Swagelok - Tube Fitting
Swagelok - Tube Fitting
Swagelok - Tube Fitting
www.swagelok.com
FITTINGS
TUBE
Gauge able Tube Fit tings
and Adapte r Fit tings
Features
FITTINGS
TUBE
Back ferrule
Hinge point
Nut
Tubing
Front ferrule
Fitting body
Contents
FITTINGS
TUBE
Features, 2 Straight Fittings Weld Connectors
Reducing Union,
Compliance with Industry
15
Standards, 7
Male Pipe, 25
Materials, 8
Bulkhead Union
and Bulkhead
O-Rings, 8
Reducing Female Connectors
Union, 16
Cleaning and NPT, 26
Packaging, 8
ISO/BSP Tapered
Male Connectors Thread (RT),
Metric Swagelok Tube
ISO/BSP Parallel
Fittings, 9 NPT, 17 Thread (RJ and
ISO/BSP Tapered RP), 27
Pressure Rating Basis and
Thread (RT), 18
Thread Specifications, 9 ISO/BSP Parallel
ISO/BSP Parallel Thread (RG,
Pressure Ratings, 10 Thread (RS), 19 Gauge), 28
ISO/BSP Parallel
Ordering Numbers and Thread (RP), 20
Dimensions, 14 Bulkhead
NPT, 28
Bulkhead
NPT, 21
Reducers
SAE/MS
Straight Thread Reducer, 29
(ST) and Long Long Reducer,
SAE/MS Straight 30
Thread (ST), 21
Additional Products
O-Seal (SAE/MS Bulkhead
■ For Alloy 2507 super duplex
Straight Thread Reducer, 30
tube fittings, refer to Gaugeable
Alloy 2507 Super Duplex Tube and NPT), 22
Fittings catalog, MS‑01‑174.
■ For alloy 400 tube fittings, refer AN and
to Gaugeable Alloy 400/R‑405
Port Connectors
AN Bulkhead
Mechanically Attached Pipe Fitting, 23 Port Connector
and Tube Fittings catalog,
and Reducing
MS‑02‑332.
10-32 Thread, Port Connector,
■ For PFA tube fittings, refer to
M5 × 0.8 Thread, 31
PFA Tube Fittings catalog,
MS‑01‑05. and Metric
■ For medium- and high-pressure Thread (RS), 24
tube fittings, refer to Medium-
and High-Pressure Fittings,
Tubing, Valves, and Accessories
catalog, MS-02-472.
4 Tube Fittings
Contents
FITTINGS
TUBE
Plug, 32
Positionable, Application-Specific Fittings
SAE/MS Straight
Thread (ST), 39 Kwik-Clamp Flange
Vent Protectors
to Swagelok Tube
Fitting, 47
Mud Dauber, 32
Tees
Orifice Plate Fitting,
Unions
48
90° Elbows
Union and Reducing Bored-Through Fittings
Unions Union, 40
For thermocouples, dip tubes, and heat
exchanger tees, 20
Union, 33
Male
Tube Adapters
Branch, NPT (TTM) and Tube Adapter Information, 49
Male
Adapter Tees, 42
NPT, 34 Male
ISO/BSP Tapered
Run, NPT (TMT), 43 NPT and ISO/BSP
Thread (RT), 35
Tapered Thread (RT),
50
Reducing Elbow, Positionable Branch,
36 SAE/MS Straight ISO/BSP Parallel
Thread (TTS) and Thread (RS and RP),
Positionable, ISO/BSP Positionable Branch, 51
Parallel Thread (PR) ISO/BSP Parallel
and Positionable, Thread (TTR), 44
SAE/MS Straight
SAE/MS Straight
Positionable Run, Thread (ST) and O-Seal
Thread (ST), 37
SAE/MS Straight (SAE/MS Straight
Thread (TST), 44 Thread), 52
Weld
Positionable Run,
Tube Socket, 38 ISO/BSP Parallel AN Thread, 52
Thread (TRT), 45
Female
Male Pipe, 38
Pipe Weld, 53
Run, NPT (TFT), 45
Female
Branch, NPT (TTF),
NPT, 38 46
Gaugeable Tube Fittings and Adapter Fittings 5
Contents
FITTINGS
TUBE
Female ISO/BSP Parallel Gaskets Gaugeability, 69
PT and ISO/BSP
N Steel (RS Fitting),
Tapered Thread Copper (RP Fitting), Installation Instructions, 69
(RT), 53 Copper (RG, Gauge
Swagelok Tube Fittings, 70
Fitting), and PTFE
ISO/BSP Parallel (RJ Fitting), 60 O-Seal Male Connectors, 70
Thread (RP and RJ),
and ISO/BSP O-Rings Caps and Plugs, 71
Parallel Thread (RG, Buna N (O-Seal Port Connectors, 71
Gauge), 54 Straight Threads
and O-Seal Pipe Positionable Elbows and Tees, 72
Threads) and Tube Adapters, 72
Fluorocarbon FKM
AN Thread, 54 AN Thread Swivel Nut, 72
(ISO/BSP Parallel
Threads and Weld Fittings, 73
SAE/MS Straight
Threads), 61 Depth Marking Tool, 73
Additional Ordering
Preswaging Tool, 73
Information, 55 Tools and Accessories
Hydraulic Swaging Units, 62
Replacement Parts Chromatograph Fittings
Nuts Refer to Gaugeable
Chromatograph and
Column End Fittings
Female, 57 catalog, MS-02-173.
Dielectric Fittings
Preswaging Tools, 65
Refer to Dielectric
Fittings catalog,
Knurled Female, 57 MS‑02‑36‑SCS.
Wrenches, 66
Flanges
Gap Inspection For ANSI, DIN, and JIS
Gauges and Depth flanges, refer to Flange
Male, 57
Marking Tools, 67 Adapters catalog,
MS-02-200.
Bulkhead Retainers,
Ferrules 68
VCO® and VCR®
Face Seal Fittings
Front, 58 Refer to VCR Metal
Inserts for Soft Gasket Face Seal
Plastic Tubing, 68 Fittings catalog,
MS-01-24 and VCO
O-Rings Face Seal
Back, 58 For liquid leak detectors, lubricants, Fittings catalog
and sealants, refer to Leak Detectors, MS‑01‑28.
Nut-Ferrule Set and Lubricants, and Sealants catalog,
Package and MS‑01‑91.
Ferrule Set and
For tube benders and tube preparation
Ferrule-Pak™
tools, refer to Tubing Tools and
Package, 59
Accessories catalog, MS-01-179.
6 Tube Fittings
FITTINGS
TUBE
design compensates for changes in repeatable installation.
■ TÜV SUD Automotive
temperature during system start-up ■ DVGW Swagelok authorized sales and service
and shutdown and helps eliminate centers offer installation training
■ Department of the Navy (U.S.)
leakage related to rapid thermal seminars that provide additional
■ Det Norske Veritas (DNV)
expansion or contraction. information on:
■ Nippon Kaiji Kyokai (NK)
Swagelok has conducted tests ■ The requirements for making safe,
■ American Bureau of Shipping (ABS) leak-tight connections
that demonstrated the capability of
Swagelok tube fittings to withstand ■ Lloyd’s Register of Shipping (LR) ■ A variety of tools and accessories
thermal shock and high temperature. ■ Bureau Veritas (BV) designed for use with Swagelok tube
Contact your authorized Swagelok ■ RS Maritime fittings.
representative for more information ■ Canadian Provincial Agencies (CRN)
about thermal shock test reports. Corrosion
■ Russian GOST TR (Customs Union
Countries) Swagelok tube fittings are available
Compliance with in a variety of materials, including
■ UkSepro for Ukraine
Industry Standards optimized 316 stainless steel chemistry
■ Inspecta Nuclear for Sweden
Swagelok Company works with with elevated nickel, chromium, and
■ METI/KHK other elements for superior corrosion
standards organizations around the
world to provide you with products that ■ Engineers India Limited (EIL) resistance in a variety of applications,
address your needs. For a complete listing, refer to the including chemical processing, sour
Stainless steel Swagelok tube fittings Tube Fitting Performance Product Test gas and subsea systems.
used with 316 stainless steel and 316 Ti Reports PTRs and Third-Party Product Swagelok has conducted tests in
stainless steel alloy tubing as shown Approvals and Registrations, accordance with ASTM B117-95 to
in the table have been tested to the MS-06-108. evaluate the corrosion resistance of
requirements of ECE R110. In addition, Swagelok tube fittings.
See Materials, page 8; Thread
stainless steel Swagelok tube fittings
are available with EC-79 certification. Specifications, page 9; and Contact your authorized Swagelok
Pressure Ratings, page 9, for more representative for more information
Tube OD Wall Thickness information about the specifications about corrosion resistance test reports.
3 to 16 mm 0.7 to 2.5 mm to which Swagelok tube fittings are
1/8 to 5/8 in. 0.028 to 0.095 in. manufactured. Intermix/Interchange
Contact your authorized Swagelok This practice can be dangerous.
NACE - Sour Gas representative for more information Leak-tight seals that will withstand
about Swagelok tube fitting high pressure, vibration, vacuum,
Swagelok offers fittings in materials
that meet metallurgical requirements of certifications. and temperature changes depend
NACE MR0175/ISO 15156 and MR0103. on close tolerances and consistent,
Installation exacting quality control in conjunction
NORSOK The Swagelok tube fitting installation with good design principles. The
Swagelok offers fittings in materials that advantages: critical interaction of precision parts is
are compliant with M650. essential for reliability and safety.
■ Easy to install
Contact your authorized sales and service Components of other manufacturers
■ No torque is transmitted to tubing
representative for additional details. may look like Swagelok tube fitting
during installation
components—but they cannot be
■ Swagelok gap inspection gauge
manufactured in accordance with
assures sufficient pull-up upon initial Swagelok engineering standards, nor
installation. do they benefit from innovations in
Swagelok tube fitting components design and precision manufacturing
provide exceptional dimensional, defined by more than 45 Swagelok
tube fitting patents issued since 1989.
8 Tube Fittings
Materials O-Rings
O-seal fittings include a 70 durometer Buna N O-ring. Other
FITTINGS
Materials Standards
TUBE
FITTINGS
TUBE
Shaped fittings, such as elbows, crosses, and tees, are tapered threads. SWAK™ anaerobic pipe thread sealant and
stamped MM for metric tubing and have no step on the forging. Swagelok PTFE tape are available. Refer to Leak Detectors,
Lubricants, and Sealants catalog, MS-01-91, for additional
Swagelok Swagelok Swagelok information.
metric fractional metric tube
tube end tube stub ends
Port Connectors, Reducers, and Tube
Adapters
Swagelok tube adapters with the machined groove are
rated to the highest suggested allowable working pressure,
Stepped identification No shoulder Stepped identification see Swagelok Tubing Data, MS-01-107 for a tube outside
shoulders shoulders diameter and material in question.
ASME B31.3, Process Piping or pressure testing with a 4:1 ASME B1.20.1,
NPT NPT
design factor based on hydraulic fluid. leakage. SAE AS71051
ISO/BSP (tapered) ASME B31.3, Process Piping or pressure testing with a 4:1 ISO/BSP (tapered) ISO 7, BS EN 10226-1,
(Swagelok RT fittings) design factor based on hydraulic fluid. leakage. Swagelok RT fittings JIS B0203
ISO 1179-4, ISO 228-1 Threads with Stud Ends for general use ISO/BSP (parallel)
ISO/BSP (parallel) ISO 228,
only with metal-to-metal sealing (type B) or pressure testing Swagelok RP and RS
(Swagelok RP fittings) JIS B0202
with a 4:1 design factor based on hydraulic fluid leakage. fittings
Pressure Ratings
FITTINGS
Ratings are based on ASME Code for Pressure Piping B31.3, Process Piping, at ambient temperature.
316 SS, Carbon
Steel, Alloy (600, Brass and Alloy 2507 and
and C-276) Aluminum Alloy 400 Titanium Alloy 625 6-Moly Alloy 825
NPT/ISO Male Female Male Female Male Female Male Female Male Female Male Female Male Female
Pipe Size psig psig psig psig psig psig psig psig psig psig psig psig psig psig
in. (bar) (bar) (bar) (bar) (bar) (bar) (bar) (bar) (bar) (bar) (bar) (bar) (bar) (bar)
11 000 6 700 5 500 3 300 9 900 6 000 8 800 5 300 15 000 12 900 14 900 9 000 12 800 7800
1/16
(757) (461) (378) (227) (682) (413) (606) (365) (1 033) (888) (1 026) (620) (881) (537)
10 000 6 500 5 000 3 200 9 000 5 800 8 000 5 200 15 000 12 500 13 500 8 800 11 600 7500
1/8
(689) (447) (344) (220) (620) (399) (551) (358) (1 033) (861) (930) (606) (799) (516)
8 000 6 600 4 000 3 300 7 200 5 900 6 400 5 200 15 000 12 700 10 800 8 900 9 300 7600
1/4
(551) (454) (275) (227) (496) (406) (440) (358) (1 033) (875) (744) (613) (640) (523)
7 800 5 300 3 900 2 600 7 000 4 700 6 200 4 200 15 000 10 200 10 500 7 100 9 000 6100
3/8
(537) (365) (268) (179) (482) (323) (427) (289) (1 033) (702) (723) (489) (620) (420)
7 700 4 900 3 800 2 400 6 900 4 400 6 100 3 900 14 800 9 400 10 400 6 600 8 900 5700
1/2
(530) (337) (261) (165) (475) (303) (420) (268) (1 019) (647) (716) (454) (613) (392)
7 300 4 600 3 600 2 300 6 500 4 100 5 800 3 600 10 000 8 900 9 800 6 200 8 500 5300
3/4
(502) (316) (248) (158) (447) (282) (399) (248) (689) (613) (675) (427) (585) (365)
5 300 4 400 2 600 2 200 4 700 3 900 4 200 3 500 10 000 8 500 7 100 5 900 6 100 5100
1
(365) (303) (179) (151) (323) (268) (289) (241) (689) (585) (489) (406) (420) (351)
6 000 5 000 3 000 2 500 5 400 4 500 4 800 4 000 10 000 9 600 8 100 6 700 6 900 5800
1 1/4
(413) (344) (206) (172) (372) (310) (330) (275) (689) (661) (558) (461) (475) (399)
5 000 4 600 2 500 2 300 4 500 4 100 4 000 3 600 9 600 8 900 6 700 6 200 5 800 5300
1 1/2
(344) (316) (172) (158) (310) (282) (275) (248) (661) (613) (461) (427) (399) (365)
3 900 3 900 1 900 1 900 3 500 3 500 3 100 3 100 7 500 7 500 5 200 5 200 4 500 4500
2
(268) (268) (130) (130) (241) (241) (213) (213) (516) (516) (358) (358) (310) (310)
Pressure Ratings
STH SAE/MS Heavy Duty Pressure Ratings
FITTINGS
TUBE
Pressure ratings are based on SAE J1926/2 at ambient temperature.
316 SS, Carbon Steel, and
Alloy (C-276, 2507, 625,
6-Moly, 825, and 600) Brass and Aluminum Alloy 400 Titanium
STH
Non- Non- Non- Non-
SAE/MS
positionable Positionable positionable Positionable positionable Positionable positionable Positionable
Thread
Size Designator psig (bar) psig (bar) psig (bar) psig (bar) psig (bar) psig (bar) psig (bar) psig (bar)
3/8-24 3STH
7/16-20 4STH
1/2-20 5STH
9137 (630) 4568 (315) 8223 (567) 7309 (504)
9/16-18 6STH
6091 (420) 3045 (210) 5482 (378) 4873 (336)
3/4-16 8STH
7/8-14 10STH
1 1/16-12 12STH
1 3/16-12 14STH 6091 (420) 3045 (210) 5482 (378) 4873 (336)
1 5/16-12 16STH 5076 (350) 2538 (175) 4568 (315) 4061 (280)
1 5/8-12 20STH 4061 (280) 2030 (140) 3654 (252) 3248 (224)
4061 (280) 2030 (140) 3654 (252) 3248 (224)
1 7/8-12 24STH
3045 (210) 1522 (105) 2741 (189) 2436 (168)
2 1/2-12 32STH 2610 (180) 1305 (90) 2349 (162) 2088 (144)
Pressure Ratings
FITTINGS
Pressure ratings are at ambient temperature and apply to slide-on and crimped-on swivel nuts with a female gland.
