A2fm, TTS
A2fm, TTS
2011
Replaces: 02.08
A2FM English
Series 6
Instruction manual
The data specified above serve to describe the
product. Should information be provided on use,
these are only examples of applications and
suggestions. Information from the catalog are not
assured properties. The information given does
not release the user from the obligation of own
judgment and verification. Our products are subject
to a natural wear and aging process.
Content
Content
1 About this manual......................................................................................5
1.1 Validity of the documentation.......................................................................5
1.2 Required and supplementary documentation..............................................5
1.3 Display of information...................................................................................6
1.3.1 Safety instructions........................................................................................6
1.3.2 Symbols.......................................................................................................7
1.3.3 Designations................................................................................................7
1.3.4 Abbreviations...............................................................................................7
2 Safety instructions.....................................................................................8
2.1 About this chapter........................................................................................8
2.2 Intended use................................................................................................8
2.3 Improper use................................................................................................8
2.4 Personnel qualifications...............................................................................9
2.5 General safety instructions...........................................................................9
2.6 Product-specific safety instructions............................................................10
2.7 Personal protective equipment...................................................................11
3 General instructions on damage to equipment and the product........ 12
4 Delivery contents.....................................................................................14
5 Product description.................................................................................15
5.1 Performance description............................................................................15
5.2 Product description....................................................................................15
5.2.1 Assembly of the axial piston unit................................................................15
5.2.2 Functional description................................................................................16
5.3 Product identification..................................................................................16
6 Transport and storage.............................................................................17
6.1 Transporting the axial piston unit...............................................................17
6.1.1 Transporting by hand.................................................................................17
6.1.2 Transporting with lifting device...................................................................17
6.2 Storing the axial piston unit........................................................................19
7 Installation................................................................................................21
7.1 Unpacking..................................................................................................21
7.2 Installation conditions.................................................................................21
7.3 Installation position.....................................................................................23
7.3.1 Below-reservoir installation (standard).......................................................23
7.3.2 Above-reservoir installation........................................................................24
7.4 Installing the axial piston unit.....................................................................25
7.4.1 Preparation.................................................................................................25
7.4.2 Dimensions................................................................................................25
7.4.3 General instructions...................................................................................25
7.4.4 Installation with coupling............................................................................26
7.4.5 Installation on a gearbox............................................................................27
7.4.6 Installation with cardan shaft......................................................................27
7.4.7 Completing installation...............................................................................28
7.4.8 Hydraulically connecting the axial piston unit.............................................28
7.5 Performing flushing cycle...........................................................................34
8 Commissioning........................................................................................35
8.1 First commissioning...................................................................................35
8.1.1 Filling the axial piston unit..........................................................................35
8.1.2 Testing the hydraulic fluid supply...............................................................36
8.1.3 Performing functional test..........................................................................37
8.2 Running-in phase.......................................................................................37
8.3 Recommissioning after standstill................................................................38
9 Operation..................................................................................................39
4/52 Bosch Rexroth AG A2FM Series 6 | RE 91001-01-B/08.2011
Content
Signal word
Type and source of danger
Consequences with noncompliance
ff Measure for danger prevention
ff <List>
1.3.2 Symbols
The following symbols mark notes that are not safety-relevant but which increase
the understanding of the documentation.
Table 3: Meaning of the symbols
Symbol Meaning
If this information is disregarded, the product can not be used
and/or operated to the optimum extent.
1.3.3 Designations
This documentation uses the following designations:
Table 4: Designations
Designation Meaning
A2FM Axial piston fixed motor, open and closed circuits
Protective plug Made out of plastic, not pressure-resistant, only for transportation
As umbrella term for “Axial piston fixed motor A2FM”, the designation “axial piston
unit” will be used in the following.
1.3.4 Abbreviations
This documentation uses the following abbreviations:
Table 5: Abbreviations
Abbreviation Meaning
DIN Deutsche Industrie Norm (German Institute for Standardization)
ISO International Organization for Standardization
RE Rexroth document in the English language
VDI 2230 Directive for the systematic calculation of high duty bolted
joints and joints with one cylindrical bolt from the VDI
(Verein Deutscher Ingenieure – Association of German Engineers)
8/52 Bosch Rexroth AG A2FM Series 6 | RE 91001-01-B/08.2011
Safety instructions
2 Safety instructions
The axial piston unit is only intended for professional use and not for private use.
