Professional Documents
Culture Documents
User Operation Manual: Eclipse 8 Eclipse 16 Eclipse 32
User Operation Manual: Eclipse 8 Eclipse 16 Eclipse 32
OPERATION
MANUAL
ECLIPSE 8
ECLIPSE 16
ECLIPSE 32
(S.W. 2.0x)
Attention:
This manual contains information on limitations regarding product use and
function and information on the limitations as to liability of the manufacturer.
The entire manual should be carefully read.
Table of Contents:
1. GENERAL INFORMATION ............................................................................................ 5
2. SUPPORTED KEYBOARDS .......................................................................................... 6
2.1 LED Keyboards ........................................................................................................ 6
2.2 LCD Keyboards ........................................................................................................ 6
2.3 Buttons Functionality ................................................................................................ 7
2.4 Indication.................................................................................................................. 8
2.5 Sound Signalization ................................................................................................. 9
2.6 Directions for Operation with LED Keyboards .......................................................... 9
2.6.1 Special indication used in LED 8 and LED 16A keyboards .............................. 9
2.6.2 Special indication for reviewing of address number (LED 8 and LED 16A) .... 10
2.6.3 Programming by Manager .............................................................................. 10
2.6.4 Programming by User ..................................................................................... 10
2.7 Directions for Operation with LCD Keyboards ........................................................ 11
2.8 Entering Text with LCD Keyboards ........................................................................ 11
3. OPERATION INSTRUCTIONS .................................................................................... 12
3.1 Arming With a Keyboard ........................................................................................ 12
3.1.1 Full Arming Mode ............................................................................................ 12
3.1.2 Stay Arming Mode .......................................................................................... 12
3.1.3 Sleep Arming Mode ........................................................................................ 12
3.1.4 Arming All Available Areas in the System ....................................................... 13
3.1.5 Viewing the Status of the Areas ...................................................................... 13
3.1.6 Reviewing the Open Zones............................................................................. 14
3.1.7 Changing the Arming Mode without Disarming ............................................... 15
3.2 Arming Via a Card Reader or BRAVO Remote Key Fob........................................ 15
3.2.1 Arming via Built-in Proxy Reader in Keyboard ................................................ 15
3.2.2 Arming via Stand-alone Proxy Reader PR IT and Eclipse PR ........................ 16
3.2.3 Arming via BRAVO RC Remote Key Fob ....................................................... 16
3.3 Disarming ............................................................................................................... 17
3.3.1 Disarming via keyboard .................................................................................. 17
3.3.2 Disarming via built-in card reader in a keyboard ............................................. 17
3.3.3 Disarming via stand-alone proxy reader ......................................................... 17
3.3.4 Disarming via BRAVO RC Key Fob ................................................................ 17
3.4 Stopping the Sounders........................................................................................... 18
3.5 Panic Buttons ......................................................................................................... 18
3.6 Ambush Code ........................................................................................................ 18
3.7 Technical Troubles Review .................................................................................... 18
3.8 Checking the Bypassed Zones .............................................................................. 20
4. USERS’ PROGRAMMING MENUS ............................................................................. 20
4.1 Changing own code ............................................................................................... 21
4.2 Memory LOG review by User ................................................................................. 21
4.3 Turning on the Chime signalization by User ........................................................... 22
4.4 Zone bypassing by User ........................................................................................ 23
5. MANAGERS’ PROGRAMMING MENUS ..................................................................... 24
5.1 Creating and Changing User codes ....................................................................... 25
5.2 Deleting User codes ............................................................................................... 25
5.3 Memory LOG review by Manager .......................................................................... 25
5.4 Turning on the Chime signalization by Manager .................................................... 26
5.5 Zones bypassing by Manager ................................................................................ 26
2
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
3
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
GUARANTEE
The guarantee terms are determined by the serial number (barcode) of the electronic device!
