Professional Documents
Culture Documents
Axis 210/211 User's Manual
Axis 210/211 User's Manual
Network Cameras
User’s Manual
About this Document requirements for radiated emission according to limit B of
EN55022/1998, and the requirements for immunity according to
This manual is intended for administrators and users of the EN55024/1998 residential, commercial, and light industry.
AXIS 210/211 Network Camera and applies to firmware
release 4.40. It includes instructions for using and managing Japan - This is a class B product based on the standard of the
the AXIS 210/211 on your network. Previous experience of Voluntary Control Council for Interference from Information
networking will be of use when using this product. Some Technology Equipment (VCCI:2003 Class B ITE). If this is used
knowledge of UNIX or Linux-based systems may also be near a radio or television receiver in a domestic environment, it
beneficial, for developing shell scripts and applications. Later may cause radio interference. Install and use the equipment
versions of this document will be posted to the Axis Website, according to the instruction manual.
as required. See also the product’s online help, available via
the Web-based interface. Australia - This electronic device meets the requirements of the
Radio communications (Electromagnetic Compatibility) Standard
Safety Notices Used In This Manual 1998 AS/NZS 3548.
Caution! - Indicates a potential hazard that can damage the Canada - This Class B digital apparatus complies with Canadian
product. ICES-003 B by complience with EN55022: Class B.
Important! - Indicates a hazard that can seriously impair
operation. Liability
Do not proceed beyond any of the above notices until you Every care has been taken in the preparation of this manual.
have fully understood the implications. Please inform your local Axis office of any inaccuracies or
Intellectual Property Rights omissions. Axis Communications AB cannot be held responsible
for any technical or typographical errors and reserves the right to
Axis AB has intellectual property rights relating to make changes to the product and manuals without prior notice.
technology embodied in the product described in this Axis Communications AB makes no warranty of any kind with
document. In particular, and without limitation, these regard to the material contained within this document, including,
intellectual property rights may include one or more of the but not limited to, the implied warranties of merchantability and
patents listed at http://www.axis.com/patent.htm and one or fitness for a particular purpose. Axis Communications AB shall
more additional patents or pending patent applications in the not be liable nor responsible for incidental or consequential
US and other countries. damages in connection with the furnishing, performance or use of
this material.
This product contains licensed third-party software. See the
menu item “About” in the product’s user interface for more Trademark Acknowledgments
information. Boa, Ethernet, Internet Explorer, Linux, Microsoft, Mozilla,
Netscape Navigator, OS/2, UNIX, Windows, WWW are registered
This product contains source code copyright Apple Computer, trademarks of the respective holders. Java and all Java-based
Inc., under the terms of Apple Public Source License 2.0 (see trademarks and logos are trademarks or registered trademarks of
http://www.opensource.apple.com/apsl/). Sun Microsystems, Inc. in the United States and other countries.
The source code is available from: Axis Communications AB is independent of Sun Microsystems
http://developer.apple.com/darwin/projects/bonjour/ Inc. UPnPTM is a certification mark of the UPnPTM Implementers
Legal Considerations Corporation.
Video and audio surveillance can be prohibited by laws that Support
vary from country to country. Check the laws in your local Should you require any technical assistance, please contact your
region before using this product for surveillance purposes. Axis reseller. If your questions cannot be answered immediately,
This product includes one (1) MPEG-4 decoder license. To your reseller will forward your queries through the appropriate
purchase further licenses, contact your reseller. channels to ensure a rapid response. If you are connected to the
Electromagnetic Compatibility (EMC) Internet, you can:
• download user documentation and firmware updates
This equipment generates, uses and can radiate radio • find answers to resolved problems in the FAQ database. Search
frequency energy and, if not installed and used in accordance by product, category, or phrases
with the instructions, may cause harmful interference to radio • report problems to Axis support by logging in to your private
communications. However, there is no guarantee that support area
interference will not occur in a particular installation. • visit Axis Support at www.axis.com/techsup/
If this equipment does cause harmful interference to radio or Safety Notice - Battery Replacement
television reception, which can be determined by turning the The AXIS 210/211 uses a 3.0V CR2032 Lithium battery as the
equipment off and on, the user is encouraged to try to correct power supply for its internal real-time clock (RTC). Under normal
the interference by one or more of the following measures: conditions this battery will last for a minimum of 5 years. Low
Re-orient or relocate the receiving antenna. Increase the battery power affects the operation of the RTC, causing it to reset
separation between the equipment and receiver. Connect the at every power-up. A log message will appear when the battery
equipment to an outlet on a different circuit to the receiver. needs replacing. The battery should not be replaced unless
Consult your dealer or an experienced radio/TV technician required!
for help. Shielded (STP) network cables must be used with
this unit to ensure compliance with EMC standards. If the battery does need replacing, please observe the following:
• Danger of Explosion if battery is incorrectly replaced
USA - This equipment has been tested and found to comply • Replace only with the same or equivalent battery, as
with the limits for a Class B computing device pursuant to recommended by the manufacturer.
Subpart B of Part 15 of FCC rules, which are designed to • Dispose of used batteries according to the manufacturer's
provide reasonable protection against such interference when instructions.
operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference, AXIS 210/211 User’s Manual
in which case the user at his/her own expense will be Revision 4.0, Part No: 28519, 16-02-07
required to take whatever measures may be required to Copyright© Axis Communications AB, 2007
correct the interference.
Europe - This digital equipment fulfills the
AXIS COMMUNICATIONS
<Product Name> Quick User’s Guide
AXIS 210/211 3
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Product features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Extra features for the AXIS 211 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Accessing the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Access From a Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Accessing the camera from the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Focusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
The Live View Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Video Streams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Video Stream Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MPEG-4 protocols and communication methods . . . . . . . . . . . . . . . . . . . . . . . . . . 15
How to stream MPEG-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
The AXIS Media Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Other methods of accessing the video stream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Setup Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Accessing the Setup tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Video & Image settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Image Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Overlay/Mask Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Live View Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
HTML Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
External Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Sequence Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Event Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Event Servers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Configuring Event Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Port Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Date & Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Network - Basic TCP/IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4 AXIS 210/211
Introduction
This manual covers the following Axis Network Camera models:
• AXIS 210
• AXIS 211
All instructions and information in this manual are valid for both models unless otherwise
stated.
Product features
The AXIS 210/211 cameras are part of the latest generation of fully featured Axis Network
Cameras, and are all based on the AXIS ARTPEC-2 compression chip.
