TLT-2H User Manual V500
TLT-2H User Manual V500
The TLT-2H GPS/GSM Tracker is a Vehicle Positioning Device what based on GPS and
GSM/GPRS technology . It's can transmit the Longitude and Latitude coordinates to your Mobile
Phone by SMS. And you can find the detail location of this unit on the Google Map or other Map
Software. Also The tracker can upload the positioning data to the server.through GPRS . So The
user can look for Real-Time Location-Tracking, Historical Tracking through the Internet.
The GPS and GSM Antenna is internal of this unit. So it's very easy to installation. And It's can
use for Car, Truck, Motorcycle ,Bicycle etc...
Before you use this unit, please spend some time to read the User Manual to know the operation
way.
二. Features
三. TLT-2H Picture
2
3.1. Specification
3.2. Others
3
Humidity 5%To 95% Non-condensing
Dimension 88mm×46mm×18mm
Voltage 12-24V
Average Current When stand-by <84mA
Green/ Blue/ Red LED showing GPS、GSM and
LED
power status
Out set SOS Key One SOS emergency key: for urgent call
State Means
State Means
State Means
四.Products Appendix
六. Installation Diagrame
The external 5 wires of TLT-2H GPS/GSM tracker are as follows. Red for the 12V car power
wire, connect to the car battery anode; Black for the earth GND, connect to the car battery cathode;
Yellow for the SOS for help Control wire, connect external SOS switch button to car battery
cathode; Green wire connect ACC car power supply, that is, with the car CD, radio, and other
automotive electrical appliances in parallel. When the vehicle key puts in the ACC gear, the green
line will examine the 12v voltage, the terminal will open the charge function automatically. White
for cut-off oil and power control wire, connect to the relay coil 86, i.e. one end. Relay 85, i.e. anther
end connects to oil and power supply 12V. 30, 87a are normal closed-end, series in the oil and
power supply circuit. Please note that if the installation of lead wire is right, if errors installation led
to the equipment damage, At Own Risk, the company is not responsible for it.
5
七.Application
After you see the brief introduction of this unit, now please see the detail
6
Before you use TLT-2H, you need be the host of TLT-2H, then can control
TLT--2H. so you need save your phone number in the TLT-2H before you
7
Generally Application of SMS Mode
1.1 Single localization request instruction
Format: 666+ user password (4 figures)
eg: 6660000
Explanation: When TLT-2H tracker receives the instruction and confirms the user password correctly,
reads the GPS information. No matter whether effective, the information with the replying base
station which is the set of the original software will be sent to the sender.
Data format:
Lat: Latitude Direction (+/-) Latitude Value (Accuracy for 5 after the decimal point)
Long: Longitude Direction (+/-) Longitude Value (Accuracy for 5 after the decimal point)
Speed: Speed KM/H (Accuracy for 2 after the decimal point)
Direction: Direction (Accuracy for 2 after the decimal point)
Date: Date YYYY-MM-DD
Time: Time HH:MM:SS (GMT)
BS: Base Station information
Fix: Location state (A/V)
ID: IMEI
STATE: Message state
Effective data format:
Lat: +22.50500
Long: +114.01000
Speed: 0.00KM/H
Direction: 315.00
Date: 2008-04-25
Time: 16:39:45
BS: 25ee0dff
Fix: A
ID: 353686009002030
STATE: SMS
Invalid data format:
8
Lat: +22.50500
Long: +114.01000
Speed: 0.00KM/H
Direction: 315.00
Date: 2008-04-25
Time: 16:39:45
BS: 25ee0dff
Fix: V
ID: 353686009002030
STATE: SMS
Note: If in the cold start and GPS no position, it will return to the void of information:
eg: ERROR GPS GPRMC FRAME DATA
BS: 27971054”
ID: 353686009002030
STATE: SMS
9
(Note: pay attention to change the position date format)
Or you can start the internet explorer and copy http://maps.google.com to connect to Google map
website for displaying the location map.
