Professional Documents
Culture Documents
2016 Nissan Titan - Brake Control System
2016 Nissan Titan - Brake Control System
BRC
A
B
SECTION
BRAKE CONTROL SYSTEM C
E
CONTENTS
VDC/TCS/ABS VDC/TCS/ABS : TCS Function ................................32 BRC
VDC/TCS/ABS : ABS Function ................................33
PRECAUTION ............................................... 4 VDC/TCS/ABS : EBD Function ...............................35
cardiagn.com
VDC/TCS/ABS : TSA Function ................................36 G
PRECAUTIONS ................................................... 4
Precaution for Supplemental Restraint System HILL DESCENT CONTROL FUNCTION ...................38
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- HILL DESCENT CONTROL FUNCTION : System
SIONER" ................................................................... 4 Description ...............................................................38 H
Precaution for Work .................................................. 4
HILL START ASSIST FUNCTION .............................39
Precaution for Procedure without Cowl Top Cover...... 5
HILL START ASSIST FUNCTION : System De-
Precaution for Brake System .................................... 5 I
Precaution for Brake Control System ........................ 5 scription ...................................................................39
Precaution for Harness Repair .................................. 6 BRAKE LIMITED SLIP DIFFERENTIAL (BLSD)
FUNCTION .................................................................40 J
PREPARATION ............................................ 8 BRAKE LIMITED SLIP DIFFERENTIAL (BLSD)
PREPARATION ................................................... 8 FUNCTION : System Description ............................40
Special Service Tool ................................................. 8 DIAGNOSIS SYSTEM [ABS ACTUATOR K
Commercial Service Tool .......................................... 8
AND ELECTRIC UNIT (CONTROL UNIT)] ....... 43
SYSTEM DESCRIPTION .............................. 9 CONSULT Function (ABS) ......................................43
L
COMPONENT PARTS ........................................ 9 ECU DIAGNOSIS INFORMATION .............. 48
Component Parts Location ........................................ 9
ABS ACTUATOR AND ELECTRIC UNIT
Component Description ........................................... 10 M
ABS Actuator and Electric Unit (Control Unit) ......... 10
(CONTROL UNIT) ............................................. 48
Reference Value ......................................................48
Wheel Sensor and Sensor Rotor ............................ 11
Fail-safe ...................................................................51
Stop Lamp Switch ................................................... 12
DTC Inspection Priority Chart ..................................54 N
Steering Angle Sensor ............................................ 12
DTC Index ...............................................................55
Yaw Rate/Side/Decel G Sensor .............................. 12
Brake Fluid Level Switch ......................................... 12 WIRING DIAGRAM ...................................... 56
Parking Brake Switch .............................................. 12 O
VDC OFF Switch ..................................................... 13 BRAKE CONTROL SYSTEM ........................... 56
Hill Descent Control Switch ..................................... 13 Wiring Diagram ........................................................56
P
SYSTEM .............................................................14 BASIC INSPECTION ................................... 66
VDC/TCS/ABS ........................................................... 14 DIAGNOSIS AND REPAIR WORK FLOW ....... 66
VDC/TCS/ABS : System Diagram ........................... 14 Work Flow ................................................................66
VDC/TCS/ABS : System Description ...................... 14 Diagnostic Work Sheet ............................................67
VDC/TCS/ABS : Fail-safe ....................................... 24
VDC/TCS/ABS : VDC Function ............................... 29
cardiagn.com
C1105, C1106, C1107, C1108 WHEEL SEN- C1155 BRAKE FLUID LEVEL SWITCH .......... 126
SOR .................................................................... 79 DTC Description .................................................... 126
DTC Description ..................................................... 79 Diagnosis Procedure ............................................. 126
Diagnosis Procedure .............................................. 80 Component Inspection .......................................... 129
C1109 POWER AND GROUND SYSTEM ......... 86 C1160 INCOMPLETE DECEL G SENSOR
DTC Description ..................................................... 86 CALIBRATION ................................................. 130
Diagnosis Procedure .............................................. 86 DTC Description .................................................... 130
C1111 ABS MOTOR, MOTOR RELAY SYS- Diagnosis Procedure ............................................. 130
TEM .................................................................... 88 C1164, C1165 CV SYSTEM ............................. 132
DTC Description ..................................................... 88 DTC Description .................................................... 132
Diagnosis Procedure .............................................. 88 Diagnosis Procedure ............................................. 132
C1115 WHEEL SENSOR ................................... 91 C1166, C1167 SV SYSTEM ............................. 134
DTC Description ..................................................... 91 DTC Description .................................................... 134
Diagnosis Procedure .............................................. 91 Diagnosis Procedure ............................................. 134
C1116 STOP LAMP SWITCH ............................ 98 C1170 VARIANT CODING ............................... 136
DTC Description ..................................................... 98 DTC Description .................................................... 136
Diagnosis Procedure .............................................. 99 Diagnosis Procedure ............................................. 136
Component Inspection ...........................................102
C1187 DIFFERENTIAL LOCK CONTROL
C1118 TRANSFER CONTROL UNIT .............. 104 UNIT .................................................................. 137
DTC Logic ..............................................................104 DTC Logic ............................................................. 137
Diagnosis Procedure .............................................104 Diagnosis Procedure ............................................. 137
C1120, C1122, C1124, C1126 ABS IN VALVE C118E ACCUMULATOR .................................. 138
SYSTEM ........................................................... 105 DTC Logic ............................................................. 138
DTC Description ....................................................105 Diagnosis Procedure ............................................. 138
Diagnosis Procedure .............................................106
U1000 CAN COMM CIRCUIT ........................... 139
C1121, C1123, C1125, C1127 ABS OUT DTC Description .................................................... 139
VALVE SYSTEM .............................................. 107 Diagnosis Procedure ............................................. 139
DTC Description ....................................................107
Diagnosis Procedure .............................................108 POWER SUPPLY AND GROUND CIRCUIT .... 140
Diagnosis Procedure ............................................. 140
C1130 ENGINE SIGNAL ................................. 109
DTC Description ....................................................109 PARKING BRAKE SWITCH ............................. 143
VDC OFF INDICATOR LAMP .......................... 149 SENSOR ROTOR ............................................ 162
Component Function Check .................................. 149
FRONT SENSOR ROTOR ....................................... 162 BRC
Diagnosis Procedure ............................................. 149 FRONT SENSOR ROTOR : Removal and Instal-
SLIP INDICATOR LAMP .................................. 150 lation - Front Sensor Rotor .................................... 162
cardiagn.com
Component Function Check .................................. 150 REAR SENSOR ROTOR ......................................... 162 G
Diagnosis Procedure ............................................. 150 REAR SENSOR ROTOR : Removal and Installa-
tion - Rear Sensor Rotor ........................................ 162
SYMPTOM DIAGNOSIS ............................ 151
H
ABS ACTUATOR AND ELECTRIC UNIT
VDC/TCS/ABS .................................................. 151
Symptom Table ..................................................... 151
(CONTROL UNIT) ........................................... 163
Removal and Installation ....................................... 163
I
EXCESSIVE ABS FUNCTION OPERATION
MOTOR/ACCUMULATOR .............................. 164
FREQUENCY ................................................... 152
Removal and Installation ....................................... 164
Diagnosis Procedure ............................................. 152
J
STEERING ANGLE SENSOR ......................... 165
UNEXPECTED PEDAL REACTION ................ 153
Removal and Installation ....................................... 165
Diagnosis Procedure ............................................. 153
YAW RATE/SIDE/DECEL G SENSOR ........... 166 K
THE BRAKING DISTANCE IS LONG .............. 154
Exploded View ....................................................... 166
Diagnosis Procedure ............................................. 154
Removal and Installation ....................................... 166
ABS FUNCTION DOES NOT OPERATE ......... 155 L
VDC OFF SWITCH .......................................... 167
Diagnosis Procedure ............................................. 155
Exploded View ....................................................... 167
PEDAL VIBRATION OR ABS OPERATION Removal and Installation ....................................... 167
M
SOUND OCCURS ............................................ 156 HILL DESCENT CONTROL SWITCH ............. 168
Diagnosis Procedure ............................................. 156
Exploded View ....................................................... 168
VEHICLE JERKS DURING VDC/TCS/ABS Removal and Installation ....................................... 168
N
CONTROL ........................................................ 157
Diagnosis Procedure ............................................. 157
O
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000013465633
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, it is recommended that all mainte-
nance and repair be performed by an authorized NISSAN/INFINITI dealer.
• Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury
caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module,
see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
cardiagn.com
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery or batteries, and wait at least three minutes before performing any service.
Precaution for Work INFOID:0000000014082160
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
A
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc. to prevent damage to
windshield. B
D
PIIB3706J
cardiagn.com
• Do not reuse drained brake fluid. G
• Do not spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it off
immediately and wash with water if it gets on a painted surface.
• Always confirm the specified tightening torque when installing the brake pipes.
• After pressing the brake pedal more deeply or harder than normal driving, such as air bleeding, check each H
item of brake pedal. Adjust brake pedal if it is outside the standard value.
• Do not use mineral oils such as gasoline or light oil to clean. They may damage rubber parts and cause
improper operation. I
• Always loosen the brake tube flare nut with a flare nut wrench.
• Tighten the brake tube flare nut to the specified torque with a flare
nut crowfoot (A) and torque wrench (B).
• Always connect the battery terminal when moving the vehicle. J
• Turn the ignition switch OFF and disconnect the ABS actuator and
electric unit (control unit) harness connector or the battery negative
terminal before performing the work. K
• Check that no brake fluid leakage is present after replacing the
parts.
L
JPFIA0001ZZ
• Slight vibrations are felt on the brake pedal and the operation noises occur, when VDC function, TCS func-
tion, ABS function, EBD function, hill start assist function or brake limited slip differential (BLSD) function N
operates. This is not a malfunction because it is caused by VDC function, TCS function, ABS function, EBD
function, hill start assist function or brake limited slip differential (BLSD) function that is normally operated.
• When starting engine or when starting vehicle just after starting engine, brake pedal may vibrate or motor
operating noise may be heard from engine compartment. This is normal condition. O
• Brake stopping distance may become longer than models without ABS function depending on the road con-
ditions, when ABS function is operated on slippery road like rough road, gravel road or snowy road.
• When a malfunction is indicated, always collect information from the customer about conditions of occur- P
rence, estimate cause and perform operation. Check brake booster operation, brake fluid level and brake
fluid leakage, as well as electrical system.
• The optimum performance is achieved by control for VDC function, TCS function, ABS function, EBD func-
tion, hill start assist function or brake limited slip differential (BLSD) function when all of brakes, suspensions
and tires installed on the vehicle are the specified size and parts. Brake performance and controllability may
be negatively affected when other parts than the specified are installed.
• Brake stopping distance may become longer and steering stability may be negatively affected, when tires in
different size and combination or other parts than the specified are used.
Revision: March 2016 BRC-5 2016 Titan NAM
PRECAUTIONS
< PRECAUTION > [VDC/TCS/ABS]
• When a radio (including wiring), antenna and antenna lead line are located near ABS actuator and electric
unit (control unit), a malfunction or improper operation may occur for the control of VDC function, TCS func-
tion, ABS function, EBD function, hill start assist function or brake limited slip differential (BLSD) function.
• When the following items are replaced by other parts than genuine parts or modified, ABS warning lamp,
brake warning lamp and VDC warning lamp may turn ON, and the control may not operate normally for VDC
function, TCS function, ABS function, EBD function, hill start assist function or brake limited slip differential
(BLSD) function.
- Suspension component parts (shock absorber, spring, bushing and others)
- Tire and wheel (other than the specified size)
- Brake component parts (brake pad, disc rotor, brake caliper and others)
- Engine component parts (ECM, muffler and others)
- Body reinforcement component parts (rollover bar, tower bar and others)
• When suspension, tire and brake component parts are excessively worn or deteriorated and the vehicle is
driven, ABS warning lamp, brake warning lamp and VDC warning lamp may turn ON, and the control may
not operate normally for VDC function, TCS function, ABS function, EBD function, hill start assist function or
brake limited slip differential (BLSD) function.
• ABS warning lamp, brake warning lamp and VDC warning lamp may turn ON, when only front wheel or rear
wheel is rotated using a free roller. This is not a malfunction, because it is caused by wheel speed difference
between wheel that is rotated and wheel that is not rotated. In this case, perform self-diagnosis, check self-
diagnosis results, and erase memory.
• When power supply voltage is not normal, ABS warning lamp, brake warning lamp and VDC warning lamp
cardiagn.com
turn ON. ABS actuator and electric unit (control unit) stops control for VDC function, TCS function, ABS func-
tion, EBD function, hill start assist function or brake limited slip differential (BLSD) function. Ordinary brake
operates. After power supply returns to normal, ABS warning lamp, brake warning lamp and VDC warning
lamp turn OFF. The control becomes operative for VDC function, TCS function, ABS function, EBD function,
hill start assist function or brake limited slip differential (BLSD) function.
• VDC warning lamp may turn ON and VDC function or TCS function may not normally operate, when driving
on a special road the is extremely slanted (bank in a circuit course). This is not a malfunction if the status
returns to normal for VDC function or TCS function after the engine is started again. In this case, perform
self-diagnosis, check self-diagnosis results, and erase memory.
• A malfunction in yaw rate/side/decel G sensor system may be detected when the vehicle sharply turns dur-
ing a spin turn, acceleration turn or drift driving while VDC function or TCS function are OFF (VDC OFF
switch is pressed and VDC OFF indicator lamp is in ON status). This is not a malfunction if the status returns
to normal for VDC function or TCS function after the engine is started again. In this case, perform self-diag-
nosis, check self-diagnosis results, and erase memory
Precaution for Harness Repair INFOID:0000000013283845
• Solder the repair part, and wrap it with tape. [Twisted wire fray
must be 110 mm (4.33 in) or less.]
SKIB8766E
SKIB8767E
BRC
cardiagn.com
G
PREPARATION
PREPARATION
Special Service Tool INFOID:0000000013472090
The actual shape of the tools may differ from those illustrated here.
Tool number Description
(TechMate No.)
Tool name
KV991J0080 Checking operation of ABS active wheel sen-
(J-45741-A) sors
ABS active wheel sensor tester
WFIA0101E
cardiagn.com
AWJIA0483ZZ
S-NT360
PIIB1407E
SYSTEM DESCRIPTION A
COMPONENT PARTS
Component Parts Location INFOID:0000000013123909
B
BRC
cardiagn.com
G
ALFIA0708ZZ
ALFIA0709ZZ
A. Right rear wheel area B. Center console area (view with cen- C. Center of instrument panel
ter console finisher removed)
D. Right front wheel area E. Left side of engine compartment F. Brake pedal area (view with instru-
cardiagn.com
(view with ABS actuator and electric ment panel removed)
unit (control unit) removed)
G. Left side of instrument panel (view H. Left side of instrument panel I. Steering column area (view with
with combination meter removed) steering wheel removed)
ALFIA0641ZZ
Motor/Accumulator Assembly
Pump C
• Operates the pump drive according to signals from ABS actuator and electric unit (control unit) by the motor.
Motor
• Operates the motor drive according to signals from ABS actuator and electric unit (control unit). D
Accumulator
• The accumulator accumulates brake fluid conveyed by the motor and pump.
E
Motor Relay
Operates the motor ON/OFF according to signals from ABS actuator and electric unit (control unit).
Actuator Relay (Main Relay) BRC
Operates each valve ON/OFF according to signals from ABS actuator and electric unit (control unit).
cardiagn.com
ABS IN Valve and ABS OUT Valve
Increases, holds or decreases the fluid pressure of each caliper according to signals from ABS actuator and G
electric unit (control unit).
Cut Valve 1, Cut Valve 2
Shuts off the ordinary brake line from master cylinder to signals from ABS actuator and electric unit (control H
unit).
Suction Valve 1
I
Suction valve 1 switches the brake path to convey accumulator pressure to the front system, according to a
signal transmitted from the ABS actuator and electric unit (control unit).
Suction Valve 2 J
Suction valve 2 releases accumulator pressure, according to a signal transmitted from the ABS actuator and
electric unit (control unit).
Accumulator Pressure Sensor K
The accumulator pressure sensor detects brake fluid pressure accumulated in the accumulator and conveys
the detected result to the ABS actuator and electric unit (control unit).
Master Cylinder Pressure Sensor L
Detects the brake fluid pressure of master cylinder part and transmits a signal to ABS actuator and electric unit
(control unit).
Wheel Sensor and Sensor Rotor INFOID:0000000013123912 M
NOTE:
• Wheel sensor and sensor rotor is integrated in wheel hub assembly. N
• Never measure resistance and voltage value using a tester because sensor is active sensor.
• Downsize and weight reduction is aimed. IC for detection portion
and magnet for sensor rotor are adopted.
• Power supply is supplied to detection portion so that magnetic field O
line is read. Magnetic field that is detected is converted to current
signal.
• When sensor rotor rotates, magnetic field changes. Magnetic field P
change is converted to current signals (rectangular wave) and is
transmitted to ABS actuator and electric unit (control unit). Change
of magnetic field is proportional to wheel speed.
JPFIC0131GB
JSFIA1143ZZ
cardiagn.com
• Steering wheel rotation direction
ALFIA0591ZZ
ALFIA0633ZZ
Detects the brake fluid level in reservoir tank and transmits converted electric signal from ABS actuator and
electric unit (control unit), when brake fluid level is the specified level or less.
