Professional Documents
Culture Documents
Hubregt Zorki 4 CLA PDF
Hubregt Zorki 4 CLA PDF
CLA
APRIL 5 2020
Hubregt Photography
Hubregt J. Visser
1
© 2020, Hubregt J. Visser All Rights Reserved
2
Contents
1. Introduction 3
2. The Camera 5
3. History 6
4. Before Dismantling the Camera 8
5. Removing the Top 10
6. Removing the Flash-Synch-Switch 18
7. Removing, Cleaning and Lubricating the Slow-Speed-Mechanism 21
8. Lubricating the Shutter Speed Selector and Second Curtain Release Arm 27
9. Cleaning and Lubricating the Shutter-Rewind Mechanism 31
10. Removing the Shutter Crate from the Body 37
11. Removing the Crate Front and Light Baffles 43
12. A Brief Moment of Despair 45
13. Cleaning and Lubricating the Shutter and Film Transport Mechanism 46
14. Reassembly 52
15. Reassembly of the Slow-Speed-Mechanism 64
16. Shutter Curtain Tension Adjustment 68
17. Cleaning the Optical System 72
18. Putting the Top Back On 74
19. Checking the Shutter Operation 77
20. Test Shots 83
21. Conclusion 85
3
1. Introduction
And warning
In this document I describe how I have Cleaned, Lubricated and Adjusted (CLA’d) a 1961
Zorki-4 rangefinder camera.
I have had no training as a camera repair technician. Most probably, some - or all - of
my techniques and procedures will be frowned upon by a proper repair technician.
Notwithstanding that, the many pictures I have taken and figures I have drawn during
the dismantling and reassembly of the camera may be useful to a wide community. In
my favor I can report that I started with a camera with lagging and sometimes stuck
shutter curtains and that I ended up with a fully functional camera.
For dismantling and reassembling my Zorki-4, I have made use of information I have
found by searching the internet. My main sources of information have been a post by
Mike Eckman: https://www.mikeeckman.com/2015/11/zorki-4-v2-1961/ and a thread
on the rangefinder forum:
https://www.rangefinderforum.com/forums/showthread.php?t=33914 (look here for
the same information in one PDF file: https://fotoguru.nl/wp-
content/uploads/2019/05/Zorki-4K-CLA-How-to.pdf). Furthermore I have used
http://rick_oleson.tripod.com/index-58.html and the book “All you need to know
about the design and repair of Russian cameras” by Isaak S. Maizenberg.
My advice is to use these documents as well and combine the information and pictures
found there and here to make your job easier. As always in disassembling a camera,
make a lot of pictures of every disassembly step and make drawings/sketches as well.
Drawings will help in separating head from side issues; they will remove the clutter that
is unavoidably present in photographs.
I have experienced that this camera is very serviceable and does not need special tools.
I have only needed a set of precision screwdrivers and a pair of needle-pointed pliers.
4
I also recommend to use pill boxes with compartments to store the screws that you will
take out. Make a drawing of these boxes. Then also make sketches of the camera and
indicate the screws that you take out, giving them the appropriate numbering, see the
figure below.
Use drawings to highlight details and to identify screw positions and temporary storage.
5
2. The Camera
The Zorki-4 is a 35mm, coupled rangefinder camera for interchangeable lenses. It uses
the M39 Leica Thread Mount (LTM). It has a horizontal focal plane cloth shutter and
shutter speeds ranging from 1 to 1/1000 seconds and B. It has a diopter adjustment at
the viewfinder. It has no light meter and therefore does not need a battery. The first
two digits of the serial number indicate the production year.
6
The take-up spool in the camera can be removed, so if you buy a Zorki-4 through the
internet, make sure that the spool is included. You can buy a separate spool afterwards,
but they don’t come cheap and it takes some time before it will arrive through the mail.
Unfortunately, I do know what I’m talking about here.
1965 (see serial number) export - (‘made in USSR’) Zorki-4 with take-up spool.
3. History
The history of the Zorki-4 and his predecessors are closely related to those of the FED
cameras, another Former Soviet Union (FSU) line of cameras.
7
FED cameras have their origin in an orphanage in Kharkov in the Ukraine.
The First World War, the Russian Revolution in 1917 and the following civil war that
lasted till 1923 had left the country with a lot of orphaned children.
In 1926, Dzerzhinsky died of a heart attack and in 1927 the Ukrainian police opened the
F.E. Dezerzhinsky Labour Commune in his honor. The FED commune started with 150
boy and girl orphans in the age from 13 to 17 years, who spend their time doing labor
and receiving education.
The commune started making furniture and later moved to producing electric drills.
To make the Soviet Union more self-sufficient and becoming less dependent on import,
it was decided in 1932 to produce Leica camera copies. By 1934, complete copies of the
Leica II, including the lenses, were produced at the FED Commune.
When the Germans invaded the Soviet Union in 1941, the production facilities, as far as
possible, were brought to safety beyond the Urals and the rest was destroyed. After the
Second World War, in 1947, production of Zorki cameras started in the Krasnogorskii
Mekhanicheskii Zavod (KMZ) factory near Moscow. These Zorki cameras were copies of
FED cameras (that were copies of Leica cameras). The first ones had a combined
FED/Zorki engraving on the camera body.