3)You can get the latitude & longitude date by sending “666+password” SMS command code to the
GPS tracker TLT-2H . Input the latitude and longitude that you receive from SMS and click on
search button, the Google earth will display the location map for you.
eg: You receive the information from the tracker. As follows:
Lat: +22.50500
Long: +114.01000
Speed: 0.00KM/H
Direction: 315.00
Date: 2008-04-25
Time: 16:39:45
BS: 25ee0dff
Fix: A
ID: 353686009002030
STATE: SMS
Search the position on the Google map, in relevant position input:
+22.50500 +114.01000
Obtain the following picture:
10
Or you can use local map software on PDA or car navigation device, input the position date. (Note:
pay attention to change the position date format)
Attention: this function is certain risk, it's will happen traffic in the freeway if you send this
command, so please consider again and again.
13
8. Send the positional information in fixed time instruction
Format: 4 xx + user password (4 figures)
eg: 4010000
Explanation: x indicates one figure from 0 to 9, while “xx <60”, its unit is minute. while “xx >60”,
its numerical value is “xx minus 60” and unit is hour, in other words, 61 is 1 hour, 62 is 2 hours,
followed by analogy. When TLT-2H tracker receives the instruction and confirms the user
password correctly, it establishes the current time for initial timing time, xx is the gap time, and
sends the confirmation SMS to the sender’s mobile phone (TIMER START, REPEAT INTERVAL :<
X>MINUTES). Then start to time and send the format as 1.1 setting information when it arrives the
gap time, the information state item automatically updates STATE: TIMER. When “xx=00”, cancels
the positional information in fixed time instruction, and sends the confirmation SMS to the sender’s
mobile phone “TIMER STOP”.
Attention : the interval time can't above 2hours of this version at the moment, if you need long
interval time, please contact us, so we can design this for you .
9. Calling switch instruction
Calling OFF format: 150 + user password (4 figures)
eg: 1500000
Calling ON format: 151 + user password (4 figures)
eg: 1510000
Explanation: When TLT-2H tracker receives the instruction to close calling and confirms the
user password correctly, close the calling function (including the SOS, alarm when across the fence,
and alarm when cut off power), after successfully, sent the confirm information "SET VOICE CALL:
OFF" to the sender. When TLT-2H receives instruction to open calling and confirm the user
password correctly, open the calling function (including the SOS, alarm when across the fence), after
successfully, sent the confirm information "SET VOICE CALL: ON" to the sender.
15
automatically updates STATE: OS. At the same time, call the first user telephone number. If it is
unsuccessful (closed or unable to connect or no response), makes vibration and starts calling the
second and the third in turn.
When the TLT-2H re-enters the fenced area, it will immediately send location information format
4.1.6 to the three preset numbers. The information state item prompts STATE: RS. At the same time,
call the first user telephone number. If it is unsuccessful (closed or unable to connect or no
response), makes vibration and starts calling the second and the third in turn.
1) Set the scope of the fence
According to the input formats different of coordinates, user can choose the format as follows
instructions to operate.
Format1:003+ user password E/Wdddmm.mmmmN/Sdd.mmmmRzzz.z
eg: 003xxxxE11406.0024N2233.4230R1
Explanation: E-- east longitude; W-- west longitude; N-- north latitude; S-- south latitude. In
this example, uses E and N, please according to the actual geographical position choose
corresponding coordinate form to set. In the demonstration, meanings of various parts are as
follows:
Edddmm.mmmm is longitude information with units of degrees and minutes, and the ddd
expresses degree, mm.mmmm expresses minute (Accuracy for 4 after the decimal point, the
following zero cannot bypass)
Ndd.mmmm is latitude information with units of degrees and minutes and the dd expresses
degree, mm.mmmm expresses minute (Accuracy for 4 after the decimal point, the following zero
cannot bypass)
Rzzz.z is radius for the domain (999.9 - 0.1), unit for KM.
When the tracker receives this instruction, judges to be authorized users and confirms the user
password correctly, it will send the confirmation messages “SET GEO-FENCE OK” to the sender.