316 SS, Carbon
Steel, and
Alloy (C-276,
2507, 625, 6-Moly, Brass and
825, and 600) Carbon Steel Aluminum Alloy 400 Titanium
Male AN Straight Shape Straight Shape Straight Shape Straight Shape Straight Shape
(JIC) psig psig psig psig psig psig psig psig psig psig
Thread Size Designator (bar) (bar) (bar) (bar) (bar) (bar) (bar) (bar) (bar) (bar)
10 000 10 000 4 500 4 500 5 000 5 000 9 000 9 000 8 000 8 000
7/16-20 4AN
(689) (689) (310) (310) (345) (345) (620) (620) (551) (551)
9/16-18 6AN
8 200 7 600 4 000 4 000 4 100 3 800 7 380 6 840 6 560 6 080
(564) (523) (275) (275) (282) (262) (508) (471) (452) (410)
3/4-16 8AN
7 000 6 300 3 000 3 000 3 500 3 150 6 300 5 670 5 600 5 040
1 1/16-12 12AN
(482) (434) (210) (210) (241) (217) (434) (391) (386) (347)
5 000 4 100 2 500 2 500 2 500 2 050 4 500 3 690 4 000 3 280
1 5/16-12 16AN
(344) (282) (170) (170) (172) (141) (310) (254) (276) (226)
2 000 2 000 2 000 2 000 1 000 1 000 1 800 1 800 1 600 1 600
1 5/8-12 20AN
(140) (140) (140) (140) (69) (69) (124) (124) (110) (110)
1 500 1 500 1 500 1 500 700 750 1 350 1 350 1 200 1 200
1 7/8-12 24AN
(105) (105) (105) (105) (48) (52) (93) (93) (83) (83)
1 125 1 125 1 125 1 125 500 560 1 010 1 010 900 900
2 1/2-12 32AN
(80) (80) (80) (80) (34) (39) (70) (70) (62) (62)
Pressure Ratings
FITTINGS
TUBE
ISO 228/BSP Parallel Thread (RS and RP)
Pressure Ratings
Hydraulic pressure ratings are based on ISO 1179 at ambient
temperature.
■ RS and RP male connectors were tested with RP female
connectors.
■ RS end connections were tested with bonded RS gaskets.
■ RP connections were tested without a gasket.
■ Gasket selection is the responsibility of the system
designer and user and may affect product performance.
■ Dimensions are for reference only and are subject to change. Unless noted otherwise, dimensions shown are for stainless
steel components and with Swagelok nuts finger-tight. For Swagelok nut dimensions, see page 57.
■ CAD templates are available on www.swagelok.com.
Straight Fittings
Unions
F flat
Tx
D E D D E Dx
A A
Straight Fittings
FITTINGS
Unions Reducing Union
TUBE
Basic
Tx Tube OD Dimensions
Ordering
T T Tx Number A D Dx E
Dimensions, in.
D E Dx
1/8 1/16 -200-6-1 1.22 0.50 0.34 0.05
A 1/16 -300-6-1 1.27 0.34 0.05
3/16 0.54
1/8 -300-6-2 1.44 0.50 0.09
1/16 -400-6-1 1.35 0.34 0.05
1/4 1/8 -400-6-2 1.52 0.60 0.50 0.09
3/16 -400-6-3 1.55 0.54 0.12
1/8 -500-6-2 1.56 0.50 0.09
5/16 0.64
1/4 -500-6-4 1.66 0.60 0.19
1/16 -600-6-1 1.44 0.34 0.05
1/8 -600-6-2 1.61 0.50 0.09
3/8 0.66
1/4 -600-6-4 1.70 0.60 0.19
5/16 -600-6-5 1.74 0.64 0.25
1/8 -810-6-2 1.78 0.50 0.09
1/2 1/4 -810-6-4 1.85 0.90 0.60 0.19
3/8 -810-6-6 1.91 0.66 0.28
3/8 -1010-6-6 1.94 0.66 0.28
5/8 0.96
1/2 -1010-6-8 2.05 0.90 0.41
1/4 -1210-6-4 1.94 0.60 0.19
3/8 -1210-6-6 2.00 0.66 0.28
3/4 0.96
1/2 -1210-6-8 2.11 0.90 0.41
5/8 -1210-6-10 2.11 0.96 0.50
1/2 -1610-6-8 0.90 0.41
1 2.38 1.23
3/4 -1610-6-12 0.96 0.62
Dimensions, mm
3 2 -3M0-6-2M 35.3 12.9 12.9 1.7
2 -6M0-6-2M 38.6 12.9 1.7
6 3 -6M0-6-3M 38.6 15.3 12.9 2.4
4 -6M0-6-4M 39.4 13.7 2.4
8 6 -8M0-6-6M 42.3 16.2 15.3 4.8
6 -10M0-6-6M 44.5 15.3 4.8
10 17.2
8 -10M0-6-8M 45.1 16.2 6.4
6 -12M0-6-6M 47.0 15.3 4.8
12 8 -12M0-6-8M 47.8 22.8 16.2 6.4
10 -12M0-6-10M 48.7 17.2 7.9
14 12 -14M0-6-12M 48.8 24.4 22.8 6.4
15 12 -15M0-6-12M 48.8 24.4 22.8 6.4
10 -16M0-6-10M 49.5 17.2 7.9
16 24.4
12 -16M0-6-12M 52.0 22.8 9.5
18 12 -18M0-6-12M 53.5 24.4 22.8 9.5
18 -25M0-6-18M 61.0 24.4 15.1
25 31.3
20 -25M0-6-20M 62.3 26.0 15.9
18 -30M0-6-18M 75.4 24.4 15.1
30 20 -30M0-6-20M 75.4 39.6 26.0 15.9
25 -30M0-6-25M 80.1 31.3 21.8
18 -32M0-6-18M 77.8 24.4 15.1
32 20 -32M0-6-20M 77.8 42.0 26.0 15.9
25 -32M0-6-25M 82.3 31.3 21.8
20 -38M0-6-20M 87.5 26.0 15.9
38 25 -38M0-6-25M 92.0 49.4 31.3 21.8
30 -38M0-6-30M 105 39.6 26.2
Straight Fittings
FITTINGS
F flat F flat
Dimensions
Basic Panel Max
Tube Ordering Hole Panel
OD Number A D E F Size Thickness
D D Dimensions, in.
E
A 1/16 -100-61 1.24 0.34 0.05 5/16 13/64 0.12➀
1/8 -200-61 2.02 0.50 0.09 1/2 21/64
0.50
3/16 -300-61 2.11 0.54 0.12 9/16 25/64
1/4 -400-61 2.27 0.60 0.19 5/8 29/64 0.40
5/16 -500-61 2.39 0.64 0.25 11/16 33/64
0.44
3/8 -600-61 2.45 0.66 0.28 3/4 37/64
1/2 -810-61 2.80 0.90 0.41 15/16 49/64
0.50
5/8 -1010-61 2.86 0.96 0.50 1 1/16 57/64
3/4 -1210-61 3.11 0.96 0.62 1 3/16 1 1/64 0.66
1 -1610-61 3.77 1.23 0.88 1 5/8 1 21/64
1 1/4 -2000-61 4.85 1.62 1.09 1 7/8 1 41/64
0.75
1 1/2 -2400-61 5.48 1.97 1.34 2 1/4 1 61/64
2 -3200-61 7.10 2.66 1.81 2 3/4 2 41/64
Dimensions, mm
3 -3M0-61 51.3 12.9 2.4 8.3
14 12.7
4 -4M0-61 53.6 13.7 2.4 9.9
6 -6M0-61 57.7 15.3 4.8 16 11.5 10.2
8 -8M0-61 61.0 16.2 6.4 18 13.1
11.2
10 -10M0-61 63.7 17.2 7.9 22 16.3
12 -12M0-61 71.0 22.8 9.5 24 19.5
14 -14M0-61 72.5 24.4 11.1 22.5
12.7
15 -15M0-61 72.5 24.4 11.9 27
22.8
16 -16M0-61 72.5 24.4 12.7
18 -18M0-61 78.9 24.4 15.1 30 26.0 16.8
20 -20M0-61 84.5 26.0 15.9 35 29.0
25 -25M0-61 96.0 31.3 21.8 41 34.0
30 -30M0-61 124 39.6 26.2 40.5 19.0
50
32 -32M0-61 128 42.0 28.6 42.5
38 -38M0-61 145 49.4 33.7 60 50.5
➀ Minimum panel thickness is 0.06 in.
Tube OD Dimensions
Basic Panel Max
Ordering Hole Panel
T Tx, in. Number A D Dx E F Size Thickness
Dimensions, mm
6 1/8 -6M0-61-2 55.1 15.3 12.7 2.4 16 11.5 10.2
Straight Fittings
FITTINGS
Male Connectors
TUBE
F flat
D
A
NPT
Basic NPT Basic
Dimensions Dimensions
Tube NPT Ordering Tube Size Ordering
OD Size Number A D E➀ F OD in. Number A D E➀ F
Dimensions, in. Dimensions, mm
1/16 -100-1-1 0.94 5/16 2 1/8 -2M0-1-2 30.5 12.9 1.7 12
1/16 1/8 -100-1-2 1.03 0.34 0.05 7/16 1/8 -3M0-1-2 30.5 12
1/4 -100-1-4 1.22 9/16 3 12.9 2.4
1/4 -3M0-1-4 35.6 14
1/16 -200-1-1 1.17 7/16 1/8 -4M0-1-2 31.2 12
1/8 -200-1-2 1.20 7/16 4 13.7 2.4
1/4 -4M0-1-4 36.3 14
1/8 1/4 -200-1-4 1.40 0.50 0.09 9/16
3/8 -200-1-6 1.41 11/16 1/8 -6M0-1-2 32.8 14
1/2 -200-1-8 1.66 7/8 1/4 -6M0-1-4 37.9 14
6 15.3 4.8
3/8 -6M0-1-6 38.4 18
1/8 -300-1-2 1.23 7/16 1/2 -6M0-1-8 44.7 22
3/16 0.54 0.12
1/4 -300-1-4 1.43 9/16
1/8 -8M0-1-2 34.2 4.8 15
1/16 -400-1-1 1.29 0.12 1/2 1/4 -8M0-1-4 38.7 6.4 15
1/8 -400-1-2 1.29 0.19 1/2 8 16.2
3/8 -8M0-1-6 39.3 6.4 18
1/4 -400-1-4 1.49 0.19 9/16
1/4 0.60 1/2 -8M0-1-8 45.6 6.4 22
3/8 -400-1-6 1.51 0.19 11/16
1/2 -400-1-8 1.76 0.19 7/8 1/8 -10M0-1-2 36.3 4.8 18
3/4 -400-1-12 1.82 0.19 1 1/16 1/4 -10M0-1-4 40.9 7.1 18
10 3/8 -10M0-1-6 40.9 17.2 7.9 18
1/8 -500-1-2 1.34 0.19 9/16 1/2 -10M0-1-8 46.5 7.9 22
5/16 1/4 -500-1-4 1.52 0.64 0.25 9/16 3/4 -10M0-1-12 48.0 7.9 27
3/8 -500-1-6 1.54 0.25 11/16
1/8 -12M0-1-2 38.8 4.8 22
1/8 -600-1-2 1.39 0.19 5/8 1/4 -12M0-1-4 43.4 7.1 22
1/4 -600-1-4 1.57 0.28 5/8 12 3/8 -12M0-1-6 43.4 22.8 9.5 22
3/8 -600-1-6 1.57 0.28 11/16 1/2 -12M0-1-8 49.0 9.5 22
3/8 0.66
1/2 -600-1-8 1.82 0.28 7/8 3/4 -12M0-1-12 50.5 9.5 27
3/4 -600-1-12 1.88 0.28 1 1/16
1 -600-1-16 2.14 0.28 1 3/8 1/4 -14M0-1-4 44.1 7.1
14 3/8 -14M0-1-6 44.1 24.4 9.5 24
1/8 -810-1-2 1.53 0.19 13/16 1/2 -14M0-1-8 49.0 11.1
1/4 -810-1-4 1.71 0.28 13/16
3/8 -810-1-6 1.71 0.38 13/16 15 1/2 -15M0-1-8 49.0 24.4 11.9 24
1/2 0.90
1/2 -810-1-8 1.93 0.41 7/8 3/8 -16M0-1-6 44.1 9.5 24
3/4 -810-1-12 1.99 0.41 1 1/16 16 1/2 -16M0-1-8 49.0 24.4 11.9 24
1 -810-1-16 2.25 0.41 1 3/8 3/4 -16M0-1-12 50.5 12.7 27
1/4 -1010-1-4 1.74 0.28 15/16 1/2 -18M0-1-8 11.9
18 50.5 24.4 27
3/8 -1010-1-6 1.74 0.38 15/16 3/4 -18M0-1-12 15.1
5/8 0.96
1/2 -1010-1-8 1.93 0.47 15/16 1/2 -20M0-1-8 11.9
3/4 -1010-1-12 1.99 0.50 1 1/16 20 52.3 26.0 30
3/4 -20M0-1-12 15.9
3/8 -1210-1-6 1.80 0.41 1 1/16 3/4 -22M0-1-12 52.3 15.9 30
22 26.0
1/2 -1210-1-8 1.99 0.47 1 1/16 1 -22M0-1-16 57.1 18.3 35
3/4 0.96
3/4 -1210-1-12 1.99 0.62 1 1/16 1/2 -25M0-1-8 57.5 11.9
1 -1210-1-16 2.25 0.62 1 3/8 25 3/4 -25M0-1-12 57.5 31.3 15.9 35
1/2 -1410-1-8 1.99 0.47 1 3/16 1 -25M0-1-16 62.3 21.8
7/8 3/4 -1410-1-12 1.99 1.02 0.62 1 3/16 1 -28M0-1-16 72.4 41
1 -1410-1-16 2.25 0.72 1 3/8 36.6 21.8
1 1/4 -28M0-1-20 73.1 46
1/2 -1610-1-8 2.26 0.47 28
1 B-28M0-1-16 75.0 41
1 3/4 -1610-1-12 2.26 1.23 0.62 1 3/8 31.6 24.6
1 1/4 B-28M0-1-20 77.3 46
1 -1610-1-16 2.45 0.88
30 1 1/4 -30M0-1-20 77.2 39.6 26.2 46
1 1/8 1 B-1810-1-16 2.45 1.23 0.88 1 5/8
32 1 1/4 -32M0-1-20 79.6 42.0 28.6 46
1 -2000-1-16 0.88
1 1/4 3.04 1.62 1 3/4 38 1 1/2 -38M0-1-24 91.6 49.4 33.7 55
1 1/4 -2000-1-20 1.09
1 1/2 1 1/2 -2400-1-24 3.50 1.97 1.34 2 1/8 ➀ The E dimension is the minimum nominal opening. These fittings may have
a larger opening at the pipe/straight thread end.
2 2 -3200-1-32 4.47 2.66 1.81 2 3/4
➀ The E dimension is the minimum nominal opening. These fittings may have
a larger opening at the pipe/straight thread end.
Straight Fittings
FITTINGS
Male Connectors
TUBE
F flat
D
A
Straight Fittings
FITTINGS
Male Connectors
TUBE
F flat
E
D
A
Straight Fittings
FITTINGS
Male Connectors
TUBE
F flat
D
A
Straight Fittings
FITTINGS
Male Connectors Bulkhead NPT
TUBE
F flat
Dimensions
NPT Basic Panel Max
E Tube Size Ordering Hole Panel
OD in. Number A D E➀ F Size Thickness
Dimensions, in.
D
A 1/8 1/8 -200-11-2 1.83 0.50 0.09 1/2 21/64 0.50
1/8 -400-11-2 1.95
1/4 0.60 0.19 5/8 29/64 0.40
1/4 -400-11-4 2.13
1/4 -600-11-4 2.26 3/4
3/8 3/8 -600-11-6 2.26 0.66 0.28 3/4 37/64 0.44
1/2 -600-11-8 2.51 7/8
3/8 -810-11-6 2.49 0.38
1/2 0.90 15/16 49/64 0.50
1/2 -810-11-8 2.71 0.41
3/4 3/4 -1210-11-12 3.00 0.96 0.62 1 3/16 1 1/64 0.66
1 1 -1610-11-16 3.67 1.23 0.88 1 5/8 1 21/64 0.75
Dimensions, mm
1/8 -6M0-11-2 49.5
6 15.3 4.8 16 11.5 10.2
1/4 -6M0-11-4 53.6
12 1/2 -12M0-11-8 68.8 22.8 9.5 24 19.5 12.7
➀ The E dimension is the minimum nominal opening. These fittings may have a larger opening at the
pipe/straight thread end.
F flat
O-ring
D E
A
Straight Fittings
FITTINGS
Male Connectors
TUBE
F flat
F flat
O-ring O-ring
E E
D D
A A
Fig. 1 Fig. 2
SAE/MS A B C D E
Thread NPT Min Min Min Max Max
Size Size Dia Dia Dia Depth Depth
D Dimensions, in.