Intended use includes having completely read and understood this
documentation, especially chapter 2 “Safety instructions”.
Safety instructions
•• Using the axial piston unit when the exterior pressure is greater than the interior
pressure (case pressure)
•• Using the axial piston unit in explosive environments unless the
component or machine/system has been certified as compliant with the
ATEX directive 94/9/EC
•• Using the axial piston unit in an aggressive atmosphere
•• Using the axial piston unit in aircraft or space craft
Bosch Rexroth offers training support for special fields. You can find an
overview of the training contents on the Internet at:
http://www.boschrexroth.de/didactic.
Safety instructions
•• You may only commission the product if it has been determined that the end
product (e.g. machinery or a system) into which the Rexroth products are
installed complies with the country-specific provisions, safety regulations and
standards of the application.
WARNING
Danger from suspended loads!
Danger to life or risk of injury, damage to equipment!
Improper transportation may cause the axial piston unit to fall down lead to
injuries e.g. crushing or broken bones or damage to the product.
ff Make certain that the forklift truck or lifting device has adequate lifting
capacity.
ff Never stand under or put you hands under suspended loads.
ff Ensure your position is stable during transportation.
ff Use your personal protective equipment (e.g. safety glasses, safety gloves,
suitable working clothes, safety shoes).
ff Use suitable lifting devices for transportation.
ff Observe the prescribed position of the lifting strap.
ff Observe the national laws and regulations on work and health protection
and transportation.
Pressurized machine/system!
Danger to life or risk of injury, serious injuries when working on machines/
systems not shutdown! Damage to equipment!
ff Protect the complete system against being energized.
ff Make sure that the machine/system is depressurized. Please follow the
machine/system manufacturer’s instructions.
ff Do not disconnect any line connections, connections and components when
the machine/system is pressurized.
ff Switch off all power-transmitting components and connections (electric,
pneumatic, hydraulic) in accordance with the manufacturer’s instruction and
secure them against being switched back on.
Electrical voltage!
Risk of injury due to electric shock or damage to equipment!
ff Always set up the relevant part of the machine/system so that it is free of
electrical voltage before you install the product or when connecting and
disconnecting plugs. Protect the machine/system against being energized.
RE 91001-01-B/08.2011 | A2FM Series 6 Bosch Rexroth AG 11/52
Safety instructions
CAUTION
High noise development in operation!
Danger of hearing damage, deafness!
The noise emission of axial piston units depends on speed, operating pressure
and installation conditions. The sound pressure level may rise above 70 dBA
during normal application conditions.
ff Always wear hearing protection when in the vicinity of the operating axial
piston unit.
NOTE
Danger from improper handling!
Product can be damaged!
ff Do not expose the product to an impermissible mechanical load.
ff Never use the product as a handle or step.
ff Do not place/lay any objects on the product.
ff Do not strike the drive shaft of the axial piston unit.
ff Do not set/place the axial piston unit on the drive shaft.
ff Do not strike sensitive fittings (e.g. sensors or valves).
ff Do not strike sealing surfaces (e.g. service line ports).
ff Leave the protective covers on the axial piston unit until shortly before the
lines are connected.
NOTE
Contamination of the hydraulic fluid!
The cleanliness of the hydraulic fluid has a considerable impact on the
cleanliness and service life of the hydraulic system. Premature wear and
malfunctions!
ff Make sure that the working environment at the installation site is fully free
of dust and foreign substances in order to prevent contaminants, such as
welding beads or metal cuttings, from getting into the hydraulic lines and
causing product wear or malfunctions. The axial piston unit must be installed
in a clean condition.
ff Use only clean connections, hydraulic lines and attachments
(e.g. measuring equipment).
ff No contaminants may enter the connections when they are plugged.
ff Before commissioning, make certain that all hydraulic connections are
tight and that all of the connection seals and plugs are installed correctly to
ensure that they are leakproof and fluids and contaminants are prevented
from penetrating the product.
ff Use a suitable filter system to filter hydraulic fluids during filling to minimize
solid impurities and water in the hydraulic system.
Improper cleaning!