Format2:004+ user password E/Wddd.dddddN/Sdd.dddddRzzz.z
eg:0040000E114.10004N22.55705R999.9
Explanation: E-- east longitude; W-- west longitude; N-- north latitude; S-- south latitude. In
this example, uses E and N, please according to the actual geographical position choose
corresponding coordinate form to set. In the demonstration, meanings of various parts are as
follows:
16
Eddd.ddddd is longitude information with units of degrees, and the ddd.ddddd expresses
degree (Accuracy for 5 after the decimal point, the following zero cannot bypass)
Ndd.ddddd is latitude information with units of degrees, and the ddd.ddddd expresses degree
(Accuracy for 5 after the decimal point, the following zero cannot bypass)
Rzzz.z is radius for the domain (999.9 - 0.1), unit for KM.
When the tracker receives this instruction, judges to be authorized users and confirms the user
password correctly, it will send the confirmation messages “SET GEO-FENCE OK” to the sender.
Note: 1. Radius of the fence can not exceed the definition of its domain; the value of the
decimal part for zero must input zero fill. For example: R=1, it is important to enter into 1.0.
2. If the calling state is off, it will not call the user telephone number, and only send
messages to the present number.
3. Degree and minute is divided into sexagesimal system converter, that is, 1d = 60m
Format 3 : 005+User Password Rzzz.z
eg: 0050000R0.1
Note : When this unit receive this command and confirm the password is right. And read the
Update gps data whether is available. If ok, take the lat/log to the coordination, and the R for
The Radius, and also pen the Geofence at the same time. If the configuration is ok. The unit
Will send "set geo fence ok " to the sender. If the update GPS Data void, the unit will give
up and then red the next one, if the unit can't receive the data above 50sec, the unit will send
A message to the sender which is "ERROR GPS DATA, TRY AGAIN LATER"
After set ok, the unit will come back the original state.
2) open the electronic fence: 211 + user password
After set successfully, it will send the confirmation messages “GEO-FENCE ON” to the
sender.
3) close the electronic fence: 210 + user password"ERROR GPS DATA, TRY AGAIN LATER"
After set successfully, it will send the confirmation messages “GEO-FENCE OFF” to the sender.
Note: 1. Radius of the fence can not exceed the definition of its domain; the value of the
decimal part for zero must input zero fill. For example: R=1, it is important to enter into 1.0.
2. If the calling state is off, it will not call the user telephone number, and only send
messages to the present number.
3. Degree and minute is divided into sexagesimal system converter, that is, 1d =
17
60m
Attention :
User can choose one of three way to set the Geo- fence . The unit will open
this function after receive the command, the last operation is available
when close this function then open it again.
2 Set up the TCP/IP server and IP’s address and port number
19
Format:#804#user password#fixed IP address # port ##
eg:#804#0000#222.125.12.32#80##
Explanation: When TLT-1B tracker receives the instruction and confirms the user password correctly,
updates the IP address and port number preserved in the module,After the success, it will send the
confirmation messages to the sender. The content is “SET SERVER IP AND PORT OK”
After you complete the three steps, then you can track your car in the platform.