The most basic model is the AXIS 210. The AXIS 211 supports further features listed in the
overview below. Both models support the following features:
• Video streams from the camera available on the network as real-time, full frame
rate Motion JPEG and/or MPEG-4 video streams.
• Video Motion Detection - this can be used to trigger e.g. image uploads when
there is activity in the video image.
• Scheduled image uploads.
• IP address filtering and multilevel password protection.
• Alarm input and output, which can be connected to various external devices, e.g.
door sensors and alarm bells.
• Multiple video resolutions.
• Simultaneous access by up to 20 viewers when using Motion JPEG. If MPEG-4
multicast is used, the number of viewers is unlimited, but each viewer still needs a
separate MPEG-4 license. One license is included in the product, additional
licenses can be purchased separately.
• Privacy masking allows the concealment of parts of the image that should not be
viewable. Up to 3 areas can be configured as masked areas.
• Built-in web server that provides full access to all features via a standard web
browser.
6 AXIS 210/211 - Introduction
• Built-in scripting tool that allows the creation of basic applications. For advanced
functionality, the cameras can be accessed via the AXIS HTTP API (more info at
www.axis.com/developer).
Overview
AXIS 210 AXIS 211
Tele/wide puller
Status
indicator
Status
indicator
DC-Iris
control cable
Underside
Mounting
screw hole
Serial number
Control button
Power indicator
Network indicator
Rear panel
Network Connector - The camera connects to the network via a standard network
connector. The camera detects the speed of the local network segment
(10BaseT/100BaseTX Ethernet). This socket can also be used to power the AXIS 211 via
PoE (Power over Ethernet).
Serial Number - This number is used during installation.
Control Button - Press this button to install using the AXIS Internet Dynamic DNS Service
(see page 36) or to restore the factory default settings, as described in Resetting to the
Factory Default Settings, on page 42.
LED Indicators
After completion of the startup and self test routines, the multi-colored Network, Status,
and Power LED indicators show as follows:
LED Color Indication
Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity.
Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.
Unlit No network connection.
Status Green Steady green for normal operation.
Note: The Status LED can be configured to be unlit during normal operation, or to flash
only when the camera is accessed. To configure, go to Setup > System Options > LED
settings. See the online help files for more information.
Amber Steady during startup, during reset to factory default or when restoring settings.
Red Slow flash for failed upgrade.
Power Green Normal operation.
Amber Flashes green/amber during firmware upgrade.
AXIS 210/211 - Accessing the Camera 9
Note: The layout of the live view page in the AXIS 211 may have been customized to meet specific requirements.
Consequently, some of the examples and functions featured here may differ from those displayed on your
own Live View page.
10 AXIS 210/211 - Accessing the Camera
Focusing
To focus the AXIS 210, unscrew the AXIS 210
focus puller on the lens. Adjust the focus
as required. Re-tighten the focus puller.
Focus puller
The Video Format drop-down list allows the video format on the Live View
page to be temporarily changed.
The Output buttons control the Pulse - click this button to activate the
output directly from the Live output for a defined period of time, e.g.
View page. These buttons are to switch on a light for 20 seconds.
configured under Setup > Live
View Config > Layout. Active/Inactive - click these buttons to
manually start and stop a connected
device, e.g. switch a light on/off.
These buttons start and stop the Sequence Mode. This mode is created in
Setup > Live View Config > Sequence mode, and automatically displays the
view from 2 or more video sources at set intervals.
From the Source list, select the desired external video source. Note
that Sequence Mode must be stopped before selecting a source from
this list.
The Action buttons can trigger an event directly from the Live View page.
These are configured under Setup > Live View Config > Layout.
The Snapshot button saves a snapshot of the video image currently being
displayed. Right-click on the video image to save it in JPEG format on your
computer. This button is primarily intended for use when the AMC viewer
toolbar is not available.
AXIS 210/211 - Accessing the Camera 13
The Play/Stop button starts and stops the live video stream.
The Snapshot button saves a snapshot of the video image currently being
displayed. The Snapshot function and the target directory for saving snapshots
can be configured from the AMC Control Applet in the Windows Control Panel
(Internet Explorer for Windows only).
Click the View Full Screen button to make the video image fill the entire screen
area. No other windows will be visible. Press Esc (Escape) on the computer
keyboard to exit full screen.
The record button is used to record the current video stream. The location where
the image file is saved can be specified using the AMC control panel. To enable
recording, Select Live View Config > Viewer Settings > Enable recording
button.
14 AXIS 210/211 - Video Streams
Video Streams
The AXIS 210/211 provides several different image and video formats. The type to use
depends on your requirements and on the properties of your network.
The Live View page in the AXIS 210/211 provides access to Motion JPEG and MPEG-4
video streams, as well as to single JPEG images. Other applications and clients can also
access these video streams/images directly, without going via the Live View page.
Notes: •MPEG-4 is licensed technology. The AXIS 210/211 includes one viewing client license. Installing
additional unlicensed copies of the viewing client is prohibited. To purchase additional licenses,
contact your Axis reseller.
•All clients viewing the MPEG-4 stream must use the same set of coding tools.
AXIS 210/211 - Video Streams 15
Setup Tools
This section describes how to configure the cameras, and is intended for product
Administrators, who have unrestricted access to all the Setup tools, and Operators, who
have access to the settings for Video & Image, Live View Config and Event Configuration.
The camera is configured under Setup from a standard browser (see Technical
Specifications, on page 45).
Image Settings
Image Appearance
Adjust these settings to optimize the video images according to your requirements.
All configuration of images and overlays will affect the camera’s overall performance,
depending on how it is used and on the available bandwidth. Lower compression improves
video image quality, but increases the bandwidth.
The video image can be rotated and fine-tuned by adjusting the color level, the brightness,
and the contrast. Please see the online help for further information on these settings.
Changed video image settings have immediate effect on the MPEG-4 stream, but the
Motion JPEG stream will have to be started (or restarted) before the settings take effect.
20 AXIS 210/211 - Video & Image settings
Overlay/Mask Settings
Overlay/Mask Type Text, date and
When using an image time overlays
overlay, select from the Overlay image
following options the type to
use:
• Uploaded image as overlay
- usually used to provide
extra information in the
video image.
• Configurable areas as pri-
vacy masks - up to 3 areas
are used to conceal parts
of the video image.