During the guarantee period the manufacturer shall, at its sole discretion, replace or repair any defective product
when it is returned to the factory. All parts replaced and/or repaired shall be covered for the remainder of the
original guarantee, or 6 months, whichever period is longer. The original purchaser shall immediately send
manufacturer a written notice of the defective parts or workmanship.
INTERNATIONAL GUARANTEE
Foreign customers shall possess the same guarantee rights as those any customer in Bulgaria, except that
manufacturer shall not be liable for any related customs duties, taxes or VAT, which may be payable.
GUARANTEE PROCEDURE
The guarantee will be granted when the appliance in question is returned. The guarantee period and the period for
repair are determined in advance. The manufacturer shall not accept any product, of which no prior notice has been
received via the RAN form at: http://www.teletek-electronics.com/en/support/Service
The setup and programming included in the technical documentation shall not be regarded as defects. Teletek
Electronics bears no responsibility for the loss of programming information in the device being serviced.
WAIVER
This Guarantee shall contain the entire guarantee and shall be prevailing over any and all other guarantees, explicit
or implicit (including any implicit guarantees on behalf of the dealer, or adaptability to specific purposes), and over
any other responsibilities or liabilities on behalf of the manufacturer. The manufacturer does neither agree, nor
empower, any person, acting on his own behalf, to modify, service or alter this Guarantee, nor to replace it with
another guarantee, or another liability with regard to this product.
UNWARRANTED SERVICES
The manufacturer shall repair or replace unwarranted products, which have been returned to its factory, at its sole
discretion under the conditions below. The manufacturer shall accept no products for which no prior notice has been
received via the RAN form at: http://www.teletek-electronics.com/en/support/Service .
The products, which the manufacturer deems repairable, will be repaired and returned. The manufacturer has
prepared a price list and those products, which can be repaired, shall be paid for by the Customer. The devices with
unwarranted services carry 6 month guarantee for the replaced parts.
The closest equivalent product, available at the time, shall replace the products, the manufacturer deems un-
repairable. The current market price shall be charged for every replaced product.
4
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
1. GENERAL INFORMATION
ECLIPSE Series are control panels providing security and management of small and
medium residential or office sites.
The ECLIPSE family includes:
ECLIPSE 8 for management of small sites up to 8 zones organized in 1 common
area and for up to 8 users.
ECLIPSE 16 for management of small to medium sites up to 16 zones organized in 3
independent areas and for up to 32 users.
ECLIPSE 32 for management of medium sites up to 32 zones and 8 independent
areas and for up to 64 users.
In ECLIPSE Series control panels are available two types of users: Managers and
Regular users of the system. The Managers have extended rights for programming of
special system menus and the regular users have limited rights for operation with the
system.
Manager of the system can be every user, who has been granted manager rights. User 1
is the Chief Manager and his/her rights cannot be changed. The users can be granted
manager rights by the Engineer of the system, as well as by another Manager of the
system with programming rights.
The Manager programming menu is structured with 2-digit addresses numbers. The User
programming menu is structured with 1-digit address numbers.
Entrance in the manager menu is possible even when the system is armed, but there are
certain limitations, for example zones cannot be bypassed in armed mode.
Programming Confirm
Access menus 2- or 1-digit Submenu/
Code address Settings
Note: When programming a submenu, after confirmation you will return one step back –
when bypassing zones, programming access codes, association of areas, etc. When
programming a setting, like date, time and other, after confirmation you will return two
steps back to the main screen for entering address number.
5
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
2. SUPPORTED KEYBOARDS
According your system configuration you may use one of the following keyboard models:
Front view of ECLIPSE LED keyboards with open protective cover. The keyboards are
equipped with LED information display and rubber keypads for operation.
LCD 32 LCD 32 S
Front view of ECLIPSE LCD keyboards, where LCD 32 is with open protective cover. The
keyboards are equipped with LCD text display. LCD 32S is with sensitive buttons and
built-in card reader.
6
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
* Used in the previous design of keyboard models LED 8, LED 32, LCD 32 and LCD 32S,
as the button has the same functionality.
