Asnt Recer RT QB Level I
Asnt Recer RT QB Level I
2) Calculate the geometric unsharpness for 5 mm nominal single wall thick pipe
weld, of outer dia 2 inch with 3mm source whose distance from film is 14
inches.
a) 0.5 mm
b) 0.65 mm
c) 0.04 mm
d) 0.00157 in
e) Both c & d
Ref: Page no 33 Un sharpness para 2 , last line
Ans: a; Ug = Fxt /D, Here F is 3mm, t is 2 inch ie 50 mm and D is 14-2= 12 inch ie 300 mm
So Ug= 3 x 50 /300 = 0.5 mm
3) For 2 inch thick steel object being radiographed the size of hole visible is 8% of
job thickness the peni size is 50% of hole size the sensitivity indicated is:
a) 4 2T
b) 2 2T
c) 2 4T
d) 1 4T
e) None of the above
Ref: Hole Image Quality Indicator Page no 172 para 3, ASNT HAND BOOK.
Ans is a, Hole size is 8 % job thickness and peni size is 4 % job thickness .
So it is 4 -2T
1
Ans: a; 1.5 = (!00 % + Scattered % ) / 100 % , Assuming 100% is original
intensity for Narrow beam condition. So Scattered beam intensity comes to
about 50%
5) The level of sensitivity by the visibility of a penetrameter whose thickness equals
to 2% of specimen thickness and hole diameter 4% of specimen thickness
referred to:
a) 2 – 4T
b) 2 – 2T
c) 4 – 2T
d) T – 2T
Ref: Hole Image Quality Indicator Page no 172 para 3, ASNT HAND BOOK
Ans b – 2-@T
2
3
10) In Compton scattering for large angle scattering
a) Most of initial photon energy is given to the scattered photon
b) Most of the initial energy is given to the ejected orbital electron
c) Usually equally shared
d) It is a random process
Ref: Page 49, Compton Scattering, Last three lines
Ans : b
11) Which source is frequently used in industrial thickness and density gages
a) Ir 192
b) Coo 60
c) Cs 137
d) Se 75
Ref: Page 76, First Para , Last three line ASNT RT HAND BOOK
Ans c
4
15) Scintillation counter has
a) more sensitivity then ionization chamber
b) Less sensitivity than ionization chamber
c) It can detect only alpha particle not Gamma
d) They have opaque scintillating material
Ref: Page no 100, First para and Desirable Scintillator Characteristic Para in ASNT
RT HAND BOOOK
Ans a
5
20) Which imaging process involves more sequential steps
a) Analogue Radiography
b) Digital radiography
c) Computer Tomography
d) All
e) None
Ref: LEVEL III Guide Page no 85 first para first five lines
Ans C
6
25) Compton scattering is effective in
a) Low Z materials
b) High energy photons
c) Good at detecting opiate drugs
d) All
e) None
Ref: Page no 381, First column Second Para 13th line to 23 rd line,
ASNT RT HAND BOOK
Ans d
27) The target size of the flash photo devices are ----------, than compared to
conventional x-ray tubes I
a) approximately the same
b) much lower
c) Comparatively larger
d) Solely depend on geometric un-sharpness
Ref: Page no 409 Second column Point no4 ASNT RT HAND BOOK
Ans : c
7
30) Which is not the application of flash radiography
a) Imaging of ss cladded nuclear fuel elements
b) Ballistic research
c) Vibration study
d) All
e) None
Ref: Page no 412 and 413 Industrial Application and page no 409 firsyt Para 22 nd line
ASNT RT HAND BOOK
Ans e
31) Which formula to be used when SSD, source shift, sensor separation, Flaw shift
are given I
a) Rigid formula
b) Single marker formulae
c) Double marker formulae
d) Source side marker formulae ASNT RT HAND BOOK
Ref: Page no.42
Ans : a
8
35) For the same average energy which will give better quality for 0.75 “ steel plate
Radiography?
a) X- Ray Continuous spectrum
b) Gamma ray discrete Spectrum
c) Alpha Ray
d) All
e) None
Ref : Fig 1 , Page no 56, ASNT RT HAND BOOK
Ans : a
38) You have to view both high thickness and low thickness on the same radiograph So
Use High latitude film
a) Use Low latitude film
b) Use Fast film
c) Use Slow film
Ref
Ans : a
39) When you take some stainless steel casting (Cf8m Material) radiography by using
IR 192 for thin section you get graininess. To reduce use
a) Slow film
b) Fast Film
c) Decrease Ex time
d) Decrease Dev time
Ref
Ans a