5/16-24 0.16
— 0.50 0.59 0.66 0.09
5/16-24 0.22
— 1/8 0.69 0.78 0.88 0.16 0.28
➀ ➀ 3/8-24 — 0.56 0.66 0.75 0.09 0.22
A B
7/16-20 —
0.69 0.78 0.88 0.28
— 1/8
Fig. 3 ➀ Allow clearance for full thread. — 1/4 0.87 0.97 1.09
1/2-20 — 0.75 0.91 1.03 0.16
1/8 in. 0.31
9/16-18 — 0.81
0.97 1.09
— 1/4 0.87
E — 3/8 1.00 1.16 1.31 0.34
— 1/2 1.22 1.34 1.53 0.22 0.44
3/4-16 — 1.00 1.16 1.31 0.16 0.34
➀ — 1/2 1.22 1.34 1.53 0.44
C
1 1/16-12 — 1.41 1.53 1.75 0.22 0.50
1 5/16-12 — 1.69 1.78 2.03 0.56
Straight Fittings
FITTINGS
Male Connectors AN Fitting
TUBE
F flat AN Tube Basic
37° Dimensions
Tube Flare Ordering
OD Size Number A D E➀ F S
E
Dimensions, in.
S 1/16 1/8 -100-6-2AN 1.07 0.34 0.05 7/16 5/16-24UNJF-3
D
A 1/8 -200-6-2AN 1.27 0.06 7/16 5/16-24UNJF-3
1/8 0.50
1/4 -200-6-4AN 1.38 0.09 1/2 7/16-20UNJF-3
1/4 1/4 -400-6-4AN 1.48 0.60 0.17 1/2 7/16-20UNJF-3
5/16 5/16 -500-6-5AN 1.51 0.64 0.23 9/16 1/2-20UNJF-3
1/4 -600-6-4AN 0.17 7/16-20UNJF-3
3/8 1.56 0.66 5/8
3/8 -600-6-6AN 0.28 9/16-18UNJF-3
1/2 1/2 -810-6-8AN 1.81 0.90 0.39 13/16 3/4-16UNJF-3
3/4 3/4 -1210-6-12AN 2.10 0.96 0.61 1 1/8 1 1/16-12UNJ-3
1 1 -1610-6-16AN 2.42 1.23 0.84 1 3/8 1 5/16-12UNJ-3
➀ The E dimension is the minimum nominal opening. These fittings may have a larger opening at the
pipe/straight thread end.
AN Bulkhead Fitting
F flat F flat
AN Dimensions
37°
Tube Basic Panel Max
Tube Flare Ordering Hole Panel
E
OD Size Number A D E F S Size Thickness
Dimensions, in.
S
D 1/4 1/4 -400-61-4AN 2.12 0.60 0.17 5/8 7/16-20UNJF-3 29/64 0.40
A
3/8 3/8 -600-61-6AN 2.25 0.66 0.28 3/4 9/16-18UNJF-3 37/64 0.44
1/2 1/2 -810-61-8AN 2.59 0.90 0.39 15/16 3/4-16UNJF-3 49/64 0.50
3/4 3/4 -1210-61-12AN 3.11 0.96 0.61 1 3/16 1 1/16-12UNJ-3 1 1/64 0.66
1 1 -1610-61-16AN 3.64 1.23 0.84 1 5/8 1 5/16-12UNJ-3 1 21/64 0.75
Straight Fittings
FITTINGS
F flat
Gasket Basic
Dimensions
E Tube Ordering
OD Number A D E➀ F
Dimensions, in.
1/8 -200-1-0157 0.95 0.50 7/16
D 0.09
A 1/4 -400-1-0256 1.08 0.60 9/16
➀ The E dimension is the minimum nominal opening. These fittings
may have a larger opening at the pipe/straight thread end.
M5 × 0.8 Thread
F flat
Basic
Dimensions
E Tube Ordering
OD Number A D E➀ F
Dimensions, mm
6 -6M0-1-0046 29.2 15.3 2.0 14
D
A ➀ The E dimension is the minimum nominal opening. These fittings
may have a larger opening at the pipe/straight thread end.
F flat Basic
Dimensions
E
Tube Ordering
OD Number A D E➀ F
E
Dimensions, mm
-6M0-1-M10X1.0RS 36.3 3.2
6 15.3 14
D -6M0-1-M12X1.0RS 40.4 4.8
A
12 -12M0-1-M16X1.5RS 45.5 22.8 9.5 22
➀ The E dimension is the minimum nominal opening. These fittings may
have a larger opening at the pipe/straight thread end.
Straight Fittings
SWAGELOK MALE PIPE WELD CONNECTOR CUTAWAY-MS-01-140 C-PH-0364-DIM
FITTINGS
Weld Connectors Male Pipe Weld (Fractional)
TUBE
F flat
37.5°
Pipe Basic
Dimensions
Tube Weld Ordering
OD Size Number A D E➀ F J
E J
Dimensions, in.
1/8 1/8 -200-1-2W 1.20 0.50 0.09 7/16 0.405
D
A 3/16 1/8 -300-1-2W 1.23 0.54 0.12 7/16 0.405
1/8 -400-1-2W 1.29 1/2 0.405
1/4 0.60 0.19
1/4 -400-1-4W 1.49 9/16 0.540
1/8 -500-1-2W 1.34 0.21 0.405
5/16 0.64 9/16
1/4 -500-1-4W 1.52 0.25 0.540
1/4 -600-1-4W 1.57 5/8 0.540
3/8 -600-1-6W 1.57 11/16 0.675
3/8 0.66 0.28
1/2 -600-1-8W 1.82 7/8 0.840
3/4 -600-1-12W 1.88 1 1/6 1.050
3/8 -810-1-6W 1.71 13/16 0.675
1/2 -810-1-8W 1.93 7/8 0.840
1/2 0.90 0.41
3/4 -810-1-12W 1.99 1 1/16 1.050
1 -810-1-16W 2.25 1 3/8 1.315
5/8 1/2 -1010-1-8W 1.93 0.96 0.50 15/16 0.840
1/2 -1210-1-8W 0.55 0.840
3/4 1.99 0.96 1 1/16
3/4 -1210-1-12W 0.62 1.050
1 1 -1610-1-16W 2.45 1.23 0.88 1 3/8 1.315
1 1/4 1 1/4 -2000-1-20W 3.04 1.62 1.09 1 3/4 1.660
1 1/2 1 1/2 -2400-1-24W 3.50 1.97 1.34 2 1/8 1.900
2 2 -3200-1-32W 4.47 2.66 1.81 2 3/4 2.375
➀ The E dimension is the minimum nominal opening. These fittings may have a larger
opening at the weld end. Wall thickness at the weld end is based on schedule 80 pipe.
Pipe
Weld Basic
Dimensions
Tube Size Ordering
OD in. Number A D E➀ F F, in.➁ J
Dimensions, mm
3 1/8 -3M0-1-2W 30.5 12.9 2.4 12 1/2 10.3
4 1/8 -4M0-1-2W 31.2 13.7 2.4 12 1/2 10.3
1/8 -6M0-1-2W 32.8 1/2 10.3
6 15.3 4.8 14
1/4 -6M0-1-4W 37.9 9/16 13.7
1/8 -8M0-1-2W 34.2 5.4 15 9/16 10.3
8 1/4 -8M0-1-4W 38.7 16.2 6.4 15 9/16 13.7
1/2 -8M0-1-8W 45.6 6.4 22 7/8 21.3
1/4 -10M0-1-4W 40.9 7.5 18 11/16 13.7
10 3/8 -10M0-1-6W 40.9 17.2 7.9 18 11/16 17.1
1/2 -10M0-1-8W 46.5 7.9 22 7/8 21.3
1/4 -12M0-1-4W 43.4 7.5 22 13/16 13.7
3/8 -12M0-1-6W 43.4 9.5 22 13/16 17.1
12 22.8
1/2 -12M0-1-8W 49.0 9.5 22 7/8 21.3
3/4 -12M0-1-12W 50.5 9.5 27 1 1/16 26.7
14 3/8 -14M0-1-6W 44.1 24.4 10.7 24 15/16 17.1
15 1/2 -15M0-1-8W 49.0 24.4 11.9 24 15/16 21.3
16 1/2 -16M0-1-8W 49.0 24.4 12.7 24 15/16 21.3
18 1/2 -18M0-1-8W 50.5 24.4 13.9 27 1 1/16 21.3
30 1 1/4 -30M0-1-20W 77.2 39.6 26.2 46 46 mm 42.2
32 1 1/4 -32M0-1-20W 79.6 42.0 28.6 46 46 mm 42.2
38 1 1/2 -38M0-1-24W 91.6 49.4 33.7 55 55 mm 48.3
➀ The E dimension is the minimum nominal opening. These fittings may have a larger opening at the
weld end. Wall thickness at the weld end is based on schedule 80 pipe.
➁ This dimension is for steel and aluminum fittings.
Straight Fittings
FITTINGS
Female Connectors
TUBE
F flat
E
D
A
NPT
Basic NPT Basic
Dimensions Dimensions
Tube NPT Ordering Tube Size Ordering
OD Size Number A D E F OD in. Number A D E F
Dimensions, in. Dimensions, mm
1/16 -100-7-1 0.93 7/16 1/8 -3M0-7-2 28.7 14
1/16 0.34 0.05 3 12.9 2.4
1/8 -100-7-2 0.96 9/16 1/4 -3M0-7-4 33.5 19
1/8 -200-7-2 1.13 9/16 4 1/8 -4M0-7-2 29.7 13.7 2.4 14
1/8 0.50 0.09
1/4 -200-7-4 1.32 3/4 1/8 -6M0-7-2 31.3 14
3/16 1/8 -300-7-2 1.17 0.54 0.12 9/16 1/4 -6M0-7-4 35.8 19
6 15.3 4.8
1/8 -400-7-2 1.23 9/16 3/8 -6M0-7-6 37.6 22
1/4 -400-7-4 1.41 3/4 1/2 -6M0-7-8 42.5 27
1/4 0.60 0.19
3/8 -400-7-6 1.48 7/8 1/8 -8M0-7-2 32.1 15
1/2 -400-7-8 1.67 1 1/16 1/4 -8M0-7-4 37.0 19
8 16.2 6.4
1/8 -500-7-2 1.26 9/16 3/8 -8M0-7-6 38.5 22
5/16 0.64 0.25 1/2 -8M0-7-8 43.3 27
1/4 -500-7-4 1.45 3/4
1/8 -600-7-2 1.29 5/8 1/4 -10M0-7-4 37.8 19
1/4 -600-7-4 1.48 3/4 10 3/8 -10M0-7-6 39.4 17.2 7.9 22
3/8 3/8 -600-7-6 1.54 0.66 0.28 7/8 1/2 -10M0-7-8 44.2 27
1/2 -600-7-8 1.73 1 1/16 1/4 -12M0-7-4 40.3 22
3/4 -600-7-12 1.88 1 5/16 12 3/8 -12M0-7-6 41.9 22.8 9.5 22
1/4 -810-7-4 1.59 13/16 1/2 -12M0-7-8 46.7 27
3/8 -810-7-6 1.65 7/8 15 1/2 -15M0-7-8 46.7 24.4 11.9 27
1/2 0.90 0.41
1/2 -810-7-8 1.84 1 1/16 16 1/2 -16M0-7-8 46.9 24.4 12.7 27
3/4 -810-7-12 1.90 1 5/16
1/2 -20M0-7-8 47.9 30
3/8 -1010-7-6 1.65 15/16 20 26.0 15.9
3/4 -20M0-7-12 49.7 35
5/8 1/2 -1010-7-8 1.84 0.96 0.50 1 1/16
3/4 -1010-7-12 1.90 1 5/16 3/4 -22M0-7-12 49.7 35
22 26.0 18.3
1 -22M0-7-16 57.9 41
1/2 -1210-7-8 1.84 1 1/16
3/4 0.96 0.62 3/4 -25M0-7-12 53.4 35
3/4 -1210-7-12 1.90 1 5/16 25 31.3 21.8
1 -25M0-7-16 62.3 41
7/8 3/4 -1410-7-12 1.96 1.02 0.72 1 5/16
3/4 -1610-7-12 2.10 1 3/8
1 1.23 0.88
1 -1610-7-16 2.45 1 5/8
1 1/4 1 1/4 -2000-7-20 2.94 1.62 1.09 2 1/8
1 1/2 1 1/2 -2400-7-24 3.28 1.97 1.34 2 3/8
2 2 -3200-7-32 4.00 2.66 1.81 2 7/8
Straight Fittings
FITTINGS
Female Connectors
TUBE
F flat
F flat E
E
ISO/BSP parallel thread
(RJ) fittings are available in
See page 9 for thread
stainless steel only.
specifications.
See page 9 for thread
specifications.
D D
A A
ISO ISO
Thread Basic Thread
Dimensions Dimensions
Tube Size Ordering Tube Size Ordering
OD in. Number A D E F OD in. Number A D E F
Dimensions, in. Dimensions, in.
1/8 1/8 -200-7-2RT 1.13 0.50 0.09 9/16 1/4 SS-400-7-4RJ 1.48 0.18 3/4
1/8 -400-7-2RT 1.23 9/16 1/4 3/8 SS-400-7-6RJ 1.48 0.60 0.19 15/16
1/4 -400-7-4RT 1.41 3/4 1/2 SS-400-7-8RJ 1.71 0.19 1 1/16
1/4 0.60 0.19 1/4 SS-500-7-4RJ 1.51 0.22 3/4
3/8 -400-7-6RT 1.48 7/8 5/16 0.64
1/2 -400-7-8RT 1.67 1 1/16 1/2 SS-500-7-8RJ 1.61 0.28 1 1/16
1/4 -600-7-4RT 1.48 3/4 1/4 SS-600-7-4RJ 1.54 0.22 3/4
3/8 3/8 -600-7-6RT 1.54 0.66 0.28 7/8 3/8 3/8 SS-600-7-6RJ 1.52 0.66 0.26 15/16
1/2 -600-7-8RT 1.73 1 1/16 1/2 SS-600-7-8RJ 1.65 0.28 1 1/16
1/4 -810-7-4RT 1.59 13/16 1/4 SS-810-7-4RJ 1.65 0.22 13/16
1/2 3/8 -810-7-6RT 1.65 0.90 0.41 7/8 1/2 3/8 SS-810-7-6RJ 1.75 0.90 0.26 15/16
1/2 -810-7-8RT 1.84 1 1/16 1/2 SS-810-7-8RJ 1.90 0.28 1 1/16
Dimensions, mm Dimensions, mm
3 1/8 -3M0-7-2RT 28.7 12.9 2.4 14 1/4 SS-6M0-7-4RJ 37.6 19
6 3/8 SS-6M0-7-6RJ 37.6 15.3 4.8 24
1/8 -6M0-7-2RT 31.3 14
1/2 SS-6M0-7-8RJ 43.5 27
1/4 -6M0-7-4RT 35.8 19
6 15.3 4.8 1/4 SS-8M0-7-4RJ 38.5 5.5 19
3/8 -6M0-7-6RT 37.6 22
1/2 -6M0-7-8RT 42.5 27 8 3/8 SS-8M0-7-6RJ 36.2 16.2 6.5 24
1/2 SS-8M0-7-8RJ 41.0 7.0 27
1/8 -8M0-7-2RT 32.1 15
1/4 -8M0-7-4RT 37.0 19 1/4 SS-10M0-7-4RJ 39.4 5.5 19
8 16.2 6.4 10 3/8 SS-10M0-7-6RJ 38.8 17.2 6.5 24
3/8 -8M0-7-6RT 38.5 22
1/2 -8M0-7-8RT 43.3 27 1/2 SS-10M0-7-8RJ 42.1 7.0 27
1/8 -10M0-7-2RT 33.0 18 1/4 SS-12M0-7-4RJ 41.9 5.5 22
1/4 -10M0-7-4RT 37.8 19 12 3/8 SS-12M0-7-6RJ 44.4 22.8 6.5 24
10 17.2 7.9 1/2 SS-12M0-7-8RJ 48.2 7.0 27
3/8 -10M0-7-6RT 39.4 22
1/2 -10M0-7-8RT 44.2 27
1/8 -12M0-7-2RT 35.5 8.3 22
1/4 -12M0-7-4RT 40.3 9.5 22
12 3/8 -12M0-7-6RT 41.9 22.8 9.5 22 F flat
1/2 -12M0-7-8RT 46.7 9.5 27 E
3/4 -12M0-7-12RT 49.0 9.5 35
3/8 -15M0-7-6RT 41.9 24 See page 9 for thread
15 24.4 11.9
1/2 -15M0-7-8RT 46.7 27 specifications.
