HYPERPLAS STANDARD

MEMBRANE R

1
HYPERPLAS STANDARD
R
MEMBRANE
Uses completely to eliminate all sharp projections. After
Standard Membrane is used as a damp proofing cleaning, suitable primer such IWL Primer / IWL CS /
membrane in horizontal and vertical applications for IWL Blown Bitumen 85/25 or 90/15 is coated on the
protection of various substrates like concrete, masonry, surface (for more details refer relevant data sheets).
basement, roof slab in wide ranges of uses. Hyperplas Standard is unrolled over the coated surface
(with overlaps of 10cm) and bonded completely to the
Medium to large roof slab (domestic, commercial
substrate. The overlaps are then sealed by flame.
and industrial)
Special care is taken at singularities such as drains,
Basement and raft slabs.
expansion joints, etc. Details of application are
Roof Gardens where resistance is not required.
available in Hyperplas Application Guide.
Advantages Hyperplas Standard can be topped with topping such
as cement screed or tiles on accessible roofs with a
High tensile strength, tear and puncture resistance. chicken wire mesh reinforcement. Inaccessible roofs
Capable of withstanding thermal movements. can be topped with a layer of Bitumen followed with a
No flame hazard and environment friendly layer of IWL Aluminium Paint.
Fast application
Good adhesion to primed concrete substrates
Limitation
Application temperature ranges from 15⁰C to 50⁰C. It
Description is better to warm the back of the membrane for
Hyperplas Standard is a high softening point, APP application below 15⁰C and should be stored at above
modified polymeric waterproofing membrane 20⁰C before application to enable easy application and
manufactures to the highest technical standards. It immediate bond to the substrate.
consists of a center core of High Molecular High
Density Polyethylene film. This polyethylene film is the Packing
heart of the membrane and is a complete barrier Hyperplas Polyester Membrane: 10m length X 1m width
against water and moisture. The center core is Coldstick: 20 Kg container
protected on both sides with a high quality Polymeric
Asphaltic mix with properties of high penetration, high Coverage
heat resistance and high softening point to make it Coldstick: 3-4 per sq.m/kg on a standard smooth surface
ideal for waterproofing purposes. It also achieves high
bonding strength with substrate and a strong adhesion Storage
between overlaps. The Polymeric Asphaltic mix is All product have a shelf life of 12 months if stored in a
protected on both sides with thermofusible HMHDPE cool, dry place away from sources of heat, in the
film. This aids the thermofusion process and also original unopened packing. It should be stored
reinforces the non permeable quality of the entire horizontally, not more than one pallet high.
membrane. The resultant membrane has elongation
exceeding 300% to absorb all structural movements. It
also has high tensile strength and is extremely flexible
Safety measures
No health hazards with the use of Hyperplas
and pliable to adapt to contours.
Membrane and Coldstick. If Coldstick Primer is
swallowed, drink a glass of water and do not induce
Surface preparation vomiting. When contacted with eyes occurs flood with
Smooth surface is required to apply the membrane. copius amounts of clean water for at least 15 minutes
The surface is first cleaned to eliminate all sharp and seek medical advice. If contacted with skin wash
projection. the skin thoroughly.

Priming Fire
IWL Primer / IWL CS / IWL Blown Bitumen is then Hyperplas Membrane and Coldstick are flammable.
coated on the surface (for more details refer relevant Do not smoke near these products. Coldstick contains
data sheets). volatile flammable solvents. Use only in open areas,
well away from sources of ignition.
Application
Application of Hyperplas Standard is fast and easy. Specification
Smooth surface with minimum slope is required to Hyperplas Standard is available in grades of 2mm,
apply the membrane. The surface is first cleaned 3mm, 4mm, 2Kg, 3Kg, 3.5Kg or 4Kg.

2
HYPERPLAS STANDARD
R
MEMBRANE

Technical Support

Requirement
Requirement
Requirement for Mineral
for Method of
S. No. Test for Plain Membrane Unit
Aluminium Test, Ref to
Membrane (including
Membrane
Aluminium)

Weight thickness of
1 membrane(both plain 2 ± 5% 3 ± 5% 4 ± 5% Kg Measurement
and aluminum)

Does not Does not Does not

Cold flexibility (both IS 13826
2 crack crack crack ⁰C
plain and aluminum) (Part 2)
at 5⁰C at 5⁰C at 5⁰C

Softening point, Min

3 (both plain and 120 120 120 o
C IS 1205
aluminum)

Tensile strength:
a)Plain: 70 ± 20% 120 ± 20% 130 ± 20% N/5cm
1)Longitudinal 60 ± 20% 100 ± 20% 100 ± 20% @23⁰C
IS 13826
4 2)Transverse (part 1)
b)3mm and above 100 ± 20% 120 ± 20% 150 ± 20% N/5cm
1)Longitudinal 80 ± 20% 100 ± 20% 100 ± 20% @23⁰C
2) Transverse

Elongation
a)Plain: 100 ± 20% 200 ± 20% 200 ± 20%
1) Longitudinal %
100 ± 20% 100 ± 20% 100 ± 20%
IS13826
5 2) Transverse
(Part 1)
b) Aluminum: 50 ± 20% 100 ± 20% 100 ± 20%
1) Longitudinal 50 ± 20% 100 ± 20% 100 ± 20%
2) Transverse

Tear Strength 150 Min

100 Min 120 Min
a) Longitudinal B-4 of IS
6 N
b) Transverse (both plain 7193
80 Min 100 Min 100 Min
and aluminum)

Heat resistance IS 13826

7 (both plain and aluminum) No Flow No Flow No Flow 100⁰C, 2h (part 5)

Penetration @ 25⁰C
100g,5s (both plain and Dmm (tenths
8 15 ± 5 15 ± 5 15 ± 5 IS 1203
aluminum) of mm)

Water absorption (both IS 13826

9 plain and aluminum) 0.2 Max 0.2 Max 0.2 Max %
(part 6)

Pressure head test No sign of No sign of No sign of IS 13826

10 %
leakage leakage leakage (part 4)

Puncture resistance test Shall show no Shall show no Shall show no

11 sign of sign of sign of - Annex C
(Optional)
puncture puncture puncture

3
 R

HYPERPLAS STANDARD MEMBRANE

IWL INDIA LIMITED

DELHI

MUMBAI

VISAKHAPATNAM

CHENNAI

- Sales & Marketing

- Factory

IWL India Limited was incorporated in 1988, to manufacture revolutionary,

modified bitumen based, waterproofing membranes and anti corrosive IWL INDIA LIMITED - HEAD OFFICE
tapes. Since then, we have diversified into a number of other product lines,
including Road Products, Liquid Waterproofing Membranes, Coatings, W-360, North Main Road, Anna Nagar
Adhesives, Admixtures and Construction Chemicals. We have a dedicated West Extension, Chennai - 600 101
Ph: 044-26156000 / 044-26152100 /
team of 150 highly experienced professionals in our direct employ. With an 044-26156900
ISO 9001 certification to boot, our products are approved by all major E-mail : [email protected]
consultants, clients and contractors including Military Engineering Services,
Nuclear Power Corporation of India, Engineers India Limited, National www.iwl.in
Thermal Power Corporation, Larsen & Toubro, Nuclear Power Complexat
Kudangulam, Nuclear Power Complex at Kaiga and Bangalore, Kolkatta, ISO 9001 : 2015 Certified Company
Delhi and Ahmedabad Metro Projects.

01-2018-A