Catalog: Dual Plate Wafer Check Valve

DUAL PLATE WAFER CHECK VALVE
CATALOG
www.walworth.com
INDEX
INTRODUCTION
ENGINEERING CONTROL........................................................................................................................................ 5
QUALITY SYSTEM...................................................................................................................................................... 5
QUALITY CONTROL EQUIPMENT.......................................................................................................................... 9
VALVES
WAFER TYPE VALVES DOUBLE DISC.................................................................................................................11
WAFER LUG TYPE VALVES DOUBLE DISC....................................................................................................... 12
MOST COMMON MATERIAL OF THE BODY...................................................................................................... 13
MOST COMMON TRIMS.......................................................................................................................................... 13
CHEMICAL COMPOSITION OF MOST COMMON MATERIALS...................................................................... 14
OPERATING TEMPERATURE FOR SOFT SEATS............................................................................................. 14
DESIGN FEATURES................................................................................................................................................. 15
DUAL PLATE WAFER CHECK VALVE CLASS 150........................................................................................... 16
DUAL PLATE WAFER CHECK VALVE CLASS 1500......................................................................................... 24
DUAL PLATE WAFER CHECK VALVE CLASS 2500......................................................................................... 26
TECHNICAL INFORMATION................................................................................................................................... 28
PRESSURE-TEMPERATURE RATINGS............................................................................................................... 31
PRESSURE DROP OR FORCE LOSS.................................................................................................................. 34
DROP PRESSURE OR FORCE LOSS GRAPHIC............................................................................................... 35
DESIGN BASIS.......................................................................................................................................................... 36
HOW TO ORDER....................................................................................................................................................... 37
TERMS AND CONDITIONS..................................................................................................................................... 38
594-0007
www.walworth.com 3
WALWORTH
WALWORTH is one of the world´s most comprehensive industrial
valve manufacturers. Founded in 19th century by James Walworth, the
Company has consistently dedicated itself to improvements in design and
manufacturing of an array of valves exceptionally suited for the world´s
fluid control sector. We satisfy all end use industries and comprehensive
customer requirements by adhering to the most demanding quality
standards.
WALWORTH relies on its broad experience in supplying valves to the

petrochemical, oil & gas, petroleum, power generation, pulp and paper,
cryogenic and geothermal industries, among others.
Over the years, Walworth has produced over 40,000 different types of
products and serves as a global supplier to various markets utilizing the
expertise of over 500 trained employees.
Our manufacturing system includes: utilization of Company directed

raw material warehouses; modern and newly acquired specialized
machinery; welding processes such as SMAW, GMAW, SAW, PAW;
assembly testing for all low pressure, high pressure, and at low or
high temperatures; painting and coating processes; export crating and
shipment.
WALWORTH is capable of providing the world´s most comprehensive

industrial valve line to the North American, Central American, South
American, European and African markets. WALWORTH is proud to meet
and satisfy the precise demands of our customers throughout the world
by providing a quality product, competitive cost, and excellent service.
WALWORTH VALUES
MISSION VISION
WALWORTH manufactures and supplies world-class To be the world leader of unparalleled valve manufacturing
valves and components for the flow control industry through and supply, WALWORTH:
exceptional service, competitive pricing, and consistently,
on-time deliveries. • Set the standard for product quality in the flow control
industry.
• Exceed the service expectations of our customers.
• Forge enduring relationships with customers, team
members, and community.
• Hire, develop, and retain experienced and dedicated
team members.
4 www.walworth.com
WALWORTH ENGINEERING CONTROL
WALWORTH products are manufactured following the strict
international standards recognized all over the world, such as
API, ANSI, ASME, ASTM, MSS, NACE, AWWA, BSI, CSA,
among others. Our Engineering team consistently monitors
updates to these standards and incorporates any applicable
changes that affect the design, regulations and/or performance
of our products.
Our designs are made using the most advanced technology

and equipment, finite elements, and CAD system programs to
ensure proper assembly and performance. From conception to
calculation to detailed drawings for manufacturers, WALWORTH
is a leader in development of new products that meet the needs of
the current valve market.”
WALWORTH QUALITY SYSTEM

Throughout the years, WALWORTH has developed its Quality System which is an integral part of our manufacturing policy. Our
primary goal is to provide products that meet and exceed market standards. In this sense, WALWORTH is an ISO-9001 Audited
and Certified Company that has achieved major certifications worldwide. Our system includes the selection of raw materials from
approved vendors, and rigorous oversight of our manufacturing process that is vital to quality control. The use of serial numbers
allows WALWORTH the ability to not only ensure the quality of components used but to monitor and trace the fabrication process as
well.
Certificate API-6D No. 6D-0097 Certificate API-6A No. 6A-0234

Issued by American Petroleum Institute to apply on Gate valves, Plug From American Petroleum Institute to apply on valves at PSI, 1
valves, Ball valves and Check valves manufactured in accordance through 4.
with API-6D specification.
www.walworth.com 5
Certificate API-594 No. 594-0007
Issued by American Petroleum
Institute to apply on Check Valves-Type A; Check Valves Type
B manufactured in accordance with API-594 specification.
Certificate ISO-9001 No. 0038

Issued by American Petroleum Institute since April 1999.
API-600 Certificate No. 600-0109

Issued by American Petroleum Institute to apply on Bolted
Bonnet Steel Gate Valves manufactured in accordance with
API-600 specification.
API-602 Certificate No. 602-0024

Issued by American Petroleum Institute to apply on Compact Certificate as per PED 97/23/EC Module H
Steel Gate Valves, Compact Steel Globe Valves, and To stamp CE products.
Compact Steel Check Valves manufactured in accordance
with API-602 specification.
6 www.walworth.com
Supplier Qualification Certificate NO. 279/13 Certificate NMX-CC-9001 (Mexican Standards ISO-9001) No.
Issued by the Equipment and Materials Testing Laboratory, CFE 0552/2007 Issued by PEMEX in accordance with ISO-9001 Quality
(LAPEM in Spanish) Assurance System.
PRODUCT CERTIFICATIONS
Emissions after 500 cycles at ambient and 350 °F Emissions after 500 cycles at ambient and 350 °F
Issued by Yarmouth Research and Technology Lab for 3 inch Class Issued by Yarmouth Research and Technology Lab for 8 inch Class
300 Gate Valve After 500 cycles the measurement result was less 300 Gate Valve After 500 cycles the measurement result was less
than 50 ppm. than 50 ppm.
Emissions after 500 cycles at ambient and 350 °F

Issued by Yarmouth Research and Technology Lab for 16 inch Class
150 Gate Valve After 500 cycles the measurement result was less
than 50 ppm.
www.walworth.com 7
Certificates of Ultra Low Fugitive Emissions No. 20985-3, 8 & TÜV Rheinland Certificate No. TRASA 700-13-0019
16 in accordance with ISO-15848-1 “Industrial Valves” API-6D Trunnion mounted bolted body ball valves, carbon steel (A105-
Measurement, Test and Qualification Procedures for Fugitive WCB) construction, double block and bleed service, primarily used
Emissions “Part 1: Classification System and Qualification but not limited to the oil and gas standard and severe applications.
Procedures for Type Testing of Valves”.
Fire Test Certificate No. 01-1/05 TA Luft Certificate (Fugitive Emission) Approval
In accordance with API-6FA and API Standard API-607 for Trunnion ISO-5211 Top Flange, Anti-Static Device.
Ball Valves in accordance with API-6D.
8 www.walworth.com
QUALITY CONTROL EQUIPMENT
In order to assure that WALWORTH products comply with international quality standards, in-house equipment is kept for monitoring
control. Some of this equipment includes:
X-Ray Examination Equipment. WALWORTH has its own Ir-92 source

in-house for the radiographic examination (RT) of castings from 0.100” up to 2
1/2” wall thickness to verify the soundness of the casting raw material.
PMI Equipment. A new generation of Positive Material Identification Equipment

gives WALWORTH the capability to perform quick chemical analysis on incoming
raw materials and on pieces after assembly, to certify that materials used were
produced and assembled in accordance with WALWORTH’s and our Customer’s
specifications.
Magnetic Particle Test. On a random basis for standard products or when a

