4.1 Permitted Electrical Line Work Methods............................................... 43
5.4.2 Voltage Levels and Approved Work Methods and Equipment............... 43
5.4.2.1 Rubber Goods....................................................................................... 44
5.4.2.2 Insulating Tools .................................................................................... 44
v
MIL-HDBK-1025/10
...................................................................................................... PAGE
5.4.2.3 Insulating Guards .................................................................................. 45
5.4.3 Prework Procedures.............................................................................. 46
5.4.4 General Job-in-Progress Procedures ...................................................... 47
vi
MIL-HDBK-1025/10
...................................................................................................... PAGE
6.5.2 Oil Switches.......................................................................................... 56
6.5.3 Similar Switching Sections .................................................................... 56
6.6 Fusing Safety ........................................................................................ 56
6.6.1 Fuse Handling ....................................................................................... 56
6.6.2 Operation of Energized Fuses................................................................ 56
6.6.3 Open Fuse Holder ................................................................................. 57
6.6.4 Closed-Position Fuse Locking ............................................................... 57
6.6.5 Bypassing.............................................................................................. 57
6.7 Energy-Storing Protective Device Safety............................................... 57
6.7.1 Surge Arresters ..................................................................................... 57
6.7.1.1 Surge Arrester Contact ......................................................................... 57
6.7.1.2 Disconnecting Surge Arresters .............................................................. 57
6.7.2 Choke Coils .......................................................................................... 58
6.7.3 Capacitors............................................................................................. 58
6.7.3.1 Capacitor Discharge Circuits................................................................. 58
6.7.3.2 Coupling Capacitors.............................................................................. 58
6.8 Instrument Transformer Safety.............................................................. 58
6.8.1 Voltage (Potential) Transformers .......................................................... 59
6.8.1.1 Fuse Replacement ................................................................................. 59
6.8.1.2 Supervisory Requirements..................................................................... 59
6.8.2 Current Transformers............................................................................ 60
6.8.2.1 Circuit Opening..................................................................................... 60
6.9 Power Transformer and Regulator Safety.............................................. 60
6.9.1 Power Transformers.............................................................................. 60
6.9.2 Voltage Regulators ............................................................................... 61
6.10 Metal Clad Switchgear Safety ............................................................... 61
6.10.1 Before Circuit Breaker Drawout Requirements ..................................... 61
6.10.2 Circuit Breaker Maintenance ................................................................. 62
6.10.3 Safety Precautions After Circuit Breaker Maintenance........................... 62
6.11 Network Protector Safety ..................................................................... 62
6.11.1 Closing Network Protectors .................................................................. 63
6.11.2 Network Protector Maintenance Safety................................................. 63
6.11.3 After Network Protector Maintenance................................................... 64
6.12 Storage Battery Safety .......................................................................... 64
6.13 Requirements for Safely Phasing or Connecting of Circuits.................... 65
vii
MIL-HDBK-1025/10
...................................................................................................... PAGE
7.2 Aerial Lifts............................................................................................ 66
7.2.1 Operation of Aerial Lift Equipment Near Energized Electrical
Facilities............................................................................................ 67
7.2.2 Types of Aerial Lifts ............................................................................. 67
7.2.3 Aerial Lift Manufacturing Requirements................................................ 67
7.2.4 Aerial Lift Safety................................................................................... 68
7.2.5 Other Aerial Lift Requirements.............................................................. 69
7.2.6 Bucket Safety Precautions..................................................................... 70
7.2.7 Insulated Buckets.................................................................................. 71
7.2.8 Aerial Lift Maintenance......................................................................... 71
7.3 Pole Handling Operations...................................................................... 72
7.3.1 Direction of Aerial Lift for Installations ................................................. 72
7.3.2 Pole Contact Precautions ...................................................................... 72
7.3.3 Facility Receipt ..................................................................................... 72
7.3.4 Ground Handling .................................................................................. 73
7.3.5 Temporary Pole Storage ....................................................................... 74
7.3.6 Hauling Poles........................................................................................ 74
7.4 Pole Installation Requirements .............................................................. 75
7.4.1 Pole Holes ............................................................................................ 75
7.4.2 Digging Holes ....................................................................................... 75
7.4.3 Hole Covers.......................................................................................... 75
7.4.4 Setting Poles ......................................................................................... 76
7.4.4.1 Pike Pole Method.................................................................................. 76
7.4.4.2 Winch Line Method .............................................................................. 77
7.4.4.3 Gin Pole Method................................................................................... 78
7.4.4.4 Pole Setting Truck Precautions ............................................................. 78
7.4.4.5 Energized Line Precautions ................................................................... 78
7.4.4.6 Backfilling Around Poles ...................................................................... 79
7.5 Dismantling Poles.................................................................................. 79
7.5.1 Minimum Pole Support ......................................................................... 79
7.5.2 Additional Pole Support........................................................................ 79
7.5.3 Truck Restraining.................................................................................. 79
7.5.4 Pole Removal........................................................................................ 80
7.6 Climbing and Working on Poles ............................................................ 80
7.6.1 Before Climbing Precautions ................................................................. 80
7.6.2 Type of Pole ......................................................................................... 81
7.7 Pole Climbing Equipment...................................................................... 81
7.7.1 Climbing Safety Equipment ................................................................... 82
7.7.2 Wood-Pole Climbing Equipment ........................................................... 82
7.7.2.1 Climber Requirements ........................................................................... 83
7.7.2.2 Climber Defects .................................................................................... 83
viii
MIL-HDBK-1025/10
PAGE
7.7.2.3 Leather Treatment................................................................................. 83
7.7.2.4 Storing Climbing Equipment ................................................................. 84
7.7.2.5 Conditioning Climbing Equipment......................................................... 84
7.7.2.6 Prohibited Climber Wearing Areas ........................................................ 85
7.7.3 Concrete/Steel Pole Climbing................................................................ 85
7.7.3.1 Fall Arresting Device Considerations..................................................... 85
7.7.3.2 Fall Arresting Anchor Point................................................................... 85
7.7.3.3 Fall Arresting System Provisions ........................................................... 86
7.7.3.4 Climbers’ Tools..................................................................................... 86
7.8 Pole Climbing and Work Precautions .................................................... 86
7.8.1 More Than One Climber........................................................................ 86
7.8.2 Wood-Pole Climbing Precautions.......................................................... 86
7.8.3 Concrete/Steel Pole or Tower Climbing Precautions.............................. 87
7.8.4 General Pole Climbing Precautions........................................................ 87
7.8.5 Precautions While Working on Poles..................................................... 88
7.8.6 Materials Precautions While Working on Poles...................................... 89
7.9 Crossing Pole Structures ....................................................................... 89
7.9.1 Crossing Open Air Switches on Poles.................................................... 90
7.9.2 Balancing Support on Pole Structures ................................................... 90
7.9.3 Climbing H-frame Pole Structures ......................................................... 90
7.10 Stringing or Removing De-Energized Conductors ................................. 90
7.10.1 Line Work Precautions.......................................................................... 90
7.10.1.1 Adjacent to Energized Lines ................................................................. 90
7.10.1.2 Over, Under, or Across Energized Lines ............................................... 91
7.10.2 Other Work Precautions Affecting Aerial Lines ..................................... 91
7.10.2.1 Fallen Wires .......................................................................................... 91
7.10.2.2 Fire ....................................................................................................... 91
7.10.2.3 Vehicular Protection ............................................................................. 91
7.10.3 De-Energized Line Grounding............................................................... 91
7.10.3.1 Permanent Ground Wires ...................................................................... 91
7.10.3.2 Common Neutral Systems ..................................................................... 92
7.10.3.3 Protective Grounding Equipment .......................................................... 92
7.10.4 Handling and Stringing Guidance .......................................................... 92
7.10.4.1 Reels..................................................................................................... 92
7.10.4.2 Conductors ........................................................................................... 92
7.10.4.3 Conductor Grounding ........................................................................... 92
7.10.5 Primary Line Installation ....................................................................... 92
7.10.5.1 Stringing Primary Line Wires ................................................................ 93
7.10.5.2 Clipping In or Tieing Primary Line Wires .............................................. 93
7.10.6 Secondary Line Installation ................................................................... 93
ix
MIL-HDBK-1025/10
...................................................................................................... PAGE
7.10.6.1 Stringing Secondary Line Wires ............................................................ 94
7.10.6.2 Protecting Secondary Lines................................................................... 94
7.10.7 Removing Lines .................................................................................... 94
7.10.8 Guying.................................................................................................. 95
7.10.8.1 Guy Installation..................................................................................... 95
7.10.8.2 Removal of Guys .................................................................................. 96
7.10.9 Insulators .............................................................................................. 96
7.11 Street Lighting ...................................................................................... 96
7.11.1 Street Lighting Precautions ................................................................... 96
7.11.2 Multiple Street Lighting Circuits ........................................................... 96
7.11.3 Series Street Lighting Circuits............................................................... 96
7.11.4 Climbing Space ..................................................................................... 97
7.11.5 Time Switches....................................................................................... 97
7.12 Working On or Around Pole-Mounted Equipment ................................ 97
7.12.1 Aerial Surge Arresters........................................................................... 97
7.12.2 Aerial Switches and Fuses ..................................................................... 97
7.12.3 Aerial Capacitors .................................................................................. 97
7.12.4 Aerial Power Transformers and Voltage Regulators .............................. 97
7.12.4.1 Aerial Energized Work.......................................................................... 98
7.12.4.2 Aerial Installation.................................................................................. 98
7.12.4.3 Aerial Connection ................................................................................. 98
7.12.4.4 Aerial Inspection and Maintenance ........................................................ 99
7.12.4.5 Aerial Fusing......................................................................................... 99
7.12.4.6 Aerial Service Connections.................................................................... 99
7.12.4.7 Aerial Testing ..................................................................................... 100
7.13. Tree Trimming and Brush Removal..................................................... 100
7.13.1 Tree Trimming Training Qualifications ................................................ 100
7.13.2 Tree Trimming Public Safety............................................................... 100
7.13.3 Tree Trimming Tool Safety ................................................................. 100
7.13.4 Working On Trees Near Energized Lines ............................................ 101
7.13.5 Climbing and Working On Trees ......................................................... 101
7.13.5.1 Tree Climbers ..................................................................................... 101
7.13.5.2 Tree Work .......................................................................................... 101
7.13.6 Power Trimming Equipment................................................................ 102
7.13.6.1 Operating Power Trimming Equipment ............................................... 102
7.13.6.2 Chain Saws ......................................................................................... 103
7.13.6.3 Right-of-Way Brush Removal ............................................................. 103
x
MIL-HDBK-1025/10
...................................................................................................... PAGE
Section 8 UNDERGROUND CABLES, STRUCTURES, AND
ASSOCIATED ELECTRICAL COMPONENTS
8.1 Underground Work............................................................................. 105
8.2 Underground Work Area Protection.................................................... 105
8.2.1 Underground Work Area Protection Methods ..................................... 105
8.2.2 Impact of Vehicular Traffic Flow ........................................................ 105
8.2.3 Work Space Considerations ................................................................ 105
8.2.4 Barricades and Warning Precautions ................................................... 105
8.2.4.1 Devices ............................................................................................... 106
8.2.4.2 Flagmen .............................................................................................. 106
8.2.4.3 Barriers and Barricade Tape................................................................ 106
8.2.4.4 Caution and Danger Signs ................................................................... 107
8.2.4.5 Manhole Work Areas .......................................................................... 107
8.2.4.6 Excavation, Trenching, and Backfilling................................................ 107
8.2.4.7 Cable Pulling Protection...................................................................... 109
8.3 Existing Obstruction Protection........................................................... 109
8.3.1 Locating Buried Facilities.................................................................... 109
8.3.2 Direct-Burial Electrical Cable Work .................................................... 109
8.3.3 Digging Restriction ............................................................................. 110
8.3.4 Handling Damage To Existing Utility Lines......................................... 110
8.4 Excavation Practices and Procedures for Damage Prevention .............. 111
8.4.1 Preplanning of the Excavation Project ................................................. 111
8.4.2 All Projects Preplanning ...................................................................... 111
8.4.3 Large Project Preplanning ................................................................... 111
8.4.4 On the Job Site Procedures ................................................................. 111
8.4.5 Excavating in Areas of Utility Locations.............................................. 112
8.4.6 Backfilling in Areas of Utility Locations .............................................. 113
8.4.7 If Damage Does Occur to Existing Utilities ......................................... 113
8.4.8 Accountability for Excavator Error ..................................................... 114
8.5 Preparation for Work in Underground Structures ................................ 114
8.5.1 Removing a Manhole Cover ................................................................ 114
8.5.2 Testing Before Entering Underground Structures ................................ 117
8.5.2.1 Hazardous Conditions in Underground Structures ............................... 117
8.5.2.2 Testers for Underground Structures .................................................... 117
8.5.2.3 Elimination of Combustible or Toxic Gases ......................................... 118
8.5.2.4 Structure Condition Change Retesting Requirements........................... 119
8.5.2.5 Emergency Entrance Into Underground Structures.............................. 119
8.5.3 Ventilation of Underground Structures................................................ 119
8.5.3.1 Forced Air .......................................................................................... 119
8.5.3.2 Sail Method ........................................................................................ 119
8.5.3.3 Natural Method................................................................................... 119
xi
MIL-HDBK-1025/10
...................................................................................................... PAGE
8.6 Work Inside Underground Structures.................................................. 120
8.6.1 General Inside Structure Safety ........................................................... 120
8.6.2 Precautions Before De-Energizing Underground Lines........................ 121
8.6.3 De-energizing Underground Cables and Equipment............................. 122
8.6.3.1 Isolation of Underground Lines…..…………………………………….122
8.6.3.2 Underground Cable and Equipment Grounding ................................... 122
8.6.4 Requirements for Working on Underground Cables and Apparatus ..... 122
8.6.4.1 Underground De-energized Work ....................................................... 122
8.6.4.2 Protection Against Energized Parts ..................................................... 122
8.6.4.3 Underground Working Procedures…………………………………….123
8.6.4.4 Grounding Switch Operation............................................................... 123
8.6.5 Cutting of Underground Cables........................................................... 124
8.7 Heating Materials................................................................................ 125
8.7.1 Eliminating Heating Material Hazards ................................................. 125
8.7.2 Heating Materials Work Precautions ................................................... 125
...................................................................................................... PAGE
9.5.2.3 Priorities ............................................................................................. 140
9.5.2.4 Normal Procedures ............................................................................. 143
9.5.2.5 Emergency Procedures........................................................................ 143
9.6 Portable Shore Power Cables and Receptacles..................................... 143
9.6.1 Low-Voltage (480-Volt) Power Cable Specification............................ 143
9.6.2 Medium-Voltage (4,160-Volt) Power Cable Specification ................... 144
9.6.3 Power Cable-in-Use Insulation Resistance Values ............................... 144
9.6.3.1 Shore Criteria for Cable Assemblies .................................................... 144
9.6.3.2 Ship Criteria for 480-Volt Service Cable ............................................. 144
9.6.3.3 Explanation of Criteria Differences…………………………………….144
9.6.4 Low-Voltage Receptacles, Plugs, and Protective Circuit Breakers....... 144
9.6.4.1 Shipboard Connection......................................................................... 144
9.6.4.2 Pier Low-Voltage (480-Volt) Electrical Outlet Assemblies.................. 145
9.6.4.3 Low-Voltage (480-Volt) Receptacle Protective Circuit Breakers......... 145
9.6.5 Medium-Voltage (4,160-Volt) Receptacles, Plugs, and Protective
Circuit Breakers ............................................................................... 145
9.6.5.1 Shipboard Connections ....................................................................... 146
9.6.5.2 Pier Medium-Voltage (4,160-Volt) Electrical Outlet Assemblies ......... 146
9.6.5.3 Medium-Voltage (4,160-Volt) Receptacle Protective Circuit
Breakers .......................................................................................... 146
9.7 Ship Connection Procedures Before Ship Docks ................................. 146
9.7.1 Laying, Inspecting, and Testing Power Cable Assemblies .................... 147
9.7.1.1 Laying Power Cable Assemblies .......................................................... 147
9.7.1.2 Moving Power Cable Assemblies on Pier............................................. 147
9.7.1.3 Inspecting and Testing Power Cable Assemblies.................................. 148
9.7.2 Checking Shore Receptacles................................................................ 149
9.7.2.1 Inserting Cable Plugs Into Receptacles ................................................ 150
9.8 Shore-to-Ship Power Cable Rigging After Ship Docks ........................ 151
9.9 Ship's Transfer to Shore Power ........................................................... 151
9.10 Ship's Transfer Back to the Ship's Generator ....................................... 151
9.11 Shores Disconnection of Cable Plugs and Removal of Cable
Assemblies ........................................................................................ 152
FIGURES
xiii
MIL-HDBK-1025/10
PAGE
6 Insulated and Uninsulated Aerial Lift Vehicle Grounding Connections... 39
7 Using a Conductive or Insulating Platform for Opening/Closing
De-Energized Overhead Conductors .................................................. 41
8 Composite Stringing/Removing the Temporary Protective Grounds on
Overhead Conductor Lines.................................................................. 42
9 Pike Pole Method.................................................................................. 76
10 Winch Line Method .............................................................................. 77
11 Steps in Removing a Manhole Cover................................................... 115
12 Sail Method of Manhole Ventilation.................................................... 120
13 Shore-to-Ship Portable Power Cable Location Diagram ...................... 134
14 Preferred Ship-to-Shore Circuit Arrangement...................................... 135
15 Procedures in Safely Energizing a Ship From a Shore Electrical
Circuit............................................................................................... 136
16 Low-Voltage (480-Volt) Shore Receptacle ......................................... 145
17 Medium-Voltage Shore Receptacle ..................................................... 146
TABLES
xiv
MIL-HDBK-1025/10
PAGE
23 Temporary Ground Rod Minimum Requirements .................................. 35
24 Substation Protective Grounding Procedure .......................................... 37
25 Grounding of Substation Equipment...................................................... 38
26 Grounding of Equipment During Oil Handling....................................... 39
27 Procedures for Grounding Insulated and Uninsulated Aerial Lift
Trucks ............................................................................................... 40
28 Stringing/Removing Conductor Ground Locations ................................ 41
29 Conductor Ground Location After Pulling............................................. 42
30 Categories of Electrical Line Maintenance Work ................................... 43
31 Approved Energized Work Methods by Voltage Class .......................... 44
32 Insulating Tools for Electrical Workers ................................................. 45
33 Common Classification for Plastic Guards ............................................. 45
34 Insulating Plastic Guards/Platforms for Electrical Workers .................... 46
35 Prework Procedures.............................................................................. 46
36 Energized Work Precautions ................................................................. 47
37 Voltage Level Work Procedures............................................................ 47
38 Average Size of Crew Required to Raise Poles of Different Lengths
by Piking........................................................................................... 77
39 Shore-to-Ship Electrical Connect Responsibilities................................ 127
40 Shore-to-Ship Electrical Disconnect Responsibilities ........................... 127
PICTURES PAGE
INDEX ………………………………………………………………………………..153
xv
MIL-HDBK-1025/10
xvi
MIL-HDBK-1025/10
Section 1. INTRODUCTION
1.3 Handbook Presentation. This handbook presents safety concerns in two ways.
1.3.1 Tabular Method. Worker concerns dealing with safe and unsafe practices both
to general hazards and electrical hazards applying to de-energized and energized line work are
considered best covered by summarizing them as tabular lists or rules. The tables remind the
worker of general actions that apply to the normal conduct of electrical service work and are
intended to indicate necessary instructions in a simplified manner or standard operating
procedures (SOP’s).
1.3.2 Nontabular Method. Worker concerns dealing with safe and unsafe practices on
the specific hazards applying to the type and location of equipment and lines (such as substations
and aerial and underground systems) are considered best covered by providing expanded
instructions. Instructions are intended to clarify facilities SOP’s or to provide a basis for
generating a job hazard analysis (JHA).
WARNING
CAUTION
Note
1
MIL-HDBK-1025/10
1.4.1 Applicable Documents. Section 2 lists the documents that form a part of this
handbook to the extent referenced.
1.4.2 Definitions. Section 3 lists abbreviations and acronyms used in this handbook.
1.4.3 General Safety Practices. Section 4 covers general safety observances and
hazards associated with electrical work.
1.4.5 Substations and Switchgear. Section 6 covers the specifics for equipment
found or used in substations including medium-voltage switchgear.
1.4.6 Overhead Lines and Associated Electrical Components. Section 7 covers the
specifics for poles and structures and the aerial lines they support along with their necessary pole-
mounted equipment. Such specifics cover pole handling and erection, climbing and working on
poles, stringing of lines, working requirements around pole-mounted lighting, equipment and tool
handling, and tree and brush trimming required for foliage that impinges upon aerial line right-of-
ways.
2
MIL-HDBK-1025/10
2.1 General. The documents listed below are not necessarily all of the documents
referenced herein, but are the ones that are needed to fully understand the information provided
by this handbook. Other documents have the titles listed after their reference and if they are listed
more than once are included in the listing below.
3
MIL-HDBK-1025/10
4
MIL-HDBK-1025/10
Section 3. DEFINITIONS
h. dc - Direct Current
i. EO - Electrical Officer
k. ES - Electrical Supervisor
m. ft - Feet
n. Hz - Hertz
p. In. - Inch
r. kV - Kilovolts
u. LTC - Load-Tap-Changing
5
MIL-HDBK-1025/10
v. m - Meter
jj. V – Volts
3.2 Definitions. Definitions for terms used in this handbook are contained in
IEEE 1000, The IEEE Standard Dictionary of Electrical and Electronics Terms.
6
MIL-HDBK-1025/10
4.1.1 Use. Use the information to remind you of the safety requirements of the
Occupational Safety and Health Administration (OSHA), NAVFAC 5100.11, NAVFACENCOM
Safety and Health Program, OPNAVINST 5100.23, Navy Occupational Safety and Health
(NAVOSH) Program Manual, and OPNAVINST 5100.24, Navy System Safety Program. Also
refer to OPNAV 11310.3, Operation and Maintenance of Shore-to-Ship Power and NAVFAC
11300.37A, Energy and Utility Policy Manual.
4.1.2 Construction. All Naval activities are required to comply with the latest OSHA
standards of 29 CFR 1926, Subpart V, Power Transmission and Distribution.
4.1.4 Application. In following the safety precautions of this handbook and of OSHA
or other references herein, the most stringent requirement will apply.
4.1.5 Unique Requirements. All workers qualified to provide shore power to Navy
ships are required to comply with shore-to-ship safety requirements. Ship’s services are
ungrounded systems that meet the design requirements of OSHA standard 29 CFR 1910.304
Design Safety Standards for Electrical Systems.
4.2 Job Hazards. Awareness of job hazards is the key to mishap prevention.
4.2.1 Accessibility. The more accessible and protected the work area the less hazards
that will confront the worker. Where access items are required comply with OSHA standard 29
CFR 1910.269(h), Ladders, Platforms, Step Bolts, and Manhole Steps.
4.2.1.1 Inside Work. Inside work may require special protective apparel, especially if
hazardous substances are present. Ladders or scaffolds may be used and workers should then
conform to applicable elevated position work requirements.
4.2.1.2 At Grade Work. At grade work may require protection from the weather and
also work area protection from the public if not suitably fenced or otherwise guarded.
7
MIL-HDBK-1025/10
4.2.1.3 Aerial Work. Aerial work may be on poles, trees, or aerial lift bucket trucks.
4.2.2 Work Area Protection. Improper work area set up, that is, poor signs, traffic
control or security could result in an accident. Vehicle operators should watch out for obstacles
such as a high-voltage pole and also for pedestrians. Activity regulations, federal regulations and
safe working procedures should be followed. Planning should be tailored to the work site.