**Note: The functionality of BYPASS, TROUBLE and MEMORY buttons for LED8 and
LED16A keyboards is accessible through the manager and user menus only with the
same LED indication on the display.
7
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
2.4 Indication
Button/LED Color Description
* Used in the previous design of keyboard models LED 8, LED 32, LCD 32 and LCD 32S,
as the button has the same functionality.
** The indication applies only to LED keyboards
8
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
* Used in the previous design of the keyboard as the button has the same functionality.
9
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
2.6.2 Special indication for reviewing of address number (LED 8 and LED 16A)
With DISARM button the user can check the number of the current address
during manager or user programming.
You can use the button in the following way:
1. The symbols and are lighting on permanently together with a number of
zone(s), according the type of the programmed parameter. A blinking digit shows
that parameter which is in setting mode, and lighting on digit button shows the
current set value for this parameter.
2. To find out what is the number of the current ADDRESS, press the button.
The zone numbers 1 and 2 are lighting on, the zone 1 is blinking, and lighting on button
shows the first digit of the address number.
3. Press the right arrow button. The cursor will move one position on the right, zone 2
starts blinking and lighting on digit number shows the next number of the address.
4. Press the button again to step back in parameter setting mode.
Note: You can also leave the view mode and with single pressing the CANCEL button.
Recommendation: If you are not familiar in details with the programming menus write
down in sequence the digits (of lighting buttons) corresponding to the respective address
positions (zone numbers).
10
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Attention: If no action (pushing a button) is performed for 30 sec. after entering the
manager or user programming menu, the system automatically returns to the main screen
and is again in normal operation mode. Entrance in programming mode by a manager or
user is possible via more than one keyboard at the time even with the same code.
Three versions of the keyboard display are available according the supported language:
Cyrillic, Greek and EU version. Note: The type of the display is placed on the sticker on
the back of the keyboard: CYR (supports Cyrillic, English, Turkish fonts), GR (supports
English and Greek fonts) or EU (supports English, Hungarian, Italian and Portuguese
fonts) – see Appendix B.
11
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
3. OPERATION INSTRUCTIONS
3.1 Arming With a Keyboard
3.1.1 Full Arming Mode
Full Arm mode means that all zones in the armed areas are being protected. Full Arm can
be initialized after entering a valid user code or with quick access without code, when this
option is allowed in the menus for engineer programming.
Note: The button is used in the previous design of the keyboards.
12
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Exit Exit
Code
Time Time
Arming Push for 2-3
type seconds
• LED Keyboards
When the system is armed the numbers of the armed areas are lit in red.
At LED 8 keyboard, the DISARM button is off, and the quick button of the used arming
mode lights on in red.
At LED 16A and LED 32 keyboards, the used arming mode is checked after entering a
valid code and area number.
13
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
• LCD Keyboards
The status of the used areas is viewed with pressing of ENTER button. Note that the
“padlock” LED lights up in red only when all the used areas are armed. The “padlock” LED
lights up in green if at least one of the used areas is disarmed.
To check-up the areas status simple press the ENTER button:
The screen displays the area numbers with the current status for every one of them.
The description of the area status is as follows:
Status Description
- The area is disarmed and ready to be armed.
n The area is disarmed and not ready to be armed.
f The area is armed in FULL Arming Mode.
s The area is armed in STAY Arming Mode.
S The area is armed in SLEEP Arming Mode.
* Entry/ Exit time is running for the area.
A Alarm event in the area.
F Fire alarm in the area.
M Memory event in still armed area.
m Memory event in disarmed area.
Empty The area is not used in the system.
• LED Keyboards
The numbers of all open zones in the system are blinking. To review (filter) the zone
numbers associated to an area the User has to enter a valid code and area number. Only
the open zones for that area will proceed to blink and the area number is lighting on.
• LCD Keyboards
The numbers of all open zones in the system are displayed one-by-one on the LCD
screen. To review (filter) the zone numbers associated to an area the User has to enter a
valid code and area number. Only the open zones for that area will proceed to be
displayed as text messages.