FED returned to the Ukraine, being back in full production by 1949, and new FED and
Zorki camera designs started to divert although sharing the same origin.
8
4. Before Dismantling the Camera
The camera we have at hand here looks very good. It has no dents, scratches or missing
parts. Also, the optics are clean. The rangefinder is accurate in finding the distance.
Camera with cover taken off. The focus needs to be in the plane where the film will be.
9
Tracing paper is attached to the ‘film-plane’.
With the aperture wide open, the shutter speed on B and the shutter pressed, the image
is visible on the tracing paper and can be checked for focus.
10
By the way, the pictures above have been taken using a 1959 MIR camera. The MIR is a
‘low-budget’ version of the Zorki-4 for the internal market, lacking the low speeds
(1/60, 1/15, 1/8, ¼, ½ and 1 seconds). MIR translates from Russian to English into
peace. Zorki translates into sharp-sighted.
The reason for using the export Zorki and the MIR for showing the take-up spool and
the focusing check, respectively, is that at the writing of this report the actual Zorki-4 is
loaded with film.
Finally, before actually dismantling the Zorki-4, I need to say something about the
typical Zorki-4 smell. I have noticed that all my FSU cameras recently purchased (2
Zorki-4s, a MIR and a FED-3) come with a strong army-surplus-store smell. If you have
ever been in an army-surplus-store you will recognize this musky smell. At first, I did
not find it too offending, although a bit strong, but then I realized what it is: It is skin oil
and sweat of previous users that has been absorbed into the camera’s black covering
over the years. I definitely want to get rid of that!
To get rid of this smell, I dissolve baking soda in household vinegar and use a lint-free
cloth to rub this cleaning fluid into the covering. I repeat this until the cloth comes off
clean. Just to be sure, I give the cover a final rub with 70% denatured alcohol (the stuff
you can buy at any drugstore) and I’m done.
11
Effect of lagging shutter curtains, noticeable in the uneven exposure on the left and – to
a lesser extent – on the right of the frame. Picture taken with a FED-3 camera, having a
shutter nearly identical to the one of the Zorki-4.
So, let’s start by reassembling the camera. As a first step we will unscrew the lens.
As a first step we’ll unscrew the lens and store it in a safe place.
12
Zorki-4 without lens.
To get inside, we start by removing the shutter speed selector. For that we will loosen
the two screws, but will not remove them, see the picture below. The screw positions
are indicated by red arrows. I have used a 1.2mm screwdriver. After that we’ll loosen
the synchro ring, using a 1.2mm screwdriver as well. The ring stays in place.
Loosen (don’t remove) the screws in the shutter speed dial to get it off. One screw is on
the left, just outside view. The positions are indicated by red arrows. Also loosen (don’t
remove) the synchro ring screw (on 5 o’ clock position). The ring stays in place.
13
The top of the camera now looks like the picture shown here.
Next, we will remove the top of the winder knob, shown on the right in the figure
above. A 4mm screwdriver will do the job, see the picture below.
Bottom side of the winder knob top plate. Note the position of the star-shaped washer,
the points of the star are directed to the camera body (when in place).
Next, the winder knob itself is removed by turning it counter clockwise, see figure.
15
After removing the top of the camera we will replace the winder knob for testing
purposes. For the moment, we will lay it aside.
Next, we will remove the two screws above and below the rewind shaft, that are visible
in the above figure on the right. For that we will use a 2.4mm screwdriver.
Then, we will remove one screw from the front of the camera. That will be the crew
between the rangefinder window and the engraved ‘-4’, see the picture below. A 3mm
screwdriver will do the job. The screw to the left of the (large) viewfinder window will
be left in place. This screw gives access to a hole to stick in a screwdriver for tuning the
rangefinder.
The screw indicated with the red arrow needs to be removed from the front.
From the back, we will remove the two screws at both sides of the KMZ logo, see the
figure. For the screw on the left I have used a 3mm screwdriver. For the one on the
right, a 2.4mm screwdriver.
The screws indicated with the red arrows need to be removed from the back.
This is a good moment to stress again the importance of making drawings or at least
make notes of where the different screws are stored. The picture below shows some of
the notes I have made in the first part of disassembling the Zorki-4. On the right of the
picture is a drawing of the pill box that I have used for temporary storage of the screws.
16
My notes on screws, positions and temporary storage.
17
Zorki-4 with top removed. Note that the synchro ring is loosened but still in place.
Before we will proceed, we will first look at the construction with the flash-
synchronization-switch and the slow-speed-mechanism from different angles.
18
Top view of the flash-synchronization-switch. The red arrows indicate the screws
securing it. The circle shows a ‘missing’ screw.
19
Front view showing the flash-synchronization-switch over the slow-speed-mechanism.
We will now take out the flash-synchronization-switch by unscrewing the two screws
securing it. We use a 2.4mm screwdriver for that. Since I don’t intend to use the flash
synchronization switch, I simply lay it aside as is (i.e. I don’t move parts).
20
7. Removing, Cleaning and
Lubricating the Slow-Speed-
Mechanism
The top of the camera now looks as shown in the photograph underneath.