Product can be damaged!
ff Plug all openings with the appropriate protective equipment in order to
prevent detergents from entering the hydraulic system.
ff Never use solvents or aggressive detergents. Use only water and,
if necessary, a mild detergent to clean the axial piston unit.
ff Do not point the power washer at sensitive components, e.g. shaft seal,
electrical connections and components.
ff Use lint-free cloths for cleaning.
Delivery contents
4 Delivery contents
2
2
2 1
1
Fig. 1: Axial piston unit with service line ports at the side (left figure) and rear
(right figure)
Product description
5 Product description
2
1
3
Product description
11
12
Rexroth
DE - 89275 Elchingen
CNR: X1234567890Y
Typ: A2FM80/61W-VAB010
10 MNR: R90XXXXXXX SC: X 2
9 SN: 12345678 7202 3
FD: 2011W30 4
Rotation:
8 m XXX kg
5
Made in Germany 6
Size 90 107 125 160 180 200 250 355 500 710 1000
Ground kg 23 32 32 45 45 66 73 110 155 325 336
Width mm The dimensions vary with the unit type. The values applicable for
your axial piston unit can be found in the installation drawing
Height mm
(request if necessary).
Depth mm
ff For all female threads, use a threaded plug from the same system of units and
of the correct size.
ff To do this, screw a ring screw completely into the thread on the drive shaft.
The thread sizes is stated in the installation drawing.
ff Make sure that the ring screw can bear the total weight of the axial piston unit
plus 20%.
You can hoist the axial piston unit as shown in Fig. 4 with the ring screw screwed
into the drive shaft.
ff Place the lifting strap around the axial piston unit in such a way that it passes
over neither the attachment parts (e.g. valves) nor such that the axial piston
unit is hung from attachment parts (see Fig. 5).
After delivery The axial piston units are provided ex-works with corrosion protection packaging
(corrosion protection film).
The following table lists the maximum permissible storage times for an originally
packed axial piston unit as per data sheet RE 90312.
Table 7: Storage time with factory corrosion protection
Standard Long-term
Storage conditions
corrosion protection corrosion protection
Closed, dry room, uniform Maximum 12 months Maximum 24 months
temperature between +5 °C
and +20 °C. Undamaged
and closed corrosion
protection film.
After expiry of the maximum storage time, we recommend that you have the
axial piston unit inspected by your responsible Bosch Rexroth Service partner.
In the event of questions regarding repair and spare parts, contact your
responsible Bosch Rexroth Service partner or the service department of the
manufacture’s plant for the axial piston unit, see chapter “10.5 Spare parts” for
further information.
20/52 Bosch Rexroth AG A2FM Series 6 | RE 91001-01-B/08.2011
After removal If a dismounted axial piston unit is to be stored, it must be preserved against
corrosion for the duration of the storage.
The following instructions only refer to axial piston units which are operated
with a mineral-oil based hydraulic fluid. Other hydraulic fluids require
preservation methods that are specifically designed for them. In such a case,
consult with Bosch Rexroth Service, see chapter 10.5 “Spare parts” for
address.
Installation
7 Installation
Prior to installation, the following documents must be available:
•• Installation drawing for axial piston unit (can be obtained from your responsible
contact person at Bosch Rexroth)
•• Hydraulic circuit diagram for the axial piston unit (in the installation drawing)
•• Hydraulic circuit diagram for the machine/system (available from the machine/
system manufacturer)
•• Order confirmation (contains the order-related technical data for your axial
piston unit)
•• Data sheet of the axial piston unit (contains the permissible values of technical
data)
7.1 Unpacking
The axial piston unit is delivered in a corrosion protection film made of
polyethylene material (PE).
CAUTION! Danger from parts falling out!
If the packaging is not opened correctly, parts may fall out and damage the parts
or even cause injuries!
ff Place the packaging on a flat and solid surface.
ff Only open the packaging from the top.
Installation
ff Make sure that the reservoir and return lines lead into the reservoir below the
minimum fluid level in all operating conditions. You prevent foam formation by
doing this.
ff Make sure that the working environment at the installation site is fully free of
dust and foreign substances. The axial piston unit must be installed in a clean
condition. Dirt contamination in the hydraulic fluid can seriously impair the
function and service life of the axial piston unit.
ff Use lint-free cloths for cleaning.
ff Use suitable mild detergents to remove lubricants and other difficult-to-remove
contamination. Cleaning agents must not enter the hydraulic system.