The exit from the open zones review mode is with pressing CANCEL button or
automatically after 30 sec.
14
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Example: Areas 1-4 are in Full ARM mode, and 5-8 are in Sleep ARM mode. To change
the arming mode of area 5 do in sequence:
Code Area 5
Note: Use the button “0” to change all areas from one arming mode to another.
When using LCD keyboard, after the proxy card is recognized, the numbers of the areas
and their current status are shown on the display.
When using LED keyboard, after the proxy card is recognized the numbers of the areas
that are ready to be armed are blinking in green.
The system will wait for the number of areas to be entered.
Notes:
Use the button “0” to arm all associated to the user code areas.
The built-in card reader in LCD 32 Sensitive keyboard is situated in the right bottom
corner on the front panel and it is marked with a “key” pictogram.
15
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
• PR IT:
To arm the system in one of the listed above arming modes, the User has to
place and hold the proxy card in front of the stand-alone reader until activation
of the respective LED indication:
The reader beeps at every changing of the arming mode. When the LED indication of the
selected arming mode is on the User has to remove the card. After the exit time is over
the LED of the activated arming mode lights on permanently.
• Eclipse PR:
To arm the system in one of the listed above arming modes, the User
has to place the card in the area and wait until a confirmation signal is
heard. Remove the card and in a 5 seconds interval press a button for
arming:
Button ARMING
“Full Arming” – Lights on into red.
After the exit time is over the LED of the used arming mode is lighting on.
Button ARMING
Hold the button for 2-3 seconds to activate “Full Arming” for all areas.
According the programmed at address 21.
Note: Ask you installer for details about the arming modes set for your system.
16
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
3.3 Disarming
Every user can disarm only those areas associated for operation to its personal code.
Note: Certain users may not be permitted to disarm the system.
When using LCD keyboard, after the proxy card is recognized, the numbers of the areas
and their current status is shown on the display.
When using LED keyboard, after the proxy card is recognized the numbers of the armed
areas blink in red.
The system will wait for the number of the areas to be entered.
Sequence for disarming via card reader:
Notes: Use the button “0” to disarm all associated to the user code areas.
17
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Note: The user code must have assigned rights to operate with area where the alarm
event is triggered off the sirens.
To review the system troubles press the TROUBLE button. In TROUBLE MODE viewing
the TROUBLE button starts blinking. To exit TROUBLE MODE press CANCEL or wait 30
seconds for the system to leave this mode automatically.
For LED 8 and LED 16A keyboards the system troubles are indicated with permanently lit
TROUBLE LED. To review the system troubles single press the ENTER button.
The indication for system trouble will stop automatically after the trouble is restored.
The system troubles are displayed with permanently lit on number on the LED display and
with a text message on LCD displays. The text messages are displayed one by one or
can be scrolled manually with the arrows.
18
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
The indication for the technical troubles according the used keyboard is as follows:
Control panel
LED 32/ LCD 32 / Eclipse
LED 8 Description
LED 16A LCD 32 S
8 16 32
The mains power supply is
1. AC Loss
lost.
3. Blown
fuse
Blown out fuse.
Possible problems:
- Low battery charge of
10. WL
wireless device;
Button “2” device
- Wireless device lost;
trouble.
- Dirty chamber of a wireless
fire detector.
11. WL RF
Button “3” Radio signal jamming.
jamming.
Possible problems with power
supply of expander modules:
12. AUX - The mains power supply is
Button “4” PSU lost;
trouble. - Problem with the backup
battery;
- Blown out fuse.
19
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
20
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Main screen
After confirming the new code with the ENTER button, if the code is accepted, the
keyboard emits a confirmation beep and will return to code entry screen. If the entered
code is already being used in the system (a valid user or ambush code), the keyboard
emits a rejection beep. For LCD keyboards there is also “Invalid” message on the screen.
The system returns to address entry screen.
Going back to the main screen is done by pressing the CANCEL.