Adequate barriers, warning signs, traffic cones, and lights, should be located on approaches to and
at the work areas, excavations, open manholes, parked equipment, and other hazards. Flagmen
are necessary if there is any doubt that the warning devices are not adequate as controls.
4.2.3 Normal Environmental Impacts. Potential mishaps can result from the
environment where the work is to be done.
4.2.3.3 Noise Control. Protection against the effects of noise exposure should be
provided for facility workers whenever the sound level equals or exceeds 85 dB(A) decibels
adjusted continuous level pressure or 140 decibels peak sound level pressure for impulse or
impact noise, regardless of the duration of exposure.
4.2.3.4 Lighting. Safety requires adequate illumination of the working area. Where
natural or installed artificial illumination is not sufficient, then temporary lighting should be
provided. The use of matches or open flames to provide such illumination is forbidden.
8
MIL-HDBK-1025/10
a. Bodily harm can result from contact with asbestos, polychlorinated biphenyls (PCB),
and sulfur hexafluoride (SF6). All are classified as hazardous substances and should be
treated in accordance with Environmental Protection Agency (EPA) regulations.
4.2.4.1 Asbestos. Asbestos is no longer being installed for insulation or fire protection
purposes or used as a conduit or piping material. Cutting existing asbestos materials can release
asbestos fibers to the atmosphere. If fibers are suspended in the air in significant quantities,
respiratory harm may be caused by their inhalation.
Note: Employees who are not qualified to work with asbestos are not to handle or remove
materials containing asbestos fibers. Refer to 29 CFR 1015.1001(Asbestos) for worker
qualifications and requirements for handling asbestos containing materials.
4.2.4.3 Sulfur Hexafluoride (SF6). In its pure state, SF6 is a colorless, odorless,
tasteless, nonflammable, nontoxic, and noncorrosive gas shipped in a liquid form. Since it is five
times heavier than air it can act as an asphyxiant and in a liquid state it can cause tissue freezing
similar to frost bite. Its decomposition products, which can result from electric arcs or faults, are
toxic.
combustion engine exhausts. Hydrogen chloride can result from faults or fires involving polyvinyl
chloride (PVC) conduits or PCB oils. Adequate oxygen may be unavailable when the atmosphere
is displaced by heavier-than-air gases.
4.3 Reminder of Electrical Hazards in the Field. Always identify the electrical
hazards applying to the work being done. Rules, apparel, tools, and tests, if correctly used, will
protect you from the destructive effects of electric shocks, arcs, and blasts and the hazards of
elevated and confined workplaces.
4.3.1 Dangers From Electric Shock. Electric shock results from setting up an electric
current path within the human body. The current flows because there is a potential gradient
(voltage difference) between an energized object and the grounded worker. Figure 1 shows
potential gradients and the safe area or equipotential zone, which has no potential gradient.
Figure 2 indicates current flow paths. Table 1 indicates the effects of 60-hertz current on humans.
Figure 1 Figure 2
Ground Potential Gradient Current Path Flow
10
MIL-HDBK-1025/10
Table 1
Effects of 60-Hertz Current on Humans
Milliamperes
Effect
Men Women1
Slight sensation on hand 0.4 0.3
Perception threshold 1.1 0.7
Shock, not painful and muscular control not lost 1.8 1.2
Painful shock, painful but muscular control not lost 9 6
Painful and severe shock, muscular contractions, breathing 23 15
difficult
Ventricular fibrillation, threshold 75 75
Ventricular fibrillation, fatal (usually fatal for shock 235 235
duration of 5 seconds or longer)
Heart paralysis (no ventricular fibrillation), threshold 4,000 4,000
(usually not fatal; heart often restarts after short shocks)
Tissue burning (usually not fatal unless vital organs 5,000 5,000
damaged)
1
The current values for women are lower because women typically have less body mass
than men.
4.3.2 Danger From Arcs and Blasts. Arcs result from the passage of electric current
through air. The air fails as an insulator but serves as a conducting medium for ionized gases.
Blasts result when the metal at the arc site expands and vaporizes. Arcs can reach temperatures
up to four times the temperature of the sun’s surface. Water expands 1,670 times when it
becomes steam; copper expands 67,000 times when it vaporizes. High-energy arcs can be fatal
even at distances of 3 meters (10 feet).
4.4.1 General Body Protection. Always wear personal protective clothing as required
by your supervisor and as appropriate to the work area, work methods, and site hazards. Wear
these items because it is impossible or impractical to totally eliminate all work site hazards and
they will reduce your chance of injury or illness. OSHA standard 29 CFR 1926 Subpart E,
Personal Protective and Life-Saving Equipment covers this protection and indicates where it is
required. An example is where confined spaces or hazardous gases mandate respirators. A
summary of apparel requirements for general body protection is given in Table 2.
11
MIL-HDBK-1025/10
Table 2
Apparel and Body Protection Requirements
I. Clothing:
A. Around nonelectrical industrial activities wear full length work pants and shirts
with at least short sleeves.
B. Around machinery you may not wear or have dangling sleeves, neckties, or
unsecured long hair.
C. Around vehicular traffic or on the flightline wear safety color fluorescent
clothing with approximately 0.33 square meters (3.5 square feet) of reflective
area above the waste.
D. On or near energized lines/equipment wear long-sleeved apparel with no
acetate, nylon, polyester, or rayon alone or in blends; no metallic items
(fasteners); no jewelry items; and no celluloid items. Flame-resistant clothing is
required where arc blast hazards are identified. See Table 11.
12
MIL-HDBK-1025/10
Table 2 (Continued)
Apparel and Body Protection Requirements
II. Head Areas
A. Wear an ANSI Z89.1, Protective Headwear for Industrial Workers type B or
type E hard hat that has a rating of 20,000 volts, 60 hertz for 3 minutes,
provides a suspension to 38 millimeters (1.5 inches) above the head, and can
include an optional cold weather liner and chin strap. Wear where exposed to
energized lines/equipment and falling objects such as exterior substations,
overhead and underground lines, construction sites, fuse changing, voltage
readings, and maintenance of batteries and medium-voltage equipment.
B. Wear ANSI Z87.1, Occupational and Educational Eye and Face Protection eye
and face protection with impact-resistant lenses and side shields. Contact
lenses do not provide eye protection. Face shields do not provide impact eye
protection. Filter lenses are required for radiant energy protection.
C. Use ear plugs or inserts in ear canals that provide 25 to 30 decibel attenuation
or ear caps and muffs or muffs that go over ear canals and provide 22 to 27
decibel attenuation. A combination of both can provide 35 to 37 decibel
attenuation. All need careful fitting.
D. Respiratory protection needs to be provided per the confined space entry plan
and/or the hazardous material regulated area requirement. Use NIOSH
certified device if the hazard type has a NIOSH performance requirement. Use
for emergencies only; correct hazardous atmospheric conditions with
ventilation. Requires special training and fitting.
III. Other Body Areas
A. Apply appropriate protective ointment to skin if needed for exposed areas.
Ointment should not be damaging to rubber goods.
B. Use rubber gloves where required in other chapters of this handbook. Use
leather palm gloves for protection when rubber gloves are not required. Use
welders’ gloves when welding.
C. Wear ANSI Z41, Protective Footwear, P591, C75 or I75 shoes rated for 34
kilograms (75 pounds) crushing strength and having no heel or toe plates or
hobnails. Use electrically insulated shoes for de-energized line work within 3
meters (10 feet) of grounded items. Use conductive shoes where needed for
protection from static discharges.
13
MIL-HDBK-1025/10
4.4.2 Safety Equipment and Tools. When working around electrical lines and
equipment, temporary protective insulation is provided by using the insulating properties of
rubber goods, plastic guard equipment, and live-line tools. Platforms and aerial lift bucket trucks
provide insulated supports for positioning a worker.
Table 3
ASTM F 18 Rubber Goods1
Maximum use, Proof test Minimum distance2
Class Color label
ac volts ac volts millimeters (inches)
1,000 0 Red 5,000 25 (1)
7,500 1 White 10,000 25 (1)
17,000 2 Yellow 20,000 50 (2)
26,500 3 Green 30,000 75 (3)
36,000 4 Orange 40,000 4 (100)
1
Wear leather protectors over rubber gloves.
2
Minimum length of exposed rubber glove above the leather protector.
4.4.2.2 Plastic Guard Equipment. This equipment is rated for momentary (brush)
contact protection. Guards include those installed on conductors; connecting covers used over
lines, insulators, buses, and structures; and apparatus guards used over poles, crossarms, cutouts,
and switchblades. See Tables 33 and 34 in section 5. Electrically retest plastic guard equipment
based on work practice and test experience. Electrically retest items where there may be a reason
to suspect the electrical integrity of the equipment.
4.4.2.3 Live-Line Tools. Comply with the requirements of OSHA standard 29 CFR
1910.269(j), Live-Line Tools. ANSI/IEEE 935, Guide on Terminology for Tools and Equipment
14
MIL-HDBK-1025/10
to be Used in Live-Line Working covers the live-line tools used to hold, move, operate, and test
equipment. Tools are only as safe as their continued care and inspection make them. Try to
always use a fiberglass tool as it is impervious to oil-borne materials and solvents, is stronger, and
is a better insulator than wood. Live-line tools should be wiped clean and visually inspected
before use each day. Do not use tools in rain or heavy fog, except in an emergency where
directed by your foreman/lead electrician. In any case, never use tools when weather conditions
allow formation of rivulets of water along the tool. Hang tools on hand lines or approved tool
hangers, never on conductors or ground (bond) wires.
4.6 Worker/Crew Responsibilities. All personnel are responsible for safety at all
times, for prompt mishap handling, and conducting before each job a program in accordance with
OSHA standard 29 CFR 1910.269(c), Job Briefing.
4.6.2.1 Qualified Workers. Persons who by training and demonstration are familiar with
the skills and techniques for: (1) distinguishing exposed live parts from other parts of electric
equipment; (2) determining the nominal voltage of exposed live parts; and (3) maintaining
minimum clearance distances corresponding to the voltages to which that person will be exposed.
4.6.2.2 Unqualified Workers. Persons not meeting the requirements for Qualified
Worker. However, to be on the job these persons should be trained in all electrically related
practices that are necessary for their safety.
15
MIL-HDBK-1025/10
Table 4
General Safety Observances
4.6.3 Mishap Handling. Each worker should know what to do when a mishap occurs.
Additionally, each worker should know how to report injuries and other mishaps.
4.6.3.1 Knowing What to Do. Table 7 summarizes the first aid knowledge required of
each worker. As a preplanning aid, an emergency telephone number list should be prepared to
include the location and telephone numbers of the nearest ambulance or emergency medical
treatment responders, the nearest hospital with an emergency room, the nearest helicopter
evacuation service, and the nearest burn trauma center.
16
MIL-HDBK-1025/10
Table 5
Significant Unsafe Actions and Conditions
I. Unsafe actions
A. Operating without authority; failure to secure or warn others
B. Operating or working at unsafe speeds
C. Making safety devices inoperative without proper authorization
D. Using unsafe equipment (hands instead of equipment) or equipment unsafely
E. Taking unsafe positions or postures
F. Working on moving or dangerous equipment
G. Distracting, teasing, abusing, startling
H. Failing to use safe attire or personal protective devices
I. Failing to lock-out energized circuits
II. Unsafe conditions
A. Improperly guarded facilities
B. Defects of facilities
C. Hazardous arrangement or procedure
D. Improper ventilation
E. Improper illumination
F. Unsafe dress or apparel
Table 6
Levels of Safety Accountability
Title Electric safety accountability
17
MIL-HDBK-1025/10
Table 7
Knowing What To Do
4.6.3.2 Work Injuries and Mishap Reports. Report injuries, even minor ones, to your
immediate supervisor in accordance with OPNAVINST 5100.23. Additionally, every mishap
involving personnel injury, property damage, or near misses should be investigated to determine
the cause and the corrective action needed to prevent recurrence. Base safety personnel conduct
investigations. Local safety staff should be notified of all mishaps that involve personnel injuries
or property damage. Mishaps should be investigated and reported through safety channels.
4.6.3.3 Rescue Operations. Rescue operations will vary with the individual situation. A
good rule of thumb is never to touch any live parts or any person in contact with live parts
without using an insulating medium. Always wear personal protective equipment. Before
rendering any assistance, the rescuer should make an emergency call to the dispatcher on the two-
way radio or the nearest telephone. He/she should quickly pinpoint the location of the mishap,
describe the problem, and the assistance required.
18
MIL-HDBK-1025/10
Table 8
Lockout/Tagout/Tryout Control Program Development
I. Equipment
A. Employ additional means to ensure safety when tags rather than locks are used by
instituting an effective program.
B. Ensure that new or overhauled equipment can be locked.
C. Obtain standardized locks and tags that indicate the identity of the employee
using them, and which are of sufficient quality and durability to ensure their
effectiveness.
II. Procedures
A. Identify and implement specific procedures (generally in writing) for the control
of hazardous energy including preparations for shutdown, equipment isolation,
lockout/tagout/tryout application, release of stored energy, and verification of
isolation.
B. Institute procedures for release of lockout/tagout/tryout including machine
inspection, notification and safe positioning of employees, and removal of the
lockout/tagout/tryout device.
C. Adopt procedures to ensure safety when equipment should be tested during
servicing, when outside contractors are working at the site, when a multiple
lockout/tagout/tryout is needed for a crew servicing equipment, and when shifts
or personnel change.
III. Inspection and training
A. Conduct inspections of equipment and lockout/tagout/tryout control procedures
at least annually.
B. Train employees in the specific equipment lockout/tagout/tryout control
procedures with training reminders as part of the annual control inspections.
19
MIL-HDBK-1025/10
work in pairs or a team. Each crewmember should be trained to go to a crewmate’s rescue if the
person appears to need help, providing the helper is not in any danger whatsoever.
4.8.1 Programs. Ensure that all the topics of Table 9 are included in an activities
training program. The use of safety posters, mockups (or actual equipment), pictures, and other
aids are essential in conducting successful safety meetings. Enthusiasm is always desirable.
Training seminars should be held in-house at Public Work Centers (PWCs) or other activity
locations. Supplementary training from commercial sources such as that by equipment
manufacturer or by training institutes should be scheduled as required.
20
MIL-HDBK-1025/10
Table 9
Required Training
21
MIL-HDBK-1025/10
Table 10
SOP/JHA Procedures
I. General
A. Description of work to be done.
B. Specific hazards and how to minimize or eliminate them by use of specific
safety equipment.
C. Instructions covering special working area practices on grounding,
unusual equipment or tools, and any particular first aid requirements for
hazardous materials.
D. Sequence of major steps or a detailed step-by-step work listing.
II. Specifics (if not included above)
A. Work location.
B. Nominal line voltages.
C. Maximum switching transient voltages.
D. Possible hazardous induced voltages.
E. Condition of protective grounds and equipment grounding conductors.
F. Conditions of environment relative to safety (poles, traffic, need for
additional protective equipment such as fall protection or flotation
devices).
G. Locations of other lines including communication and fire protective
signaling circuits not involved in the work.
22
MIL-HDBK-1025/10
WARNING
23
MIL-HDBK-1025/10
Table 11A
Limits of Approach
24
MIL-HDBK-1025/10
Table 11B
Qualified Worker Minimum Working Distances
1 2 3 4 5 6
Table 12
Unqualified Worker Minimum Approach Distances
Voltage to ground Distance
50 kV or below 3 m (10 ft)
5.1.2 Work Methods in Relation to Worker’s Safety. All work will be done
de-energized unless energized line work has been specifically authorized.
25
MIL-HDBK-1025/10
Table 13
Jobs Requiring Two Electrical Workers
Hazard exposure Working on
I. Energized lines
Installation, removal, or II. De-energized lines with possible energized parts contact
repair when working on or III. Equipment with possible energized line contact
near lines or parts energized
at more than 600 volts ac or IV.Mechanical equipment operation (except insulated aerial
250 volts dc lifts) near energized parts
V. Other work with equal or greater hazard exposure
Table 14
Jobs Working in Confined Spaces
Requiring Additional Workers
26
MIL-HDBK-1025/10
Table 15
Jobs Generally Acceptable for One Electrical Worker
I. Work on de-energized systems with nominal system voltages of 600 volts ac or 250 volts
dc, or less.
II. Routine electrical measurements on energized systems with nominal system voltages of 600
volts ac or 250 volts dc, or less.
III. Routine operation of metal-enclosed switchgear with nominal system voltages of 600 volts
ac or 250 volts dc, or less.
IV.Routine electrical measurements or switching using gloves and live-line tools if the worker
is positioned out of reach or possible contact with energized parts.
V. Emergency repair work to safeguard the general public, if previously authorized.
Note
WARNING
27
MIL-HDBK-1025/10
5.1.4.2 Phasing Testers. Phasing testers are used to determine the phase
relationship of energized lines. Short circuits occur when different phases are tied
together. A phasing tester can use two high-resistance units on hot sticks connected by a
phasing-out voltmeter. Where voltage transformers are available, a voltmeter can be
connected between one side to the other side. If lines are in phase, the voltmeter will
register zero. If performing a phasing check at a generator disconnect, the maximum
voltage rating of the phasing tester should be at least two times the nominal rated voltage
of the circuit to be tested.
28
MIL-HDBK-1025/10
5.2.2 Safety Basics. The basics of safety for every outage consists of the
lockout/tagout/tryout procedures that can be simplified as providing a recognition of
energy hazards, a sequence of lockout/tagout/tryout steps for every energy hazard and
correctly locking and tagging the necessary devices.
Table 16
Switching Order Outage Package Documents
I. Request for utility interruption.
II. PWC/EFD scheduled interruption of utility services notice
III. Notes concerning the outage
IV. Switch out switching orders
V. Switch back switching orders
VI. Lockout/tagout/tryout fact sheet
VII. Distribution one-line diagrams
VIII. Outage safety briefing memo
IX. Switch operator briefing memo
X. Clearance notice
WARNING
29
MIL-HDBK-1025/10
Table 17
Hazardous Energy Control
I. Electrical systems/equipment
A. Isolating by control operation such as open switching devices; lockout/tagout/tryout if
possible; pull plugs or fuses; block interlock feedbacks.
B. Stored energy release such as disconnect and discharge capacitors, choke coils, and
surge arresters; discharge static electricity; temporarily short to ground induced voltage
from adjacent lines, static charges, accidental connections, and incorrect disconnections;
provide shielding for possible contact with energized parts
C. Verify by testing there is no voltage on de-energized system/equipment.
II. Nonelectric energy hazards
A. Check for chemical, electromagnetic, mechanical, pneumatic, thermal, and ultraviolet
energy.
B. Isolate by blocking valve operations or other control operations for the above systems.
C. Discharge trapped energy by releasing pressure or by draining/purging lines and verify
lack of rotation or dangerous temperatures.
WARNING
Table 18
Sequence of Lockout/Tagout/Tryout Steps
I. De-energizing steps
A. Notify all affected workers of hazards, their control, and any possible stored energy.
B. Shut down the system by isolation of energy sources. System is rendered inoperative.
C. Secure all energy source shutdowns by lockout/tagout/tryout of controls.
D. Release all stored energy and verify such release.
E. Verify by testing there is no voltage.
F. Provide temporary grounding (refer to par. 5.3).
30
MIL-HDBK-1025/10
Table 18 (Continued)
Sequence of Lockout/Tagout/Tryout Steps
Table 19
Tag Requirements
Color Warning Use for Do not use for
31
MIL-HDBK-1025/10
electrical system to meet safety and design requirements. A ground system consists of a
grounding connection, a grounding conductor, a grounding electrode, and the earth (soil)
that surrounds the electrode or some conductive body which serves instead of the earth
(an airplane’s frame). A jumper connects conductors so that continuity is maintained.
Bonding is the joining of metallic parts to form a conductive path. Temporary grounds are
used so that work may be safely done on parts of the system that are temporarily isolated
and cleared (de-energized). To be safe when working on a de-energized circuit it should
always be de-energized, tested dead; isolated, tested dead; locked out and tagged; and
grounded.
Table 20
Causes of Hazardous Induced Potential Differences
I. Potential differences caused by various line effects (such as induced voltages from adjacent
energized lines and electrostatic build-up from wind action).
II. Lightning strikes anywhere in the circuit.
III. Fault-current feed-over from adjacent energized lines.
IV. Connection to an energized source through switching equipment, either by equipment
malfunction or human error.
V. Accidental contact of the de-energized line with adjacent energized lines.
VI. Residual charge from power-factor correction capacitors or surge arresters.
32
MIL-HDBK-1025/10
WARNING
Table 21
Temporary Grounding Connection/Removal Procedures
Never approach closer than working distances given in Table 11 until after
the line/equipment has been isolated, de-energized, tested, and properly
grounded. Afterwards, avoid coming closer than 3 meters (10 feet) to
minimize the hazard from step and touch potentials. This minimizes step
and touch potential differences.
5.3.3.2 Potential Differences. Such potential differences occur from items such
as down guys, ground rods, maintenance vehicles, and structure legs or ground wires
33
MIL-HDBK-1025/10
during the period in which they are bonded to temporary grounds. When it is absolutely
necessary to work on or near these features, workers should use bonded conductive or
insulated platforms, or approved insulated shoes to minimize the hazard from step and
touch potentials. Bond separately grounded systems together if they can be
simultaneously contacted.
5.3.4.1 Grounding Clamps. Use the alloy (copper or aluminum) matching the
conductor or device to which it is attached and meeting or exceeding the current-carrying
capacity of the associated cable. Use smooth jaw clamps on buses to avoid surface
marring. Use serrated clamp jaws to bite through corrosion products for attachment to
conductors or metal products. Self-cleaning jaws are recommended for use on aluminum.
Never use hot-line clamps for grounding.
a. Derate these fault current by 10 percent when using multiple ground cables
(which should all be of the same size and length).
d. Avoid very low temperatures; the clear jacket which allows checking for strand
breakage will stiffen at low temperatures and split or shatter.
34
MIL-HDBK-1025/10
Table 22
Maximum Fault Current Capability for Grounding Cables1
Cable size Fault time Root-mean-square amperes
(AWG) (cycles) (copper)
15 27,000
2/0
30 20,000
15 36,000
3/0
30 25,000
15 43,000
4/0
30 30,000
1
These current values are the “withstand rating” currents for grounding cables and cables as
per ASTM F 855. These values are about 70 percent of the fusing (melting) currents for
new copper conductors. They represent a current that a cable should be capable of
conducting without being damaged sufficiently to prevent reuse.
5.3.4.3 Grounding Ferrules. Use ASTM F 855, Type IV (threaded stud copper
base compression type) when installed on grounding cables by facility personnel. Ferrules
should have the filler compound vent hole at the bottom of the cable so that workers can
visually check that the cable is fully inserted into the ferrule. Heat shrink or springs should
be installed over a portion of the ferrule to minimize strand breakage caused by bending.
In all cases, the manufacturer’s recommendations should be followed. Do not use
aluminum alloy ferrules as they will not provide a lasting snug fit. Check for tightness
periodically.
5.3.4.4 Grounding Cluster Bars. Use to connect phase and neutral conductor
jumper cables to the selected method of providing a ground electrode (pole ground wire,
temporary ground rods, substation ground grid). Cluster bars should have an attached
bonding lead. Provide temporary ground rods as given in Table 23.
Table 23
Temporary Ground Rod Minimum Requirements
I. Single rod installed to a depth of 1.5 meters (5 feet) below grade.
A. A minimum 16-millimeter (5/8-inch) diameter bronze, copper, or copper-weld rod at
least 1.8 meters (6 feet) long.
B. A 1.8-meter (6-foot) long, screw-type ground rod, consisting of a minimum 16-
millimeter (5/8-inch) diameter copper-weld shaft with a bronze auger bit and bronze
T-handle, tightly connected to the rod.