RE 91001-01-B/08.2011 | A2FM Series 6 Bosch Rexroth AG 23/52
Installation
1 2
ht min ht min
hmin hmin
T1 T2
T2 T1
3 4
ht min ht min
hmin hmin
R/U
T1
T2
T2
T1
Installation
5 6
L1 L1
T1 T2
T2
T1
ht min ht min
hmin hmin
7 8
L1
R/U
L1 T1
T2
0.5 bar
T2 T1
ht min ht min
hmin hmin
Installation
7.4.1 Preparation
1. Compare the material number and designation (ordering code) with the details
in the order confirmation.
If the material number for the axial piston unit does not correspond to the one
in the order confirmation, contact Bosch Rexroth Service for clarification, see
chapter “10.5 Spare parts” for address.
2. Before installing, completely empty the axial piston unit to prevent mixing with
the hydraulic fluid used in the machine/system.
L
W R
The direction of rotation as specified on the name plate, see chapter 5.3
“Identification of the product”, is the direction of rotation of the axial piston unit
as viewed to the drive shaft.
7.4.2 Dimensions
The installation drawing contains the dimensions for all connections and ports on
the axial piston unit. Also observe the manuals provided by the manufacturers of
the other hydraulic components when selecting the required tools.
Installation
•• V-belt drives without automatic clamper are also critical with regard to speed
variations and torsional vibrations. These can also lead to leakages on the shaft
seal ring.
An automatic clamper can lessen the speed variations and vibrations and thus
avoid consequential damage.
–– When using toothed belts or v-belts to transfer the input or output drive,
always use an automatic tensioning device.
•• On the input or output drive of an axial piston unit, a cardan shaft may cause
vibrations and impermissible rotary angle accelerations. Depending on the
frequency and temperature, they may result in leakage on the shaft seal and
damage to the rotary group.
•• When multiple units are combined, make sure that the case pressure of
each unit is not exceeded. If there are pressure differences at the reservoir
ports of the units, the complete reservoir line must be changed so that the
lowest permissible case pressure of all connected units is not exceeded in
any situation. If this is not possible, separate reservoir lines must be laid as
required.
The installation method for the axial piston unit depends on the connecting
elements to the output side. The following descriptions explain the installation of
the axial piston unit:
•• with a coupling
•• on a gearbox
1. Install the specified coupling half onto the drive shaft of the axial piston unit
according to the instructions of the coupling manufacturer.
The drive shaft of the axial piston unit is equipped with a threaded bore. Use
this threaded bore to pull the coupling element onto the drive shaft. The size
of the threaded bore can be seen in the installation drawing.
Installation
7. Align the drive shaft of the axial piston unit and the drive shaft of the machine
or system so that there is no angular deviation.
8. Make certain that no impermissible axial and radial forces act on the drive
shaft.
9. Details on the required tools and tightening torques for the fixing screws are
available from the machine/system manufacturer.
10. When using flexible couplings, check that the output drive is free of resonance
after completing the installation.
For attachment via gear wheel or No gearing forces higher than the permissible axial and radial forces are to act on
helically-toothed shaft the shaft, if necessary the gear wheel must be supported separately at the
gearbox output.
Installation
2
2 1
1
The following information only applies to fixed motors with pressure-relief valve.
The adjusting screws are protected against unauthorized resetting by means
of protective caps. Removal of the protective caps will void the warranty. If you
need a modification of the setting, please contact your responsible Bosch
Rexroth Service (address as to chapter “10.5 Spare parts”).
Installation
Notes on routing the lines Observe the following notes when routing the pressure and reservoir lines.
•• Lines and hoses must be installed without pre-charge pressure, so that no
further mechanical forces are applied during operation that will reduce the
service life of the axial piston unit and, if applicable, the entire machine/system.
•• Use suitable seals as sealing material.
•• Pressure line
–– For the pressure lines, use only pipes, hoses and connecting elements
rated for the operating pressure range specified in data sheet RE 91001
(see table 12).
•• Reservoir line
–– Always route the reservoir lines so that the case is constantly filled with
hydraulic fluid and to ensure that no air gets through the shaft seal even
during extended standstill periods.