The difference between an overlay and a privacy mask is that a privacy mask cannot be
bypassed by accessing the video stream with the help of the AXIS HTTP API, whereas an
overlay can.
Selecting the overlay/mask type will display further settings available for the selected type.
See the online help for further information.
AXIS 210/211 - Video & Image settings 21
There are a number of limitations when using overlay images, such as the size and
positioning of images. Please refer to the online help for more information.
Advanced Settings
These pages provide various settings for fine-tuning the video image. Note that the
advanced settings available depend on the camera model.
Camera Settings
To compensate for the lighting conditions, the white balance and exposure control can be
adjusted. If available, DC-Iris should always be enabled except during focusing, or when
using a non-DC-Iris lens.
The settings for Low-light behavior determine how the cameras will behave at low light
levels. These settings all affect video image quality and are basically a measure of how
much noise to allow in the video images.
Please see the online help for further instructions on these settings.
AXIS 210/211 - Video & Image settings 23
MPEG-4 Settings
Tools for adjusting the MPEG-4 settings and for controlling the video bit rate.
The MPEG-4 standard provides many different coding tools for various applications in
different situations. As most MPEG-4 clients do not support all of these tools, it is usual to
instead define and use subsets for different clients or groups of clients. These settings allow
you to define the type of viewing client to use.
Adjusting the maximum bit rate and setting it to a variable or constant is a good way of
controlling the bandwidth used by the MPEG-4 video stream. For more information on
these advanced settings, please see Video Streams, on page 14, and the online help.
AXIS Media Control
The AXIS Media Control (AMC) is installed automatically the first time the camera is
accessed from a browser. The AMC control panel can be opened by right-clicking on the
video image in the Live View web page. The AMC control panel can be used to configure
various network, video settings such as:
• Network reconnection strategy, multicast network interface, and MPEG-4 connection order
• MPEG-2 and MPEG-4 video processing settings and default video decoder setting
• Video snapshot and recording settings
• Pan Tilt Zoom (PTZ) settings such as joy stick settings and PTZ mode settings
For more information, please see the AMC readme file included with AMC, or the Axis
Media Control (AMC) User Manual available at www.axis.com.
24 AXIS 210/211 - Live View Config
http://<IP address>/operator/basic.shtml
AXIS 210/211 - Live View Config 25
User-defined CGI links can be used to issue advanced commands via the Axis HTTP API.
For more information, see the Developer pages at www.axis.com/developer
Action Buttons
The manual trigger buttons can be used to manually trigger and stop an event from the
Live View page. See Event Configuration, on page 29.
Enabling the display of the Snapshot button allows users to save a snapshot from the
video stream by clicking the button. This button is mainly intended for use with browsers
other than Internet Explorer for Windows, or when otherwise not using AXIS Media
Control (AMC) to view the video stream. AMC (an ActiveX control) for Internet Explorer
provides its own snapshot button.
Output Buttons
These buttons can then be used to manually activate the output from the Live View page,
e.g. to switch a light on and off. There are 2 options for how the output is activated:
• The Pulse button activates the output for a defined period
• Active/Inactive displays 2 buttons, one for each action (on/off)
Default Video Format
Select the default format to use on the Live View page. Checking the box for Show video
format selection displays a drop-down list on the Live View page allowing you to
temporarily change the format.
Note: It is also possible to view Motion JPEG when MPEG-4 is chosen as default and vice versa.
Default Viewer
When using Microsoft Internet Explorer (IE) for Windows, select your preferred method of
viewing moving images. The options are:
• AMC(ActiveX)- This is the best choice for fast image updating in Internet
Explorer, but might not be possible on computers that have restriction on the
installation of additional software.
• QuickTime - For use with MPEG-4 only, select this to use the QuickTime plug-in
for Microsoft Internet Explorer.
• Java applet - This alternative uses a Java applet to update the images in the
browser.
• Still Image - Displays still images only. Hit the Refresh button in your browser to
view a new image.
AXIS 210/211 - Live View Config 27
When using any other browser than Internet Explorer for Windows, select the appropriate
method from the drop-down list for viewing images. The available options are similar to
Internet Explorer except for Server Push. With this method, the camera maintains and
controls an open HTTP connection to the browser and sends data as and when required for
as long as required.Please see the online help for more information.
Viewer settings
Checking the Show viewer toolbar displays the viewer toolbar under the video stream in
your browser.
By checking the Enable MPEG-4 decoder installation box, it is also possible for the
Administrator to enable or disable the installation of the MPEG-4 decoder. This is used to
prevent the installation of unlicensed copies. Further decoder licenses can be purchased
from your Axis dealer. See also AXIS Media Control, on page 23.
Check the record button to record the current video stream. The location where the image
file is saved can be specified using the AMC Control Panel.
HTML Examples
You can add live video from the cameras to your own web site. The camera can transmit a
Motion JPEG or unicast MPEG-4 stream to up to 20 simultaneous connections, although
an administrator can restrict this to fewer. If multicast MPEG-4 is used, the video stream
will be available to an unlimited number of viewers connected to the parts of the network
where multicast is enabled. Please note that a separate MPEG-4 license is required for each
viewer.
Enter the Video Format, Image Type, Image size and other settings to suit your Web page
and click Update. The camera then generates the required source code for your
configuration. Copy this code and paste it into your own Web page code.
External Video
The cameras can also display video images from other Axis network cameras and video
servers, directly on the Live View page. These are known as External Video sources. These
external video sources are available from the drop-down list on the Live View page.
Click the Add button to open the External Video Source Setup dialog, which is used to
make all the necessary settings. Enter the IP address or host name of the external video
source you wish to add. Depending on the external source, then select either MPEG-2,
MPEG-4 or Motion JPEG as the type of video stream to receive.
Example of a path to an external video source:
http://192.168.0.125/axis-cgi/mjpeg/video.cgi
28 AXIS 210/211 - Live View Config
Sequence Mode
The Live View page can be configured to rotate through the internal and selected external
video sources, in order, or randomly.
Select the desired video sources and enter the time in seconds to display each source (up to
59 minutes). Click Save.
The Sequence buttons will appear on the Live View page to enable the viewer to start and
stop the sequence mode.
Please see the online help for more information.
AXIS 210/211 - Event Configuration 29
Event Configuration
An event in the camera is when an Event Type is activated and causes certain actions to
be performed. The event type is the set of parameters (or conditions) that specifies how and
when which actions will be performed. A common event type is when the camera uploads
images when an alarm occurs. Many event types use an Event Server, to e.g. upload
images to.