II. Additional rods to provide additional 1.5 meters (5 feet) lengths below grade where
required.
A. Install 1.8 to 2.4 meters (6 to 8 feet) apart while maintaining the 3-meter (10-foot) step
and touch potential clearance.
B. Bond all rods together prior to installing other electrode connections.
35
MIL-HDBK-1025/10
Figure 3 Figure 4
Correct Single-Point Ground Incorrect Multi-Point Ground
36
MIL-HDBK-1025/10
D2 D1
Nonconductive ladder
Figure 5
Substation Temporary Grounding
Table 24
Substation Protective Grounding Procedures
37
MIL-HDBK-1025/10
Table 25
Grounding of Substation Equipment
I. Tanks. Grounds should be in place (see Table 26) before a tank is opened and the
insulating medium (oil/gas) is changed. This does not apply to sampling.
II. Ground switches. No type of switch may be used to maintain personal ground continuity.
III. Capacitors.
A. Allow at least 5 minutes between opening of the capacitor switching devices and the
closing of the ground switch on a fully charged capacitor bank.
B. Allow at least 5 minutes after the ground switch is closed before installing protective
grounds.
C. A capacitor bank should remain de-energized for at least 5 minutes before it is re-
energized.
D. The time required for these maneuvers should be explicitly expressed in switching
orders involving capacitor banks.
IV. Surge arresters. Surge arresters should be disconnected and discharged using grounding
cables.
V. Grounding transformers. Grounding transformers should not be worked on unless de-
energized and properly grounded. Phase reactors should be isolated from all energized
sources and grounded before being worked on.
VI. Bushings.
A. Bushing leads may be disconnected from bushing terminals as necessary to permit
equipment testing that requires the equipment to be ungrounded.
B. Use a hot stick to connect test equipment and re-establish the ground as soon as the
test is completed.
C. Following an applied potential test (“Hi-Pot”), ensure the ground remains in place for a
period at least two times the duration of the test period.
D. Work clearances and grounding instructions for the test equipment will be in
accordance with the manufacturer’s recommendations.
VII. Separate grounds. Install separate grounds for each isolated section of the de-energized
circuit if a hazard exists when working in a de-energized area of a substation where there is
one or more physical breaks in the electrical circuit.
38
MIL-HDBK-1025/10
Table 26
Grounding of Equipment During Oil Handling
I. Oil system.
A. Bond apparatus tanks, conductive hoses, pumping or filtering equipment, drums, tank
cars, trucks, and portable storage tanks to the station ground mat.
B. Connect the supply end first and disconnect it last to prevent possible arcs near the
source such as oil trunks, tank cars.
II. Equipment conductors. Bond exposed conductors, such as transformer or circuit
breaker bushings, or coil ends or transformers where bushings have been physically
removed, to the same grounding point.
WARNING
39
MIL-HDBK-1025/10
Table 27
Procedures for Grounding Insulated and Uninsulated Aerial Lift Trucks
40
MIL-HDBK-1025/10
1 Three-phase ground all conductors and 3 Ground conductive platform but not
structure on one side of the work. insulating platform.
4
No 3 here
1 2 1
2
Metallic 4
3
Table 28
Stringing/Removing Conductor Ground Locations
I. General.
A. Ground all stringing equipment such as reel stands, pullers, tensioners, and other
devices.
B. Provide a safety barrier around the equipment.
II. Running ground. Install a running ground between pulling and tensioning equipment and
their adjacent structures.
III. Stringing blocks.
A. Ground stringing blocks at first and last structures, and at least every 3.2 kilometers(2
miles) in between.
B. Ground stringing blocks at each structure on both sides of an energized circuit being
crossed.
C. If the design of the circuit interrupting devices protecting the lines so permits, the
automated reclosing feature of those devices should be made inoperative.
41
MIL-HDBK-1025/10
Tensioner 4
4 4
5 3
5 1
3
2 2
2 3.2 kilometers (2 miles)
Reel Maximum
Figure 8
Composite Stringing/Removing the Temporary Protective Grounds on
Overhead Conductor Lines
Table 29
Conductor Ground Location After Pulling
I. Structure grounds
A. Ground at each structure next to intermediate deadends of the stringing operation.
B. Ground at each structure where and while work (including clipping-in) is being
performed on or near the conductor.
II. Removal. Remove grounds as the last phase of finished aerial installation.
42
MIL-HDBK-1025/10
WARNING
WARNING
Table 30
Categories of Electrical Line Maintenance Work
Line potential1 Worker insulation Worker protective methods Approved for use
Ground None De-energize, isolate, Always
lockout/tagout/tryout, and
ground2
Intermediate Isolated from Use insulated aerial lifts/supports Requires specific
grounded objects by and insulated tools on energized approval
insulating means lines
Line Insulated from ground Bonded to energized line for Prohibited
barehand work
1
Refer to ANSI/IEEE 516, IEEE Guide for Maintenance Methods on Energized Pole-Lines for
definitions.
2
When lines are not grounded they are considered energized.
WARNING
43
MIL-HDBK-1025/10
Table 31
Approved Energized Work Methods by Voltage Class1
Nominal ac voltage level Work method
Up to 600 volts Gloving by conventional work position or by structure
mounting (ground potential)
0.601 to 7.5 kilovolts Gloving from structure mounting or in an aerial lift
bucket (ground potential)
7.6 to 15 kilovolts Gloving from electrically insulated aerial lift bucket or
platform (intermediate protection) or gloving and use
of live-line tools from structure mounting or an aerial
lift bucket (ground potential)
15.1 to 36 kilovolts Gloving and use of live-line tools from an electrically
insulated aerial lift bucket (intermediate potential)
1
Applies to de-energized line work until lines have been grounded.
5.4.2.1 Rubber Goods. Use insulating (rubber) goods meeting the requirements
of ASTM F 18 standards with color coding meeting the requirements of Table 3. Use
leather protectors over rubber gloves.
Note
5.4.2.2 Insulating Tools. Use insulating tools meeting the requirements of Table
31 and ASTM F711, Specification for Fiberglass Reinforced Plastic (FRP) Rod and Tube
Used in Live-Line Tools, and IEEE Std 978, Guide for In-Service Maintenance and
Electrical Testing of Live-Line Tools. Use approved gloves and rubber insulating sleeves
with hot-line tools. The use of hot-line tools without gloves to detect tool deterioration is
prohibited. Complete instructions and regulations detailing correct use and maintenance
of such tools/equipment should be available and reviewed as a part of the work
procedures. At least two workers, fully qualified for the voltage range (including other
conductors within reach) should be available.
44
MIL-HDBK-1025/10
Table 32
Insulating Tools for Electrical Workers
Minimum test values
Tool material OSHA acceptance1 IEEE in-service2 Use
FRP 0.3 meters (100 kV/foot) 0.3 meters (75 kV/foot) Preferred3
Wood 0.3 meters (75 kV/foot) 0.3 meters (50 kV/foot) Phase-out4
1
Test values manufacturers should certify for acceptance by buyer.
2
Test values required after acceptance and tested after use in the field. Electrically test at
intervals of not more than 6 months for tools in frequent use. Electrically test at intervals of
not more than one year for tools stored for long periods of time.
3
All new tools will be FRP.
4
Replace wood hot line tools with FRP tools.
5.4.2.3 Insulating Guards. Use insulating plastic guard equipment meeting the
requirements of Tables 33 and 34; ASTM F712, Test Methods for Electrically Insulating
Plastic Guard Equipment for Protection of Workers; ASTM F 968, Specification for
Electrically Insulating Plastic Guard Equipment for Protection of Workers; and ASTM F
15684, Specification for Structure Mounted Insulating Work Platforms for Electrical
Workers.
Table 33
Common Classification for Plastic Guards
Common classifications for plastic guards
Installation Conductors Structure/apparatus Special
Attached hot stick Line guards Pole guards Shape
Eye for removable hot Line guard connectors Ridge pin covers Size
stick Insulator covers Switchblade covers Attachment
Rope loop or Deadend covers Arm guards More stringent
equivalent for gloving Bus guards Cutout covers electrical requirements
or hot stick Bus “T” guards Crossarm guards
45
MIL-HDBK-1025/10
Table 34
Insulating Plastic Guards/Platforms for Electrical Workers
Guard rating for accidental brush contact
Maximum use rating kV Proof test withstand voltage
Class (60 Hz) (in-service testing) Criteria
Phase-to- Phase-to- Phase-to-ground kV Duration,
phase1 ground 60 Hz dc minutes
2 14.6 8.4 13.0 18 1
3 26.4 15.3 24.0 34 1 No flashover other
than momentary as
4 36.6 21.1 32.0 45 1 a result of too close
5 48.3 27.0 42.0 60 0.5 spacing of electrode
6 72.5 41.8 64.0 91 0.25
1
Cover-up materials are tested at values greater than the 60 Hz use maximum phase-to-ground
values. The maximum use phase-to-phase values relate to guarded-phase-to-guarded-phase.
The units are not rated for bare-phase-to-guarded-phase potentials.
WARNING
Table 35
Prework Procedures
I. Work Approval. Obtain energized work approval.
46
MIL-HDBK-1025/10
WARNING
Table 36
Energized Work Precautions
C. Check that circuit automatic reclosing devices have been made inoperative while work
is being performed.
D. All items of a voltage class lower than required for the work should not be available to
the workers at the work site.
E. Exercise special care when working in the proximity of equipment such as fuses, surge
arresters, and similar equipment, or where conductor checks indicate burns or other
defects in conductors, tie wires, and insulators. Procedures may require that some
equipment be bypassed for the duration of the work.
F. Comply with adverse weather and number of qualified worker requirements.
Table 37
Voltage Level Work Procedures
47
MIL-HDBK-1025/10
Table 37 (Continued)
Voltage Level Work Procedures
O. Voltage levels, 601 to 15,000 volts
P. Ground vehicles and aerial lifts in the vicinity of the work site.
Q. Cover with approved protective equipment, or isolate with suitable barriers, energized
phase and neutral wires, ground wires, messengers, and guy wires in the vicinity of the
work. Apply covering to the nearest and lowest conductor first and remove in reverse
order. See Tables 24, 25 and 26.
R. Use approved live-line tools where required by Table 31. Rubber will be worn when
entering a glove-required area and removed only after leaving that area.
S. Observe the working distance requirements of Table 11.
T. Protective equipment and vehicle grounds will be removed at the end of each workday.
U. Work performed should be under the direct supervision of a qualified work leader
devoting full time and attention to the workers and the safety of their work.
V. Perform work on only one conductor at a time, although it is recognized that three-
phase lifting tools may be used.
W. When moving an energized conductor with live-line tools, stay below the conductor
until it is firmly secured in a safe working position
X. Do not raise, move, or lower conductors more than 0.45 meters (1.5 feet) when
energized at 7,500 to 15,000 volts. Do not move conductors energized at more than
15,000 volts.
48
MIL-HDBK-1025/10
6.1.3.1 Protective Devices. Protective devices within the system, such as relays
and fuses, which are to be worked on or replaced, should retain respectively their correct
coordination settings or be of the proper size and type. Always record previous data so
that changes in system coordination are not made.
49
MIL-HDBK-1025/10
b. Identify defective equipment by painting a large red X on the body, not on the
top of the equipment. The red X should remain on such equipment until it has been
repaired or until it has been properly disposed of.
6.2 Substation Work Area Control. Control of the work area is essential
for accident prevention. Procedures for specific maintenance may vary but certain rules
are basic to all work.
WARNING
50
MIL-HDBK-1025/10
operating aspects. If for any reason there is an interruption in the work, or conditions
change, another conference briefing will be conducted to familiarize all of the workers
with the new conditions.
b. Tape should completely enclose the work area, be visible from all approach
areas, and be at an effective barrier level. The area enclosed should be large enough to
provide worker safety and arranged so any test equipment can be operated outside the
taped area.
c. Temporary barriers and barricade tape will not be used as a substitute for guard
railings, for work platforms, or for protection from holes in the floor. Information tags or
other warning devices will be provided to identify a hazard that is not obvious.
51
MIL-HDBK-1025/10
6.2.3.4 De-energizing Proof Testing. All lines and equipment on which de-
energized work is to be performed will be tested to be sure they are de-energized before
protective grounds are applied.
6.2.3.5 Work Area Grounding. After indication that all circuitry in the work
area is de-energized, provide protective grounds as covered in Section 5. Place grounds
so that each ground is readily visible to at least one member of the crew. Stay clear of
cables and connecting devices while grounds are being applied.
a. Flexible blankets will not be used at grade level without protecting them from
physical damage and moisture by means of a tarpaulin, canvas, or protective mat.
b. To avoid corona and ozone damage, rubber protective equipment will not be
allowed to remain in place on energized lines or apparatus overnight or for more than one
8-hour period, unless approved by the supervisor in charge.
e. Lack of fire prevention and first aid equipment and inadequate working
equipment and tools.
52
MIL-HDBK-1025/10
WARNING
6.3.2 Lighting Level. The lighting level will be sufficient for safe work.
Temporary self-contained lighting systems will be provided where normal natural or
installed lighting is not sufficient, available, or safe.
6.3.3 Working Period. Normally no worker will work more than a standard 8-
hour period with suitable breaks. Under emergency conditions a maximum of 12 hours
may be necessary but the work period will be preceded and followed by a minimum of 8
hours off.
6.3.5 Equipment Preparation. Check that all control power has been de-
energized and all stored-energy mechanisms have been discharged. All stationary (bolted
or plug-in) nondrawout type circuit breakers should be de-energized on both the line and
load side. All drawout circuit breakers should be checked to be sure that interlocks
(which prevent the circuit breaker from being withdrawn in the closed position) have not
been defeated or bypassed.
53
MIL-HDBK-1025/10
voltage the person in charge of the testing should, in addition to other applicable
instructions in this handbook, take the following precautions:
a. Use only devices that have been checked and found to be properly calibrated
both immediately before and immediately after the test.
b. When testing live circuits or equipment, all temporary leads used in testing
should be securely supported to prevent interference with other workers or injury to the
tester. Protect testing personnel and others (particularly their eyes) from flashovers.
c. When performing mechanical tests, keep the operating personnel and others at a
safe distance or in a safe location by means of barricades, to prevent injury resulting from
the failure of the equipment being tested.
d. Use an approved voltage detector when testing for blown fuses on low-voltage
circuits. Do not use fingers as the test for blown fuses.
WARNING
6.5.1 Air Switches. Most switches today are airbreak switches. Many
switches cannot be opened if there is a load on the line, if there is a large transformer
magnetizing current from transformer, or if there is a heavy charging current from an
unloaded transmission line. Always know the interrupting capabilities of the switch you
are opening or closing.
54
MIL-HDBK-1025/10
loadbreak type. Switch sticks providing the minimum working and clear hot stick distance
are used to manually operate switches. They should be used for no other purpose.
Always assume that disconnect switches are not of the loadbreak type, unless you have
positive proof otherwise and then operate on the following basis.
a. Disconnect switches may be used with care to open a live line, but not under
load.
a. Ground mats should be provided for the operator to stand on with both feet.
Either fixed or portable small iron-mesh mats should be used. The mats should be
electrically connected to the operating rod and the substation ground grid to equalize the
ground gradient and prevent any potential differences in case of insulation failure or
flashover. Rubber gloves should be worn by the operator.
b. The hinges of airbreak switches should be sufficiently stiff (and kept in this
condition) so that when the blades have been turned into the open position they will not
accidentally fall back on their line-side energized clips.
c. The switch should be inspected after it has been opened to see that all blades
have opened the proper distance. Single-throw airbreak switches should be opened to the
maximum amount. Double-throw airbreak switches should be opened so that the blades
clear both sides of the switch by the same amount.
d. Locks will be provided for all airbreak switch operating mechanisms and they
will always be kept locked, except when opening or closing the switch.
55
MIL-HDBK-1025/10
a. Unless the switch has been equipped to operate from a remote location at least
6 meters (20 feet) away, the switch should be completely de-energized before switching.
Switch position and grounding conditions should be verified before operation. Many
manufacturers recommend that no medium-voltage oil switch is to be operated unless
routine maintenance, including oil testing, has been performed within the past year.
6.6.1 Fuse Handling. Fuses should normally not be handled, except when they
need to be replaced. Remove them completely and as speedily as possible. When
replacing fuses in primary fuse cutouts, do not use your free arm to shield your eyes from
possible flashes. Always use safety glasses. The person changing the fuses should stand
firmly on a level surface and, where operating in an elevated position be secured with a
safety harness to prevent a slip and fall if there is a flash. Fuse sticks should be used in all
instances.
6.6.2 Operation of Energized Fuses. Open all lines protected with energized
fuses in the same manner as for air switches. De-energize nonloadbreak installations. For
loadbreak installations provide a time delay after fuse replacement, in order to allow the
56
MIL-HDBK-1025/10
fuse to interrupt any fault condition that was not corrected at the time of the fuse
replacement.
6.6.3 Open Fuse Holder. Do not leave outdoor fuse holders open for an
extended period of time, as water damage or warpage from the elements may make
closing them dangerous or degrade their protective ability.
CAUTION
6.7.1 Surge Arresters. A surge arrester limits overvoltages and bypasses the
related current surge to a ground system that absorbs most of the energy. The
overvoltage condition can be caused by a fault in the electrical system, a lightning strike,
or a surge voltage caused by switching loads. All surge arrester equipment should be
considered as loaded to full circuit potential, unless it is positively disconnected from the
circuit. Be sure the permanent ground conductor is intact before any work is done.
6.7.1.1 Surge Arrester Contact. Substations with grade level surge arresters
should always be provided with screens or fences to prevent possible contact while parts
of the surge arresters may be alive. The screen or fence should have a gate large enough
to permit the removal of individual units. The gate should be provided with a lock and the
key should be kept by an authorized person. Surge arresters should never be touched,
unless they are completely disconnected from all live lines and live equipment and until all
parts have been discharged to ground and effectively grounded.
57
MIL-HDBK-1025/10
6.7.2 Choke Coils. Choke coils are inductors that operate in a manner similar
to surge arresters, except that they operate on overfrequency rather than overvoltage.
c. Safe practice requires that the ground and short-circuit placed on capacitors be
left on until work has been completed. When working on or testing capacitors in the
shop, the work area should be barricaded as a safety measure for other workers.
58
MIL-HDBK-1025/10
CAUTION
a. Also, before any inspection or replacement is done, be sure the service to the
primary side of the voltage transformer is disconnected.
59
MIL-HDBK-1025/10
CAUTION
The main risk involved with the maintenance of current
transformers occurs when the secondary side is unintentionally
opened while the primary side is energized. Opening the
secondary side causes a very high voltage to be set up in the
secondary winding, which stresses the insulation and presents a
serious personnel hazard.
WARNING
a. When transformers are installed or replaced, the secondaries will be checked for
correct voltage and, where applicable, for phase rotation.
b. When transformers are installed, and before they are energized, the ground
connection will first be made to the case and to the neutral when applicable.
60
MIL-HDBK-1025/10
e. When relieving pressure on transformers, the pipe plug, pressure relief device,
or inspection cover plate will be loosened slowly, so that the internal pressure of the
transformer will dissipate gradually. Pressure relief valves will not be opened when there
is precipitation or high humidity, except on failed transformers and when re-fusing.
6.9.2 Voltage Regulators. Voltage regulators are installed with bypass and
disconnect switches.
WARNING
6.10 Metal Clad Switchgear Safety. Metal clad switchgear is inherently safe
to maintain so long as manufacturer's instructions and the following rules are adhered to.
61
MIL-HDBK-1025/10
b. Trip the circuit breaker open and discharge the stored-energy mechanism if
provided.
a. When both sets of portholes in a cell are de-energized, that is line and load or
bus to bus.
b. After both are de-energized, the access to switchgear terminals through the
portholes will be permitted for cleaning, inspecting, and maintenance of terminals and
bushings.
c. Use an approved ground and test device for access to terminals. Such access
may be for application of protective grounds, phase identification on de-energized circuits,
and phasing tests on live circuits. The use of a ground and test device positively and easily
grounds the incoming cables and the switchgear bus. It also permits easy external
connection points to the bus or cable for testing.
b. Check that control circuits are de-energized by pulling fuses on control circuits.
d. Ensure that all crew members are aware of that you are racking in.
62
MIL-HDBK-1025/10
WARNING
b. Network protectors are designed to operate within the current and voltage
limitations given on their nameplates. Do not apply these units to systems with currents
and/or voltages exceeding these limits.
d. There are several interlocks on a network protector. They are for personnel
and/or equipment protection. Under no circumstances should they be made inoperative.
e. Roll out the network protector's removable element before making any
adjustments or doing maintenance of any nature.
f. Never energize the network protector without its arc chutes and barriers in
place.
g. Always be sure that all network protector hardware is in place and bolted
tightly before placing a network protector into its housing for operation.
h. Since network protectors are used where a large amount of power is distributed
to heavy-load density areas, any short circuit at any point in the system involves very high
fault currents. Extreme care should be exercised when installing or working on an
energized network protector.
63
MIL-HDBK-1025/10
i. The extensive use of barriers and interlocks as a part of the network protectors,
provides greater safety to maintenance personnel. Keep barriers in place and immediately
replace any that have been broken. Although barriers and interlocks are provided,
insulated tools and/or insulated gloves are required to remove the rollout unit from the
enclosure, and to remove fuses, or at the initial installation of the network protector on the
system.
Note
CAUTION
a. Storage batteries are most often lead acid type but nickel-cadmium batteries are
also used. Flood-cell (vented) technology or valve-regulated technology may also be
installed. These different types have different charging/discharging characteristics and
their hazardous emissions require different handling operations. NAVFAC MO-200,
Chapter 14 covers their maintenance and operating requirements.
b. Smoking or the use of any open flame, such as torches, will not be permitted
around batteries. When soldering or lead burning is done, the battery room should be well
ventilated, the battery cell vent plugs should be removed, and the excess gas above the
electrolyte should be blown out of those cells near the work area.
c. Cleaning batteries or terminals with brushes or other devices that may short out
the cell will not be permitted. (The ignition of the hydrogen-oxygen mixture in cells by a
spark from a short on terminals has caused cells to explode).
d. When making up electrolyte for storage batteries, a worker should always pour
acid into the water. The reverse may cause an explosion.
64
MIL-HDBK-1025/10
e. When doing work on batteries where contact with the electrolyte can be made,
a container with baking soda and water should be provided for workers to neutralize the
electrolyte on hands and tools. A working eye wash should be available close to the
batteries. If none is present or if the one provided is inoperable, a portable eye wash will
be immediately provided for the workers’ use.
g. Do not store sulfuric acid in places where freezing temperatures can occur.
h. For further information on servicing and maintaining storage batteries, see the
manufacturer's instructions.
65
MIL-HDBK-1025/10
7.1 Pole Linework Environment. Comply with the requirements of OSHA standard
29 CFR 1926(q) “Overhead Lines.” The majority of the work will be done in an elevated position
above ground level. Climbing aerial line structures such as poles may be required. Situations
with limited structure access can prevent use of an aerial lift bucket truck. The structure design
may not accommodate positive fall protection load requirements. Only workers who meet
"Qualified Climber" requirements should be permitted to do work which requires climbing poles
or trees. Each facility should establish “qualified climber” requirements both for facility personnel
and for contract personnel. They should apply to all persons whose work involves climbing.
a. Physical fitness required for climbing should be documented not only by an annual
physical, but also be validated by supervisory observation.
b. Climbing duties should be a part of routine job activities, not an occasional occurrence.
e. A worker in training may function as qualified only when working under the direct
supervision and observation of a "Qualified Climber."