1/2 -20M0-7-8RT 47.9 30
20 26.0 15.9 D
3/4 -20M0-7-12RT 49.7 35
A
3/4 -22M0-7-12RT 49.7 35
22 26.0 18.3
1 -22M0-7-16RT 57.9 41 ISO/BSP Parallel Thread (RP)
3/4 -25M0-7-12RT 53.4 35
25 31.3 21.8
1 -25M0-7-16RT 62.3 41 ISO
Thread Basic
Dimensions
Tube Size Ordering
OD in. Number A D E F
Dimensions, mm
1/8 -6M0-7-2RP 33.5 14
6 15.3 4.8
1/4 -6M0-7-4RP 39.4 19
22 3/4 -22M0-7-12RP 53.3 26.0 18.3 35
25 1 -25M0-7-16RP 63.9 26.5 21.8 40
Straight Fittings
FITTINGS
F flat ISO
E Thread Basic
Dimensions
Tube Size Ordering
OD in. Number A D E F
Dimensions, in.
D 1/8 1/4 -200-7-4RG 1.39 0.59 0.09 3/4
A 1/8 -400-7-2RG 1.26 0.18 9/16
1/4 -400-7-4RG 1.48 0.19 3/4
1/4 0.60
See page 9 for thread specifications. 3/8 -400-7-6RG 1.48 0.19 15/16
ISO/BSP parallel gaskets are available. 1/2 -400-7-8RG 1.71 0.19 1 1/16
See page 60. 1/4 -500-7-4RG 1.51 0.22 3/4
5/16 0.64
1/2 -500-7-8RG 1.61 0.28 1 1/16
1/4 -600-7-4RG 1.54 0.22 3/4
3/8 3/8 -600-7-6RG 1.52 0.66 0.26 15/16
1/2 -600-7-8RG 1.65 0.28 1 1/16
3/8 -810-7-6RG 1.75 0.26 15/16
1/2 0.90
1/2 -810-7-8RG 1.90 0.28 1 1/16
Dimensions, mm
3 1/4 -3M0-7-4RG 35.3 12.9 2.4 19
1/8 -6M0-7-2RG 32.0 4.5 14
1/4 -6M0-7-4RG 37.6 4.8 19
6 15.3
3/8 -6M0-7-6RG 37.6 4.8 24
1/2 -6M0-7-8RG 43.5 4.8 27
1/4 -8M0-7-4RG 38.5 5.5 19
8 3/8 -8M0-7-6RG 36.2 16.2 6.5 24
1/2 -8M0-7-8RG 41.0 7.0 27
1/4 -10M0-7-4RG 39.4 5.5 19
10 3/8 -10M0-7-6RG 38.8 17.2 6.5 24
1/2 -10M0-7-8RG 42.1 7.0 27
1/4 -12M0-7-4RG 41.9 5.5 22
12 3/8 -12M0-7-6RG 44.4 22.8 6.5 24
1/2 -12M0-7-8RG 48.2 7.0 27
20 1/2 -20M0-7-8RG 54.3 26.0 7.0 30
22 1/2 -22M0-7-8RG 54.3 26.0 7.0 30
Bulkhead NPT
F flat
Dimensions
E
NPT Basic Panel Max
Tube Size Ordering Hole Panel
OD in. Number A D E F Size Thickness
Dimensions, in.
D 1/8 1/8 -200-71-2 1.76 0.50 0.09 9/16 21/64 0.50
A
1/8 -400-71-2 1.85 5/8
1/4 0.60 0.19 29/64 0.40
1/4 -400-71-4 2.04 3/4
3/8 1/4 -600-71-4 2.17 0.66 0.28 3/4 37/64 0.44
3/8 -810-71-6 2.43 15/16
1/2 0.90 0.41 49/64 0.50
1/2 -810-71-8 2.62 1 1/16
Dimensions, mm
6 1/4 -6M0-71-4 51.8 15.3 4.8 19 11.5 10.2
12 1/2 -12M0-71-8 66.5 22.8 9.5 27 19.5 12.7
FITTINGS
Reducers
TUBE
G flat
F flat
F flat F flat
T Tx T Tx T Tx
D E D D E
A E A
A
1 in. and Under Over 1 in. 25 mm and Under
Straight Fittings
FITTINGS
Reducers
TUBE
F flat F flat
T Tx T Tx
D E D E
A A
Long Reducer
F flat
Basic
Tube OD Dimensions
Ordering
T E Tx T Tx Number A D E F
Dimensions, in.
D
3/8 1/2 -600-RF-8 2.57 0.66 0.25 5/8
A Use only long reducers in female Swagelok end connections.
Bulkhead Reducer
F flat F flat
Dimensions
Basic Panel Max
E Tube Ordering Hole Panel
OD Number A D E F Size Thickness
Dimensions, in.
D
A 1/8 -200-R1-2 1.95 0.50 0.08 1/2 21/64 0.50
1/4 -400-R1-4 2.20 0.60 0.17 5/8 29/64 0.40
3/8 -600-R1-6 2.41 0.66 0.27 3/4 37/64 0.44
1/2 -810-R1-8 2.87 0.90 0.37 15/16 49/64 0.50
5/8 -1010-R1-10 2.96 0.96 0.47 1 1/16 57/64 0.50
3/4 -1210-R1-12 3.21 0.96 0.58 1 3/16 1 1/64 0.66
1 -1610-R1-16 3.95 1.23 0.80 1 5/8 1 21/64 0.75
Straight Fittings
FITTINGS
Port Connectors Port Connector
TUBE
Basic Basic
Dimensions Dimensions
Tube Ordering Tube Ordering
E OD Number E H OD Number E H
Dimensions, in. Dimensions, mm
H
1/16 -101-PC 0.03 0.54 3 -3M1-PC 1.9 22.2
1 in./25 mm 1/8 -201-PC 0.08 0.88 6 -6M1-PC 4.1 25.0
and under
1/4 -401-PC 0.17 0.98 8 -8M1-PC 5.6 26.0
5/16 -501-PC 0.22 1.02 10 -10M1-PC 7.1 27.1
3/8 -601-PC 0.27 1.05 12 -12M1-PC 8.8 36.2
1/2 -811-PC 0.37 1.43 15 -15M1-PC 11.2 37.8
E
5/8 -1011-PC 0.47 1.49 16 -16M1-PC 12.0 37.8
3/4 -1211-PC 0.58 1.49 18 -18M1-PC 13.9 37.8
1 -1611-PC 0.80 1.94 20 -20M1-PC 15.5 39.4
H 1 1/4 -2000-PC➀ 1.02 2.72 25 -25M1-PC 19.9 49.3
Over 1 in./25mm 1 1/2 -2400-PC➀ 1.25 3.31 28 B-28M1-PC 22.6 49.0
2 -3200-PC➀ 1.72 4.56 28 -28M0-PC➀ 22.5 63.5
➀ Furnished with nuts and preswaged ferrules. 30 -30M0-PC➀ 24.3 67.6
32 -32M0-PC➀ 26.5 69.7
38 -38M0-PC➀ 31.6 81.9
➀ Furnished with nuts and preswaged ferrules.
Straight Fittings
FITTINGS
D
A
Cap Plug
Basic Basic Basic Basic
Tube Ordering Tube Ordering Tube Ordering Tube Ordering
OD Number A D OD Number A D OD Number OD Number
Dimensions, in. Dimensions, mm Dimensions, in. Dimensions, mm
1/16 -100-C 0.59 0.34 2 -2M0-C 20.1 12.9 1/16 -100-P 2 -2M0-P
1/8 -200-C 0.79 0.50 3 -3M0-C 20.1 12.9 1/8 -200-P 3 -3M0-P
3/16 -300-C 0.84 0.54 4 -4M0-C 21.3 13.7 3/16 -300-P 4 -4M0-P
1/4 -400-C 0.92 0.60 6 -6M0-C 23.1 15.3 1/4 -400-P 6 -6M0-P
5/16 -500-C 0.96 0.64 8 -8M0-C 24.5 16.2 5/16 -500-P 8 -8M0-P
3/8 -600-C 1.01 0.66 10 -10M0-C 26.6 17.2 3/8 -600-P 10 -10M0-P
1/2 -810-C 1.21 0.90 12 -12M0-C 30.6 22.8 1/2 -810-P 12 -12M0-P
5/8 -1010-C 1.24 0.96 14 -14M0-C 31.4 24.4 5/8 -1010-P 14 -14M0-P
3/4 -1210-C 1.27 0.96 15 -15M0-C 31.4 24.4 3/4 -1210-P 15 -15M0-P
7/8 -1410-C 1.37 1.02 16 -16M0-C 31.4 24.4 7/8 -1410-P 16 -16M0-P
1 -1610-C 1.61 1.23 18 -18M0-C 32.2 24.4 1 -1610-P 18 -18M0-P
1 1/8 B-1810-C 1.61 1.23 20 -20M0-C 34.8 26.0 1 1/4 -2000-P 20 -20M0-P
1 1/4 -2000-C 2.10 1.62 22 -22M0-C 34.8 26.0 1 1/2 -2400-P 22 -22M0-P
1 1/2 -2400-C 2.54 1.97 25 -25M0-C 41.0 31.3 2 -3200-P 25 -25M0-P
2 -3200-C 3.41 2.66 -28M0-C 48.5 36.6 28 -28M0-P
28
B-28M0-C 41.2 31.6 30 -30M0-P
30 -30M0-C 53.4 39.6 32 -32M0-P
32 -32M0-C 55.8 42.0 38 -38M0-P
38 -38M0-C 65.4 49.4
NPT Ordering
Size Number A E F
Dimensions, in.
1/8 SS-MD-2 0.56 0.19 1/2
1/4 SS-MD-4 0.78 0.28 9/16
3/8 SS-MD-6 0.81 0.41 11/16
1/2 SS-MD-8 1.03 0.50 7/8
3/4 SS-MD-12 1.06 0.72 1 1/16
90° Elbows
FITTINGS
Unions
TUBE
E
F flat
Basic Basic
Dimensions Dimensions
Tube Ordering Tube Ordering
OD Number A D E F OD Number A D E F, in.
Dimensions, in. Dimensions, mm
1/16 -100-9 0.70 0.34 0.05 3/8 3 -3M0-9 22.3 12.9 2.4 3/8
1/8 -200-9 0.88 0.50 0.09 3/8 4 -4M0-9 25.4 13.7 2.4 1/2
3/16 -300-9 1.00 0.54 0.12 1/2 6 -6M0-9 27.0 15.3 4.8 1/2
1/4 -400-9 1.06 0.60 0.19 1/2 8 -8M0-9 28.8 16.2 6.4 9/16
5/16 -500-9 1.13 0.64 0.25 9/16 10 -10M0-9 31.5 17.2 7.9 11/16
3/8 -600-9 1.20 0.66 0.28 5/8 12 -12M0-9 36.0 22.8 9.5 13/16
1/2 -810-9 1.42 0.90 0.41 13/16 14 -14M0-9 38.0 24.4 11.1 15/16
5/8 -1010-9 1.50 0.96 0.50 15/16 15 -15M0-9 38.0 24.4 11.9 15/16
3/4 -1210-9 1.57 0.96 0.62 1 1/16 16 -16M0-9 38.0 24.4 12.7 15/16
7/8 -1410-9 1.76 1.02 0.72 1 3/8 18 -18M0-9 39.8 24.4 15.1 1 1/16
1 -1610-9 1.93 1.23 0.88 1 3/8 20 -20M0-9 44.6 26.0 15.9 1 3/8
1 1/8 B-1810-9 2.17 1.23 0.97 1 11/16 22 -22M0-9 44.6 26.0 18.3 1 3/8
1 1/4 -2000-9 2.67 1.62 1.09 1 11/16 25 -25M0-9 49.1 31.3 21.8 1 3/8
1 1/2 -2400-9 3.10 1.97 1.34 2 -28M0-9 64.0 36.6 21.8 41 mm
28
2 -3200-9 4.22 2.66 1.81 2 3/4 B-28M0-9 55.4 31.6 24.6 1 11/16
30 -30M0-9 69.9 39.6 26.2 46 mm
32 -32M0-9 72.3 42.0 28.6 46 mm
38 -38M0-9 84.0 49.4 33.7 55 mm
50 -50M0-9 106 65.0 45.2 2 3/4
90° Elbows
FITTINGS
Male
TUBE
E
F flat
NPT
Basic NPT Basic
Dimensions Dimensions
Tube NPT Ordering Tube Size Ordering
OD Size Number A D E➀ F OD in. Number A D E➀ F, in.
Dimensions, in. Dimensions, mm
1/16 -100-2-1 1/8 -3M0-2-2 23.6 7/16
1/16 0.75 0.34 0.05 7/16 3 12.9 2.4
1/8 -100-2-2 1/4 -3M0-2-4 24.6 1/2
1/16 -200-2-1 0.93 7/16 1/8 -4M0-2-2
4 25.4 13.7 2.4 1/2
1/8 1/8 -200-2-2 0.93 0.50 0.09 7/16 1/4 -4M0-2-4
1/4 -200-2-4 0.97 1/2 1/8 -6M0-2-2 27.0 1/2
1/8 -300-2-2 1/4 -6M0-2-4 27.0 1/2
3/16 1.00 0.54 0.12 1/2 6 15.3 4.8
1/4 -300-2-4 3/8 -6M0-2-6 29.8 11/16
1/16 -400-2-1 1.06 0.12 1/2 1/2 -6M0-2-8 31.8 13/16
1/8 -400-2-2 1.06 0.19 1/2 1/8 -8M0-2-2 28.8 4.8 9/16
1/4 1/4 -400-2-4 1.06 0.60 0.19 1/2 1/4 -8M0-2-4 28.8 6.4 9/16
3/8 -400-2-6 1.17 0.19 11/16 8 16.2
3/8 -8M0-2-6 30.6 6.4 11/16
1/2 -400-2-8 1.25 0.19 13/16 1/2 -8M0-2-8 32.6 6.4 13/16
1/8 -500-2-2 1.13 0.19 9/16 1/8 -10M0-2-2 31.5 4.8 11/16
5/16 1/4 -500-2-4 1.13 0.64 0.25 9/16 1/4 -10M0-2-4 31.5 7.1 11/16
3/8 -500-2-6 1.20 0.25 11/16 10 17.2
3/8 -10M0-2-6 31.5 7.9 11/16
1/8 -600-2-2 1.20 0.19 5/8 1/2 -10M0-2-8 33.5 7.9 13/16
1/4 -600-2-4 1.20 0.28 5/8 1/4 -12M0-2-4 36.0 7.1 13/16
3/8 3/8 -600-2-6 1.23 0.66 0.28 11/16 3/8 -12M0-2-6 36.0 9.5 13/16
1/2 -600-2-8 1.31 0.28 13/16 12 22.8
1/2 -12M0-2-8 36.0 9.5 13/16
3/4 -600-2-12 1.46 0.28 1 1/16 3/4 -12M0-2-12 39.8 9.5 1 1/16
1/4 -810-2-4 1.42 0.28 13/16 14 1/2 -14M0-2-8 38.0 24.4 11.1 15/16
3/8 -810-2-6 1.42 0.38 13/16
1/2 0.90 15 1/2 -15M0-2-8 38.0 24.4 11.9 15/16
1/2 -810-2-8 1.42 0.41 13/16
3/4 -810-2-12 1.57 0.41 1 1/16 3/8 -16M0-2-6 38.0 9.5 15/16
16 1/2 -16M0-2-8 38.0 24.4 11.9 15/16
3/8 -1010-2-6 1.50 0.38 15/16 3/4 -16M0-2-12 39.8 12.7 1 1/16
5/8 1/2 -1010-2-8 1.50 0.96 0.47 15/16
3/4 -1010-2-12 1.57 0.50 1 1/16 1/2 -18M0-2-8 11.9
18 39.8 24.4 1 1/16
3/4 -18M0-2-12 15.1
1/2 -1210-2-8 0.47
3/4 1.57 0.96 1 1/16 1/2 -20M0-2-8 11.9
3/4 -1210-2-12 0.62 20 44.6 26.0 1 3/8
3/4 -20M0-2-12 15.9
7/8 3/4 -1410-2-12 1.76 1.02 0.62 1 3/8
3/4 -22M0-2-12 15.9
3/4 -1610-2-12 0.62 22 44.6 26.0 1 3/8
1 1.93 1.23 1 3/8 1 -22M0-2-16 18.3
1 -1610-2-16 0.88
3/4 -25M0-2-12 15.9
1 1/4 1 1/4 -2000-2-20 2.67 1.62 1.09 1 11/16 25 49.1 31.3 1 3/8
1 -25M0-2-16 21.8
1 1/2 1 1/2 -2400-2-24 3.10 1.97 1.34 2 30 1 1/4 -30M0-2-20 69.9 39.6 26.2 46 mm
2 2 -3200-2-32 4.22 2.66 1.81 2 3/4 32 1 1/4 -32M0-2-20 72.3 42.0 27.8 46 mm
➀ The E dimension is the minimum nominal opening. These fittings may have 38 1 1/2 -38M0-2-24 84.0 49.4 33.7 55 mm
a larger opening at the pipe/straight thread end.