Parking Brake Switch INFOID:0000000013123917
ALFIA0634ZZ
A
• The operation of the VDC OFF switch enables the arbitrary switching of the VDC function between stop sta-
tus and standby status. The status of the function is indicated by the VDC OFF indicator lamp. (ON: Non-
operational status, OFF: Standby status) B
- VDC function
- TCS function
• VDC OFF indicator lamp turns OFF (standby status) when the
engine is started again after it is stopped once while VDC OFF C
indicator lamp is ON (non-operational status).
ALFIA0430ZZ
BRC
Hill Descent Control Switch INFOID:0000000013135977
cardiagn.com
• The hill descent control system will help maintain vehicle speed on
steeper downhill grades. Hill descent control will provide braking G
allowing the driver to concentrate on steering while reducing the
burden and accelerator operation.
H
ALFIA0432ZZ
J
cardiagn.com
ALFIA0710GB
• The system switches fluid pressure of each brake caliper to increase, to hold or to decrease according to
signals from control unit in ABS actuator and electric unit (control unit). This control system is applied to
VDC function, TCS function, ABS function and EBD function.
• Fail-safe function is available for each function and is activated by each function when system malfunction
occurs.
INPUT AND OUTPUT SIGNALS
Major signal transmission between each unit via communication lines is shown in the following table:
BRC
cardiagn.com
G
ALFIA0667GB
M
Name Not activated When depressing brake pedal
Cut valve 1 Power supply is not supplied (open) Power supply is not supplied (open)
N
Cut valve 2 Power supply is not supplied (open) Power supply is not supplied (open)
Suction valve 1 Power supply is not supplied (close) Power supply is not supplied (close)
Suction valve 2 Power supply is not supplied (close) Power supply is not supplied (close) O
ABS IN valve Power supply is not supplied (open) Power supply is not supplied (open)
ABS OUT valve Power supply is not supplied (close) Power supply is not supplied (close)
Each caliper (fluid pressure) — Pressure increases
P
Front RH caliper
• Pressurized brake fluid from accumulator is supplied to front RH caliper through master cylinder part, cut
valve 1 and ABS IN valve.
Front LH caliper
• Pressurized brake fluid from accumulator is supplied to front LH caliper through master cylinder part, cut
valve 1 and ABS IN valve.
Revision: March 2016 BRC-15 2016 Titan NAM
SYSTEM
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
Rear RH caliper
• Pressurized brake fluid from accumulator is supplied to rear RH caliper through master cylinder part, cut
valve 2 and ABS IN valve.
Rear LH caliper
• Pressurized brake fluid from accumulator is supplied to rear LH caliper through master cylinder part, cut
valve 2 and ABS IN valve.
ABS Is Operating (When Pressure Increases)
cardiagn.com
ALFIA0668GB
Front RH caliper
• Pressurized brake fluid from accumulator is supplied to front RH caliper through master cylinder part, cut
valve 2, suction valve 1 and ABS IN valve.
Front LH caliper
• Pressurized brake fluid from accumulator is supplied to front LH caliper through master cylinder part, cut
valve 2, suction valve 1 and ABS IN valve.
Rear RH caliper
• Pressurized brake fluid from accumulator is supplied to rear RH caliper through master cylinder part, cut
valve 2 and ABS IN valve.
Rear LH caliper
• Pressurized brake fluid from accumulator is supplied to rear LH caliper through master cylinder part, cut
valve 2 and ABS IN valve.
BRC
cardiagn.com
G
H
ALFIA0669GB
Rear LH caliper
• ABS IN valve is close and fluid pressure of rear LH caliper is holds. O
ABS Is Operating (When Pressure Decreases)
cardiagn.com
ALFIA0670GB
Front RH caliper
• Being returned to reservoir tank through ABS OUT valve, fluid pressure of front RH caliper is decreased.
Front LH caliper
• Being returned to reservoir tank through ABS OUT valve, fluid pressure of front LH caliper is decreased.
Rear RH caliper
• Being returned to reservoir tank through ABS OUT valve, fluid pressure of rear RH caliper is decreased.
Rear LH caliper
• Being returned to reservoir tank through ABS OUT valve, fluid pressure of rear LH caliper is decreased.
VDC Is Operating (When Pressure Increases)
BRC
cardiagn.com
G
H
ALFIA0671GB
Front RH caliper
• Pressurized brake fluid from accumulator is supplied to front RH caliper through suction valve 2, suction
N
valve 1 and ABS IN valve. When not increasing, ABS IN valve is closed and brake fluid is not supplied to
front RH caliper.
Front LH caliper O
• Pressurized brake fluid from accumulator is supplied to front LH caliper through suction valve 2, suction
valve 1 and ABS IN valve. When not increasing, ABS IN valve is closed and brake fluid is not supplied to
front LH caliper.
P
Rear RH caliper
• Pressurized brake fluid from accumulator is supplied to rear RH caliper through suction valve 2 and ABS IN
valve. When not increasing, ABS IN valve is closed and brake fluid is not supplied to rear RH caliper.
Rear LH caliper
• Pressurized brake fluid from accumulator is supplied to rear LH caliper through suction valve 2 and ABS IN
valve. When not increasing, ABS IN valve is closed and brake fluid is not supplied to rear LH caliper.
cardiagn.com
ALFIA0672GB
Front RH caliper
• ABS IN valve is close, fluid pressure of front RH caliper is holds.
Front LH caliper
• ABS IN valve is close, fluid pressure of front LH caliper is holds.
Rear RH caliper
• ABS IN valve is close, fluid pressure of rear RH caliper is holds.
Rear LH caliper
• ABS IN valve is close, fluid pressure of rear LH caliper is holds.
VDC Is Operating (When Pressure Decreases)
BRC
cardiagn.com
G
H
ALFIA0673GB
Component Function
Operates the pump drive according to signals from ABS actuator and electric unit (control unit) by
Pump
the motor.
Motor Operates the motor drive according to signals from ABS actuator and electric unit (control unit).
Accumulator The accumulator accumulates brake fluid conveyed by the motor and pump.
Increases, holds or decreases the fluid pressure of each caliper according to signals from ABS ac-
ABS IN valve
tuator and electric unit (control unit).
Increases, holds or decreases the fluid pressure of each caliper according to signals from ABS ac-
ABS OUT valve
tuator and electric unit (control unit).
Cut valve 1 Shuts off the ordinary brake line from master cylinder to signals from ABS actuator and electric unit
Cut valve 2 (control unit).
Suction valve 1 switches the brake line to convey accumulator pressure to the front system, accord-
Suction valve 1
ing to a signal transmitted from the ABS actuator and electric unit (control unit).
Suction valve 2 releases accumulator pressure, according to a signal transmitted from the ABS ac-
Suction valve 2
tuator and electric unit (control unit).
The accumulator pressure sensor detects brake fluid pressure accumulated in the accumulator and
Accumulator pressure sensor
conveys the detected result to the ABS actuator and electric unit (control unit).
Detects the brake fluid pressure of master cylinder part and transmits a signal to ABS actuator and
cardiagn.com
Master cylinder pressure sensor
electric unit (control unit).
cardiagn.com
hill start assist function is malfunctioning ON
G
Brake limited slip differential (BLSD) function is malfunctioning ON
VDC function is operating Blinking
TCS function is operating Blinking H
cardiagn.com
tion. The Vehicle status becomes the same as models without VDC function and TCS function. However, ABS
function and EBD function are operated normally.
ABS FUNCTION
ABS warning lamp and SLIP indicator lamp in combination meter turn ON when a malfunction occurs in sys-
tem [ABS actuator and electric unit (control unit)]. The control is suspended for VDC function, TCS function,
hill start assist function and ABS function. The vehicle status becomes the same as models without VDC func-
tion, TCS function and ABS function. However, EBD function is operated normally.
NOTE:
ABS self-diagnosis sound may be heard the same as in the normal condition, because self-diagnosis is per-
formed when ignition switch turns ON and when vehicle initially starts.
EBD FUNCTION
ABS warning lamp, brake warning lamp and SLIP indicator lamp in combination meter turn ON when a mal-
function occurs in system [ABS actuator and electric unit (control unit)]. The control is suspended for VDC
function, TCS function, ABS function, hill start assist function and EBD function. The vehicle status becomes
the same as models without VDC function, TCS function, ABS function and EBD function.
cardiagn.com
normal.
G
• When power supply voltage of front wheel sensor LH is low.
• When distance between front wheel sensor LH and front wheel sensor LH rotor is
C1108 large.
• When installation of front wheel sensor LH or front wheel sensor LH rotor is not H
normal.
• When ignition voltage is 10 V or less. The following functions are sus-
C1109
• When ignition voltage is 16 V or more. pended: I
• VDC function
• TCS function
• When a malfunction is detected in motor or motor relay. • ABS function
C1111 • When a low pressure malfunction is detected in accumulator. • Hill start assist function J
• When a malfunction is detected in accumulator pressure sensor. • Hill descent control function
• EBD function
• BLSD function
K
When difference in wheel speed between any wheel and others is detected while the The following functions are sus-
C1115
vehicle is driven, because of installation of tires other than specified. pended:
• VDC function
• TCS function L
• When stop lamp switch signal is not input when brake pedal is depressed. • ABS function
C1116 • Hill start assist function
• When stop lamp switch signal is not input when stop lamp relay operates.
• Hill descent control function
• BLSD function M
The following functions are sus-
pended:
• VDC function N
• TCS function
C1118 When a malfunction is detected in transfer control unit.
• ABS function
• Hill start assist function
• Hill descent control function O
• BLSD function
The following functions are sus-
pended: P
• VDC function
• TCS function
C1120 When a malfunction is detected in front LH ABS IN valve. • ABS function
• Hill start assist function
• Hill descent control function
• EBD function
• BLSD function
cardiagn.com
• TCS function
C1123 When a malfunction is detected in front RH ABS OUT valve. • ABS function
• Hill start assist function
• Hill descent control function
• EBD function
• BLSD function
The following functions are sus-
pended:
• VDC function
• TCS function
C1124 When a malfunction is detected in rear LH ABS IN valve. • ABS function
• Hill start assist function
• Hill descent control function
• EBD function
• BLSD function
The following functions are sus-
pended:
• VDC function
• TCS function
C1125 When a malfunction is detected in rear LH ABS OUT valve. • ABS function
• Hill start assist function
• Hill descent control function
• EBD function
• BLSD function
The following functions are sus-
pended:
• VDC function
• TCS function
C1126 When a malfunction is detected in rear RH ABS IN valve. • ABS function
• Hill start assist function
• Hill descent control function
• EBD function
• BLSD function
cardiagn.com
• Hill descent control function G
• EBD function
• BLSD function
C1142 When a malfunction is detected in master cylinder pressure sensor. The following functions are sus-
H
pended.
C1143 When a malfunction is detected in steering angle sensor.
• VDC function
C1144 When neutral position adjustment of steering angle sensor is not complete. • TCS function
• Hill start assist function I
• When a malfunction is detected in yaw rate signal. • Hill descent control function
• When yaw rate signal is not continuously received for 2 seconds or more. • BLSD function
C1145
• When side G signal is not continuously received for 2 seconds or more. The following functions are sus-
• When decel G signal is not continuously received for 2 seconds or more. pended: J
• VDC function
C1146 When a malfunction is detected in side/decel G signal.
• TCS function
• When brake fluid level low signal is detected. • ABS function
C1155 K
• When an open circuit is detected in brake fluid level switch circuit. • Hill start assist function
• Hill descent control function
C1160 When calibration of yaw rate/side/decel G sensor is not complete. • BLSD function
C1164 When a malfunction is detected in cut valve 1. The following functions are sus- L
pended:
C1165 When a malfunction is detected in cut valve 2.
• VDC function
C1166 When a malfunction is detected in suction valve 1. • TCS function
• ABS function
M
• Hill start assist function
C1167 When a malfunction is detected in suction valve 2. • Hill descent control function
• EBD function N
• BLSD function
The following functions are sus-
pended:
• VDC function O
• TCS function
C1170 When the information in ABS actuator and electric unit (control unit) is not the same.
• ABS function
• Hill start assist function
P
• Hill descent control function
• BLSD function
cardiagn.com
• Hill start assist function
• Hill descent control function
• BLSD function
PROTECTION FUNCTION
The SLIP indicator lamp, ABS warning lamp and brake warning lamp turn ON and DTC “C118E” may be
detected in “Self Diagnostic Result” mode of “ABS” when the brake pedal is excessively operated, such as air
bleeding. This is not a system malfunction because this occurs due to the temporary decrease in accumulator
fluid pressure. The system returns to normal condition when the accumulator fluid pressure reaches the spec-
ified pressure with the ignition switch ON and the SLIP indicator lamp, ABS warning lamp, and brake warning
lamp turned OFF. After these steps, erase self-diagnosis results for “ABS” with CONSULT.
A
SYSTEM DIAGRAM
BRC
cardiagn.com
G
JPFIC0183GB
I
SYSTEM DESCRIPTION
• Side slip or tail slip may occur while driving on a slippery road or attempting an urgent evasive driving
maneuver. VDC function detects side slip status using each sensor when side slip or tail slip is about to J
occur and improves vehicle stability by brake control and engine output control during driving.
• In addition to ABS function, EBD function and TCS function, target side slip amount is calculated according
to steering operation amount from steering angle sensor and brake operation amount from pressure sensor.
By comparing this information with vehicle side slip amount that is calculated from yaw rate/side/decel G- K
sensor and wheel sensor information, vehicle driving conditions (conditions of understeer or oversteer) are
judged and vehicle stability is improved by brake force control on all four wheels and engine output control.
L
JPFIC0133GB
• Control unit portion automatically improves driving stability by performing brake force control as well as O
engine output control, by transmitting drive signal to actuator portion according to difference between target
side slip amount and vehicle side slip amount.
• VDC function can be switched to non-operational status (OFF) by operating VDC OFF switch. In this case,
VDC OFF indicator lamp turns ON. P
• SLIP indicator lamp is blinking while VDC function is in operation and indicates to the driver that the function
is in operation.
• Slight vibrations are felt on the brake pedal and the operation noises occur, when VDC function operates.
This is not a malfunction because it is caused by VDC function that is normally operated.
• CONSULT can be used to diagnose the system diagnosis.
• Fail-safe function is adopted. When a malfunction occurs in VDC function, the control is suspended for VDC
function and TCS function. The vehicle status becomes the same as models without VDC function and TCS
cardiagn.com
TCM communication:
• Shift position signal
Mainly transmits the following signal to ABS actuator and electric unit (control unit) via CAN
Transfer control unit*2 communication:
• Current 4WD mode signal
Mainly transmits the following signal to ABS actuator and electric unit (control unit) via CAN
Steering angle sensor communication:
• Steering angle sensor signal
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication:
Combination meter
• SLIP indicator lamp signal
• VDC OFF indicator lamp
*1: Communication line between yaw rate/side/decel G sensor and ABS actuator and electric unit (control unit)
*2: Models with 4WD
OPERATION CHARACTERISTICS
VDC Function That Prevents Oversteer Tendency
• During a cornering, brake force (brake fluid pressure) is applied on front wheel and rear wheel on the outer
side of turn. Momentum directing towards the outer side of turn is generated. Oversteer is prevented.
ALFIA0339GB
ALFIA0340GB D
VDC Function That Prevents Understeer Tendency
• During a cornering, brake force (brake fluid pressure) is applied on front wheel and rear wheel on the inner
side of turn. Momentum directing towards the inner side of turn is generated. Understeer is prevented. E
BRC
cardiagn.com
G
JPFIC0137GB H
• Applying braking during a cornering on a slippery road, when understeer tendency is judged large, engine
output is controlled as well as brake force (brake fluid pressure) of four wheels. Understeer tendency
I
decreases.
L
ALFIA0341GB
SYSTEM DIAGRAM
cardiagn.com
JPFIC0183GB
SYSTEM DESCRIPTION
• Wheel spin status of drive wheel is detected by wheel sensor of
four wheels. Engine output and transmission shift status is con-
trolled so that slip rate of drive wheels is in appropriate level. When
wheel spin occurs on drive wheel, ABS actuator and electric unit
(control unit) perform brake force control of LH and RH drive
wheels (apply brake force by increasing brake fluid pressure of
drive wheel) and decrease engine torque by engine torque control.
Wheel spin amount decreases. Engine torque is controlled to
appropriate level.
• TCS function can be switched to non-operational status (OFF) by
operating VDC OFF switch. In this case, VDC OFF indicator lamp
turns ON.
• TCS function will not operate when 4WD mode is in “4LO”.
• SLIP indicator lamp is blinking while TCS function is in operation
and indicates to the driver that the function is in operation.
• Slight vibrations are felt on the brake pedal and the operation
noises occur, when TCS function operates. This is not a malfunc-
tion because it is caused by TCS function that is normally oper-
ated.
• CONSULT can be used to diagnose the system diagnosis.
• Fail-safe function is adopted. When a malfunction occurs in TCS
function, the control is suspended for VDC function and TCS func-
tion. The vehicle status becomes the same as models without VDC
JPFIC0139GB
function and TCS function. However, ABS function, BLSD and
EBD function are operated normally. Refer to BRC-55, "DTC Index".
INPUT AND OUTPUT SIGNALS
Major signal transmission between each unit via communication lines is shown in the following table.
cardiagn.com
Steering angle sensor communication: G
• Steering angle sensor signal
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication:
Combination meter
• SLIP indicator lamp signal
H
• VDC OFF indicator lamp
*1: Communication line between yaw rate/side/decel G sensor and ABS actuator and electric unit (control unit)
*2: Models with 4WD I
J
SYSTEM DIAGRAM
JPFIC0184GB
SYSTEM DESCRIPTION
Revision: March 2016 BRC-33 2016 Titan NAM
SYSTEM
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
• By preventing wheel lock through brake force (brake fluid pressure) control that is electronically controlled by
detecting wheel speed during braking, stability during emergency braking is improved so that obstacles can
be easily bypassed by steering operation.