Note
66
MIL-HDBK-1025/10
Note
c. The activity is being performed under the direct supervision of a designated person
who is trained and competent in this type of work.
d. The distances between energized parts and the aerial lift equipment is monitored while
the aerial lift equipment is being moved and/or repositioned.
f. No one, other than necessary workers, are within 3 meters (10 feet) of the equipment
during its operation. Workers are to perform their work while on the equipment; not from a
position on the ground.
7.2.2 Types of Aerial Lifts. Aerial lifts include the following types of vehicle-mounted
aerial devices used to elevate personnel to job-sites above ground.
b. Aerial ladders.
d. Vertical towers.
67
MIL-HDBK-1025/10
Note
CAUTION
a. Aerial ladders will be secured in the lower traveling positions by the locking device on
top of the truck cab and the manually operated device at the base of the ladder, before the truck is
moved for highway travel.
b. Lift controls will be tested each day prior to use to determine that such controls are in
safe working condition.
d. Belting off to an adjacent pole, structure, or equipment while working from an aerial
lift will not be permitted.
e. Workers will always stand firmly on the floor of the bucket and will not sit or climb on
the edge of the bucket or use planks, ladders, or other devices for a work position.
f. A body harness will be worn and a lanyard attached to the boom or bucket while
working from an aerial lift.
g. Boom and bucket load limits specified by the manufacturer will not be exceeded.
h. The brakes will be set and outriggers, when used, will be positioned on pads or a solid
surface. Wheel chocks will be installed before using an aerial lift on an incline, provided they can
be safely installed.
i. Generally, an aerial lift truck will not be moved when the boom is elevated in a working
position with workers in the bucket.
68
MIL-HDBK-1025/10
be operated unless permission has been obtained from the worker in the lift, except in case of
emergency.
k. Climbers will not be worn while performing work from an aerial lift.
l. The insulated portion of an aerial lift will not be altered in any manner that might reduce
its insulating value.
m. Before moving an aerial lift for travel, the boom(s) will be inspected to see that
equipment is properly cradled and outriggers are in the stowed position.
CAUTION
a. The operating and maintenance instruction manuals issued by the manufacturer will be
followed.
d. The operator will always face in the direction in which the bucket is moving and will
see that the path of the boom or bucket is clear when it is being moved.
e. Workers will not ride in the bucket while the truck is traveling. (Exceptions: Workers
may ride in the bucket for short distances at the work location if the bucket is returned to the
cradled position for each move and the workers face the direction of travel.)
f. When workers are in the bucket of an aerial lift, the emergency brake of the vehicle will
be set. Wheel chocks or outriggers will be used to provide added protection. When the vehicle is
on an incline, wheel chocks will be used regardless of whether or not outriggers are used. The
truck should sit approximately level when viewed from the rear.
g. Workers will not stand or sit on the top or edge of the bucket or on ladders placed in
the bucket. Workers' feet will be on the floor of the bucket the entire time they are in it.
69
MIL-HDBK-1025/10
h. When two workers are in the bucket or buckets, one of them will be designated to
operate the controls. One worker will give all signals, which will be thoroughly understood by all
persons concerned.
i. When two workers are working from the bucket, extreme care will be taken to avoid
one worker contacting poles, crossarms, or other grounded or live equipment while the second
worker is working on equipment at a different potential.
j. In no case will more than one energized conductor or phase be worked on at a time.
k. The aerial lift, including workers in the bucket and all tools and equipment will be
maintained at proper clearances from unprotected energized conductors. Safety requirements
governing the use of hot-line tools, rubber goods, personal protective equipment, and general safe
practices will also apply to work done from aerial buckets.
l. When using pneumatic or hydraulic tools in a bucket, the operator will be sure that
hoses or lines do not become entangled in the operational controls or contact adjacent energized
conductors.
Note
a. Remove water accumulation from the bucket. The bucket interior should be dry during
use.
b. Wipe exposed insulation of bucket and boom clean with a dry cloth at the start of each
day.
c. Inspect visible hydraulic hoses for chafing and then inspect hoses and fittings for leaks
with the system under pressure.
f. Verify that the most recent dielectric test for the bucket and arm occurred within the
last 6 months.
70
MIL-HDBK-1025/10
g. Examine the exposed insulation of an insulating boom for cuts, unusual discoloration,
or other signs of damage prior to use or at any time damage is suspected.
h. Inspect the remaining portions of booms, sheaves, cables, fittings, bucket, and bucket
liner for defects.
Note
Insulated buckets are required for work in accordance with Table 31. An
insulated bucket of an aerial lift is provided with a conductive bucket
liner.
a. The liner, usually a metallic screen, should completely surround the bucket walls and
floor to provide electrostatic shielding for the occupant. Tools and other equipment carried in the
bucket should be stowed carefully to avoid damaging the liner.
Note
71
MIL-HDBK-1025/10
CAUTION
Precautions are necessary in handling poles safely. Poles are long, heavy,
and preservative-treated, thus they pose hazards to the workers involved
in installation and dismantling operations. Any mistreatment of poles
during installation will degrade their ability to meet service requirements
and endanger those workers who climb them.
7.3.1 Direction of Aerial Lift for Installations. The foreman should direct the
handling of poles and give all signals when poles are being lifted or handled. Poles should,
whenever possible, be handled starting from the top and the end of the stack. Workers should roll
poles away from them using cant hooks or bars. Poles should not be caught with cant hooks
while in motion. Whenever possible, carrying hooks should be used when carrying poles.
WARNING
b. Always wear gloves, and keep your neck well covered with a collar or a handkerchief.
c. Always keep trousers well down over your ankles as much as practical.
d. Never rub your eyes or wipe perspiration from your face with your hands or shirt
sleeves when they have been exposed to creosote.
e. Where direct contact with creosote is apt to occur, the hands, arms, and face may be
rubbed with a preparation made up of one part gum acacia or gum tragacanth and three parts
lanolin. If this preparation cannot be obtained, satisfactory protection can be provided by
petroleum jelly (Vaseline). First aid treatment should be obtained immediately if you come in
body contact with creosote.
7.3.3 Facility Receipt. Poles are usually shipped to the facility's pole storage yard on
flatbed cars, on which they are secured with skids, stakes, slings, and bindings. Shipping removal
72
MIL-HDBK-1025/10
is safe if done properly. The principal objective is to unload poles so that none are broken and so
that the poles do not roll onto any worker.
a. Skids, rope lines, and slings should preferably be wire rope having a diameter of 12.5 to
16 millimeters (1/2-inch or 5/8-inch). These should be inspected to ensure they are sufficiently
strong enough for the operation.
b. All binding wire, stakes, and other fastenings will be inspected for weakness or
breakage before unloading.
c. Always place necessary lines to restrain loads when stakes and binding wires are cut.
d. The supervisor will determine that all possible persons are safely in the clear before
binders or stakes are cut.
e. Binding wires should be cut with long-handled wire cutters. Never cut binders from
the top of the load.
f. Only one person should be permitted on top of a loaded car at a time. No one should
be allowed on top of a carload of poles to cut wires or after any wires or braces have been cut or
removed.
CAUTION
Once on the ground the poles can be positioned by the use of cant hooks.
Special precautions should be taken while using these hooks.
b. The hook bolt should be inspected occasionally to detect wear. When a worn hook
bolt breaks in use, a sudden and severe fall can result.
c. Injuries may result when the handle breaks or the hook comes out. Therefore, make
sure the hook is firmly set in the pole.
d. The cant hook is a one-worker tool and frequently breaks when two workers double
up. If the job requires two workers, two cant hooks should be used.
e. Before moving the pole, make sure that there are no tripping hazards behind any
workers.
73
MIL-HDBK-1025/10
f. Stand so the pole is rolled away from you. Pulling the pole toward you can allow the
pole to roll on your foot or even crush your leg. Also watch to see that the pole does not roll up
a hump, as the pole could roll back when the grip and position of the hook is changed.
7.3.5 Temporary Pole Storage. Storage of poles should ensure that they will not
deteriorate because of mishandling.
a. Poles that are stored for considerable periods should be stacked above the ground on
racks that provide sufficient ventilation and can be properly blocked to keep them from shifting or
rolling.
b. Poles should never be stored with cross-arms, braces, steps, and hardware attached.
d. An area of at least 3 meters (10 feet) around stored poles should be kept free of grass
and weeds. There should be sufficient space under the poles to permit removal of leaves and
debris. The foreman is responsible for these activities.
7.3.6 Hauling Poles. Pole hauling should be done so as not to endanger workers
and/or the public.
a. Poles, after being loaded on a vehicle, should be secured in at least two places and in a
manner that ensures poles will not be released in traveling over rough terrain. Never use a chain
smaller than 9.5 millimeters (3/8 inch) in diameter.
b. A minimum of at least two people (a driver and a helper) should be assigned to haul a
load of poles. The helper should assist the driver by watching traffic both from the sides and the
rear. The helper should also see that there is ample clearance when turning corners, entering
highways, or crossing intersections. If necessary, the helper should act as flagman to warn and
guide traffic.
d. Poles extending more than 1.2 meters (4 feet) beyond the back of a truck or trailer will
have warning devices attached. Provide a red flag by day and a red light by night to the rear end
74
MIL-HDBK-1025/10
of the poles being hauled. The red flag or light should be visible in any direction. State highway
regulations should be observed when poles are transported on state highways.
e. Poles temporarily dispersed along streets and highways should be laid near the curb or
in parkways between the curb and sidewalk, where they will not interfere with traffic, driveways,
or walkways. When laid on an incline, poles should not be placed where they will interfere with
drainage. The foreman should decide whether or not danger signs by day and red lights at night
are required.
f. When moving a pole by hand, with a pole cart or with the truck derrick, warn those
nearby who might be struck accidentally. Station a worker with a red flag to warn or stop traffic
as necessary.
7.4 Pole Installation Requirements. Poles will normally be installed for new aerial
line construction by contract workers. However, facility-installed poles may be needed for short
line replacements of storm-damaged lines or because of pole decay. These poles may be installed
by either Navy or contract workers. Remember that poles and guys should be located relative to
local facility property line requirements.
7.4.1 Pole Holes. If new poles are to be set adjacent to existing poles to be dismantled,
new holes should be dug. Power tools are available for digging, such as power borers or augers
and should be used by qualified personnel. Rock cutting drills are available, as a safer alternative
to the use of explosives, where rock is encountered. Most facility-provided pole holes will
probably be dug by hand when power diggers are unavailable or cannot be used.
7.4.2 Digging Holes. Digging pole holes does not involve any great hazard, but does
contribute to a great number of minor injuries, such as eye injuries from flying dirt and rocks;
blisters on hands from the use of hand tools (blisters can be partially eliminated by using gloves);
and foot and leg injuries resulting from falling over tools left too close to the pole hole,
particularly shovels that have been left turned up.
7.4.3 Hole Covers. Hole covers should be at least 750 millimeters (30 inches) in
diameter. Covers may be made of 25 millimeters (1-inch) thick lumber with two cross braces not
smaller than 25 by 100 millimeters (1 inch by 4 inches) in cross section. Four or five shovels of
soil should be put on the cover after it is placed over the hole. Casings may be required in sand or
swampy soil to prevent the sides of a hole from caving in. Casing covers are required if pole
setting is not done immediately.
75
MIL-HDBK-1025/10
Note
Cover all open pole holes as soon as they are dug, except when the pole
is to be set into the hole immediately after digging.
7.4.4.1 Pike Pole Method. Figure 9 illustrates the pike pole method. This is the earliest
method of raising poles and should be employed when a truck cannot be brought in. A jenny
initially supports the pole and a cant hook keeps the pole from rolling. The bumpboard protects
the wall of the hole from being caved in by the pole butt. Pikers, lift the line pole, by punching
into the pole the steel spikes of the pike poles.
HEAVY
PIKERS
4.3 METERS
(16 FEET)
CANT
HOOK
BUMP-
5 METERS BOARD
(14 FEET)
JENNY
GUIDE PIKERS
3.6 TO 4.3 METERS
(12 TO 14 FEET)
Figure 9
Pike Pole Method
a. Before setting a pole the foreman should ensure a clear working space and verify that
all movable obstacles are removed from the area. Personnel should not wear safety harnesses and
climbers when setting poles. Tools or other items may not be substituted for bumpboards.
Always use a jenny to support the pole until it is high enough to use pikes. Only experienced
workers should use the jenny. The angle of contact between the pole and jenny should be
maintained as close to 90 degrees as possible.
b. At least three experienced pikers should be used in addition to the supervisor. The
number of pikers required increases with the pole length as shown on Table 38. One person
should handle the butt of the pole and a minimum of two side pikers are needed. Inexperienced
workers used in this work should be thoroughly instructed on the hazards involved. A two-
76
MIL-HDBK-1025/10
legged jenny should be used. It is the responsibility of the supervisor to assure that all pole-lifting
tools are always in good condition.
Table 38
Average Size of Crew Required to Raise Poles of Different
Lengths by Piking
Pole length in Size of Number of Number of Number of
Meters (feet) crew pikers jennymen people at butt
7.5 (25) 5 3
9.0 (30) 6 4
10.5 (35) 7 5
1 1
12.0 (40) 8 6
13.5 (45) 9 8
15.0 (50) 10 8
7.4.4.2 Winch Line Method. Figure 10 shows the winch line method.
WINCH
LINE
WORKER
IN CLEAR
WORKER
WITH
CANTHOOK
BUMPBOARD
WORKER
IN CLEAR
Figure 10
Winch Line Method
a. When erecting poles by truck winch and winch line, rig as shown with all workers in
the clear. At least three experienced workers should be used in addition to the supervisor. For
safe erection, the gins or maneuverable rigging assembly should have enough teeth to handle the
pole. Pikes should not be used in combination with a winch.
77
MIL-HDBK-1025/10
b. Side guys used in setting poles or structures are attached to pencil bars driven into the
ground. Tie lines or other guy lines should never be wrapped around any worker's body. The
supervisor should concentrate on supervising the work to assure that it is being safely performed.
7.4.4.3 Gin Pole Method. In setting extra-heavy poles or those of 12.5 meters (45 feet)
or longer, use a tackle block attached to another pole (either existing or specially set for the
purpose of raising the new pole) rather than the pike pole method. The pole used as a gin
(maneuverable rigging point) to raise the new pole, should be guyed sufficiently with not less than
16-millimeter (5/8-inch) diameter rope to hold it erect under the strain of the load. When the new
pole is raised by car or truck, the temporary guy should be run from a snatch block at the bottom
of the gin pole to a substantial anchor. This prevents the gin pole from slipping at the ground line.
Otherwise the gin pole should be set in a hole 0.3 to 0.6 meters (1 or 2 feet) deep.
7.4.4.4 Pole Setting Truck Precautions. Pole setting trucks should be parked, when
practicable, so that the steel boom will not be closer than 3 meters (10 feet) to energized overhead
conductors. When the work is to be done around energized conductors and it is impossible to
lower the boom sufficiently to be in the clear, the conductors should be de-energized before work
is begun. When work is being done with the boom close to energized conductors, all personnel
should not touch the pole and should keep away from the frame of the truck. Never touch (with
bare hands or with any part of the body) a pole that is being set in an energized line. A cant hook
or dry rope around the butt of the pole may be used to guide it into the hole.
WARNING
78
MIL-HDBK-1025/10
a. Wood poles should not be considered as providing insulation from energized lines.
7.4.4.6 Backfilling Around Poles. Backfill the hole after the pole has been placed. Use
the pikes to align the pole while backfilling. Pikes should not be removed until sufficient tamping
has been done to prevent the pole from falling.
WARNING
7.5.1 Minimum Pole Support. Each pole should be guyed in at least three different
directions by guy ropes before any work proceeds on the pole using the following procedure:
a. Make two turns around the pole with a sling and tie securely.
b. Tie three guy lines around the sling at the proper angles.
c. Insert pike poles under two sides of the sling well up the pole.
d. Snub off securely by pencil bars driven into solid ground or by any other substantial
snub.
7.5.2 Additional Pole Support. Always check the pole to see if additional support
may be necessary because of pole conditions or strains.
a. Determine the condition of the pole butt before removing guys or wires and support
with additional pike poles or temporary guys if necessary.
c. When changing the strain on a pole, the foreman should see that it is sufficiently guyed
to stand the altered strain. The foreman should not permit workers to climb a pole that is under
an abnormal strain. The foreman should be responsible for the placing of guys to prevent any pole
from falling.
7.5.3 Truck Restraining. A truck equipped with an "A" frame and backed up to the
pole can be used to restrain the pole. The top of the "A" frame can be tied by the winch line to
the pole. The pole at the groundline level can be securely tied off to the truck.
79
MIL-HDBK-1025/10
WARNING
7.6 Climbing and Working on Poles. Workers should be familiar with general rules
for climbing poles and approaching the overhead work area; the impacts of climbing wood poles
as opposed to steel towers; and the dangers of crossing structures from one side to another.
d. The best climbing space to avoid all live wires, grounded wires, and signal circuits.
f. That not more than one worker will descend a pole at the same time. The first worker
should be in place on the pole or down on the ground before the next worker ascends or descends
the pole. When it becomes necessary for one worker to work above the other, they will exercise
extreme care.
80
MIL-HDBK-1025/10
g. Before climbing poles, ladders, scaffolds, or other elevated structures; riding span
wires, messengers or cables; or entering cable cars, boatswain chairs or similar equipment; the
worker will first verify that said structure or device is strong enough to safely sustain his/her
weight.
WARNING
The type of pole to be climbed will affect the precautions that the worker should
take in regard to climbing equipment and procedures. However all types of poles
should be safe to climb, in terms of being strong enough to bear the weight of
particular climbers and their tools and in providing adequate climbing space.
Before allowing anyone to climb on a pole, the supervisor will ensure the pole is
inspected and that it can be safely climbed based on the following determinations:
a. Age, treatment, and physical condition of each pole should be tested in accordance
with the applicable provisions of MO-200, Facilities Engineering, Electrical Exterior Facilities.
Poles unsafe for climbing should be reported to the foreman so that they may be braced or guyed
before climbing.
d. Poles to be climbed are in such condition and are supported in such a way as to safely
support workers on such poles. Pikes will not be used as a support method while personnel are
working on poles.
WARNING
Usually pole climbing will be done on wood poles rather than on concrete or steel
poles. The two major differences between these types of poles are that wood poles
are not grounded poles (although they should not be counted as providing protective
insulation) and climbing wood poles (along with trees) requires climbers (gaffs) rather
than step bolts or ladders. All workers need to be provided with body harnesses and
safety straps when climbing and while working more than 1.8 meters (6 feet) above
ground level. Positive fall protection may also be appropriate.
81
MIL-HDBK-1025/10
Note
a. Climbing equipment should be carefully inspected daily. Leather should be checked for
cuts, cracks, and enlarged buckle tongue holes. Metal parts should be checked for cracks, wear,
or loose attachments. Climbers (gaffs) should be regularly checked for proper cutting edges,
length, and shape.
b. The foreman, or a properly delegated worker, will inspect all tools, safety devices, and
other equipment weekly. Any item that is not considered safe will be condemned, regardless of
ownership, and should not be used.
d. Positive fall protection. Provide positive fall protection where the strength of the pole
(steel/concrete) permits meeting OSHA requirements. Exceptions are ascending or descending by
a qualified climber or situations where a job hazard analysis so warrants. On wood structures
consider adding position fall protection when transitioning obstructions, if a job hazard analysis
indicates a fall arresting point will provide adequate strength.
Note
Equipment sets each consist of a body harness, a pole strap, and climbers
(an assembly of gaffs, leg straps, and pads). The Edison Electric Institute
provides an excellent document entitled "Use and Care of Pole Climbing
Equipment" which should be used as part of the training for pole climbing
certification.
82
MIL-HDBK-1025/10
c. Leg iron length, sizes range from 380 to 460 millimeters (15 to 18 inches) from instep
to end of shank.
d. Leather straps, two each of 26 millimeters (1-1/4 inches) wide, at least 560 millimeters
(22-inches) long.
7.7.2.2 Climber Defects. Climbers and pole straps or other leather items that have any
of the following defects should not be used until repaired:
c. Cuts or worn places which are of sufficient depth to weaken the leather.
e. Snaps which have weak springs behind the tongue, or loose rivets which hold the
tongue.
g. Buckles, D-rings, or snaps that show considerable wear or which have been cracked or
bent.
7.7.2.3 Leather Treatment. Leather equipment should be cleaned and dressed every 3
months. This period should be shortened when equipment is frequently wet from rain,
perspiration, or covered with dirt or mud.
a. Wipe off all surface dirt and mud with a sponge dampened (not wet) with water.
Never use gasoline or other cleaning fluids as they tend to dry out and harden the leather.
83
MIL-HDBK-1025/10
b. Wash leather with a clean sponge in clear lukewarm water, and a neutral soap (free
from alkali), preferably Castile soap. Thoroughly wash the entire length of the leather and work
the lather well into all parts. Place in a cool area to dry.
c. Leather should be oiled about every 6 months. Use a small quantity, about 20
milliliters (4 teaspoonfuls) of pure neatsfoot oil per set of equipment, and apply it gradually with
the hands, using long light strokes while the leather is still damp from washing. Leave in a cool
place to dry for 24 hours, and then rub the leather vigorously with a soft cloth to remove all
excess oil.
7.7.2.4 Storing Climbing Equipment. When safety harnesses and straps are not in use,
they should be stored in proper compartments on the electric truck or in other suitable places to
protect them from being damaged. When stored, climbers should be wrapped in pairs and
fastened with their straps.
7.7.2.5 Conditioning Climbing Equipment. Climbers, straps, and pads should be kept
in good conditions at all times. Gaffs should be at least 26 millimeters (1-1/4 inches) long,
measured from the point of the gaff to the point of contact with the stirrup on the under side.
Sharpen climbers using a gaff shaping bit as follows:
a. Place the climber between wood in a vise with the leg iron horizontal and the gaff on
the top side.
b. Use a smooth cut file and finish with a sharpening stone. Never grind with an emery
wheel, as this takes the temper out of the metal.
c. File only at and toward the point of the gaff and only on the outside. Never file the
front or flat side except for a slight touching up.
d. Do not file a long sharp point. The sharp part of the point should be about 3
millimeters (1/8 inch) long.
e. Never use a climber with a gaff shorter than 26 millimeters (1-1/4 inches) long, as
measured on the flat side.
84
MIL-HDBK-1025/10
CAUTION
Climbers should not be worn when:
c. Piking poles
WARNING
7.7.3.1 Fall Arresting Device Considerations. A fall arresting device should always be
considered whenever the worker will be working more than 1.8 meters (6 feet) above ground
level on line or substation structures/equipment where a feasible anchor point is available.
Workers should be secured for fall arrest, while climbing or changing work positions, and for
position security while working in place. Where both hands are required for working from a
ladder, the requirements for either fall arrest, position security, or both, will be applied dependent
upon the working height.
7.7.3.2 Fall Arresting Anchor Point. A proper anchor point should be identified and
evaluated by qualified personnel before an appropriate system can be selected. OSHA regulations
indicate that pad eyes, bolt holes, and other sturdy structures, capable of supporting 2,200
kilograms (5,000 pounds) per attached worker, are acceptable.
85
MIL-HDBK-1025/10
7.7.3.3 Fall Arresting System Provisions. Positive systems all have in common an
anchor point independent of the support method, a harness to hold the worker, and a connecting
device between the anchor point and the harness.
a. Harnesses should only be used for the personal protective purpose for which they are
designed. Their misuse could result in serious injury or death. In addition to fall-arrest harnesses,
there are fall-arrest/positioning, fall-arrest/suspension, fall-arrest/retrieval, and
retrieval/positioning harnesses.
b. The use of a harness over a belt is because of its impact limits. A belt provides only
increased for impact forces up to 400 kilograms (900 pounds) while a harness has a higher force
level of up to 800 kilograms (1,800 pounds). All items of the complete fall arrest system should
be taken into account, not just the harness.
c. Manufacturer's instructions in regard to height and weight should be followed for sizing
of the harnesses and their connecting devices and for inspection and maintenance of the complete
systems. All equipment should be taken out of service and inspected for damage after being
subjected to a fall impact.