Customer requests MT Certification, WALWORTH has Magnetic Particle Test
Equipment to perform on ferromagnetic materials.
Penetrant Test Examination. WALWORTH has the personnel and materials to

perform PT examination by solvent removable or water washable techniques.
NDT personnel are ASNT Certified.
Test Loop. A complete Laboratory Test loop exists for design validation of
WALWORTH products. The test is performed at maximum design pressure,
advances the valves from 3000 to 5000 cycles, and requires more than four
months to complete.
Pressure Gradient Test Loop. This test exposes Plug valves to the extremes of
both positive and negative pressure gradients to verify that the plug in a balanced
plug design will prevent lock-up in the body.
www.walworth.com 9
Metrology Laboratory. WALWORTH developed a calibration and/or verification
system in all of the equipment used in its facilities. This ensures our ability to
trace measurements, control products, and comply with international standards.
Fire Test Facilities. WALWORTH has the facilities to perform fire tests in
accordance with API requirements. The test exposes the valve to a fire flame at
1400 to 1800 °F (761 to 980 °C) to verify proper seal of the valve.
Low Fugitive Emissions Test. This test is performed when a Customer requires
low fugitive emissions certification. Our Lab has its own LFE test equipment
that is capable of measuring less than 20 ppm in both static and mechanical
conditions at either ambient temperature or thermal cycle operations.
Ultrasonic Testing Equipment. Using ultrasonic techniques, we can detect

sub surface flaws in materials and evaluate castings and forgings that cannot
be radiographed. In addition, we utilize these techniques to measure the wall
thickness of castings and forgings.
Tensile Test Equipment. We use this equipment to verify the mechanical

properties of materials used for manufacturing. WALWORTH tests samples on a
random basis even though we receive MTRs from our suppliers and foundries.
Hardness Test Equipments.- In both lab and shop tests, WALWORTH uses
hardness tester equipment, such as Rockwell B, C Brinell or Vickers, to ensure
compliance with specifications.
10 www.walworth.com
(IRON AND CAST STEEL)
Advantages of Design
The main purpose of the DUAL PLATE WAFER CHECK valve is to perform the work of almost any conventional valve. However, being
smaller makes it lighter and, therefore, is more cost efficient to purchase, install and maintain. It is also a silent check valve; because
of it’s innovative design, it does not slam upon closing.
The DUAL PLATE WAFER CHECK plate design and flat seat offer many advantages. The flat seat eliminates any possibility of board
snaps in the seat, which snaps occur frequently in other valves. When suspended in a vertical pin, the two plates have a reduced
weight which eliminates excessive wear on the plate lugs. This wear can cause the plate to collapse on the seat’s open surface,
causing the valve to subsequently fail.
An important feature of the DUAL PLATE WAFER CHECK valve is that it does not depend on the pressure or flow to center the plates
in relation to the sealing surface in order to make the seal.
Single plate conventional designs, even those having centering guides, require a backpressure and backflow to center the plate to
the seat in order to get a non leakage adjustment. This feature becomes extremely risky in the event of reduced flow and the handling
of gases at low pressure.
Pressure by class according to

Size Ends
ASME/ANSI B16.34
2" a 60” 150, 300, 600, 900, 1500, 2500 RF, RTJ, P
www.walworth.com 11
DUAL PLATE WAFER CHECK VALVE LUG TYPE
Advantages of Design
With the aid of spring DUAL PLATE WAFER CHECK valve LUG type, as Wafer type, gives a maximum resistance with the minimum
opening time.
The stop pin avoids the over travel of a disc.
This design is also hermetic, which means there are no drillings in the body, and because there are now pins in a support that is
attached to the body, the chance of leakage is greatly reduced.
The DUAL PLATE WAFER CHECK valve LUG type covers the bolt along the entire length of the body.
LUG type valves are supplied in scallop to keep the weight as low as possible, thereby minimizing the cost.
LUG type valves are supplied with straight-through bores according to API-594.
Note:
1. For more information contact the company.
12 www.walworth.com
MOST COMMON MATERIAL OF THE BODY
Wrought bar
Material suffix Common designation Forging specification Service recommendations (1)
specification
ASTM A216 Grade Carbon Steel A105N A105N Non-corrosive applications including water, oil and
WCB gases at temperatures between -20°F (-30°F ) and
+800°F (+425°C)
ASTM A216 Grade Carbon Steel A105N A105N Non-corrosive applications including water, oil and
WCC gases at temperatures between -20°F (-30°F )and
+800°F (+425°C)
ASTM A217 Grade WC6 1 1/4% Chrome; 1/2% A182 F11 A182 F11 Class 2 Non-corrosive applications including water, oil and
Moly Low Alloy Steel gases at temperatures between -20°F (-30°C) and +
1100°F(+593°C).
ASTM A217 Grade WC9 2 1/4 % Chrome Low A182 F22 A182 F11 Class 3 Non-corrosive applications including water, oil and
Alloy Steel gases at temperatures between -20°F (-30°C) and +
1100°F(+593°C).
ASTM A352 Grade LCB Low Temp Carbon steel A350 LF1 A350 LF1 Low temperature applications to -50 °F (-46°C).Not
for use above + 650°F(+340°C).
ASTM A352 Grade LCC Low Temp Carbon steel A350 LF2 A350 LF2 Low temperature applications to -50 °F (-46°C).Not
for use above + 650°F(+340°C).
ASTM A351 Grade CF8 18% Chrome; 8% ASTM A182 F304 ASTM A479 304 Corrosive or extremely high temperature non-
Nickel; 0.08 % C corrosive services between -450°F (- 268°C) and +
Stainless Steel 1200°F (+649°C). Above + 800°F (+ 425°C) specify
carbon content of 0.04% or greater.
ASTM A351 Grade 18% Chrome; 12% ASTM A182 F316 ASTM A479 316 Corrosive or either extremely low or high temperature
CF8M Nickel; 2 % Mo; 0.08 % non-corrosive services between -450°F (-268°C) and
C Stainless Steel +1200°F (+649°C). Above +800°F (+425°C) specify
carbon content of 0.04% or greater.
ASTM A351 Grade CF3 18% Chrome; 8% ASTM A182 304L ASTM A479 304L Brackish water, phosphate solutions, pressurized
Nickel; 0.03 % C Low water @ 570 °F (299 °C), sea water, steam.
Carbon Stainless Steel
ASTM A351 Grade 18% Chrome; 12% ASTM A182 F316L ASTM A479 316L Acetic acid, calcium carbonate, calcium lactate,
CF3M Nickel; 2 % Mo; 0.03 % potable water, sea water, steam, sulfites.
C Low Carbon Stainless
Steel
ASTM A351 Grade 18% Chrome; 10% ASTM A182 F347 ASTM A479 347 Primarily for high temperature, corrosive applications
CF8C Nickel; Cb; 0.08 % C between -450°F (-268°C) and +1200°F (+649°C).
Stainless Steel Above +1000°F (+540°C) specify carbon content of
0.04% or greater. Hydrogen service.”
ASTM A351 Grade 19% Chrome; 28% ASTM B462 N08020 ASTM B473 N08020 Acetic acid (hot), brines, caustic solutions, (strong,
CN7M Nickel; Cu-Mo; 0.07 % C hot), hydrochloric acid (dilute), hydrofluoric acid and
Super Stainless Steel hydrofluosilicic acid (dilute), nitric acid, (strong, hot),
nitric-hydrofluoric pickling acids, sulfates and sulfites,
sulfuric acid, (all concentrations to 150 °F (65.6 °C),
sulfurus acid, phosphoric acid.
(1) The above list of consuming industries and corrosive materials are useful as examples of typical applications where these materials can be used as a guide; however,
the responsibility for choosing the proper alloy lies with the Engineering firm or End User.
(*) For other materials, please contact the company.
MOST COMMON TRIMS