This section describes how to set up event servers and event types, i.e. how to configure the
cameras to perform certain actions when events (e.g. alarms) occur.
Definitions
Event type A set of parameters describing how and when the camera will perform certain actions
The circumstances that start an event. E.g. on a signal from an external device, such as a
Triggered Event - see page 30
door switch or a motion sensor.
Scheduled Event - see page 31 The circumstances that start an event. E.g. at a pre-programmed time.
What occurs when the event triggers. E.g. the upload of images to an FTP server, e-mail
Action
notification, etc.
Event Servers
Event Servers are used to receive e.g. uploaded image files and/or notification messages. To
set up Event server connections in your cameras, go to Setup > Event Configuration >
Event Servers and enter the required information for the required server type.
Server type Purpose Information required
FTP Server • Receives uploaded images • Descriptive name of your choice
• Network address (IP address or host name)
• User Name and Password (for FTP server)
• Upload path e.g. images/
• Port number
• Use passive mode if there is a firewall between the camera
and FTP server
• Use temporary file if your FTP server doesn’t allow an existing
file to be overwritten by a new file with the same name
HTTP Server • Receives notification messages • Descriptive name of your choice
• Receives uploaded images • URL (IP address or host name)
• User Name and Password (for HTTP server)
• Proxy address/Proxy port (if required)
• Proxy User Name and Password (if required)
For details on each setting, please see the online help available from each web page.
When the setup is complete, the connection can be tested by clicking the Test button (the
connection test takes approximately 10 seconds).
30 AXIS 210/211 - Event Configuration
Configuring Event
Types
An Event Type describes
how and when the camera
will perform certain actions.
Triggered Event
A Triggered event can be activated by e.g:
• a push button connected to the camera’s input port
• detected movement in a configured motion detection window
• a manually activated action, e.g. from an action button in the web interface
• on restart (reboot) after e.g. power loss
How to set up a triggered event
This example describes how to set up the camera to upload images when e.g the main door
is opened:
1. Click Add triggered on the Event types page.
2. Enter a descriptive name for the event, e.g. Main door open.
3. Set the priority - High, Normal or Low (see the online help).
4. Set min time interval between triggers - This is the minimum time period that
the event type must wait after a trigger before it will be possible to trigger it
again. The interval commences as soon as the first trigger occurs. The shortest
possible interval is 1 second and the longest is 23 hours, 59 minutes and 59
seconds. To not use a minimum interval, set this option to 00:00:00
5. Set the Respond to Trigger... parameters for when the event will be active,
e.g. only after office hours.
6. Select the trigger alternative from the Triggered by... drop-down list, e.g. select
Input ports, for a sensor connected to the door.
7. Set the When Triggered... parameters, i.e. define what the camera will do if the
main door is opened e.g., upload images to an FTP server or send an e-mail
notification.
8. Click OK to save the Event in the Event Types list.
AXIS 210/211 - Event Configuration 31
Please see the online help for descriptions of each available option.
Note: Up to 10 event types can be configured in the cameras, and up to 3 of these can be configured to upload images. Files
names can be formatted according to specific requirements. See File Naming & Date/Time Formats online help.
Continue image upload (unbuffered) - enables the upload of video images for a fixed
length of time. Specify the length of time for the uploaded recording, in seconds, minutes
or hours, or for as long as the trigger is active. Finally, set the desired image frequency to
the maximum (the maximum available) or to a specified frame rate. The frame rate will be
the best possible, but might not be as high as specified, especially if uploading via a slow
connection.
Scheduled Event
A Scheduled event can be activated at preset times, in a repeating pattern on selected
weekdays.
Configuration example:
1. Click Add scheduled on the Event types page.
2. Enter a descriptive name for the event, e.g. “Scheduled e-mail upload.”
3. Set the priority (High, Normal or Low).
4. Set the Activation Time parameters (24h clock) when the event will be active,
e.g. start on Sundays at 13.00 with a duration of 12 hours.
5. Set the When Activated... parameters, i.e. set what the camera will do at the
specified time, e.g. send uploaded images to an e-mail address.
6. Click OK to save the Event in the Event Types list.
32 AXIS 210/211 - Event Configuration
Please see the online help for descriptions of each available option.
Motion Detection
Motion detection is used to generate an alarm whenever movement occurs (or stops) in the
video image. A total of 10 Include and/or Exclude windows can be configured.
• Included windows target specific areas within the whole video image
• Excluded windows define areas within an Include window that should be ignored
(areas outside Include windows are automatically ignored)
Once configured, the motion detection windows will appear in the list of available triggers,
for triggering events. See “How to set up a triggered event” on page 30.
Note: Using the motion detection feature may decrease the camera’s overall performance.
7. Click Save.
To exclude parts of the Include window, click the Configure Excluded Windows button
and position the Exclude window as required, within the Include window.
Please see the online help for descriptions of each available option.
Examples:
• Avoid triggering on small objects in the video image by setting the object size level to high.
• To reduce the number of triggers if there is a lot of movement during a short period of time, select a high
history level.
• To only detect flashing light, low sensitivity can be selected. In other cases, a high sensitivity level is
recommended.
Port Status
Under Event Configuration > Port Status there is a list showing the status for the
cameras’s input and output. This is for the benefit of Operators, who have no access to the
System Options section.
Example: If the Normal state for a push button connected to an input is set to Open circuit - as long as the but-
ton is not pushed, the state is inactive. If the button is pushed, the state of the input changes to active.
34 AXIS 210/211 - System Options
System Options
Security
User access control is enabled by default, when the administrator sets the root password on
first access. An administrator can set up other users, by giving these user names and
passwords. It is also possible to allow anonymous viewer login, which means that anybody
may access the Live View page, as described below:
Users - the user list displays the authorized users and user groups (levels):
Viewer Provides the lowest level of access, which only allows access to the Live View page.
Operator An operator can view the Live View page, create and modify event types and adjust certain other
settings. Operators have no access to the System Options.
Administrator An administrator has unrestricted access to all the setup tools and can determine the registration of
all other users.
IP Address Filtering
Enable IP Address Filtering- To allow or deny access to the AXIS 210/211 Network Camera
check the box Enable IP address filtering. Once enabled, the IP addresses in the list will be
allowed or denied access according to the choice made in the drop-down list Allow/Deny
the following IP addresses.