• During braking, control units calculate wheel speed and pseudo-vehicle speed, and transmits pressure
increase, hold or decrease signals to actuator portion according to wheel slip status.
• The following effects are obtained by preventing wheel lock during
braking:
- Vehicle tail slip is prevented during braking when driving straight.
- Understeer and oversteer tendencies are moderated during brak-
ing driving on a corner.
- Obstacles may be easily bypassed by steering operation during
braking.
• Slight vibrations are felt on the brake pedal and the operation
noises occur, when ABS function operates. This is not a malfunc-
tion because it is caused by ABS function that is normally oper-
ated.
• CONSULT can be used to diagnose the system diagnosis.
• Fail-safe function is adopted. When a malfunction occurs in ABS
function, the control is suspended for VDC function and TCS func-
tion. The vehicle status becomes the same as models without VDC
function, TCS function and ABS function. However, EBD function
cardiagn.com
is operated normally. Refer to BRC-51, "Fail-safe".
NOTE:
• To stop vehicle efficiently, ABS does not operate and ordinary
brake operates at low speed [approx. 5 to 10 km/h (3.1 to 6.2
MPH) or less, but differs subject to road conditions).
• Self-diagnosis is performed immediately after engine starts and
when vehicle initially is driven [by vehicle speed approx. 15 km/h
JPFIC0140GB
(9.3 MPH)]. Motor sounds are generated during self-diagnosis. In
addition, brake pedal may feel heavy when depressing brake pedal lightly. These symptoms are not mal-
functions.
INPUT AND OUTPUT SIGNALS
Major signal transmission between each unit via communication lines is shown in the following table.
A
SYSTEM DIAGRAM
BRC
cardiagn.com
G
ALFIA0711GB
I
SYSTEM DESCRIPTION
• By preventing rear wheel slip increase through rear wheel brake force (brake fluid pressure) control that is
electronically controlled when slight skip on front and rear wheels is detected during braking, stability during J
braking is improved.
• EBD function is expanded and developed from conventional ABS function and corrects rear wheel brake
force to appropriate level by electronic control according to load weight (number of passengers).
K
JPFIC0142GB
N
cardiagn.com
JPFIC0143GB
SYSTEM DIAGRAM
ALFIA0712GB
cardiagn.com
Major signal transmission between each unit via communication lines is shown in the following table: G
Mainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
communication:
• Accelerator pedal position signal J
ECM • Engine speed signal
Mainly receives the following signal from ABS actuator and electric unit (control unit) via CAN
communication:
• Target throttle position signal K
Mainly transmits the following signal to ABS actuator and electric unit (control unit) via CAN
TCM communication:
• Shift position signal L
Mainly transmits the following signal to ABS actuator and electric unit (control unit) via CAN
Steering angle sensor communication:
• Steering angle sensor signal M
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication:
Combination meter
• SLIP indicator lamp signal
• VDC OFF indicator lamp
N
*1: Communication line between yaw rate/side/decel G sensor and ABS actuator and electric unit (control unit)
OPERATION CHARACTERISTICS O
Trailer Sway Assist Function Prevents Tow vehicle and trailer oscillation.
ALFIA0674GB
cardiagn.com
ALFIA0435GB
cardiagn.com
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication: G
• VDC warning lamp signal
• VDC OFF indicator lamp signal
*: Communication line between yaw rate/side/decel G sensor and ABS actuator and electric unit (control unit) H
HILL START ASSIST FUNCTION
HILL START ASSIST FUNCTION : System Description INFOID:0000000013137412
I
• This function maintains brake fluid pressure so that the vehicle does not move backwards, even if brake
pedal is released to depress accelerator pedal to start the vehicle while it is stopped on an uphill slope by
depressing brake pedal. J
• This function operates when the vehicle is in stop status on a uphill slope of slope ratio 10% or more and
selector lever is in the position other than P or N.
• Hill start assist function is only for the start aid. It maintains the brake fluid pressure for approx. 2 seconds K
after releasing the brake pedal, and then decreases the pressure gradually. If the vehicle can start by the
accelerator operation, the brake is released automatically and a smooth start can be performed.
• Fail-safe function is adopted. When a malfunction occurs in hill start assist function, the control is suspended
for VDC function, TCS function, Brake assist function, hill start assist function and Brake force distribution L
function. The vehicle status becomes the same as models without VDC function, TCS function, Brake assist
function, Hill start assist function and Brake force distribution function. However, ABS function and EBD
function are operated normally. Refer to BRC-51, "Fail-safe". M
cardiagn.com
ALFIA0448GB
• LH and RH driving wheel spin is always monitored. If necessary, appropriate brake force is independently
applied to LH or RH driving wheel so that one-sided wheel spin is avoided and traction is maintained. Mainly
starting ability is improved.
• Brake limited slip differential (BLSD) function operates while VDC function is in non-operational status (OFF)
by VDC OFF switch.
BRC
cardiagn.com
G
JPFIC0183GB
L
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
M
Component Signal description
Mainly transmits the following signals to ABS actuator and electric unit (control unit) via com-
munication line*1. N
Yaw rate/side/decel G sensor • Yaw rate signal
• Side G sensor signal
• Decel G sensor signal
Mainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
O
communication.
• Accelerator pedal position signal
ECM • Engine speed signal P
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
• Target throttle position signal
Mainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
TCM communication.
• Shift position signal
cardiagn.com
ECU IDENTIFICATION
cardiagn.com
ABS actuator and electric unit (control unit) part number is displayed. G
SELF DIAGNOSTIC RESULT
Operation Procedure
H
1. Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for
approximately 1 minute.
How To Erase Self-diagnostic Result I
1. After erasing DTC memory, start engine and drive vehicle at 30 km/h (19 MPH) or more for approximately
1 minute as the final inspection, and make sure that the ABS warning lamp, VDC OFF indicator lamp,
SLIP indicator lamp and brake warning lamp turn OFF. J
CAUTION:
If memory cannot be erased, perform applicable diagnosis.
NOTE:
• When the wheel sensor malfunctions, after inspecting the wheel sensor system, the ABS warning lamp, K
SLIP indicator lamp and brake warning lamp will not turn OFF even when the system is normal unless
the vehicle is driving at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
• Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or brake fluid L
level switch operation (when brake fluid is insufficient).
• VDC OFF switch should not stay in ON position.
Display Item List M
Refer to BRC-55, "DTC Index".
DATA MONITOR
N
cardiagn.com
RR LH OUT SOL Rear LH OUT ABS solenoid (On/Off) status is dis-
– × ×
(On/Off) played.
EBD WARN LAMP
– – × Brake warning lamp (On/Off) status is displayed.
(On/Off)
STOP LAMP SW
× × × Stop lamp switch (On/Off) status is displayed.
(On/Off)
MOTOR RELAY
– × × ABS motor relay signal (On/Off) status is displayed.
(On/Off)
ACTUATOR RLY
– × × ABS actuator relay signal (On/Off) status is displayed.
(On/Off)
ABS WARN LAMP
– × × ABS warning lamp (On/Off) status is displayed.
(On/Off)
OFF LAMP
– × × VDC OFF Lamp (On/Off) status is displayed.
(On/Off)
OFF SW
× × × VDC OFF switch (On/Off) status is displayed.
(On/Off)
SLIP/VDC LAMP
– × × SLIP indicator lamp (On/Off) status is displayed.
(On/Off)
BATTERY VOLT Voltage (V) supplied to ABS actuator and electric unit
× × ×
(V) (control unit) is displayed.
GEAR Gear position (1, 2, 3, 4, 5) judged by transmission
× × ×
(1, 2, 3, 4, 5) range switch signal is displayed.
ENGINE SPEED Engine speed (rpm) judged by CAN communication
× × ×
(rpm) signal is displayed.
YAW RATE SEN Yaw rate (d/s) detected by yaw rate sensor is dis-
× × ×
(d/s) played.
R POSI SIG Reverse shift position (On/Off) judged by transmis-
– – ×
(On/Off) sion range switch signal.
N POSI SIG Shift position judged by transmission range switch
– – ×
(On/Off) signal.
CV1 Front side switch-over solenoid valve (cut valve) (On/
– – ×
(On/Off) Off) status is displayed.
CV2 Rear side switch-over solenoid valve (cut-valve) (On/
– – ×
(On/Off) Off) status is displayed.
cardiagn.com
EBD SIGNAL G
– – × EBD operation (On/Off) status is displayed.
(On/Off)
ABS SIGNAL
– – × ABS operation (On/Off) status is displayed.
(On/Off) H
TCS SIGNAL
– – × TCS operation (On/Off) status is displayed.
(On/Off)
VDC SIGNAL I
– – × VDC operation (On/Off) status is displayed.
(On/Off)
EBD FAIL SIG
– – × EBD fail signal (On/Off) status is displayed.
(On/Off) J
ABS FAIL SIG
– – × ABS fail signal (On/Off) status is displayed.
(On/Off)
TCS FAIL SIG K
– – × TCS fail signal (On/Off) status is displayed.
(On/Off)
VDC FAIL SIG
– – × VDC fail signal (On/Off) status is displayed.
(On/Off) L
CRANKING SIG The input state of the key SW START position signal
– – ×
(On/Off) is displayed.
FLUID LEV SW M
× – × Brake fluid level switch (On/Off) status is displayed.
(On/Off)
PARK BRAKE SW
× – × Park brake switch (On/Off) status is displayed.
(On/Off)
N
DLOCK SW – – × Displays differential lock mode switch position.
DLOCK CHG SW – – × Displays condition of differential lock position switch.
STP ON RLY O
– – × Stop lamp relay signal (On/Off) status is displayed.
(On/Off)
DDS SW (Note 1) Hill descent control switch status (On/Off) status is
– – ×
(On/Off) displayed. P
DDS SIG (Note 1) Hill descent control operation (On/Off) status is dis-
– – ×
(On/Off) played.
USS SIG (Note 2)
– – × Hill start assist operation (On/Off) status is displayed.
(On/Off)
×: Applicable
–: Not applicable
cardiagn.com
When “Up”, “Keep” or “Down” is selected on display screen, the following items are displayed when system is
normal.
Display
Test item Display Item
Up Keep Down
FR RH IN SOL Off On* On*
FR RH SOL
FR RH OUT SOL Off Off On*
FRLH IN SOL Off On* On*
FR LH SOL
FR LH OUT SOL Off Off On*
RR RH IN SOL Off On* On*
RR RH SOL
RR RH OUT SOL Off Off On*
RR LH IN SOL Off On* On*
RR LH SOL
RR LH OUT SOL Off Off On*
*: Immediately after being selected, status is “On”. Status changes to “Off” after approx. 2 seconds.
ABS IN Valve (ACT) and ABS OUT Valve (ACT)
When “Up”, “ACT KEEP” or “ACT UP” is selected on display screen, the following items are displayed when
system is normal.
Display
Test item Display Item
Up ACT KEEP ACT UP
FR RH IN SOL Off Off On*
FR RH OUT SOL Off Off Off
FR RH SOL (ACT)
CV1 Off On* On*
SV1 Off Off On*
FR LH IN SOL Off Off On*
FR LH OUT SOL Off Off Off
FR LH SOL (ACT)
CV1 Off On* On*
SV1 Off Off On*
BRC
Display
Test item Display Item
On Off
cardiagn.com
STOP LAMP ON RELAY STOP LAMP ON RELAY On Off G
NOTE:
Display occasionally changes On/Off for a moment after ignition switch is turned ON. This is operation for
checking purposes and is not a malfunction. H
FUNCTION TEST
Self diagnostic results of the ABS system are displayed with an “OK” or “NG”.
I
WORK SUPPORT
Conditions Description
J
Steering angle sensor neutral position adjustment can be per-
ST ANGLE SENSOR ADJUSTMENT
formed. Refer to BRC-70, "Description".
Decel G sensor calibration can be performed. Refer to BRC-72,
DECEL G SEN CALIBRATION
"Description".
K
Data monitor
Monitor item Display content Reference value in
Condition
normal operation
0 [km/h (MPH)] Vehicle stopped
FR LH SENSOR Wheel speed Nearly matches the speed meter display Vehicle running
(± 10% or less) (Note 1)
0 [km/h (MPH)] Vehicle stopped
FR RH SENSOR Wheel speed Nearly matches the speed meter display Vehicle running
(± 10% or less) (Note 1)
0 [km/h (MPH)] Vehicle stopped
RR LH SENSOR Wheel speed
cardiagn.com
Nearly matches the speed meter display Vehicle running
(± 10% or less) (Note 1)
0 [km/h (MPH)] Vehicle stopped
RR RH SENSOR Wheel speed Nearly matches the speed meter display Vehicle running
(± 10% or less) (Note 1)
Vehicle stopped Approx. 0 G
Longitudinal acceleration detected by Decel
DECEL G-SEN During acceleration Positive value
G-Sensor
During deceleration Negative value
Active ON
FR RH IN SOL Operation status of each solenoid valve
Inactive OFF
Active ON
FR RH OUT SOL Operation status of each solenoid valve
Inactive OFF
Active ON
FR LH IN SOL Operation status of each solenoid valve
Inactive OFF
Active ON
FR LH OUT SOL Operation status of each solenoid valve
Inactive OFF
Active ON
RR RH IN SOL Operation status of each solenoid valve
Inactive OFF
Active ON
RR RH OUT SOL Operation status of each solenoid valve
Inactive OFF
Active ON
RR LH IN SOL Operation status of each solenoid valve
Inactive OFF
Active ON
RR LH OUT SOL Operation status of each solenoid valve
Inactive OFF
cardiagn.com
When SLIP indicator lamp is ON or blink-
SLIP indicator lamp ON
SLIP/VDC LAMP ing G
(Note 2)
When SLIP indicator lamp is OFF OFF
Battery voltage supplied to the ABS actuator
BATTERY VOLT Ignition switch ON 10 – 16 V H
and electric unit (control unit)
1st gear 1
2nd gear 2
3rd gear 3 I
GEAR Gear position determined by TCM
4th gear 4
5th gear 5
6th gear 6
J
With engine stopped 0 rpm
Yaw rate detected by yaw rate/side/decel G When vehicle is stopped Approx. 0 d/s
YAW RATE SEN
sensor When vehicle is turning −75 to 75 d/s
L
Transmission range switch signal ON/OFF A/T shift position = R position ON
R POSI SIG
condition A/T shift position = other than R position OFF
cardiagn.com
When steering wheel is turned to the right
Approx. +90°
by 90°
With ignition switch turned ON and brake
0 bar
pedal released
Brake fluid pressure detected by pressure 0 to 255 bar
PRESS SENSOR
sensor With ignition switch turned ON and brake (Pressure increased
pedal depressed according to pedal
effort.)
With ignition switch turned ON and brake
Approx. 0 bar
ACCUM PRESS pedal released
Accumulator pressure
SEN With ignition switch turned ON and brake
0 to 210 bar
pedal depressed
EBD is active ON
EBD SIGNAL EBD operation
EBD is inactive OFF
ABS is active ON
ABS SIGNAL ABS operation
ABS is inactive OFF
TCS is active ON
TCS SIGNAL TCS operation
TCS is inactive OFF
VDC is active ON
VDC SIGNAL VDC operation
VDC is inactive OFF
In EBD fail-safe ON
EBD FAIL SIG EBD fail-safe signal
EBD is normal OFF
In ABS fail-safe ON
ABS FAIL SIG ABS fail-safe signal
ABS is normal OFF
In TCS fail-safe ON
TCS FAIL SIG TCS fail-safe signal
TCS is normal OFF
In VDC fail-safe ON
VDC FAIL SIG VDC fail-safe signal
VDC is normal OFF
Crank is active ON
CRANKING SIG Crank operation
Crank is inactive OFF
When brake fluid level switch is ON ON
FLUID LEV SW Brake fluid level switch signal status
When brake fluid level switch is OFF OFF
cardiagn.com
When hill start assist not active OFF
G
NOTE:
• 1: Confirm tire pressure is normal.
• 2: ON and OFF timing for warning lamp and indicator lamp. H
- ABS warning lamp: Refer to BRC-147, "Component Function Check".
- Brake warning lamp: Refer to BRC-148, "Component Function Check".
- SLIP indicator lamp: Refer to BRC-150, "Component Function Check".
I
- VDC OFF indicator lamp: Refer to BRC-149, "Component Function Check".
• 3: The CONSULT will display DDS (Downhill Drive Support) when referring to the Hill Descent Control system.
• 4: The CONSULT will display USS (Uphill Start Support) when referring to the HIll Start Assist system.
J
Fail-safe INFOID:0000000013191038
cardiagn.com
normal.
• When power supply voltage of front wheel sensor LH is low.
• When distance between front wheel sensor LH and front wheel sensor LH rotor is
C1108 large.
• When installation of front wheel sensor LH or front wheel sensor LH rotor is not
normal.
• When ignition voltage is 10 V or less. The following functions are sus-
C1109
• When ignition voltage is 16 V or more. pended:
• VDC function
• TCS function
• When a malfunction is detected in motor or motor relay. • ABS function
C1111 • When a low pressure malfunction is detected in accumulator. • EBD function
• When a malfunction is detected in accumulator pressure sensor. • hill start assist function
• hill descent control function
• BLSD function
When difference in wheel speed between any wheel and others is detected while the The following functions are sus-
C1115
vehicle is driven, because of installation of tires other than specified. pended:
• VDC function
C1116 • When stop lamp switch signal is not input when brake pedal is depressed.