Trim No. Parts and Materials
W1 Discs made from SS A351 Gr. CF8, Pin SS A276 Gr. 410, Stop Pin A276 Gr. 410
W2 Discs made from SS A351 Gr. CF8, Pin SS A276 Gr. F304, Stop Pin A276 Gr. F304
W3 Discs made from SS A351 Gr. CF8M, Pin SS A276 Gr. F316, Stop Pin A276 Gr. F316
W4 Discs made from SS A351 Gr. CF3, Pin SS A276 Gr. F304L, Stop Pin A276 Gr. F304L
W5 Discs made from SS A351 Gr. CF3M, Pin SS A276 Gr. F316L, Stop Pin A276 Gr. F316L
W6 Discs made from Duplex SS A995 Gr. CD3MN, Pin SS A182 Gr. F51, Stop Pin A182 Gr. F51
(*) For other TRIM materials, please contact the company.
www.walworth.com 13
CHEMICAL COMPOSITION OF MOST COMMON MATERIALS
Chemical composition and mechanical properties
Carbon steel Low carbon steel Low alloy steel Stainless steel
Elements and properties ASTM A216 ASTM A352 ASTMA217 ASTMA351
WCB WCC LCB LCC WC6 WC9 CF8 CF8M CF8C
Carbon 0.30 0.25 0.30 0.25 0.05-0.20 0.05-0.18 0.08 0.08 0.08
Manganese 1 1.2 1 1.2 0.50-0.80 0.40-0.70 1.5 1.5 1.5
Phosphorus 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04
Sulphur 0.045 0.045 0.045 0.045 0.045 0.045 0.04 0.04 0.04
Silicon 0.6 0.6 0.6 0.6 0.6 0.6 2 1.5 2
Nickel 0.5 0.5 0.5 0.5 - - 8.00-11.0 9.00-12.0 9.00-12.0
Chromium 0.5 0.5 0.5 0.5 1.00-1.50 2.00-2.75 18.00-21.0 18.00-21.0 18.00-21.0
Molybdenum 0.2 0.2 0.2 0.2 0.45-0.65 0.90-1.20 0.5 2.00-3.00 0.5
Copper 0.3 0.3 0.3 0.3 0.5 0.5 - - -
Columbium - - - - - - - - (2)
Vanadium 0.03 0.03 0.03 0.03 - - - - -
Tensile Strength PSI minimum 70,000- 70,000 65,000 70000- 70,000 70,000 70,000 70,000 70,000
95,000 95,000
Yield Strength PSI minimum 36,000 40,000 35,000 40,000 40,000 40,000 30,000 30,000 30,000
Elongation In 2"% minimum 22 22 24 22 20 20 35 30 30
Reduction Area "% minimum 35 35 35 35 35 35 - - -
Hardness (HB) maximum 185 185 190 200 200 200 - - -
Notes:
1. The percentage (%) shown on the elements is the maximum except where ranges are indicated.
2. Steel CF8C should have a Columbium content of not less than 8 times the carbon content, but not exceeding 1%.
SOFT SEATS OPERATING TEMPERATURE

Body Seat Operating Temperature
Buna - N -60 a 250 ºF (-5 a 120º C)
Viton -10 a 400 ºF (-23 a 204º C)
EPDM 0 a 300 ºF (-18 a 149º C)
Neoprene 0 a 212 ºF (-18 a 100º C)
Metal-Metal In accordance with B16,34
(*) We can supply another kind of seat as per customer request.
14 www.walworth.com
Design Features
• Design in accordance with API 594 1 Body. It’s 10% lighter than a conventional flanged check valve.
• End to end dimension as per API 594 2 Seat. Availability of soft seats and Metal-Metal.
• Flange dimensions in accordance with ASME B16.5, ASME
3 Disc in conjunction with springs, offers an airtight seal giving a
B16.47 better performance.
• Inspection and Test according to API 598 4 Springs give a better reaction to close.
• NACE MR-0175 Service
5 Shaft keeps discs in the position and avoids vibration.
• Availability LUG design
6 Shaft and stop pin are mounted on a support rather than through
• Availability Double Flange from 12”
holes in the body, resulting in a hermetic valve.
• Single Spring for 2” to 6”
• Double Spring for 8” and up
3 Discs Body 1
4 Springs Seat 2
6 Stop pin
Shaft 5
www.walworth.com 15
CLASS 150
Design Features
• Design in accordance with API 594 • NACE MR-0175 Service
• End to end dimension in accordance to API 594 • Lifting Lug for 8” and up
• Flange ends in accordance to ASME B16.5, ASME B16.47 • Single Spring for 2” to 6”
• Inspection and Test according to API 598 • Double Spring for 8” and up
10
Material List for Main Parts (Single Spring)

ASTM 2 1
No. Part Name
Carbon Steel
1 Body A216 WCB
2 Seat Seal A216 WCB + SS410 Overlay
3 Disc A351 CF8
4 Spring Inconel X-750

4
5 Shaft A276 Gr. 410
6 Stop Pin A276 Gr. 410 3

11
7 Shaft Support A276 Gr. 410
8 Retainer A276 Gr. 410
9 Bolting Commercial Steel
10 Lifting Lug Commercial Steel 5

11 Bearing A276 Gr. 410 6
7
Remark: 1. Select different materials for different working temperature and media. 8
9
10
Material List For Main Parts (Double Spring)

ASTM
No. Part Name 2 1
Carbon Steel
1 Body A216 WCB
3 Disc A351 CF8

4
4A Spring Inconel X-750 4A

3
6 Stop Pin A276 Gr. 410 11

5
9
16 www.walworth.com
CLASS 150
D1 D D2
D3
L1
Dimensions and Weights

Nominal
Dimension Pipe Flange
pipe size
Pressure / Weight
Flange standard (Kg) Bolt Stud Diameter (d) Stud Length (L1)
NPS CN L D1 D2 D D3
No. in mm RF RJ
2 50 60 103 56 51 2 120.5 4 5/8 M16 140 155
2 1/2 65 67 122 73 65 3 139.5 4 5/8 M16 150 165
3 80 73 135 88 80 4 152.5 4 5/8 M16 160 175
4 100 73 173 108 102 6 190.5 8 5/8 M16 170 185
5 125 86 195 132 127 8 216 8 3/4 M20 190 205
6 150 98 220 160 152 13 241.5 8 3/4 M20 205 220
Class 150 PN2,0/ 8 200 127 277 210 203 25 298.5 8 3/4 M20 240 255
ASME B16.5 10 250 146 337 266 254 39 362 12 7/8 M24 270 285
12 300 181 407 310 305 54 432 12 7/8 M24 310 325
14 350 184 448 355 350 80 476 12 1 M27 325 340
16 400 191 512 405 400 117 540 16 1 M27 340 355
18 450 203 547 455 450 138 478 16 1 1/8 M30 365 380
20 500 219 604 505 500 163 635 20 1 1/8 M30 385 400
24 600 222 715 605 600 331 749.5 20 1 1/4 M33 405 420
26 650 222 770 650 633 380 806.5 24 1 1/4 M33 450 -
28 700 305 827 700 700 400 863.5 28 1 1/4 M33 535 -
30 750 305 878 750 746 440 914.5 28 1 1/4 M33 545 -
32 800 305 935 800 796 580 978 28 1 1/2 M39x3 570 -
36 900 368 1045 894 874 660 1086 32 1 1/2 M39x3 650 -
Class 150 PN2,0/ 40 1000 432 1167 985 976 890 1200 36 1 1/2 M39x3 710 -
ASME B16.47A o
MSS SP-44 42 1050 432 1213 1055 1050 980 1257.5 36 1 1/2 M39x3 730 -
44 1100 432 1274 1070 1070 1150 1314.5 40 1 1/2 M39x3 730 -
48 1200 524 1397 1205 1166 1450 1422.5 44 1 1/2 M39x3 840 -
54 1350 591 1545 1315 1312 2300 1594 44 1 3/4 M45x3 950 -
56 1400 591 1602 1370 1360 2800 1651 48 1 3/4 M45x3 955 -
60 1500 660 1701 1470 1458 3220 1759 52 1 3/4 M45x3 1040 -
www.walworth.com 17
CLASS 300
Design Features