➀ The E dimension is the minimum nominal opening. These fittings may have
a larger opening at the pipe/straight thread end.
90° Elbows
FITTINGS
Male
TUBE
E
F flat
90° Elbows
FITTINGS
TUBE
Reducing Elbows
E
F flat
Basic
Tube OD Dimensions
Ordering
T
T Tx Number A D E F, in.
Dimensions, in.
D 1/4 -400-2R-4 1.06 0.60 0.17 1/2
1/4
3/8 -600-2R-4 1.20 0.66 0.17 5/8
3/8 -600-2R-6 1.20 0.66 0.27 5/8
3/8
1/2 -810-2R-6 1.42 0.90 0.27 13/16
A
Tx 1/2 1/2 -810-2R-8 1.42 0.90 0.37 13/16
Dimensions, mm
6 6 -6M0-2R-6M 27.0 15.3 4.6 1/2
12 12 -12M0-2R-12M 38.1 22.8 8.8 15/16
Gaugeable Tube Fittings and Adapter Fittings 37
90° Elbows
FITTINGS
Male Positionable, ISO/BSP Parallel Thread (PR)
TUBE
A ISO
F flat Thread Basic
Dimensions
Tube Size Ordering
OD in. Number A D E➀ F, in. Fx, in. U
Dimensions, in.
D E 1/8 -400-2-2PR 1.06 0.16 1/2 9/16 0.60
1/4 0.60
1/4 -400-2-4PR 1.14 0.19 5/8 3/4 0.80
Fx flat
1/4 -600-2-4PR 1.20 0.23 5/8 3/4 0.80
3/8 0.66
O-ring 3/8 -600-2-6PR 1.31 0.28 13/16 7/8 0.96
1/4 -810-2-4PR 1.42 0.23 13/16 3/4 0.80
U 1/2 3/8 -810-2-6PR 1.42 0.90 0.31 13/16 7/8 0.96
retainer OD
1/2 -810-2-8PR 1.50 0.41 15/16 1 1/16 1.16
5/8 1/2 -1010-2-8PR 1.50 0.96 0.47 15/16 1 1/16 1.16
1/2 -1210-2-8PR 0.47 1 1/16 1.16
3/4 1.57 0.96 1 1/16
3/4 -1210-2-12PR 0.62 1 3/8 1.43
3/4 -1610-2-12PR 0.62 1 3/8 1.43
1 1.93 1.23 1 3/8
1 -1610-2-16PR 0.78 1 5/8 1.82
Dimensions, mm
1/8 -6M0-2-2PR 27.0 4.0 1/2 9/16 15.2
6 15.3
1/4 -6M0-2-4PR 29.0 4.8 5/8 3/4 20.3
1/8 -8M0-2-2PR 28.8 4.0 9/16 9/16 15.2
8 16.2
1/4 -8M0-2-4PR 29.9 5.9 5/8 3/4 20.3
1/4 -10M0-2-4PR 5.9 3/4 20.3
10 33.5 17.2 13/16
3/8 -10M0-2-6PR 7.9 7/8 24.4
1/4 -12M0-2-4PR 36.0 5.9 13/16 3/4 20.3
3/8 -12M0-2-6PR 36.0 7.9 13/16 7/8 24.4
12 22.8
1/2 -12M0-2-8PR 38.0 9.5 15/16 1 1/16 29.5
3/4 -12M0-2-12PR 39.8 9.5 1 1/16 1 3/8 36.3
➀ The E dimension is the minimum nominal opening. These fittings may have a larger opening at the
pipe/straight thread end.
90° Elbows
FITTINGS
A Socket Basic
E Dimensions
F flat Tube Weld Ordering
OD Size Number A B D E F K
Dimensions, in.
1/4 1/4 -400-9-4W 1.06 0.28 0.60 0.19 1/2 0.50
D 3/8 3/8 -600-9-6W 1.20 0.31 0.66 0.28 5/8 0.63
B
1/2 1/2 -810-9-8W 1.42 0.38 0.90 0.41 13/16 0.81
K 3/4 3/4 -1210-9-12W 1.57 0.44 0.96 0.62 1 1/16 1.06
1 1 -1610-9-16W 1.93 0.62 1.23 0.88 1 3/8 1.38
A Pipe Basic
E Dimensions
F flat Tube Weld Ordering
OD Size Number A D E➀ F J
Dimensions, in.
1/8 -400-2-2W 0.405
1/4 1.06 0.60 0.19 1/2
D 1/4 -400-2-4W 0.540
3/8 1/4 -600-2-4W 1.20 0.66 0.28 5/8 0.540
37.5°
1/2 1/2 -810-2-8W 1.42 0.90 0.41 13/16 0.840
J 3/4 3/4 -1210-2-12W 1.57 0.96 0.62 1 1/16 1.050
➀ The E dimension is the minimum nominal opening. These fittings may have a larger
opening at the weld end. Wall thickness at the weld end is based on schedule 80 pipe.
Female
E
F flat
A
NPT
Basic NPT Basic
Dimensions Dimensions
Tube NPT Ordering Tube Size Ordering
OD Size Number A D E F OD in. Number A D E F, in.
Dimensions, in. Dimensions, mm
1/8 -200-8-2 0.97 1/2 1/8 -6M0-8-2 27.0 1/2
1/8 0.50 0.09
1/4 -200-8-4 1.08 11/16 6 1/4 -6M0-8-4 29.8 15.3 4.8 11/16
3/16 1/8 -300-8-2 1.00 0.54 0.12 1/2 1/2 -6M0-8-8 34.6 1
1/8 -400-8-2 1.06 1/2 8 1/4 -8M0-8-4 30.6 16.2 6.4 11/16
1/4 -400-8-4 1.17 11/16 1/8 -10M0-8-2 31.5 11/16
1/4 0.60 0.19 10 17.2 7.9
3/8 -400-8-6 1.25 13/16 1/4 -10M0-8-4 33.5 13/16
1/2 -400-8-8 1.36 1 1/4 -12M0-8-4 36.0 13/16
12 22.8 9.5
1/8 -500-8-2 1.13 9/16 1/2 -12M0-8-8 38.8 1
5/16 0.64 0.25
1/4 -500-8-4 1.20 11/16 16 1/2 -16M0-8-8 39.5 24.4 12.7 1 1/16
1/8 -600-8-2 1.20 5/8
1/4 -600-8-4 1.23 11/16
3/8 0.66 0.28
3/8 -600-8-6 1.31 13/16
1/2 -600-8-8 1.42 1
1/4 -810-8-4 1.42 13/16
1/2 3/8 -810-8-6 1.42 0.90 0.41 13/16
1/2 -810-8-8 1.53 1
3/8 -1010-8-6 1.50 15/16
5/8 0.96 0.50
1/2 -1010-8-8 1.57 1 1/16
1/2 -1210-8-8 1.57 1 1/16
3/4 0.96 0.62
3/4 -1210-8-12 1.76 1 3/8
7/8 3/4 -1410-8-12 1.76 1.02 0.72 1 3/8
3/4 -1610-8-12 1.93 1 3/8
1 1.23 0.88
1 -1610-8-16 2.11 1 11/16 Refer to Installation Instructions, beginning on page 69.
Gaugeable Tube Fittings and Adapter Fittings 39
45° Elbows
FITTINGS
Male NPT
TUBE
A Basic
F flat Dimensions
Tube NPT Ordering
OD Size Number A D E➀ F
Dimensions, in.
1/8 -400-5-2
D 1/4 0.97 0.60 0.19 1/2
1/4 -400-5-4
E 1/8 -600-5-2 1.10 0.19 5/8
3/8 1/4 -600-5-4 1.10 0.66 0.28 5/8
3/8 -600-5-6 1.15 0.28 13/16
3/8 -810-5-6 0.38
1/2 1.26 0.90 13/16
1/2 -810-5-8 0.41
3/4 3/4 -1210-5-12 1.33 0.96 0.62 1 1/16
1 1 -1610-5-16 1.59 1.23 0.88 1 3/8
➀ The E dimension is the minimum nominal opening. These fittings may
have a larger opening at the pipe/straight thread end.
D
rO
as U
➀ The E dimension is the minimum nominal opening. These fittings may have a larger
opening at the pipe/straight thread end.
Tees
FITTINGS
Unions
TUBE
D F flat
Ax
Ax
A
Union
Basic Basic
Dimensions Dimensions
Tube Ordering Tube Ordering
OD Number A Ax D E F OD Number A Ax D E F, in.
Dimensions, in. Dimensions, mm
1/16 -100-3 1.40 0.70 0.34 0.05 3/8 2 -2M0-3 44.7 22.3 12.9 1.7 3/8
1/8 -200-3 1.76 0.88 0.50 0.09 3/8 3 -3M0-3 44.7 22.3 12.9 2.4 3/8
3/16 -300-3 1.92 0.96 0.54 0.12 7/16 4 -4M0-3 50.8 25.4 13.7 2.4 1/2
1/4 -400-3 2.12 1.06 0.60 0.19 1/2 6 -6M0-3 53.9 27.0 15.3 4.8 1/2
5/16 -500-3 2.34 1.17 0.64 0.25 5/8 8 -8M0-3 59.7 29.9 16.2 6.4 5/8
3/8 -600-3 2.40 1.20 0.66 0.28 5/8 10 -10M0-3 63.0 31.5 17.2 7.9 11/16
1/2 -810-3 2.84 1.42 0.90 0.41 13/16 12 -12M0-3 72.0 36.0 22.8 9.5 13/16
5/8 -1010-3 3.06 1.53 0.96 0.50 1 14 -14M0-3 77.6 38.8 24.4 11.1 1
3/4 -1210-3 3.14 1.57 0.96 0.62 1 1/16 15 -15M0-3 77.6 38.8 24.4 11.9 1
7/8 -1410-3 3.52 1.76 1.02 0.72 1 3/8 16 -16M0-3 77.6 38.8 24.4 12.7 1
1 -1610-3 3.86 1.93 1.23 0.88 1 3/8 18 -18M0-3 79.6 39.8 24.4 15.1 1 1/16
1 1/8 B-1810-3 4.34 2.17 1.23 0.97 1 11/16 20 -20M0-3 89.3 44.6 26.0 15.9 1 3/8
1 1/4 -2000-3 5.34 2.67 1.62 1.09 1 11/16 22 -22M0-3 89.3 44.6 26.0 18.3 1 3/8
1 1/2 -2400-3 6.20 3.10 1.97 1.34 2 25 -25M0-3 98.3 49.1 31.3 21.8 1 3/8
2 -3200-3 8.44 4.22 2.66 1.81 2 3/4 -28M0-3 128 64.0 36.6 21.8 41 mm
28
B-28M0-3 103 51.4 31.6 24.6 1 11/16
30 -30M0-3 140 69.9 39.6 26.2 46 mm
32 -32M0-3 145 72.3 42.0 28.6 46 mm
38 -38M0-3 168 84.0 49.4 33.7 55 mm
50 -50M0-3 211 106 65.0 45.2 2 3/4
Tees
FITTINGS
Unions Reducing Union (Metric)
TUBE
Basic
Tube OD Dimensions
Ordering
T Tx Number A Ax D Dx E F, in.
T
Dimensions, mm
3 -3M0-3-3M-6M 49.3 26.9 12.9 15.3 2.4 1/2
Ax D E F flat
Dx
8 -8M0-3-8M-6M 59.9 29.0 16.2 15.3 4.8 5/8
6
10 -10M0-3-10M-6M 63.0 29.7 17.2 15.3 4.8 11/16
Tx 12 -12M0-3-12M-6M 72.0 31.8 22.8 15.3 4.8 13/16
A
15 -15M0-3-15M-12M 77.7 38.9 24.4 22.8 9.5 1
16 -16M0-3-16M-12M 77.6 38.9 24.4 22.8 9.5 1
18 12 -18M0-3-18M-12M 79.8 39.9 24.4 22.8 9.5 1 1/16
22 -22M0-3-22M-12M 89.4 44.7 26.0 22.8 9.5 1 3/8
25 -25M0-3-25M-12M 98.0 44.7 31.3 22.8 9.5 1 3/8
Reducing Union
E F flat
Basic
Tube OD Dimensions
Ordering
T Tx
T Tx Number A Ax Ay D Dx E F
Dx Dimensions, in.
D
Ax 3/8 1/4 -600-3-4-6 2.34 1.20 1.14 0.66 0.60 0.19 5/8
T
Ax Ay
A
E F flat Basic
Tube OD Dimensions
Ordering
T Tx Number A Ax Ay D Dx E F
T Tx
Dimensions, in.
Dx 1/2 -810-3-6-6 2.73 1.42 1.31 0.90 0.66 0.28 13/16
Ay D
5/8 3/8 -1010-3-6-6 2.95 1.53 1.42 0.96 0.66 0.28 1
3/4 -1210-3-6-6 3.03 1.57 1.46 0.96 0.66 0.28 1 1/16
Tx
Ax Ay
A
F flat Dx
Basic
Tube OD Dimensions
Ordering
T Tx T Tx Tx1 Number A Ax Ay Ay1 D Dx Dx1 E F
Dimensions, in.
5/8 1/2 -1010-3-8-6 3.06 1.53 1.53 1.42 0.96 0.90 1
Ay1 D E
3/4 1/2 3/8 -1210-3-8-6 3.14 1.57 1.57 1.46 0.96 0.90 0.66 0.28 1 1/16
Dx1 1 3/4 -1610-3-12-6 3.69 1.93 1.76 1.65 1.23 0.96 1 3/8
Tx1
Ax Ay
A
Tees
FITTINGS
E NPT Basic
Dimensions
Tube Size Ordering
OD in. Number A D E➀ F, in. H
Dimensions, in.
1/8 -200-3TTM 1.86 7/16 0.70
D 1/8 0.50 0.09
H F flat 1/4 -200-3-4TTM 1.94 1/2 0.92
3/16 1/8 -300-3TTM 1.92 0.54 0.12 7/16 0.70
1/8 -400-3TTM 0.74
A 1/4 2.12 0.60 0.19 1/2
1/4 -400-3-4TTM 0.92
5/16 1/8 -500-3TTM 2.34 0.64 0.19 5/8 0.82
1/4 -600-3TTM 2.40 5/8 1.00
3/8 0.66 0.28
3/8 -600-3-6TTM 2.62 13/16 1.11
3/8 -810-3TTM 0.38 1.11
1/2 2.84 0.90 13/16
1/2 -810-3-8TTM 0.41 1.30
5/8 1/2 -1010-3TTM 3.06 0.96 0.47 1 1.41
3/4 3/4 -1210-3TTM 3.14 0.96 0.62 1 1/16 1.45
Dimensions, mm
1/8 -6M0-3TTM 18.8
6 53.9 15.3 4.8 1/2
1/4 -6M0-3-4TTM 23.4
1/8 -8M0-3TTM 4.8 20.8
8 59.7 16.2 5/8
1/4 -8M0-3-4TTM 6.4 25.4
10 1/4 -10M0-3TTM 67.0 17.2 7.1 13/16 26.2
3/8 -12M0-3TTM 9.5 28.2
12 1/4 -12M0-3-4TTM 72.0 22.8 7.1 13/16 28.2
1/2 -12M0-3-8TTM 9.5 33.0
16 1/2 -16M0-3TTM 77.6 24.4 11.9 1 35.8
➀ The E dimension is the minimum nominal opening. These fittings may have a larger
opening at the pipe/straight thread end.
Adapter Tee
A Adapter Tees
Ax
D Basic
F Tube OD Dimensions
E
Ordering
T Tx Number A Ax D E F H
T
Dimensions, in.
Tx 1/4 -400-3-4TAA 2.06 1.00 0.60 0.17 1/2 1.00
H 1/4
3/8 -600-3-4TAA 2.28 1.08 0.66 0.17 5/8 1.08
3/8 -600-3-6TAA 2.34 1.14 0.66 0.27 5/8 1.14
3/8
1/2 -810-3-6TAA 2.67 1.25 0.90 0.27 13/16 1.25
1/2 1/2 -810-3-8TAA 3.09 1.59 0.90 0.37 15/16 1.59
FITTINGS
A Adapter Branch Tees
TUBE
Ax
D
F Basic
T Tube OD Dimensions
Ordering
T Tx Number A Ax D E F H
Dimensions, in.