The administrator can add up to 256 IP address entries to the list (a single entry can
contain multiple IP addresses). The users from these IP addresses need to be specified in the
user list with the appropriate access rights. This is done from Setup > System Options >
Security > Users.
Referrals
To prevent unauthorized clients from including the video stream from the cameras into
external Web pages, check the Referrals checkbox and enter the IP address or Host name
of the computer that hosts the Web pages with the included video stream. Several IP
addresses/host names can be defined and are separated by semicolons (;). This option is
only applicable to Motion JPEG video streams.
AXIS 210/211 - System Options 35
Notes: •If the referrals feature is enabled and you wish to also allow normal access to the Live View
page, the product's own IP address or host name must be added to the list of allowed referrers.
•Restricting referrers has no effect on an MPEG-4 video stream. To restrict an MPEG-4 stream, IP
address filtering must be enabled.
•Restricting referrers is of greatest value when not using IP address filtering. If IP address filter-
ing is used, then the allowed referrers are automatically restricted to those allowed IP
addresses.
Date & Time Format Used in Images - specify the formats for the date and time (12h or
24h) displayed in the Live View video streams.
Use the predefined formats or use your own custom date and time formats. See Advanced
File Naming & Date/Time Formats in the help files for information on how to create
your own file formats.
IP Address Configuration
Your Axis network camera supports both IP version 4 and IP version 6. Both versions may
be enabled simultaneously, and at least one version must always be enabled.
When using IPv4, the IP address can be set automatically via DHCP, or a static IP address
can be set manually.
36 AXIS 210/211 - System Options
If IPv6 is enabled, your camera will receive an IP address according to the configuration in
the network router.
There are also options for setting up notification of changes in the IP address, and for
using the AXIS Internet Dynamic DNS Service. For more information on setting the IP
address, please see the online help.
Notes:
• DHCP is a protocol for automatic IP address assignment on a network. IP address assignment via DHCP may
lead to the situation where the IP address changes and you lose contact with the camera. Configure the
options for notification of IP address change (under Services) to receive notification from the camera when
the IP address changes.
• Alternatively, if your DHCP server can update a DNS server, you can access the AXIS 210/211 by host name
which is always the same, regardless of the IP address.
Services
Options for notification of IP address change - if the IP address for the video server
changes, e.g. automatically by DHCP, you can choose to be notified of the change. Click
Settings... and enter the required information.
AXIS Internet Dynamic DNS Service - If the AXIS 210/211 has been registered with the
Axis Internet Dynamic DNS service and the IP address for the product changes, the service
is updated to reflect the change. Check the box to enable/disable automatic updates.
The domain name currently registered at the Axis Internet Dynamic DNS service for your
product can at any time be removed. To do this click Settings... and follow the
instructions. For more information, please refer to the online help
DNS Configuration
DNS (Domain Name Service) provides the translation of host names to IP addresses on
your network.
Obtain DNS server address via DHCP - automatically use the DNS server settings provided
by the DHCP server. Click the View button to see the current settings.
Use the following DNS server address - enter the desired DNS server by specifying the
following:
Domain name - enter the domain(s) to search for the host name used by the AXIS
210/211. Multiple domains can be separated by semicolons (;). The host name is always the
first part of a Fully Qualified Domain Name, e.g. myserver is the host name in the Fully
Qualified Domain Name myserver.mycompany.com where mycompany.com is the
Domain name.
AXIS 210/211 - System Options 37
DNS servers - enter the IP addresses of the primary and secondary DNS servers.
NTP Configuration
The AXIS 210/211 can obtain the correct time from an NTP server. The address for the NTP
server can either be obtained via the DHCP server, or it can be entered manually.
Link-Local Address
This is enabled by default and assigns the AXIS 210/211 an additional IP address for use
with UPnP™. The AXIS 210/211 can have both a Link-Local IP and a static/DHCP-supplied
IP address at the same time - these will not affect each other.
HTTP
The default HTTP port number (80) can be changed to any port within the range
1024-65535. This is useful for e.g. simple security port mapping.
Broadband
(NAT) ISP
router
38 AXIS 210/211 - System Options
Notes: • For NAT traversal to work, this must also be supported by the broadband router.
• The broadband router has many different names: “NAT router”, “Network router“, Internet Gateway”,
“Broadband sharing device” or “Home firewall” but the essential purpose of the device is the same.
Enable/Disable - When enabled, the AXIS 210/211 will attempt to configure port mapping
in a NAT router on your network, using UPnP™. Note that UPnP™ must be enabled in the
camera (see System Options > Network > UPnP).
Use manually selected NAT router - Select this option to manually select a NAT router
and enter the IP address for the router in the field provided.
If a router is not manually specified, the AXIS 210/211 will automatically search for NAT
routers on your network. If more than one router is found, the default router will be
selected.
Alternative HTTP port - Select this option to manually define an external HTTP port. Enter
the port number in the field provided. If no port is entered here a port number will
automatically be selected when NAT traversal is enabled.
Notes: • An alternative HTTP port can be used/be active even if NAT traversal is disabled. This is useful if e.g. your
NAT router does not support UPnP and you need to manually configure port forwarding in the NAT router.
• If you attempt to manually enter a port that is already in use, another available port will automatically be
selected.
• When the port is selected automatically it will be displayed in this field. This can be changed by entering a
new port number and clicking Save.
RTSP
The RTSP protocol allows a connecting client to start an MPEG-4 stream. Enter the RTSP
port number to use. The default setting is 554.
FTP
The FTP server running in the AXIS 210/211 enables the upload of e.g. new firmware, user
applications, etc. Check the box to enable the service.
Network Traffic
The default setting is Auto-negotiate which means that the correct speed is automatically
selected. If necessary, you can set the connection speed by selecting it from the drop-down
list.
Maximum bandwidth - Specify, in Mbit/s or kbit/s, the maximum bandwidth the AXIS
210/211 will be allowed to use on your network. This is a useful function when connecting
the camera to busy or heavily loaded networks. The default setting is Unlimited.
Note: When using MPEG-4 as the video format, remember that setting a maximum bandwidth value here may
create problems for individual video streams if the maximum value is less than the sum of the bit rates set
for the video streams.
AXIS 210/211 - System Options 39
Network - SOCKS
SOCKS is a network proxy protocol. The cameras can be configured to use a SOCKS server
to reach networks on the other side of a firewall/proxy server. This functionality is useful if
the camera is located on a local network behind a firewall, but notifications, uploads,
alarms, etc., need to be sent to a destination outside the local network (e.g. to the Internet).