ASTM 2 1
No. Part Name
Carbon Steel 10
1 Body A216 WCB
3 Disc A351 CF8

4
9 Bolting Commercial Steel 5

6
10 Lifting Lug Commercial Steel
11 Bearing A276 Gr. 410
7
9
10

ASTM
No. Part Name 2 1
Carbon Steel
1 Body A216 WCB
3 Disc A351 CF8

4

11 3
6 Stop Pin A276 Gr. 410

5
9 Bolting Commercial Steel 6
8
Remark: 1. Select different materials for different working temperature and media.
9
18 www.walworth.com
CLASS 300
d
D1 D D2
D3
L1
L
Nominal
pipe size
Pressure / Weight
NPS CN L D1 D2 D D3
No. in mm RF RJ
2 50 60 110 58 51 3 127 8 5/8 M16 155 175
2 1/2 65 67 128 73 65 4 149 8 3/4 M20 175 195
3 80 73 147 88 80 6 168.5 8 3/4 M20 190 210
4 100 73 179 108 102 8 200 8 3/4 M20 195 215
5 125 86 214 132 127 15 235 8 3/4 M20 215 235
6 150 98 249 160 152 18 270 12 3/4 M20 230 250
Class 300 PN5,0/ 8 200 127 305 210 203 31 330 12 7/8 M24 280 300
ASME B16.5 10 250 146 359 266 254 51 387.5 16 1 M27 315 335
12 300 181 420 310 305 77 451 16 1 1/8 M30 365 385
14 350 222 483 355 350 117 514.5 20 1 1/8 M30 410 430
16 400 232 537 405 400 190 571.5 20 1 1/4 M33 435 455
18 450 264 594 455 450 200 628.5 24 1 1/4 M33 475 495
20 500 292 652 505 500 265 686 24 1 1/4 M33 510 535
24 600 318 772 608 600 410 813 24 1 1/2 M39x3 560 585
26 650 356 767 640 633 560 803 32 1 1/4 M33 625 -
28 700 368 821 985 685 580 857 36 1 1/4 M33 635 -
30 750 368 882 740 735 660 921 36 1 3/8 M36x3 650 -
32 800 368 936 784 784 970 978 32 1 1/2 M39x3 675 -
Class 300 PN5,0/ 36 900 483 1044 880 873 1010 1089 32 1 5/8 M42x3 800 -
ASME B16.47B o
API605 40 1000 546 1146 985 976 1420 1191 40 1 5/8 M42x3 885 -
42 1050 568 1196 1045 1035 1540 1244.5 36 1 3/4 M45x3 920 -
48 1200 629 1365 1190 1166 2250 1416 40 1 7/8 M48x3 1010 -
54 1350 718 1526 1315 1312 3100 1578 48 1 7/8 M48x3 1140 -
60 1400 838 1704 1470 1458 4310 1764 40 2 1/4 M56x3 1280 -
26 650 356 831 640 633 580 876 28 1 5/8 M42x3 625 -
28 700 368 895 985 685 600 940 28 1 5/8 M42x3 650 -
30 750 368 949 740 735 680 997 28 1 3/4 M45x3 665 -
32 800 368 1003 784 784 990 1054 28 1 7/8 M48x3 685 -
Class 300 PN5,0/ 36 900 483 1113 880 873 1050 1168.5 32 2 M52x3 820 -
ASME B16.47A o
MSS SP-44 40 1000 546 1110 985 976 1400 1156 32 1 5/8 M42x3 885 -
42 1050 568 1161 1045 1035 1520 1206.5 32 1 5/8 M42x3 915 -
48 1200 629 1320 1190 1166 2250 1371.5 32 1 7/8 M48x3 1015 -
54 1350 718 1489 1315 1312 3050 1594.5 28 2 1/4 M56x3 1160 -
60 1400 838 1642 1470 1458 4300 1702 32 2 1/4 M56x3 1305 -
www.walworth.com 19
CLASS 600
Design Features
10

ASTM 1
No. Part Name
Carbon Steel 2
1 Body A216 WCB
3 Disc A351 CF8

4
6 Stop Pin A276 Gr. 410 11 3

6
11 Bearing A276 Gr. 410
7
9
10

ASTM
No. Part Name 1
Carbon Steel
1 Body A216 WCB 2

3 Disc A351 CF8

4

3
7 Shaft Support A276 Gr. 410 6

11
7
9
Remark: 1. Select different materials for different working temperature and media.
20 www.walworth.com
CLASS 600
D1 D D2
D3
L1

Nominal
pipe size
Pressure / Weight
NPS CN L D1 D2 D D3
No. in mm RF RJ
2 50 60 110 58 51 4 127 8 5/8 M16 175 180
2 1/2 65 67 128 73 65 5 149 8 3/4 M20 195 200
3 80 73 147 88 80 8 168.5 8 3/4 M20 210 215
4 100 79 191 108 102 11 216 8 7/8 M24 235 240
5 125 105 139 136 127 20 267 8 1 M27 280 285
6 150 136 264 162 152 26 292 12 1 M27 320 325
Class 600 PN11,0/ 8 200 165 318 212 200 55 349 12 1 1/8 M30 370 375
ASME B16.5 10 250 213 398 266 250 95 432 16 1 1/4 M33 440 445
12 300 229 455 312 305 140 489 20 1 1/4 M33 460 465
14 350 273 490 355 337 223 527 20 1 3/8 M36x3 520 525
16 400 305 562 400 387 360 603 20 1 1/2 M39x3 575 580
18 450 362 610 450 438 395 654 20 1 5/8 M42x3 650 655
20 500 368 680 500 489 518 724 24 1 5/8 M42x3 670 680
24 600 438 786 600 591 836 838 24 1 7/8 M48x3 780 790
26 650 457 761 640 633 950 806.5 28 1 5/8 M42x3 790 805
Class 600 PN11,0/ 28 700 483 815 690 684 1210 863.5 28 1 3/4 M45x3 830 845
ASME B16.47B o 30 750 505 875 740 735 1370 927 28 1 7/8 M48x3 875 890
API605 32 800 533 928 784 779 1640 984 28 2 M52x3 920 940
36 900 635 1045 880 874 2120 1105 28 2 1/4 M56x3 1065 1085
26 650 457 863 640 633 980 915.5 28 1 7/8 M48x3 795 810
28 700 483 910 690 684 1250 965 28 2 M52x3 835 850
30 750 505 967 740 735 1420 1022.5 28 2 M52x3 860 905
Class 600 PN11,0/ 32 800 533 1020 784 779 1700 1079.5 28 2 1/4 M56x3 905 925
ASME B16.47A o
MSS SP-44 36 900 635 1126 880 874 2200 1194 28 2 1/2 M64x3 1035 1055
40 1000 660 1153 985 976 2650 1213 32 2 1/4 M56x3 1115 -
42 1050 701 1215 1030 1020 3120 1283 28 2 1/2 M64x3 1190 -
48 1200 787 1386 1170 1166 3720 1460.5 32 2 M70x3 1330 -
www.walworth.com 21
CLASS 900
Design Features
10

ASTM 1
No. Part Name
Carbon Steel
2
1 Body A216 WCB
3 Disc A351 CF8
4 Spring Inconel X-750 4
6 Stop Pin A276 Gr. 410 11 3

7
9
10

ASTM
No. Part Name 1
Carbon Steel
2
1 Body A216 WCB
3 Disc A351 CF8

4

3
6 Stop Pin A276 Gr. 410
8 Retainer A276 Gr. 410 5

6
11
9
22 www.walworth.com
CLASS 900
D1 D D2
D3
L1

Nominal
pipe size
Pressure / Weight
NPS CN L D1 D2 D D3
No. in mm RF RJ
2 50 70 140 58 51 8 165 8 7/8 M24 225 230
2 1/2 65 83 162 73 65 11 190.5 8 1 M27 250 255
3 80 83 165 90 80 14 190.5 8 7/8 M24 240 245
4 100 102 204 108 102 20 235 8 1 1/8 M30 285 290
5 125 110 245 136 127 30 278.5 8 1 1/4 M33 310 315
6 150 159 286 162 150 42 317.5 12 1 1/8 M30 365 370
Class 900 PN15,0/ 8 200 206 356 212 200 84 393.5 12 1 3/8 M36x3 440 445
ASME B16.5 10 250 241 432 266 250 145 470 16 1 3/8 M36x3 490 495
12 300 292 495 312 305 220 533.5 20 1 3/8 M36x3 560 565
14 350 356 518 355 337 350 559 20 1 1/2 M39x3 645 655
16 400 384 572 400 387 470 616 20 1 5/8 M42x3 685 695
18 450 451 635 450 438 605 686 20 1 7/8 M48x3 790 805
20 500 451 695 496 487 820 749.5 20 2 M52x3 810 825
24 600 495 835 600 591 1050 901.5 20 7/8 M64x3 945 965
www.walworth.com 23
CLASS 1500
Design Features
10