H 1/4 1/4 -400-3-4TTA 2.12 1.06 0.60 0.17 1/2 1.00
3/8 3/8 -600-3-6TTA 2.40 1.20 0.66 0.27 5/8 1.14
1/2 1/2 -810-3-8TTA 3.00 1.50 0.90 0.37 15/16 1.59
Tx
E
Adapter Run Tee
A Adapter Run Tees
Ax
D Basic
F
Tube OD Dimensions
T E Ordering
T Tx Number A Ax D E F
Dimensions, in.
Tx 1/4 -400-3-4TAT 2.06 1.06 0.60 0.17 1/2
1/4
Ax 3/8 -600-3-4TAT 2.28 1.20 0.66 0.17 5/8
3/8 -600-3-6TAT 2.34 1.20 0.66 0.27 5/8
3/8
1/2 -810-3-6TAT 2.67 1.42 0.90 0.27 13/16
1/2 1/2 -810-3-8TAT 3.09 1.50 0.90 0.37 15/16
Double Run Adapter Tee
Run, NPT (TMT)
NPT Basic
Dimensions
Tube Size Ordering
E OD in. Number A Ax D E➀ F, in.
Dimensions, in.
D F flat 1/8 -200-3TMT 1.63 0.93 7/16
Ax 1/8 0.50 0.09
1/4 -200-3-4TMT 1.89 0.97 1/2
3/16 1/8 -300-3TMT 1.66 0.96 0.54 0.12 7/16
1/8 -400-3TMT 1.80
Ax 1/4 1.06 0.60 0.19 1/2
1/4 -400-3-4TMT 1.98
A
5/16 1/8 -500-3TMT 1.99 1.17 0.64 0.19 5/8
1/4 -600-3TMT 2.20 1.20 5/8
3/8 0.66 0.28
3/8 -600-3-6TMT 2.42 1.31 13/16
3/8 -810-3TMT 2.53 0.38
1/2 1.42 0.90 13/16
1/2 -810-3-8TMT 2.72 0.41
5/8 1/2 -1010-3TMT 2.88 1.50 0.96 0.47 15/16
3/4 3/4 -1210-3TMT 3.02 1.57 0.96 0.62 1 1/16
Dimensions, mm
1/8 -6M0-3TMT 45.8
6 27.0 15.3 4.8 1/2
1/4 -6M0-3-4TMT 50.3
8 1/4 -8M0-3-4TMT 55.3 29.9 16.2 6.4 5/8
1/4 -12M0-3-4TMT 64.2 7.1
12 36.0 22.8 13/16
1/2 -12M0-3-8TMT 69.0 9.5
16 1/2 -16M0-3TMT 73.1 38.0 24.4 11.9 15/16
➀ The E dimension is the minimum nominal opening. These fittings may have a larger
opening at the pipe/straight thread end.
44 Tube Fittings
Tees
FITTINGS
E F flat
SAE/MS Basic
Dimensions
Tube Thread Ordering
OD Size Number A Ax D E➀ F Fx H U
Dimensions, in.
D 1/4 7/16-20 -400-3TTS 2.24 1.12 0.60 0.19 1/2 9/16 1.12 0.65
H
Fx flat
3/8 9/16-18 -600-3TTS 2.52 1.26 0.66 0.28 5/8 11/16 1.27 0.79
1/2 3/4-16 -810-3TTS 2.96 1.48 0.90 0.41 13/16 7/8 1.49 1.01
O-ring
3/4 1 1/16-12 -1210-3TTS 3.26 1.63 0.96 0.62 1 1/16 11/4 1.92 1.44
U
washer OD 1 1 5/16-12 -1610-3TTS 3.98 1.99 1.23 0.88 1 3/8 1 1/2 2.11 1.73
Ax
A 1 1/4 1 5/8-12 -2000-3TTS 5.34 2.67 1.62 1.09 1 11/16 1 7/8 2.29 2.16
1 1/2 1 7/8-12 -2400-3TTS 6.14 3.07 1.97 1.34 2 2 1/8 2.45 2.45
SAE/MS positionable fittings are available in
carbon steel and stainless steel only. 2 2 1/2-12 -3200-3TTS 8.44 4.22 2.66 1.81 2 3/4 2 3/4 2.77 3.16
Adapts to SAE J1926/1 and ISO 11926‑1 ➀ The E dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/
straight thread boss. straight thread end.
E F flat ISO
Thread Basic Dimensions
Tube Size Ordering
OD in. Number A Ax D E➀ F, in. Fx, in. H U
Dimensions, in.
D 1/8 -400-3TTR 2.12 1.06 0.16 1/2 9/16 1.04 0.60
H 1/4 0.60
Fx flat 1/4 -400-3-4TTR 2.28 1.14 0.19 5/8 3/4 1.27 0.80
3/8 1/4 -600-3TTR 2.40 1.20 0.66 0.23 5/8 3/4 1.27 0.80
O-ring
3/8 -810-3TTR 2.84 1.42 0.31 13/16 7/8 1.46 0.96
1/2 0.90
U 1/2 -810-3-8TTR 3.00 1.50 0.41 15/16 1 1/16 1.71 1.16
retainer OD
Ax
5/8 1/2 -1010-3TTR 3.00 1.50 0.96 0.47 15/16 1 1/16 1.71 1.16
A 3/4 -1210-3TTR 0.62 1 3/8 1.92 1.43
3/4 3.14 1.57 0.96 1 1/16
1/2 -1210-3-8TTR 0.47 1 1/16 1.78 1.16
Tube ports are identical.
1 1 -1610-3TTR 3.86 1.93 1.23 0.78 1 3/8 1 5/8 2.11 1.92
See page 9 for thread specifications.
Dimensions, mm
1/8 -6M0-3TTR 53.9 27.0 4.0 1/2 9/16 26.4 15.2
6 15.3
1/4 -6M0-3-4TTR 58.0 29.0 4.8 5/8 3/4 32.2 20.3
1/8 -8M0-3TTR 57.7 4.0 9/16 9/16 28.4 15.2
8 30.0 16.2
1/4 -8M0-3-4TTR 59.7 5.9 5/8 3/4 32.3 20.3
10 1/4 -10M0-3TTR 67.0 33.5 17.2 5.9 13/16 3/4 35.1 20.3
3/8 -12M0-3TTR 72.0 36.1 7.9 13/16 7/8 37.1 24.4
12 22.8
1/2 -12M0-3-8TTR 76.1 38.1 9.5 5/16 1 1/16 43.4 29.5
➀ The E dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/
straight thread end.
Tees
FITTINGS
Male Positionable Run, ISO/BSP Parallel Thread (TRT)
TUBE
E F flat Fx flat
ISO
U Thread Basic
Dimensions
retainer Tube Size Ordering
OD OD in. Number A Ax D E➀ F, in. Fx, in. U
D Dimensions, in.
Ax O-ring 1/8 -400-3TRT 2.10 1.06 0.16 1/2 9/16 0.60
1/4 0.60
1/4 -400-3-4TRT 2.41 1.14 0.19 5/8 3/4 0.80
3/8 1/4 -600-3TRT 2.47 1.20 0.66 0.23 5/8 3/4 0.80
Ax 3/8 -810-3TRT 2.88 1.42 0.31 13/16 7/8 0.96
A 1/2 0.90
1/2 -810-3-8TRT 3.21 1.50 0.41 15/16 1 1/16 1.16
See page 9 for thread specifications. 5/8 1/2 -1010-3TRT 3.21 1.50 0.96 0.47 15/16 1 1/16 1.16
3/4 -1210-3TRT 3.49 0.62 1 3/8 1.43
3/4 1.57 0.96 1 1/16
1/2 -1210-3-8TRT 3.35 0.47 1 1/16 1.16
1 1 -1610-3TRT 4.04 1.93 1.23 0.78 1 3/8 1 5/8 1.82
Dimensions, mm
1/8 -6M0-3TRT 53.4 27.0 4.0 1/2 9/16 15.2
6 15.3
1/4 -6M0-3-4TRT 61.2 29.0 4.8 5/8 3/4 20.3
1/8 -8M0-3TRT 56.3 28.8 4.0 9/16 9/16 15.2
8 16.2
1/4 -8M0-3-4TRT 62.1 29.9 6.4 5/8 3/4 20.3
10 1/4 -10M0-3TRT 68.6 33.5 17.2 5.9 13/16 3/4 20.3
3/8 -12M0-3TRT 73.1 36.0 7.9 13/16 7/8 24.4
12 22.8
1/2 -12M0-3-8TRT 81.5 38.0 9.5 15/16 1 1/16 29.5
➀ The E dimension is the minimum nominal opening. These fittings may have a larger opening at the
pipe/straight thread end.
Tees
FITTINGS
E NPT Basic
Dimensions
Tube Size Ordering
OD in. Number A D E F, in. H
Dimensions, in.
1/8 1/8 -200-3TTF 1.94 0.50 0.09 1/2 0.75
H
D F flat 1/8 -400-3TTF 2.12 1/2 0.75
1/4 0.60 0.19
1/4 -400-3-4TTF 2.34 11/16 0.88
A 1/4 -600-3TTF 2.46 11/16 0.88
3/8 3/8 -600-3-6TTF 2.62 0.66 0.28 13/16 0.88
1/2 -600-3-8TTF 2.84 1 1.12
1/4 -810-3-4TTF 2.84 13/16 0.88
1/2 3/8 -810-3TTF 2.84 0.90 0.41 13/16 0.88
1/2 -810-3-8TTF 3.06 1 1.12
5/8 1/2 -1010-3TTF 3.06 0.96 0.50 1 1.12
3/4 3/4 -1210-3TTF 3.52 0.96 0.62 1 3/8 1.25
3/4 -1610-3-12TTF 3.86 1 3/8 1.25
1 1.23 0.88
1 -1610-3TTF 4.22 1 11/16 1.50
Dimensions, mm
1/8 -6M0-3TTF 53.9 1/2 19.0
6 15.3 4.8
1/4 -6M0-3-4TTF 59.5 11/16 22.4
1/8 -8M0-3TTF 59.7 5/8 19.0
8 16.2 6.4
1/4 -8M0-3-4TTF 61.2 11/16 22.4
10 1/4 -10M0-3TTF 67.0 17.2 7.9 13/16 22.4
1/4 -12M0-3-4TTF 72.0 13/16 22.4
12 3/8 -12M0-3TTF 72.0 22.8 9.5 13/16 22.4
1/2 -12M0-3-8TTF 77.7 1 28.4
16 1/2 -16M0-3TTF 77.6 24.4 12.7 1 28.4
Cross
Union Basic
Dimensions
Tube Ordering
OD Number A D E F, in.
Dimensions, in.
E 1/8 -200-4 1.76 0.50 0.09 3/8
1/4 -400-4 2.12 0.60 0.19 1/2
A
5/16 -500-4 2.34 0.64 0.25 5/8
3/8 -600-4 2.40 0.66 0.28 5/8
F flat D
1/2 -810-4 2.84 0.90 0.41 13/16
3/4 -1210-4 3.14 0.96 0.62 1 1/16
1 -1610-4 3.86 1.23 0.88 1 3/8
A
Dimensions, mm
3 -3M0-4 44.7 12.9 2.4 3/8
6 -6M0-4 53.9 15.3 4.8 1/2
8 -8M0-4 59.7 16.2 6.4 5/8
10 -10M0-4 67.0 17.2 7.9 13/16
12 -12M0-4 72.0 22.8 9.5 13/16
16 -16M0-4 74.0 24.4 12.7 15/16
18 -18M0-4 76.6 24.4 15.1 1 1/16
20 -20M0-4 89.3 26.0 15.9 1 3/8
22 -22M0-4 89.4 26.0 18.3 5/8
25 -25M0-4 98.3 31.3 21.8 1 3/8
FITTINGS
E minimum opening
TUBE
F flat
B G
C
A
Tube Adapters
Solve Alignment Problems and Reduce Inventories
FITTINGS
TUBE
Swagelok tube adapters can help eliminate difficult alignment problems and
100
reduce inventories. Swagelok tube adapters can be used with any Swagelok tube
50 5 150
fittings in this catalog. So, stocking union elbows and union tees in various sizes
- BW
10
and materials—along with commonly used Swagelok adapters—eliminates the
0 14
need for stocking special elbows and tees.
0 200
Typical Alignment Problem
When installing pipe elbows or tees, it is often difficult to align the fitting with the
desired run.
Tube Adapters
FITTINGS
Male
TUBE
F flat
F flat
E E
A
A
1 in./25 mm and under Over 1 in./25 mm
Tube Adapters
SWAGELOK MALE TUBE ADAPTER ISO PARALLEL THREADS (RP) CUTAWAY-MS-01-140 C-PH-1061A-DIM
FITTINGS
Male
TUBE
F flat F flat
F flat
E E E
A
A A
1 in./25 mm and under Over 1 in./25 mm
ISO/BSP parallel gaskets are available. See page 60. ISO/BSP parallel gaskets are available. See page 60.
ISO ISO
Thread Basic Thread Basic
Dimensions Dimensions
Tube Size Ordering Tube Size Ordering
OD in. Number A E➀ F OD in. Number A E➀ F
Dimensions, in. Dimensions, mm
1/8 -2-TA-1-2RS 1.25 9/16 1 -28-MTA-1-16RP➁ 72.7 19.8 41
1/8 0.08
1/4 -2-TA-1-4RS 1.43 3/4 1 1/4 -28-MTA-1-20RP➁ 77.3 22.5 50
28
1/8 -4-TA-1-2RS 1.35 0.16 9/16 1 B-28-MTA-1-16RP 65.8 19.8 1 5/8 in.
1/4
1/4 -4-TA-1-4RS 1.53 0.17 3/4 1 1/4 B-28-MTA-1-20RP 71.1 22.6 50
1/4 -6-TA-1-4RS 1.59 0.23 3/4 30 1 1/4 -30-MTA-1-20RP➁ 81.1 24.3 50
3/8
3/8 -6-TA-1-6RS 1.62 0.27 7/8 32 1 1/4 -32-MTA-1-20RP➁ 82.1 26.5 50
1/4 -8-TA-1-4RS 1.85 0.23 3/4 38 1 1/2 -38-MTA-1-24RP➁ 94.5 31.8 55
1/2 3/8 -8-TA-1-6RS 1.88 0.31 7/8
1/2 -8-TA-1-8RS 1.96 0.37 1 1/16 ➀ The E dimension is the minimum nominal opening. These fittings may
have a larger opening at the pipe/straight thread end.
3/4 3/4 -12-TA-1-12RS 2.20 0.58 1 5/16
➁ Furnished with nut and preswaged ferrules.
1 1 -16-TA-1-16RS 2.59 0.80 1 5/8
Dimensions, mm
1/8 -6-MTA-1-2RS 34.3 4.0 14
6
1/4 -6-MTA-1-4RS 38.9 4.1 19
8 1/4 -8-MTA-1-4RS 39.6 5.6 19
1/4 -10-MTA-1-4RS 40.4 5.9 19
10 3/8 -10-MTA-1-6RS 41.1 7.1 22
1/2 -10-MTA-1-8RS 43.2 7.1 27
1/4 -12-MTA-1-4RS 47.0 5.9 19
12 3/8 -12-MTA-1-6RS 47.8 7.9 22
1/2 -12-MTA-1-8RS 49.8 8.8 27
1/2 -18-MTA-1-8RS 51.3 11.9 27
18
3/4 -18-MTA-1-12RS 55.9 13.9 35
1 -28-MTA-1-16RS➁ 71.9 19.8 41
1 1/4 -28-MTA-1-20RS➁ 75.4 22.5 50
28
1 B-28-MTA-1-16RS 65.8 19.8 1 5/8 in.
1 1/4 B-28-MTA-1-20RS 69.3 22.6 50
30 1 1/4 -30-MTA-1-20RS➁ 79.8 24.3 50
32 1 1/4 -32-MTA-1-20RS➁ 80.8 26.5 50
38 1 1/2 -38-MTA-1-24RS➁ 91.9 31.6 55
➀ The E dimension is the minimum nominal opening. These fittings may
have a larger opening at the pipe/straight thread end.
➁ Furnished with nut and preswaged ferrules.
Tube Adapters
FITTINGS
Male
TUBE
F flat
O-ring F flat
F flat O-ring
O-ring
E E E
A
A
A
1 in./25 mm and under Over 1 in./25 mm See page 22 for mounting dimensions.
Adapts to SAE J1926/1 and ISO 11926-1 straight thread boss.
F flat
37°
AN Thread
AN
Tube Basic
Dimensions
Tube Flare Thread Ordering
OD Size Size Number A E➀ F
Dimensions, in.