For more infomation on Quality of Service, please see the Axis support web at
www.axis.com/techsup
Network - UPnP™
The cameras includes support for UPnP™, which is enabled by default. If also enabled on
your computer, the camera will automatically be detected and a new icon will be added to
“My Network Places.”
Note: UPnP must also be enabled on your Windows XP computer. To do this, open the Control Panel from the
Start Menu and select Add/Remove Programs. Select Add/Remove Windows Components and open the
Networking Services section. Click Details and then select UPnP as the service to add.
Bonjour
Your Axis network camera includes support for Bonjour. When enabled, the camera is
automatically detected by operating systems and clients that support this protocol.
LED Settings
The Status indicator LED on the front of the camera can be set to flash at a configurable
interval (or to not light up at all) whenever the unit is accessed. For a listing of all LED
behavior, see page 8, or the online help.
Note: The LED does not flash when the stream is retrieved using MPEG-4 multicast.
Maintenance
• Restart - The camera is restarted without changing any of the settings. Use this method
if the unit is not behaving as expected.
• Restore - The unit is restarted and most current settings are reset to factory default val-
ues. The settings that will not be reset are as follows:
• the boot protocol (DHCP or static)
• the static IP address
• the default router
• the subnet mask
AXIS 210/211 - System Options 41
Support
The Support Overview page provides valuable information on troubleshooting and contact
information, should you require technical assistance.
System Overview - is a quick look over the camera’s status and settings. Information that
can be found here includes the camera’s Firmware version, IP address, Security, Event and
Image settings and Recent log items. Many of the captions are also links to the proper
Setup page to conveniently make adjustments in the cameras settings.
Logs & Reports - when contacting Axis support, please be sure to provide a valid Server
Report with your query.
Information - The Log file, the Server Report and the Parameter List all provide valuable
information for troubleshooting and when contacting Axis support.
Configuration
Log Level for Log Files - from the drop-down list, select the level of information to be
added to the Log file
Log Level for E-mail - from the drop-down list, select the level of information to send as
e-mail and enter the destination e-mail address.
Advanced
Scripting - this an advanced function that provides the means for customizing and using
scripts.
42 AXIS 210/211 - System Options
Caution!
The scripting function is a very powerful tool. Improper use may cause unexpected
behavior or even loss of contact with the unit. If a script does cause problems, reset the
unit to its factory default settings (in which case, a previously saved backup file will be
useful for returning the unit to its latest configuration). Axis strongly recommends that
you do not use this function unless you fully understand the consequences. Axis
support provides no assistance for customized scripts.
For more information, please visit the Developer pages at www.axis.com/developer
Plain Config - this function is for the advanced user with previous experience of
configuring Axis cameras. All parameters can be set and modified from this page. Help is
available via the links on the standard setup pages.
2 Auxiliary DC Power Input 7-20 VDC/max 5W. Electrically connected in parallel with the PS-K power
connector, this pin provides an auxiliary connector for mains power to the unit. If
the unit is powered via this pin, a fuse should be used (rating: 1A Slow).
This pin can also be used to power auxiliary equipment, max 100mA, but note that
this is not possible when the AXIS 211 is powered by PoE.
1 GND
use).
2. Push the cable into the connector and secure it by fastening the screw.
3. Once devices are connected, connect the terminal connector to the camera,
making sure that all cables are securely fastened.
Switch
3.3V Mode +
Power
Supply PS-K 9W - +
e.g., doorbell
Relay
GND 1
Device
4
AXIS 210/211 - Technical Specifications 45
Technical Specifications
Item Specification
Models • AXIS 210: indoor use only
• AXIS 211: Power over Ethernet, DC-Iris
Image sensor 1/4” Sony Wfine progressive scan RGB CCD
Lens • AXIS 210: 4.0 mm, F1.2, fixed iris, CS mount
• AXIS 211: 3.0 - 8.0 mm, F1.0, DC-iris, CS mount
Agle of view • AXIS 210: 48° horizontal
• AXIS 211: 27º-67º horizontal
Minimum illumination • AXIS 210: 1.0 lux, F1.2
• AXIS 211: 0,75 lux, F1.0
Video compression • Motion JPEG
• MPEG-4 Part 2 (ISO/IEC 14496-2), Profiles: ASP and SP
Resolutions 16 resolutions from 640 x 480 to 160 x 120 via API, 5 selections via
configuration web page.
Frame rate • Motion JPEG:
Up to 30 fps in all resolutions
• MPEG-4:
Up to 25 fps at 640x480
Up to 30 fps at 480x360 or lower
Video streaming • Simultaneous Motion JPEG and MPEG-4
• Controllable frame rate and bandwidth
• Constant and variable bit rate (MPEG-4)
Image settings • Compression levels: 11 (Motion JPEG)/23 (MPEG-4)
• Rotation: 90º, 180º, 270º
• Configurable color level, brightness, contrast, exposure, white balance, fine
tuning of behavior at low light
• Overlay capabilities: time, date, privacy mask, text or image
Shutter time 2 sec to 1/12500 sec
Security • Multiple user access levels with password protection
• IP address filtering
Users • 20 simultaneous users
• Unlimited users using multicast (MPEG-4)
Language support • English. Downloadable language files for French, German, Italian, Japanese and
(Web interface) Spanish are available at www.axis.com/techsup.
