Nitobond EP: Epoxy Resin Concrete Bonding Agent
Nitobond EP: Epoxy Resin Concrete Bonding Agent
Nitobond EP: Epoxy Resin Concrete Bonding Agent
Nitobond EP can be applied by brush. Adhesive strength to concrete : In general the bond strength
More overlay time:Enables to place the concrete upto 6 will always exceed the tensile strength of M30 concrete.
hrs after applying Nitobond EP, without risk of
Specification clauses
delamination
High bond strength : Bond strength is more than the The bonding agent shall be Nitobond EP an epoxy based two
tensile strength of good quality concrete component resin system prepacked in distinct colours to give
Barrier coat : Acts as a 'barrier coat' to the migration of visual evidence for proper mixing. The bonding agent should
chloride ions from host concrete. remain in tacky state after application for a minimum period
of 6 hours at 300C. There shall not be bond failure of the
Description
specimen when tested by slant shear method according to
BS 6319 pt 4, with M30 concrete.
Nitobond EP is based on solvent free epoxy resins containing
pigments and fine fillers. It is supplied as a two part material Application instructions
in preweighed quantities for ready onsite mixing and use.
Coloured components - white base and green hardener - Preparation
provide visual evidence that adequate mixing is achieved.
All surfaces to be treated must be firm, dust free and clean.
Technical support All laintence should be removed by etching with Reebaklens
and wire-brushing. In some cases, the existing concrete
The company provides a technical advisory service supported must be chipped to a sound substrate. Where surfaces are
by a team of specialists in the field. contaminated with oil or grease, this should be removed by
using a strong industrial detergent or organic degreaser.
Design criteria
Surface should be washed thoroughly with water and dried
before the application of Nitobond EP.
Nitobond EP is designed with an overlay time of 10 hrs at
200C, 6 hours at 30 0C making it more suitable for use where Mixing
additional steel reinforcement and formwork has to be fitted
The entire contents of the hardener can should be poured
or where temperature is high. The minimum application
into the resin container and the two materials thoroughly mixed
temperature for Nitobond EP is 10 0C. Consult the local Fosroc
until a uniform colour is obtained. To facilitate application at
office for further information.
temperatures below 10 0C the separate components should
Properties be warmed in hot water to a maximum of 25 0C before mixing.
At 200C At 30 0C Coating
Mixed Nitobond EP should be brush applied to the prepared
Pot life 5 - 6 hrs 2 - 3 hrs
surface. The new concrete should be placed within 6 hours
Nitobond® EP
Full cure 7 days 5 days at 300C to the Nitobond EP coated substrate, when it is in a
tacky state.
Overlay time 10 hrs 6 hrs
Nitobond® EP
Limitations Precautions
Nitobond EP should not be applied when the temperature is Health and Safety
below 100C. If any doubts arise concerning temperature or
Contact with skin and eyes should be avoided. Gloves should
substrate conditions, consult the local Fosroc office.
be used when handling these products. If contact wiith the
Estimating resin occurs, wash immediately with a strong detergent or a
resin removing cream. Eye contamination must be
Packaging immediately washed with plenty of water and medical
treatment sought.
Available in 1/2, 1 and 4 litre industrial packs.
Coverage Fire
Nitobond EP is inflammable. No naked flame should be
Approximately 2.6 m2/litre. Actual coverage will depend upon
allowed near the site. Do not smoke during use.
the texture and porosity of the substrate being covered.
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bellary: 09845891690 Bhubaneshwar : (0674) 2521176
Chennai : (044) 24899949/24853383 Chandigarh : (0172) 2639360 Cochin : (0484) 2347465 Coimbatore : (0422) 2472966
Goa : (0832) 09423058696 Guwahati : (0361) 2462866 Hyderabad : (040) 27662324/27662425 Indore : (0731) 4049339
Jaipur : (0141) 2336103 Lucknow :(0522) 2239044 Nagpur: (0712) 2753510/2563242 Visakhapatnam : (0891) 2564850 / 2707607
INDIA/0901/E