1/4 1/4 7/16-20UNJF-3 -4-TA-1-4AN 1.46 0.17 1/2
1/4 7/16-20UNJF-3 -6-TA-1-4AN 1.53 0.17 1/2
3/8
3/8 9/16-18UNJF-3 -6-TA-1-6AN 1.56 0.27 5/8
1/2 1/2 3/4-16UNJF-3 -8-TA-1-8AN 1.91 0.37 13/16
3/4 3/4 1 1/16-12UNJ-3 -12-TA-1-12AN 2.21 0.58 1 1/8
1 1 1 5/16-12UNJ-3 -16-TA-1-16AN 2.58 0.80 1 3/8
➀ The E dimension is the minimum nominal opening. These fittings may have a larger
opening at the pipe/straight thread end.
Tube Adapters
FITTINGS
Male Pipe Weld
TUBE
37.5° Pipe Basic
Dimensions
Tube Weld Ordering
OD Size Number A E J
E J Dimensions, in.
1/4 1/4 -4-TA-1-4W 1.14 0.17 0.540
3/8 1/2 -6-TA-1-8W 1.46 0.27 0.840
A
1/2 -8-TA-1-8W 1.66 0.840
1/2 0.37
3/4 -8-TA-1-12W 1.68 1.050
3/4 3/4 -12-TA-1-12W 1.87 0.58 1.050
Wall thickness at weld end is based on schedule 80 pipe.
Female
F flat
F flat
E E
A
A
Tube Adapters
FITTINGS
Female
TUBE
F flat F flat
A A
ISO ISO
Thread Basic Thread Basic
Dimensions Dimensions
Tube Size Ordering Tube Size Ordering
OD in. Number A E F OD in. Number A E F
Dimensions, in. Dimensions, in.
1/8 1/8 -2-TA-7-2RP 1.17 0.08 9/16 1/4 1/4 -4-TA-7-4RG 1.39 0.17 3/4
1/8 -4-TA-7-2RP 1.25 9/16 3/8 3/8 -6-TA-7-6RG 1.55 0.26 15/16
1/4 0.17
1/4 -4-TA-7-4RP 1.50 3/4 1/2 1/2 -8-TA-7-8RG 1.80 0.28 1 1/16
1/4 -6-TA-7-4RP 1.55 3/4 Dimensions, mm
3/8 0.27
3/8 -6-TA-7-6RP 1.57 15/16
1/4 -6-MTA-7-4RG 35.3 19
3/8 -8-TA-7-6RP 1.78 15/16 6 3/8 -6-MTA-7-6RG 38.4 4.1 24
1/2 0.38
1/2 -8-TA-7-8RP 2.02 1 1/16 1/2 -6-MTA-7-8RG 42.9 27
Dimensions, mm 1/4 -8-MTA-7-4RG 33.0 5.5 19
1/8 -6-MTA-7-2RP 32.0 14 8 3/8 -8-MTA-7-6RG 38.9 5.6 24
6 4.1
1/4 -6-MTA-7-4RP 37.8 19 1/2 -8-MTA-7-8RG 43.7 5.6 27
12 1/2 -12-MTA-7-8RP 49.8 8.8 27 1/4 -10-MTA-7-4RG 34.5 5.5 19
10 3/8 -10-MTA-7-6RG 36.1 6.5 24
1/2 -10-MTA-7-8RG 41.1 7.1 27
1/4 -12-MTA-7-4RG 40.1 5.5 19
F flat 12 3/8 -12-MTA-7-6RG 44.7 6.5 24
1/2 -12-MTA-7-8RG 48.8 7.0 27
ISO/BSP parallel thread
(RJ) fittings are available in 16 1/2 -16-MTA-7-8RG 49.0 7.0 27
E stainless steel only. 18 1/2 -18-MTA-7-8RG 49.3 7.0 27
ISO/BSP parallel gaskets
and O‑rings are available.
See page 60.
A
74° F flat
ISO
Thread
Dimensions
Tube Size Ordering
OD in. Number A E F AN Thread
Dimensions, in.
AN
1/4 1/4 SS-4-TA-7-4RJ 1.39 0.17 3/4 Tube Basic
3/8 3/8 SS-6-TA-7-6RJ 1.55 0.26 15/16 Tube Flare Ordering
1/2 1/2 SS-8-TA-7-8RJ 1.94 0.28 1 1/16 OD Size Number F
Dimensions, mm Dimensions, in.
1/4 SS-6-MTA-7-4RJ 35.3 19 1/8 -200-A-2ANF 3/8
1/8
6 3/8 SS-6-MTA-7-6RJ 38.6 4.1 24 1/4 -200-A-4ANF 9/16
1/2 SS-6-MTA-7-8RJ 42.9 27 1/4 1/4 -400-A-4ANF 9/16
1/4 SS-8-MTA-7-4RJ 33.0 5.5 19 3/8 3/8 -600-A-6ANF 11/16
8 3/8 SS-8-MTA-7-6RJ 39.4 5.6 24 1/2 1/2 -810-A-8ANF 7/8
1/2 SS-8-MTA-7-8RJ 43.7 5.6 27
3/4 3/4 -1210-A-12ANF 1 1/4
1/4 SS-10-MTA-7-4RJ 34.5 5.5 19
10 3/8 SS-10-MTA-7-6RJ 36.1 6.5 24
1/2 SS-10-MTA-7-8RJ 41.1 7.1 27
1/4 SS-12-MTA-7-4RJ 40.1 5.5 19
12 3/8 SS-12-MTA-7-6RJ 44.7 6.5 24
1/2 SS-12-MTA-7-8RJ 48.8 7.0 27
FITTINGS
TUBE
SS
A - 2 0 D
B C 0 - 1
E - 2
F RT
G
SS - 2 0 0 - 1 - 2 RT
A Material C Series F Second End Connection Size
A = Aluminum 0 =Fractional 1/16 to 3/8 in. and Add a size designator from the list at
B = Brass 1 1/4 to 2 in. left for the second end connection or if
HC = Alloy C-276 1 = Fractional 1/2 to 1 1/8 in. the fitting is a reducing union.
INC = Alloy 600 3 = HC 3/4 in. and 1 in. with
M = Alloy 400 advanced geometry ferrules G Second End Connection Type
S = Carbon steel M = Millimeter tube size Add a second end connection type
SS = 316 stainless steel To order a female Swagelok tube fitting, add F. designator as needed.
6ELT = High-temperature Example: SS-1F0-1-1. AN =37° male AN flare
316 stainless steel ANF =37° female AN flare
D Component
T = PTFE BT =Bored-through fitting
TI = Titanium 0 = Fitting F =Female thread
6MO = 6-Moly 1 = Body KN =Knurled nut, nylon ferrules
625 = Alloy 625 E Fitting Type KT =Knurled nut, PTFE ferrules
825 = Alloy 825 1 = Male connector M =Metric tube end
2507 = Alloy 2507 2 = 90° male elbow OR =O-seal connection
3 = Tee, union PR =ISO/BSP positionable parallel
4 = Cross, union pipe thread
B Size (Tube OD)
5 = 45° male elbow RG =ISO/BSP parallel pipe thread
Fractional, in. Metric, mm
6 = Union (gauge)
1 = 1/16 2 = 2
7 = Female connector RJ =ISO/BSP parallel pipe thread
2 = 1/8 3 = 3
8 = Female elbow (Japanese gauge)
3 = 3/16 4 = 4
9 = Elbow, union RP =ISO/BSP parallel pipe thread
4 = 1/4 6 = 6
11 = Bulkhead male connector RS =ISO/BSP parallel pipe thread
5 = 5/16 8 = 8
61 = Bulkhead union RT =ISO/BSP tapered pipe thread
6 = 3/8 10 = 10
71 = Bulkhead female connector ST =Straight thread with O-ring
8 = 1/2 12 = 12
A = Adapter (for SAE/MS)
10 = 5/8 14 = 14
C = Cap W =Male pipe weld/tube socket
12 = 3/4 15 = 15
P = Plug weld
14 = 7/8 16 = 16
16 = 1 18 = 18 PC = Port connector
18 = 1 1/8 20 = 20 R = Reducer
20 = 1 1/4 22 = 22 R1 = Bulkhead reducer
24 = 1 1/2 25 = 25 2R = Reducing elbow
32 = 2 28 = 28 TFT = Tee, female run
32 = 32 TMT = Tee, male run
38 = 38 TRT =Tee, ISO/BSP parallel male
50 = 50 positionable run
TST =Tee, straight thread with
O‑ring male positionable run
TTF = Tee, female branch
TTM = Tee, male branch
TTR =Tee, ISO/BSP parallel male
positionable branch
TTS =Tee, straight thread with
O‑ring male positionable
branch
SS
A - B
2 - TA
C - D
1 - E
4 RT
F
SS - 2 - TA - 1 - 4 RT
A Material C Component E Second End Connection Size
A = Aluminum TA = Fractional tube adapter Add a size designator from the list at
B = Brass MTA = Metric tube adapter left for the second end connection.
HC = Alloy C-276
INC = Alloy 600 D Adapter Type F Second End Connection Type
M = Alloy 400 1 = Male adapter Add a second end connection type
S = Carbon steel 7 = Female adapter designator as needed.
SS = 316 stainless steel AN =37° male AN flare
6ELT = High-temperature ANF =37° female AN flare
316 stainless steel RG =ISO/BSP parallel pipe thread
T = PTFE (gauge)
TI = Titanium RJ =ISO/BSP parallel pipe thread
6MO = 6-Moly (Japanese gauge)
625 = Alloy 625 RP =ISO/BSP parallel pipe thread
825 = Alloy 825 RS =ISO/BSP parallel pipe thread
2507 = Alloy 2507 RT =ISO/BSP tapered pipe thread
ST =Straight thread with O-ring
(for SAE/MS)
B Size (Tube OD) W =Male pipe weld/tube socket
Fractional, in. Metric, mm weld
1 = 1/16 2 = 2
2 = 1/8 3 = 3
3 = 3/16 4 = 4
4 = 1/4 6 = 6
5 = 5/16 8 = 8
6 = 3/8 10 = 10
8 = 1/2 12 = 12
10 = 5/8 14 = 14
12 = 3/4 15 = 15
14 = 7/8 16 = 16
16 = 1 18 = 18
18 = 1 1/8 20 = 20
20 = 1 1/4 22 = 22
24 = 1 1/2 25 = 25
32 = 2 28 = 28
32 = 32
38 = 38
50 = 50
Gaugeable Tube Fittings and Adapter Fittings 57
Replacement Parts
To order, add a material designator from the How to Order table on page 14.
FITTINGS
TUBE
Nuts Female
G flat
Basic Basic
Dimensions Dimensions
Tube Ordering Tube Ordering
OD Number G L OD Number G L
Dimensions, in. Dimensions, mm
L
1/16 -102-1 5/16 0.31 2 -2M2-1 12 11.9
1/8 -202-1 7/16 0.47 3 -3M2-1 12 11.9
3/16 -302-1 1/2 0.47 4 -4M2-1 12 11.9
1/4 -402-1 9/16 0.50 6 -6M2-1 14 12.7
5/16 -502-1 5/8 0.53 8 -8M2-1 16 13.5
3/8 -602-1 11/16 0.56 10 -10M2-1 19 15.1
1/2 -812-1 7/8 0.69 12 -12M2-1 22 17.4
5/8 -1012-1 1 0.69 14 -14M2-1 25 17.4
3/4 -1212-1 1 1/8 0.69 15 -15M2-1 25 17.4
7/8 -1412-1 1 1/4 0.69 16 -16M2-1 25 17.4
1 -1612-1 1 1/2 0.81 18 -18M2-1 30 17.4
1 1/4 -2002-1 1 7/8 1.25 20 -20M2-1 32 17.4
1 1/2 -2402-1 2 1/4 1.50 22 -22M2-1 32 17.4
2 -3202-1 3 2.06 25 -25M2-1 38 20.6
-28M2-1 46 30.6
28
B-28M2-1 45 20.6
30 -30M2-1 50 32.7
32 -32M2-1 50 34.4
38 -38M2-1 60 40.6
50 -50M2-1 3 in. 52.3
G flat
Knurled Female
The Swagelok knurled nut tube fitting provides a leak-tight seal without the
use of inserts on most wall thicknesses of polyethylene tubing. Inserts may be
required for larger sizes.
L
To set the ferrules on the tubing, initial connections must be made with a
wrench, tightening the nut one and one-quarter turns from finger-tight (three-
quarter turn for 1/16, 1/8 and 3/16 in.; 2, 3, and 4 mm fittings). Leak-tight
connections may be reassembled with finger-tight assembly.
To order a knurled nut, add K to the female nut basic ordering number.
Example: B-402-1K
To order a knurled nut on an assembled fitting with nylon ferrules, add KN to
the fitting ordering number.
Example: SS-400-1-2KN
To order a knurled nut on an assembled fitting with PTFE ferrules, add KT to
the fitting ordering number.
Example: SS-400-1-2KT
Male
G flat
Basic Basic
Dimensions Dimensions
Tube Ordering Tube Ordering
OD Number G L OD Number G L
Dimensions, in. Dimensions, mm
L
1/16 -1F2-1GC 1/4 0.38 10 -10MF2-1 22 22.1
1/8 -2F2-1GC 3/8 0.53 12 -12MF2-1 24 22.1
For use in female Swagelok
end connections. 1/4 -4F2-1 1/2 0.62
1/2 -8F2-1 15/16 0.87
58 Tube Fittings
Replacement Parts
SWAGELOK FRONT FERRULE CUTAWAY-MS-01-140 C-PH-0056-BDM
To order, add a material designator from the How to Order table on page 14.
FITTINGS
TUBE
Ferrules
Front Back
Basic Basic Basic Basic
Tube Ordering Tube Ordering Tube Ordering Tube Ordering
OD Number OD Number OD Number OD Number
Dimensions, in. Dimensions, mm Dimensions, in. Dimensions, mm
1/16 -103-1 2 -2M3-1 1/16 -104-1 2 -2M4-1
1/8 -203-1 3 -3M3-1 1/8 -204-1 3 -3M4-1
3/16 -303-1 4 -4M3-1 3/16 -304-1 4 -4M4-1
1/4 -403-1 6 -6M3-1 1/4 -404-1 6 -6M4-1
5/16 -503-1 8 -8M3-1 5/16 -504-1 8 -8M4-1
3/8 -603-1 10 -10M3-1 3/8 -604-1 10 -10M4-1
1/2 -813-1 12 -12M3-1 1/2 -814-1 12 -12M4-1
5/8 -1013-1 14 -14M3-1 5/8 -1014-1 14 -14M4-1
3/4 -1213-1 15 -15M3-1 3/4 -1214-1 15 -15M4-1
7/8 -1413-1 16 -16M3-1 7/8 -1414-1 16 -16M4-1
1 -1613-1 18 -18M3-1 1 -1614-1 18 -18M4-1
1 1/4 -2003-1➀ 20 -20M3-1 1 1/4 -2004-1➀ 20 -20M4-1
1 1/2 -2403-1➀ 22 -22M3-1 1 1/2 -2404-1➀ 22 -22M4-1
2 -3203-1➀ 25 -25M3-1 2 -3204-1➀ 25 -25M4-1
➀ Over 1 in. and over 28 -28M3-1➀ ➀ Over 1 in. and over 28 -28M4-1➀
25 mm stainless steel 30 -30M3-1➀ 25 mm stainless steel 30 -30M4-1➀
front ferrules are PFA back ferrules are PFA
coated. To order silver- 32 -32M3-1➀ coated. To order back 32 -32M4-1➀
plated front ferrules, add 38 -38M3-1➀ ferrules without PFA 38 -38M4-1➀
-BL to the basic ordering coating, add -WC to the
number. 50 -50M3-1➀ basic ordering number. 50 -50M4-1➀
Example: SS-2003-1BL Example: SS-2004-1WC
Gaugeable Tube Fittings and Adapter Fittings 59
Replacement Parts
FITTINGS
Nut-Ferrule Set and Ferrule Set
TUBE
Use of Nuts and Ferrules
Using Swagelok nuts and ferrules on tube fittings or valves with tube end connections
requires critical interaction of precision parts.
Swagelok nuts and ferrules are sold as replacement parts for use with only Swagelok
bodies, fittings, valves, and hose products.
Sets are shown with arbors. One arbor holds five nut-ferrule sets or ten ferrule sets.
The nut-ferrule set contains one nut, one back ferrule, and The ferrule set contains one front ferrule and one back ferrule.
one front ferrule. To order, add a material designator to the basic ordering number.
To order, add a material designator to the basic ordering number. Please order ferrule sets in multiples of ten.
Please order nut-ferrule sets in multiples of five. Example: SS-100-SET
Example: SS-400-NFSET
Replacement Parts
FITTINGS
Replacement Parts
FITTINGS
O-Rings
TUBE
Buna N Buna N
(O-Seal Straight Threads) (O-Seal Pipe Threads)
O-ring hardness is 70 durometer. O-ring hardness is 70 durometer.