To take off the slow-speed-mechanism, we need to unscrew two screws, the positions
of which are indicated by red arrows. One screw (top left corner) is easily accessible. To
get access to the other one (bottom right corner), we need to rotate the gear that is
over it to expose a hole through which we can stick a screwdriver, see the earlier
shown picture (bottom page 19). To rotate this gear, we use our fingers to turn the
large gear that is around the shutter speed selection shaft counter clock wise. Once we
have access to the second screw, we unscrew it, but leave it in the slow-speed-
mechanism. Then we lift off the mechanism, carefully wriggling it around the L-shaped
hook. This L-shaped hook is indicated with the red circle in the photograph. You will
hear the mechanism unwind. Don’t panic, it’s supposed to do so.
Screw positions (red arrows) and L-shaped hook (in red circle). Turn the gear as
indicated (green arrow) to get access to the lower screw.
21
The camera with the slow-speed-mechanism taken off is shown below. Note the
different washers still present, used to level the mechanism. Some of them have been
just floating freely in grease. They have not contributed to the leveling of the
mechanism. Therefore, they will not be put back when we reassemble the camera. I
guess it must have been an off day for the factory worker. Notwithstanding that, so far,
my impression is that this is a very well-designed camera.
The slow-speed-mechanism is taken off. Note that we have turned the camera around.
Also note some washers remaining on the camera house (red arrow). Not all of the
washers are functional.
Having come this far, I think it helps to show the sketches and notes I have made during
the disassembly.
22
My notes on the disassembly of the flash-synch-switch and the slow-speed-mechanism. I
stored the washers with screw nr. 7 in the comparted pill box.
To degrease it, I have put the slow-speed mechanism in lighter fluid. A 35mm film
container is just right for this job, see the picture. Don’t leave it in overnight though
since I noticed that the plastic softens a bit. I have let it in for about half an hour.
23
After the degreasing, we let the mechanism dry and are ready for lubrication, see the
figure.
Degreased slow-speed-mechanism, ready for lubrication. Note that I have all references
mentioned in the Introduction strategically lying around.
For the lubrication, that must be done sparingly, I use sewing machine oil and a needle
to apply it, see the figure.
Lubricating, using sewing machine oil and a needle. The lid of a 35mm film container
forms a handy oil reservoir.
24
For identifying the lubrication points, I have followed the instructions found in the
thread by ‘wolves3012’ from the rangefinders-forum (see introduction). These points
are indicated in the figure below.
25
After lubrication, use the pin on the O-shaped gear (middle photograph above) to turn
this gear about three times clockwise and release it. Repeat this a few times and see
that the mechanism runs well, rewinds completely and comes to a halt at the same
place every time.
When everything is satisfactory, put the mechanism in a (zip-lock) plastic bag for
protection and lay it aside.
Store the lubricated low-speed-mechanism in a (zip-lock) plastic bag and lay aside. Drink
a lot of coffee.
26
8. Lubricating the Shutter Speed
Selector and Second Curtain Release
Arm
Next, we will remove the shutter speed selector by unscrewing the screw on top. Be
careful, since there is a spring underneath.
Remove the shutter speed selector and take care with the spring underneath the screw
(red arrow).
After lubricating the shaft, the selector can be replaced. Before we do this, we’ll first
take a good look at the different speed selector notches in the copper colored disk.
1/15 1/60
1/8 1/125
1/4
1/2 1/250
1/500
1/1000
1
B
1/30
When the shutter is fired, the first curtain starts to travel and after a while (set by the
selection of the shutter speed) it hits a trigger that releases the second shutter curtain.
This is how it works for the fast shutter speeds. In setting the lower shutter speeds,
you’ll wind the slow-speed-mechanism. You’ll wind it more if you set for a slower
shutter speed. Now, when the trigger is hit by the first curtain, the winded slow-speed-
mechanism acts as a timer and holds the release of the second shutter curtain.
The 1/30 second setting is different and closely related to B. In this setting, the first
curtain first travels the whole film exposure area distance before the second curtain is
released. This makes this setting fit for flash photography, where the actual exposure
time is not set by a moving curtain slit, but by the actual time of the flash.
The release of the second curtain is triggered by the black sliding lever indicated by the
red arrow in the figure below. For the fast speeds, this lever will be pulled inwards. For
the slow speeds it waits for the slow-speed-mechanism to push it inwards.
Black sliding lever (red arrow) triggering the release of the second curtain.
28
With the speed selector being put back in place and the winder knob being replaced
(don’t bother about the top plate), we can cock the shutter, select a speed and fire.
When we do so, the second curtain will be stuck. Upon pushing the black lever with a
screwdriver, we can release the second curtain.
The actual release of the second curtain is performed by the second curtain release
arm. The top of that device we see in the picture above, just below the black sliding
lever that was indicated by the red arrow.
To remove this arm, in order to clean and lubricate it, we will first need to unhook the
spring, see picture below (green arrow).
Spring, holding the second curtain release arm indicated with the green arrow. The red
arrow indicates where the spring is connected to the body.
I found the unhooking of the spring quite cumbersome and decided for removing the
spring altogether, loosening the screw indicated with the red arrow. A 3mm
screwdriver was fit for this job, see the pictures below.
29
Remove the retaining spring by unscrewing it (left, middle). After that the second
curtain release arm can be lifted out (right).
Finally, we will clean the arm, lubricate it with thin oil and place it back. After that we’ll
replace the retaining spring.