Note: Certain users may not be permitted to change their own code. In order for users to
be allowed to change their codes, option «4.Programming» at address 06 of the
manager programming menus needs to be allowed.
OR
Address
User Code User Code
The events are viewed in consecutive order, one by one, from the last to first with the help
of the arrow buttons.
On the screen of LCD keyboards a text message with the event type, consecutive number
starting from 0001 and date and hour are being displayed.
In case of using a LED keyboard to review the memory LOG file, keep in mind that the
visualization of the memory events, as the user numbers, zones numbers, area numbers
and etc., is presented in a binary form as the order is count from right to left side - see the
column “Code” of APPENDIX A, there is given the reference of the LED indication in
decimal form. The lit digits on the display form a code defining the event, which can be
checked in the Table of memory log events in the Appendix A. No information about the
date and time is available when using a LED keyboard.
By pushing button “2” additional information about the user, area, zone or device is being
displayed. Press the button “1” to return to the main display – see the examples in
Appendix A.
21
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
In case the user arms the system when the current active memory events are not
reviewed, the system event “Override Arm” is recorded in the memory log file.
Notes:
The memory log can be checked also when the system is armed after entering a valid
user code.
Checking the memory log with LED 8 and LED 16А keyboard is possible only by entering
address 2, because these keyboards do not have a MEMORY fast button.
The Chime signalization is a sound signal from the keyboards when opening an entry/ exit
type zone. The option can be enabled or disabled by the user. By default, the Chime
signalization is DISABLED.
To enable the Chime signalization the user first has to enter valid access code:
Address
User Code
Depending on the keyboard used, the visualization on screen is as follows:
Press the digit buttons or arrow buttons to change alternatively the status of the Chime.
LED 32
Press the digit buttons or arrow buttons to change alternatively the state of the Chime.
LED 8/ LED 16А
After entering the address 3, the digit buttons 1 to 9 are off – the Chime is disabled. Press
a random digit button or arrows to enable the Chime. The Chime is enabled when the
buttons from 1 to 9 are lighting on in red.
22
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
OR
Address
User Code Zone User Code Zone
Numbers Numbers
Note: Bypassing zones with LED 8 and LED16 keyboards is possible only by entering
address 4, because these keyboards do not have a BYPASS fast button.
Pushing the digit buttons or arrow buttons changes alternatively the state of the zone.
When the user chooses to bypass the zone, the BYPASS button is lit. When return to
normal operation mode, the BYPASS button is lit permanently on all keyboards.
LED 32
Pushing the digit buttons or arrow buttons changes alternatively the state of the zone.
When the user chooses to bypass a zone the BYPASS button is lit, while digits 1 to 8 of
the display are lit permanently. After going back to normal working mode the BYPASS
button is lit permanently on all keyboards.
LED 8/ LED 16А
Enter at the address 4 and choose a zone number for bypass – the LED for zone 1 is
blinking on the display. If the buttons 1 to 9 are off the zone is not bypassed; if the buttons
1 to 9 are lighting on in red – the zone is bypassed. To change the zone status, press a
random button or the arrows. The BYPASS LED is lit permanently.
23
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Important Notes:
The Chief Manager’s rights cannot be changed.
One Manager cannot change other Manager codes.
The Manager can change only regular User codes associated to common Area number(s)
with him.
24
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Main screen
Attention: In ECLIPSE 32 control panel you cannot create or change other Manager
codes, so before that go to address 06 and disable the 8.Manager right for the regular
users.
After confirming the new code with the ENTER button, if the code is accepted, the
keyboard emits a confirmation beep and goes back to the user number screen. If the
entered code is already being used in the system (a valid user or ambush code), the
keyboard emits a rejection beep. For LCD keyboards there is also “Invalid” message on
the screen. The system goes back to address entry screen.
To return to the main screen press the CANCEL button a few times.
OR
Address
Manager code Manager code
The events are viewed in consecutive order, one by one, from the last to first with the help
of the arrow buttons.