7.7.3.4 Climbers’ Tools. Workers authorized to climb should have a complete set of
approved tools. The number of tools carried in tool belts should be kept to a minimum.
7.8 Pole Climbing and Work Precautions. Only after determination of the pole's
safety, collection of necessary climbing equipment and work tools, and assurance that the line is
de-energized and grounded, or that hot-line work is authorized to be carried out, can the worker
start climbing.
CAUTION
Protect hands and arms by wearing gloves and long sleeve shirts.
7.8.1 More Than One Climber. If more than one worker needs to work on the pole
at the same time, the first worker should reach working position before the next worker leaves the
ground. Ordinarily, no worker is to work directly under another worker on the same pole, except
in emergencies. When this condition is necessary, take extreme care to prevent tools or other
objects from being dropped on the worker below.
a. Seat the gaffs securely. Be especially vigilant when the pole is ice or sleet covered.
86
MIL-HDBK-1025/10
b. Use pole steps whenever they are available, but only after checking that they can be
used safely.
c. Use the climbers carefully on the pole to avoid injury to another worker on the pole.
d. Every precaution should be taken to avoid weather cracks, checks, knots, shakes, rots,
and hard places, which might cause gaffs to cut out. Remove any tacks or nails which may
impede safe climbing.
The great majority of falls are due to slick work gloves or slick shoe soles.
7.8.4 General Pole Climbing Precautions. The pole climber will observe the
following rules.
b. The worker should not stand on mail boxes, signs, fire alarm boxes, or similar
equipment which may be attached to the pole or located near it.
d. Safety straps should not be attached to the pole while climbing or descending the pole
except in conditions of high winds or severely inclement weather when emergency work is
justified.
e. When climbing over slippery or ice-coated crossarms or timbers, where the hands are
apt to slip off, two safety straps should be used. The use of rope safeties is prohibited.
87
MIL-HDBK-1025/10
f. All signs should be removed from a pole before any worker climbs or does any work
above them on a pole. It is not desirable to have signs on poles, but street signs may be necessary
at times. Where street signs are removed they should be replaced after all work is completed.
g. Climb on the high side of a raked or leaning pole if possible, but do not climb on the
side where the ground wire is attached. Avoid grasping pins, brackets, crossarms, braces, or
other attachments that might pull lose and cause a fall.
h. Never slide down any type of pole or any guy wire. If it is impossible to use climbers
for ascending and descending such places, ladders or other means should be used.
i. Do not ride overhead guys or cables. (This does not apply to cables installed for river
crossings or otherwise intended to support workers in suitable conveyances.)
a. Be careful in attaching snaps to D-rings. Visually ensure that the snap keeper is fully
closed in the correct ring before any weight is applied to the safety strap.
b. Always be sure that safety straps are not twisted while in use.
d. Never attach safety straps above the crossarm in the top gain or around insulator pins,
crossarm braces, transformer hangers, pole steps, or guy wires. If there is no crossarm in the top
gain, the strap should not be placed closer to the top of the pole in a manner that assures there is
at least 0.6 meters (2 feet) to the top of the pole. In this case take precautions to assure that the
strap does not slip off. Ideally the strap should be below the top pole attachment, except where
that attachment is above eye level.
e. Do not permit any worker to fasten both safety harness snaps in the same D-ring in
order to reach out farther on the pole. An extension safety strap should be used or the safety
harness let out so that work can be performed with the safety harness snaps fastened one in each
D-ring.
f. Workers should not attach metal hooks, or other metal devices to body harnesses.
Metal chains and keepers should not be used. Use leather straps or rawhide thongs with hard
wood or fiber keepers. Care should be taken to prevent the snaps on the safety harnesses from
coming in contact with anything that may open a snap. The tongue of the snap on the safety
harness should face away from the body.
88
MIL-HDBK-1025/10
WARNING
Never change the amount of strain on a pole by adding or removing wires
until you are sure that the pole will stand the altered strain. If in doubt,
consult your foreman.
CAUTION
a. Junked material that cannot be lowered safely may be dropped only if there is no
danger to workers or the public.
b. Workers engaged in hoisting tools and materials should be positioned so that they will
not be injured by an accidental dropping of the tool load.
c. Materials and tools should not be left in an insecure overhead position. Large objects
should be securely lashed.
d. Minimize the number of tools carried in tool belts. Secure tools returned to a tool belt.
Keep all other tools on the ground until they are required. Then tools should be raised and
lowered by means of a canvas bucket attached to a handline. If a tool is too large to be safely
raised in this manner, it should be raised by means of just a handline.
e. Carry a handline up a pole uncoiled with one end attached to the rear of the worker's
body harness. When climbing with a handline, take care to prevent the handline from fouling on
any pole attachments.
89
MIL-HDBK-1025/10
WARNING
Never cross through an open air switch, one side of which is energized.
Energized portions of the structure should be blocked off with barriers
and, if advisable, another worker should be stationed to warn anyone
approaching about the danger zone.
7.9.2 Balancing Support on Pole Structures. Never hold onto air switch arcing
horns for support in walking timbers, as these horns break easily and a fall might result.
7.9.3 Climbing H-Frame Pole Structures. Never walk along an H-frame crossarm
with the line energized.
7.10.1 Line Work Precautions. Observe the following work precautions for stringing
or removing lines and for all aerial line work.
7.10.1.1 Adjacent to Energized Lines. When pulling wire over or near energized
conductors, the worker attending the payout reel should wear rubber gloves and be positioned on
an insulated stand of a size equivalent to or larger than a standard rubber blanket. The payout reel
should be grounded. Any deviation on grounding payout reels requires special permission from
the supervisor.
a. A bull rope of dry polypropylene rope not smaller than 19 millimeters (3/4 inch)
diameter is used in stringing. Handlines are not strong enough. The bull rope should be placed in
position to pull the wire before attempting to string it. The bull rope should be of sufficient length
to reach the distance the wire is to be pulled. Fasten the wire to the end of the bull rope and pull
it into position.
b. A car or truck should be used to pull the wire so that the driver can see the signals of
the reel operator. Both in pulling in the wire and in sagging it, the pulling should be slow and
steady to prevent swinging the wires into the energized conductors. The wire should be watched
carefully to prevent its hanging up on tree limbs, weeds, and other obstructions. No workers
should be permitted to touch any conductors or wires on the ground without rubber gloves.
90
MIL-HDBK-1025/10
7.10.1.2 Over, Under, or Across Energized Lines. When wires are strung and sagged
over, under, or across conductors carrying a voltage of 5,000 volts or less, personnel handling the
wire should wear rubber gloves and use other necessary protective devices. Conductors carrying
more than 5,000 volts should be positively and constantly grounded during the stringing
operation. As soon as the wire is ready to be deadended, it should be grounded with standard
grounding devices.
7.10.2 Other Work Precautions Affecting Aerial Lines. Electrical charges may
appear on the line from a lightning strike or from induced static charges from a very dry
atmosphere. Discontinue operations when there is any indication of lightning in the surrounding
area.
7.10.2.1 Fallen Wires. All personnel should look for fallen wires. A worker finding a
fallen wire will stand by it to protect all street and highway traffic and pedestrians from the
hazards. As soon as possible, another worker should be directed to telephone the facilities
engineer or the appropriate superintendent to have the wire de-energized. The worker finding the
fallen wire should not leave until instructed by the supervisor in direct charge.
7.10.2.2 Fire. All electric lines close to a fire should be de-energized immediately to
protect the firemen. The electric lines should not be re-energized until all danger has been
removed. Where electric lines were located close to the fire, the electric lines, ground wires, and
guying should be inspected carefully. Inspect insulators for cracks and crossarms and poles for
charring before the electric lines are restored to service.
7.10.2.3 Vehicular Protection. Wires being strung along or across streets or highways
should be kept sufficiently elevated to eliminate vehicular collisions. The supervisor should
delegate a competent person to act as flagman. Traffic should be blocked when this line elevation
is not possible.
7.10.3.1 Permanent Ground Wires. Permanent ground wires are installed to protect
workers. Remember that the metallic case, covering, or mounting support of any energized piece
of electrical equipment should be considered energized at full voltage if it is not properly
grounded. All permanent grounds should be installed in accordance with the requirements of the
NFPA 70, The National Electrical Code (NEC) or the ANSI C2, The National Electrical Safety
Code (NESC) as applicable.
a. Ground wires should be installed clear of all metallic line equipment (except that which
is normally grounded), hardware, or streetlighting fixtures.
91
MIL-HDBK-1025/10
b. Ground wires on distribution wood poles should be protected with wood molding for
the entire working length of the pole and protected to prevent guy wires from cutting the ground
wires. The entire working length of the pole is from the point where ground wire terminates near
the top of the pole to 1.5 meters (5 feet) below the lowest crossarm or bracket, and from the
ground line to 2.5 meters (8 feet) above the ground line.
c. Never cut an overhead ground wire or neutral wires of any kind because of the need for
line or equipment replacement, unless specifically instructed by your supervisor to do so. Also,
avoid opening a joint in such a wire without first bridging the joint with wire of a suitable size.
7.10.3.2 Common Neutral Systems. Fuses of all transformers should be opened before
work can be done on a transformer bank where the grounded neutral wire is used for both
primary and secondary neutrals. The connections from the transformer to the grounded neutral
should be made before the connection from the transformer to the phase wire is made. The
connection from the transformer to the grounded neutral wire should never be disconnected while
the transformer is energized.
7.10.4 Handling and Stringing Guidance. ANSI/IEEE 524, Guide to the Installation
of Overhead Transmission Line Conductors, provides general recommendations on the methods,
equipment, and tools used for the stringing of overhead line conductors and ground wires. The
following safety precautions are mandatory.
7.10.4.1 Reels. Adequate braking should be used to stop all payout reels. Personnel
should not otherwise touch or attempt to stop the revolving reel.
7.10.4.2 Conductors. The inside end of the coil wire, where accessible, should be
securely fastened to the reel to prevent the wire from getting loose when the wire has been played
out. If the inside end of the coil cannot be secured, a tail rope should be fastened securely to the
wire before the end is reached to prevent its getting loose.
7.10.4.3 Conductor Grounding. Bond and ground all stringing equipment, such as reel
stands, trailers, pullers, or tensioners. (See Figure 6 and Table 28.)
7.10.5 Primary Line Installation. Lines should be strung to clear the ground by an
amount not less than that specified in the rules of the NESC. These minimums depend upon
whether the line is above a street (consider its street traffic classification), above a pedestrian way,
or over or near other structures. Wire and guys that are being strung should be kept clear of any
92
MIL-HDBK-1025/10
possible interference with public traffic of any type. Where it is necessary to block traffic
temporarily while wires and guys are being installed, one or more members of the crew should be
assigned to direct traffic.
7.10.5.1 Stringing Primary Line Wires. Stringing by facility personnel will normally be
done by the tension method, since this keeps the conductor clear of energized conductors and
clear of obstacles that might cause surface damage to the wire. Slack stringing may be
appropriate for new short line extensions. In either case lines should be sagged to meet the
requirements of the NESC.
a. In stringing wires, care should be taken not to put kinks into any part of the line. Kinks
reduce the strength of the wire and may result in fallen wires later.
b. Before changing the strains on a pole by adding wires, engineering guidance should be
requested to ensure that the pole will safely stand the altered strain.
7.10.5.2 Clipping in or Tying Primary Line Wires. This involves the transferring of
sagged conductors from their stringing travelers to their permanent insulator positions where they
may either be clamped or tied to insulators.
a. Wires should be securely tied-in at all tie-in type insulators to prevent the possibility of
wires becoming loose at points of support and falling to the ground. Where double arms are
provided, line wires should be well tied-in to insulators on each arm. This applies to pin- and
post-type tie-top insulator work. Clamp-type insulators should have the clamps tightened to meet
the manufacturer's requirements.
b. When it is necessary to connect two parallel circuits at one or more points on the line,
the phase wires should be tested with a potential transformer or other means, to make sure that
the phase wires of one circuit are being connected to the corresponding phase wires of the other
circuit.
c. Care should be taken to see that phase wires are not crossed when turning the vertical
angle on three-phase lines, that is, phase wires should take the same position leaving an angle as
coming into it.
7.10.6 Secondary Line Installation. Secondary lines should be installed to meet line
clearance requirements of the NESC. Lines may be single or triplexed wires. Secondary lines
with insulation should be handled with the care insulated wire requires. Workers should be
particularly careful in stringing secondary services, to avoid any undue hazard in close proximity
to primary lines. Locations where the service wires might fall across conductors of a higher
voltage are not permitted.
93
MIL-HDBK-1025/10
7.10.6.1 Stringing Secondary Line Wires. Before stringing secondary wires, nearby or
adjacent energized lines should be de-energized and grounded. As an exception, service wires
may be installed near overhead energized lines provided the following operations are carried out
in the following order.
a. Connect service wires to the building; attach a handline to the other end of each wire
and carefully raise the wire to its position on the pole; and then attach service wires to the bracket
or crossarm.
b. While these operations are being performed, workers should wear rubber gloves and
use insulation to prevent shock from unintentional contact between the service wires and the
primary lines.
c. Personnel on the ground should not attempt to install meters or other secondary
connections while these operations are being performed.
7.10.7 Removing Lines. Removing or salvaging wires requires the same general
precautions as stringing wires. However, where practicable, the wire to be removed should be
pulled out and laid flat on the ground before any attempt is made to coil the wire by hand or on a
nonpower-driven reel.
Note
a. Lines which are being cut or rearranged should not be allowed to sag on, or be blown
against other electric power lines, signal lines, signal equipment, metal sheaths of cables, metal
pipes, ground wires, metal fixtures on poles, guy wires, and span wires.
b. Wires which have been cut, or which are being rearranged, should not be allowed to
fall near or on a roadway where there is danger to traffic. Where it is impossible to keep these
wires clear of the roadway by at least 3 meters (10 feet) or more, (depending upon the voltage of
the adjacent lines) all traffic should be blocked. All persons working on lower levels of poles,
94
MIL-HDBK-1025/10
where cutting is taking place, and all personnel on the ground should be notified well in advance
of the cutting so that they may stand clear.
7.10.8 Guying
Note
a. When insulators are used they should be connected into the guy wire line before the
guy wire is set in place. In new work, guys should generally be installed before line wires are
strung. In reconstruction work, guys should be installed before any changes are made in the line
wires and care should be taken not to place excessive pull on the pole and wires already in
position.
b. Guys should be installed so that there is minimal interference with the climbing space
and guys should clear all energized wires.
c. Guy strain insulators should be provided, wherever necessary, to secure the required
amount of insulation in accordance with applicable codes.
d. Guys should be installed to the correct tension. Where necessary, a guy hook may be
used to prevent the guy from slipping down the pole. These hooks should be so located that they
do not interfere with climbing and so placed that they will not be used as steps. Where guys are
liable to cut into the surface of a pole, the pole should be protected by a guy plate at the point
where the guy is attached. The plate should be well secured to the pole to prevent the possibility
of injury to a worker climbing up or down the pole.
e. All guys should be installed so that they do not interfere with street or highway traffic.
Guys located near streets, or highways, should be equipped with traffic guards. Traffic guards are
sometimes called "anchor shields". Guy guards (traffic shields or anchor shields) should be
yellow.
f. Guy wires should be installed so that they will not rub against messenger or signal
cables.
g. Guy wire containing snarls or kinks should not be used for line work. It is preferable
to use guy wires of the correct length to avoid unnecessary splices.
95
MIL-HDBK-1025/10
7.10.8.2 Removal of Guys. Before guys can be removed, the condition of the pole should
be determined. If the pole is weak, it should be securely braced before any changes in pole strains
are made.
a. Where the removal of guys from a pole will change the strain and present a dangerous
condition, the pole should be braced temporarily to make such a changed condition safe.
b. Where it is not possible to install side guys, poles may need to be braced to be
self-supporting. The pole bracing should be installed so that it will not interfere with climbing or
with street or highway traffic. Pole braced guys should not be used on poles which will be
climbed.
7.10.9 Insulators. Pick up insulators by their tops to avoid cutting gloves or hands on
insulator petticoats. Do not screw down insulators too tightly because their tops may break off,
cutting gloves or hands.
96
MIL-HDBK-1025/10
7.11.4 Climbing Space. Maintain safe access by hanging streetlighting fixtures clear of
the climbing space. All bolts, lag screws, and other hardware used in securing the fixtures will be
carefully trimmed.
7.11.5 Time Switches. When winding time switches, or working on automatic time
switches, workers should not trip the switch "on" without first pulling the transformer disconnects
or making sure that streetlighting circuits will not be energized. On time clocks with medium-
voltage connections, workers should always wear rubber gloves in winding, resetting, and
otherwise maintaining the clock.
7.12.1 Aerial Surge Arresters. Check that the permanent ground connection is intact
before any work is done. Do not climb or strap off to surge arresters. Wear eye protection when
connecting, disconnecting, or discharging surge arresters.
7.12.2 Aerial Switches and Fuses. The maintenance of switches and fuses may require
temporary line modifications to permit repairs where service continuity needs to be maintained.
Both sides of fuses should be de-energized in order for repair work to proceed. Engineering
guidance is required in preparing a step-by-step modification procedure.
7.12.4 Aerial Power Transformers and Voltage Regulators. Check poles and
crossarms before installing a transformer or regulator on an existing pole. Consider that the
following transformer requirements apply to regulators where applicable. Only qualified
personnel should climb poles to fuse, inspect, and test transformers and equipment. When
97
MIL-HDBK-1025/10
transformers are installed or replaced, their secondaries should be checked for voltage and phase
rotation when necessary. When distribution transformers are installed and before they are
energized, the ground connections should be made to the case, secondary neutral, and then to the
primary neutral when used, in the order named.
7.12.4.1 Aerial Energized Work. Except for testing, replacement of fuses, and
switching, work on energized pole-mounted transformers and lines is prohibited.
a. All frames and tackles used in erecting pole-type transformers should be carefully
inspected each time before use. Defects should be repaired before the frames and tackles are
used.
b. Wherever possible, junction poles, subsidiary poles, and streetlighting poles should not
be used as transformer poles. When it is necessary to install transformers on junction, subsidiary,
or streetlighting poles, take care to maintain proper climbing space and to avoid crowding of
wires and equipment.
c. Transformers should be installed only on poles strong enough to carry their weight.
Transformer poles should be straight and, where necessary, guyed to prevent leaning or raking of
the pole after the transformer is hung.
d. When transformers are raised or lowered, all crew members should stand clear and
traffic should be detoured if necessary. In congested traffic, the pole space should be roped off.
Personnel on the pole should place themselves on the opposite side from that on which the
transformer is being raised or lowered. Pole steps and other obstructions in the path of
ascent/descent of large transformers should be removed.
e. When transformers are installed, the pole climbing space should be carefully maintained
so that it will not be necessary for climbing workers to come too close to the transformer case.
7.12.4.3 Aerial Connection. Pole-type transformers should not be installed until they are
supplied with a sufficient amount of good quality oil.
98
MIL-HDBK-1025/10
b. Rubber gloves or hot sticks should be used when installing a pole-type transformer.
First connect the primary leads from the transformer to the primary cutouts; second, make sure
that secondary leads from the transformer are in the clear; third, make connections from cutouts
to primary line; fourth, close primary cutouts; fifth, make polarity tests on secondaries and
connect permanently. When removing transformers, open cutouts and disconnect secondaries to
prevent danger of "backfeed".
c. Where one or more transformers feed into a common secondary or are paralleled on
the low-voltage side, caution should be exercised in re-fusing, as the higher voltage terminals will
be energized by stepping up the secondary voltage that is supplied by the other transformer.
b. When opening transformers, do not use lighted matches or open flames of any kind.
7.12.4.5 Aerial Fusing. When installing fuses, workers should be careful to avoid contact
with any live lines, or with any grounded surfaces (grounded lines, the casings of grounded
transformers, streetlighting fixtures, signal lines, signal equipment, the metal sheathing of cables,
metal conduits, span wires, and guy wires).
a. Before installing fuses in new cutouts, replacing fuses, or opening disconnects, workers
should protect their eyes by wearing goggles and faceshields. They should not use their arms to
protect their eyes and faces from any flashes or arcs that may occur. It is mandatory for the
workers to wear rubber gloves or to use a "hot stick" as appropriate to the voltage level.
Workers should secure themselves to the pole with their safety harnesses.
b. When fuses are taken out of the circuit they should be removed entirely from the fuse
enclosures or cutouts.
c. In phasing out a transformer or in testing it for polarity, small size fuses should
preferably be used.
7.12.4.6 Aerial Service Connections. Do not string service wires from a transformer
pole if it is at all possible to install them at some other location. Service wires should never be
installed on transformer poles, unless a minimum separation meeting code requirements can be
maintained between the service wires and the energized primary conductors or apparatus.
99
MIL-HDBK-1025/10
a. Two workers should be used in stringing services from a transformer pole where
primary jumpers energized at 5,000 volts or more extend below the secondary wires.
b. When a worker is making connections to secondary buses, the neutral wire should be
connected first and energized wires connected last. The procedure should be reversed when
disconnecting services.
Note
WARNING
7.13.2 Tree Trimming Public Safety. Erect suitable signs and barriers to prevent the
public from passing under trees in which personnel are working and to prevent stumbling over
brush on the ground. Brush should not be piled on sidewalks nor left on streets and highways
overnight.
7.13.3 Tree Trimming Tool Safety. Raise and lower tools with a handline. Only saws
and pruning knives or shears are used for cutting limbs. Do not carry unnecessary tools up the
tree. Tools should not be hung or stored on tree limbs.
100
MIL-HDBK-1025/10
WARNING
Be aware that lines may not always be de-energized for tree trimming
operations. Review the rules for live-line safety and for climbing and
working on a pole especially in regard to being knowledgeable of the
energized lines in the area and the relevant dangers. Workers in trees
should use harnesses and safety straps. When working near energized
lines, arrange your safety line so that a slip or fall will carry you away
from the energized lines.
WARNING
7.13.5.1 Tree Climbers. If tree climbers are used, ensure the equipment is approved for
the bark thickness of the tree being climbed. Never use pole climbers.
a. Use a harness and safety strap or life line. Place the strap around a tree limb of
sufficient size to hold the worker's weight, but never around the tree limb being cut.
b. Do not stand on tree limbs too small to support your weight. Extreme care should be
exercised when working in trees that have brittle wood.
7.13.5.2 Tree Work. Before felling trees inspect tools to be used (such as ropes, tackle,
ladders, and chain saws) to ensure they are in proper condition.
a. Place signs warning pedestrian and vehicular traffic of the danger from work being
performed. Station flagmen where necessary.
b. Inspect each tree for possible dangers (conductors and fences) in the line of fall. Have
energized conductors de-energized if possible.
101
MIL-HDBK-1025/10
c. Check each tree for dead or broken tree limbs when climbing. Remove unsound tree
limbs during the climb.
d. Lower cut-off tree limbs with a rope. Falling tree limbs can cause injury and property
damage.
e. Trees greater than 7.5 meters (25 feet) tall and 200 millimeters (8 inches) in trunk
diameter should have ropes attached before felling. Assign workers to the ropes to guide the tree
as it falls.
WARNING
b. The idle speed will be adjusted so that the chain does not move when the engine is
idling.
c. The operator should be sure of his/her footing before beginning cutting operations.
d. The operator should hold the saw with both hands during all cutting operations. Grip
the chain saw properly. Place one hand on the top handle with the thumb curled under the handle.