Clean and lubricate the second curtain release arm with thin oil before replacing it.
30
Next, we will lubricate the shaft of the speed selector itself and finally replace the
speed selector. While lubricating the shaft, also some oil needs to be applied,
sparingly, underneath the selector top plate.
Most of the references I have used, advice at this point to clean the optics of the
viewfinder and rangefinder. I choose to postpone this to a later moment. There is more
cleaning and lubricating to do and most probably I’ll be touching the glass parts with
my greasy fingers. I choose to do the cleaning of the optics at the moment of
reassembly.
We can now take out the shutter-rewind collar, shutter button, spring and shutter rod,
see picture below.
Shutter-rewind collar, shutter button, spring and shutter rod taken out. By removing the
screw (red arrow) a second collar can be taken out.
32
A second collar can be taken out by loosening the screw indicated in the picture above
(red arrow).
At this point I want to show my notes again. I want to stress the importance of making
notes and drawings/sketches, next to taking photographs, during the whole
disassembly process. I understand that this is a practice that has been used by watch
repair technicians in the pre-digital photography era. I think that this practice has lost
nothing of its importance, despite modern digital photography.
My notes on the disassembly of the shutter speed selector, second curtain release arm
and shutter-rewind mechanism.
33
The picture below also indicates the screw to be loosened to take out the second collar
(red arrow). Be careful, a second spring is underneath! A 1.2mm screwdriver will do the
job.
Disassembled shutter-rewind mechanism. Note that the screws are loosened, not
removed.
34
One additional collar with spring has come out. A second one did not come out, but this
is not considered to be a big deal.
Next, we will degrease the inside, using q tips soaked in lighter fluid, see the picture
below. This cleaning will also take care of the collar left behind.
Lubricating the shutter-rewind mechanism parts with silicone grease before reassembly.
In the reassembly take care that the parts are reassembled in the same position that
they were taken out. The shutter release rod needs to be installed with the narrowed
part at the top, for example.
Make sure that the shutter-rewind mechanism works properly after reassembly. When
the collar is turned counter clockwise, the film transport engages. When the collar is
turned clockwise, the film transport is disengaged. This can be checked by inspecting
the bottom of the film sprocket, see pictures below.
Left: sprocket engaged. Right sprocket disengaged. Notice the distance from the black
wheel.
36
10. Removing the Shutter Crate from
the Body
As a final sub-project, the shutter crate needs to be removed from the body.
That will give access to the bottom bearings of the shutter spring rollers and to the
restrictor gear. Then, cleaning and lubrication will become easy. We expect to find lint
and film debris at this bottom position that needs to be removed. The top bearings of
the shutter spring rollers will be lubricated – if at all - without gaining a special access.
We will start by removing the three screws from the top plate in the back, see the
figure below. We will use a 1.8mm screwdriver.
Removing the three top plate screws on the back of the Zorki-4.
Next, we will remove the two screws from the top plate on the front, see the figure
below. Note that in this picture, the screw on the left side is a long one and the one the
right side is a short one. We will remove both screws, using a 1.8mm screwdriver.
37
long short
Removing the two top plate screws on the front of the Zorki-4.
Next, we will remove the self-timer lever using a 3mm screwdriver, see the figure
below.
When this is accomplished, we will take out the lens mount by removing the four
screws, using a 1.8mm screwdriver. See the figure below.
When the four screws are out, we carefully lift out the lens mount, taking care not to
lose or mess up the paper shims underneath, see the next figure.
39
Shims underneath the lens mouth.
To prevent anything happening with the order of the shims it is best to mark the
positions. Also mark the lens mount top position, while you are at it. This assures that
we can reassemble the mount exactly as we have taken it out.
Marking the shims positions and the top of the lens mount itself.
40
Finally, we will remove the last two screws on the front of the housing, using a 1.8mm
screwdriver.
Now, we can take the shutter crate out of the body. We have to wriggle the body,
applying force on the bottom part, to make it slip out from underneath the top plate,
see the figure below.
Wriggle the bottom of the body (1) to slip the top plate off (2).
41
This may need some force and time. It may well be the first time in half a century that
these parts are coming apart. The result is shown below.
Before we will dive further into the shutter crate, we will first have a closer look at the
exterior.
If we look closely at the base for the lens mount, we see the remains of a light seal that
has been damaged in the separation of the shutter create and the body.
Remnants of a light seal on the lower part of the lens mount base.
42
Obviously, this light seal was glued all around the lens mount base. The top part is
undisturbed, as can be seen in the above picture. Upon reassembly, we will remove the
seal and glue remnants from the lower part. Then we will glue a string of black wool
thread around the lower part of the base to replace the damaged seal.
long
short
short
long
Shutter crate, showing the restrictor gears in the blue rectangle. The light baffles inside
the crate (red rectangles) are held in place with the screws inside the red circles. The
crate front is secured by the (long and short) screws indicated by the green arrows.
We will start by removing the light baffle screws. The light baffles will fall into the crate
from which we will retrieve them after removing the front of the crate. The light baffles
43
need to be loosened first. Otherwise it will not be possible to remove the front of the
shutter crate.
For both the light baffle and the crate front screws we will use a 2.4mm screwdriver.