25
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
The Chime signalization is a sound signal from the keyboards when opening an entry/ exit
type zone. The option can be enabled or disabled by the manager. By default, the Chime
signalization is DISABLED.
To enable the Chime signalization the user first has to enter valid manager code:
Address
Manager Code
See item 4.3 for the visualization according the used keyboard.
OR
Address
Manager Zone Manager code Zone
code Numbers Numbers
Note: Bypassing zones with LED 8 and LED 16A keyboards is possible only by entering
address 04, because these keyboards do not have a BYPASS fast button.
See item 4.4 for the visualization according the used keyboard.
Note: Certain Managers may not be permitted to bypass zones. In order for users to
bypass zones option «3. Bypassing» at address 06 of the manager programming menus
needs to be allowed.
Address
Manager code
26
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Press the digit buttons or arrow buttons to change alternatively the state of the parameter.
LED 32
Press the digit buttons or arrow buttons to change alternatively the state of the parameter.
The engineer access is allowed when all digits from 1 to 8 are lit.
LED 8/ LED 16A
After entering the address 05, the digit buttons 1 to 9 are lighting on in red – the Engineer
access is enabled. Press a random digit button or arrows to disable. The Engineer access
is disabled when the buttons from 1 to 9 are off.
The choice is confirmed by pushing the ENTER button.
Address
Manager code User Assigning
number attributes
Attention:
User code 01 is Chief Manager and always has full access and assigned attributes which
cannot be changed or deleted! Option “8. Manager” is available for ECLIPSE 32 only!
Function of the user attributes:
1. Disarm The user code can disarm the system.
2. Stay and Sleep
The user code can arm the system in STAY and SLEEP mode.
Arm
3. Zone Bypass The user code can bypass zones in the protected site.
4. Programming The user code has access to the user programming menus.
5, 6 and 7 are not used
The user code has manager attributes in the system and has
8. MANAGER in access to the Manager programming menus.
the system Note: When attribute 8. Manager is set, attribute 4. Programming
also needs to be set!
27
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
By pressing the respective digit button the attribute is alternatively enabled or disabled.
The attribute is enabled when the digit is visualized on the screen. Disabled attributes are
marked with “*”.
LED 32
By pressing the respective digit button the attribute is alternatively enabled or disabled.
The attribute is enabled when the respective digit on the screen is lit.
LED 8/ LED 16A
Enter at the address 06 and choose a user number– the LED for zone 1 is blinking on the
display. The digit buttons corresponding to the assigned attributes are lighting on in red.
To disable an attribute press the respective number – the button is off, meaning the
attribute is disabled.
Note: If all attributes for a certain user code are disabled it does not get deleted from the
system and it can be used for FULL ARM, viewing the memory log and system troubles.
Associating areas to user codes is dome at address 07, after entering manager code:
Address
Manager code User Assigning area
number numbers
By default for User code 01 (Manager) are assigned for operation all area numbers.
28
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
By pressing the respective digit button the area is alternatively enabled or disabled. The
area is associated when the digit is visible on screen. When the area is not associated it is
market with the symbol “*”.
LED 32
Address
Manager code User Entering name
number
The letters are chosen by pressing the respective digit number until reaching the desired
letter. The cursor moves automatically after choosing a letter or number or manually with
the help of the arrow buttons. If you need to enter a number, the respective button is
pressed for 2-3 second – see also item 2.8.
29
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Associating timeslots to user codes is done at address 09, after entering manager code:
Address
Manager code User Number of
number timeslot
Time slot from 1 to 8 is assigned to the address. Only one time slot can be associated to
every user code.
Note:
If no time slot is associated to the code, the digit 0 is entered. This is the setting by
default.
Timeslots are associated by pressing the respective digit number. The number of the
chosen timeslot is visualized on screen.
LED 32
Timeslots(digit
are 10associated
is lit) by pressing the respective digit number. The number of the
chosen timeslot is lit permanently.
LED 8/ LED 16A
Enter at the address 09 and choose a user number - the LED for zone 1 is blinking on the
display. The digit button corresponding to the associated timeslot is lighting on in red. By
default the digit button 0 is on. To set other timeslot number you have to press the
corresponding digit button.