• TCS function
• ABS function
• hill start assist function
C1118 When a malfunction is detected in transfer control unit.
• hill descent control function
• BLSD function
C1120 When a malfunction is detected in front LH ABS IN valve.
C1121 When a malfunction is detected in front LH ABS OUT valve. The following functions are sus-
pended:
C1122 When a malfunction is detected in front RH ABS IN valve. • VDC function
C1123 When a malfunction is detected in front RH ABS OUT valve. • TCS function
• ABS function
C1124 When a malfunction is detected in rear LH ABS IN valve. • EBD function
C1125 When a malfunction is detected in rear LH ABS OUT valve. • hill start assist function
• hill descent control function
C1126 When a malfunction is detected in rear RH ABS IN valve. • BLSD function
C1127 When a malfunction is detected in rear RH ABS OUT valve.
The following functions are sus-
pended:
• VDC function
C1130 When a malfunction is detected in ECM system. • TCS function
• hill start assist function
• hill descent control function
• BLSD function
cardiagn.com
• When an open circuit is detected in brake fluid level switch circuit. • hill start assist function
• hill descent control function G
C1160 When calibration of yaw rate/side/decel G sensor is not complete. • BLSD function
C1164 When a malfunction is detected in cut valve 1. The following functions are sus-
C1165 When a malfunction is detected in cut valve 2.
pended: H
• VDC function
C1166 When a malfunction is detected in suction valve 1. • TCS function
• ABS function
• EBD function I
C1167 When a malfunction is detected in suction valve 2. • hill start assist function
• hill descent control function
• BLSD function
J
C1170 When the information in ABS actuator and electric unit (control unit) is not the same. The following functions are sus-
pended:
• VDC function
• TCS function K
C1187 When a malfunction is detected in differential lock control unit system. • ABS function
• hill start assist function
• hill descent control function
• BLSD function L
The following functions are sus-
pended:
• VDC function M
When performing excessive brake pedal operation with the vehicle stopped. [When • TCS function
C118E accumulator fluid pressure reaches 11.43 MPa (114 bar, 116.6 kg/cm2, 1657 psi) af- • ABS function
ter reaching 17.3 MPa (173 bar, 176.5 kg/cm2, 2509 psi.] • EBD function
• hill start assist function N
• hill descent control function
• BLSD function
The following functions are sus- O
pended:
• VDC function
When CAN communication signal is not continuously received for 2 seconds or • TCS function
U1000
more. • ABS function P
• hill start assist function
• hill descent control function
• BLSD function
PROTECTION FUNCTION
The SLIP indicator lamp, ABS warning lamp and brake warning lamp turn ON and DTC “C118E” may be
detected in self-diagnosis result of “ABS” when the brake pedal is excessively operated, such as air bleeding.
This is not a system malfunction because this occurs due to the temporary decrease in accumulator fluid pres-
Revision: March 2016 BRC-53 2016 Titan NAM
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
< ECU DIAGNOSIS INFORMATION > [VDC/TCS/ABS]
sure. The system returns to normal condition when the accumulator fluid pressure reaches the specified pres-
sure with the ignition switch ON and the SLIP indicator lamp, ABS warning lamp, and brake warning lamp
turned OFF. After these steps, erase self-diagnosis results for “ABS” with CONSULT.
cardiagn.com
When multiple DTCs are displayed simultaneously, check one by one depending on the following priority list.
cardiagn.com
C1120 FR LH IN ABS SOL BRC-106, "Diagnosis Procedure" G
C1121 FR LH OUT ABS SOL BRC-108, "Diagnosis Procedure"
C1122 FR RH IN ABS SOL BRC-106, "Diagnosis Procedure"
H
C1123 FR RH OUT ABS SOL BRC-108, "Diagnosis Procedure"
C1124 RR LH IN ABS SOL BRC-106, "Diagnosis Procedure"
C1125 RR LH OUT ABS SOL BRC-108, "Diagnosis Procedure" I
C1126 RR RH IN ABS SOL BRC-106, "Diagnosis Procedure"
C1127 RR RH OUT ABS SOL BRC-108, "Diagnosis Procedure"
J
C1130 ENGINE SIGNAL 1 BRC-109, "Diagnosis Procedure"
C1140 ACTUATOR RLY BRC-111, "Diagnosis Procedure"
C1142 PRESS SEN CIRCUIT BRC-113, "Diagnosis Procedure" K
C1143 ST ANG SEN CIRCUIT BRC-116, "Diagnosis Procedure"
C1144 ST ANG SEN SIGNAL BRC-120, "Diagnosis Procedure"
L
C1145 YAW RATE SENSOR
BRC-123, "Diagnosis Procedure"
C1146 SIDE G-SEN CIRCUIT
C1155 BR FLUID LEVEL LOW BRC-126, "Diagnosis Procedure" M
C1160 DECEL G SEN SET BRC-130, "Diagnosis Procedure"
C1164 CV 1
BRC-132, "Diagnosis Procedure" N
C1165 CV 2
C1166 SV 1
BRC-134, "Diagnosis Procedure"
C1167 SV 2
O
C1170 VARIANT CODING BRC-136, "Diagnosis Procedure"
C1187 DIFLOCK CONT BRC-137, "Diagnosis Procedure"
C118E ACCUMULATOR PRESS BRC-138, "Diagnosis Procedure" P
U1000 CAN COMM CIRCUIT BRC-139, "Diagnosis Procedure"
WIRING DIAGRAM
BRAKE CONTROL SYSTEM
Wiring Diagram INFOID:0000000013123931
cardiagn.com
AAFWA0229GB
BRC
cardiagn.com
G
AAFWA0230GB
cardiagn.com
AAFWA0231GB
BRC
cardiagn.com
G
AAFIA0570GB
cardiagn.com
AAFIA0571GB
BRC
cardiagn.com
G
AAFIA0572GB
cardiagn.com
AAFIA0573GB
BRC
cardiagn.com
G
AAFIA0574GB
cardiagn.com
AAFIA0575GB
BRC
cardiagn.com
G
AAFIA0576GB
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow INFOID:0000000013123932
DETAILED FLOW
1.INTERVIEW THE CUSTOMER
Clarify customer concerns before inspection. First of all, perform an interview utilizing BRC-67, "Diagnostic
Work Sheet" and reproduce the symptom as well as fully understand it. Ask customer about his/her concerns
carefully. Check symptoms by driving vehicle with customer, if necessary.
CAUTION:
Customers are not professional. Never guess easily like “maybe the customer means that...,” or “
maybe the customer mentions this symptom”.
>> GO TO 2.
2.CHECK SYMPTOM
Reproduce the symptom that is indicated by the customer, based on the information from the customer
cardiagn.com
obtained in the interview. Also check that the symptom is not caused by fail-safe mode. Refer to BRC-51,
"Fail-safe".
CAUTION:
When the symptom is caused by normal operation, fully inspect each portion and obtain the under-
standing of customer that the symptom is not caused by a malfunction.
>> GO TO 3.
3.PERFORM THE SELF-DIAGNOSIS
CONSULT
1. Turn the ignition switch OFF → ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” mode of “ABS”.
Is DTC detected?
YES >> Record or print Self Diagnostic Results and Freeze Frame Data (FFD). GO TO 4.
NO >> GO TO 6.
4.RECHECK THE SYMPTOM
CONSULT
1. Erase “Self Diagnostic Result” mode of “ABS”.
2. Turn the ignition switch OFF → ON → OFF.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
3. Perform DTC confirmation procedures for the malfunctioning system.
NOTE:
If some DTCs are detected at the some time, determine the order for performing the diagnosis based on
BRC-54, "DTC Inspection Priority Chart".
Is DTC detected?
YES >> GO TO 5.
NO >> Check harness and connectors based on the information obtained in the interview. Refer to GI-43,
"Intermittent Incident".
5.REPAIR OR REPLACE MALFUNCTIONING COMPONENT
1. Repair or replace malfunctioning components.
2. Reconnect component or connector after repairing or replacing.
3. When DTC is detected, erase “Self Diagnostic Result” mode of “ABS”.
CAUTION:
>> GO TO 7.
6.IDENTIFY MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS B
cardiagn.com
G
Diagnostic Work Sheet INFOID:0000000013123933
DESCRIPTION
H
• In general, customers have their own criteria for a problem. Therefore, it is important to understand the
symptom and status well enough by asking the customer about his/her concerns carefully. To systemize all
the information for the diagnosis, prepare the interview sheet referring to the interview points.
• In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected. I
INTERVIEW SHEET SAMPLE
Interview sheet
J
Other conditions
Memo
cardiagn.com
1.PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR D
Perform the neutral position adjustment for the steering angle sensor.
E
>> Refer to BRC-70, "Work Procedure", GO TO 2.
2.PERFORM CALIBRATION OF THE DECEL G SENSOR
Perform calibration of the decel G sensor. BRC
cardiagn.com
>> Refer to BRC-72, "Work Procedure".
G
Refer to the table below to determine if adjustment of steering angle sensor neutral position is required.
×: Required –: Not required
cardiagn.com
Adjusting wheel alignment ×
Battery disconnection —
>> GO TO 2.
2.PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR
1. On the CONSULT screen, touch “Work support” and “ST ANGLE SENSOR ADJUSTMENT” in order.
2. Touch “Start”.
CAUTION:
Do not touch steering wheel while adjusting steering angle sensor.
3. After approximately 10 seconds, touch “End”.
NOTE:
After approximately 60 seconds, it ends automatically.
4. Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3.
3.CHECK DATA MONITOR
1. Run vehicle with front wheels in straight-ahead position, then stop.
2. Select “Data Monitor” mode. Then make sure “STR ANGLE SIG” is within 0±2.5°.
Is the steering angle within the specified range?
YES >> GO TO 4.
NO >> Perform the neutral position adjustment for the steering angle sensor again, GO TO 1
4.ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
Revision: March 2016 BRC-70 2016 Titan NAM
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
< BASIC INSPECTION > [VDC/TCS/ABS]
• ABS actuator and electric unit (control unit): Refer to BRC-43, "CONSULT Function (ABS)".
• ECM: Refer to EC-103, "CONSULT Function" (Cummins 5.0L) or EC-1325, "CONSULT Function" A
(VK56VD).
Are the memories erased?
YES >> Inspection End B
NO >> Check the items indicated by the self-diagnosis.
BRC
cardiagn.com
G
Refer to the table below to determine if calibration of the decel G sensor is required.
×: Required –: Not required
cardiagn.com
Adjusting wheel alignment —
Removing/Installing yaw rate/side/decel G sensor ×
Replacing yaw rate/side/decel G sensor ×
>> GO TO 2.
2.PERFORM CALIBRATION OF DECEL G SENSOR
1. On the CONSULT screen, touch “Work support” and “DECEL G SEN CALIBRATION” in order.
2. Touch “Start”.
3. After approximately 10 seconds, touch “End”.
NOTE:
After approximately 60 seconds, it ends automatically.
4. Turn ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3.
3.CHECK DATA MONITOR
1. Run vehicle with front wheels in straight-ahead position, then stop.
2. Select “Data Monitor”. Then make sure “DECEL G SEN” is within ± 0.05G.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Perform calibration of decel G sensor again, GO TO 1.
4.ERASE THE SELF-DIAGNOSIS MEMORY
Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.
BRC
cardiagn.com
G
DTC/CIRCUIT DIAGNOSIS
C1101, C1102, C1103, C1104 WHEEL SENSOR
DTC Description INFOID:0000000013147635
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content)
RR RH SENSOR-1
C1101 When an open circuit is detected in rear RH wheel sensor circuit.
(Rear RH wheel sensor-1)
RR LH SENSOR-1
C1102 When an open circuit is detected in rear LH wheel sensor circuit.
(Rear LH wheel sensor-1)
FR RH SENSOR-1
C1103 When an open circuit is detected in front RH wheel sensor circuit.
(Front RH wheel sensor-1)
FR LH SENSOR-1
C1104 When an open circuit is detected in front LH wheel sensor circuit.
(Front LH wheel sensor-1)
POSSIBLE CAUSE
cardiagn.com
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
>> GO TO 2.
2.CHECK DTC DETECTION
CONSULT
1. Start the engine.
2. Drive the vehicle at approx. 50 km/h (31 MPH) or more for approx. 2 minutes.
3. Stop the vehicle.
4. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
5. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
6. Repeat step 4 to 5 two or more times.
7. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1101”, “C1102”, “C1103” or “C1104” detected?
YES-1 >> “C1101”, “C1102”, “C1103” or “C1104” is displayed by “CRNT”: Proceed to BRC-75, "Diagnosis
Procedure".
CAUTION:
Never check between wheel sensor harness connector terminals. C
1.CHECK WHEEL SENSOR
1. Turn the ignition switch OFF.
2. Check the wheel sensor for damage. D
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2. E
2.REPLACE WHEEL SENSOR (1)
CONSULT BRC
1. Replace the wheel sensor.
- Front: Refer to BRC-159, "FRONT WHEEL SENSOR : Removal and Installation".
cardiagn.com
- Rear: Refer to BRC-160, "REAR WHEEL SENSOR : Removal and Installation".
G
2. Erase “Self Diagnostic Result” mode of “ABS”.
3. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON. H
4. Start the engine.
5. Drive the vehicle at approx. 50 km/h (31 MPH) or more for approx. 2 minutes.
NOTE: I
Vehicle must be driven after repair or replacement to erase the previous DTCs.
6. Stop the vehicle.
7. Turn the ignition switch OFF.
NOTE: J
Wait at least 10 seconds after turning ignition switch OFF.
8. Start the engine.
NOTE: K
Wait at least 10 seconds after start the engine.
9. Repeat step 7 to 8 two or more times.
10. Select “Self Diagnostic Result” mode of “ABS”.
L
Is DTC “C1101”, “C1102”, “C1103” or “C1104” detected?
YES >> GO TO 3.
NO >> Inspection End.
M
3.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness. N
3. Check the wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES >> GO TO 5. O
NO >> Repair / replace harness or connector, securely lock the connector, and GO TO 4.
4.PERFORM SELF DIAGNOSTIC RESULT (1)
P
CONSULT
1. Erase “Self Diagnostic Result” mode of “ABS”.
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
4. Drive the vehicle at approx. 50 km/h (31 MPH) or more for approx. 2 minutes.
NOTE:
cardiagn.com
NO >> Repair / replace harness, connector, fuse, or fusible link.
6.CHECK TERMINAL
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector and then check the ABS actu-
ator and electric unit (control unit) pin terminals for damage or loose connection with harness connector.
3. Disconnect wheel sensor harness connector and check each wheel sensor pin terminals for damage or
loose connection with harness connector.
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair / replace harness, connector, or terminal, and GO TO 7.
7.PERFORM SELF DIAGNOSTIC RESULT (2)
CONSULT
1. Connect ABS actuator and electric unit (control unit) harness connector.
2. Connect wheel sensor harness connector.
3. Erase “Self Diagnostic Result” mode of “ABS”.
4. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
5. Start the engine.
6. Drive the vehicle at approx. 50 km/h (31 MPH) or more for approx. 2 minutes.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
7. Stop the vehicle.
8. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
9. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
10. Repeat step 8 to 9 two or more times.
11. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1101”, “C1102”, “C1103” or “C1104” detected?
YES >> GO TO 8.
NO >> Inspection End.
8.CHECK WHEEL SENSOR HARNESS
1. Turn the ignition switch OFF.
ABS actuator and electric unit (control unit) Wheel sensor BRC
Continuity
Connector Terminal Connector Terminal
cardiagn.com
34 E18 (Front LH wheel)
G
19 E117 (Front RH wheel)
E125 2 Yes
36 C11 (Rear LH wheel)
21 C10 (Rear RH wheel) H
Is the inspection result normal?
YES >> GO TO 10.
NO >> Repair / replace harness or connector, and GO TO 9. I
9.PERFORM SELF DIAGNOSTIC RESULT (3)
CONSULT J
1. Connect ABS actuator and electric unit (control unit) harness connector.
2. Connect wheel sensor harness connector.
3. Erase “Self Diagnostic Result” mode of “ABS”.
4. Turn the ignition switch OFF → ON → OFF. K
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
5. Start the engine. L
6. Drive the vehicle at approx. 50 km/h (31 MPH) or more for approx. 2 minutes.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
M
7. Stop the vehicle.
8. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF. N
9. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine. O
10. Repeat step 8 to 9 two or more times.
11. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1101”, “C1102”, “C1103” or “C1104” detected?
P
YES >> GO TO 10.
NO >> Inspection End.
10.CHECK WHEEL SENSOR OUTPUT SIGNAL
1. Disconnect ABS actuator and electric unit (control unit) harness connector.
2. Disconnect wheel sensor harness connector.
3. Connect ABS active wheel sensor tester KV991J0080 (J-45741-A) to wheel sensor using appropriate
adapter.
Revision: March 2016 BRC-77 2016 Titan NAM
C1101, C1102, C1103, C1104 WHEEL SENSOR
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
4. Turn the ABS active wheel sensor tester power switch ON.
NOTE:
The green POWER indicator should illuminate. If the POWER indicator does not illuminate, replace the
battery in the ABS active wheel sensor tester before proceeding.
5. Spin the wheel of the vehicle by hand and observe the red SENSOR indicator on the ABS active wheel
sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
NOTE:
If the red SENSOR indicator illuminates but does not flash, reverse the polarity of the tester leads and
retest.
Does the ABS active wheel sensor tester detect a signal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
NO >> GO TO 11.
11.REPLACE WHEEL SENSOR
CONSULT
1. Replace the wheel sensor.
- Front: Refer to BRC-159, "FRONT WHEEL SENSOR : Removal and Installation".