ASTM 1
No. Part Name
Carbon Steel
2
1 Body A216 WCB
3 Disc A351 CF8

4
6 Stop Pin A276 Gr. 410 11 3

7
9
10

ASTM
No. Part Name 1
Carbon Steel
2
1 Body A216 WCB
3 Disc A351 CF8 4


3
6

11
9
24 www.walworth.com
CLASS 1500
D1 D D2
D3
L1

Nominal
pipe size
Pressure / Weight
NPS CN L D1 D2 D D3
No. in mm RF RJ
2 50 70 140 58 51 8 165 8 1 M24 225 230
2 1/2 65 83 162 73 65 11 190.5 8 1 1/8 M27 250 255
3 80 83 172 90 80 19 203 8 1 1/4 M30 270 275
4 100 102 207 108 102 26 241.5 8 1 1/2 M33 310 315
Class 1500 PN26,0/ 5 125 110 252 136 127 51 292 8 1 3/8 M39 370 375
ASME B16.5 6 150 159 280 162 150 68 317.5 12 1 3/8 M36 430 440
8 200 206 350 212 200 130 393.5 12 1 5/8 M42 510 520
10 250 248 433 266 254 210 482.5 12 1 7/8 M48 600 610
12 300 305 518 312 305 384 517.5 16 2 M52 695 715
14 350 356 576 355 337 550 635 16 2 1/4 M56 775 800
16 400 384 639 400 387 635 705 16 2 1/2 M64 950 880
www.walworth.com 25
CLASS 2500
Design Features
10

ASTM 1
No. Part Name
Carbon Steel
2
1 Body A216 WCB
3 Disc A351 CF8

4

11

7
9
10

ASTM
No. Part Name 1
Carbon Steel
2
1 Body A216 WCB
3 Disc A351 CF8 4


3
6

11
9
26 www.walworth.com
CLASS 2500
D1 D D2
D3
L1

Nominal
pipe size
Pressure / Weight
NPS CN L D1 D2 D D3
No. in mm RF RJ
2 50 70 143 48 42 10 171.4 8 1 M27 260 260
2 1/2 65 83 166 58 52 18 196.8 8 1 1/8 M30 290 300
3 80 86 194 68 62 26 228.6 8 1 1/4 M33 315 325
4 100 105 232 94 88 40 273 8 1 1/2 M39x3 370 375
Class 2500 PN42,0/
5 125 110 277 106 100 59 323.8 8 1 3/4 M45x3 420 430
ASME B16.5
6 150 159 315 162 150 90 368.3 8 2 M52x3 515 525
8 200 206 385 186 180 150 438.2 12 2 M52x3 600 615
10 250 254 474 232 225 240 593.8 12 2 1/2 M64x3 760 780
12 300 305 547 272 266 440 619.1 12 2 3/4 M70x3 860 880
www.walworth.com 27
TECHNICAL INFORMATION
Easy Installation
The DUAL PLATE WAFER CHECK valve end to end dimensions allow an easy installation on standard flanges. Only one set of proper
length bolts is needed to cover the space of the DUAL PLATE WAFER CHECK valve. Since the valve is more rigid than an equivalent
length of heavy wall pipe, supports or special expansion joints are not required for installation.
Simplified Pipe Network

DUAL PLATE WAFER CHECK lightweight plates work in almost any position because of the spring action, allowing a greater versatility
and simple installation of the pipe. In some sizes, installation can be done even in vertical lines with flow down.
28 www.walworth.com
Effective Sealing Action
The DUAL PLATE WAFER CHECK valve’s resilient seal withstands high pressures without leak, distortion or damage. As shown in
the figure below, the sealing element is vulcanized into a slot on the body. This sealing element forms an “O” ring which is distorted
due to the pressure until metal to metal contact between the plate and the seal of the body occurs as shown in the figure bellow. The
seal is fully guarded to prevent damage under the pressure effect.
No Costly Foundations Required

Since the DUAL PLATE WAFER CHECK valve is placed between the pipe flanges, it does not need its own flanges; hence, the secret
of his low weight. For example, a steel valve ANSI 300 series 152.4 mm., (6”), weight is only 18.5 kg (41 lbs.) and can be installed
without special tools or equipment. It does not need expensive brackets or bases because the average weight of a DUAL PLATE
WAFER CHECK valve is less than 10% of a conventional flanged check valve.
www.walworth.com 29
Easy Maintenance
The DUAL PLATE WAFER CHECK valve consists of seven assembled parts, without fasteners or joints of any kind. All of these parts
are completely floating, without load on the pin, which is also fully floating. The new design eliminates blast-holes and allows total
hermeticity; because the pins are located in a support inside the valve, no drilling to the body is necessary.
The DUAL PLATE WAFER CHECK valve is much lighter and stronger than conventional valves.
When the opening is split in two, the thickness of the plates is reduced. The DUAL PLATE WAFER CHECK requires only one-eighth
the weight required of a conventional valve to bear an equivalent pressure.
The narrow compact body itself is stronger and more rigid than a short length of heavy wall pipe.
A simple heat-resistant stainless steel spring creates a positive seal, and rapid closure is made possible by lightweight plates. The
spring is specially designed for each valve and the low effort that is submitted, give high resistance to fatigue. The fast action of the
spring closes the valve before return flow can occur, thereby reducing the possibility of damage to water hammer.
Coefficients
Liquid Water flowing coefficient of the valves fully open under Flowing direction
Nominal pipe size resistance nominal temperature Vertical Horizontal
coefficient of
the valves fully Opening pressure approximation
DN NPS open Kv(m³/h) Cv (U.S) Cv (U.K)
(Kpa)
50 2 2.6 63 74 62 2 1
65 2 1/2 2.4 109 128 107 2 1
80 3 2.3 172 201 169 2 1
100 4 2 289 338 283 2 1
125 5 1.8 476 557 466 2 1
150 6 1.5 750 878 735 2 1
200 8 1.3 1432 1675 1403 2 1
250 10 1.2 2330 2726 2283 2 1
300 12 1 3676 4301 3602 2 1
350 14 0.9 5274 6171 5169 2 1
400 16 0.8 7306 8548 7160 3 1
450 18 0.8 9246 10818 9061 3 1
500 20 0.8 11415 13356 11187 3 1
600 24 0.7 17573 20560 17222 3 1
700 28 0.7 23919 27985 23441 4 1
750 30 0.7 27458 32126 26909 4 1
800 32 0.7 31241 36552 30616 4 1
900 36 0.7 39539 46261 37848 4 1
1000 40 0.7 48814 57112 47838 4 1
1050 42 0.7 53817 62966 52741 4 1
1100 44 0.7 — — — 4 1
1200 48 0.7 70292 82242 68886 4 1
1350 54 0.7 — — — 4 1
1400 56 0.7 — — — 4 1
1500 60 0.7 — — — 4 1
30 www.walworth.com
Production Line DUAL PLATE WAFER CHECK valve
Size Pressure (CLASS)
DN NPS 150 300 600 900 1500 2500
50 2 • • • • • •
65 2 1/2 • • • • • •
80 3 • • • • • •
100 4 • • • • • •
125 5 • • • • • •
150 6 • • • • • •
200 8 • • • • • •
250 10 • • • • • •
300 12 • • • • • •
350 14 • • • • •
400 16 • • • • •
450 18 • • • •
500 20 • • • •
600 24 • • • •
650 26 • • •
700 28 • • •
750 30 • • •
800 32 • • •
900 36 • • •
1000 40 • •
1050 42 • •
1100 44 • •
1200 48 • •
1350 54 • •
1400 56 •
1500 60 • •
PRESSURE-TEMPERATURE RATINGS
CAST STEEL ASTM A 216 GR WCB
MAXIMUM ALLOWABLE NON-SHOCK WORKING PRESSURE IN PSIG BY CLASS
°F Temperature °C
150 300 600 900 1,500 2500
-20 a 100 -29 a 38 285 740 1,480 2,220 3,705 6,170
200 93 260 680 1,360 2,035 3,395 5,655
300 149 230 655 1,310 1,965 3,270 5,450
400 204 200 635 1,265 1,900 3,170 5,280
500 260 170 605 1,205 1,810 3,015 5,025
600 316 140 570 1,135 1,705 2,840 4,730
650 343 125 550 1,100 1,650 2,745 4,575
700 371 110 530 1,060 1,590 2,665 4,425
750 399 95 505 1,015 1,520 2,535 4,230
800 427 80 410 825 1,235 2,055 3,430
850 454 65 320 640 955 1,595 2,655
900 482 50 230 460 690 1,150 1,915
950 510 35 135 275 410 685 1,145
1,000 538 20 85 170 255 430 715
Note: Upon prolonged exposure to temperatures above 800°F, the carbide phase of steel may be converted to graphite. Permissible, but not recommended for prolonged
use above 800°F.
www.walworth.com 31
CAST STEEL ASTM A 217 GR WC6
Maximum allowable non-shock working pressure in PSIG by class
°F Temperature °C
150 300 600 900 1500 2500
-20 to 100 -29 to 38 290 750 1,500 2,250 3,750 6,250
200 93 260 750 1,500 2,250 3,750 6,250
300 149 230 720 1,445 2,165 3,610 6,015
400 204 200 695 1,385 2,080 3,465 5,775
500 260 170 665 1,330 1,995 3,325 5,540
600 316 140 605 1,210 1,815 3,025 5,040
650 343 125 590 1,175 1,765 2,940 4,905
700 371 110 570 1,135 1,705 2,840 4,730
750 399 95 530 1,065 1,595 2,660 4,430
800 427 80 510 1,015 1,525 2,540 4,230
850 454 65 485 975 1,460 2,435 4,060
900 482 50 450 900 1,350 2,245 3,745
950 510 35 320 640 955 1,595 2,655
1,000 538 20 215 430 650 1,080 1,800
1,050 566 20(a) 145 290 430 720 1,200
1,100 593 20(a) 95 190 290 480 800
1,150 621 20(a) 65 130 195 325 545
1,200 649 15(a) 40 80 125 205 345
Notes:
• Use normalized and tempered material only.
• Not to be used over 1,100°F.
• The deliberate addition of any element not listed in ASTM A 217, Table 1 is prohibited, except that Ca and Mg may be added for deoxidation.
(a) Flanged-end valve ratings terminate at 1,000°F (538°C).
CAST STEEL ASTM A 217 GR WC9