• Other language files may also be available
Alarm and event management • Events triggered by built-in motion detection, external input or according to a
schedule
• Image upload over FTP, email and HTTP Notification over TCP, email, HTTP and
external output
• Pre- and post alarm buffer: up to 1.2 MB (up to 40 sec of 320x240 video at 4
frames per sec)
Connectors • RJ-45 for Ethernet 10BaseT/100BaseTX
• Terminal block for 1 alarm input, 1 output and alternative power connection
Casing • Plastic
46 AXIS 210/211 - Technical Specifications
Item Specification
Processors and memory • CPU: ETRAX 100LX 32bit
• Video processing and compression: ARTPEC-2
• RAM: 16 MB
• Flash: 4 MB
• Battery backed up real-time clock
Power • 7-20 V DC max 7 W
• AXIS 211: PoE IEEE802.3af Class 2
Operating conditions • 5 - 45 ºC (41 – 113 ºF)
• Humidity 20 - 80% RH (non-condensing)
Installation, management and • AXIS Camera Management tool on CD and web-based configuration
maintenance • Configuration of backup and restore
• Firmware upgrades over HTTP or FTP, firmware available at www.axis.com
Video access from • Camera live view,
Web browser • Video recording to file (ASF),
• Sequence tour for up to 20 external Axis video sources,
• Customizable HTML pages
Minimum web browsing • Pentium III CPU 500 MHz or higher, or equivalent AMD,128 MB RAM, AGP
requirements graphics card 32 MB RAM, Direct Draw
• Windows XP, 2000, 2003 Server, DirectX 9.0 or later Internet Explorer 6.x or later
• For other operating systems and browsers see www.axis.com/techsup
System integration support • Open API for application integration including AXIS VAPIX API*, AXIS Media
Control SDK*, event trigger data in video stream
• Quality of Service (QoS) Layer 3, DiffServ Model
Embedded Linux operating system
* Available at www.axis.com
Supported protocols IPv4/v6, HTTP, TCP, QoS, RTSP, RTP, UDP, IGMP, RTCP, SMTP, FTP, ICMP DHCP,
UPnP, Bonjour, ARP, DNS, DynDNS, SOCKS
Item Specification
Approvals • EN 55022 Class B,
• EN 61000-3-2,
• EN 61000-3-3
• EN 55024,
• FCC Part 15 Subpart B Class B,
• ICES-003 Class B
• VCCI Class B,
• C-tick AS/NZS 3548,
• EN 60950
• Power supply: EN 60950, UL, cUL
Dimensions (HxWxD) and • AXIS 210: 38 x 88 x 157 mm (1.5” x 3.4” x 6.2”)
weight • AXIS 211: 38 x 95 x 178 mm (1.5” x 3.7” x 7.0”)
• 250 g (0.55 lb) excl. power supply
Important!
•The figures displayed here are the values as delivered by the camera. If other restrictions are
currently in force, (e.g. bandwidth limitation) these values might not correspond to those actu-
ally received by the client.
•For Motion JPEG, these values will be accurate as long as no frame rate limit has been specified.
AXIS 210/211 - Technical Specifications 49
Notes: • Setting the GOV structure to use “I-frames only” will increase the frame rate at the expense of the bit rate.
Bandwidth
As there are many factors that affect bandwidth, it is very difficult to predict the required
amounts. The settings that affect bandwidth are:
• the image resolution
• the image compression
• the frame rate
• the MPEG-4 object type
• the MPEG-4 GOV structure
• the maximum exposure time.
There are also factors in the monitored scene that will affect the bandwidth. These are:
• the amount of motion
• the image’s complexity
• the lighting conditions.
For MPEG-4, if there is only limited bandwidth available, and if this is more important
than the image quality, using a constant bit rate (CBR) is recommended. Use a variable bit
rate (VBR) if the image quality needs to be maintained at a higher level. If supported on the
network, consider also using MPEG-4 multicasting, as the bandwidth consumption will be
much lower.
50 AXIS 210/211 - Troubleshooting
Troubleshooting
1. Save the firmware file to your computer. The latest version of the firmware is
available free of charge from the Axis Web site at www.axis.com/techsup
2. Go to Setup > System Options > Maintenance in the camera’s web pages.
3. In the Upgrade Server section, browse to the desired firmware file on your
computer. Click Upgrade.
Notes: •After starting the upgrade process, always wait at least 5-10 minutes before restarting the
camera, even if you suspect the upgrade has failed.
•Your dealer reserves the right to charge for any repair attributable to faulty upgrading by the
user.
AXIS 210/211 - Troubleshooting 51
2. If the unit does not reply within a few seconds, restart it and wait for a reply. Press
CTRL+C to stop Ping.
3. Open a browser and type in the camera’s IP address. In the page that appears, use the
Browse button to select the upgrade file to use, e.g. axis210.bin or axis211.bin. Then
click the Load button to restart the upgrade process.
4. After the upgrade has completed (1-10 minutes), the unit will automatically restart and
show a steady green on the Power and Status LEDs and flashing green or amber on the
Network LED.
5. Referring to the installation guide, reinstall the camera.
If the emergency recovery procedure does not get the camera up and running again, please
contact Axis support at www.axis.com/techsup/
Axis Support
If you contact Axis support, please help us to help you solve your problems, by providing
the server report, the log file and a brief description of the problem.
Server Report - go to Setup > System Options > Support Overview. The server report
contains important information about the server and its software, as well as a list of the
current parameters.
The Log file is available from Setup > System Options > Logs & Reports. The Log file
records events in the unit since the last system restart and can be a useful diagnostic tool
when troubleshooting.
52 AXIS 210/211 - Troubleshooting
The IP address is being used by another Disconnect the camera from the network. Run the Ping command. (In a Command/DOS
device window, type ping and the IP address of the unit).
If you receive: Reply from <IP address>: bytes = 32; time = 10 ms..... - this means that
the IP address may already be in use by another device on your network. You must obtain
a new IP address and reinstall the unit.
If you see: Request timed out - this means that the IP address is available for use with
your camera. In this case, check all cabling and reinstall the unit.
Possible IP address conflict with The static IP address in the camera is used before the DHCP server sets a a dynamic
another device on the same subnet. address. This means that if the same default static IP address is also used by another
device, there may be problems accessing the camera. To avoid this, set the static IP
address to 0.0.0.0.
The camera cannot be accessed from a browser
The IP address has been changed by 1) Move the camera to an isolated network or to one with no DHCP or BOOTP server. Set
DHCP. the IP address again, using the AXIS IP Utility (see the Installation Guide) or the ARP/Ping
commands.
2) Access the unit and disable DHCP in the TCP/IP settings. Return the unit to the main
network. The unit now has a fixed IP address that will not change.
3) As an alternative to 2), if dynamic IP address via DHCP or BOOTP is required, select the
required service and then configure IP address change notification from the network set-
tings. Return the unit to the main network. The unit will now have a dynamic IP address,
but will notify you if the address changes.
Proxy server. If using a proxy server, try disabling the proxy setting in your browser.
Other networking problems. Test the network cable and connectors by connecting it to another network device, then
Ping that device from your workstation. See the instructions above.
Incorrect host name. Check that the host name and DNS server settings are correct. See the basic and
advanced TCP/IP settings.
Cannot send notifications, uploads, alarms, etc, to a destination outside the local network
Firewall protection. The camera can be configured to use a SOCKS server to reach networks on the other side
of a firewall/proxy server.