- Rear: Refer to BRC-160, "REAR WHEEL SENSOR : Removal and Installation".
2. Erase “Self Diagnostic Result” mode of “ABS”.
3. Turn the ignition switch OFF → ON → OFF.
cardiagn.com
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
4. Start the engine.
5. Drive the vehicle at approx. 50 km/h (31 MPH) or more for approx. 2 minutes.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
6. Stop the vehicle.
7. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
8. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
9. Repeat step 7 to 8 two or more times.
10. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1101”, “C1102”, “C1103” or “C1104” detected?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
NO >> Inspection End.
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content) C
• When power supply voltage of rear RH wheel sensor is low.
RR RH SENSOR-2
C1105 • When distance between rear RH wheel sensor and rear RH wheel sensor rotor is large.
(Rear RH wheel sensor-2)
• When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not normal.
D
• When power supply voltage of rear LH wheel sensor is low.
RR LH SENSOR-2
C1106 • When distance between rear LH wheel sensor and rear LH wheel sensor rotor is large.
(Rear LH wheel sensor-2)
• When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not normal.
E
• When power supply voltage of front RH wheel sensor is low.
FR RH SENSOR-2
C1107 • When distance between front RH wheel sensor and front RH wheel sensor rotor is large.
(Front RH wheel sensor-2)
• When installation of front RH wheel sensor or front RH wheel sensor rotor is not normal.
• When power supply voltage of front LH wheel sensor is low. BRC
FR LH SENSOR-2
C1108 • When distance between front LH wheel sensor and front LH wheel sensor rotor is large.
(Front LH wheel sensor-2)
• When installation of front LH wheel sensor or front LH wheel sensor rotor is not normal.
cardiagn.com
POSSIBLE CAUSE G
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC. H
>> GO TO 2. N
2.CHECK DTC DETECTION
CONSULT O
1. Start the engine.
2. Drive the vehicle at approx. 50 km/h (31 MPH) or more for approx. 2 minutes.
3. Stop the vehicle.
4. Turn the ignition switch OFF. P
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
5. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
6. Repeat step 4 to 5 two or more times.
7. Select “Self Diagnostic Result” mode of “ABS”.
CAUTION:
Never check between wheel sensor harness connector terminals.
1.CHECK WHEEL HUB ASSEMBLY
Check that there is no excessive looseness in wheel hub assembly.
• Front: Refer to FSU-6, "Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the wheel hub assembly, and GO TO 2.
• Front: Refer to FSU-20, "Removal and Installation".
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
cardiagn.com
CUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to BRC-140,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair / replace harness, connector, fuse, or fusible link.
3.CHECK TIRE
1. Turn the ignition switch OFF.
2. Check the tire air pressure, wear and size. Refer to WT-65, "Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Adjust air pressure or replace tire, and GO TO 4.
4.CHECK DATA MONITOR (1)
CONSULT
1. Erase “Self Diagnostic Result” mode of “ABS”.
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
4. Select “ABS” and “Data Monitor”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and
“RR RH SENSOR”.
NOTE:
Set the “Data Monitor” recording speed to “10 msec”.
5. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
Note the difference at 50 km/h (31 MPH) between the wheel speed detected by the error detecting wheel sen-
sor and the maximum/minimum wheel speed detected by the normal wheel sensors. Is the difference within
5%, respectively?
YES >> GO TO 5.
NO >> GO TO 6.
5.PERFORM SELF DIAGNOSTIC RESULT (1)
CONSULT
1. Stop the vehicle.
cardiagn.com
• Rear: Refer to BRC-160, "REAR WHEEL SENSOR : Removal and Installation". G
Is the inspection result normal?
YES >> GO TO 7.
NO >> GO TO 8. H
7. CHECK WHEEL SENSOR OUTPUT SIGNAL
1. Disconnect ABS actuator and electric unit (control unit) harness connector.
2. Disconnect wheel sensor harness connector. I
3. Connect ABS active wheel sensor tester KV991J0080 (J-45741-A) to wheel sensor using appropriate
adapter.
4. Turn the ABS active wheel sensor tester power switch ON. J
NOTE:
The green POWER indicator should illuminate. If the POWER indicator does not illuminate, replace the
battery in the ABS active wheel sensor tester before proceeding.
5. Spin the wheel of the vehicle by hand and observe the red SENSOR indicator on the ABS active wheel K
sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.
NOTE:
If the red SENSOR indicator illuminates but does not flash, reverse the polarity of the tester leads and L
retest.
Does the ABS active wheel sensor tester detect a signal?
YES >> GO TO 11. M
NO >> GO TO 8.
8.REPLACE WHEEL SENSOR (1)
N
CONSULT
1. Replace the wheel sensor.
- Front: Refer to BRC-159, "FRONT WHEEL SENSOR : Removal and Installation".
- Rear: Refer to BRC-160, "REAR WHEEL SENSOR : Removal and Installation". O
2. Erase “Self Diagnostic Result” mode of “ABS”.
3. Turn the ignition switch OFF → ON → OFF.
NOTE: P
Wait at least 10 seconds after turning ignition switch OFF or ON.
4. Start the engine.
5. Select “ABS” and “Data Monitor”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and
“RR RH SENSOR”.
NOTE:
Set the “Data Monitor” recording speed to “10 msec”.
6. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.
NOTE:
Revision: March 2016 BRC-81 2016 Titan NAM
C1105, C1106, C1107, C1108 WHEEL SENSOR
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
Vehicle must be driven after repair or replacement to erase the previous DTCs.
Note the difference at 50 km/h (31 MPH) between the wheel speed detected by the error detecting wheel sen-
sor and the maximum/minimum wheel speed detected by the normal wheel sensors. Is the difference within
5%, respectively?
YES >> GO TO 8.
NO >> GO TO 20.
9.PERFORM SELF DIAGNOSTIC RESULT (2)
CONSULT
1. Stop the vehicle.
2. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
3. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
4. Repeat step 2 to 3 two or more times.
5. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected?
YES >> GO TO 20.
cardiagn.com
NO >> Inspection End.
10.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
3. Check the wheel sensor harness connector for disconnection or looseness.
Is the inspection result normal?
YES >> GO TO 12.
NO >> Repair / replace harness or connector, securely lock the connector, and GO TO 10.
11.CHECK DATA MONITOR (2)
CONSULT
1. Erase “Self Diagnostic Result” mode of “ABS”.
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
4. Select “ABS” and “Data Monitor”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and
“RR RH SENSOR”.
NOTE:
Set the “Data Monitor” recording speed to “10 msec”.
5. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
Note the difference at 50 km/h (31 MPH) between the wheel speed detected by the error detecting wheel sen-
sor and the maximum/minimum wheel speed detected by the normal wheel sensors. Is the difference within
5%, respectively?
YES >> GO TO 11.
NO >> GO TO 12.
12.PERFORM SELF DIAGNOSTIC RESULT (3)
CONSULT
1. Stop the vehicle.
2. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
3. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
cardiagn.com
3. Erase “Self Diagnostic Result” mode of “ABS”.
4. Turn the ignition switch OFF → ON → OFF. G
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
5. Start the engine. H
6. Select “ABS” and “Data Monitor”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and
“RR RH SENSOR”.
NOTE:
Set the “Data Monitor” recording speed to “10 msec”. I
7. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs. J
Note the difference at 50 km/h (31 MPH) between the wheel speed detected by the error detecting wheel sen-
sor and the maximum/minimum wheel speed detected by the normal wheel sensors. Is the difference within
5%, respectively? K
YES >> GO TO 14.
NO >> GO TO 15.
15. PERFORM SELF DIAGNOSTIC RESULT (4) L
CONSULT
1. Stop the vehicle.
2. Turn the ignition switch OFF. M
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
3. Start the engine. N
NOTE:
Wait at least 10 seconds after start the engine.
4. Repeat step 2 to 3 two or more times.
5. Select “Self Diagnostic Result” mode of “ABS”. O
Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected?
YES >> GO TO 15.
NO >> Inspection End. P
cardiagn.com
5. Start the engine.
6. Select “ABS” and “Data Monitor”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and
“RR RH SENSOR”.
NOTE:
Set the “Data Monitor” recording speed to “10 msec”.
7. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
Note the difference at 50 km/h (31 MPH) between the wheel speed detected by the error detecting wheel sen-
sor and the maximum/minimum wheel speed detected by the normal wheel sensors. Is the difference within
5%, respectively?
YES >> GO TO 17.
NO >> GO TO 18.
18.PERFORM SELF DIAGNOSTIC RESULT (5)
CONSULT
1. Stop the vehicle.
2. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
3. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
4. Repeat step 2 to 3 two or more times.
5. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected?
YES >> GO TO 18.
NO >> Inspection End.
19.REPLACE WHEEL SENSOR (2)
CONSULT
1. Replace the wheel sensor.
- Front: Refer to BRC-159, "FRONT WHEEL SENSOR : Removal and Installation".
- Rear: Refer to BRC-160, "REAR WHEEL SENSOR : Removal and Installation".
2. Erase “Self Diagnostic Result” mode of “ABS”.
3. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
cardiagn.com
NOTE: G
Wait at least 10 seconds after start the engine.
4. Repeat step 2 to 3 two or more times.
5. Select “Self Diagnostic Result” mode of “ABS”.
H
Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected?
YES >> GO TO 20.
NO >> Inspection End.
I
21.REPLACE SENSOR ROTOR
CONSULT
1. Replace the sensor rotor. J
- Front: Refer to BRC-159, "FRONT WHEEL SENSOR : Removal and Installation".
- Rear: Refer to BRC-160, "REAR WHEEL SENSOR : Removal and Installation".
2. Erase “Self Diagnostic Result” mode of “ABS”. K
3. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
4. Start the engine. L
5. Drive the vehicle at approx. 50 km/h (31 MPH) or more for approx. 2 minutes.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs. M
6. Stop the vehicle.
7. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF. N
8. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine. O
9. Repeat step 7 to 8 two or more times.
10. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1105”, “C1106”, “C1107” or “C1108” detected? P
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
NO >> Inspection End.
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content)
When ignition power supply voltage is in following state.
BATTERY VOLTAGE [ABNORMAL]
C1109 • Ignition power supply voltage: 10 V ≥ ignition power supply voltage.
(Battery voltage [abnormal])
• Ignition power supply voltage: 16 V ≤ ignition power supply voltage.
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
cardiagn.com
• ABS actuator and electric unit (control unit) power supply sys- • IPDM E/R
tem • ABS actuator and electric unit (control unit) power supply sys-
• Fuse tem
• Fusible link • Fuse
• Battery • Fusible link
• Charge system • Battery
• Charge system
>> GO TO 2.
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1109” detected?
YES-1 >> “CRNT” is displayed: Proceed to BRC-86, "Diagnosis Procedure".
YES-2 >> “PAST” is displayed: Inspection End. (Erase the memory of “Self Diagnostic Result” mode of
“ABS”.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure INFOID:0000000013147640
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
cardiagn.com
YES >> GO TO 4. G
NO >> Repair / replace harness, connector, fuse, or fusible link.
4.CHECK TERMINAL H
1. Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with
harness connector.
2. Check the IPDM E/R pin terminals for damage or loose connection with harness connector.
I
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
J
NO >> Repair / replace harness, connector, or terminal.
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content)
PUMP MOTOR
C1111 When a malfunction is detected in motor or motor relay.
(Pump motor and motor relay)
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
cardiagn.com
tem tem
• Fuse • Fuse
• Fusible link • Fusible link
• Battery • Battery
• Motor/accumulator assembly
>> GO TO 2.
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF → ON, and wait 30 seconds.
2. Drive the vehicle at approx. 50 km/h (31 MPH) or more for approx. 2 minutes.
3. Stop the vehicle.
4. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
5. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
6. Repeat step 4 to 5 two or more times.
7. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1111” detected?
YES-1 >> “CRNT” is displayed: Proceed to BRC-88, "Diagnosis Procedure".
YES-2 >> “PAST” is displayed: Inspection End. (Erase the memory of “Self Diagnostic Result” mode of
“ABS”.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure INFOID:0000000013147952
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
cardiagn.com
NO >> Inspection End. G
3.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
H
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to BRC-140,
"Diagnosis Procedure".
Is the inspection result normal?
I
YES >> GO TO 5.
NO >> Repair / replace harness, connector, or fuse, and GO TO 4.
4.ERASE SELF DIAGNOSTIC RESULT (1) J
CONSULT
1. Drive the vehicle at approx. 50 km/h (31 MPH) or more for approx. 2 minutes.
NOTE: K
Vehicle must be driven after repair or replacement to erase the previous DTCs.
2. Stop the vehicle.
3. Erase “Self Diagnostic Result” mode of “ABS”. L
4. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
M
>> Inspection End.
5.CHECK TERMINAL N
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with
harness connector. O
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation". P
NO >> Repair / replace harness or connector, and GO TO 6.
6.ERASE SELF-DIAGNOSIS RESULT (2)
CONSULT
1. Drive the vehicle at approx. 50 km/h (31 MPH) or more for approx. 2 minutes.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
cardiagn.com
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content) C
ABS SENSOR [ABNORMAL
SIGNAL] When difference in wheel speed between any wheel and others is detected the vehicle is
C1115
(Wheel sensor [abnormal sig- driven, because of installation of other tires than specified.
nal]) D
POSSIBLE CAUSE
NOTE: E
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
BRC
PAST DTC CRNT DTC
• Harness or connector
cardiagn.com
• Harness or connector • Wheel sensor
• Wheel sensor • Sensor rotor G
• Sensor rotor • ABS actuator and electric unit (control unit)
• ABS actuator and electric unit (control unit) power supply sys- • ABS actuator and electric unit (control unit) power supply sys-
tem tem
• Fuse • Fuse
H
• Fusible link • Fusible link
• Battery • Battery
• Tire size I
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING J
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
K
>> GO TO 2.
2.CHECK DTC DETECTION
L
CONSULT
1. Start the engine.
2. Drive the vehicle at approx. 50 km/h (19 MPH) or more for approx. 2 minutes.
3. Stop the vehicle. M
4. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF. N
5. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
6. Repeat step 4 to 5 two or more times. O
7. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1115” detected?
YES-1 >> “CRNT” is displayed: Proceed to BRC-91, "Diagnosis Procedure". P
YES-2 >> “PAST” is displayed: Inspection End. (Erase the memory of self-diagnosis results.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure INFOID:0000000013147956
CAUTION:
cardiagn.com
Vehicle must be driven after repair or replacement to erase the previous DTCs.
Note the difference at 50 km/h (31 MPH) between the wheel speed detected by the error detecting wheel sen-
sor and the maximum/minimum wheel speed detected by the normal wheel sensors. Is the difference within
5%, respectively?
YES >> GO TO 3.
NO >> GO TO 4.
3.PERFORM SELF DIAGNOSTIC RESULT (1)
CONSULT
1. Stop the vehicle.
2. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
3. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
4. Repeat step 2 to 3 two or more times.
5. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1115” detected?
YES >> GO TO 4.
NO >> Inspection End.
4.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to BRC-140,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair / replace harness, connector, fuse, or fusible link.
5.CHECK WHEEL SENSOR
1. Turn the ignition switch OFF.
2. Check the wheel sensor for damage.
3. Remove dust and foreign matter adhered to the sensor rotor with a vacuum dust collector through the
wheel sensor mounting hole.
CAUTION:
Install wheel sensor with no backlash and float, and tighten the mounting bolt to the specified
torque.
cardiagn.com
NOTE: G
Vehicle must be driven after repair or replacement to erase the previous DTCs.
Note the difference at 50 km/h (31 MPH) between the wheel speed detected by the error detecting wheel sen-
sor and the maximum/minimum wheel speed detected by the normal wheel sensors. Is the difference within H
5%, respectively?
YES >> GO TO 7.
NO >> GO TO 19.
I
7. PERFORM SELF DIAGNOSTIC RESULT (2)
CONSULT
1. Stop the vehicle. J
2. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF. K
3. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
4. Repeat step 2 to 3 two or more times. L
5. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1115” detected?
YES >> GO TO 8. M
NO >> Inspection End.
8.CHECK CONNECTOR N
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
3. Check the wheel sensor harness connector for disconnection or looseness.
O
Is the inspection result normal?
YES >> GO TO 11.
NO >> Repair / replace harness or connector, securely lock the connector, and GO TO 9.
P
9.CHECK DATA MONITOR (2)
CONSULT
1. Erase “Self Diagnostic Result” mode of “ABS”.
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
cardiagn.com
Wait at least 10 seconds after start the engine.
4. Repeat step 2 to 3 two or more times.
5. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1115” detected?
YES >> GO TO 11.
NO >> Inspection End.
11.CHECK TERMINAL
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector and then check the ABS actu-
ator and electric unit (control unit) pin terminals for damage or loose connection with harness connector.
3. Disconnect wheel sensor harness connector and check each wheel sensor pin terminals for damage or
loose connection with harness connector.
Is the inspection result normal?
YES >> GO TO 14.
NO >> Repair / replace harness, connector, or terminal, and GO TO 12.
12.CHECK DATA MONITOR (3)
CONSULT
1. Connect ABS actuator and electric unit (control unit) harness connector.
2. Connect wheel sensor harness connector.
3. Erase “Self Diagnostic Result” mode of “ABS”.
4. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
5. Start the engine.
6. Select “ABS” and “Data Monitor”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and
“RR RH SENSOR”.
NOTE:
Set the “Data Monitor” recording speed to “10 msec”.
7. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
Note the difference at 50 km/h (31 MPH) between the wheel speed detected by the error detecting wheel sen-
sor and the maximum/minimum wheel speed detected by the normal wheel sensors. Is the difference within
5%, respectively?