°F Temperature °C
150 300 600 900 1500 2500
-20 to 100 -29 to 38 290 750 1,500 2,250 3,750 6,250
200 93 260 750 1,500 2,250 3,750 6,250
300 149 230 730 1,455 2,185 3,640 6,070
400 204 200 705 1,410 2,115 3,530 5,880
500 260 170 665 1,330 1,995 3,325 5,540
600 316 140 605 1,210 1,815 3,025 5,040
650 343 125 590 1,175 1,765 2,940 4,905
700 371 110 570 1,135 1,705 2,840 4,730
750 399 95 530 1,065 1,595 2,660 4,430
800 427 80 510 1,015 1,525 2,540 4,230
850 454 65 485 975 1,460 2,435 4,060
900 482 50 450 900 1,350 2,245 3,745
950 510 35 385 755 1,160 1,930 3,220
1,000 538 20 265 535 800 1,335 2,230
1,050 566 20(a) 175 350 525 875 1,455
1,100 593 20(a) 110 220 330 550 915
1,150 621 20(a) 70 135 205 345 570
1,200 649 15(a) 40 80 125 205 345
Notes:
• Use normalized and tempered material only.
• Not to be used over 1,100°F.
• The deliberate addition of any element not listed in ASTM A 217, Table 1 is prohibited, except that Ca and Mg may be added for deoxidation.
(a) Flanged-end valve ratings terminate at 1,000°F.
CAST STEEL ASTM A 352 GR LCB

°F Temperature °C
150 300 600 900 1500 2500
-20 to 100 -29 to 38 265 695 1,395 2,090 3,480 5,805
200 93 255 660 1,320 1,980 3,300 5,505
300 149 230 640 1,275 1,915 3,190 5,315
400 204 200 615 1,230 1,845 3,075 5,125
500 260 170 585 1,175 1,760 2,930 4,885
600 316 140 550 1,105 1,655 2,755 4,595
650 343 125 535 1,065 1,600 2,665 4,440
700 371 110 510 1,025 1,535 2,560 4,270
750 399 95 475 955 1,430 2,385 3,970
800 427 80 390 780 1,175 1,955 3,255
850 454 65 300 595 895 1,490 2,485
900 482 50 200 405 605 1,010 1,685
950 510 35 135 275 410 685 1,145
1000 538 20 85 170 255 430 715
Notes:
Not to be used over 650°F.
32 www.walworth.com
CAST STEEL ASTM A 351 GR CF8
°F Temperature °C
150 300 600 900 1,500 2,500
-20 a 100 -29 a 38 275 720 1,440 2,160 3,600 6,000
200 93 230 600 1,200 1,800 3,000 5,000
300 149 205 540 1,075 1,615 2,690 4,480
400 204 190 495 995 1,490 2,485 4,140
500 260 170 465 930 1,395 2,330 3,880
600 316 140 440 885 1,325 2,210 3,680
650 343 125 430 865 1,295 2,160 3,600
700 371 110 420 845 1,265 2,110 3,520
750 399 95 415 825 1,240 2,065 3,440
800 427 80 405 810 1,215 2,030 3,380
850 454 65 395 790 1,190 1,980 3,300
900 482 50 390 780 1,165 1,945 3,240
950 510 35 380 765 1,145 1,910 3,180
1,000 538 20 355 710 1,065 1,770 2,950
1,050 566 20(a) 325 650 975 1,630 2,715
1,100 593 20(a) 255 515 770 1,285 2,145
1,150 621 20(a) 205 410 615 1,030 1,715
1,200 649 20(a) 165 330 495 825 1,370
1,250 677 20(a) 135 265 400 970 1,115
1,300 704 20(a) 115 225 340 565 945
1,350 732 20(a) 95 185 280 465 770
1,400 760 20(a) 75 150 225 380 630
1,450 788 20(a) 60 115 175 290 485
1,500 816 15(a) 40 85 125 205 345
Notes: At temperatures over 1,000°F, use only when the carbon content is 0.04% or higher. (a) Flanged ends ratings terminate at 1000°F (538°C).
CAST STEEL ASTM A 351 GR CF8M

