10 37 00 1110 NS 1 A4 Watermarked
10 37 00 1110 NS 1 A4 Watermarked
Once printed this specification becomes an uncontrolled copy of the online version.
10.37.00.1110
NS-1™ Number: NS 10.37.00.1110
Revision Date: June 2007
Equipment Name: SIDE POCKET MANDRELS ROUND AND OVAL WELDED ASSEMBLIES
Manufacturer: GENERAL
Model/Type: INTEGRAL FORGED AND WELDED SWAGE ENDS
Material Group: LOW ALLOY STEEL
Service: NON-SOUR
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 1
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
SCOPE
This GENERAL NS-1™ specifies the minimum quality and inspection requirements applied to wrought Low Alloy
Steel Side Pocket Mandrels, Round and Oval Welded Assemblies, Types – Integral Forged and Welded Swage Ends.
It applies to:
Design verification, approval and other design related parameters are specifically excluded from this NS-1™.
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 2
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
SUPPLEMENTARY REQUIREMENTS
The following requirements are supplementary to, and shall be applied in conjunction with, the Quality Sub-
specifications of this NS-1™ specification:
1. WELDING
(Ref. Sub-Spec. 30.1)
In addition to the testing requirements of ASME Section IX Article I, the weld Procedure Qualification Record
(PQR) shall include hardness testing as defined in Welding Requirements section as detailed in API Specification
16A.
2. MATERIAL TESTING
(Ref. Sub-Spec. 10.1 & Sub-Spec. 10.4)
Chemical analysis shall be carried out on a heat basis, demonstrating conformance to the
manufacturer’s applicable material specification for all elements contained therein.
Mechanical testing to ASTM A370 shall, as a minimum, establish yield strength, tensile strength,
elongation and reduction in area on a heat basis, representative of any heat treatment that may have
been applied.
3. HYDROSTATIC TESTING
(Ref. Sub-Spec. 100.2)
The timing of the holding periods shall not start until the test pressure has stabilized, the equipment and measuring
devices have been isolated from the pressure source and the external surfaces of the Mandrel thoroughly dried.
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 3
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
Collapse pressure testing shall be performed on "Oval Type" Mandrels. Five percent (5%) of the
order quantity with a minimum of one (1) mandrel per order shall be tested.
The hydrostatic test pressure shall be calculated by applying a fibre stress value of at least 80% of
the specified minimum yield strength.
Where the test pressure is limited by the threaded end connections, it shall be calculated using the
following formula:
P = (2 . f . Yp . t) / D
Where:
P = hydrostatic test pressure, in (MPa)
f = a factor of 0.8 of specified minimum yield strength
Yp = specified yield strength for the pipe body (MPa)
t = nominal design wall thickness adjacent to thread connection (mm)
D = nominal outside diameter of the connecting thread (mm)
As a minimum, the hydrostatic test pressure shall not be less than the equipment rated working
pressure.
4. FUNCTIONAL TESTING
Functional testing shall be carried out to the manufacturer’s specification but shall include the following steps as
a minimum:
Each mandrel shall be externally drifted using a full length cylindrical sleeve of a suitable drift
diameter, or alternatively overall straightness/O.D. measurements shall be carried out to verify
conformance to design requirements.
Each mandrel shall be internally drifted using a cylindrical drift bar that exceeds the length of the
mandrel. Drift bar diameter shall be as specified in ISO 11960, unless otherwise specified in the
purchase order.
Each mandrel valve pocket shall be drifted using either a dummy valve designed for drifting
(combined with Hydro-testing) or a separate pocket drift bar.
A gauge cutter shall be passed through each mandrel with the mandrel in horizontal position and the
pocket in the lowest position. No "hold- ups" are accepted.
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 4
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
A (dummy) valve installation and retrieval test shall be carried out on each mandrel using the
appropriate setting and retrieval tools (i.e. identical to those used in service). This test shall be
carried out with the mandrel in the horizontal plane and the valve pocket in the top position.
Torque testing to a minimum of 1,360 N.m (1,000 ft.lbf) shall be carried out on welded orientation
sleeves (i.e. not required on integral sleeves). The torque loading shall be applied for a minimum of
15 seconds. Any movement shall be cause for rejection. Where possible the sleeve weld(s) shall be
visually checked for cracks following this test. Detection of any cracks shall be cause for rejection.
The above functional tests shall be carried out after all hydro-testing has been completed.
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 5
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
MATRIX
Equipment Name: Side Pocket Mandrels Round and Oval Welded Assembly
Specification: 10.37.00.1110
Manufacturer: General
Model/Type: Various
Material Group: Low Alloy
Service: Non-Sour
Body Members
Class: A, B, D Material: Wrought Low Alloy Steel
Number Title
10.1 Material Certificates – General
10.4 Type B Material Test Certificate
20.2 Traceability – Heat Traceability
90.1 Dimensional Inspection – General
160.1 Non-Conformity Procedure – General
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 6
Quality and Inspection Requirements for New and Refurbished Drilling and Well Completion Equipment
Once printed this specification becomes an uncontrolled copy of the online version.
Fillet/Spot Welds
Class: E
Number Title
30.1 Welding Qualifications – General
40.1 NDE Surface, General
40.13.1 Liquid Penetrant (PT) and Visual (VE) Examination of Welds – Technique
40.13.2.3 Liquid Penetrant (PT) and Visual (VE) Examination of Welds – Required Extent -One Hundred
Percent
40.13.3 Liquid Penetrant (PT) and Visual (VE) Examination of Welds – Acceptance Standard
60.1 Disposition of Defects – Surface Dressing
60.3 Disposition of Defects – Repair of Weld Defects
160.1 Non-Conformity Procedure – General
Complete Assembly
Number Title
10.1 Material Certificates – General
10.2.2 Material Certificates – Assembly Certificate
20.3 Traceability – Serialization Traceability
40.1 NDE Surface, General
40.10.1 Liquid Penetrant Examination (PT) of Forgings, Mech. Tubing & Barstock – Technique
40.10.2.3 Liquid Penetrant Examination (PT) of Forgings, Mech. Tubing & Barstock – Required Extent –
One Hundred Percent
40.10.3.5 Liquid Penetrant Examination (PT) of Forgings, Mech. Tubing & Barstock – Acceptance Standard
– Maximum Permitted Relevant Indication
40.12.1 Liquid Penetrant and Visual Examination (PT + VE) of Threads – Technique
40.12.2.3 Liquid Penetrant and Visual Examination (PT + VE) of Threads – Required Extent -One Hundred
Percent
40.12.3.2 Liquid Penetrant and Visual Examination (PT + VE) of Threads – Acceptance Standard -Relevant
Indications
60.1 Disposition of Defects – Surface Dressing
90.1 Dimensional Inspection – General
90.2 Dimensional Inspection – Threads
100.2 Hydrostatic Testing – General
130.1 Functional Testing – General
160.1 Non-Conformity Procedure – General
170.1 Boxing/Packing/Marking – General
170.2 Boxing/Packing/Marking – Critical Service (H2 S, CO2 , Low Temperature)
180.1.2 Documentation Package – Quality Documentation – Full
Photocopying or reproducing this page in any way constitutes as infringement of the license agreement
for the continued supply of the NS-1™ Service
NS 1 Page 7