YES >> GO TO 13.
NO >> GO TO 14.
cardiagn.com
sensor harness connector. (Check continuity while turning steering wheel left and right, or while moving G
center harness in wheel housing.)
- Measurement connector and terminal for power supply circuit
H
ABS actuator and electric unit (control unit) Wheel sensor
Continuity
Connector Terminal Connector Terminal
20 E18 (Front LH wheel) I
33 E117 (Front RH wheel)
E125 1 Yes
22 C11 (Rear LH wheel)
J
35 C10 (Rear RH wheel)
- Measurement connector and terminal for signal circuit
K
ABS actuator and electric unit (control unit) Wheel sensor
Continuity
Connector Terminal Connector Terminal
34 E18 (Front LH wheel)
L
cardiagn.com
NO >> GO TO 17.
16.PERFORM SELF DIAGNOSTIC RESULT (5)
CONSULT
1. Stop the vehicle.
2. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
3. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
4. Repeat step 2 to 3 two or more times.
5. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1115” detected?
YES >> GO TO 17.
NO >> Inspection End.
17.REPLACE WHEEL SENSOR (2)
CONSULT
1. Replace the wheel sensor.
- Front: Refer to BRC-159, "FRONT WHEEL SENSOR : Removal and Installation".
- Rear: Refer to BRC-160, "REAR WHEEL SENSOR : Removal and Installation".
2. Erase “Self Diagnostic Result” mode of “ABS”.
3. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
4. Start the engine.
5. Select “ABS” and “Data Monitor”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and
“RR RH SENSOR”.
NOTE:
Set the “Data Monitor” recording speed to “10 msec”.
6. Read a value (wheel speed) of both normal wheel sensors and error-detecting wheel sensor.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
Note the difference at 50 km/h (31 MPH) between the wheel speed detected by the error detecting wheel sen-
sor and the maximum/minimum wheel speed detected by the normal wheel sensors. Is the difference within
5%, respectively?
YES >> GO TO 18.
CONSULT
1. Stop the vehicle. B
2. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
3. Start the engine. C
NOTE:
Wait at least 10 seconds after start the engine.
4. Repeat step 2 to 3 two or more times. D
5. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1115” detected?
YES >> GO TO 19. E
NO >> Inspection End.
19.REPLACE SENSOR ROTOR
CONSULT BRC
1. Replace the sensor rotor.
- Front: Refer to BRC-162, "FRONT SENSOR ROTOR : Removal and Installation - Front Sensor Rotor".
cardiagn.com
- Rear: Refer to BRC-162, "REAR SENSOR ROTOR : Removal and Installation - Rear Sensor Rotor". G
2. Erase “Self Diagnostic Result” mode of “ABS”.
3. Turn the ignition switch OFF → ON → OFF.
NOTE:
H
Wait at least 10 seconds after turning ignition switch OFF or ON.
4. Start the engine.
5. Drive the vehicle at approx. 50 km/h (31 MPH) or more for approx. 2 minutes.
NOTE: I
Vehicle must be driven after repair or replacement to erase the previous DTCs.
6. Stop the vehicle.
7. Turn the ignition switch OFF. J
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
8. Start the engine.
NOTE: K
Wait at least 10 seconds after start the engine.
9. Repeat step 7 to 8 two or more times.
10. Select “Self Diagnostic Result” mode of “ABS”. L
Is DTC “C1115” detected?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation". M
NO >> Inspection End.
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content)
STOP LAMP SW
C1116 When stop lamp switch signal is not input when brake pedal operates.
(Stop lamp switch)
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
cardiagn.com
• ABS actuator and electric unit (control unit) power supply sys-
• Harness or connector
tem
• Stop lamp switch signal circuit
• Fuse
• Fusible link
• Battery
• Stop lamp relay (if equipped)
>> GO TO 2.
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF, and wait 10 seconds or more.
2. Start the engine.
NOTE:
Stop the vehicle.
3. Wait 1 minute or more.
NOTE:
Never depress brake pedal.
4. Depress brake pedal by 100 mm (3.94 in) or more, and maintain at that position for a minimum of 1 minute
or more.
5. Release brake pedal, and wait 1 minute or more.
6. Repeat step 4 to 5 ten or more times.
7. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
8. Start the engine.
NOTE:
Wait at least 10 seconds after starting the engine.
9. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1116” detected?
YES-1 >> “C1116” is displayed as “CRNT”: Proceed to BRC-99, "Diagnosis Procedure".
YES-2 >> “C1116” is displayed as “PAST”: Inspection End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-45, "Circuit Inspection".
NO-2 >> Confirmation after repair: Inspection End.
A
NOTE:
DTC “C1116” may be detected when the brake pedal and the accelerator pedal are simultaneously depressed
for 1 minute or more while driving the vehicle. This is not a malfunction. B
1.INTERVIEW FROM THE CUSTOMER
Check if the brake pedal and the accelerator pedal are simultaneously depressed for 1 minute or more while
driving the vehicle. C
Is there such a history?
YES >> GO TO 2.
NO >> GO TO 3. D
2.PERFORM SELF-DIAGNOSIS
CONSULT E
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON. BRC
3. Start the engine.
NOTE:
cardiagn.com
Stop the vehicle. G
4. Depress the brake pedal several times.
5. Turn the ignition switch OFF.
NOTE:
H
Wait at least 10 seconds after turning ignition switch OFF.
6. Start the engine.
NOTE:
Wait at least 10 seconds after starting the engine. I
7. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1116” detected?
YES >> GO TO 3. J
NO >> Inspection End.
3.STOP LAMP FOR ILLUMINATION
K
Depress brake pedal and check that stop lamp turns ON.
Does stop lamp turn ON?
YES >> GO TO 5. L
NO >> Check the stop lamp system. Refer to BRC-99, "Diagnosis Procedure". GO TO 4.
4.CHECK DATA MONITOR (1)
CONSULT M
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE: N
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
O
Stop the vehicle.
4. Select “Data Monitor” mode of “ABS”, check “STOP LAMP SW”. Check that data monitor displays “On” or
“Off” when brake pedal is depressed or released. Refer to BRC-48, "Reference Value".
5. Select “Data Monitor” mode of “ABS”, check “PRESS SENSOR”. Check that data monitor displays “5 bar” P
or less when brake pedal is depressed. Refer to BRC-48, "Reference Value".
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 5.
5.CHECK CONNECTOR
1. Turn the ignition switch OFF.
cardiagn.com
8.CHECK DATA MONITOR (2)
CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
Stop the vehicle.
4. Select “Data Monitor” mode of “ABS”, check “STOP LAMP SW”. Check that data monitor displays “On” or
“Off” when brake pedal is depressed or released. Refer to BRC-48, "Reference Value".
5. Select “Data Monitor” mode of “ABS”, check “PRESS SENSOR”. Check that data monitor displays “5 bar”
or less when brake pedal is depressed. Refer to BRC-48, "Reference Value".
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 9.
9.CHECK STOP LAMP SWITCH
Check the stop lamp switch. Refer to BRC-102, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 10.
NO >> Replace the stop lamp switch. Refer to BR-20, "Exploded View". GO TO 10.
10.CHECK DATA MONITOR (3)
CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
NOTE:
Start the vehicle.
4. Select “Data Monitor” mode of “ABS”, check “STOP LAMP SW”. Check that data monitor displays “On” or
“Off” when brake pedal is depressed or released. Refer to BRC-48, "Reference Value".
5. Select “Data Monitor” mode of “ABS”, check “PRESS SENSOR”. Check that data monitor displays “5 bar”
or less when brake pedal is depressed. Refer to BRC-48, "Reference Value".
Is the inspection result normal?
cardiagn.com
4. Turn the ignition switch OFF → ON → OFF. G
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
5. Start the engine.
NOTE: H
Stop the vehicle.
6. Select “Data Monitor” mode of “ABS”, check “STOP LAMP SW”. Check that data monitor displays “On” or
“Off” when brake pedal is depressed or released. Refer to BRC-48, "Reference Value". I
7. Select “Data Monitor” mode of “ABS”, check “PRESS SENSOR”. Check that data monitor displays “5 bar”
or less when brake pedal is depressed. Refer to BRC-48, "Reference Value".
Is the inspection result normal? J
YES >> Inspection End.
NO >> GO TO 13.
13.CHECK STOP LAMP SWITCH CIRCUIT (1) K
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground. L
ABS actuator and electric unit (control unit) Stop lamp switch
Continuity
Connector Terminal Connector Terminal
E125 17 E38 4 Yes
4. Check the continuity between ABS actuator and electric unit (control unit) harness connector and the
ground.
cardiagn.com
lation".
NO >> Repair / replace harness or connector, and GO TO 16.
15.CHECK DATA MONITOR (5)
CONSULT
1. Connect ABS actuator and electric unit (control unit) harness connector.
2. Connect stop lamp switch harness connector.
3. Erase “Self Diagnostic Result” of “ABS”
4. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
5. Start the engine.
NOTE:
Stop the vehicle.
6. Select “Data Monitor” mode of “ABS”, check “STOP LAMP SW”. Check that data monitor displays “On” or
“Off” when brake pedal is depressed or released. Refer to BRC-48, "Reference Value".
7. Select “Data Monitor” mode of “ABS”, check “PRESS SENSOR”. Check that data monitor displays “5 bar”
or less when brake pedal is depressed. Refer to BRC-48, "Reference Value".
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
Component Inspection INFOID:0000000013841239
BRC
cardiagn.com
G
>> GO TO 2.
2.CHECK DTC DETECTION
cardiagn.com
CONSULT
1. Turn the ignition switch OFF to ON.
2. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1118” detected?
YES >> Proceed to diagnosis procedure. Refer to BRC-104, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure INFOID:0000000013149649
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content) C
FR LH IN ABS SOL
C1120 When a malfunction is detected in front LH ABS IN valve.
(Front LH ABS IN solenoid valve)
FR RH IN ABS SOL D
C1122 When a malfunction is detected in front RH ABS IN valve.
(Front RH ABS IN solenoid valve)
RR LH IN ABS SOL
C1124 When a malfunction is detected in rear LH ABS IN valve.
(Rear LH ABS IN solenoid valve)
E
RR RH IN ABS SOL
C1126 When a malfunction is detected in rear RH ABS IN valve.
(Rear RH ABS IN solenoid valve)
cardiagn.com
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC. G
>> GO TO 2. L
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF. M
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. N
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”. O
Is DTC “C1120”, “C1122”, “C1124” or “C1126” detected?
YES-1 >> “C1120”, “C1122”, “C1124” or “C1126” is displayed by “CRNT”: Proceed to BRC-106, "Diagnosis
P
Procedure".
YES-2 >> “C1120”, “C1122”, “C1124” or “C1126” is displayed by “PAST”: Inspection End (Erase the memory
of “Self Diagnostic Result” mode of “ABS”.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair / replace harness or connector, securely lock the connector, and GO TO 2.
2.PERFORM SELF DIAGNOSTIC RESULT
CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”.
cardiagn.com
Is DTC “C1120”, “C1122”, “C1124” or “C1126” detected?
YES >> GO TO 3.
NO >> Inspection End.
3.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to BRC-140,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair / replace harness, connector, fuse, or fusible link.
4.CHECK TERMINAL
Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with har-
ness connector.
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
NO >> Repair / replace harness, connector, or terminal.
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content) C
FR LH OUT ABS SOL
C1121 When a malfunction is detected in front LH ABS OUT valve.
(Front LH ABS OUT solenoid valve)
FR RH OUT ABS SOL D
C1123 When a malfunction is detected in front RH ABS OUT valve.
(Front RH ABS OUT solenoid valve)
RR LH OUT ABS SOL
C1125 When a malfunction is detected in rear LH ABS OUT valve.
(Rear LH ABS OUT solenoid valve)
E
RR RH OUT ABS SOL
C1127 When a malfunction is detected in rear RH ABS OUT valve.
(Rear RH ABS OUT solenoid valve)
cardiagn.com
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC. G
>> GO TO 2. L
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF. M
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. N
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”. O
Is DTC “C1121”, “C1123”, “C1125” or “C1127” detected?
YES-1 >> “C1121”, “C1123”, “C1125” or “C1127” is displayed by “CRNT”: Proceed to BRC-108, "Diagnosis
P
Procedure".
YES-2 >> “C1121”, “C1123”, “C1125” and “C1127” are displayed by “PAST”: Inspection End (Erase the
memory of “Self Diagnostic Result” mode of “ABS”.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair / replace harness or connector, securely lock the connector, and GO TO 2.
2.SELECT SELF DIAGNOSTIC RESULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1121”, “C1123”, “C1125” or “C1127” detected?
YES >> GO TO 3.
cardiagn.com
NO >> Inspection End.
3.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to BRC-140,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair / replace harness, connector, fuse, or fusible link.
4.CHECK TERMINAL
Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with har-
ness connector.
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
NO >> Repair / replace harness, connector, or terminal.
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content) C
ENGINE SIGNAL 1
C1130 When a malfunction is detected in ECM system.
(Engine system signal)
POSSIBLE CAUSE D
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC. E
cardiagn.com
tem • ABS actuator and electric unit (control unit) power supply sys-
• Fuse tem G
• Fusible link • Fuse
• Battery • Fusible link
• CAN communication line • Battery
• CAN communication line
H
>> GO TO 2.
2.CHECK DTC DETECTION K
CONSULT
1. Turn the ignition switch OFF.
NOTE: L
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE: M
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1130” detected? N
YES-1 >> “CRNT” is displayed: Proceed to BRC-109, "Diagnosis Procedure".
YES-2 >> “PAST” is displayed: Inspection End (Erase the memory of “Self Diagnostic Result” mode of
“ABS”.) O
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure INFOID:0000000013148534
P
cardiagn.com
NO >> Repair / replace harness, connector, or terminal, securely lock the connector, and GO TO 4.
4.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
CONSULT
1. Connect ECM harness connector.
2. Connect ABS actuator and electric unit (control unit) harness connector.
3. Erase “Self Diagnostic Result” mode of “ABS”.
4. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
5. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
6. Repeat step 4 to 5 two or more times.
7. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1130” or “U1000”detected?
YES (“C1130”)>>GO TO 1.
YES (“U1000”)>>Refer to LAN-51, "Trouble Diagnosis Flow Chart".
NO >> Inspection End.
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content) C
ACTUATOR RLY
C1140 When a malfunction is detected in actuator relay.
(Actuator relay)
POSSIBLE CAUSE D
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC. E
cardiagn.com
tem
• Fuse
• Fuse G
• Fusible link
• Fusible link
• Battery
• Battery
>> GO TO 2. J
2.CHECK DTC DETECTION
CONSULT
K
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. L
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times. M
4. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1140” detected?
YES-1 >> “CRNT” is displayed: Proceed to BRC-111, "Diagnosis Procedure". N
YES-2 >> “PAST” is displayed: Inspection End (Erase the memory of “Self Diagnostic Result” mode of
“ABS”.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End. O
P
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair / replace harness or connector, securely lock the connector, and GO TO 2.
cardiagn.com
YES >> GO TO 4.
NO >> Repair / replace harness, connector, fuse, or fusible link.
4.CHECK TERMINAL
Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with har-
ness connector.
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
NO >> Repair / replace harness, connector, or terminal.
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content) C
PRESS SEN CIRCUIT
C1142 When a malfunction is detected in pressure sensor.
(Pressure sensor circuit)
POSSIBLE CAUSE D
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC. E
cardiagn.com
• Stop lamp switch system • Brake system
• ABS actuator and electric unit (control unit) power supply sys- • ABS actuator and electric unit (control unit) power supply sys- G
tem tem
• Fuse • Fuse
• Fusible link • Fusible link
• Battery • Battery H
• Air inclusion in the brake piping
>> GO TO 2.
K
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF. L
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE: M
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”. N
Is DTC “C1142” detected?
YES-1 >> “CRNT” is displayed: Proceed to BRC-113, "Diagnosis Procedure".
YES-2 >> “PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.) O
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure INFOID:0000000013148638 P
cardiagn.com
• Brake pedal assembly: Refer to BR-10, "Inspection" and BR-10, "Adjustment".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Adjust the brake pedal height or replace brake pedal assembly.
• Adjust the brake pedal: Refer to BR-10, "Inspection" and BR-10, "Adjustment".
• Replace the brake pedal: Refer to BR-20, "Removal and Installation".
5.CHECK BRAKE HYDRAULIC BOOSTER ASSEMBLY
Check the brake hydraulic booster assembly. Refer to BR-15, "Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace brake hydraulic booster assembly. Refer to BR-29, "Removal and Installation".
6.CHECK FRONT DISC BRAKE
Check the front disc brake.
• BR-16, "DISC BRAKE ROTOR : Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace front disc brake.
• Refer to BR-36, "DISC BRAKE ROTOR : Removal and Installation".
7.CHECK REAR DISC BRAKE
Check the rear disc brake.
• Refer to BR-40, "DISC BRAKE ROTOR : Exploded View".
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair or replace rear disc brake.
• Refer to BR-41, "DISC BRAKE ROTOR : Removal and Installation".
8.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to BRC-140,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair / replace harness, connector, fuse, or fusible link.
9.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Revision: March 2016 BRC-114 2016 Titan NAM
C1142 PRESS SENSOR
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
CONSULT
1. Erase “Self Diagnostic Result” mode of “ABS”. A
2. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF. B
3. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
4. Repeat step 2 to 3 two or more times. C
5. Start the engine and drive the vehicle for a short period of time.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs. D
6. Stop the vehicle.
7. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1142” detected?