°F Temperature °C
150 300 600 900 1,500 2,500
-20 a 100 -29 a 38 275 720 1,440 2,160 3,600 6,000
200 93 235 620 1,240 1,860 3,095 5,160
300 149 215 560 1,120 1,680 2,795 4,660
400 204 195 515 1,025 1,540 2,570 4,280
500 260 170 480 955 1,435 2,390 3,980
600 316 140 450 900 1,355 2,255 3,760
650 343 125 440 885 1,325 2,210 3,680
700 371 110 435 870 1,305 2,170 3,620
750 399 95 425 855 1,280 2,135 3,560
800 427 80 420 845 1,265 2,110 3,520
850 454 65 420 835 1,255 2,090 3,480
900 482 50 415 830 1,245 2,075 3,460
950 510 35 385 775 1,160 1,930 3,220
1,000 538 20 365 725 1,090 1,820 3,030
1,050 566 20 360 720 1,080 1,800 3,000
1,100 593 20(a) 305 610 915 1,525 2,545
1,150 621 20(a) 235 475 710 1,185 1,970
1,200 649 20(a) 185 370 555 925 1,545
1,250 677 20(a) 145 295 440 735 1,230
1,300 704 20(a) 115 235 350 585 970
1,350 732 20(a) 95 190 290 480 800
1,400 760 20(a) 75 150 225 380 630
1,450 788 20(a) 60 115 175 290 485
1,500 816 15(a) 40 85 125 205 345
Notes: At temperatures over 1,000°F, use only when the carbon content is 0.04% or higher. (a) Flanged ends ratings terminate at 1000°F (538°C).
www.walworth.com 33
PRESSURE DROP OR FORCE LOSS THROUGH THE VALVE AT A FLOW RATE
OF 3.048 M/SEC (10 FT/SEC) OF WATER AT 155°C (60°F)
Tamaño de la válvula Gasto Pérdida de presión Pérdida de carga Equivalencia tubería C-100 P
mm pulg. lt/seg GPM Kg/cm2 lb/pulg.2 mts pies mts pies
50.8 2 6.50 103 0.320 4.55 3.2 10.5 9.4 31
65 2 1/2 9.40 149 0.246 3.76 2.7 8.7 10.1 33
75 3 14.51 230 0.213 3.03 2.1 7.0 10.7 35
100 4 25.49 404 0.165 2.34 1.6 5.4 11.3 37
125 5 39.31 623 0.134 1.90 1.3 4.4 11.3 37
150 6 56.78 900 0.110 1.56 1.1 3.6 11.6 38
200 8 97.79 1550 0.085 1.21 0.85 2.8 12.5 41
250 10 160.20 2540 0.067 0.95 0.67 2.2 12.8 42
300 12 220.80 3500 0.058 0.825 0.58 1.9 13.7 45
350 14 270.00 4280 0.052 0.740 0.52 1.7 14.3 47
400 16 359.60 5700 0.043 0.611 0.43 1.4 14.3 47
450 18 499.70 7920 0.040 0.569 0.40 1.3 14.6 48
500 20 567.80 9000 0.037 0.526 0.37 1.2 15.2 50
600 24 946.20 15000 0.030 0.424 0.30 0.98 15.8 52
900 36 2000.00 31700 0.020 0.284 0.20 0.65 16.5 54
1200 48 3558.00 56400 0.015 0.216 0.15 0.50 18.3 60
* This table is valid for API and ANSI valves.
34 www.walworth.com
DROP PRESSURE OR FORCE LOSS GRAPHIC
Force loss in meters of water
orce loss in feet of water
Losses indicated are based on water at 15.5° C (60° F) and

a specific gravity of 1.0
50.8 mm (2”) valve
63.5 mm (2 1/2”)
76.2 mm (3”)
gallons per second
liters per second
101.6 mm (4”)
127.0 mm (5”)
152.4 mm (6”)
203.2 mm (8”)
254.0 mm (10”)
304.8 mm (12”)
355.6 mm (14”)
406.4 mm (16”)
457.2 mm (18”)
508.0 mm (20”)
609.6 mm (24”)
762 mm (30”)
914.4 mm (36”)
1219.2 mm (48”)
* This table is valid for API and ANSI valves.
www.walworth.com 35
DESIGN BASIS
All of WALWORTH’s Valve Designs, when applicable, follow one or more of the following standards.
API American Petroleum Institute:
API 594 Check Valves: Flanged, Lug, Wafer and Butt-welding.
API 598 Valve Inspection and Testing.
ASME/ANSI American National Standard Institute:

B16.34 Pressure-Temperature Range.
B16.10 Length of Ferrous Flanged and Welding end valve.
B16.5 Steel pipe Flanges and Flanged Fittings.
B16.47 Large Diameter Steel Flanges.
ASTM American Society for Testing and Materials:

A-216 Standard specification for steel casting, carbon, suitable for fusion welding, for high temperature service.
A-351 Standard specification for casting, austenitic, austenitic-ferritic (duplex), for pressure containing parts.
A-352 Standard specification for steel casting, ferritic and martensitic, for pressure-containing parts, suitable for
low temperature service.
NACE National Association of Corrosion Engineers:

MR 0175 Standard material requirements sulfide stress cracking resistant metallic materials for oilfield equipment.
MSS Manufactures Standardization Society of the Valve and Fittings:

SP-25 Standard marking system for valves, fittings, flanges and unions.
SP-44 Steel pipeline flanges.
36 www.walworth.com
HOW TO ORDER
The figure of Example 24” H6SPF describes a valve 24” nominal diameter, style H (standard design), ANSI class 600#,
with carbon steel body (WCB), metal to metal seal, serrated face, W1 describes discs made of SS Gr. CF8, shaft SS Gr.
410 and stop pin SS Gr. 410.
24” H 6 S P F W1
TRIM
ENDS
BODY SEAT
BODY
CLASS
MODEL
SIZE
Base Figure
Model Class Body Body seat Ends
B Al-Bronze
D Double Flange 1 150 E EPDM F Serrated Face
C CF8M/SS316
D CF8/SS304
Wafer Standard
H 3 300 M Buna-N R Ring Type Joint
Design
G LCB
I CF3/SS304L
Plain Face (non
L Lug 6 600 P Metal-Metal Seal P
serrated)
J LC3
K CF3M/SS316L
9 900 V Viton
M Monel
N CD3MN
5 1500 N Neoprene
S WCB
2 2500
www.walworth.com 37
THE WALWORTH COMPANY GENERAL TERMS AND CONDITIONS
ACCEPTANCE: All quotations are for acceptance within 30 days from date of order will not be released for manufacture until complete specifications and
quotation unless extended in writing. In the event a purchase order is placed approved drawings (if drawing approval is required) are received at the plant of
after this period of time. The WALWORTH Company reserves the right to manufacture and the estimated schedule of shipment will commence with the
requote base prices of all valves offered. All orders and contracts are subject to date of such receipt.
credit approval and acceptance by the WALWORTH Company.
Seller shall not be liable for any direct, indirect or consequential damage or loss
FREIGHT: When prices are FOB point of shipment –no freight allowance, we caused by any delay in delivery, regardless of the cause of delay.
will attempt to route shipments in the method which will result in the lowest cost Without limiting the generality of the foregoing, Seller assumes no responsibility
unless otherwise instructed. All shipments will be freight charges collect except for delays in delivery resulting from fire, flood, accidents, riots, strikes,
when stipulated on the purchase order, in which case you will be invoiced transportation delays, labor or material shortages, existing or future laws, acts
for all transportation charges. Delivery of material to a common carrier shall of any governmental authority, or any other cause beyond Seller’s control.
be considered to be delivery to Buyer and shall be at Buyer’s risk thereafter. Items offered from stock are subject to prior sale.
Claims of loss of or damage to material in transit shall be filed by the Buyer
directly with the carrier. INSPECTION: Final inspection and acceptance of products must be made at
the plant of manufacture, unless otherwise provided in the order and/ or in
PRICES: There will be added to all prices quoted sales, use, occupation or agreed upon specifications. Prices do not include charges for special tests or
any other excise or similar tax which Seller may be required to pay or collect inspections performed at the request of the Buyer, unless called for in the order
on or in connection with the sale. Seller shall be established by Federal, State and/or in agreed upon specifications.
or other government regulation with respect to the product(s) covered by the
order which shall be lower than the price(s) specified in the order. RETURNS: Permission in writing and return tagging instructions must be
obtained from Seller before any goods returned for credit or adjustment will be
ESCALATION TERMS: Prices shown in this price schedule reflect the costs in acceptance. Where returned goods are accepted, a minimum charge of 25%
effect at the time of publication. These prices will remain firm on all products of the invoice price will be made, plus freight from both directions and costs of
with a quoted delivery of twenty–six (26) weeks or less. On products which reconditioning the material for resale as new.
have a scheduled delivery of more than twenty-six (26) weeks, the goods
will be invoiced based on the applicable price sheet in effect at the time of WARRANTY CERTIFICATE: WALWORTH, exhibits this product Warranty, for
shipment. In no event will the invoiced price be less than the price originally a 12 month period in operation or 18 months in storage, whatever comes firs
quoted. as of the date of product delivery.
PURCHASED COMPONENTS: (i.e. motors, gearing, etc.) Prices are quoted WALWORTH, guarantees that products are fabricated according to quality,
on supplier price in effect at time of quotation. Actual invoice Price will be design and manufacturing standards and customer requirements as well.
adjusted in accordance with the supplier’s escalation policy. When the buyer expressly and in written confirms the non-compliance of such
standards, WALWORTH is forced to comply with the repair, replacement or
DEFERRED SHIPMENTS: If for any reason the customer desires to delay to issue the written authorization for the buyer or another agent, to replace or
shipments more than 30 days after manufacturing is complete or to place a repair at no cost for the buyer, at WALWORTH fabrication costs, those parts
hold or stop to the order during the manufacturing cycle, The WALWORTH confirmed as defective.
Company reserves the right to consider the order cancelled and to invoke
cancellation charges per the schedule bellow. This warranty is valid when the material selection by the customer for the design,
material arrangement (TRIM, bodies, ends, operation devices, etc.) internal and/
CANCELLATION: After order acceptance by WALWORTH, items or completed or external overlays had been the proper ones for the operation fluid.
orders may be cancelled and buyer will be charged for work performed, based This warranty is applicable if operation and service conditions are maintained
on the following schedule: as per the requirements of the product.
- Five (5%) percent of prices of stock items. To validate the Warranty, the user is responsible of performing the proper
- Ten (10%) percent of price of stock items ordered in quantities which exceed maintenance according to what is stated in the Operation and Maintenance
normal inventory levels. Manual applicable to the product. WALWORTH, reserves the right to request
- Five (5%) percent of prices prior to drawing submittal on made-to-order items. the records (evidence) to confirm the correct maintenance.
- 15% after drawing approval, but prior to the start of castings.
- 30% to 50% during casting cycle, depending on the state of completion. WALWORTH obligations are limited and will be released of any responsibility
- 55% to 75% during machining and assembly operations, depending on the when the products are altered, repaired or replaced without WALWORTH’ s
state of completion. written authorization.
-100% after final assembly and test.
Except of what is stated in this document WALWORTH waives and excludes
REMITTANCES: Remittances must be made to the address indicated on the any other warranty expressed or implied, for loss, direct damage, indirect
invoice. damage or consequential of other products, processes, installations or
equipment of the buyer or end user, either partial or total, due to material
CREDIT TERMS: As quoted. Invoices on balances overdure will be subject to defects and/or work and/or WALWORTH product design.
a service charge of 11/2 % per month on such indebtedness.
DESIGN, ETC: Seller reserves the right to change design, materials or
DELIVERIES: Shipments and deliveries shall at all times be subject to the specifications without notice. There will be a charge for modifying an order
approval of Seller’s Credit Department. If the Buyer shall fail to make any after it has been entered when such change or modification results in additional
payments according to the terms of the contract, Seller may, in addition to engineering or clerical work for either The WALWORTH Company or our
and not in limitation of its other rights and remedies, at its option, cancel all or suppliers.
any part of Buyer’s incomplete contracts with Seller or may defer shipments
of deliveries under Buyer’s contracts with Seller except upon receipt of MINIMUM CHARGE: Orders totaling less than $100.00 USD net will be billed
satisfactory security or for cash shipment. at a minimum charge of $100.00 USD. Repair parts will be billed at a minimum
All schedule of shipments are estimated as closely as possible and Seller will charge of $50.00 USD.
use its best efforts to ship within the time scheduled, but does not guarantee
to do so. Schedules commence with the date Seller receives authorization NOTE: We reserve the right to correct obvious clerical errors in quotations,
to proceed with order, subject to the provisions of the next sentence. The invoices, and other contracts.
38 www.walworth.com
www.walworth.com
MÉXICO
Industrial de Válvulas, S.A. de C.V.