Note that the front of the shutter cate is secured by two types of screw, see the above
figure. The ones on the lower left and upper right corner have a shiny head and are
shorter than the other two that do not have a shiny head.
Before showing the opened-up shutter crate, this is a good moment again to give an
update on the sketches and notes I have taken during disassembly.
My notes on the separation of the shutter crate and the body and the removal of the
light baffles and front plate from the shutter crate.
44
Finally, the opened-up shutter crate is shown in the picture below.
Opened-up shutter crate with above the two light baffles and above that the crate
front.
In my despair I googled the web and through ebay ordered a MIR (Zorki-4 without the
low speeds) that had been CLA’d by the vendor. Having thus secured a plan B, I set
myself to the task of cleaning and lubricating the shutter and film transport mechanism,
to be followed by reassembling the Zorki-4. Fortunately, this reassembly – although not
without challenges - turned out to be less daunting than I had anticipated.
45
13. Cleaning and Lubricating the
Shutter and Film transport
Mechanism
The first thing to do is cleaning the restrictor gears, see the picture below. I was
expecting having to take out a lot of lint and film debris, but found nothing of the sort.
The restrictor gears are indicated by the red arrows. Pieces of film may end up here.
In fact, I found the camera to be very clean. I was only amazed by the amount of short
hairs I found during cleaning and lubrication. I guess this may be due to the earlier
mentioned supposed off day of the technician assembling the camera, paired to a less
than perfect quality control system. My general impression of the camera is that it is a
very well thought over design, made of robust elements, meant to last and having
maintenance in mind. The only flaw seems to be the lubricants used that tend to
harden over time. But who would have thought that these cameras would still be used
sixty years after production?
46
We will lubricate the gears shown in the picture above. By cocking and firing the
shutter repeatably we can make the gears turn. That is why we replaced the winding
knob earlier. With this process we will get access to all sides of the gears for lubrication.
For the lubrication we will be using a silicon grease.
Next, we will lubricate the spring roller with thin (sewing machine) oil. The spring roller
is located on the right of the shutter crate, see the figure.
Lubricate the spring roller sparingly on the indicated position (red arrow).
47
Then, we will oil the shutter drum shaft, taking care that we do not soil the shutter
curtain. The point to apply the (thin) oil is shown in the pictures below.
Lubrication of the shutter drum shaft. The red arrow in the left picture shows the tiny
access for applying oil. The red circle in the right picture shows how oil is very carefully
applied, using a needle.
Finally, we will oil the bottom drum shaft pivot. Therefore, we will have to remove the
bottom cover, see the next set of pictures. Both screws in the bottom cover can be
removed by using a 2.4mm screwdriver. Note that shims are present under the cover. A
black one is used (in my camera) for the screw shown on the left, a brass one for the
screw on the right. The shim lengths are not identical, so note which shim belongs to
which screw.
48
The bottom cover is held in place by two screws. Underneath, differently sized shims are
being used. Note which one belongs to which screw.
Removing the bottom cover. Notice the brass shim on the right and the black shim (in
tweezers) on the left (red arrows).
49
We will remove the silver-colored shutter latch. Before doing so, note the position. The
two screws you can see on the right in the above pictures are for the adjustment of the
shutter curtain tension. We will get to that in the end.
The shutter latch can be removed using a 2.4mm screwdriver. When the latch is
removed, we will oil the pivot, using sewing machine oil, sparingly applied with a
needle, see the pictures below.
Shutter latch removal and oiling of the bottom drum shaft pivot.
50
The picture below shows the notes I have taken on this part of the disassembly process.
Note that the position of the shutter latch has been sketched.
Well, this is as far as we will go in dismantling the Zorki-4. We will not dismantle the
shutter crate and take out the shutter curtains. There is no reason for it and to quote T.
Bert Lance (Director of the Office of Management and Budget in Jimmy Carter’s 1977
administration) “If it ain’t broke, don’t fix it”.
Now we will have to reassemble the camera. In the process we should not forget to
apply a new light seal around the lower part of the lens mount base.
Reassembly is basically disassembly in reversed order, but some steps will need some
extra attention. Especially the reassembly of the slow-speed-mechanism is a bit tricky.
We will show the whole reassembly process in pictures.
After reassembly we will need to adjust the shutter curtain tension.
51
14. Reassembly
As said, we will now repeat the whole procedure, but in the reverse order. Some pictures
that we will use will look familiar. That is because I did not take enough pictures during
the disassembly and ‘borrowed’ the pictures taken during reassembly.
We will start easy and will replace the shutter latch to the original position. After that we
will replace the bottom cover, where the two shims will be replaced in their original
positions (the black one on the left, the brass one on the right), see the pictures below.
All screws can be fastened with a 2.4mm screwdriver. We will tighten the latch really
well.
Replace the shutter latch in the original position and tighten well, replace the shims and
then replace the bottom cover.
Next, we will replace the front of the shutter cave. Do not make the mistake I made
which is forgetting to first put the light baffles into the shutter crate. Once the front is in
place, you cannot place the light baffles inside through the lens opening.
52
Replacing the light baffles. Don’t worry too much about the exact placement.
Once the light baffles are more or less into position, we can replace the front of the
shutter crate.
Next, we will secure the front with the long and short screws on the outer rim of the
front. We will use a 2.4mm screwdriver for this.