–– The case internal pressure must not exceed the limit values listed for the axial
piston unit in the data sheet under any operating conditions.
–– The reservoir line joint in the reservoir must always be below the minimum
fluid level under all conditions (see chapter “7.3 Installation position”).
Risk of mix-ups with The axial piston units are used in application areas with metric as well as with the
threaded connections Anglo-American (inch) system of units.
Both the system of units as well as the size of threaded hole and threaded plug
(e.g. locking screw) must match.
Due to the limited options for visually detecting differences, there is a risk of
mix‑ups.
Warning! Leaking or popped-out threaded plugs!
If a threaded plug which is of a different measurement system and size with
respect to the female thread is pressurized, the threaded plug may loosen itself
or even be ejected from the hole in a projectile-like manner. This can result in
serious injury and damage to equipment. Hydraulic fluid can be discharged from
this leakage point.
ff Use the drawings (installation drawing/data sheet) to determine the required
threaded plug for each fitting.
ff Make certain that there are no mix-ups when installing fittings, fixing screws
and threaded plugs.
ff For all female threads, use a threaded plug from the same system of units and
of the correct size.
30/52 Bosch Rexroth AG A2FM Series 6 | RE 91001-01-B/08.2011
Installation
Connecting line to pressure-relief Please note the following information concerning the version with port plate 192.
valve with pressure cut-in stage
ff When screwing in and tightening the connection line to port PSt, the nut (1) on
the pressure-relief valve with pressure cut-in stage (2) must be braced with
WAF 24. Observe the manufacturer’s instructions regarding tightening torques
for the used connection line. The maximum permissible tightening torque at
the threaded hole (40 Nm) must not be exceeded.
PSt
1
Installation
Fixing the counterbalance valve Observe the following notes concerning the version with counterbalance valve
(port plate 181).
When delivered, the counterbalance valve is attached to the motor using tacking
screws (transport protection). The tacking screws must not be removed while
fixing the service lines! If the counterbalance valve and motor are delivered
separately, the counterbalance valve must first be attached to the motor port plate
using the provided tacking screws. The final fastening of the counterbalance valve
on the motor is performed by bolting the SAE flange with the following screws:
6 screws (1, 2, 3, 4, 5, 8) length B1+B2+B3
2 screws (6, 7) length B3+B4
Tighten the screws in two steps in the specified sequence from 1 to 8
(see diagram below).
ff In the first step, tighten the screws with half the tightening torque; in the
second step, tighten with the maximum tightening torque (see table 10).
2 4
B1
2)
6 8
7 5
2)
B2
3 1
B4
B3
1)
Y
1) SAE flange
2) Tacking screw (M6 x 1, length = B1 + B2, DIN 912)
Fig. 11: Fixing the counterbalance valve
The SAE flange and corresponding fixing screws are not included in the
delivery contents.
Installation
Port overview
T1 T1
T2
T2
B B
A
T1 T1
T2
T2 B
A
T1
T1
B
A
T2
T2
B
S1 PSt
PSt
T1
T1
B
A
MA
T2
T2
MB B
Fig. 15: Overview of ports A2FM with pressure relief valve, service line ports at bottom
RE 91001-01-B/08.2011 | A2FM Series 6 Bosch Rexroth AG 33/52
Installation
Installation
Table 13: Tightening torques of the female threads and threaded plugs
Ports Maximum permissible Required
WAF hexagon socket for
tightening torque of the tightening torque of the
Standard Thread size the threaded plugs
threaded holes MG max threaded plugs MV
DIN 3852 M10 x 1 30 Nm 12 Nm 5 mm
M12 x 1.5 50 Nm 25 Nm 6 mm
M14 x 1.5 80 Nm 35 Nm 6 mm
M16 x 1.5 100 Nm 50 Nm 8 mm
M18 x 1.5 140 Nm 60 Nm 8 mm
M22 x 1.5 210 Nm 80 Nm 10 mm
M26 x 1.5 230 Nm 120 Nm 12 mm
M27 x 2 330 Nm 135 Nm 12 mm
M33 x 2 540 Nm 225 Nm 17 mm
M42 x 2 720 Nm 360 Nm 22 mm
DIN ISO 228 G1/41) 40 Nm – –
1) Connecting thread on pressure relief valve, see chapter 7.4.8 “Hydraulically connecting the axial piston unit”.