Swagelok hydraulic swaging units preswage Swagelok ferrules onto tubing prior to
assembly and provide Swagelok tube fitting connections that are 100 % gaugeable
upon initial installation. Multihead hydraulic and air-actuated hydraulic swaging units:
■ Place no initial strain on nut or fitting body threads or on body seal surfaces
■ Are available with interchangeable fractional and metric tooling
■ Fit neatly in a rugged plastic carrying case
■ Reduce assembly and installation time and operator error.
FITTINGS
Hydraulic Swaging Units
TUBE
MHSU Ordering Information Accessories Tooling Kits
Select an ordering number. Additional and replacement gap Up to 1 in./25 mm
inspection gauges are available. See
Ordering Numbers
page 67. Tube Ordering
See the table below for replacement OD Number
MHSU Unit
retaining rings, pliers, and chamfer Dimensions, in.
Up to 1 in./
MS-MHSU-U-E blocks. 1/2 MS-MHSUT-U-810-M
25 mm sizes
1 in./25 mm 5/8 MS-MHSUT-U-1010-M
MS-MHSU-O-E
and over sizes 3/4 MS-MHSUT-U-1210-M
MHSU Unit Ordering Number
MHSU Unit with Tooling Kit 7/8 MS-MHSUT-U-1410-M
Fractional Retaining Ring
MS-MHSU-U-E-FKIT-M 1 MS-MHSUT-U-1610-M
up to 1 in. sizes Up to 1 in./
MS-MHSU-N5000-200-H
Fractional 1 in. 25 mm sizes Alloy 2507 Tubing
MS-MHSU-O-E-FKIT-M 1 in./25 mm
and over sizes 5/8 MS-MHSUT-O-2507-1010-M
MS-MHSU-N5000-315-H
Metric up to and over sizes
MS-MHSU-U-E-MKIT-M 3/4 MS-MHSUT-O-2507-1210-M
25 mm sizes Retaining Ring Pliers
Dimensions, mm
Metric 25 to Up to 1 in./
MS-MHSU-O-E-MKIT-M MS-MHSU-0504 12 MS-MHSUT-U-12M0-M
38 mm➀ sizes 25 mm sizes
➀ 50 mm tooling available separately. 1 in./25 mm 14 MS-MHSUT-U-14M0-M
MS-MHSU-0700
and over sizes 15 MS-MHSUT-U-15M0-M
Support Base 16 MS-MHSUT-U-16M0-M
Add -B to the ordering number. 18 MS-MHSUT-U-18M0-M
Chamfer Ordering
Examples: MS-MHSU-U-E-B Blocks Number 20 MS-MHSUT-U-20M0-M
MS-MHSU-U-E-FKIT-M-B in. 22 MS-MHSUT-U-22M0-M
1/2 MS-CB-810 25 MS-MHSUT-U-25M0-M
Operating Instructions
5/8 MS-CB-1010
MHSU ordering numbers include 1 in./25 mm and Over
English-language instructions. For 3/4 MS-CB-1210
other languages, visit swagelok.com. 7/8 MS-CB-1410 Tube Ordering
1 MS-CB-1610 OD Number
mm Dimensions, in.
See the Swagelok Multihead Hydraulic 1 MS-MHSUT-O-1610-M
12 MS-CB-12M0
Swaging Unit (MHSU) Setup and 1 1/4 MS-MHSUT-O-2000-M
Operating Instructions, MS‑12‑37, for 14 MS-CB-14M0
15 MS-CB-15M0 1 1/2 MS-MHSUT-O-2400-M
information about using the MHSU.
16 MS-CB-16M0 2 MS-MHSUT-O-3200-M
18 MS-CB-18M0 Dimensions, mm
20 MS-CB-20M0 25 MS-MHSUT-O-25M0-M
22 MS-CB-22M0 28 MS-MHSUT-O-28M0-M
25 MS-CB-25M0 30 MS-MHSUT-O-30M0-M
32 MS-MHSUT-O-32M0-M
38 MS-MHSUT-O-38M0-M
50 MS-MHSUT-O-50M0-M
64 Tube Fittings
Air-Actuated
Hydraulic Swaging Unit (AHSU)
■ Requires only one unit with
interchangeable tooling to swage
1/4 to 1/2 in. and 6 to 12 mm
Swagelok tube fitting ferrule sizes
■ Requires no threading of nut on or off
the tooling
Accessories
Additional and replacement gap
inspection gauges are available. See
page 67.
FITTINGS
Preswaging Tools
TUBE
For Swagelok tube fitting installations in close
quarters, the Swagelok preswaging tool is a
convenient accessory.
Features
■ Preswages ferrules onto the tube
■ Enables the installer to work in a more open, safe area
■ Makes it possible to complete the installation by following
retightening instructions for Swagelok tube fittings
Wrenches
TUBE
Features Features
■ Allows user to hold fitting body firmly and precisely ■ 11 fractional and metric sizes are available.
■ Is available in a variety of sizes ■ 1/12 turn ratchet facilitates use in close quarters.
■ Fits and carries easily in tool box, pouch, or belt ■ Heavy-duty construction includes:
■ Head and handle constructed of stainless steel ■ heat-treated, black oxide-plated steel handle
■ Features a cushioned vinyl grip and generous gripping area ■ black-oxide plated steel jaws
for handle ■ stainless steel spring and fasteners.
■ Holds tee in various orientations
For Swagelok Gaugeable Union Tees and Crosses Tube Ordering Wrench
OD Number Length
Tube OD Ordering Number Tee Cross
1/4 in. and 6 mm MS-TW-4 ✓ ✓ Dimensions, in.
1/8 MS-RW-200
5/16 and 3/8 in. and 8 mm MS-TW-6 ✓ ✓ 5.38
3/16 MS-RW-300
10 mm MS-TW-10M ✓ ➀
1/4 MS-RW-400
1/2 in. and 12 mm MS-TW-8 ✓ ✓
5/16 MS-RW-500 7.25
➀ Use MS-TW-8 on 10 mm Swagelok crosses.
3/8 MS-RW-600
1/2 MS-RW-810 10.1
Dimensions, mm
3 MS-RW-3M0 136
6 MS-RW-6M0
8 MS-RW-8M0 184
10 MS-RW-10M0
12 MS-RW-12M0 257
FITTINGS
Gap Inspection Gauges
TUBE
Swagelok gap inspection gauges assure the installer or
inspector that the fitting has been sufficiently pulled up
on initial installation, whether using a Swagelok multihead
hydraulic swaging unit (MHSU), page 62, or air-actuated
hydraulic swaging unit (AHSU), page 64, or wrench
tightening. All metal Swagelok tube fittings are gaugeable,
with the exception of a few forged bodies in aluminum.
screw
(included) “U” drive screw
By using the bulkhead retainer,
one person can tighten the jam F E Bulkhead retainer
nut on side A for initial bulkhead
Bulkhead fitting installation
fitting installation. Now tubing utilizing bulkhead retainer
can be connected to side A and B A
by one person with one wrench,
Side A Side B
because the bulkhead retainer Jam Body
D nut hex
acts as a backup wrench.
B 1/8 in.
Gaugeability
On initial installation, the Swagelok gap inspection gauge
FITTINGS
TUBE
assures the installer or inspector that a fitting has been
sufficiently tightened.
Position the Swagelok gap inspection gauge next to the gap between the nut and body.
If the gauge will not enter the gap, the If the gauge will enter the gap,
fitting is sufficiently tightened. additional tightening is required.
Installation Instructions
Swagelok tube fittings 1 in./25 mm and smaller can be installed quickly, easily, and reliably with simple hand tools.
Over 1 in./25 mm sizes require use of a hydraulic swaging unit to swage the ferrules onto the tubing.
Installation Instructions
FITTINGS
These instructions apply both to traditional fittings and to fittings with the advanced back-ferrule geometry.
Fully insert the tube into the fitting and Mark the nut at the 6 o’clock position. While holding the fitting body steady,
against the shoulder; rotate the nut tighten the nut one and one-quarter
finger-tight. turns to the 9 o’clock position.
High-pressure applications and high For 1/16, 1/8, and 3/16 in.; 2, 3, and
safety-factor systems: Further tighten 4 mm tube fittings, tighten the nut only
the nut until the tube will not turn by three-quarters turn to the 3 o’clock
hand or move axially in the fitting. position.
Reassembly—All Sizes
You may disassemble and reassemble Swagelok tube fittings many times.
• Always depressurize the system before disassembling a Swagelok tube fitting.
Prior to disassembly, mark the tube at Insert the tube with preswaged ferrules While holding the fitting body steady,
the back of the nut; mark a line along into the fitting until the front ferrule rotate the nut with a wrench to the
the nut and fitting body flats. seats against the fitting body. previously pulled-up position, as
Use these marks to ensure that you Over 1 in./25 mm sizes: If needed, indicated by the marks on the tube
return the nut to the previously pulled- reapply lubricant lightly to the body and flats. At this point, you will feel
up position. threads and the rear surface of the a significant increase in resistance.
back ferrule. Tighten the nut slightly.
• Do not use the Swagelok gap inspection gauge with reassembled fittings.
Installation Instructions
FITTINGS
Caps and Plugs
TUBE
Caps Plugs
See Swagelok tube While holding fitting body steady, tighten the plug one-quarter turn from
fitting installation and the finger-tight position.
reassembly, page 70. For 1/16, 1/8, and 3/16 in.; 2, 3, and 4 mm tube fittings, tighten the plug one-eighth turn.
For over 1 in./25 mm tube fittings, tighten the plug one-quarter turn.
• Do not use the Swagelok gap inspection gauge with plug assemblies.
Reassembly
You may disassemble and reassemble Swagelok plugs many times. Make subsequent
connections by slightly tightening with a wrench after snugging the nut by hand.
Port Connectors
Connect the machined ferrule end before connecting the tube adapter end.
Machined Ferrule End Tube Adapter End
1. Remove the nut and ferrules from the Swagelok end 5. Insert the tube adapter until it rests firmly on the shoulder
KOLEGAWS
connection. Discard the ferrules. of the Swagelok tube fitting body. Finger-tighten the nut.
SWAGELOK
SWAGELOK
KOLEGAWS
Discard
port connector.
Over 1 in./25 mm
sizes: The nut is 1 in./25 mm
preassembled on and under Over 1 in./25 mm
12
SWAGELOK
end connection
and finger-tighten 6
the nut.
4. While holding
fitting body steady,
tighten the nut
one-quarter turn.
For 1/16, 1/8, and
3/16 in.; 2, 3, and
For 1/16, 1/8, and 3/16 in.; 2, 3, and 4 mm tube fittings,
4 mm tube fittings,
tighten the nut three-quarters turn to the 3 o’clock
tighten the nut
position.
one-eighth turn.
For preswaged over 1 in./25 mm and over tube fittings,
• Do not use the tighten the nut one-half turn to the 12 o’clock position.
Swagelok gap
inspection gauge • Do not use the Swagelok gap inspection gauge
with machined with preswaged tube adapter connections over
ferrule ends. 1 in./25 mm.
Reassembly Reassembly
You may disassemble and reassemble Swagelok port See Swagelok tube fitting reassembly, page 70.
connectors many times. Make subsequent connections by
slightly tightening with a wrench after snugging the nut by hand.
72 Tube Fittings
Installation Instructions
FITTINGS
1. Turn the positionable end into the female fitting until the metal backup washer
contacts the face of the fitting.
2. Turn the positionable end out of the female fitting (not more than one turn) until
Lock nut Backup the Swagelok tube fitting end is positioned properly.
washer 3. While holding fitting body steady, tighten the lock nut until the metal backup
washer contacts the face of the fitting.
Tube Adapters
Fig. 1 Up to 1 in./25 mm Over 1 in./25 mm
1. Install the end opposite the tube Swagelok tube adapters over 1 in./
adapter end (Fig. 1). 25 mm are furnished with nuts and
2. Insert the tube adapter into the preswaged ferrules.
Female pipe port
on existing equipment Swagelok tube fitting. Make sure that To assemble, follow steps 2 through
Fig. 2
the tube adapter rests firmly on the 5 of the Swagelok tube fittings over
shoulder of the tube fitting body and 1 in./25 mm assembly instructions,
that the nut is finger-tight (Fig. 2). page 70.
3. Mark the nut at the 6 o’clock
position.
• Do not use the Swagelok gap
inspection gauge with preswaged
4. While holding fitting body steady, tube adapter connections over
tighten the nut one and one- 1 in./25 mm.
quarter turns to the 9 o’clock
position. Reassembly
For 1/16, 1/8, and 3/16 in.; 2, 3, See Swagelok tube fitting reassembly,
and 4 mm tube fittings, tighten the page 70.
nut only three-quarters turn to the
3 o’clock position.
Reassembly instructions:
12 12 12 12 There are a maximum of 10 re-assemblies per SAE J514.
Installation Instructions
FITTINGS
Weld Fittings
TUBE
Welding Precautions for Swagelok Tube Fittings with Weld End Connections
1. Remove the nut and ferrules. 5. Complete the weld.
2. Turn a Swagelok tube fitting plug or another nut onto the 6. Remove the plug or nut and replace the nut and ferrules.
fitting so that it is finger-tight. This protects the threads
and sealing components. • Caution: When welding carbon steel fittings, the heat
often removes the protective oil from the threads.
3. Provide a suitable heat sink to dissipate the heat.
It is important to apply another lubricant, such as
4. Tack weld at four positions 90° apart to hold the fitting in Goop™ thread lubricant.
place and to ensure alignment and concentricity of the
components.
Installation Instructions
Preswaging Tool
Fig. 1 1. Install the Swagelok nut and 7. Remove the tube with preswaged
ferrules onto the preswaging tool. ferrules from the preswaging tool.
2. Insert the tube into the preswaging If the tube sticks in the preswaging
tool. tool, remove the tube by gently
rocking it back and forth. Do not
3. Make sure that the tube rests firmly
turn the tube (Fig. 2).
on the shoulder of the preswaging
tool body and that the nut is finger- 8. Insert the tube with preswaged
tight. ferrules into the fitting until the front
Fig. 2 ferrule seats against the fitting body.
4. Mark the nut at the 6 o’clock
position. 9. While holding the fitting body
steady, rotate the nut with a
5. While holding the preswaging tool
wrench to the previously pulled-up
steady, tighten the nut one and
position; at this point, you will feel
one-quarter turns to the 9 o’clock
a significant increase in resistance.
position.
Fig. 3 10. Tighten the nut slightly (Fig. 3).
For 1/16, 1/8, and 3/16 in.; 2, 3,
and 4 mm tube fittings, tighten the • Do not use the Swagelok gap
nut only three-quarters turn to the inspection gauge with fittings
3 o’clock position (Fig. 1). that were assembled using the
6. Loosen the nut. preswaging tool.
74 Tube Fittings
Warranty Information Micro-Fit, Nupro, Snoop, Sno-Trik, SWAK, VCO, VCR, Ultra-Torr,
Whitey—TM Swagelok Company
15-7 PH—TM AK Steel Corp.
Swagelok products are backed by The Swagelok Limited AccuTrak, Beacon, Westlock—TM Tyco International Services
Lifetime Warranty. For a copy, visit swagelok.com or contact Aflas—TM Asahi Glass Co., Ltd.
ASCO, El-O-Matic—TM Emerson
your authorized Swagelok representative. AutoCAD—TM Autodesk, Inc.
CSA—TM Canadian Standards Association
Crastin, DuPont, Kalrez, Krytox, Teflon, Viton—TM E.I. duPont
Nemours and Company
DeviceNet—TM ODVA
Dyneon, Elgiloy, TFM—TM Dyneon
Elgiloy—TM Elgiloy Specialty Metals
Safe Product Selection FM —TM FM Global
Grafoil—TM GrafTech International Holdings, Inc.
When selecting a product, the total system design must Honeywell, MICRO SWITCH—TM Honeywell
be considered to ensure safe, trouble-free performance. MAC—TM MAC Valves
Microsoft, Windows—TM Microsoft Corp.
Function, material compatibility, adequate ratings, NACE—TM NACE International
proper installation, operation, and maintenance are the PH 15-7 Mo, 17-7 PH—TM AK Steel Corp
picofast—Hans Turck KG
responsibilities of the system designer and user. Pillar—TM Nippon Pillar Packing Company, Ltd.
Raychem—TM Tyco Electronics Corp.
Sandvik, SAF 2507—TM Sandvik AB
Simriz—TM Freudenberg-NOK
SolidWorks—TM SolidWorks Corporation
Caution: Do not mix or interchange parts with those of UL—Underwriters Laboratories Inc.
Xylan—TM Whitford Corporation
other manufacturers. © 2019 Swagelok Company