30
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Address
Manager code User Assigning
number attributes
Notes:
Only one arming mode can be used with every proxy card.
By default, all users are allowed to arm and disarm the system in SLEEP ARM mode.
The card can disarm and arm in The card can disarm and arm in
SLEEP ARM mode FULL ARM mode
31
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
LED 32
The card can disarm and arm in The card can disarm and arm in
SLEEP ARM mode FULL ARM mode
Address
Manager code User
number Put the card over
the reader*
The card is recognized on the LCD display and its 10-digit unique code is shown on
screen.
If the registration of a card to a user code is successful, after pushing the ENTER button,
a confirmation beep is heard. If the card is associated to a different user, an “Invalid”
message is shown on screen and a rejection signal is heard.
LED 32
32
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
The card is recognized on the LED display with digits 1 to 8 permanently lit.
If the registration of a card to a user code is successful, after pushing the ENTER button,
a confirmation beep is heard. If the card is associated to a different user, a rejection signal
is heard.
LED 8/ LED 16A
Enter at the address 11 and choose a user number - the LED for zone 1 is blinking on the
display. The registered user card is indicated with digit buttons 1 to 9 lighting on in red.
* Note:
The proxy reader can be a separate device or built in the keyboard (keyboards LED32
PR, LCD32 PR). The built in proxy reader is situated between the MEMORY, ENTER, “9”
and TROUBLES buttons.
In LCD 32S the card reader is situated in the right bottom corner and is indicated with a
“key” pictogram.
LED 32
Note:
No confirmation is necessary after deleting of a user card. You cannot reject the operation
with pressing the CANCEL button. To register the card again, follow the steps in item
5.12.
33
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
This is an address for copying (cloning) of attributes, rights, associations, time slots and
rights for work with proxy cards. The address allows the settings of one user code to be
copied to one or more users, which saves the need to program setting for every user
separately.
Cloning is done at address 13, after entering manager code:
Address
Manager code
Code numbers:
The cloning process starts by entering the number of the code that will be cloned
(“Source”). After that the number of the first code in the series of codes which will accept
the settings of the source is entered (First). In the end the last code in the series of codes
is entered (Last).
For example, if you want the settings of code 02 to be cloned to codes 03 to 10 you need
to enter: [02]> [03] [10].
If only one code is to accept the settings of the source, its number is entered both as
“First” and “Last” in the series.
LED 32
After entering address 13, digit 15 on the display blinks, while digit 16 is permanently lit –
the system indicates that it is expecting entering of “Source” code. After entering the first
digit of the code – digit 15 is lit permanently, while digit 16 blinks. The second digit of the
“Source” code is entered. The system now expects entering the “First” code, followed by
“Last” code. The indication is the same.
LED 8/ LED 16A
After entering address 13, digit 1 on the display blinks, while digits 2, 3, 4, 5 and 6 are
lighting up permanently – the system indicates that it is expecting entering in sequence of
“Source” code, “First” code and “Last” code. The set value at the respective position is
indicated with lighting up in red digit button.
For example, if the settings for code 02 have to be cloned for codes from 03 to 10, we
should enter in sequence: 020310.
34
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Address
Manager code Time
[HH: ММ]
Depending on the keyboard used, the visualization on screen is as follows:
LCD 32 and LCD 32 Sensitive
With the help of the digit buttons enter hour and minutes in the format [HH:ММ] – hour
from 00 to 23 and minutes from 00 tо 59.
LED 32
After entering address 14, digit 15 on the display blinks, while 16 is lit permanently – the
system indicates that it expects entering an hour from 00 to 23. Enter the current hour.
After entering the first digit, on the display 15 is lit permanently, while 16 blinks. After the
second digit is entered, 15 blinks again, while 16 is lit permanently – the system indicates
that it expects entering minutes from 00 to 59. The indication is the same.