Place the other hand on the control handle.
e. The operator should stand to the side of the chain saw, not directly behind it, to keep
the body away from the path of the guide bar if kickback occurs. Be alert to conditions that can
cause the chain saw to kick back. Kickback occurs when a solid object (such as a tree limb above
the cutting area) contacts the chain at the guide bar nose. This causes the saw to be thrown
violently up and back toward the operator.
102
MIL-HDBK-1025/10
f. The chain saw should never be used to cut above the operator's shoulder height.
g. The operator should shut off the saw when carrying it over slippery surfaces, through
heavy brush, and when adjacent to personnel. The saw may be carried running (idle speed) for
short distances of less than 15 meters (50 feet) as long as it is carried to prevent contact with the
chain or muffler.
h. Never operate a chain saw when physically tired or under the influence of alcohol,
medication, or other drugs.
i. When felling a tree clear a path of retreat while assuring that the fall does not damage
anything.
7.13.6.2 Chain Saws. Chain saws should be kept clean and sharp at all times, and kept in
sound mechanical condition with all guards, spark arresters, mufflers, handles, and other items
properly installed and adjusted. Observe these equipment precautions
a. Fuel for chain saws should be stored in approved vented containers that are marked to
show their contents. Never store the fuel near flammable materials. Keep the containers clean.
Always wipe the spout clean before filling the chain-saw tank. Filtering the fuel mixture will
ensure continued smooth engine operation.
b. Make sure that a proper mixture of fuel (gasoline and oil) is used. Check the fuel tank
and chain oiling reservoir for proper levels before use. The filler caps for the fuel tank and chain
oiling reservoir should be clearly marked and securely attached during operation and storage.
c. The chain saw should not be started within 3 meters (10 feet) of a fuel container.
d. The chain saw should not be fueled while running, hot, or near an open flame.
a. Cutters felling heavy brush or small trees should give sufficient warning to other
personnel. Never work so close that one worker could injure another with a swinging ax or hook.
b. Brush chippers should be operated only if authorized and by standing to the side of the
chipper chute while feeding the butt end of brush into the chipper first. Use the automatic shut-
off/stop control at the operator's station in an emergency.
103
MIL-HDBK-1025/10
c. Tools such as saws, axes, bush hooks, pruning shears, scythe blades, and pitch forks,
should not be hung in bushes or small trees nor stored hidden from easy view of other workers.
d. Personnel assigned to remove or pile brush should stay a safe distance behind workers
using cutting tools.
e. When burning brush, be careful at all times to see that the fire and sparks are under
control. Cover hot ash piles with dirt or douse them with water. Obey local laws concerning
open fires. The burning of poison ivy, poison oak, and poison sumac is prohibited. Smoke from
burning these plants is very toxic; even the windward side of the fires may not be safe.
g. Workers should always be on the alert for snakes when cutting right-of-way. A
standard snake bite kit should be carried on every such job.
104
MIL-HDBK-1025/10
8.1 Underground Work. Comply with the requirements of OSHA standard 29 CFR
1926.269(t), “Underground Electrical Installations.” Underground work may pose unique safety
problems where the work is accessible by the public or where the work has to be done in a
confined space.
8.2 Underground Work Area Protection. Work area protection is the safeguarding
or protecting of pedestrians, motorists, facility workers, and equipment by the use of barriers,
warning signs, lights, flags, traffic cones, barricade rope, and flagmen. Protection is required for
approaches to work areas, excavations, open manholes, and parked equipment. An approved fire
extinguisher in good operating condition and immediately accessible for underground work is
mandatory.
8.2.1 Underground Work Area Protection Methods. Work area protection methods
should provide safety for workers, equipment, and the public without excessively impeding public
traffic.
a. During any period in which apparatus needs to be left open and energized, a suitable
enclosure should be erected around the apparatus, or a qualified worker should be stationed at the
location, to ensure the safety of the public.
b. All temporary cable installations should be made in a manner providing safety for
workers and the public.
8.2.2 Impact of Vehicular Traffic Flow. The amount and speed of the traffic will
influence the work planning. Where work will require excavation in roads and highways, the
appropriate traffic authority should be consulted in order to maintain safe traffic flow. The public
should be warned in advance, then regulated and guided safely through or around the work area.
8.2.3 Work Space Considerations. The extent of the work and the lineup of traffic
will effect scheduling, which should be done to cause the least interference to traffic and, minimize
the possibility of accidents. Good housekeeping in the storage and equipment space necessary for
the work should always be an ongoing concern but especially wherever it impinges on public
right-of-ways. It is of the utmost importance that the work area be properly identified and that
warning devices clearly convey the appropriate message to the traveling public, well in advance of
arrival at the work area. This same good housekeeping applies to protection of workers.
8.2.4 Barricades and Warning Precautions. Traffic control requires the use of
barricades and warning precautions.
105
MIL-HDBK-1025/10
8.2.4.1 Devices. Only those signs, standards, barricades, flags, and cones that conform
to state or local codes will be used. All state and local traffic codes will be followed when
providing work area protection.
b. Warning devices and equipment will be removed as soon as the hazard is eliminated.
c. Warning devices and equipment not in use will be stored in a proper manner or
removed from the work area.
8.2.4.2 Flagmen. Flagmen or other appropriate traffic controls will be used whenever
there is any doubt that the use of signs, signals, and barricades is ineffective.
a. Flagmen will wear a red or orange warning vest or garment. Warning garments worn
at night will be of a reflectorized material.
b. Flagmen using hand signaling equipment will ensure signals provide sufficient warning
to protect themselves and the work site. Signal flags will be red and at least 60 centimeters (24
inches) square. Sign paddles (Stop and Slow) will be on a 1.8-meter (6-foot) staff. In periods of
darkness or reduced visibility, red lights will be used.
d. Flagmen will ensure that they can fully observe the operation and will guide vehicular
traffic in such a manner as to minimize the possibility of accidents or injury.
e. When flagmen are used at both ends of a job site, reliable communications or
prearranged signals will be used to insure proper traffic flow.
g. Flagmen will give positive, direct signals that leave no doubt as to their meaning.
106
MIL-HDBK-1025/10
8.2.4.4 Caution and Danger Signs. The following are approved signs:
Note
a. During the time that manholes or vaults at the sidewalk or street level are open,
suitable barricades, traffic cones, warning signs, flags, and lights will be used and maintained.
b. When working in vehicular traffic areas manholes, traffic cones should be used to guide
traffic around the danger area. Great care should be exercised not to obstruct traffic. In addition,
a blinking light may be used on the traffic side of the hole, as well as sawhorse type barricades
around the hole.
c. For sidewalk manholes and vaults, the barricades should provide pedestrians and
onlookers positive protection against falling over material or into the manhole. At night all open
manholes should be outlined with either flashing or nonflashing lights.
a. All equipment and materials, stored where pedestrian or vehicular traffic might be
endangered, should be marked with red flags by day and red lights by night, or both. Do not store
equipment or materials where they will obstruct fire alarm boxes, hydrants, or fire apparatus.
107
MIL-HDBK-1025/10
b. Keep tools, stones, and dirt away from the edge of a trench. Excavated material
removed from trenches in streets should be kept on the traffic side of trenches, whenever possible,
until it can be used for fill or removed.
c. Carefully refill excavations until such time as permanent paving can be done. See that
all refilling is well tamped.
d. Provide ditching machines with suitable walkways, footboards, railings, and proper
safeguards over gears, chains, and other moving parts. Do not stand near digging buckets while
the machine is in operation.
e. Protect all open holes along streets and highways or other frequented places by suitable
covers.
f. In excavations which workers may be required to enter, excavated or other material will
be kept at least 0.6 meters (2 feet) or more from the edge of the excavation.
g. When workers are required to be in trenches 1.2 meters (4 feet) deep or more, at least
two separate and adequate means of exit, such as ladders or steps, will be provided and located
requiring no more than 7.5 meters (25 feet) of lateral travel.
h. Sides of trenches 1.5 meters (5 feet) or more in depth will be shored, sloped, or
otherwise adequately supported to protect those working within them.
i. Suitable gloves will be worn when using any equipment or tools to excavate, expose, or
handle direct-burial cables.
Note
108
MIL-HDBK-1025/10
WARNING
a. Wire rope will not be used to pull cable in a duct already occupied by conductors.
b. A nonmetallic duct fishing wire or device will be used when fishing ducts containing
energized conductors.
c. Ducts will always be fished in the direction that presents the least hazard. A worker
will be stationed at each end when required.
d. Avoid parking tool carts and reels on inclined streets. Where this cannot be avoided,
equipment should be placed at a slight angle to the curb so that the curb serves as a chock.
Chock all wheels with blocks or other suitable items and install a well-fastened upright brace at
both the front and rear of the vehicle. Where more than one reel is parked at the same location,
lag the reels together. Place and fasten chock blocks and braces so that they cannot be easily
dislodged.
8.3.1 Locating Buried Facilities. Use area utility maps to locate existing utilities as
accurately as possible.
109
MIL-HDBK-1025/10
a. Probe rods or bars will not be used to locate any underground direct-burial cables.
c. All exposed cables in a work area will be protected against damage by boards or other
nonconductive materials. When it is necessary to weld adjacent to cables, suitable nonflammable
protective material will be utilized.
d. Under no conditions will workers stand, sit, kneel, or lean on unprotected direct-burial
cables.
CAUTION
8.3.4 Handling Damage to Existing Utility Lines. If any existing utility lines are
damaged then certain steps should be taken dependent upon the type of line.
a. If electric cables are damaged the facility should de-energize the damaged line and take
immediate steps to repair it.
b. Environmentally hazardous lines, such as sewer, fuel, and oil, will be handled in
accordance with the applicable health and safety hazard requirements. Environmental cleanup will
be initiated as soon as possible.
c. If health and safety hazard lines such as gas, steam, or hot water are damaged, the hole
will be left open until any utility line flow has been dissipated safely. All possible sources will be
shut off. Any workers or residents of the area will be warned, when necessary, and the public
will be kept out of the area. The local fire department and the appropriate maintenance facility
will be notified immediately.
WARNING
Extreme care will be taken to eliminate the possibility of igniting any escaping gas.
110
MIL-HDBK-1025/10
d. Other lines, such as communication, water, or storm drainage, will be repaired as soon
as possible by the appropriate maintenance department.
WARNING
The major reason for accidents and damages caused by excavation work
results from a lack of knowledge on the location of existing underground
utilities. Preplanning will locate any such obstructions and ensure that
correct excavation and backfilling procedures are followed in existing
underground utility locations.
8.4.1 Preplanning of the Excavation Project. The most important step is to identify
underground utilities.
8.4.2 All Projects Preplanning. Pre-mark proposed excavation area with white paint
prior to notifying the utilities locating service.
a. Obtain the work order or excavation package and document the location request
number. Acquire and retain the sketch of the utility location if supplied by the facility owner.
b. Make sure request numbers are valid and that customer information is correct.
c. If there is a “high priority” facility line in the excavation area, make arrangements for
the utility locator to be on the job site during the excavation (that is, high pressure gas, fiber optic,
medium voltage electric, major pipe and water lines). If the utility locator or facility owner
refuses to be present, then document this response on the work order or excavation package.
d. Ensure that all known underground utilities owners have been contacted.
8.4.4 On the Job Site Procedures. Once on the job site, begin job preparation by
reviewing the list of underground utility/facility owners that are in your excavation area and make
111
MIL-HDBK-1025/10
sure that location marks for all facilities are present. Provide a color chart listing each utility with
a different color if necessary to ensure all facilities have been located. Have color charts in the
hands of all excavators to ensure all known facilities have been shown.
a. If a “high priority” facility is in the excavation area, make sure the locator is on site. If
not, consult the color chart for the facility contact numbers and call the facility company and
document the response.
b. Account for all utility connections to houses or buildings before you excavate. You
should be able to see them above ground or marked on the ground.
c. Identify or locate all private facilities that have not already been located. This includes
propane and private lines, sprinklers, and other such lines. Look for sewer vents on the roof of
the house, look for sprinkler heads, turn on the system if necessary. Look for physical evidence
that facilities have not been located.
d. Sketch the location and document the depth of all public and private facilities on your
work order for future reference. If no sketch exists of all other facilities, draw a sketch of marks
with measurements of fixed objects if possible for future reference.
e. Expose all facilities that you will be crossing. When possible, all major facilities (that
is, high pressure gas, fiber optic, medium voltage electric, major pipe and water lines) should be
exposed every 30 meters (100 feet) if parallel within 1.5 meters (5 feet) of the excavation area.
f. If there are no utility locations, if marks are incomplete, or if exposing indicates utility
locations are not accurate, DO NOT DIG. Contact the facility owner to complete the utility
location.
g. Once you have verified the location of all lines and you have completed the Job Check
List, you can begin to excavate. Remember to document the sketch of your excavation site
before you start excavating.
WARNING
a. Hand dig within 1.5 meters (5 feet) of any pedestal, closure, riser guard, pole (with
riser), meter, or other structure. Hand dig within 0.6 meters (2 feet) of any and all other utility
location marks.
112
MIL-HDBK-1025/10
b. If it is necessary to use mechanical equipment within 0.6 meters (2 feet) of a mark you
should expose the line first.
c. If you are paralleling a line, expose every 30 meters (100 feet) to verify the location
and depth of the line. If the utility location is not accurate, contact the facility owner immediately.
d. If using a boring machine, bore away from all facilities. If it is necessary to cross a
facility, expose the line to verify location and depth. This may require changing the bore route or
depth to avoid a facility. Contact your supervisor to approve route changes.
e. Never place excavated dirt or street plates on top of utility location marks. Keep
marks visible and fresh at all times.
Note
a. All lines exposed during excavation should be supported to prevent stretching, kinking,
or other damage.
b. “Shade” all lines, meaning clean, good fill dirt placed around the lines to prevent
possible damage.
c. All backfill dirt should be “clean fill” free of large rocks, sharp objects, and large
chunks of hard packed dirt or clay.
d. No cable or personal trash and no abandoned lines, or pieces of lines, may be backfilled
into the trench.
a. If the damage involves a potential risk to life, health or significant property damage, the
excavator should call 911 or the local emergency response number.
b. All damages, including kinking or sheath damage, however slight, should be reported
immediately to a supervisor and to the facility owner or operator.
113
MIL-HDBK-1025/10
c. Photographs should be taken and reports completed to help document the damage and
assist in resolving any claim that may be filed.
d. If a water line, other than a main is damaged, you should attempt to stop the flow of
water if possible.
e. If a gas or power line is damaged, it may be necessary to leave the area immediately
and notify others in the area. REMEMBER, SAFETY FIRST!!! FOLLOW LOCAL SAFETY
STANDARDS AND PROCEDURES.
8.4.8 Accountability for Excavator Error. Obtain and learn the laws and regulations
that pertain to excavating in your city or state. Everyone should incorporate these procedures
into their daily routine. By utilizing these procedures, it will increase your productivity and
efficiency, not to mention the obvious safety benefits. Consider disciplinary action, suspension, or
termination in any of the following situations.
b. Excavating, including hand digging, without utility locations for any or all facilities or
private lines.
WARNING
Before entering the manhole test for oxygen deficiency and dangerous
gases. If there is an oxygen deficiency, or if any toxic or combustible gas
is entering the manhole, provide adequate ventilation while there are
workers in these structures. Smoking is not permitted in manholes.
8.5.1 Removing a Manhole Cover. Two persons, each with a manhole cover hook,
may be required to remove a cover. They should lift the cover with the leg and arm muscles, and
114
MIL-HDBK-1025/10
with their feet placed so that they will be clear if the cover should be accidentally dropped. Figure
11 shows the methods and steps for removing a circular manhole cover.
WARNING
A manhole cover may weigh from 90 to 160 kilograms (200 to 350 pounds).
NOTE
1. FEET ALWAYS IN
THE CLEAR
2. BOTH HANDS
USED
THIS HOOK LIFTS COVER
3. WEIGHT
LEVEL WITH FRAME
KEEP FEET CLEAR SHARED BY BOTH PERSONS
THIS PULL CARRIES COVER SLIGHTLY THIS PULL SIMPLY UNSEATS
MORE THAN HALFWAY OFF FRAME COVER OFF FRAME
STEP 4 STEP 5
Figure 11
Steps in Removing a Manhole Cover
a. If the manhole cover does not lift readily, first check to be sure the cover is not secured
by a locking device. If a locking device is not holding the manhole cover, loosen the cover by
placing a block of wood on the cover near the rim and striking the wood with a heavy hammer.
Insert a manhole hook into one of the manhole cover holes. Pry the cover while the block of
wood is being struck at several different points around the circumference of the cover.
b. If snow, ice, or other surface conditions cause insecure footing around the manhole
cover, either clear the working area with a shovel or broom, or spread sand or other suitable
material around the cover to ensure firm footing. Do not strike the manhole cover with a steel or
iron tool. Use a hardened bronze cold chisel to remove ice from a cover. A bronze cold chisel
115
MIL-HDBK-1025/10
will not produce sparks in striking the manhole cover Do not use an open flame or salt to thaw
ice around or over the cover. An open flame may cause an explosion if a combustible gas mixture
is present in the manhole. A salt solution seeping into the manhole may contribute to cable
corrosion. Make test holes in the ice to locate the edge of the manhole cover.
c. A line or cable locator is useful in finding manhole cover locations when records are
inadequate or when marking points are covered with ice and snow. If the exact location of the
manhole is not known, a small channel may be cut from the outer edge of the general location to
the center of the area where the cover should be. If the manhole cover is icebound, use enough
hot water to melt the ice around the edge of the cover.
d. Do not leave a manhole cover in a location where it will present a hazard. If the cover
cannot be left near the manhole opening, skid the cover to a safe location. If necessary, place a
warning device near the removed cover.
e. Before removing a manhole cover, mark the cover and the frame with a piece of chalk
so the manhole cover may be replaced in its original position. Improper alignment of the cover
within the frame may cause considerable noise when vehicles cross over the covers. When the
noise condition does exist, place a thin layer of oakum (or similar material) in the cover seat of the
frame.
f. In a traffic area, the manhole cover is removed in a direction that will prevent personnel
from falling into the path of traffic should the manhole cover hook slip during the cover removal.
The removal position should permit observation of oncoming traffic. When possible, insert
manhole cover hooks in the hook holes on the side away from moving traffic. Place the covers of
opened manholes on the side away from traffic, when conditions permit. In case of two section
covers, place one section on each side of the opening.
g. When this is not practical, insert the manhole cover hooks in the holes that permit the
cover to be moved in the direction of traffic. Keep the oncoming traffic under careful
observation.
h. Replace manhole covers with the same care as used for removing them. Be careful that
manhole covers are properly seated when replaced. The bearing surfaces should be free from dirt
or ice which might prevent them from fitting properly.
116
MIL-HDBK-1025/10
WARNING
The structure should be tested to ensure that the atmosphere is safe for
workers. Entering a manhole with an oxygen deficiency can cause
sudden unconsciousness and death by hypoxia (blood starvation).
Manholes containing less than 19.5 percent oxygen are not to be entered
without a supplemental oxygen supply.
WARNING
117
MIL-HDBK-1025/10
a. Oxygen deficiency tests should be performed with an approved and calibrated oxygen
deficiency indicator. Operation of the indicator instrument should be in accordance with the
manufacturer's instructions.
b. For the detection of "toxic gases," one of the simple effective colormetric detectors
(color changes to indicate concentration) may be used. Hydrogen sulfide can be detected at
concentrations as low as one part in 1,000,000. These detectors can be obtained commercially,
and a universal test kit is available which will detect concentrations of carbon monoxide, hydrogen
sulfide, and numerous other gases. An approved portable unit should be used to measure the
amount of combustible and toxic gases in the manhole atmosphere.
WARNING
Never enter a manhole until test results indicate that the manhole is free
of combustible or toxic gases.
a. If tests made upon removing the manhole cover indicate that the atmosphere is
satisfactory, the manhole or vault may be entered and worked in. Additional tests should be made
when each crew begins work; the test interval should not exceed 8 hours. When the manhole is
covered with a tent or tarpaulin, the test interval should not exceed 2 hours. Place the tent or
tarpaulin so that an opening is left in the covering for ventilation.
b. If more than the allowable trace of gas is found on the initial test, ventilate the manhole
or vault with a power blower for a minimum of 10 minutes, then make a second test with the
blower running. If the test is satisfactory, the manhole or vault may be entered. Make this test
away from the direct blast of the blower. If gas is again found on the second test, continue to
ventilate the manhole with a power blower until the test is satisfactory.
c. Work can then be started in the manhole, provided adequate power blower ventilation
is continued. There should be enough ventilation to hold the quantity of gas in the manhole to an
allowable value until the work has been completed and the cover is replaced. While working in a
manhole being ventilated with a power blower because of previous gas detection, test the
atmosphere every hour. If the blower stops, leave the manhole at once and do not re-enter until
ventilation has been restored and the atmosphere test is satisfactory. Operate the blower outside
of a manhole tent or tarpaulin.
118
MIL-HDBK-1025/10
WARNING
Pumping out structure water or removing duct line plugs can allow gas into the structure.
a. After a manhole has been pumped, the removal of the water may permit gas to flow
into the manhole. Make the test just above any open ducts. If a test indicates that gas is entering,
ventilate the manhole.
b. Immediately upon the removal of the duct plugs, make a test just above the opened
duct. If gas is entering, ventilate the manhole.
WARNING
8.5.3 Ventilation of Underground Structures. There are three methods that can be
used to ventilate a structure. They are the forced air, natural, and sail methods.
8.5.3.1 Forced Air. The forced air method consists of a power blower, blowing air into
the manhole. The blower hose is placed into and on the bottom of the manhole, forcing fresh air
to circulate and oxygen-deficient air to be forced out. This is the best method of ventilating a
manhole.
8.5.3.2 Natural Method. This method consists of taking the manhole cover off and
letting the internal air escape as much as it can. This method of venting a manhole is the least
effective because a gas heavier than air could remain in the bottom of the manhole. Use this
method of venting a manhole only as an emergency measure.
8.5.3.3 Sail Method. The sail method (figure 12), ventilates the manhole by using the
wind. A piece of plywood or some other material is placed over the manhole. The edge of the
plywood facing the wind is lifted up until the plywood forms about a 45 degree angle with the
manhole opening. The wind enters the manhole, forcing possible contaminated air out of the
manhole.
119
MIL-HDBK-1025/10
Figure 12
Sail Method of Manhole Ventilation
8.6.1 General Inside Structure Safety. All work should be done in a manner that
observes the following precautions
c. A ladder will always be used when entering or leaving a manhole or vault. Climbing
into or out of manholes or vaults by stepping on cables or cable supports is forbidden. Manhole
ladders, when not in use, should be placed so as not to be a hazard to workers, pedestrians, or
vehicular traffic.
d. Use only flashlights or facility approved lighting units for illumination in manholes.
e. Tool handling should be done in a manner that protects the workers and work area.
Always place tools or materials a safe distance from manhole openings, where they will not cause
120
MIL-HDBK-1025/10
a stumbling hazard or come in contact with energized conductors or equipment. Do not throw
tools or materials into or out of manholes. Use canvas buckets or hand lines for lowering tools or
equipment into and removing them from manholes. Warn workers before lowering tools. Always
provide a windless handcrank subsurface worker rescue or an approved retracting lifeline system.
f. Before starting work, an inspection should be made to determine if there are any
dangerous conditions such as burnt or cut cables or loose or defective ladders. Use of portable
ladders is preferred. Ladders in manholes, if provided, may have rusted and become unsafe.
Before using open flames in manholes or excavations where combustible gases or liquids may be
present, such as near gasoline service stations, the atmosphere should be again retested and found
safe or cleared of the combustible gases or liquids. When open flames need to be used in
manholes, extra precautions should be taken to provide adequate ventilation.