Industria Lote 16 Sin Número, Fracc. Industrial El Trébol De Tepotzotlán, Tepotzotlán Estado de México C.P. 54610
Phone: (52 55) 5899 1700 Fax: (52 55) 5876 0156 | e-mail: [email protected]
USA/CAN Authorized Distributor
TWC The Valve Company

13641 Dublin Court, Stafford, Texas 77477 | Phone: (281) 566 1200 Fax: (281) 566 1299 |
www.twcvalves.com | e-mail: [email protected]
Scan me with your smartphone to get

more info about WALWORTH valves
DUAL PLATE WAFER CHECK VALVE | 2017 EDITION | VERSION 1

Catalog: Dual Plate Wafer Check Valve

Uploaded by

Copyright:

Available Formats

Catalog: Dual Plate Wafer Check Valve

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Catalog: Dual Plate Wafer Check Valve

Uploaded by

Copyright:

Available Formats

DUAL PLATE WAFER CHECK VALVE

QUALITY CONTROL EQUIPMENT.......................................................................................................................... 9

WAFER TYPE VALVES DOUBLE DISC.................................................................................................................11

WAFER LUG TYPE VALVES DOUBLE DISC....................................................................................................... 12

MOST COMMON MATERIAL OF THE BODY...................................................................................................... 13

MOST COMMON TRIMS.......................................................................................................................................... 13

CHEMICAL COMPOSITION OF MOST COMMON MATERIALS...................................................................... 14

OPERATING TEMPERATURE FOR SOFT SEATS............................................................................................. 14

DUAL PLATE WAFER CHECK VALVE CLASS 150........................................................................................... 16

DUAL PLATE WAFER CHECK VALVE CLASS 300........................................................................................... 18

DUAL PLATE WAFER CHECK VALVE CLASS 600........................................................................................... 20

DUAL PLATE WAFER CHECK VALVE CLASS 900........................................................................................... 22

DUAL PLATE WAFER CHECK VALVE CLASS 1500......................................................................................... 24

DUAL PLATE WAFER CHECK VALVE CLASS 2500......................................................................................... 26

DROP PRESSURE OR FORCE LOSS GRAPHIC............................................................................................... 35

TERMS AND CONDITIONS..................................................................................................................................... 38

WALWORTH relies on its broad experience in supplying valves to the

Our manufacturing system includes: utilization of Company directed

WALWORTH is capable of providing the world´s most comprehensive

Our designs are made using the most advanced technology

WALWORTH QUALITY SYSTEM

Certificate API-6D No. 6D-0097 Certificate API-6A No. 6A-0234

Certificate ISO-9001 No. 0038

API-600 Certificate No. 600-0109

API-602 Certificate No. 602-0024

Emissions after 500 cycles at ambient and 350 °F

X-Ray Examination Equipment. WALWORTH has its own Ir-92 source

PMI Equipment. A new generation of Positive Material Identification Equipment

Magnetic Particle Test. On a random basis for standard products or when a

Penetrant Test Examination. WALWORTH has the personnel and materials to

Ultrasonic Testing Equipment. Using ultrasonic techniques, we can detect

Tensile Test Equipment. We use this equipment to verify the mechanical

Pressure by class according to

MOST COMMON TRIMS

(*) For other TRIM materials, please contact the company.

Elements and properties ASTM A216 ASTM A352 ASTMA217 ASTMA351

WCB WCC LCB LCC WC6 WC9 CF8 CF8M CF8C

Manganese 1 1.2 1 1.2 0.50-0.80 0.40-0.70 1.5 1.5 1.5

Silicon 0.6 0.6 0.6 0.6 0.6 0.6 2 1.5 2

Nickel 0.5 0.5 0.5 0.5 - - 8.00-11.0 9.00-12.0 9.00-12.0

Copper 0.3 0.3 0.3 0.3 0.5 0.5 - - -

Vanadium 0.03 0.03 0.03 0.03 - - - - -

Elongation In 2"% minimum 22 22 24 22 20 20 35 30 30

Reduction Area "% minimum 35 35 35 35 35 35 - - -

Hardness (HB) maximum 185 185 190 200 200 200 - - -

SOFT SEATS OPERATING TEMPERATURE

Buna - N -60 a 250 ºF (-5 a 120º C)

Viton -10 a 400 ºF (-23 a 204º C)

EPDM 0 a 300 ºF (-18 a 149º C)

Neoprene 0 a 212 ºF (-18 a 100º C)

Metal-Metal In accordance with B16,34

(*) We can supply another kind of seat as per customer request.

Material List for Main Parts (Single Spring)

1 Body A216 WCB

2 Seat Seal A216 WCB + SS410 Overlay

3 Disc A351 CF8

4 Spring Inconel X-750

6 Stop Pin A276 Gr. 410 3