Commissioning
8 Commissioning
WARNING
Danger while working in the danger zone of a machine/system!
Danger to life, risk of injury or serious injuries!
ff Pay attention to and rectify potential danger sources before operating the
axial piston unit.
ff Nobody may stand in the danger zone of the machine/system.
ff The emergency stop button for the machine/system must be within the
operator’s reach.
ff Always follow the instructions of the machine/system manufacturer during
commissioning.
CAUTION
Commissioning of an incorrectly installed product!
Risk of injury and damage to equipment!
You can injure yourself on incorrectly installed products or damage the product.
ff Make sure that all electrical and hydraulic ports are connected or plugged.
ff Only commission a completely installed product.
ff Connect the gauge for the operating pressure and case pressure to the
specified measuring points on the axial piston unit or in the hydraulic system,
to check the technical data at first operation.
ff During the commissioning process, monitor the temperature of the hydraulic
fluid in the reservoir to ensure that it lies within the permissible viscosity limits.
Commissioning
1. Place a drip tray under the axial piston unit to collect any hydraulic fluid that
may escape.
2. Fill and air bleed the axial piston unit via the appropriate ports, see chapter
“7.3 Installation position”. The hydraulic lines of the system must also be filled.
3. When using a shut-off valve in the reservoir line, only operate the axial piston
unit when the shut-off valves are open.
Commissioning
WARNING
Incorrectly connected axial piston unit!
Mixing up the ports will lead to malfunctions (e.g. lift instead of lower) and thus
to corresponding danger to persons and equipment!
ff Before the functional test, check whether the piping specified in the hydraulic
circuit diagram has been installed.
Once you have tested the hydraulic fluid supply, you must perform a functional
test on the machine/system. The functional test should be performed according to
the instructions of the machine/system manufacturer.
The axial piston unit is checked for functional capability before delivery according
to the technical data. During commissioning, it must be ensured that the axial
piston unit was installed properly in the machine/system.
ff After starting the engine, check in particular the specified pressures,
e.g. system pressure, boost pressure and case pressure.
ff If necessary, disconnect the gauge and plug the ports with threaded plugs.
NOTE
Damage to equipment by insufficient viscosity!
An increased hydraulic fluid temperature may reduce the viscosity values
by too much and damage the product!
ff Monitor the operating temperature during the running-in phase,
e.g. by measuring the case drain temperature.
ff Reduce the loading (pressure, rpm) of the axial piston unit if impermissible
operating temperatures and/or viscosities occur.
ff Operating temperatures that are too high indicate faults that have to be
analyzed and cleared.
The bearings and sliding surfaces are subject to a running-in phase. The
increased friction at the start of the running-in phase results in increased heat
development which decreases with increasing operating hours. The volumetric
and mechanical-hydraulic efficiency increases as well through the conclusion of
the running-in phase of approx. 10 operating hours.
To ensure that contamination in the hydraulic system does not damage the
axial piston unit, Bosch Rexroth recommends the following procedure after
the running-in phase:
ff After the running-in phase, have a hydraulic fluid specimen analyzed for the
required cleanliness level.
ff Change the hydraulic fluid if the required cleanliness level is not reached.
If a laboratory test is not carried out after the running-in phase, Bosch Rexroth
recommends the hydraulic fluid be changed.
38/52 Bosch Rexroth AG A2FM Series 6 | RE 91001-01-B/08.2011
Commissioning
Operation
9 Operation
The product is a component which requires no settings or changes during
operation. For this reason, this chapter of the manual does not contain any
information on adjustment options. Use the product only within the performance
range provided in the technical data. The machine/system manufacturer is
responsible for the proper project planning of the hydraulic system and its control.
40/52 Bosch Rexroth AG A2FM Series 6 | RE 91001-01-B/08.2011
NOTE
Inspection and maintenance work carried out too late!
Damage to equipment!
ff Carry out the specified inspection and maintenance work at the intervals
described in this manual.
NOTE
Damage to seals and electrical system by mechanical effects!
The water jet of a power washer may damage the seals and electrical system
of the axial piston unit!
ff Do not point the power washer at sensitive components, e.g. shaft seal,
electrical connections and components.