E
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
NO >> Check the ABS actuator and electric unit (control unit) harness connector and terminal for dam-
age, looseness and disconnection. Repair / replace harness, connector, or terminal. BRC
cardiagn.com
G
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content)
ST ANG SEN CIRCUIT
C1143 When a malfunction is detected in steering angle sensor.
(Steering angle sensor circuit)
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
cardiagn.com
• IPDM E/R
tem
• CAN communication line
• Fuse
• Wheel alignment
• Fusible link
• Incomplete neutral position adjustment of steering angle sensor
• Battery
• ABS actuator and electric unit (control unit) power supply sys-
• CAN communication line
tem
• Incomplete neutral position adjustment of steering angle sensor
• Fuse
• Improper installation of steering angle sensor
• Fusible link
• Battery
>> GO TO 2.
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1143” detected?
YES-1 >> “CRNT” is displayed: Proceed to BRC-116, "Diagnosis Procedure".
YES-2 >> “PAST” is displayed: Inspection End.
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure INFOID:0000000013148640
>> GO TO 2. A
2.PERFORM SELF DIAGNOSTIC RESULT (1)
CONSULT B
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF. C
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times. D
4. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1143” detected?
YES-1 >> “CRNT” is displayed: GO TO 3. E
YES-2 >> “PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)
NO >> Inspection End.
3.CHECK CONNECTOR BRC
cardiagn.com
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
3. Check the steering angle sensor harness connector for disconnection or looseness. G
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair / replace harness or connector, securely lock the connector, and GO TO 4. H
cardiagn.com
Is the inspection result normal?
YES >> Perform trouble diagnosis for ignition power supply.
NO >> Repair / replace harness, connector, or fuse.
7.CHECK STEERING ANGLE SENSOR GROUND CIRCUIT
1. Turn the ignition switch OFF.
2. Check the continuity between steering angle sensor harness connector and ground.
BRC
cardiagn.com
G
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content)
ST ANG SEN SIGNAL
C1144 (Steering angle sensor not com- When neutral position adjustment of steering angle sensor is not complete.
plete)
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
cardiagn.com
• ABS actuator and electric unit (control unit)
• Incomplete neutral position adjustment of steering angle sensor
>> GO TO 2.
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1144” detected?
YES-1 >> “CRNT” is displayed: Proceed to BRC-120, "Diagnosis Procedure".
YES-2 >> “PAST” is displayed: Inspection End (Erase the memory of “Self Diagnostic Result” mode of
“ABS”.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure INFOID:0000000013148982
>> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
CONSULT
1. Turn the ignition switch OFF.
CONSULT
cardiagn.com
1. Select “ABS”, “Data Monitor” and “STR ANGLE SIG” in this order.
G
2. Check that the indication changes with the steering angle when the steering wheel is turned left/right from
the neutral position. Refer to BRC-48, "Reference Value".
Is the inspection result normal?
H
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
NO >> Replace the steering angle sensor. Refer to BRC-165, "Removal and Installation".
I
Display item
DTC Malfunction detected condition
(Trouble diagnosis content)
• When a malfunction is detected in yaw rate signal.
• When a signal line of yaw rate/side/decel G sensor is open or shorted.
• When power supply voltage of yaw rate/side/decel G sensor is in following state.
YAW RATE SENSOR
C1145 - Yaw rate/side/decel G sensor power supply voltage: 4.8 V ≥ yaw rate/side/decel G sensor
(Yaw rate sensor circuit)
power supply voltage
- Yaw rate/side/decel G sensor power supply voltage: 5.2 V ≤ yaw rate/side/decel G sensor
power supply voltage
SIDE G-SEN CIRCUIT
C1146 When a malfunction is detected in side G signal.
(Side G sensor circuit)
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
cardiagn.com
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
>> GO TO 2.
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic” mode of “ABS”.
Is DTC “C1145” or “C1146” detected?
YES-1 >> “C1145”, or “C1146” is displayed by “CRNT”: Proceed to BRC-123, "Diagnosis Procedure".
YES-2 >> “C1145”, and “C1146” are displayed by “PAST”: Inspection End (Erase the memory of “Self Diag-
nostic” mode of “ABS”.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
A
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Check the ABS actuator and electric unit (control unit) power supply and ground circuits. Refer to BRC-86, B
"Diagnosis Procedure".
Is the inspection result normal?
C
YES >> GO TO 2.
NO >> Repair / replace harness, connector, fuse, or fusible link.
2.CHECK CONNECTOR D
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
3. Check the yaw rate/side/decel G sensor harness connector for disconnection or looseness. E
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair / replace harness or connector, securely lock the connector, and GO TO 3. BRC
3. PERFORM SELF-DIAGNOSIS
cardiagn.com
CONSULT
1. Turn the ignition switch OFF. G
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. H
NOTE:
Wait at least 10 seconds after start the engine.
3. Select “Self Diagnostic Result” of “ABS”.
I
Is DTC “C1145” or “C1146” detected?
YES >> GO TO 4.
NO >> Inspection End.
J
4.CHECK YAW RATE/SIDE/DECEL G SENSOR POWER SUPPLY CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector. K
3. Disconnect yaw rate/side/decel G sensor harness connector.
4. Check the continuity between yaw rate/side/decel G sensor harness connector and ABS actuator and
electric unit (control unit) harness connector. L
Yaw rate/side/decel G sensor ABS actuator and electric unit (control unit)
Continuity
Connector Terminal Connector Terminal
M
M108 3 E125 18 Yes
Is the inspection result normal?
YES >> GO TO 5. N
NO >> Repair / replace harness or connector.
5.CHECK YAW RATE/SIDE/DECEL G SENSOR GROUND CIRCUIT
O
Check the continuity between yaw rate/side/decel G sensor harness connector and ABS actuator and electric
unit (control unit) harness connector.
Yaw rate/side/decel G sensor ABS actuator and electric unit (control unit)
Continuity
Connector Terminal Connector Terminal
4 9
M108 E125 Yes
5 10
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair / replace harness or connector.
7.CHECK YAW RATE/SIDE/DECEL G SENSOR CIRCUIT
Check the continuity between each terminal of yaw rate/side/decel G sensor harness connector.
cardiagn.com
6−4
6−3
M108 No
3−4
3−5
4−5
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair / replace harness or connector.
8.CHECK YAW RATE/SIDE/DECEL G SENSOR (1)
CONSULT
1. Connect yaw rate/side/decel G sensor harness connector.
2. Connect ABS actuator and electric unit (control unit) harness connector.
3. Turn the ignition switch ON.
NOTE:
Never start the engine.
4. Select “Data Monitor” mode of “ABS”, check “DECEL G-SEN”.
5. Move yaw rate/side/decel G sensor as shown in the figure to
check the output before and after moving the sensor.
Harness connector A
Yaw rate/side/decel G sensor
Connector Terminal
3 3
B
4 4
M108
5 5
6 6 C
3. Turn the ignition switch ON.
NOTE:
Never start the engine. D
4. Check the voltage between yaw rate/side/decel G sensor harness connector terminals.
CAUTION:
Never short out the terminals while measuring voltages. E
cardiagn.com
5–6 0.5 – 2.5 V
G
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
H
NO >> Replace the yaw rate/side/decel G sensor. Refer to BRC-166, "Removal and Installation".
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content)
BR FLUID LEVEL LOW • When brake fluid level low signal is detected.
C1155
(Brake fluid level low) • When an open circuit is detected in brake fluid level switch circuit.
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
cardiagn.com
• Combination meter
• Brake fluid level is low
• Unified meter and A/C amp.
• IPDM E/R
• Brake fluid level is low
>> GO TO 2.
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1155” detected?
YES-1 >> “CRNT” is displayed: Proceed to BRC-126, "Diagnosis Procedure".
YES-2 >> “PAST” is displayed: Inspection End (Erase the memory of “Self Diagnostic Result” mode of
“ABS”.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure INFOID:0000000013148984
cardiagn.com
YES >> GO TO 5. G
NO >> Repair / replace harness or connector, and GO TO 4.
4.PERFORM SELF DIAGNOSTIC RESULT (2) H
CONSULT
1. Turn the ignition switch OFF.
NOTE: I
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine. J
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1155” detected? K
YES >> GO TO 5.
NO >> Inspection End.
5.CHECK BRAKE FLUID LEVEL SWITCH L
Check the brake fluid level switch. Refer to BR-42, "Exploded View".
Is the inspection result normal?
M
YES >> GO TO 7.
NO >> Replace the reservoir tank. Refer to BR-42, "Disassembly and Assembly". GO TO 6.
6.PERFORM SELF DIAGNOSTIC RESULT (3) N
CONSULT
1. Erase “Self Diagnostic Result” mode of “ABS”.
2. Turn the ignition switch OFF → ON → OFF. O
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
P
NOTE:
Wait at least 10 seconds after start the engine.
4. Repeat step 2 to 3 two or more times.
5. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1155” detected?
YES >> GO TO 7.
NO >> Inspection End.
cardiagn.com
Wait at least 10 seconds after start the engine.
4. Repeat step 2 to 3 two or more times.
5. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1155” detected?
YES >> GO TO 9.
NO >> Inspection End.
9.CHECK BRAKE FLUID LEVEL SWITCH CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect brake fluid level switch harness connector.
3. Disconnect ABS actuator and electric unit (control unit) harness connector.
4. Check the continuity between brake fluid level switch harness connector and ABS actuator and electric
unit (control unit) harness connector.
Brake fluid level switch ABS actuator and electric unit (control unit)
Continuity
Connector Terminal Connector Terminal
E21 2 M125 13 Yes
5. Check the continuity between brake fluid level switch harness connector and ground.
Check the combination meter. Refer to MWI-27, "CONSULT Function (METER/M&A)" (Type A) or MWI-131,
"CONSULT Function (METER/M&A)" (Type B).
B
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
C
NO >> Repair or replace combination meter. Refer to MWI-108, "Removal and Installation" (Type A) or
MWI-186, "Removal and Installation" (Type B).
Component Inspection INFOID:0000000013148985
D
cardiagn.com
When brake fluid level in reservoir tank is within the specified level. No G
1–2
When brake fluid level in reservoir tank is less than the specified level. Yes
Is the inspection result normal? H
YES >> Inspection End.
NO >> Replace the reservoir tank. Refer to BR-42, "Disassembly and Assembly".
I
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content)
DECEL G SEN SET
C1160 When calibration of yaw rate/side/decel G sensor is not complete.
(Decel G sensor set)
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
cardiagn.com
• Fuse • ABS actuator and electric unit (control unit)
• Fusible link
• Battery
>> GO TO 2.
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic” mode of “ABS”.
Is DTC “C1160” detected?
YES-1 >> “CRNT” is displayed: Proceed to BRC-130, "Diagnosis Procedure".
YES-2 >> “PAST” is displayed: Inspection End (Erase the memory of “Self Diagnostic” mode of “ABS”.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure INFOID:0000000013148996
>> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
CONSULT
1. Turn the ignition switch OFF.
BRC
cardiagn.com
G
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content)
CV 1
C1164 When a malfunction is detected in cut valve 1.
(Cut valve 1)
CV 2
C1165 When a malfunction is detected in cut valve 2.
(Cut valve 2)
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
cardiagn.com
• Harness or connector
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit (control unit) power supply sys-
• ABS actuator and electric unit (control unit) power supply sys-
tem
tem
• Fuse
• Fuse
• Fusible link
• Fusible link
• Battery
• Battery
>> GO TO 2.
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1164” or “C1165” detected?
YES-1 >> “C1164” or “C1165” is displayed by “CRNT”: Proceed to BRC-132, "Diagnosis Procedure".
YES-2 >> “C1164” and “C1165” are displayed by “PAST”: Inspection End (Erase the memory of “Self Diag-
nostic Result” mode of “ABS”.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure INFOID:0000000013148998
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with har-
cardiagn.com
ness.
G
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
H
NO >> Repair / replace harness, connector, or terminal.
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content)
SV 1
C1166 When a malfunction is detected in suction valve 1.
(Suction valve 1)
SV 2
C1167 When a malfunction is detected in suction valve 2.
(Suction valve 2)
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
cardiagn.com
• Harness or connector
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit (control unit) power supply sys-
• ABS actuator and electric unit (control unit) power supply sys-
tem
tem
• Fuse
• Fuse
• Fusible link
• Fusible link
• Battery
• Battery
>> GO TO 2.
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1166” or “C1167” detected?
YES-1 >> “C1166” or “C1167” is displayed by “CRNT”: Proceed to BRC-134, "Diagnosis Procedure".
YES-2 >> “C1166” and “C1167” is displayed by “PAST”: Inspection End. (Erase the memory of “Self Diag-
nostic Result” mode of “ABS”.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure INFOID:0000000013149000
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.
Is the inspection result normal?
Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with har-
cardiagn.com
ness.
G
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
H
NO >> Repair / replace harness, connector, or terminal.
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content)
VARIANT CODING
C1170 When the information in ABS actuator and electric unit (control unit) is not the same.
(Variant coding)
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
cardiagn.com
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after start the engine.
3. Select “Self Diagnostic Result” mode of “ABS”.
Is DTC “C1170” detected?
YES-1 >> “CRNT” is displayed: Proceed to BRC-136, "Diagnosis Procedure".
YES-2 >> “PAST” is displayed: Inspection End (Erase “Self Diagnostic Result” mode of “ABS”)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure INFOID:0000000013149002
>> Replace the ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Instal-
lation".
cardiagn.com
NO >> Inspection End. G
Diagnosis Procedure INFOID:0000000013149651
CONSULT
Select “Self Diagnostic Result” mode of “DIFF LOCK”.
I
Is any DTC detected?
YES >> Check the DTC.
NO >> GO TO 2.
J
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
CONSULT
1. Erase “Self Diagnostic Result” of “ABS”. K
2. Turn the ignition switch OFF.
3. Start the engine and drive the vehicle for a short period of time.
4. After the vehicle stops, select “Self Diagnostic Result” mode of “ABS”. L
Is DTC “C1118” detected?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Installa-
tion". M
NO >> Check pin terminals and connection of each harness connector for abnormal conditions. Repair or
replace error-detected parts.
N
cardiagn.com
CAUTION:
The VDC warning lamp, ABS warning lamp and brake warning lamp turns ON and DTC “C118E” may
be detected in self-diagnosis result of “ABS” when the brake pedal is excessively operated, such as
air bleeding. This is not a system malfunction because this occurs due to the temporary decrease in
accumulator fluid pressure. The system returns to normal condition when the accumulator fluid pres-
sure reaches the specified pressure with the ignition switch ON and the VDC warning lamp, ABS warn-
ing lamp, and brake warning lamp turn OFF. After these steps, ABS self-diagnosis results are erased.
CONSULT
1. Erase “Self Diagnostic Result” mode of “ABS”.
2. Turn the ignition switch OFF.
3. Depress brake pedal to full stroke 20 times or more.
4. Start the engine, and then wait 2 minutes or more.
5. Check VDC warning lamp, ABS warning lamp and brake warning lamp turns OFF.
6. Select “Self Diagnostic Result” mode of “ABS”.
Is any DTC detected?
YES >> Check the DTC. Refer to BRC-55, "DTC Index".
NO >> Inspection End.
Display Item
DTC Malfunction detected condition
(Trouble diagnosis content) C
CAN COMM CIRCUIT When CAN communication signal is not continuously transmitted or received for 2 sec-
U1000
(CAN communication circuit) onds or more.
POSSIBLE CAUSE D
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC. E
cardiagn.com
G
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test. H
>> GO TO 2.
2.CHECK DTC DETECTION I
CONSULT
1. Turn the ignition switch OFF. J
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE: K
Wait at least 10 seconds after start the engine.
3. Repeat step 1 to 2 two or more times.
4. Select “Self Diagnostic Result” mode of “ABS”. L
Is DTC “U1000” detected?
YES-1 >> “CRNT” is displayed: Proceed to BRC-139, "Diagnosis Procedure".
YES-2 >> “PAST” is displayed: Inspection End (Erase the memory of “Self Diagnostic Result” mode of M
“ABS”.)
NO-1 >> To check malfunction symptom before repair: Refer to GI-43, "Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
N
Diagnosis Procedure INFOID:0000000013149645
1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) IGNITION POWER SUPPLY (1)
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connectors.
3. Check the voltage between ABS actuator and electric unit (control unit) harness connectors and ground.
E125 18 Ground 0V
4. Turn the ignition switch ON
NOTE:
Start the engine.
5. Check the voltage between ABS actuator and electric unit (control unit) harness connectors and ground.
cardiagn.com
Connector Terminal (Approx.)
ABS actuator and electric unit (control unit) Fuse block (J/B)
Continuity
Connector Terminal Connector Terminal
E125 18 E119 15 Yes
6. Check the continuity between ABS actuator and electric unit (control unit) harness connectors and
ground.
cardiagn.com
NO >> Repair / replace harness, connector, or fusible link.
G
5. CHECK ACTUATOR RELAY, ABS IN VALVE, ABS OUT VALVE POWER SUPPLY
1. Turn the ignition switch OFF.
2. Check the voltage between ABS actuator and electric unit (control unit) harness connector and ground. H
7.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) GROUND CIRCUIT
Check the continuity between ABS actuator and electric unit (control unit) harness connector and the ground.
cardiagn.com
cardiagn.com
nector.
3. Check connectors and terminals for deformation, disconnection, looseness or damage. G
Is the inspection result normal?
YES >> GO TO 2. H
NO >> Repair or replace as necessary.