LED 8/ LED 16A
After entering address 14, digit 1 on the display blinks, while 2, 3 and 4 are lit permanently
– the system indicates that it expects entering the new time in the format [HH:ММ] – hour
from 00 to 23 and minutes from 00 tо 59. Enter in sequence the new time. You can review
the entered time using the arrow buttons – the set value at the respective position is
indicated with a lit on in red digit button.
The entered time is confirmed by pressing the ENTER button.
Address
Manager code Date
[DD/ММ/YY]
With the help of the digit buttons, enter the date in the format [DD/ММ/YY] – day, month,
and year.
35
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
LED 32
After entering address 15, on the display 15 blinks, while 16 is lit permanently – the
system indicates that it expects entering a day from 01 to 31. Enter the day. After entering
the first digit on the display 15 is lit permanently, while 16 is blinking. After entering the
second digit of the day 15 blinks again, while 16 is lit permanently – the system indicates
that it expects entering a month from 01 to 12. The indication is the same. Only the last
two digits of the year are entered.
LED 8/ LED 16A
After entering address 15, on the display 1 blinks, while 2, 3, 4, 5 and 6 are permanently
lit – the system indicates that it expects entering of a new date in format [DD/ММ/YY].
Enter in sequence the new date. You can review the entered date using the arrow buttons
– the set value at the respective position is indicated with a lit on in red digit button.
The entered date is confirmed by pushing the ENTER button.
Address
Manager code Number from
000 to 255
Depending on the keyboard used, the visualization on screen is as follows:
LCD 32 and LCD 32 Sensitive
With the help of the digit buttons enter the number of allowed incorrect codes.
LED 32
After entering address 16, on the display 14 blinks, while 15 and 16 are lit permanently –
the system indicates that it expects entering a number for allowed incorrect codes from
000 to 255. After entering the first digit on the display 14 and 16 are lit permanently, while
1 blinks. After entering the second digit on the display 14 and 15 are lit permanently, while
16 blinks. All 3 digits need to be entered.
36
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Address
Manager code Assigning
rights
Remote access rights:
1. REMOTE DISARM Allows remote disarm
2. REMOTE ARM Allows remote arm.
3. REMOTE CODES ACCESS Allows remote change of user codes.
4. REMOTE PROGRAMMING Allows remote programming of the system.
6. REMOTE ZONE BYPASS Allows remote zone bypass.
By default all attributes are enabled.
37
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Address
Manager code
The communicator will start an automatic sending of messages – firstly towards the
monitoring station (if there are phone numbers entered in the digital communicator) and
afterwards via the voice dialer (if there is such fitted and there are phone numbers
entered). The programming menu can be exit by pushing the CANCEL button.
Address
Manager code User Function
number number
38
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Note:
The sound level cannot be muted or disabled.
39
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
40
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Address Backlight on
Manager code
Backlight off
When the backlight is off, the buttons are lit only when they are pressed.
LED Event
Code Description
Indication number
1 1 Burglary Alarm event
2 2 Burglary Alarm event restore
3 3 Fire Alarm event
4 4 Fire Alarm event restore
5 5 Panic Alarm event
6 6 Panic Alarm event restore
7 7 Tamper Alarm event
8 8 Tamper Alarm event restore
9 9 Medical Alarm event
41
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
42
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
43
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
44
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Note: The symbols for codes from 032 to 122 are same for all keyboard display versions.
45
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
46
ECLIPSE 8/ 16/ 32 Series – User Operation Manual
Zones Description
Zone Type Zone Type Zone Type
1 12 23
2 13 24
3 14 25
4 15 26
5 16 27
6 17 28
7 18 29
8 19 30
9 20 31
10 21 32
11 22
PGMs Description
PGM 1 PGM 3 PGM 5
PGM 2 PGM 4
System Timers
Entry time, (sec.)
Exit time, (sec.)
The siren will be activated, (min.)
Installer: .......................................................................................................
Service: ........................................................................................................
Tel./Fax: .......................................................................................................
47
www.teletek-electronics.com