WARNING
The worker should be familiar with the system before proceeding to any
necessary tagging of cable and equipment. Every possible precaution
will be exercised to correct identity (voltage, circuit, and phase) of cable
or apparatus to be worked upon.
a. Be sure cables are properly identified before beginning any work. All cables should be
tagged, but in the event that they are not or that tags have become illegible or lost, obtain specific
instructions rather than take a chance. Retagging is required before work can begin.
121
MIL-HDBK-1025/10
WARNING
WARNING
The item will be grounded from all possible sources of power (including
transformer secondary backfeed) and positively traced from the grounded
point to the work location.
WARNING
8.6.4.1 Underground De-energized Work. All cable and apparatus should be tagged
properly.
122
MIL-HDBK-1025/10
a. The secondary voltage of any transformer fed from a de-energized feeder cable should
be checked. The cable should be grounded on each side of the work location.
b. Neutral conductors should not be opened without the prior installation of suitable
bypass conductors.
c. Avoid moving energized underground cables. If cables must be moved, they will be
moved with extreme care to avoid damage to the cable insulation. Moving will be done only at
the discretion of the foreman in charge. Lead-sheathed underground cables will be moved only
when approved by the supervisor. Prior to moving energized electric underground cables, they
will be examined for any defects that might result in failure if the cable is moved. No energized
cable may be moved where such movement requires changing bends. All energized cables will be
handled with rubber gloves or hot-line tools as appropriate to the voltage level.
WARNING
b. The tags on the feeder cable and equipment in the vault or manhole bear the same
number as shown on single line drawings.
c. Network protectors are in the open position or, in the case of radial transformers,
which the secondary fuses have been removed and transformer secondaries are dead.
123
MIL-HDBK-1025/10
WARNING
a. Always wear rubber gloves when sawing into a cable or removing the sheathing.
Install a metallic jumper between two sides of the location where a cable sheath is to be removed
or cut.
b. When a medium-voltage cable is to be cut, a short section of the shielding, if any, will
be removed completely from around the cable. Tests will be made with two statiscopes or other
approved testing devices, to determine whether or not the cable is de-energized. If no indication
of a live cable is obtained, the worker may proceed with the work.
c. When opening a splice in a medium-voltage cable, the sleeve over the splice will be cut
completely around near the splice and then cut lengthwise and removed. No effort will be made
to remove the compound. Workers will then test over each side of the conductor with two
statiscopes or other approved testing devices. If no indication of a live cable is obtained, the
compound will be removed. If shielding tape is then encountered, it will be removed and another
test made over each side of the conductor with two statiscopes or other approved testing devices.
If no indication of a live cable is then obtained, the splice will be cut through until the saw touches
one of the conductors. Before sawing further a statiscope test will be made on the blade of the
saw.
d. When cutting or opening splices on low-voltage cables, the same procedure as outlined
above for medium-voltage cables will be followed, except in testing. To determine whether the
cable is energized the insulation will be cut away to the conductor and tested with an approved
tester. On multiple-conductor cables, only one conductor will be cut into a time and tests made
on at least two conductors before proceeding with the work.
124
MIL-HDBK-1025/10
8.7 Heating Materials. Heating materials and equipment used in splicing cable will
be heated in such manner as to prevent any hazard to the those working in manholes or vaults and
to vehicular or pedestrian traffic.
WARNING
Observe the following precautions to protect yourself, others, and the workplace.
a. Gloves will be worn while heating or working with hot insulating compound.
b. Furnaces and tanks containing liquefied petroleum gas, such as butane or propane, will
not be placed in a manhole or vault.
c. Heating pots for solder, oil, or compound will be safely positioned so that the contents
cannot enter the vault or manhole in the event of spillage.
The following work rules apply to the use of torches, furnaces, pots, and
soldering devices. Only workers who are familiar with the use of torches
and furnaces will be allowed to use them.
a. Only approved soldering pots, furnaces, and ladles in good condition will be used.
b. Keep lighted furnaces or torches 1.2 meters (4 feet) or more from manhole openings
wherever practicable and where they will be the least possible hazard to property, workers, and
the public. If necessary to use torches or furnaces in manholes, adequate ventilation should be
provided to support combustion and provide sufficient air for workers.
c. Solder ladles should be heated before use. Be sure that scraps of cold solder are dry
before remelting. Moisture and molten metal should never come in contact with one another
because this will cause a splash of hot metal. Bars or pigs of solder, tools, and ladles should be
heated over the furnaces before being put into a pot of hot solder. (New workers should be
cautioned about this hazard.)
125
MIL-HDBK-1025/10
d. Furnaces should be lighted carefully and guarded with a three-sided windshield at all
times when burning in public places. Never light or burn furnaces in dangerous locations and
never leave them unattended. Lighted or hot torches or furnaces should not be transported in
trucks or other moving vehicles.
e. Always take special care not to splash solder on any person or equipment. Soldering
pots should not be placed on furnaces without a pot guard. Never attempt to do soldering unless
a fellow worker is stationed on the ground as a guard. If necessary, rope off a safe distance.
Before lowering hot solder or compound into a manhole, warn those in the manholes to stand
clear. Do not lower anything until given instructions from below to do so.
f. If compound kettles have no breathers, punch holes through the top crust of the
compound to the bottom before heating so that air and moisture can escape. Heat the compound
slowly.
h. Place compound kettles on the hoods or plates provided and never directly on top of
the furnaces.
126
MIL-HDBK-1025/10
Table 39
Shore-to-Ship Electrical Connect Responsibilities
I. Ships logistic requirements sent to shore before docking by SHIPS EO. (Refer to par.
9.5.2.2.)
II. Shore provision before ship docks by SHORES ES.
A. Laying, inspection, and testing cable assemblies on dock. (Refer to par. 9.7.1.1.)
B. Checking shore receptacles. (Refer to par. 9.7.1.2.)
C. Inserting cable plugs into shore receptacles. (Refer to par. 9.7.1.3.)
III. Shore-to-ship cable rigging after ship docks by SHORES ES. (Refer to par. 9.8.)
IV. Ship’s transfer from ship’s generators to shore electrical power by SHIPS EO. (Refer to
par. 9.9.)
Table 40
Shore-to-Ship Electrical Disconnect Responsibilities
I. Ships transfer from shore electrical power back to the ship’s generator by SHIPS EO.
(Refer to par. 9.10.)
II. Shore provision of disconnecting cable plugs and unrigging and removing cables by
SHORES ES. (Refer to par. 9.11.)
9.2 Ship’s Main Electrical Service Components. The specific safety requirements
given apply to the cable assemblies from the pier’s electrical outlet assemblies (turtlebacks) to the
ship’s electrical bus. There are other components of the shore’s medium-voltage electrical
distribution system which are used to supply substations that in turn supply the pier electrical
127
MIL-HDBK-1025/10
outlet assemblies. The safety requirements for the pier electrical outlet assemblies which supply
line side components are covered by earlier sections. However since they are provided for ships
power in addition to permanent pier electrical loads they are described for a clearer understanding
of the dockside electrical distribution system.
9.2.2 Pier Substations. Substations may consist of above ground substations of the
nonfixed type installed on the top of a pier or units of the fixed type installed in vaults located
under the pier. Fixed substations are fed by primary cables installed in duct lines. Nonfixed
substations are skid-mounted and fed from a shore installation substation consisting of a medium-
voltage disconnect assembly. Nonfixed substations are supplied by primary cable assemblies
installed on the pier and are connected to the electrical distribution system source and the
substation by primary voltage pier coupler plugs and receptacles in electrical connection outlet
assemblies. Both types of substations contain primary switch(es), the step-down transformer, and
secondary circuit breakers supplying the pier electrical outlet assemblies for ship-to-shore power
cables. Pictures A, B, C, and D show these component elements.
9.2.3 Ship-to-Shore Pier Electrical Outlet Assemblies. Ships service is from pier
electrical outlet assemblies which contain multiples of three-pole, 500-ampere receptacles rated
either for 450-volts ships service or 4.16-kV ships service as appropriate to the pier’s ship
electrical service requirement. Receptacles are interlocked with their associated substation
secondary circuit breaker for safety reasons. Pictures E and F show outlet assemblies for 480-volt
and 4.16-kV services respectively.
Note
128
MIL-HDBK-1025/10
129
MIL-HDBK-1025/10
130
MIL-HDBK-1025/10
131
MIL-HDBK-1025/10
132
MIL-HDBK-1025/10
133
MIL-HDBK-1025/10
SYMBOLS
To shore medium-voltage distribution system or to 15-kv disconnect
assembly Skid-mounted substation with pier electrical outlets
Duct line under pier
Substation in below pier vault
Ship’s bus service port
Pier electrical outlet assembly Shore-to-ship cables
SHIP
SHORE
PIER
Figure 13
Shore-to-Ship Portable Power Cable Location Diagram
9.3.2.1 General Electrical System Safety. The maintenance and operation safety
aspects of the medium-voltage distribution system, substations, vaults, and low-voltage cables in
duct lines is covered in previous sections.
134
MIL-HDBK-1025/10
Abbreviations: 12
3 Fused primary disconnect switch
CB Circuit breaker 2
CS Control switch 3
4 Transformer
ET Emergency trip 10 SUBSTATION 11
LR Local remote control 7 5 Main CB with CS and ET pushbutton
6 6 7 7 9 ET pushbutton
10 To vault power
SHIP
Figure 14
Preferred Ship-to-Shore Circuit Arrangement
Note
135
MIL-HDBK-1025/10
SHIP
Figure 15
Procedures in Safely Energizing a Ship From a Shore Electrical Circuit
CAUTION
136
MIL-HDBK-1025/10
Note
WARNING
WARNING
WARNING
The NEC defines ready accessible as capable of being reached quickly for
operation, renewal, or inspections, without requiring those to whom
ready access is requisite to climb over or remove obstacles or to resort to
portable ladders, chairs, or other such devices. Therefore all workers in
vaults need to meet the confined space requirements of Section 8.
137
MIL-HDBK-1025/10
9.4.3.2 Working Space. The NEC defines working space as sufficient access provided
and maintained about all electric equipment to permit ready and safe operation and maintenance
of such equipment.
a. Working space in vaults has been provided in accordance with the NEC requirements
applying at the time the vault was built.
b. As with all safety aspects affecting both the public and workers, safety requirements
have, over the years, become more rigorous.
c. Although NEC current requirements do not apply to vaults built to previous NEC
editions, in line with Naval safety requirements, the NEC current requirements should be
compared by each activity with actual working space provisions.
d. Each activity should evaluate the comparisons as to their effect on workers safety and
provide SOP’s as necessary to assure safe working conditions.
Note
a. The ship’s hull serves as the ground for the ship’s electrical service. A ground
connection between the shore ground and the ship’s ground can result in damaging circulating
currents.
b. Improper matching of phase rotation will result in the ship’s motors operating in the
wrong direction. Connecting two or more power cables to a ship requires that all the same phase
cables be connected together.
c. The number of power cables should meet the ship’s electrical officer’s request that is
based upon the ship’s activity in port. When more than one feeder cable is required, all cables will
be of the same length and size (within plus or minus 10 percent) to minimize unequal load
distribution. Low-voltage receptacles have a power supply capability of 386 kVA. (Per NEC
Table 310-17, 75 degree C for 500 kcm at 450-volts for continuous service or 620 amperes x 450
volts x 1.732 x 0.80 ÷ 1,000 = 386 kVA). Medium-voltage outlets have a power supply
capability of 2075 kVA. (Minimum cable rating is 360 amperes or 360 amperes x 4,160 volts x
1.732 x 0.80 ÷ 1,000 = 2,075 kVA).
138
MIL-HDBK-1025/10
WARNING
Parallel operation of the ship and shore systems may be done only as given below.
a. Parallel operation of the ship generators and the shore power system is prohibited
except for short periods of time to allow for load transfer to or from shore power. Transfer time
should not exceed 10 seconds.
b. Paralleling shore transformers through the ship’s electrical bus without prior activity
approval is a violation of safety practices and may result in circulating currents, overheated cables,
unbalanced loads, and excessive shore circuit current which could damage property and result in
personal injury.
9.5.1 Specialized Shore-to-Ship System Training. Qualifying for this work requires
training that addresses the operation, maintenance, and testing of the power cable/connector
assemblies; the ability to connect cable extensions; and the understanding of cable phasing and
paralleling checking methods. Workers should also be able to lay and protect cables on piers and
to operate cable rigging devices at both the ship’s cable access ports and at the cable storage
areas. They should be familiar with operating the ungrounded electrical connection required to be
compatible with the ship’s electrical system. Workers should be qualified for working on and be
familiar with the safety requirements for medium-voltage distribution systems supplying
substations and electrical power outlet assemblies supplying shore-to-ship electrical power.
Note
139
MIL-HDBK-1025/10
requirement correctly filled in for each specific ship’s service and for each service period. SOP’s
will be distributed to all personnel involved.
9.5.2.2 Specific Organization Requirements. The names of shore personnel and their
responsibilities will be listed. The name of the ship and the docking location will be given. The
ship’s specific requirements as to the following will be noted.
9.5.2.3 Priorities
Note
Determine if there are any unusual job hazards. Identify the power cable
rigging device (boom trucks, cranes, fork lifts) and whether their location
requires structural approval by a facility engineer of their proposed
location. Verify that any construction work will not interfere with power
cable placing and rigging. Determine special safety provisions. (See
picture K.)
140
MIL-HDBK-1025/10
a. Power cable protection may require barricades to protect them from damage. (See
picture L.) Contractor work may require crossing power cables with vehicular equipment of
sufficient weight to cause cable damage. Welcoming crowds at a ship’s homecoming may require
crowd control from security forces to maintain safe approach distances (see Table 12).
Identification of cable voltage and other appropriate safety hazard information should be provided
on all cables in conformance with activity requirements.
b. If there is any possibility that pier vault access is required emergency rescue equipment
will be readily available (see Picture M).
141
MIL-HDBK-1025/10
142
MIL-HDBK-1025/10
9.5.2.4 Normal Procedures. List purpose of the SOP, potential energy sources, tools
and personal protective equipment, references to other SOP’s, this handbook’s sections, and
OSHA sections and procedures, as applicable. The procedures may be broken down into
individual SOP’s such as the following activities.
i. Shore power location of accidental grounds on ship’s service electrical power called in
by ships.
j. Remote operation of shore circuit breakers from the pier electrical outlet assembly.
9.6 Portable Shore Power Cables and Receptacles. Portable shore power cables
and receptacles conform to specific specification requirements.
The insulation resistance of each cable should be tested before each use.
9.6.3.1 Shore Criteria for Cable Assemblies. Cables having insulation readings below
1 megohm for 480-volt service cables and 5 megohms for 4,160-volt service cables will not be
placed in service. Shop testing and repair will be initiated for cable not meeting these
requirements.
9.6.3.2 Ship Criteria for 480-Volt Power Cable. Ship’s service voltage is a 480-volt
system using 600-volt cable. Insulation resistance should not be less than 280 megohms per meter
(920 megohms per foot) in warm ambient temperature or 1,676 megohms per meter (5,500
megohms per foot) in cold ambient temperature. A warm ambient temperature is defined as a
climate or a condition in which the entire cable is in a heated space and not in contact with the
ship’s hull. A cold ambient temperature is defined as a cold climate or a condition in which most
of the cable is in an unheated space or in contact with the ship’s hull.
a. Portable shore power cable jumper supplied by the ship where piers do not have
MIL-C-24368, Type 2 receptacle and plug assemblies or
144
MIL-HDBK-1025/10
b. Cables serving submarines will have MIL-C-24368, Type 5 outboard plug connection
permanently attached to the shipboard end.
145
MIL-HDBK-1025/10
146
MIL-HDBK-1025/10
9.7.1 Laying, Inspecting, and Testing Power Cable Assemblies. Power cables
should be removed from shore storage and transported to the pier where the ship will dock.
Qualified personnel should proceed as follows for each cable assembly connection.
9.7.1.1 Laying Power Cable Assemblies. This procedure involves moving the power
cables from the storage place to where it is laid out on the pier.
a. The only vehicles authorized to drag power cables on the piers are a shop mule, a line
truck, a reel truck, or a boom truck. Operators should have a valid state commercial drivers
license (CDL), should have a current medical examination, and should be physically and mentally
fit to operate the vehicle. In addition, boom truck operators should have a valid category 4 crane
operator’s license.
c. Check pier area for obstructions that may prevent the shore power set up. If obstacles
are present contact your work leader or foreman to inform them of the problem.
d. Place vehicle in position. Whenever possible, use a second person when backing up or
placing in tight space.
(5) No unauthorized persons are in the area that may be struck from swinging or falling
cable.
(6) For boom trucks, outriggers are not blocked by any obstructions and are not set on
top of vault covers, steam covers, or manholes. The boom should not swing forward of the
outriggers.
9.7.1.2 Moving Power Cable Assemblies on Pier. Be sure each set of power cables is
dragged as a unit.
147
MIL-HDBK-1025/10
a. Cables should not be permitted to lay on sharp or ragged objects such as gunwales.
Sharp bends should be avoided. The cables should lay in wooden saddles or be wrapped in
canvas. Splices and connectors should be raised from the deck or pier for protection against
water contamination. Ensure cables are of sufficient length to allow enough slack for the rise and
fall of the tide, but not of sufficient length to permit them to dip into the water or become wedged
between the ship and pier.
b. Lay out the cables between the supplying shore power outlet and the ship’s cable port.
Lay out excess cable in a manner so as to minimize damage and abuse from vehicle and pedestrian
movement.
c. Never use feet to hold the cable in place as this may result in a foot or leg injury.
e. Ensure cables are of proper length and visually appear to be arranged neatly and safely.
f. Ensure ends of cables are not connected to any shore or vehicle device.
WARNING
a. Test shore power cable assemblies with voltage tester to ensure cables are de-energized
prior to handling.
b. Lay out and visually inspect shore power cable assemblies for any sign of defects such
a cracks, bulges, or indications of overheating. Inspect cable sheath for cuts, nicks, and gouges.
When required, strip insulation from any existing cable splice(s) and inspect for cleanliness,
tightness, and good surface contact. Repair all defects and reinsulate. When required, splice and
insulate 3 meters (10 feet) of cable length with a plug to each cable of a shore power cable
assembly.
c. Open shore power cable assembly covers. Clean covers and cable plugs. Inspect cover
gaskets for cuts, tears, cracks, and deformation. Inspect each plug conducting surface for pitting,
corrosion, and evidence of overheating. Inspect cable connectors for pitting, corrosion, and
evidence of overheating. Apply a light coat of approved grease to cable connectors.
148
MIL-HDBK-1025/10
e. Use the megohmeter to verify phase identification markings of the cable assembly to
ensure proper orientation.
f. Tag shore power cable assembly with “DANGER-HIGH VOLTAGE” signs. Barricade
the work area surrounding the ship’s shore power receptacles. Hang plugs on the pier electrical
outlet assembly to which they will be connected.
WARNING
Tag out shore power receptacle circuit breakers in accordance with below
listed tag out procedures or local activity prepared procedures.
Disconnect equipment such as meters or indicating lights that could be
damaged by a megohmeter test or cause a false reading.
a. Remove indicator light and phase meter fuses. Ensure multimeter is in proper
operating condition by testing the meter on a known energized source before testing shore
receptacle power terminals.
b. Open access cover to each shore power receptacle and use a multimeter to test
terminals in each shore power receptacle to ensure that they are de-energized. Clean each cover
and receptacle. Inspect each cover gasket and each receptacle gasket for cuts, tears, cracks, and
deformation. Inspect each receptacle conducting surface for pitting, corrosion, and evidence of
overheating. Operate each receptacle interlock switch manually; movement should be smooth
with no binding or sticking.
c. Use a suitable megohmeter and test the insulation resistance between each receptacle
terminal and between each terminal and ground. Minimum insulation resistance is one megohm
for 480-volt receptacles and 5 megohms for 4,160-volt receptacles. Reinstall indicator light and
phase meter fuses. Close shore power receptacle access covers. Remove “DANGER” from
shore power circuit breakers and receptacle circuit breakers and replace with “CAUTION” tags in
accordance with tag out procedures. Indicate on ‘CAUTION” tags that if shore receptacle power
interlock and/or power control power transformer fuses are removed or blown, shore receptacle
149
MIL-HDBK-1025/10
power cover safety interlock will be inoperative and warn that high voltage will be present if
interlock fails.
d. Test shore power receptacle cover interlock switches and indicator lights as follows:
(4) Open shore power receptacle access cover; receptacle circuit breaker should trip
and indicating light should extinguish.
(5) Use an approved potential difference tester (see 5.1.4.1) and ensure it is in proper
operating condition by checking the tester on a known energized source before testing shore
power receptacle terminals.
(6) Test shore power receptacle with the tester to ensure it has been de-energized.
(9) Remove “CAUTION” tags and attach “DANGER” tags to shore power circuit
breakers in accordance with tag out procedures.
WARNING
Connections are to be made from the ship’s electric bus toward the shore
power receptacle. When distance from ship’s electric bus to the shore
power receptacle requires splicing of two or more cables, splicing should
be completed prior to making any ship or shore power receptacle
connections.
150
MIL-HDBK-1025/10
c. Use the tester to test the terminals in shore power receptacles to ensure they are
de-energized.
d. Insert shore power cable plugs into the shore power receptacle.
9.8 Shore-to-Ship Power Cable Rigging After Ship Docks. Upon ship’s arrival
contact ship’s electrical officer, determine cable connection time, provide necessary personnel,
and receive ship connect/disconnect form.
d. Load cable assemblies from shore to ship for extension by ship’s personnel to ship’s
electrical bus connection.
e. The ship’s electrical officer should give permission to shore personnel that shore
personnel are to energize shore power at a stated time. At that time after checking that electrical
power is supplied to the ship’s electrical bus the ship’s electrical officer will transfer the ship’s
electrical load within 10 seconds of shore power input.
WARNING
After the ship has notified that transfer has been completed, the
“DANGER” tags will be removed and necessary forms filled out and
signed. During the times cables are energized they are prohibited from
being moved.
WARNING
151
MIL-HDBK-1025/10
a. The ship’s electrical officer should give permission to shut down shore power at a
stated time after the ship’s generators have been started, synchronized, and have assumed the
electrical load. Paralleling of ship’s generators and shore power should be limited to 10 seconds
or less.
b. The ship’s electrical officer should receive notification that all shore power receptacle
circuit breakers are open and that “DANGER” tags have been attached on shore power receptacle
circuit breakers in accordance with tag out procedures.
WARNING
Ensure shore power receptacle circuit breakers are open and tagged,
shore power energized indicting lights are extinguished, and shore power
cable assemblies disconnected at the source.
d. Lower cable assemblies from the ship onto the pier and reel for shipment to the cable
storage area.
e. Notify the ship that all connections have been removed and necessary forms signed and
filled out.