For cleaning and care of the axial piston unit, observe the following:
ff Check whether all seals and fittings on the connections are securely seated
to ensure that no moisture can penetrate into the axial piston unit during
cleaning.
ff Use only water and, if necessary, a mild detergent to clean the axial piston
unit. Never use solvents or aggressive detergents.
ff Remove external coarse dirt and keep sensitive and important components,
such as solenoids, valves, displays and sensors, clean.
RE 91001-01-B/08.2011 | A2FM Series 6 Bosch Rexroth AG 41/52
10.2 Inspection
In order to enable long and reliable operation of the axial piston unit, Bosch
Rexroth recommends testing the hydraulic system and axial piston unit on a
regular basis, and documenting and archiving the following operating conditions:
Table 14: Inspection schedule
Task to be carried out Interval
Hydraulic Check level of hydraulic fluid in the reservoir. Daily
system
Check the operating temperature at a Weekly
comparable load condition at the reservoir
port and in the reservoir.
Conduct analysis of hydraulic fluid: viscosity, Yearly or every 2000
aging and dirt contamination operating hours
(whichever occurs
first)
Axial piston unit Check axial piston unit for leakage. Daily
Early detection of hydraulic fluid loss can help
to find errors on the machine/system and to
rectify them. For this reason, Bosch Rexroth
recommends that the axial piston unit and
system are always kept in a clean condition.
Check axial piston unit for unusual noise Daily
development.
Check fasteners for tight seating. Monthly
All fasteners have to be checked when the
hydraulic system is switched off, depressurized
and cooled down.
10.3 Maintenance
The axial piston unit is low maintenance when used properly.
The service life of the axial piston unit is heavily dependent on the quality of the
hydraulic fluid. For this reason, we recommend changing the hydraulic fluid at
least once per year or every 2000 operating hours (which ever occurs first) or
having it analyzed by the hydraulic fluid manufacturer or a laboratory to determine
its suitability for further use.
The service life of the axial piston unit is limited by the service life of the bearings
fitted. The service life based on the load cycle can be requested from the
responsible Bosch Rexroth Service partner, see chapter 10.5 “Spare parts” for
address. Based on these details, a maintenance period is to be determined by
the system manufacturer for the replacement of the bearings and included in the
maintenance schedule of the hydraulic system.
10.4 Repair
Bosch Rexroth offers a comprehensive range of services for the repair of Rexroth
axial piston units.
Repairs on the axial piston unit may only be performed by service centers certified
by Bosch Rexroth.
ff Use exclusively original spare parts from Rexroth to repair the Rexroth axial
piston units, otherwise the functional reliability of the axial piston unit can not
be assured and you lose your entitlement under warranty.
CAUTION
Use of unsuitable spare parts!
Spare parts that do not meet the technical requirements specified by Bosch
Rexroth may cause personal injury or property damage!
ff Use exclusively original spare parts from Rexroth to repair the Rexroth axial
piston units, otherwise the functional reliability of the axial piston unit can not
be assured and you lose your entitlement under warranty.
The spare parts lists for axial piston units are order specific. When ordering spare
parts, quote the material and serial number of the axial piston unit as well as the
material numbers of the spare parts.
Address all questions regarding spare parts to your responsible Bosch Rexroth
Service partner or the service department of the manufacture’s plant for the axial
piston unit.
Details on the manufacture’s plant are available on the axial piston unit’s name
plate.
Bosch Rexroth AG
Glockeraustraße 4
D-89275 Elchingen, Germany
Tel. +49-7308-82-0
Fax +49-711-811-513-9382
[email protected]
Bosch Rexroth AG
An den Kelterwiesen 14
72160 Horb a.N., Germany
Tel. +49-7451-92-0
Fax +49-711-811-513-9382
[email protected]
Disposal
12 Disposal
Careless disposal of the axial piston unit, the hydraulic fluid and the packaging
material could lead to pollution of the environment.
Observe the following points when disposing of the axial piston unit:
1. Completely empty the axial piston unit.
2. Dispose of the axial piston unit and packaging material in accordance with the
national regulations in your country.
3. Dispose of the hydraulic fluid according to the national regulations of your
country. Also observe the applicable safety data sheet for the hydraulic fluid.
4. Remove the axial piston unit into its individual parts and properly recycle these
parts.