22
Speed: Speed KM/H (Accuracy for 2 after the decimal point)
Direction: Direction (Accuracy for 2 after the decimal point)
Date: Date YYYY-MM-DD
Time: Time HH:MM:SS (GMT)
BS: Base Station information
Fix: Location state (A/V)
ID: IMEI
STATE: Message state
Effective data format:
Lat: +22.50500
Long: +114.01000
Speed: 0.00KM/H
Direction: 315.00
Date: 2008-04-25
Time: 16:39:45
BS: 25ee0dff
Fix: A
ID: 353686009002030
STATE: SMS
Invalid data format:
Lat: +22.50500
Long: +114.01000
Speed: 0.00KM/H
Direction: 315.00
Date: 2008-04-25
Time: 16:39:45
BS: 25ee0dff
Fix: V
ID: 353686009002030
STATE: SMS
BS: 27971054”
23
ID: 353686009002030
STATE: SMS
Note: If in the cold start and GPS no position, it will return to the void of information:
eg: ERROR GPS GPRMC FRAME DATA
24
#25ee0dff$GPRMC,083945.180,A,2233.4249,N,11406.0046,E,0.00,315.00,251207,,,A*6E
#25ee0dff$GPRMC,083950.180,A,2233.4249,N,11406.0046,E,0.00,315.00,251207,,,A*6E
#25ee0dff$GPRMC,083955.180,A,2233.4249,N,11406.0046,E,0.00,315.00,251207,,,A*6E ##
Attention : Immediately upload data format for the state: SMS
26
eg: 003xxxxE11406.0024N2233.4230R1
Explanation: E-- east longitude; W-- west longitude; N-- north latitude; S-- south latitude. In
this example, uses E and N, please according to the actual geographical position choose
corresponding coordinate form to set. In the demonstration, meanings of various parts are as
follows:
Edddmm.mmmm is longitude information with units of degrees and minutes, and the ddd
expresses degree, mm.mmmm expresses minute (Accuracy for 4 after the decimal point, the
following zero cannot bypass)
Ndd.mmmm is latitude information with units of degrees and minutes and the dd expresses
degree, mm.mmmm expresses minute (Accuracy for 4 after the decimal point, the following zero
cannot bypass)
Rzzz.z is radius for the domain (999.9 - 0.1), unit for KM.
When the tracker receives this instruction, judges to be authorized users and confirms the user
password correctly, it will send the confirmation messages “SET GEO-FENCE OK” to the sender.
Format2:004+ user password E/Wddd.dddddN/Sdd.dddddRzzz.z
eg:0040000E114.10004N22.55705R999.9
Explanation: E-- east longitude; W-- west longitude; N-- north latitude; S-- south latitude. In
this example, uses E and N, please according to the actual geographical position choose
corresponding coordinate form to set. In the demonstration, meanings of various parts are as
follows:
Eddd.ddddd is longitude information with units of degrees, and the ddd.ddddd expresses
degree (Accuracy for 5 after the decimal point, the following zero cannot bypass)
Ndd.ddddd is latitude information with units of degrees, and the ddd.ddddd expresses degree
(Accuracy for 5 after the decimal point, the following zero cannot bypass)
Rzzz.z is radius for the domain (999.9 - 0.1), unit for KM.
When the tracker receives this instruction, judges to be authorized users and confirms the user
password correctly, it will send the confirmation messages “SET GEO-FENCE OK” to the sender.
Format 3 : 005+User Password Rzzz.z
eg: 0050000R0.1
Note : When this unit receive this command and confirm the password is right. And read the
Update gps data whether is available. If ok, take the lat/log to the coordination, and the R for
27
The Radius, and also pen the Geofence at the same time. If the configuration is ok. The unit
Will send "set geo fence ok " to the sender. If the update GPS Data void, the unit will give
up and then red the next one, if the unit can't receive the data above 50sec, the unit will send
A message to the sender which is "ERROR GPS DATA, TRY AGAIN LATER"
Note: 1. Radius of the fence can not exceed the definition of its domain; the value of the
decimal part for zero must input zero fill. For example: R=1, it is important to enter into 1.0.
2. If the calling state is off, it will not call the user telephone number, and only send
messages to the present number.
3. Degree and minute is divided into sexagesimal system converter, that is, 1d =
60m
2) open the electronic fence: 211 + user password
After set successfully, it will send the confirmation messages “GEO-FENCE ON” to the
sender.
3) close the electronic fence: 210 + user password
After set successfully, it will send the confirmation messages “GEO-FENCE OFF” to the
sender.
Attention : User can choose one of three way to set the Geo- fence . The unit will open this function
after receive the command, the last operation is available when close this function then open it
again.
Attention :
1, the memory of every data is 100B, the unit can save about 5000PCS Data.
2, when the data is above 5000PCS Data, the new data will recovery the old data automatically.
3. If the Move Sensor is open already, and the car is always stop , the History Record will close
automatically until the unit is wake.
30