The fastening of the light baffles is not very straightforward, unfortunately. Using your
fingers to align the screw holes with the screws does not work. Using a cocktail pick
instead of the screw also does not work. What does work, fortunately, is using a pair of
tweezers to hold the rim of the light baffle and guide it to the correct position to fasten
the screw, see the figure below.
54
Using a pair of tweezers to align the light baffle for securing the screw.
We will fasten the screw very loosely and when we have all four screws inserted in this
way, we will tighten them all (2.4mm screwdriver).
With the shutter crate front and light baffles being reassembled, we will need to replace
the light seal around the lower part of the lens mount base.
55
For that we will first need to remove the remnants of the old seal and glue. Q tips and
70% denatured alcohol and/or lighter fluid and patience will do the job.
Don’t forget to clean the remnants from the body part as well.
Also clean the seal and glue remnants from the body.
56
The cleaned lens mount base is shown in the picture below.
Next, we will prepare a black wool thread for being used as a light seal. This preparation
consists of applying a dot of (any) household glue to the tip to prevent it from fraying.
57
While the wool is drying, we will apply glue to the rim of the lens mount base. My
preferred glue for this (and other) applications is Bison Tix (also because it is developed
and manufactured in the town where I was born and raised). When applied to a single
surface, the two glued parts can be taken apart relatively easy after drying. When
applied to both surfaces, the connection is extremely strong.
Next, we will take the black wool thread and press the glued tip at the beginning of the
light seal trajectory. While holding it, we will apply some pressure and twist the thread to
the desired thickness before pressing it into the glue. See the picture below.
Shutter crate with new light seal pushed back into the body.
Then, with a 1.8mm screwdriver, we will secure the shutter crate with two screws.
Next, we should refit the lens mount, but a close inspection revealed that the shims were
rather loose.
59
The loose shims (red arrows) need some attention.
If we turn the lens mount around to attach it to the body, we might mess up the order
and placement of the shims. Therefore, we have decided to apply some glue first. After
the shims have dried, we will turn the lens mount around and put it on the body. Note
the mark for the top of the mount.
Attaching glue to keep the shims in place. The red arrow indicates the mark for the top of
the lens mount.
We will attach the screws, using a 1.8mm screwdriver. A pair of tweezers may be handy
in attaching the screws.
60
Using a pair of tweezers may aid in attaching the lens mount screws.
Next, we will re-attach the self-timer lever by pushing in the lever with light seal in the
hole on the left and securing the screw using a 3mm screwdriver. When that is done, we
will secure the top plate to the body with the two front screws (the long one on the left
and the short one on the right), using a 1.8mm screwdriver. This is shown in the two
pictures below.
These pictures also clearly demonstrate why we have postponed the cleaning of the
optical parts, i.e. the rangefinder (left) and the viewfinder (right). It is unavoidable in the
assembly and reassembly process thus far to touch the glass with greasy fingers. We will
do the cleaning just before we close the top of the camera.
61
Reattaching the self-timer lever.
Securing the top plate to the body. Use the long screw (green circle) on the left and the
short screw (red circle) on the right.
Then, we will turn the camera around and secure the top plate to the body on the back
with three screws, using a 1.8mm screwdriver.
62
We have now reached the most-tricky part of the reassembly, that is the reattachment
of the slow-speed-mechanism.
The above picture shows the notes and sketches that I have made during the Zorki-4
disassembly. Now, in the reassembly process they prove to be of great value. I dare to
say that they are more informative and easier accessible than the pictures taken. In the
end you will need both.
63
15. Reassembly of the Slow-Speed-
Mechanism
The most-tricky part in the whole reassembly process is the reattachment of the slow-
speed-mechanism. We will have to make sure that the (timer) mechanism interacts well
with the rest of the shutter mechanism in releasing the second shutter curtain.
Therefore, the comma-shaped latch at the underside of the slow-speed-mechanism, see
figure below, must activate the black metal lever on the camera body, see figure below,
at exactly the right moment.
The comma-shaped latch must activate the black metal lever (red circle and arrow) and
the pin on the o-shaped gear should touch the shutter speed selection pin on the
indicated position (green circle and arrow).
64
The best way to do this, is as follows:
1. Make a scratch on the top surface of the o-shaped gear to indicate the position of
the pin, see the picture.
Gently scratch the top of the o-shaped gear to indicate the position of the pin
underneath.
2. Cock the shutter (turn the winding knob) and set the shutter speed to 1/125
seconds. That is, lift the selector and make sure that you’ll land the pin in the last
notch before the slow speed selection notches. These latter notches are shallower
than the standard ones. See the figure below.
After cocking the shutter: Lift the shutter speed selector, turn it and let the speed
selection pin land in the 1/125 sec notch.
65
3. Cock the shutter halfway, i.e. turn the winding knob until the L-shaped hook is at
the top of the brass, notched, shutter speed selector plate (12 o’ clock position).
4. Wind the slow-speed-mechanism by turning the o-shaped gear two turns (look at
the tensioning of the spring to determine the right direction), see the picture
below.
Turn the o-shaped gear two turns and watch the tension on the spring (red arrow)
increase to determine the correct turning direction.