5. Separate according to, for instance:
–– Cast parts
–– Steel
–– Aluminum
–– Non-ferrous metal
–– Electronic waste
–– Plastic
–– Seals
Troubleshooting
14 Troubleshooting
The following table may assist you in troubleshooting. The table makes no claim
for completeness.
In practical use, problems which are not listed here may also occur.
ff Try to get a clear idea of the error cause. Directly ask the (machine) operator.
ff Document the work carried out.
ff If you cannot rectify the error, contact one of the contact addresses which can
be found under:
www.boschrexroth.com/addresses.
46/52 Bosch Rexroth AG A2FM Series 6 | RE 91001-01-B/08.2011
Troubleshooting
Improper fixing of the axial piston unit. Check the fixing of the axial piston unit
according to the specifications of the
machine/system manufacturer. Observe
tightening torques.
Improper fixing of the attachment parts, Fix attachment parts according to the
e.g. coupling and hydraulic lines. information provided by the coupling or
fitting manufacturer.
Mechanical damage to the axial piston unit Exchange axial piston unit,
(e.g. bearing damage). contact Bosch Rexroth Service.
Pressure/flow fluctuations Axial piston unit not or insufficiently air bled. Completely air bleed axial piston unit.
Operational data not achieved Insufficient flow at hydraulic pump. Check function of the hydraulic pump.
Technical data
15 Technical data
The permissible values of the technical data of your axial piston unit can be found
in data sheet RE 91001.
The data sheet can be found on the internet at
www.boschrexroth.com/axial-piston-motors
The order-related technical data of your axial piston unit can be found in the order
confirmation.
16 Appendix
Alphabetical index
17 Alphabetical index
A L
Abbreviations 7 Lifting device 17
Address directory 47 Lifting strap 18
Assembly 15
M
B Maintenance 40, 41
Below-reservoir installation 23 Malfunction table 46
C N
Care 40 Name plate 16
Circuit
closed 15
O
open 15
Cleaning 40 Operation 39
Commissioning 35
First 35 P
Connecting
Performance description 15
Hydraulic 28
Piston 15
Conversion 44
Port overview 32
Corrosion protection 19
Port plate 15
Corrosion protection film 19
Product description 15
Cylinder 15
Q
D
Qualifications 9
Damage to equipment 12
Delivery contents 14
Designations 7 R
Dimensions 17, 25 Recommissioning 38
Direction of rotation 25 After standstill 38
Disposal 44 Removal 43
Drive shaft 15 Performing 43
Preparing 43
F Repair 41
Replacement 43
Filling 35
Required documentation 5
Flushing cycle 34
Ring screw 17
Functional description
Running-in phase 37
Motor function 16
Functional test 37
S
I Safety instructions 8
General 9
Identification 16
Product-specific 10
Inspection 41
Signal word 6
Installation 21, 25
Spare parts 42
Completing 28
Storage 17
General instructions 25
Storage time 19
On a gearbox 27
Storing 19
Preparation 25
Symbols 7
With coupling 26
Installation conditions 21
Installation Position
Below-reservoir installation 23
Instructions
General 25
Intended use 8
RE 91001-01-B/08.2011 | A2FM Series 6 Bosch Rexroth AG 49/52
Alphabetical index
T
Technical data 47
Tightening torques 33
Tools 43
Transport 17
With lifting strap 18
With ring screw 17
Transporting 17
Transport protection 28
Troubleshooting 45
U
Unpacking 21
W
Warranty 19, 35, 44
Warranty rights 28
Weights 17
50/52 Bosch Rexroth AG A2FM Series 6 | RE 91001-01-B/08.2011
RE 91001-01-B/08.2011 | A2FM Series 6 Bosch Rexroth AG 51/52
Bosch Rexroth AG
Axial piston units
Glockeraustrasse 4
89275 Elchingen
Germany
Tel. +49-7308-82-0
Fax +49-7308-72-74
[email protected]
www.boschrexroth.com/axial-piston-motors
Bosch Rexroth AG
Axial piston units
An den Kelterwiesen 14
72160 Horb a.N.
Germany
Tel. +49-7451-92-0
Fax +49-7451-82-21
[email protected]
www.boschrexroth.com/axial-piston-motors
Subject to change
Printed in Germany
RE 91001-01-B/08.2011