2.CHECK PARKING BRAKE SWITCH
Check parking brake switch. Refer to PB-5, "Inspection". I
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace parking brake switch. Refer to PB-11, "Removal and Installation". J
3.CHECK PARKING BRAKE SWITCH SIGNAL
CONSULT. K
1. Connect combination meter connector M24 (Type A) or M163 (Type B) and parking brake switch connec-
tor.
2. Turn ignition switch ON.
3. In “Data Monitor” mode select “PARK BRAKE SW” and check parking brake switch signal. L
cardiagn.com
1. Turn ignition switch OFF.
2. Disconnect parking brake switch connector.
3. Check continuity between parking brake switch terminal 1 and ground.
cardiagn.com
3. Check connectors and terminals for deformation, disconnection, looseness or damage.
G
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace as necessary. H
2.CHECK VDC OFF SWITCH
Check VDC OFF switch. Refer to BRC-13, "VDC OFF Switch".
Is the inspection result normal? I
YES >> GO TO 3.
NO >> Replace VDC OFF switch.
J
3.CHECK VDC OFF SWITCH SIGNAL
CONSULT.
1. Connect ABS actuator and electric unit (control unit) connector E125 and VDC OFF switch connector. K
2. Turn ignition switch ON.
3. In “Data Monitor” mode select “OFF SW” and check VDC OFF switch signal.
L
Condition DATA MONITOR
VDC OFF switch is pressed and released On
VDC OFF switch is pressed and released again Off M
Is the inspection result normal?
YES >> Refer to BRC-66, "Work Flow".
NO >> GO TO 4. N
4.CHECK VDC OFF SWITCH CIRCUIT
1. Turn ignition switch OFF. O
2. Disconnect ABS actuator and electric unit (control unit) connector E125 and VDC OFF switch connector.
3. Check continuity between ABS actuator and electric unit (control unit) connector E125 terminal 39 and
VDC OFF switch connector M148 terminal 6.
P
ABS actuator and electric unit (control unit) VDC OFF switch
Continuity
Connector Terminal Connector Terminal
E125 39 M148 6 Yes
4. Check continuity between ABS actuator and electric unit (control unit) connector terminal E125 terminal
39 and ground.
cardiagn.com
Component Inspection INFOID:0000000013123990
cardiagn.com
2.CHECK COMBINATION METER G
Check if indication and operation of combination meter are normal. Refer to MWI-14, "METER SYSTEM : Sys-
tem Description" (Type A) or MWI-120, "METER SYSTEM : System Description" (Type B).
H
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-108, "Removal and Installation" (Type A) or MWI-186, I
"Removal and Installation" (Type B).
cardiagn.com
CONSULT.
Select “Self Diagnostic Result” mode of “METER/M&A”.
Are any DTCs detected?
YES >> Refer to MWI-35, "DTC Index" (Type A) or MWI-139, "DTC Index" (Type B).
NO >> GO TO 2.
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-14, "METER SYSTEM : Sys-
tem Description" (Type A) or MWI-120, "METER SYSTEM : System Description" (Type B).
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-108, "Removal and Installation" (Type A) or MWI-186,
"Removal and Installation" (Type B).
cardiagn.com
2.CHECK COMBINATION METER G
Check if indication and operation of combination meter are normal. Refer to MWI-14, "METER SYSTEM : Sys-
tem Description" (Type A) or MWI-120, "METER SYSTEM : System Description" (Type B).
H
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-108, "Removal and Installation" (Type A) or MWI-186, I
"Removal and Installation" (Type B).
cardiagn.com
2.CHECK COMBINATION METER
Check if indication and operation of combination meter are normal. Refer to MWI-14, "METER SYSTEM : Sys-
tem Description" (Type A) or MWI-120, "METER SYSTEM : System Description" (Type B).
Is the inspection result normal?
YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Installa-
tion".
NO >> Replace combination meter. Refer to MWI-108, "Removal and Installation" (Type A) or MWI-186,
"Removal and Installation" (Type B).
SYMPTOM DIAGNOSIS A
VDC/TCS/ABS
Symptom Table INFOID:0000000013123999
B
If ABS warning lamp and SLIP indicator lamp turn ON, perform self-diagnosis.
cardiagn.com
Pedal vibration or ABS operation sound Brake pedal BRC-156, "Diag-
occurs (Note 2) ABS actuator and electric unit (control unit) nosis Procedure" G
1.CHECK START
Check front and rear brake force distribution using a brake tester.
Is the inspection result normal?
YES >> GO TO 2
NO >> Check brake system.
2.CHECK FRONT AND REAR AXLE
Make sure that there is no excessive play in the front and rear axles. Refer to front: FSU-6, "Inspection", rear:
RSU-5, "Inspection".
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace malfunctioning components.
3.CHECK WHEEL SENSOR AND SENSOR ROTOR
Check the following:
cardiagn.com
• Wheel sensor installation for damage
• Sensor rotor installation for damage
• Wheel sensor connector
• Wheel sensor harness
Is the inspection result normal?
YES >> GO TO 4
NO >> • Replace wheel sensor BRC-162, "FRONT SENSOR ROTOR : Removal and Installation - Front
Sensor Rotor" (front wheel sensor) or BRC-160, "REAR WHEEL SENSOR : Removal and
Installation" (rear wheel sensor).
• Replace sensor rotor BRC-162, "FRONT SENSOR ROTOR : Removal and Installation - Front
Sensor Rotor" (front sensor rotor) or BRC-162, "REAR SENSOR ROTOR : Removal and Instal-
lation - Rear Sensor Rotor" (rear sensor rotor).
• Repair harness.
4.CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp is turned off after the ignition switch is turned ON or when driving.
Is the inspection result normal?
YES >> Inspection End.
NO >> Perform self diagnostic result. Refer to BRC-43, "CONSULT Function (ABS)".
cardiagn.com
NO >> Check brake system.
G
CAUTION:
The stopping distance on slippery road surfaces might be longer with the ABS operating than when
the ABS is not operating.
1.CHECK ABS FUNCTION
1. Turn ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) connector to deactivate ABS.
3. Check stopping distance.
4. After inspection, connect connector.
Is the inspection result normal?
YES >> Inspection End.
NO >> Check brake system.
cardiagn.com
CAUTION: B
ABS does not operate when speed is 10 km/h (6 MPH) or lower.
1.CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp turns OFF after ignition switch is turned ON or when driving. C
Is the inspection result normal?
YES >> Inspection End.
NO >> Perform “Self Diagnostic Result” of “ABS”. Refer to BRC-43, "CONSULT Function (ABS)". D
BRC
cardiagn.com
G
CAUTION:
Under the following conditions, ABS is activated and vibration is felt when brake pedal is lightly
depressed (just place a foot on it).However, this is normal.
• When shifting gears
• When driving on slippery road
• During cornering at high speed
• When passing over bumps or grooves [approximately 50 mm (1.97 in) or more]
• When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or higher]
1.SYMPTOM CHECK 1
Check that there are pedal vibrations when the engine is started.
Do symptoms occur?
YES >> GO TO 2
NO >> Inspect the brake pedal.
2.SYMPTOM CHECK 2
Check that there are ABS operation noises when the engine is started.
cardiagn.com
Do symptoms occur?
YES >> GO TO 3
NO >> Perform “Self Diagnostic Result” of “ABS”. Refer to BRC-43, "CONSULT Function (ABS)".
3.SYMPTOM CHECK 3
Check symptoms when electrical component (headlamps, etc.) switches are operated.
Do symptoms occur?
YES >> Check if there is a radio, antenna, antenna lead wire, or wiring close to the control unit. If there is,
move it farther away.
NO >> Inspection End.
1.SYMPTOM CHECK B
Check if the vehicle jerks during VDC/TCS/ABS control.
Is the inspection result normal?
C
YES >> Inspection End.
NO >> GO TO 2
2.CHECK SELF DIAGNOSTIC RESULT D
Select “Self Diagnostic Result” mode of “ABS”. Refer to BRC-43, "CONSULT Function (ABS)".
Are self diagnostic results indicated?
YES >> Check corresponding items, make repairs, and perform ABS actuator and electric unit (control E
unit) self diagnostic result again. Refer to BRC-43, "CONSULT Function (ABS)".
NO >> GO TO 3
3.CHECK CONNECTOR BRC
1. Turn ignition switch OFF.
cardiagn.com
2. Disconnect ABS actuator and electric unit (control unit) connector.
3. Check terminals for deformation, disconnection, looseness, etc. G
4. Securely connect connector and perform “Self Diagnostic Result” mode of “ABS”. Refer to BRC-43,
"CONSULT Function (ABS)".
Are self diagnostic results indicated? H
YES >> If poor contact, damage, open or short circuit of connector terminal is found, repair or replace.
NO >> GO TO 4
4.CHECK ECM AND TCM SELF DIAGNOSTIC RESULT I
1. Select“Self Diagnostic Result” mode of “ECM”. Refer to EC-103, "CONSULT Function" (Cummins 5.0L) or
EC-1325, "CONSULT Function" (VK56VD).
2. Select “Self Diagnostic Result” mode of “TCM”. Refer to TM-42, "CONSULT Function" (RE6R01A) or TM- J
316, "CONSULT Function" (RE7R01B).
Are self diagnostic results indicated?
YES >> Check the corresponding items. K
• ECM: Refer to EC-135, "DTC Index" (Cummins 5.0L) or EC-1366, "DTC Index" (VK56VD).
• TCM: Refer to TM-68, "DTC Index" (RE6R01A) or TM-333, "DTC Index" (RE7R01B) .
NO >> Replace ABS actuator and electric unit (control unit). Refer to BRC-163, "Removal and Installa- L
tion".
Symptom Result
Slight vibrations are felt on the brake pedal and the operation noises occur, when VDC, TCS or ABS is acti-
vated.
This is a normal condi-
Stopping distance is longer than that of vehicles without ABS when the vehicle drives on rough, gravel, or
tion due to the VDC,
snow-covered (fresh, deep snow) roads.
TCS or ABS activation.
The brake pedal moves and generates noises, when TCS or VDC is activated due to rapid acceleration or
sharp turn.
This is normal, and it is
The brake pedal vibrates and motor operation noises occur from the engine room, after the engine starts and
caused by the ABS op-
just after the vehicle starts.
eration check.
Depending on the road conditions, the driver may experience a sluggish feel. This is normal, because
TCS places the highest
TCS may activate momentarily if wheel speed changes when driving over location where friction coefficient priority on the optimum
varies, when downshifting, or when fully depressing accelerator pedal. traction (stability).
The ABS warning lamp and SLIP indicator lamp may turn ON when the vehicle is subject to strong shaking
cardiagn.com
or large vibration, such as when the vehicle is rotating on a turntable or located on a ship while the engine In this case, restart the
is running. engine on a normal
road. If the normal con-
VDC may not operate normally or the ABS warning lamp and SLIP indicator lamp may illuminate, when run-
dition is restored, there
ning on a special road that is extremely slanted (e.g. bank in a circuit course).
is no malfunction. At
A malfunction may occur in the yaw rate/side/decel G sensor system, when the vehicle turns sharply, such that time, erase the self-
as during a spin turn, axle turn, or drift driving, while the VDC function is OFF (VDC OFF indicator lamp illu- diagnosis memory.
minated).
Normal (Deactivate the
VDC/TCS function be-
The vehicle speed will not increase even though the accelerator pedal is depressed, when inspecting the
fore performing an in-
speedometer on a 2-wheel chassis dynamometer.
spection on a chassis
dynamometer.)
This is not a VDC sys-
tem error but results
SLIP indicator lamp may simultaneously turn ON when low tire pressure warning lamp turns ON.
from characteristic
change of tire.
BRC
cardiagn.com
G
K
AWFIA1229ZZ
M
CAUTION:
Do not damage front wheel sensor or sensor rotor.
REMOVAL N
1. Remove the front disc brake rotor. Refer to BR-36, "DISC BRAKE ROTOR : Removal and Installation".
2. Disconnect harness connector from front wheel sensor.
3. Remove front wheel sensor from front wheel sensor brackets and clips. O
4. Remove front wheel sensor bolt and remove front wheel sensor.
CAUTION:
Pull out front wheel sensor being careful to turn it as little as possible. Do not pull on front wheel P
sensor harness.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Before installing, make sure there is no foreign material, such as iron fragments, adhered to pick-up
part of front wheel sensor.
JPFIC0209ZZ
ALFIA0647ZZ
cardiagn.com
1. Rear wheel sensor (LH) 2. Rear wheel sensor (RH) A. Harness connector
CAUTION:
Do not damage rear wheel sensor or sensor rotor.
REMOVAL
1. Disconnect harness connector from rear wheel sensor.
2. Remove rear wheel sensor from rear wheel sensor brackets and clips.
3. Remove rear wheel sensor bolt and remove rear wheel sensor.
BRC
cardiagn.com
JPFIC0209ZZ
G
The front wheel sensor rotor is an integral part of the wheel hub and bearing and cannot be disassembled.
Refer to FAX-7, "Removal and Installation".
The rear wheel sensor rotor is an integral part of the axle shaft and cannot be disassembled. Refer to RAX-6,
"Removal and Installation".
cardiagn.com
REMOVAL B
1. Remove the hydraulic booster assembly. Refer to BR-29, "Removal and Installation".
2. Remove the brake tube using flare nut wrench.
CAUTION: C
Do not scratch the flare nut or the brake tube.
3. Remove the cap and bushing from the brake booster bracket D
using a suitable tool (A).
BRC
cardiagn.com
JPFIA0752ZZ
G
JPFIA0751ZZ
K
5. Remove motor/accumulator assembly from ABS actuator and electric unit (control unit).
INSTALLATION
L
Installation is in the reverse order of removal.
CAUTION:
• To install, use a flare nut crowfoot and torque wrench.
• Always tighten brake tubes to specification when installing. M
• Do not reuse drained brake fluid.
• After installation of the ABS actuator and electric unit (control unit), perform the following.
- Refill brake system with new brake fluid. Then bleed the air from the system. Refer to BR-13, "Bleed-
N
ing Brake System".
- Adjust the steering angle sensor. Refer to BRC-70, "Description".
- Calibrate the yaw rate/side/decel G sensor. Refer to BRC-72, "Description".
- Perform calibration to the ABS actuator and electric unit (control unit). Refer to BRC-69, "Descrip- O
tion".
- Perform additional service when replacing the ABS actuator and electric unit (control unit). Refer to
BRC-69, "Description". P
REMOVAL
1. Remove the hydraulic booster assembly. Refer to BR-29, "Removal and Installation".
2. Remove the brake tube using flare nut wrench.
CAUTION:
Do not scratch the flare nut or the brake tube.
3. Remove the cap and bushing from the brake booster bracket
using a suitable tool (A).
cardiagn.com
JPFIA0752ZZ
JPFIA0751ZZ
5. Remove motor/accumulator assembly from ABS actuator and electric unit (control unit).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• To install, use a flare nut crowfoot and torque wrench.
• Always tighten brake tubes to specification when installing.
• Do not reuse drained brake fluid.
• After installation of the ABS actuator and electric unit (control unit), perform the following.
- Refill brake system with new brake fluid. Then bleed the air from the system. Refer to BR-13, "Bleed-
ing Brake System".
- Adjust the steering angle sensor. Refer to BRC-70, "Description".
- Calibrate the yaw rate/side/decel G sensor. Refer to BRC-72, "Description".
- Perform calibration to the ABS actuator and electric unit (control unit). Refer to BRC-69, "Descrip-
tion".
- Perform additional service when replacing the ABS actuator and electric unit (control unit). Refer to
BRC-69, "Description".
BRC
cardiagn.com
G
cardiagn.com
ALFIA0648ZZ
REMOVAL
1. Remove center console. Refer to IP-24, "Removal and Installation".
2. Remove yaw rate/side/decel G sensor nuts.
CAUTION:
• Do not use power tools to remove the yaw rate/side/decel G sensor.
• Do not drop or strike the yaw rate/side/decel G sensor.
3. Disconnect harness connector from yaw rate/side/decel G sensor and remove the yaw rate/side/decel G
sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not drop or strike the yaw rate/side/decel G sensor.
• After installation, calibrate the yaw rate/side/decel G sensor. Refer to BRC-72, "Description".
BRC
ALLIA1918ZZ
cardiagn.com
1. A/C switch assembly 2. Cluster lid C 3. Switch carrier G
4. VDC OFF switch 5. Sonar system off switch (if equipped) 6. Hazard switch
7. Blind spot warning switch (if 8. Heated steering wheel switch (if equipped) Front
equipped) H
I
REMOVAL
1. Remove cluster lid C. Refer to IP-20, "Removal and Installation".
2. Remove screws (A) and switch carrier (1) from cluster lid C. J
ALJIA1927ZZ
M
3. Release pawls using suitable tool and remove VDC OFF switch
from switch carrier. N
: Pawl
O
ALJIA1522ZZ
INSTALLATION
Installation is in the reverse order of removal.
cardiagn.com
AWFIA1246ZZ
1. Front fog lamp switch (if equipped) 2. AC 120v outlet main switch (if 3. Cargo lamp switch
equipped)
4. Mask 5. Upper switch carrier 6. Lower switch carrier
7. Headlamp aiming switch (if equipped) 8. Differential lock mode switch 9. Hill descent control switch
(if equipped)
10. Mask 11. Instrument lower panel LH Front
REMOVAL
1. Remove instrument lower panel LH. Refer to IP-22, "Removal and Installation".
2. Remove screws from lower switch carrier.
3. Remove lower switch carrier from instrument lower panel LH.
4. Release pawls using suitable tool and remove hill descent
switch from switch carrier.
: Pawl
ALJIA1522ZZ
INSTALLATION
Installation is in the reverse order of removal.