5. Keep hold of the o-shaped gear and replace the shims on the body where the
slow-speed-mechanism will land. Now keep holding the o-shaped gear and place
the slow-speed-mechanism over the speed selector, wiggling around the L-shaped
hook. Keep hold of the o-shaped gear and complete the cocking of the shutter. The
L-shaped hook is now positioned to the left.
The setup should now look like this. Contrary to this picture you should keep hold of the o-
shaped gear.
66
6. The pin underneath (look at the scratch mark) should be positioned just before
(above in the previous picture) the speed selector pin. The comma-shaped latch is
just about to activate the black metal lever.
7. Now, while still holding the gear, replace the two screws, using a 2.4mm
screwdriver. You will have to make slight rotation corrections to the o-shaped gear
so that the hole in the smaller gear will give access to the screwdriver. Now you
can release the tension on the slow-speed-mechanism. The mechanism should
unwind for a small amount only. Check that the mechanism is level with the
camera body.
67
8. Gently, check for the different shutter speeds. If you feel resistance, stop. In that
case, or if the shutter speed is not correct, dismantle the slow-speed-mechanism
and start all over again. Don’t despair. I had to go through the procedure six or
seven times before it was correct.
The first shutter curtain is not completely moved to the correct position.
Since everything is cleaned and lubricated, this effect must be due to a lack of tension.
68
To adjust the curtain-tension we will have to remove the bottom cover of the shutter
crate again. Fortunately, we don’t have to remove the shutter crate from the body for
this, see the next figure.
Camera in upside-down position in a makeshift hold. The bottom cover of the shutter
crate needs to be removed. Use a 2.4mm screwdriver and note the positions of the shims.
Since we will need to adjust the curtain tension from the bottom of the camera, I have
made a support for holding the camera in an upside-down position. This support consists
of a block of Styrofoam with a wide slit cut out to hold the camera. To prevent the
Styrofoam from shedding particles, I have covered the whole block in aluminum tape.
There is no special reason to use aluminum tape, it was just what I was having at hand.
The setup then looks like shown in the figure.
Once the bottom cover is removed, we will get access to the shutter curtain tension
screws for both curtains, see the next figure.
Second curtain (top) and first curtain (bottom) tension adjustments screws.
69
To adjust (increase) the tension of the first shutter curtain, we will first remove the small
stopper. The we will loosen the screw in the center of the adjustment screw while
holding this adjustment screw with a pair of pliers. Then we will turn the adjustment
screw counter clockwise to increase the tension. We will do this for quarter or half turns,
securing the center screw every time, until we see that for a released shutter the curtain
end has moved to the correct position. Then we will tighten the center screw and refit
the stopper, see the figure.
Adjusting the curtain tension. Shown here is an adjustment of the second curtain tension.
In the picture above, actually the second curtain tension is being adjusted. This was done
at a later stage, but I forgot to take pictures of adjusting the first shutter curtain tension.
However, the procedure is identical, so the picture is still relevant. My notes on the
shutter curtain tension adjustment are shown in the next figure.
70
Notes on adjusting the shutter curtain tension.
With the shutter curtain tension adjusted, we can now move to cleaning the optics of the
rangefinder and the optics of the viewfinder.
Before doing that, we will first replace the flash synch switch. We will place the device
over the shutter speed adjustment shaft and secure it with the two screws. We will use a
2.4mm screwdriver for that and place the screws in the upper-left and lower-right
corners only, see the figure.
71
Securing the flash synch switch with the screws on the designated positions.
Viewfinder in the green rectangle and (coupled) rangefinder in the red rectangle.
72
Front view of the camera without top. On the left the rangefinder and on the right the
viewfinder. A rangefinder calibration screw is visible in the red circle. In the green circle
we see a diopter adjustment lever for the viewfinder
In between the rangefinder and the viewfinder, we will see the coupling mechanism. The
rangefinder can be calibrated by turning the screw shown in the red circle in the picture
above. When the top of the camera is on, this calibration screw is accessible through
removing the screw in the lower left corner of the viewfinder glass, see the figure.
Remove the screw in the red circle to get access to the rangefinder calibration screw.
73
We can get further access to the viewfinder by taking out the screws on the viewfinder
window, see the next figure.
We will blow the dust away and avoid touching any mirroring or colored surface. The
other glass surfaces we will clean using q tips with 70% denatured alcohol. Since the
mirrors are made of silver deposited on the glass, rubbing or even touching them may
result in irrecoverable damage. For the same reason we do not touch the colored spots
of the rangefinder optics.
When all other glass is cleaned, we will replace the viewfinder window and will be ready
for putting the top back on.
74
and start securing it by securing the two screws above and below the winding shaft, see
the figure. We will use a 2.4mm screwdriver for that.
Securing the two screws above and below the rewind shaft.
Next, we will add the rewind knob again, securing it by turning it clockwise.
Securing the rewind knob by turning it clockwise and securing the shutter speed
indication ring (see red arrow).
75
While we are at it we will also secure the screw of the shutter speed indication ring. We
will use a 1.2mm screwdriver for that.
Then we will secure the two screws on the back, using a 3mm screwdriver for the one on
the left and a 2.4mm screwdriver for the one on the right. These two screws – at least for
this copy of the Zorki-4 – are not identical.
Next, we will secure the screw on the front, using a 3mm screwdriver and reattach the
winder knob top plate, using a 4mm screwdiver.