Camera is accessible locally, but not externally
Firewall protection. Check the Internet firewall with your system administrator.
Default routers required. Check if you need to configure the default router settings.
Poor or intermittent network connection.
Network switch. If using a network switch, check that the port on that device uses the same setting for
the network connection type (speed/duplex) as set in the advanced TCP/IP settings.
The Auto-Negotiate setting is recommended.
AXIS 210/211 - Troubleshooting 53
Poor rendering of MPEG-4 images. Color depth set incorrectly on clients. Set to 16-bit or 32-bit color.
If text overlays are blurred, or if there are other rendering problems, you may need to
enable Advanced Video Rendering. This is done on the MPEG-4 tab in the AMC control
panel applet.
Ensure that your graphics card is using the latest device driver. The latest drivers can
usually be downloaded from the manufacturer's web site.
If images are degrading, try decreasing the GOV length, see “Advanced Settings” on page
22.
Color saturation is different in MPEG-4 Modify the settings for your graphics adapter. Please see the adapter's documentation
and Motion JPEG. for more information.
The test image does not display as expected.
Image settings. Not all settings have an effect on the test image. For more information, see the help on
Image Settings.
The Power indicator is not constantly lit
Faulty power supply. Check that you are using an AXIS PS-K power supply.
The Status and Network indicator LEDs are flashing red rapidly
Hardware failure. Contact your Axis dealer.
The Status indicator LED is flashing red and the camera is inaccessible
A firmware upgrade has been inter- See the Emergency Recovery Procedure above.
rupted or the firmware has otherwise
been damaged.
Poor quality snapshot images
Screen incorrectly configured on your In Display Properties, configure your screen to show at least 65000 colors, i.e. at least
workstation. 16-bit. Using only 16 or 256 colors will produce dithering artifacts in the image.
Browser freezes
Netscape 7.x or Mozilla 1.4 (or later) Lower the image resolution.
can sometimes freeze on a slow com-
puter.
Problems uploading files
Limited space. There is only limited space available for the upload of your own files. Try deleting one or
more existing files, to free up space.
Missing images in uploads. This can occur when trying to use a larger image buffer than is actually available. Try
lowering the frame rate or the upload period.
Overlay is not displayed
Incorrect size or location of overlay. The overlay may have been positioned incorrectly. Refer to the online help for informa-
tion on the limitations when using image overlays and privacy masks.
Motion Detection triggers unexpectedly
Changes in luminance. Motion detection is based upon changes in luminance in the image. This means that if
there are sudden changes in the lighting, motion detection may be mistakenly triggered.
Lower the sensitivity setting to avoid problems with luminance.
For additional assistance, please contact your reseller or see the support pages on the Axis
Website at www.axis.com/techsup
AXIS 210/211 - Glossary of Terms 55
NWAY - A network protocol that automatically negotiates WAN - Wide-Area-Network. Similar to a LAN, but on a
the highest possible common transmission speed between larger geographical scale.
two devices. Web server - A program on a computer (server) providing
PAL - Phase Altering Line. PAL is the standard format used the resources (e.g. web pages) requested by the user (client).
for televisions in most of the world (other than the US,
Canada, and Japan).
PCM - Pulse Code Modulation. Analog signal converted
directly to a digital.
Ping - A small utility used for sending data packets to
network resources to check that they are working and that
the network is intact.
Pre/post alarm image - The images from immediately
before and after an alarm.
Protocol - A special set of rules governing how two entities
will communicate. Protocols are found at many levels of
communication, and there are hardware protocols and
software protocols.
Router - A device that determines the next network point to
which a packet should be forwarded on its way to its final
destination. A router is often included as part of a network
switch (see below).
RTP- Real-Time Transfer Protocol. A transfer protocol
designed for delivery of live contents, e.g. MPEG-4.
Simplex - In simplex operation, a network cable or
communications channel can only send information in one
direction.
SMTP - A common e-mail protocol.
SNMP - Simple Network Management Protocol. An
application layer protocol that facilitates the exchange of
management information between network devices. It is
part of the Transmission Control Protocol/Internet Protocol
(TCP/IP) protocol suite.
Subnet Mask - An IP address consists of two components:
the network address and the host address. “Subnetting’
enables a network administrator to further divide the host
part of the address into two or more subnets. The subnet
mask identifies the subnet to which an IP address belongs.
Switch - Whilst a simple hub transmits all data to all
devices connected to it, a switch only transmits the data to
the device it is specifically intended for.
TCP/IP - Transmission Control Protocol/Internet Protocol. A
suite of network protocols that determine how data is
transmitted. TCP/IP is used on many networks, including the
Internet. TCP keeps track of the individual packets of
information and IP contains the rules for how the packets
are actually sent and received.
URL - Uniform Resource Locator. An “address" on the
network.
Varifocal - A varifocal lens provides a wide range of focal
lengths, as opposed to a lens with a fixed focal length,
which only provides one.
AXIS 210/211 - Index 57
Index F
Factory Default Settings 42
Frame rate 20
A FTP Server 29
Accessing the video stream 16
Action 29 H
Action Buttons 12, 26 Host Name 37
Active/Inactive 26 HTML Examples 27
Administrator 18 HTTP 37
Advanced Simple profile 14 HTTP API 26
Alarm 32, 43 HTTP Server 29
AMC Viewer Toolbar 13
Auxiliary Power 43 I
AXIS 16 I/O Ports 40
AXIS Media Control 16 I/O Terminal Connector 8, 43
Include Windows 32
B Input 43
Backup 41 IP Address Filtering 34
Bandwidth 14, 49
Bit rate 14 L
Buffer Size 31 Live View 12, 18
Buffers 31 Live View Config 24
Logs & Reports 41
C
CGI links 26 M
Control Button 8, 42 Motion Detection 32
Custom settings 24 Motion JPEG 14
MPEG-4 5, 14
D MPEG-4 protocols 15
Date & Time 35 Multicasting 15
DC Power 43
DC-Iris 6 N
DNS Configuration 36 NAT Traversal 37
DNS Server 36, 37 NAT traversal 37
Domain Name 36 Network Connector 8
Network Settings 35
E NTP Configuration 37
Emergency Recovery 51 NTP Server 35
Event Servers 29
Event Types 30 O
Events 29 Other MPEG-4 clients 17
External Video 27 Output 43
External Video Source 12 Output Buttons 26
58 AXIS 210/211 - Index