PDS STRATA EPOXY MT 45520 en-GB PDF
PDS STRATA EPOXY MT 45520 en-GB PDF
Strata Epoxy MT
Mix: 45520. Base: 45529. Curing Agent: 95521.
Description: Strata Epoxy MT is a two-component solvent-borne epoxy paint for use in areas of medium
traffic.
Recommended use: Designed to protect concrete floors and walls in areas exposed to medium traffic such as car
parks, warehouses, factories and sports stadiums. Ideal to medium duty floors were protection
to spillages and medium abrasion is specified.
Availability: Available in 5L, 10L. (Packing may vary from country to country depending on local requirements).
Physical constants*:
Colours/shade Nos.: According to Strata Colour Card and RAL K7 colour card.
Finish: Glossy
Volume solids, %: 80 ± 2%
Theoretical spreading rate: 8.0 m²/litre/coat 100 microns DFT**
Flash point: >29°C
Specific gravity: 1.54 kg/litre
Dry to touch: 7 hours at 10°C 31/2 hours at 20°C 11/2 hours at 40°C
Initial hardness: 24 hours at 20°C
Fully cured: 7 days before the floor can be exposed to medium duty traffic
VOC content: 199 g/litre
*The physical constants stated are nominal data according to the Hempel Group's approved formulas.
They are subject to normal manufacturing tolerances and where stated, being standard deviation
according to ISO 3534-1.
**The theoretical spreading rate has been calculated for the stated volume solids and dry film thickness. A
practical spreading rate will depend on the actual dry film thickness, the nature of the substrate and
relevant consumption factor. The physical constants are subject to normal manufacturing tolerances.
Further references can be found in the "Explanatory Notes".
Application details:
Mixing ratio: 77:23 on volume
Application method: Brush, short haired roller
Thinner (max.vol.): Do not dilute
Pot life: 70 minutes at 20°C Reduced at higher temperature
Cleaning of tools: Hempel Tool Cleaner 99610
Indicated film thickness, dry: 2 x 100 microns
Indicated film thickness, wet: 2 x 125 microns
Overcoat interval, min: 48 hours at 10°C 24 hours at 20°C 12 hours at 40°C
Overcoat interval, max: 6 days at 10°C 72 hours at 20°C 36 hours at 40°C
Safety: Handle with care before and during usage. Read all labels on packaging and paint containers
before usage, consult Hempel for any inquiries. Material Safety Data Sheets follows all local
and national safety regulation. Avoid inhalation; avoid contact with eyes and skin. Do not
swallow. Take precautions against possible risks of fire or explosion. Apply only in well-
ventilated areas. Remember to protect the environment.
Application conditions: Application can only proceed at temperatures above 10ºC, relative humidity below 75%. Other
sealer/filler types may be specified. Drying data are given on the assumption that proper
ventilation is provided. Strata Epoxy MT should not be applied to concrete with more than 4%
moisture.
Surface preparation: The surface should be stable, firm, dry and free from dust, sand, loose old paint, laitance, dirt,
grease and oil. Proper surface preparation is a must, mechanical surface preparation is highly
recommended (see Strata Surface preparation brochure or consult our technical
representatives).
Sealing/Priming: Strata Epoxy MT can be used as a self-priming material on smooth, solid, non-pourous
substrates. For pourous substrates we recommend to use Strata Primer SF or Strata Sealer.
Filling: Strata Epoxy Floor Filler. Recommendation: apply primer/sealer prior to the application of a
specified filler.
Mixing: Strata Epoxy MT is a two-component material (base and curing agent), which must be mixed
together prior to use. Stir the base continuously while adding the contents of the curing agent.
Mix until the mixture is homogeneous.
Application: Apply the mixed product to the surface with a good quality of short haired roller or brush. Let it
dry for 24 hours before applying the second coat with the same tools used for the first coat.
The second coat should be applied at a right angle to the first coat.
Storage & handling: Product must be stored as per local regulation. Keep in dry and ventilated location, far from
heat and direct sunlight.
Remarks: Epoxy coatings will yellow, chalk and lose gloss over a period of time when exposed to direct
or diffused sunlight. Yellowing is a surface phenomenon attributed to the chemical nature of
the resin with natural darkening. Degree of yellowing can vary from product to product but is
generally more obvious in pale shades. This has no influence on the function and performance
of the coating. For UV protection, we suggest you to apply a top coat of Strata PU Top or
consult Hempel for more suitable options.
For explanations, definitions and scope, see “Explanatory Notes” available on hempel.com. Data, specifications, directions and
recommendations given in this data sheet represent only test results or experience obtained under controlled or specially
defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions of any intended use of the
Products herein must be determined exclusively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to Hempel's general conditions of sales, delivery and
service, unless otherwise expressly agreed in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all
claims involving, any liability, including but not limited to negligence, except as expressed in said general conditio ns for all
results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the
overleaf or otherwise. Product data are subject to change without notice and become void five years from the date of issue.