152
MIL-HDBK-1025/10
INDEX
PARAGRAPH PAGE
Aerial lifts ......................................................................................... 7.2 66
Bucket safety precautions ....................................................... 7.2.6 70
Direction for installations........................................................ 7.3.1 72
Grounding .............................................................................. 5.3.7 39
Insulated buckets .................................................................... 7.2.7 71
Leakage current monitoring .................................................... 5.1.4.4 28
Manufacturing requirements ................................................... 7.2.3 67
Maintenance ........................................................................... 7.2.8 71
Operation near energized electrical facilities............................ 7.2.1 67
Other requirements ................................................................. 7.2.5 69
Safety ................................................................................... 7.2.4 68
Types ................................................................................... 7.2.2 67
Climbing and working on poles....................................................... 7.6 80
Before climbing precautions.................................................... 7.6.1 80
Crossing pole structures.......................................................... 7.9 90
Balancing support on poles.......................................... 7.9.2 90
Climbing H-frame pole structures ................................ 7.9.3 90
Crossing open air switches on poles ............................ 7.9.1 90
Pole climbing and work precautions........................................ 7.8 86
Concrete/steel pole or tower climbing precautions....... 7.8.3 87
General pole climbing precautions ............................... 7.8.4 87
Materials precautions while working on poles.............. 7.8.6 89
More than one climber ................................................ 7.8.1 86
Precautions while working on pole structures .............. 7.8.5 88
Wood-pole climbing precautions ................................. 7.8.2 86
Pole climbing equipment ......................................................... 7.7 81
Climber defects ........................................................... 7.7.2.2 83
Climber requirements .................................................. 7.7.2.1 83
Climbers’ tools............................................................ 7.7.3.4 86
Climbing safety equipment........................................... 7.7.1 82
Concrete/steel pole climbing........................................ 7.7.3 85
Conditioning climbing equipment ................................ 7.7.2.5 84
Fall arresting system provisions ................................... 7.7.3.3 86
Leather treatment........................................................ 7.7.2.3 83
Prohibited climber wearing areas ................................. 7.7.2.6 85
Storing climbing equipment ......................................... 7.7.2.4 84
Wood-pole climbing equipment ................................... 7.7.2 82
Type of pole ........................................................................... 7.6.2 81
153
MIL-HDBK-1025/10
PARAGRAPH PAGE
De-energized line work prescheduling............................................. 5.2 28
Hazardous energy elimination ................................................. 5.2.2.1 29
Lock and tag color coding ...................................................... 5.2.2.3 31
Lockout/tagout/tryout instructions.......................................... 5.2.2.2 30
Lockout/tagout/tryout of hazardous energy sources ................ 4.7 18
Preparation responsibility........................................................ 5.2.1 29
Safety basics ........................................................................... 5.2.2 29
Electrical aspects affecting safety .................................................... 5.1 23
Combustible gas/oxygen detectors .......................................... 5.1.4.3 28
De-energized electrical line work ............................................ 5.1.2.1 25
Energized electrical line work ................................................. 5.1.2.2 25
Number of qualified workers per hazard exposure................... 5.1.2.3 26
Phasing testers........................................................................ 5.1.4.2 28
Potential differences................................................................ 5.1.4.1 28
Safe working distances ........................................................... 5.1.1 23
Safety hazard detection devices............................................... 5.1.4 27
Verifying system and equipment provisions............................. 5.1.3 27
Work methods in relation to worker’s safety........................... 5.1.2 25
Energized electrical line work.......................................................... 5.4 43
General job-in-progress procedures......................................... 5.4.4 47
Insulating guards .................................................................... 5.4.2.3 45
Insulating tools ....................................................................... 5.4.2.2 44
Permitted electrical line work methods.................................... 5.4.1 43
Prework procedures................................................................ 5.4.3 46
Rubber goods ......................................................................... 5.4.2.1 44
Voltage levels and approved work methods and equipment..... 5.4.2 43
Energy-storing protective device safety .......................................... 6.7 57
Capacitor discharge circuits .................................................... 6.7.3.1 58
Capacitors .............................................................................. 6.7.3 58
Choke coils............................................................................. 6.7.2 58
Coupling capacitors ................................................................ 6.7.3.2 58
Disconnecting surge arresters.................................................. 6.7.1.2 57
Surge arrester contact............................................................. 6.7.1.1 57
Surge arresters........................................................................ 6.7.1 57
Fusing safety ................................................................................... 6.6 56
Bypassing ............................................................................... 6.6.5 57
Closed-position fuse holder..................................................... 6.6.3 56
Fuse handling.......................................................................... 6.6.1 56
Open fuse holder..................................................................... 6.6.3 56
Operation of energized fuses................................................... 6.6.2 56
154
MIL-HDBK-1025/10
PARAGRAPH PAGE
Grounding provisions ...................................................................... 5.3 31
Approach distances................................................................. 5.3.3.1 33
Equipotential (single point) grounding .................................... 5.3.2 32
Grounding cable ..................................................................... 5.3.4.2 34
Grounding clamps................................................................... 5.3.4.1 34
Grounding cluster bars............................................................ 5.3.4.4 35
Grounding ferrules.................................................................. 5.3.4.3 35
Grounding for stringing and removing lines............................. 5.3.10 41
Opening or splicing de-energized conductors .......................... 5.3.9 40
Placement of grounds ............................................................. 5.3.3 33
Potential differences................................................................ 5.3.3.2 33
Temporary grounding of aerial lines........................................ 5.3.5 36
Temporary grounding of substation
current-carrying equipment components .......................... 5.3.6 36
Temporary grounding of underground lines............................. 5.3.8 40
Temporary grounding system components .............................. 5.3.4 34
Why temporary grounds are necessary .................................... 5.3.1 32
Heating materials ............................................................................. 8.7 125
Eliminating heating material hazards ....................................... 8.7.1 125
Heating materials work precautions ........................................ 8.7.2 125
Instrument transformer safety......................................................... 6.8 59
Caution................................................................................... 6.8.2.1 60
Circuit opening ....................................................................... 6.8.2.1 60
Current transformers............................................................... 6.8.2 60
Fuse replacement .................................................................... 6.8.1.1 59
Supervisory requirements........................................................ 6.8.1.2 59
Voltage (potential) transformers ............................................. 6.8.1 59
Job hazards ...................................................................................... 4.2 7
Accessibility............................................................................ 4.2.1 7
Aerial work ............................................................................ 4.2.1.3 8
Asbestos................................................................................. 4.2.4.1 9
At grade work ........................................................................ 4.2.1.2 7
Explosive or hazardous vapors................................................ 4.2.5 9
Hazardous environmental impacts........................................... 4.2.4 8
Inside work............................................................................. 4.2.1.1 7
Lighting.................................................................................. 4.2.3.4 8
Noise control.......................................................................... 4.2.3.3 8
Normal environmental impacts................................................ 4.2.3 8
Polychlorinated biphenyls (PCB)............................................. 4.2.4.2 9
155
MIL-HDBK-1025/10
PARAGRAPH PAGE
Reminder of electrical hazards in the field ............................... 4.3 10
Danger from arcs and blasts ........................................ 4.3.2 11
Dangers from electric shock ........................................ 4.3.1 10
Sulfur hexafluoride (SF6) ........................................................ 4.2.4.3 9
Underground work ................................................................. 4.2.1.4 8
Unusual shore-to-ship system hazards..................................... 9.4 136
Electrical equipment accessibility and working space ... 9.4.3 137
Parallel operation ........................................................ 9.4.5 139
Portable power cable and outlet safety assurance......... 9.4.2 137
Readily accessible........................................................ 9.4.3.1 137
Ship's electrical power input safety .............................. 9.4.4 138
Split personnel responsibilities..................................... 9.4.1 137
Working space ............................................................ 9.4.3.2 138
Wood product preservative treatments.................................... 4.2.4.4 9
Work area protection.............................................................. 4.2.2 8
Work in confined or enclosed spaces....................................... 4.2.3.2 8
Work in elevated positions or near waterways......................... 4.2.3.1 8
Metal clad switchgear safety............................................................ 6.10 61
Before circuit breaker drawout requirements........................... 6.10.1 61
Circuit breaker maintenance.................................................... 6.10.2 62
Safety precautions after circuit breaker maintenance ............... 6.10.3 62
Network protector safety ................................................................. 6.11 62
After network protector maintenance...................................... 6.11.3 64
Closing network protectors..................................................... 6.11.1 63
Network protector maintenance safety .................................... 6.11.2 63
Pole linework environment .............................................................. 7.1 66
Dismantling Poles ................................................................... 7.5 79
Additional pole support............................................... 7.5.2 79
Minimum pole support ................................................ 7.5.1 79
Pole removal ............................................................... 7.5.4 80
Truck restraining......................................................... 7.5.3 79
Pole handling operations ......................................................... 7.3 72
Direction of aerial lift for installation ........................... 7.3.1 72
Facility receipt............................................................. 7.3.3 72
Ground handling ......................................................... 7.3.4 73
Hauling poles .............................................................. 7.3.6 74
Pole contact precautions.............................................. 7.3.2 72
Temporary pole storage .............................................. 7.3.5 74
Pole installation requirements.................................................. 7.4 75
Backfilling around poles .............................................. 7.4.4.6 79
156
MIL-HDBK-1025/10
PARAGRAPH PAGE
Digging holes .............................................................. 7.4.2 75
Energized line precautions........................................... 7.4.4.5 78
Gin pole method.......................................................... 7.4.4.3 78
Hole covers................................................................. 7.4.3 75
Pike pole method ........................................................ 7.4.4.1 76
Pole holes ................................................................... 7.4.1 75
Pole setting truck precautions...................................... 7.4.4.4 78
Setting poles ............................................................... 7.4.4 76
Winch line method ...................................................... 7.4.4.2 77
Working on or around pole-mounted equipment ..................... 7.12 97
Aerial capacitors ......................................................... 7.12.3 97
Aerial connection ........................................................ 7.12.4.3 98
Aerial energized work ................................................. 7.12.4.1 98
Aerial fusing................................................................ 7.12.4.5 99
Aerial inspection and maintenance ............................... 7.12.4.4 99
Aerial installation ........................................................ 7.12.4.2 98
Aerial power transformers and voltage regulators........ 7.12.4 97
Aerial service connections ........................................... 7.12.4.6 99
Aerial surge arresters................................................... 7.12.1 97
Aerial switches and fuses............................................. 7.12.2 97
Aerial testing............................................................... 7.12.4.7 100
Portable shore power cables and receptacles .................................. 9.6 143
Explanation of criteria differences ........................................... 9.6.3.3 144
Low-voltage (480-volt) power cable specification................... 9.6.1 143
Low-voltage (480-volt) receptacle protective circuit breakers . 9.6.4.3 145
Low-voltage receptacles, plugs, and protective circuit breakers 9.6.4 144
Medium-voltage (4,160-volt) power cable specification .......... 9.6.2 144
Medium-voltage receptacles, plugs, and
protective circuit breakers .............................................. 9.6.5 145
Medium-voltage, (4,160-volt) receptacle protective circuit
breakers ......................................................................... 9.6.5.3 146
Pier low-voltage (480-volt) electrical outlet assemblies ........... 9.6.4.2 145
Pier medium-voltage (4,160-volt) electrical outlet assemblies.. 9.6.5.2 146
Power cable-in-use insulation resistance values ....................... 9.6.3 144
Ship criteria for 450-volt service cable .................................... 9.6.3.2 144
Shipboard connection ............................................................. 9.6.4.1 144
Shipboard connections............................................................ 9.6.5.1 145
Shore criteria for cable assemblies........................................... 9.6.3.1 144
Protection against hazards............................................................... 4.4 11
General body protection.......................................................... 4.4.1 11
157
MIL-HDBK-1025/10
PARAGRAPH PAGE
Live-line tools......................................................................... 4.4.2.3 14
Other safety requirements ....................................................... 4.4.2.4 15
Plastic guard equipment .......................................................... 4.4.2.2 14
Rubber protective equipment .................................................. 4.4.2.1 14
Safety equipment and tools ..................................................... 4.4.2 14
Relation of ship’s electrical service components ............................. 9.3 134
Electrical circuit arrangement.................................................. 9.3.2 134
Equipment physical relationship .............................................. 9.3.1 134
General electrical system safety............................................... 9.3.2.1 134
Specific shore-to-ship electrical system safety ......................... 9.3.2.2 135
Safety ................................................................................................ 4.1 7
Application ............................................................................. 4.1.4 7
Checklist for safety ................................................................. 6.3 53
Communication channel availability ............................. 6.3.1 53
Equipment preparation ................................................ 6.3.5 53
Lighting level .............................................................. 6.3.2 53
Personnel requirements ............................................... 6.3.4 53
Working period........................................................... 6.3.3 53
Construction........................................................................... 4.1.2 7
General safety observances ..................................................... 4.5 15
Power transformer and regulator safety................................... 6.9 60
Power transformers ..................................................... 6.9.1 60
Voltage regulators....................................................... 6.9.2 61
Qualifying personnel ............................................................... 4.1.3 7
Switching safety...................................................................... 6.5 54
Air switches ................................................................ 6.5.1 54
Airbreak switches........................................................ 6.5.1.2 55
Disconnect switches .................................................... 6.5.1.1 54
Inching........................................................................ 6.5.1.4 55
Interrupter switches..................................................... 6.5.1.3 55
Unique requirements............................................................... 4.1.5 7
Use......................................................................................... 4.1.1 7
Requirements for safely phasing or connecting of circuits........ 6.13 65
Storage battery safety ............................................................. 6.12 64
Testing safety ......................................................................... 6.4 53
Worker/crew responsibilities................................................... 4.6 15
Knowing what to do.................................................... 4.6.3.1 16
Levels of responsibility................................................ 4.6.1 15
Mishap handling .......................................................... 4.6.3 16
Qualifications .............................................................. 4.6.2 15
158
MIL-HDBK-1025/10
PARAGRAPH PAGE
Qualified workers........................................................ 4.6.2.1 15
Rescue operations ....................................................... 4.6.3.3 18
Unqualified workers .................................................... 4.6.2.2 15
Work injuries and mishap reports ................................ 4.6.3.2 18
Streetlighting ................................................................................... 7.11 96
Climbing space ....................................................................... 7.11.4 97
Multiple streetlighting circuits................................................. 7.11.2 96
Series streetlighting circuits .................................................... 7.11.3 96
Streetlighting precautions ....................................................... 7.11.1 96
Time switches......................................................................... 7.11.5 97
Stringing or removing de-energized conductors ............................. 7.10 90
Adjacent to energized lines .................................................... 7.10.1.1 90
Clipping in or tieing primary line wires.................................... 7.10.5.2 93
Common neutral systems ........................................................ 7.10.3.2 92
Conductor grounding.............................................................. 7.10.4.3 92
Conductors............................................................................. 7.10.4.2 92
De-energized line grounding ................................................... 7.10.3 91
Fallen wires ............................................................................ 7.10.2.1 91
Fire ................................................................................... 7.10.2.2 91
Guy installation....................................................................... 7.10.8.1 95
Guying ................................................................................... 7.10.8 95
Handling and stringing guidance ............................................. 7.10.4 92
Insulators................................................................................ 7.10.9 96
Line work precautions ............................................................ 7.10.1 90
Other work precautions affecting aerial lines ........................... 7.10.2 91
Over, under, or across energized lines..................................... 7.10.1.2 91
Permanent ground wires ......................................................... 7.10.3.1 91
Primary line installation........................................................... 7.10.5 92
Protecting secondary lines....................................................... 7.10.6.2 94
Protective grounding equipment.............................................. 7.10.3.3 92
Reels ................................................................................... 7.10.4.1 92
Removal of guys..................................................................... 7.10.8.2 96
Removing lines ....................................................................... 7.10.7 94
Secondary line installation....................................................... 7.10.6 93
Stringing primary line wires .................................................... 7.10.5.1 93
Stringing secondary line wires................................................. 7.10.6.1 94
Vehicular protection ............................................................... 7.10.2.3 91
Substation work area control .......................................................... 6.2 50
Adjacent energized equipment protection................................ 6.2.3.6 52
159
MIL-HDBK-1025/10
PARAGRAPH PAGE
Barriers and barricade tape ..................................................... 6.2.3.3 51
Clearance access..................................................................... 6.2.2 51
De-energizing proof testing..................................................... 6.2.3.4 51
De-energizing work areas ....................................................... 6.2.3 51
Installation precautions ........................................................... 6.2.5 53
Lockout/tagout/tryout ............................................................ 6.2.3.2 51
Previsit briefing....................................................................... 6.2.1 50
Switching ............................................................................... 6.2.3.1 51
Work area grounding.............................................................. 6.2.3.5 52
Worker protection .................................................................. 6.2.3.7 52
Working area housekeeping checks......................................... 6.2.4 52
Supporting shore-to-ship safety requirements................................ 9.5 139
Connect/disconnect performance responsibilities ..................... 9.1 127
Emergency procedures............................................................ 9.5.2.5 143
Normal procedures ................................................................. 9.5.2.4 143
Priorities................................................................................. 9.5.2.3 140
SOP preparation responsibility ................................................ 9.5.2.1 139
Specialized shore-to-ship system training ................................ 9.5.1 139
Specific organization requirements.......................................... 9.5.2.2 140
Specific SOP's ........................................................................ 9.5.2 139
Ship connection procedures before ship docks ........................ 9.7 146
Checking shore receptacles.......................................... 9.7.2 149
Inserting cable plugs into receptacles........................... 9.7.2.1 150
Inspecting and testing power cable assemblies ............. 9.7.1.3 148
Laying power cable assemblies .................................... 9.7.1.1 147
Laying, inspecting, and testing power cable assemblies 9.7.1 146
Moving power cable assemblies on pier ....................... 9.7.1.2 147
Ship’s main electrical service components ............................... 9.2 127
Pier substations ........................................................... 9.2.2 128
Ship-to-shore pier electrical outlet assemblies.............. 9.2.3 128
Ship-to-shore power cables and connectors ................. 9.2.4 128
Shore medium-voltage distribution system................... 9.2.1 128
Ship’s transfer back to the ship’s generator ............................. 9.10 151
Ship’s transfer to shore power ................................................ 9.9 151
Shores disconnection of cable plugs and removal of cable
assemblies ................................................................... 9.11 152
Shore-to-ship power cable rigging after ship docks ................. 9.8 151
System familiarity ............................................................................ 6.1 49
Abnormal conditions............................................................... 6.1.4 50
Alarms ................................................................................... 6.1.3.2 49
160
MIL-HDBK-1025/10
PARAGRAPH PAGE
Defective equipment ............................................................... 6.1.5 50
Diagrams and schematics ........................................................ 6.1.1 49
Engineering guidance.............................................................. 6.1.2 49
Interlocking ............................................................................ 6.1.3.3 49
Protective devices................................................................... 6.1.3.1 49
System operation .................................................................... 6.1.3 49
Training.................................................................................. 4.8 19
Programs .................................................................... 4.8.1 20
Standard operating procedures/job hazard analysis ...... 4.8.2 22
Tree trimming and brush removal .................................................. 7.13 100
Chain saws ............................................................................. 7.13.6.2 103
Climbing and working on trees................................................ 7.13.5 101
Operating power trimming equipment ..................................... 7.13.6.1 102
Power trimming equipment ..................................................... 7.13.6 102
Right-of-way brush removal.................................................... 7.13.6.3 103
Tree climbers.......................................................................... 7.13.5.1 101
Tree trimming public safety..................................................... 7.13.2 100
Tree trimming tool safety........................................................ 7.13.3 100
Tree trimming training qualifications ....................................... 7.13.1 100
Tree work............................................................................... 7.13.5.2 101
Working on trees near energized lines ..................................... 7.13.4 101
Underground work........................................................................... 8.1 105
Excavation practices and procedures for damage control......... 8.4 111
Accountability for excavator error............................... 8.4.8 114
All projects preplanning............................................... 8.4.2 111
Backfilling in areas of utility locations ......................... 8.4.6 113
Excavating in areas of utility locations......................... 8.4.5 112
If damage does occur to existing utilities ..................... 8.4.7 113
Large project preplanning............................................ 8.4.3 111
On the job site procedures........................................... 8.4.4 111
Preplanning of the excavation project .......................... 8.4.1 111
Existing obstruction protection ............................................... 8.3 109
Digging restriction ...................................................... 8.3 109
Direct-burial electrical cable work ............................... 8.3.2 109
Handling damage to existing utility line ....................... 8.3.4 110
Locating buried facilities ............................................. 8.3.1 109
Preparation for work in underground structures ...................... 8.5 114
Elimination of combustible or toxic gases .................... 8.5.2.3 118
Emergency entrance into underground structures ........ 8.5.2.5 119
Forced air.................................................................... 8.5.3.1 119
161
MIL-HDBK-1025/10
PARAGRAPH PAGE
Hazardous conditions in underground structures ......... 8.5.2.1 117
Natural method ........................................................... 8.5.3.3 119
Removing a manhole cover ......................................... 8.5.1 114
Sail method ................................................................. 8.5.3.2 119
Structure condition change retesting requirements....... 8.5.2.4 118
Testers for underground structures.............................. 8.5.2.2 117
Testing before entering underground structures ........... 8.5.2 116
Ventilation of underground structures ......................... 8.5.3 119
Underground work area protection ......................................... 8.2 105
Barricades and warning precautions............................. 8.2.4 105
Barriers and barricade tape......................................... 8.2.4.3 106
Cable pulling protection .............................................. 8.2.4.7 109
Caution and danger signs............................................. 8.2.4.4 107
Devices ....................................................................... 8.2.4.1 106
Excavation, trenching, and backfilling.......................... 8.2.4.6 107
Flagmen ...................................................................... 8.2.4.2 106
Impact of vehicular traffic flow.................................... 8.2.2 105
Manhole work areas.................................................... 8.2.4.5 107
Underground work area protection methods................ 8.2.1 105
Work space considerations .......................................... 8.2.3 105
Work inside underground structures ....................................... 8.6 120
Cutting of underground cables..................................... 8.6.5 124
De-energizing underground cables and equipment ....... 8.6.3 122
General inside structure safety..................................... 8.6.1 120
Grounding switch operation ........................................ 8.6.4.4 123
Isolation of underground lines ..................................... 8.6.3.1 122
Precautions before de-energizing underground lines .... 8.6.2 121
Protection against energized parts ............................... 8.6.4.2 122
Requirements for working on underground cables
and apparatus.......................................................... 8.6.4 122
Underground cable and equipment grounding.............. 8.6.3.2 122
Underground de-energized work ................................. 8.6.4.1 122
Underground working procedures ............................... 8.6.4.3 123
PROJECT NO.
FACR-5001
162
STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL
INSTRUCTIONS
1. The preparing activity must complete blocks 1, 2, 3, and 8. In block 1, both the document number and
revision letter should be given.
2. The submitter of this form must complete blocks 4, 5, 6, and 7.
3. The preparing activity must provide a reply within 30 days from receipt of the form.
NOTE: This form may not be used to request copies of documents, nor to request waivers, or clarification
of requirements on current contracts. Comments submitted on this form do not constitute or imply
authorization to waive any portion of the referenced document(s) or to amend contractual requirements.
1. DOCUMENT NUMBER 2. DOCUMENT DATE (YYMMDD)
I RECOMMEND A CHANGE:
MIL-HDBK-1025/10 981201
3. DOCUMENT TITLE :
Safety of Electrical Transmission and Distribution Systems
4. NATURE OF CHANGE (identify paragraph number and include proposed rewrite, if possible. Attach extra sheets as needed.)
6. SUBMITTER
a. NAME (Last, First, Middle Initial) b. ORGANIZATION
c. ADDRESS (Include Zip Code) d. TELEPHONE (Include Area Code) 7. DATE SUBMITTED:
(1) Commercial (YYMMDD)
(2) DSN
(If applicable)
8. PREPARING ACTIVITY
a. NAME b. TELEPHONE (Include Area Code)
COMMANDER
(1) Commercial (2) DSN
NAVAL FACILITIES ENGINEERING COMMAND
ATTN CRITERIA OFFICE
(757) 322-4208 262-4208
c. ADDRESS (Include Zip Code)
IF YOU DO NOT RECEIVE A REPLY WITHIN
1510 GILBERT STREET 45 DAYS, CONTACT:
NORFOLK, VA 23511-2699 Defense Quality and Standardization Office
5203 Leesburg Pike, Suite 1403, Falls Church,
VA 22041-3466
Telephone (703) 756-2340 DSN 289-2340
DD Form 1426, OCT 89
Previous editions are obsolete. 198/290