Securing the last screw. Note that the screw next to the viewfinder window is an access
for the rangefinder calibration.
76
Then, we will give the camera a final polish, reattach the lens and ‘Bob is your uncle’.
Reassembled camera. Don’t forget to take off the cleaning cloth lint from the rewind
knob.
77
The idea is that we will create a lightproof volume. On one side we will place the opened
Zorki-4 camera. We will place a sheet of tracing paper on the focal plane. On the other
side we will place a digital camera with a macro lens that is focused on the tracing paper.
We will cock the shutter of the Zorki-4 and select a shutter time. Then we will select the
Bulb setting on the digital camera (with the appropriate aperture setting and ISO value,
this might need some trial and error). We will activate the shutter of the digital camera
(press the shutter button and keep it pressed), that is we will open the shutter. Nothing
will happen since the shutter of the Zoki-4 is closed.
Then we will fire the shutter of the Zorki-4 and after that we will close the shutter of the
digital camera (release the shutter button). Using a cable release for the Zorki-4 might
ease the handling of both cameras.
Through examining the image captured by the digital camera we can see if both shutter
curtains travel as expected. If one of the curtains is traveling too fast or to slow, we will
see that in the image. Through altering the tension of the curtain(s) involved we can
correct for that. Once we are happy wit the results, the camera is set for having a roll of
film run through.
To make such a setup we will start by making a rig to hold the Zorki-4 camera at one end
and provide a means to fasten the digital camera on the other end. For that we will be
using a macro-slider and some metal strips, see the picture.
We will make it tight enough so that we can squeeze in the Zorki-4 without its cover.
Next, we will place a piece of tracing paper on the focal plane of the Zorki-4 and add the
digital camera, securing it on the tripod screw. Here we are using a Nikon D7200 with
79
Nikkor 40mm macro (micro in Nikon terminology) lens. We also have attached a
(standard) cable release to the shutter of the Zorki-4.
Zorki-4 and Nikon D7200 with Nikkor 40mm macro lens attached to the rig.
80
The rig shown from another angle. Note the small cushions made to position and tighten
the Zorki-4.
Next, we will create the darkened environment. We will do that in two steps. The first
step involves the use of black paper and is shown in the next figure.
First step in creating the lightproof volume: adding a paper tunnel between the Zorki-4
focal plane and the take-up lens of the digital camera.
81
Next, we will wrap this setup in black cloth to make it really lightproof. We will take long-
time bulb shots (a few seconds) with the digital camera, not using the Zorki-4 at all, to
test for light leaks. When the image taken is completely black, we are good.
Next, we will take pictures for different shutter speeds, inspect the digital images and – if
necessary – adjust the curtain tensions. Be warned, this is a tedious process. For a large
part, this is due to the shabby testing rig. For this camera it sufficed and we only had to
adjust the second curtain once.
If the construction will be further developed it might also be possible to use the digital
camera to check for actual shutter speeds. One way might be to start shooting at
different digital speeds with the Zorki-4 in Bulb mode. Then shoot the same scene at one
speed with the Zorki-4 with the digital camera in Bulb mode. Finally compare the
histograms and see which digital speed most closely matches the Zorki-4 speed. Repeat
this for all speeds.
82
Image taken with the Zorki-4 and Nikon D7200 test setup (the image is upside down and
left-right reversed of course).
The results are – technically – good. The shutter shows no lag or capping. The exposures
are consistent with the applied ‘sunny 16 rule’. Changing the shutter speed in
accordance with a changing aperture value does not change the exposure.
83
Zorki-4 test shots on Kodak Gold 200 after CLA.
84
21. Conclusion
This project, even if I haven’t done anything fancy like replacing the shutter curtains, has
been the most involved camera dismantling and reassembly I have ever performed so
far. Looking back, I think that the Zorki-4 camera is the best camera for beginners to
learn camera CLA and repair. The camera does not need special tools and I have not
encountered nasty or fragile clips. A set of standard precision screwdrivers, a pair of
needle-tipped pliers and maybe a pair of tweezers will do the job.
Before starting on this project, I have searched the web on information and encountered
many horror stories about shutter curtains glued in askew, light leaking through the self-
timer and broken pieces. I have even read the advice not to touch a good looking Zorki-4,
since most probably it was laid aside because it did not work.
It may have been the particular Zorki-4 at hand, but this copy looks good and it only
suffered from gummed up grease. I did find some washers where they weren’t supposed
to be and I found a lot of hair, but in general my impression is that of a well-assembled
camera.
It is well known that for this type of camera you need to cock the shutter before you set
the shutter speed. If you don’t you will get wrong shutter speeds, but the warning that
you might snap off the speed selector pin seems a bit over-dramatic to me. Excessive
force is needed to do that and if you handle the device like a precision mechanical tool,
which it is, I find it hard to believe that you can brake off the pin by accident.
All in all, I have learned to love this camera. The design is clever and well thought of,
although based on copying. The parts are well made and made to fit and last and the
camera is extremely maintenance friendly. As a bonus it delivered me a functioning MIR
as well. I have also obtained an export Zorki-4 needing CLA. Now I know I can do it.
I think that the Zorki-4 really offers 90% of the Leica experience for 10% of the price. It is
absolutely worth investing time and effort to give it a CLA.
85